The Wire Image of a Network Protocol
draft-iab-wire-image-01

Abstract

This document defines the wire image, an abstraction of the information available to an on-path non-participant in a networking protocol. This abstraction is intended to shed light on the implications on increased encryption has for network functions that use the wire image.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on May 9, 2019.

Copyright Notice

Copyright (c) 2018 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.

1. Introduction

A protocol specification defines a set of behaviors for each participant in the protocol: which lower-layer protocols are used for which services, how messages are formatted and protected, which participant sends which message when, how each participant should respond to each message, and so on.

Implicit in a protocol specification is the information the protocol radiates toward nonparticipant observers of the messages sent among participants, often including participants in lower layer protocols. Any information that has a clear definition in the protocol’s message format(s), or is implied by that definition, and is not cryptographically confidentiality-protected can be unambiguously interpreted by those observers. This information comprises the protocol’s wire image, which we define and discuss in this document.

It is the wire image, not the protocol’s specification, that determines how third parties on the network paths among protocol participants will interact with that protocol.

The increasing deployment of transport-layer security [RFC8226] to protect application-layer headers and payload, as well as the definition and deployment of QUIC [QUIC], a transport protocol which encrypts most of its own control information, bring new relevance to this question. QUIC is, in effect, the first IETF-defined transport protocol to take care of the minimization of its own wire image, to prevent ossification and improve end-to-end privacy by reducing information radiation.

The flipside of this trend is the impact of a less visible wire image on various functions driven by third-party observation of the wire image. In contrast to ongoing discussions about this tussle, this draft treats the wire image as a pure abstraction, with the hope that it can shed some light on these discussions.

2. Definition

The wire image of the set of protocols in use for a given communication is the view of that set of protocols as observed by an entity not participating in the communication. It is the sequence of packets sent by each participant in the communication, including the content of those packets and metadata about the observation itself: the time at which each packet is observed, and the vantage point of the observer.

3. Discussion

This definition illustrates some important properties of the wire image.

Key is that the wire image is not limited to merely “the unencrypted bits in the header”. In particular, the metadata, such as sequences of interpacket timing and packet sizes, can also be used to infer other parameters of the behavior of the protocols in use, or to fingerprint protocols and/or specific implementations of those protocols; see Section 3.2.

An important implication of this property is that a protocol which uses confidentiality protection for the headers it needs to operate can be deliberately designed to have a specified wire image that is separate from that machinery; see Section 4. Note that this is a capability unique to encrypted protocols. Parts of a wire image may also be made visible to devices on path, but immutable through end-to-end integrity protection; see Section 3.3.

Portions of the wire image of a protocol stack that are neither confidentiality-protected nor integrity-protected are writable by devices on the path(s) between the endpoints using the protocols. A protocol with a wire image that is largely writable operating over a path with devices that understand the semantics of the protocol’s wire image can modify it, in order to induce behaviors at the protocol’s participants. TCP is one such protocol in the current Internet.

The term “wire image” can be applied in different scopes: the wire image of a single packet refers to the information derivable from observing that one packet in isolation; the wire image of a single protocol refers to the information derivable from observing only the headers belonging to that protocol on a sequence of packets, in isolation from other protocols in use for a communication. See Section 3.1 for more.

For a given packet observed at a given point in the network, the wire image contains information from the entire stack of protocols in use at that observation point. This implies that the wire image depends on the observer as well: each observer may see a slightly different image of the same communication.

In this document, we assume that only information at the transport layer and above is delivered end-to-end, and focus on the “Internet” wire image: that portion of the wire image at the network layer and above. While confidentiality and integrity protection may be added at multiple layers in the stack, MAC-layer integrity and confidentiality protection do not prevent modification by the devices terminating those security associations, or by devices on different segments of the path.

3.1. The Extent of the Wire Image

While we begin this definition as the properties of a sequence of packets in isolation, this is not how wire images are typically used by passive observers. A passive observer will generally consider the union of all the information in the wire image in all the packets generated by a given conversation.

Similarly, the wire image of a single protocol is rarely seen in isolation. The dynamics of the application and network stacks on each endpoint use multiple protocols for any higher level task. Most protocols involving user content, for example, are often seen on the wire together with DNS traffic; the information from the wire image from each protocol in use for a given communication can be correlated to infer information about the dynamics of the overlying application.

Information from protocol wire images is also not generally used on its own, but is rather additionally correlated with other context information available to the observer: e.g. information about other communications engaged in by each endpoint, information about the implementations of the protocols at each endpoint, information about the network and internetwork topology near those endpoints, and so on. This context can be used together with information from the wire image to reach more detailed inferences about endpoint and end-user behavior.

Note also that the wire image is multidimensional. This implies that the name “image” is not merely metaphorical, and that general image recognition techniques may be applicable to extracting patterns and information from it.

3.2. Obscuring timing and sizing information

Cryptography can protect the confidentiality of a protocol’s headers, to the extent that forwarding devices do not need the confidentiality-protected information for basic forwarding operations. Ciphersuites and other transmission techniques designed to prevent timing analysis can also be applied at the sender to reduce the information content of the metadata portion of the wire image. However, there are limits to these techniques. Packets cannot be made smaller than their information content, sent faster than processing time requirements at the sender allow, or transmitted through the network faster than a factor less than one of the speed of light. Since these techniques operate at the expense of bandwidth efficiency and latency, they are also limited to the application’s tolerance for latency and bandwidth inefficiency.

3.3. Integrity Protection of the Wire Image

Adding end-to-end integrity protection to portions of the wire image makes it impossible for on-path devices to modify them without detection by the endpoints, which can then take action in response to those modifications, making these portions of the wire image effectively immutable. However, they can still be observed by devices on path. This allows the creation of signals intended by the endpoints solely for the consumption of these on-path devices.

Integrity protection can only practically be applied to the sequence of bits in each packet, which implies that a protocol’s visible wire image cannot be made completely immutable in a packet-switched network. Interarrival timings, for instance, cannot be easily protected, as the observable delay sequence is modified as packets move through the network and experience different delays on different links. Message sequences are also not practically protectable, as packets may be dropped or reordered at any point in the network, as a consequence of the network’s operation. Intermediate systems with knowledge of the protocol semantics in the readable portion of the wire image can also purposely delay or drop packets in order to affect the protocol’s operation.

4. Engineering the Wire Image

Understanding the nature of a protocol’s wire image allows it to be engineered. The general principle at work here, observed through experience with deployability and non-deployability of protocols at the network and transport layers in the Internet, is that all observable parts of a protocol’s wire image will eventually be used by devices on path; consequently, changes or future extensions that affect the observable part of the wire image become difficult or impossible to deploy.

A network function which serves a purpose useful to its deployer will use the information it needs from the wire image, and will tend to get that information from the wire image in the simplest way possible.

For example, consider the case of the ubiquitous TCP [RFC0793] transport protocol. As described in [PATH-SIGNALS], several key in-network functions have evolved to take advantage of implicit signals in TCP’s wire image, which, as TCP provides neither integrity or confidentiality protection for its headers, is inseparable from its internal operation. Some of these include:

• Determining return routability and consent: For example, TCP’s wire image contains both an implicit indication that the sender of a packet is at least on the path toward its source address (in the acknowledgement number during the handshake), as well as an implicit indication that a receiving device consents to continue communication. These are used by stateful network firewalls.
• Measuring loss and latency: For example, examining the sequence of TCP’s sequence and acknowledgement numbers, as well as the ECN [RFC3168] control bits allows the inference of congestion, loss and retransmission along the path. The sequence and acknowledgement numbers together with the timestamp option [RFC7323] allow the measurement of application-experienced latency.

During the design of a protocol, the utility of features such as these should be considered. The protocol’s wire image can be designed to explicitly expose information to those network functions deemed important by the designers. The wire image should expose as little other information as possible.

However, even when information is explicitly provided to the network, any information that is exposed by the wire image, even that information not intended to be consumed by an observer, must be designed carefully, as deployed network functions using that information may render it immutable for future versions of the protocol. For example, information needed to support decryption by the receiving endpoint (cryptographic handshakes, sequence numbers, and so on) may be used by devices along the path for their own purposes.

4.1. Declaring Protocol Invariants

One potential approach to reduce the extent of the wire image that will be used by devices on the path is to define a set of invariants for a protocol during its development. Declaring a protocol’s invariants represents a promise made by the protocol’s developers that certain bits in the wire image, and behaviors observable in the wire image, will be preserved through the specification of all future versions of the protocol. QUIC’s invariants [QUIC-INVARIANTS] are an initial attempt to apply this approach to QUIC.

While static aspects of the wire image – bits with simple semantics at fixed positions in protocol headers – can easily be made invariant, different aspects of the wire image may be more or less appropriate to define as invariants. For a protocol with a version and/or extension negotiation mechanism, the bits in the header and behaviors tied to those bits which implement version negotiation should be made invariant. More fluid aspects of the wire image and behaviors which are not necessary for interoperability are not appropriate as invariants.

Parts of a protocol’s wire image not declared invariant but intended to be visible to devices on path should be protected against “accidental invariance”: the deployment of on-path devices over time that make simplifying assumptions about the behavior of those parts of the wire image, making new behaviors not meeting those assumptions difficult to deploy. Integrity protection of the wire image may itself help protect against accidental invariance, because read-only wire images invite less meddling than path-writable wire images. The techniques discussed in [USE-IT] may also be useful in further preventing accidental invariance and ossification.

Likewise, parts of a protocol’s wire image not declared invariant and not intended to be visible to the path should be encrypted to protect their confidentiality. When confidentiality protection is either not possible or not practical, then, as above, the approaches discussed in [USE-IT] may be useful in ossification prevention.

4.2. Trustworthiness of Engineered Signals

Since they are separate from the signals that drive an encrypted protocol’s mechanisms, the accuracy of integrity-protected signals in an engineered wire image intended for consumption by the path may not be verifiable by on-path devices; see [PATH-SIGNALS]. Indeed, any two endpoints with a secret channel between them (in this case, the encrypted protocol itself) may collude to change the semantics and information content of these signals. This is an unavoidable consequence of the separation of the wire image from the protocol’s operation afforded by confidentiality protection of the protocol’s headers.

5. Acknowledgments

Thanks to Martin Thomson, Stephen Farrell, Thomas Fossati, Ted Hardie, Mark Nottingham, Tommy Pauly, and the membership of the IAB Stack Evolution Program, for text, feedback, and discussions that have improved this document.

This work is partially supported by the European Commission under Horizon 2020 grant agreement no. 688421 Measurement and Architecture for a Middleboxed Internet (MAMI), and by the Swiss State Secretariat for Education, Research, and Innovation under contract no. 15.0268. This support does not imply endorsement.

6. Informative References

Authors' Addresses

Table of Contents

• 1. Introduction
• 2. Definition
• 3. Discussion
• 3.1. The Extent of the Wire Image
• 3.2. Obscuring timing and sizing information
• 3.3. Integrity Protection of the Wire Image
• 4. Engineering the Wire Image
• 4.1. Declaring Protocol Invariants
• 4.2. Trustworthiness of Engineered Signals
• 5. Acknowledgments
• 6. Informative References
• Authors' Addresses