| Network Working Group | S. Perreault |
| Internet-Draft | Viagénie |
| Obsoletes: 4008 (if approved) | T. Tsou |
| Intended status: Standards Track | Huawei Technologies (USA) |
| Expires: July 28, 2014 | S. Sivakumar |
| Cisco Systems | |
| January 24, 2014 |
Definitions of Managed Objects for Network Address Translators (NAT)
draft-ietf-behave-nat-mib-11
This memo defines a portion of the Management Information Base (MIB) for devices implementing Network Address Translator (NAT) function. This MIB module may be used for monitoring of a device capable of NAT function.
This document obsoletes RFC 4008.
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."
This Internet-Draft will expire on July 28, 2014.
Copyright (c) 2014 IETF Trust and the persons identified as the document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.
This memo defines a portion of the Management Information Base (MIB) for devices implementing NAT function. This MIB module may be used for monitoring of a device capable of NAT function. Using it for configuration is deprecated. NAT types and their characteristics are defined in [RFC2663]. Traditional NAT function, in particular is defined in [RFC3022]. This MIB does not address the firewall functions and must not be used for configuring or monitoring these. Section 2 provides references to the SNMP management framework, which was used as the basis for the MIB module definition. Section 3 provides an overview of the MIB features. Lastly, Section 4 has the complete NAT MIB definition.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119].
For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580].
All objects defined in [RFC4008] have been marked with "STATUS deprecated" for the following reasons:
New features in this module are as follows:
Current NAT devices commonly allow the internal and external parts of a mapping to come from different realms. The meaning of "realm" is implementation-dependent. On some implementations it can be equivalent to the name of a VPN Routing and Forwarding table (VRF). On others it is simply the numeric index of a virtual routing table. Note that this usage of "realm" is completely different from the one in [RFC4008].
This MIB allows the realm to be indicated where it makes sense. The format is an SnmpAdminString. On platforms that identify realms with integers, the string representation of the integer is used instead. The empty string has special meaning: it refers to the default realm.
Note that many MIBs implicitly support realms in one form or another by using SNMPv3 contexts. See for example the OSPFv2 MIB [RFC4750]. This method cannot be used for the NAT MIB because mapppings can belong to two realms simultaneously: the internal part can be in one realm while the external part is in another. In such cases the NAT function acts like a "wormhole" between two realms. Using contexts would implicitly impose the restriction that all objects would have to belong to the same realm.
This MIB module IMPORTs objects from [RFC2578], [RFC2579], and [RFC4001].
NAT-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Integer32,
Unsigned32,
Gauge32,
Counter64,
TimeTicks,
mib-2,
NOTIFICATION-TYPE
FROM SNMPv2-SMI
TEXTUAL-CONVENTION,
DisplayString,
StorageType,
RowStatus
FROM SNMPv2-TC
MODULE-COMPLIANCE,
NOTIFICATION-GROUP,
OBJECT-GROUP
FROM SNMPv2-CONF
ifIndex,
ifCounterDiscontinuityGroup,
InterfaceIndex
FROM IF-MIB
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
InetAddressType,
InetAddress,
InetAddressPrefixLength,
InetPortNumber
FROM INET-ADDRESS-MIB
VPNIdOrZero
FROM VPN-TC-STD-MIB;
natMIB MODULE-IDENTITY
LAST-UPDATED "201304260000Z"
-- RFC Ed.: set to publication date
ORGANIZATION
"IETF Behavior Engineering for Hindrance Avoidance
(BEHAVE) Working Group"
CONTACT-INFO
"Working Group Email: behave@ietf.org
Simon Perreault
Viagenie
246 Aberdeen
Quebec, QC G1R 2E1
Canada
Phone: +1 418 656 9254
Email: simon.perreault@viagenie.ca
URI: http://viagenie.ca
Tina Tsou
Huawei Technologies (USA)
2330 Central Expressway
Santa Clara, CA 95050
USA
Phone: +1 408 330 4424
Email: tina.tsou.zouting@huawei.com
Senthil Sivakumar
Cisco Systems
7100-8 Kit Creek Road
Research Triangle Park, North Carolina 27709
USA
Phone: +1 919 392 5158
Email: ssenthil@cisco.com"
DESCRIPTION
"This MIB module defines the generic managed objects
for NAT.
Copyright (C) The Internet Society (2013). This
version of this MIB module is part of RFC yyyy; see
the RFC itself for full legal notices."
-- RFC Ed.: replace yyyy with actual RFC number & remove this note"
REVISION "201304260000Z"
-- RFC Ed.: set to publication date
DESCRIPTION
"Complete rewrite, published as RFC yyyy."
-- RFC Ed.: replace yyyy with actual RFC number & set date"
REVISION "200503210000Z" -- 21th March 2005
DESCRIPTION
"Initial version, published as RFC 4008."
::= { mib-2 123 }
natMIBObjects OBJECT IDENTIFIER ::= { natMIB 1 }
NatProtocolType ::= TEXTUAL-CONVENTION
STATUS deprecated
DESCRIPTION
"A list of protocols that support the network
address translation. Inclusion of the values is
not intended to imply that those protocols
need to be supported. Any change in this
TEXTUAL-CONVENTION should also be reflected in
the definition of NatProtocolMap, which is a
BITS representation of this."
SYNTAX INTEGER {
none (1), -- not specified
other (2), -- none of the following
icmp (3),
udp (4),
tcp (5)
}
NatProtocolMap ::= TEXTUAL-CONVENTION
STATUS deprecated
DESCRIPTION
"A bitmap of protocol identifiers that support
the network address translation. Any change
in this TEXTUAL-CONVENTION should also be
reflected in the definition of NatProtocolType."
SYNTAX BITS {
other (0),
icmp (1),
udp (2),
tcp (3)
}
NatAddrMapId ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS deprecated
DESCRIPTION
"A unique id that is assigned to each address map
by a NAT enabled device."
SYNTAX Unsigned32 (1..4294967295)
NatBindIdOrZero ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS deprecated
DESCRIPTION
"A unique id that is assigned to each bind by
a NAT enabled device. The bind id will be zero
in the case of a Symmetric NAT."
SYNTAX Unsigned32 (0..4294967295)
NatBindId ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS deprecated
DESCRIPTION
"A unique id that is assigned to each bind by
a NAT enabled device."
SYNTAX Unsigned32 (1..4294967295)
NatSessionId ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS deprecated
DESCRIPTION
"A unique id that is assigned to each session by
a NAT enabled device."
SYNTAX Unsigned32 (1..4294967295)
NatBindMode ::= TEXTUAL-CONVENTION
STATUS deprecated
DESCRIPTION
"An indication of whether the bind is
an address bind or an address port bind."
SYNTAX INTEGER {
addressBind (1),
addressPortBind (2)
}
NatAssociationType ::= TEXTUAL-CONVENTION
STATUS deprecated
DESCRIPTION
"An indication of whether the association is
static or dynamic."
SYNTAX INTEGER {
static (1),
dynamic (2)
}
NatTranslationEntity ::= TEXTUAL-CONVENTION
STATUS deprecated
DESCRIPTION
"An indication of a) the direction of a session for
which an address map entry, address bind or port
bind is applicable, and b) the entity (source or
destination) within the session that is subject to
translation."
SYNTAX BITS {
inboundSrcEndPoint (0),
outboundDstEndPoint(1),
inboundDstEndPoint (2),
outboundSrcEndPoint(3)
}
--
-- Default Values for the Bind and NAT Protocol Timers
--
natDefTimeouts OBJECT IDENTIFIER ::= { natMIBObjects 1 }
natNotifCtrl OBJECT IDENTIFIER ::= { natMIBObjects 2 }
--
-- Address Bind and Port Bind related NAT configuration
--
natBindDefIdleTimeout OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
UNITS "seconds"
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"The default Bind (Address Bind or Port Bind) idle
timeout parameter.
If the agent is capable of storing non-volatile
configuration, then the value of this object must be
restored after a re-initialization of the management
system."
DEFVAL { 0 }
::= { natDefTimeouts 1 }
--
-- UDP related NAT configuration
--
natUdpDefIdleTimeout OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
UNITS "seconds"
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"The default UDP idle timeout parameter.
If the agent is capable of storing non-volatile
configuration, then the value of this object must be
restored after a re-initialization of the management
system."
DEFVAL { 300 }
::= { natDefTimeouts 2 }
--
-- ICMP related NAT configuration
--
natIcmpDefIdleTimeout OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
UNITS "seconds"
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"The default ICMP idle timeout parameter.
If the agent is capable of storing non-volatile
configuration, then the value of this object must be
restored after a re-initialization of the management
system."
DEFVAL { 300 }
::= { natDefTimeouts 3 }
--
-- Other protocol parameters
--
natOtherDefIdleTimeout OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
UNITS "seconds"
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"The default idle timeout parameter for protocols
represented by the value other (2) in
NatProtocolType.
If the agent is capable of storing non-volatile
configuration, then the value of this object must be
restored after a re-initialization of the management
system."
DEFVAL { 60 }
::= { natDefTimeouts 4 }
--
-- TCP related NAT Timers
--
natTcpDefIdleTimeout OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
UNITS "seconds"
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"The default time interval that a NAT session for an
established TCP connection is allowed to remain
valid without any activity on the TCP connection.
If the agent is capable of storing non-volatile
configuration, then the value of this object must be
restored after a re-initialization of the management
system."
DEFVAL { 86400 }
::= { natDefTimeouts 5 }
natTcpDefNegTimeout OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
UNITS "seconds"
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"The default time interval that a NAT session for a TCP
connection that is not in the established state
is allowed to remain valid without any activity on
the TCP connection.
If the agent is capable of storing non-volatile
configuration, then the value of this object must be
restored after a re-initialization of the management
system."
DEFVAL { 60 }
::= { natDefTimeouts 6 }
natNotifThrottlingInterval OBJECT-TYPE
SYNTAX Integer32 (0 | 5..3600)
UNITS "seconds"
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"This object controls the generation of the
natPacketDiscard notification.
If this object has a value of zero, then no
natPacketDiscard notifications will be transmitted by
the agent.
If this object has a non-zero value, then the agent must
not generate more than one natPacketDiscard
'notification-event' in the indicated period, where a
'notification-event' is the generation of a single
notification PDU type to a list of notification
destinations. If additional NAT packets are discarded
within the throttling period, then notification-events
for these changes must be suppressed by the agent until
the current throttling period expires.
If natNotifThrottlingInterval notification generation
is enabled, the suggested default throttling period is
60 seconds, but generation of the natPacketDiscard
notification should be disabled by default.
If the agent is capable of storing non-volatile
configuration, then the value of this object must be
restored after a re-initialization of the management
system.
The actual transmission of notifications is controlled
via the MIB modules in RFC 3413."
DEFVAL { 0 }
::= { natNotifCtrl 1 }
--
-- The NAT Interface Table
--
natInterfaceTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatInterfaceEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This table specifies the attributes for interfaces on a
device supporting NAT function."
::= { natMIBObjects 3 }
natInterfaceEntry OBJECT-TYPE
SYNTAX NatInterfaceEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"Each entry in the natInterfaceTable holds a set of
parameters for an interface, instantiated by
ifIndex. Therefore, the interface index must have been
assigned, according to the applicable procedures,
before it can be meaningfully used.
Generally, this means that the interface must exist.
When natStorageType is of type nonVolatile, however,
this may reflect the configuration for an interface
whose ifIndex has been assigned but for which the
supporting implementation is not currently present."
INDEX { ifIndex }
::= { natInterfaceTable 1 }
NatInterfaceEntry ::= SEQUENCE {
natInterfaceRealm INTEGER,
natInterfaceServiceType BITS,
natInterfaceInTranslates Counter64,
natInterfaceOutTranslates Counter64,
natInterfaceDiscards Counter64,
natInterfaceStorageType StorageType,
natInterfaceRowStatus RowStatus
}
natInterfaceRealm OBJECT-TYPE
SYNTAX INTEGER {
private (1),
public (2)
}
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object identifies whether this interface is
connected to the private or the public realm."
DEFVAL { public }
::= { natInterfaceEntry 1 }
natInterfaceServiceType OBJECT-TYPE
SYNTAX BITS {
basicNat (0),
napt (1),
bidirectionalNat (2),
twiceNat (3)
}
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"An indication of the direction in which new sessions
are permitted and the extent of translation done within
the IP and transport headers."
::= { natInterfaceEntry 2 }
natInterfaceInTranslates OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Number of packets received on this interface that
were translated.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natInterfaceEntry 3 }
natInterfaceOutTranslates OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Number of translated packets that were sent out this
interface.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natInterfaceEntry 4 }
natInterfaceDiscards OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Number of packets that had to be rejected/dropped due to
a lack of resources for this interface.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natInterfaceEntry 5 }
natInterfaceStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The storage type for this conceptual row.
Conceptual rows having the value 'permanent'
need not allow write-access to any columnar objects
in the row."
REFERENCE
"Textual Conventions for SMIv2, Section 2."
DEFVAL { nonVolatile }
::= { natInterfaceEntry 6 }
natInterfaceRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The status of this conceptual row.
Until instances of all corresponding columns are
appropriately configured, the value of the
corresponding instance of the natInterfaceRowStatus
column is 'notReady'.
In particular, a newly created row cannot be made
active until the corresponding instance of
natInterfaceServiceType has been set.
None of the objects in this row may be modified
while the value of this object is active(1)."
REFERENCE
"Textual Conventions for SMIv2, Section 2."
::= { natInterfaceEntry 7 }
--
-- The Address Map Table
--
natAddrMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatAddrMapEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This table lists address map parameters for NAT."
::= { natMIBObjects 4 }
natAddrMapEntry OBJECT-TYPE
SYNTAX NatAddrMapEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This entry represents an address map to be used for
NAT and contributes to the dynamic and/or static
address mapping tables of the NAT device."
INDEX { ifIndex, natAddrMapIndex }
::= { natAddrMapTable 1 }
NatAddrMapEntry ::= SEQUENCE {
natAddrMapIndex NatAddrMapId,
natAddrMapName SnmpAdminString,
natAddrMapEntryType NatAssociationType,
natAddrMapTranslationEntity NatTranslationEntity,
natAddrMapLocalAddrType InetAddressType,
natAddrMapLocalAddrFrom InetAddress,
natAddrMapLocalAddrTo InetAddress,
natAddrMapLocalPortFrom InetPortNumber,
natAddrMapLocalPortTo InetPortNumber,
natAddrMapGlobalAddrType InetAddressType,
natAddrMapGlobalAddrFrom InetAddress,
natAddrMapGlobalAddrTo InetAddress,
natAddrMapGlobalPortFrom InetPortNumber,
natAddrMapGlobalPortTo InetPortNumber,
natAddrMapProtocol NatProtocolMap,
natAddrMapInTranslates Counter64,
natAddrMapOutTranslates Counter64,
natAddrMapDiscards Counter64,
natAddrMapAddrUsed Gauge32,
natAddrMapStorageType StorageType,
natAddrMapRowStatus RowStatus
}
natAddrMapIndex OBJECT-TYPE
SYNTAX NatAddrMapId
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"Along with ifIndex, this object uniquely
identifies an entry in the natAddrMapTable.
Address map entries are applied in the order
specified by natAddrMapIndex."
::= { natAddrMapEntry 1 }
natAddrMapName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"Name identifying all map entries in the table associated
with the same interface. All map entries with the same
ifIndex MUST have the same map name."
::= { natAddrMapEntry 2 }
natAddrMapEntryType OBJECT-TYPE
SYNTAX NatAssociationType
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This parameter can be used to set up static
or dynamic address maps."
::= { natAddrMapEntry 3 }
natAddrMapTranslationEntity OBJECT-TYPE
SYNTAX NatTranslationEntity
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The end-point entity (source or destination) in
inbound or outbound sessions (i.e., first packets) that
may be translated by an address map entry.
Session direction (inbound or outbound) is
derived from the direction of the first packet
of a session traversing a NAT interface.
NAT address (and Transport-ID) maps may be defined
to effect inbound or outbound sessions.
Traditionally, address maps for Basic NAT and NAPT are
configured on a public interface for outbound sessions,
effecting translation of source end-point. The value of
this object must be set to outboundSrcEndPoint for
those interfaces.
Alternately, if address maps for Basic NAT and NAPT were
to be configured on a private interface, the desired
value for this object for the map entries
would be inboundSrcEndPoint (i.e., effecting translation
of source end-point for inbound sessions).
If TwiceNAT were to be configured on a private
interface, the desired value for this object for the map
entries would be a bitmask of inboundSrcEndPoint and
inboundDstEndPoint."
::= { natAddrMapEntry 4 }
natAddrMapLocalAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object specifies the address type used for
natAddrMapLocalAddrFrom and natAddrMapLocalAddrTo."
::= { natAddrMapEntry 5 }
natAddrMapLocalAddrFrom OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object specifies the first IP address of the range
of IP addresses mapped by this translation entry. The
value of this object must be less than or equal to the
value of the natAddrMapLocalAddrTo object.
The type of this address is determined by the value of
the natAddrMapLocalAddrType object."
::= { natAddrMapEntry 6 }
natAddrMapLocalAddrTo OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object specifies the last IP address of the range
of IP addresses mapped by this translation entry. If
only a single address is being mapped, the value of this
object is equal to the value of natAddrMapLocalAddrFrom.
For a static NAT, the number of addresses in the range
defined by natAddrMapLocalAddrFrom and
natAddrMapLocalAddrTo must be equal to the number of
addresses in the range defined by
natAddrMapGlobalAddrFrom and natAddrMapGlobalAddrTo.
The value of this object must be greater than or equal
to the value of the natAddrMapLocalAddrFrom object.
The type of this address is determined by the value of
the natAddrMapLocalAddrType object."
::= { natAddrMapEntry 7 }
natAddrMapLocalPortFrom OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"If this conceptual row describes a Basic NAT address
mapping, then the value of this object must be zero. If
this conceptual row describes NAPT, then the value of
this object specifies the first port number in the range
of ports being mapped.
The value of this object must be less than or equal to
the value of the natAddrMapLocalPortTo object. If the
translation specifies a single port, then the value of
this object is equal to the value of
natAddrMapLocalPortTo."
DEFVAL { 0 }
::= { natAddrMapEntry 8 }
natAddrMapLocalPortTo OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"If this conceptual row describes a Basic NAT address
mapping, then the value of this object must be zero. If
this conceptual row describes NAPT, then the value of
this object specifies the last port number in the range
of ports being mapped.
The value of this object must be greater than or equal
to the value of the natAddrMapLocalPortFrom object. If
the translation specifies a single port, then the value
of this object is equal to the value of
natAddrMapLocalPortFrom."
DEFVAL { 0 }
::= { natAddrMapEntry 9 }
natAddrMapGlobalAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object specifies the address type used for
natAddrMapGlobalAddrFrom and natAddrMapGlobalAddrTo."
::= { natAddrMapEntry 10 }
natAddrMapGlobalAddrFrom OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object specifies the first IP address of the range
of IP addresses being mapped to. The value of this
object must be less than or equal to the value of the
natAddrMapGlobalAddrTo object.
The type of this address is determined by the value of
the natAddrMapGlobalAddrType object."
::= { natAddrMapEntry 11 }
natAddrMapGlobalAddrTo OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object specifies the last IP address of the range
of IP addresses being mapped to. If only a single
address is being mapped to, the value of this object is
equal to the value of natAddrMapGlobalAddrFrom. For a
static NAT, the number of addresses in the range defined
by natAddrMapGlobalAddrFrom and natAddrMapGlobalAddrTo
must be equal to the number of addresses in the range
defined by natAddrMapLocalAddrFrom and
natAddrMapLocalAddrTo. The value of this object must be
greater than or equal to the value of the
natAddrMapGlobalAddrFrom object.
The type of this address is determined by the value of
the natAddrMapGlobalAddrType object."
::= { natAddrMapEntry 12 }
natAddrMapGlobalPortFrom OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"If this conceptual row describes a Basic NAT address
mapping, then the value of this object must be zero. If
this conceptual row describes NAPT, then the value of
this object specifies the first port number in the range
of ports being mapped to.
The value of this object must be less than or equal to
the value of the natAddrMapGlobalPortTo object. If the
translation specifies a single port, then the value of
this object is equal to the value
natAddrMapGlobalPortTo."
DEFVAL { 0 }
::= { natAddrMapEntry 13 }
natAddrMapGlobalPortTo OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"If this conceptual row describes a Basic NAT address
mapping, then the value of this object must be zero. If
this conceptual row describes NAPT, then the value of
this object specifies the last port number in the range
of ports being mapped to.
The value of this object must be greater than or equal
to the value of the natAddrMapGlobalPortFrom object. If
the translation specifies a single port, then the value
of this object is equal to the value of
natAddrMapGlobalPortFrom."
DEFVAL { 0 }
::= { natAddrMapEntry 14 }
natAddrMapProtocol OBJECT-TYPE
SYNTAX NatProtocolMap
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object specifies a bitmap of protocol identifiers."
::= { natAddrMapEntry 15 }
natAddrMapInTranslates OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of inbound packets pertaining to this address
map entry that were translated.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times, as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natAddrMapEntry 16 }
natAddrMapOutTranslates OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of outbound packets pertaining to this
address map entry that were translated.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times, as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natAddrMapEntry 17 }
natAddrMapDiscards OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of packets pertaining to this address map
entry that were dropped due to lack of addresses in the
address pool identified by this address map. The value
of this object must always be zero in case of static
address map.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times, as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natAddrMapEntry 18 }
natAddrMapAddrUsed OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of addresses pertaining to this address map
that are currently being used from the NAT pool.
The value of this object must always be zero in the case
of a static address map."
::= { natAddrMapEntry 19 }
natAddrMapStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The storage type for this conceptual row.
Conceptual rows having the value 'permanent'
need not allow write-access to any columnar objects
in the row."
REFERENCE
"Textual Conventions for SMIv2, Section 2."
DEFVAL { nonVolatile }
::= { natAddrMapEntry 20 }
natAddrMapRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The status of this conceptual row.
Until instances of all corresponding columns are
appropriately configured, the value of the
corresponding instance of the natAddrMapRowStatus
column is 'notReady'.
None of the objects in this row may be modified
while the value of this object is active(1)."
REFERENCE
"Textual Conventions for SMIv2, Section 2."
::= { natAddrMapEntry 21 }
--
-- Address Bind section
--
natAddrBindNumberOfEntries OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object maintains a count of the number of entries
that currently exist in the natAddrBindTable."
::= { natMIBObjects 5 }
--
-- The NAT Address BIND Table
--
natAddrBindTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatAddrBindEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This table holds information about the currently
active NAT BINDs."
::= { natMIBObjects 6 }
natAddrBindEntry OBJECT-TYPE
SYNTAX NatAddrBindEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"Each entry in this table holds information about
an active address BIND. These entries are lost
upon agent restart.
This row has indexing which may create variables with
more than 128 subidentifiers. Implementers of this
table must be careful not to create entries that would
result in OIDs which exceed the 128 subidentifier limit.
Otherwise, the information cannot be accessed using
SNMPv1, SNMPv2c or SNMPv3."
INDEX { ifIndex,
natAddrBindLocalAddrType,
natAddrBindLocalAddr }
::= { natAddrBindTable 1 }
NatAddrBindEntry ::= SEQUENCE {
natAddrBindLocalAddrType InetAddressType,
natAddrBindLocalAddr InetAddress,
natAddrBindGlobalAddrType InetAddressType,
natAddrBindGlobalAddr InetAddress,
natAddrBindId NatBindId,
natAddrBindTranslationEntity NatTranslationEntity,
natAddrBindType NatAssociationType,
natAddrBindMapIndex NatAddrMapId,
natAddrBindSessions Gauge32,
natAddrBindMaxIdleTime TimeTicks,
natAddrBindCurrentIdleTime TimeTicks,
natAddrBindInTranslates Counter64,
natAddrBindOutTranslates Counter64
}
natAddrBindLocalAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This object specifies the address type used for
natAddrBindLocalAddr."
::= { natAddrBindEntry 1 }
natAddrBindLocalAddr OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|16))
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This object represents the private-realm specific
network layer address, which maps to the public-realm
address represented by natAddrBindGlobalAddr.
The type of this address is determined by the value of
the natAddrBindLocalAddrType object."
::= { natAddrBindEntry 2 }
natAddrBindGlobalAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object specifies the address type used for
natAddrBindGlobalAddr."
::= { natAddrBindEntry 3 }
natAddrBindGlobalAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object represents the public-realm network layer
address that maps to the private-realm network layer
address represented by natAddrBindLocalAddr.
The type of this address is determined by the value of
the natAddrBindGlobalAddrType object."
::= { natAddrBindEntry 4 }
natAddrBindId OBJECT-TYPE
SYNTAX NatBindId
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object represents a bind id that is dynamically
assigned to each bind by a NAT enabled device. Each
bind is represented by a bind id that is
unique across both, the natAddrBindTable and the
natAddrPortBindTable."
::= { natAddrBindEntry 5 }
natAddrBindTranslationEntity OBJECT-TYPE
SYNTAX NatTranslationEntity
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object represents the direction of sessions
for which this bind is applicable and the endpoint
entity (source or destination) within the sessions that
is subject to translation using the BIND.
Orientation of the bind can be a superset of
translationEntity of the address map entry which
forms the basis for this bind.
For example, if the translationEntity of an
address map entry is outboundSrcEndPoint, the
translationEntity of a bind derived from this
map entry may either be outboundSrcEndPoint or
it may be bidirectional (a bitmask of
outboundSrcEndPoint and inboundDstEndPoint)."
::= { natAddrBindEntry 6 }
natAddrBindType OBJECT-TYPE
SYNTAX NatAssociationType
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object indicates whether the bind is static or
dynamic."
::= { natAddrBindEntry 7 }
natAddrBindMapIndex OBJECT-TYPE
SYNTAX NatAddrMapId
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object is a pointer to the natAddrMapTable entry
(and the parameters of that entry) which was used in
creating this BIND. This object, in conjunction with
the ifIndex (which identifies a unique addrMapName)
points to a unique entry in the natAddrMapTable."
::= { natAddrBindEntry 8 }
natAddrBindSessions OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Number of sessions currently using this BIND."
::= { natAddrBindEntry 9 }
natAddrBindMaxIdleTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object indicates the maximum time for
which this bind can be idle with no sessions
attached to it.
The value of this object is of relevance only for
dynamic NAT."
::= { natAddrBindEntry 10 }
natAddrBindCurrentIdleTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"At any given instance, this object indicates the
time that this bind has been idle without any sessions
attached to it.
The value of this object is of relevance only for
dynamic NAT."
::= { natAddrBindEntry 11 }
natAddrBindInTranslates OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of inbound packets that were successfully
translated by using this bind entry.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times, as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natAddrBindEntry 12 }
natAddrBindOutTranslates OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of outbound packets that were successfully
translated using this bind entry.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natAddrBindEntry 13 }
--
-- Address Port Bind section
--
natAddrPortBindNumberOfEntries OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object maintains a count of the number of entries
that currently exist in the natAddrPortBindTable."
::= { natMIBObjects 7 }
--
-- The NAT Address Port Bind Table
--
natAddrPortBindTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatAddrPortBindEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This table holds information about the currently
active NAPT BINDs."
::= { natMIBObjects 8 }
natAddrPortBindEntry OBJECT-TYPE
SYNTAX NatAddrPortBindEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"Each entry in the this table holds information
about a NAPT bind that is currently active.
These entries are lost upon agent restart.
This row has indexing which may create variables with
more than 128 subidentifiers. Implementers of this
table must be careful not to create entries which would
result in OIDs that exceed the 128 subidentifier limit.
Otherwise, the information cannot be accessed using
SNMPv1, SNMPv2c or SNMPv3."
INDEX { ifIndex, natAddrPortBindLocalAddrType,
natAddrPortBindLocalAddr, natAddrPortBindLocalPort,
natAddrPortBindProtocol }
::= { natAddrPortBindTable 1 }
NatAddrPortBindEntry ::= SEQUENCE {
natAddrPortBindLocalAddrType InetAddressType,
natAddrPortBindLocalAddr InetAddress,
natAddrPortBindLocalPort InetPortNumber,
natAddrPortBindProtocol NatProtocolType,
natAddrPortBindGlobalAddrType InetAddressType,
natAddrPortBindGlobalAddr InetAddress,
natAddrPortBindGlobalPort InetPortNumber,
natAddrPortBindId NatBindId,
natAddrPortBindTranslationEntity NatTranslationEntity,
natAddrPortBindType NatAssociationType,
natAddrPortBindMapIndex NatAddrMapId,
natAddrPortBindSessions Gauge32,
natAddrPortBindMaxIdleTime TimeTicks,
natAddrPortBindCurrentIdleTime TimeTicks,
natAddrPortBindInTranslates Counter64,
natAddrPortBindOutTranslates Counter64
}
natAddrPortBindLocalAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This object specifies the address type used for
natAddrPortBindLocalAddr."
::= { natAddrPortBindEntry 1 }
natAddrPortBindLocalAddr OBJECT-TYPE
SYNTAX InetAddress (SIZE(4|16))
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This object represents the private-realm specific
network layer address which, in conjunction with
natAddrPortBindLocalPort, maps to the public-realm
network layer address and transport id represented by
natAddrPortBindGlobalAddr and natAddrPortBindGlobalPort
respectively.
The type of this address is determined by the value of
the natAddrPortBindLocalAddrType object."
::= { natAddrPortBindEntry 2 }
natAddrPortBindLocalPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"For a protocol value TCP or UDP, this object represents
the private-realm specific port number. On the other
hand, for ICMP a bind is created only for query/response
type ICMP messages such as ICMP echo, Timestamp, and
Information request messages, and this object represents
the private-realm specific identifier in the ICMP
message, as defined in RFC 792 for ICMPv4 and in RFC
2463 for ICMPv6.
This object, together with natAddrPortBindProtocol,
natAddrPortBindLocalAddrType, and
natAddrPortBindLocalAddr, constitutes a session endpoint
in the private realm. A bind entry binds a private
realm specific endpoint to a public realm specific
endpoint, as represented by the tuple of
(natAddrPortBindGlobalPort, natAddrPortBindProtocol,
natAddrPortBindGlobalAddrType, and
natAddrPortBindGlobalAddr)."
::= { natAddrPortBindEntry 3 }
natAddrPortBindProtocol OBJECT-TYPE
SYNTAX NatProtocolType
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This object specifies a protocol identifier. If the
value of this object is none(1), then this bind entry
applies to all IP traffic. Any other value of this
object specifies the class of IP traffic to which this
BIND applies."
::= { natAddrPortBindEntry 4 }
natAddrPortBindGlobalAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object specifies the address type used for
natAddrPortBindGlobalAddr."
::= { natAddrPortBindEntry 5 }
natAddrPortBindGlobalAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object represents the public-realm specific network
layer address that, in conjunction with
natAddrPortBindGlobalPort, maps to the private-realm
network layer address and transport id represented by
natAddrPortBindLocalAddr and natAddrPortBindLocalPort,
respectively.
The type of this address is determined by the value of
the natAddrPortBindGlobalAddrType object."
::= { natAddrPortBindEntry 6 }
natAddrPortBindGlobalPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"For a protocol value TCP or UDP, this object represents
the public-realm specific port number. On the other
hand, for ICMP a bind is created only for query/response
type ICMP messages such as ICMP echo, Timestamp, and
Information request messages, and this object represents
the public-realm specific identifier in the ICMP
message, as defined in RFC 792 for ICMPv4 and in RFC
2463 for ICMPv6.
This object, together with natAddrPortBindProtocol,
natAddrPortBindGlobalAddrType, and
natAddrPortBindGlobalAddr, constitutes a session
endpoint in the public realm. A bind entry binds a
public realm specific endpoint to a private realm
specific endpoint, as represented by the tuple of
(natAddrPortBindLocalPort, natAddrPortBindProtocol,
natAddrPortBindLocalAddrType, and
natAddrPortBindLocalAddr)."
::= { natAddrPortBindEntry 7 }
natAddrPortBindId OBJECT-TYPE
SYNTAX NatBindId
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object represents a bind id that is dynamically
assigned to each bind by a NAT enabled device. Each
bind is represented by a unique bind id across both
the natAddrBindTable and the natAddrPortBindTable."
::= { natAddrPortBindEntry 8 }
natAddrPortBindTranslationEntity OBJECT-TYPE
SYNTAX NatTranslationEntity
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object represents the direction of sessions
for which this bind is applicable and the entity
(source or destination) within the sessions that is
subject to translation with the BIND.
Orientation of the bind can be a superset of the
translationEntity of the address map entry that
forms the basis for this bind.
For example, if the translationEntity of an
address map entry is outboundSrcEndPoint, the
translationEntity of a bind derived from this
map entry may either be outboundSrcEndPoint or
may be bidirectional (a bitmask of
outboundSrcEndPoint and inboundDstEndPoint)."
::= { natAddrPortBindEntry 9 }
natAddrPortBindType OBJECT-TYPE
SYNTAX NatAssociationType
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object indicates whether the bind is static or
dynamic."
::= { natAddrPortBindEntry 10 }
natAddrPortBindMapIndex OBJECT-TYPE
SYNTAX NatAddrMapId
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object is a pointer to the natAddrMapTable entry
(and the parameters of that entry) used in
creating this BIND. This object, in conjunction with
the ifIndex (which identifies a unique addrMapName),
points to a unique entry in the natAddrMapTable."
::= { natAddrPortBindEntry 11 }
natAddrPortBindSessions OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Number of sessions currently using this BIND."
::= { natAddrPortBindEntry 12 }
natAddrPortBindMaxIdleTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object indicates the maximum time for
which this bind can be idle without any sessions
attached to it.
The value of this object is of relevance
only for dynamic NAT."
::= { natAddrPortBindEntry 13 }
natAddrPortBindCurrentIdleTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"At any given instance, this object indicates the
time that this bind has been idle without any sessions
attached to it.
The value of this object is of relevance
only for dynamic NAT."
::= { natAddrPortBindEntry 14 }
natAddrPortBindInTranslates OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of inbound packets that were translated as
per this bind entry.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times, as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natAddrPortBindEntry 15 }
natAddrPortBindOutTranslates OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of outbound packets that were translated as
per this bind entry.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times, as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natAddrPortBindEntry 16 }
--
-- The Session Table
--
natSessionTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatSessionEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The (conceptual) table containing one entry for each
NAT session currently active on this NAT device."
::= { natMIBObjects 9 }
natSessionEntry OBJECT-TYPE
SYNTAX NatSessionEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"An entry (conceptual row) containing information
about an active NAT session on this NAT device.
These entries are lost upon agent restart."
INDEX { ifIndex, natSessionIndex }
::= { natSessionTable 1 }
NatSessionEntry ::= SEQUENCE {
natSessionIndex NatSessionId,
natSessionPrivateSrcEPBindId NatBindIdOrZero,
natSessionPrivateSrcEPBindMode NatBindMode,
natSessionPrivateDstEPBindId NatBindIdOrZero,
natSessionPrivateDstEPBindMode NatBindMode,
natSessionDirection INTEGER,
natSessionUpTime TimeTicks,
natSessionAddrMapIndex NatAddrMapId,
natSessionProtocolType NatProtocolType,
natSessionPrivateAddrType InetAddressType,
natSessionPrivateSrcAddr InetAddress,
natSessionPrivateSrcPort InetPortNumber,
natSessionPrivateDstAddr InetAddress,
natSessionPrivateDstPort InetPortNumber,
natSessionPublicAddrType InetAddressType,
natSessionPublicSrcAddr InetAddress,
natSessionPublicSrcPort InetPortNumber,
natSessionPublicDstAddr InetAddress,
natSessionPublicDstPort InetPortNumber,
natSessionMaxIdleTime TimeTicks,
natSessionCurrentIdleTime TimeTicks,
natSessionInTranslates Counter64,
natSessionOutTranslates Counter64
}
natSessionIndex OBJECT-TYPE
SYNTAX NatSessionId
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The session ID for this NAT session."
::= { natSessionEntry 1 }
natSessionPrivateSrcEPBindId OBJECT-TYPE
SYNTAX NatBindIdOrZero
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The bind id associated between private and public
source end points. In the case of Symmetric-NAT,
this should be set to zero."
::= { natSessionEntry 2 }
natSessionPrivateSrcEPBindMode OBJECT-TYPE
SYNTAX NatBindMode
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object indicates whether the bind indicated
by the object natSessionPrivateSrcEPBindId
is an address bind or an address port bind."
::= { natSessionEntry 3 }
natSessionPrivateDstEPBindId OBJECT-TYPE
SYNTAX NatBindIdOrZero
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The bind id associated between private and public
destination end points."
::= { natSessionEntry 4 }
natSessionPrivateDstEPBindMode OBJECT-TYPE
SYNTAX NatBindMode
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object indicates whether the bind indicated
by the object natSessionPrivateDstEPBindId
is an address bind or an address port bind."
::= { natSessionEntry 5 }
natSessionDirection OBJECT-TYPE
SYNTAX INTEGER {
inbound (1),
outbound (2)
}
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The direction of this session with respect to the
local network. 'inbound' indicates that this session
was initiated from the public network into the private
network. 'outbound' indicates that this session was
initiated from the private network into the public
network."
::= { natSessionEntry 6 }
natSessionUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The up time of this session in one-hundredths of a
second."
::= { natSessionEntry 7 }
natSessionAddrMapIndex OBJECT-TYPE
SYNTAX NatAddrMapId
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object is a pointer to the natAddrMapTable entry
(and the parameters of that entry) used in
creating this session. This object, in conjunction with
the ifIndex (which identifies a unique addrMapName),
points to a unique entry in the natAddrMapTable."
::= { natSessionEntry 8 }
natSessionProtocolType OBJECT-TYPE
SYNTAX NatProtocolType
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The protocol type of this session."
::= { natSessionEntry 9 }
natSessionPrivateAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object specifies the address type used for
natSessionPrivateSrcAddr and natSessionPrivateDstAddr."
::= { natSessionEntry 10 }
natSessionPrivateSrcAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The source IP address of the session endpoint that
lies in the private network.
The value of this object must be zero only when the
natSessionPrivateSrcEPBindId object has a zero value.
When the value of this object is zero, the NAT session
lookup will match any IP address to this field.
The type of this address is determined by the value of
the natSessionPrivateAddrType object."
::= { natSessionEntry 11 }
natSessionPrivateSrcPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"When the value of protocol is TCP or UDP, this object
represents the source port in the first packet of
session while in private-realm. On the other hand, when
the protocol is ICMP, a NAT session is created only for
query/response type ICMP messages such as ICMP echo,
Timestamp, and Information request messages, and this
object represents the private-realm specific identifier
in the ICMP message, as defined in RFC 792 for ICMPv4
and in RFC 2463 for ICMPv6.
The value of this object must be zero when the
natSessionPrivateSrcEPBindId object has zero value
and value of natSessionPrivateSrcEPBindMode is
addressPortBind(2). In such a case, the NAT session
lookup will match any port number to this field.
The value of this object must be zero when the object
is not a representative field (SrcPort, DstPort, or
ICMP identifier) of the session tuple in either the
public realm or the private realm."
::= { natSessionEntry 12 }
natSessionPrivateDstAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The destination IP address of the session endpoint that
lies in the private network.
The value of this object must be zero when the
natSessionPrivateDstEPBindId object has a zero value.
In such a scenario, the NAT session lookup will match
any IP address to this field.
The type of this address is determined by the value of
the natSessionPrivateAddrType object."
::= { natSessionEntry 13 }
natSessionPrivateDstPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"When the value of protocol is TCP or UDP, this object
represents the destination port in the first packet
of session while in private-realm. On the other hand,
when the protocol is ICMP, this object is not relevant
and should be set to zero.
The value of this object must be zero when the
natSessionPrivateDstEPBindId object has a zero
value and natSessionPrivateDstEPBindMode is set to
addressPortBind(2). In such a case, the NAT session
lookup will match any port number to this field.
The value of this object must be zero when the object
is not a representative field (SrcPort, DstPort, or
ICMP identifier) of the session tuple in either the
public realm or the private realm."
::= { natSessionEntry 14 }
natSessionPublicAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object specifies the address type used for
natSessionPublicSrcAddr and natSessionPublicDstAddr."
::= { natSessionEntry 15 }
natSessionPublicSrcAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The source IP address of the session endpoint that
lies in the public network.
The value of this object must be zero when the
natSessionPrivateSrcEPBindId object has a zero value.
In such a scenario, the NAT session lookup will match
any IP address to this field.
The type of this address is determined by the value of
the natSessionPublicAddrType object."
::= { natSessionEntry 16 }
natSessionPublicSrcPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"When the value of protocol is TCP or UDP, this object
represents the source port in the first packet of
session while in public-realm. On the other hand, when
protocol is ICMP, a NAT session is created only for
query/response type ICMP messages such as ICMP echo,
Timestamp, and Information request messages, and this
object represents the public-realm specific identifier
in the ICMP message, as defined in RFC 792 for ICMPv4
and in RFC 2463 for ICMPv6.
The value of this object must be zero when the
natSessionPrivateSrcEPBindId object has a zero value
and natSessionPrivateSrcEPBindMode is set to
addressPortBind(2). In such a scenario, the NAT
session lookup will match any port number to this
field.
The value of this object must be zero when the object
is not a representative field (SrcPort, DstPort or
ICMP identifier) of the session tuple in either the
public realm or the private realm."
::= { natSessionEntry 17 }
natSessionPublicDstAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The destination IP address of the session endpoint that
lies in the public network.
The value of this object must be non-zero when the
natSessionPrivateDstEPBindId object has a non-zero
value. If the value of this object and the
corresponding natSessionPrivateDstEPBindId object value
is zero, then the NAT session lookup will match any IP
address to this field.
The type of this address is determined by the value of
the natSessionPublicAddrType object."
::= { natSessionEntry 18 }
natSessionPublicDstPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"When the value of protocol is TCP or UDP, this object
represents the destination port in the first packet of
session while in public-realm. On the other hand, when
the protocol is ICMP, this object is not relevant for
translation and should be zero.
The value of this object must be zero when the
natSessionPrivateDstEPBindId object has a zero value
and natSessionPrivateDstEPBindMode is
addressPortBind(2). In such a scenario, the NAT
session lookup will match any port number to this
field.
The value of this object must be zero when the object
is not a representative field (SrcPort, DstPort, or
ICMP identifier) of the session tuple in either the
public realm or the private realm."
::= { natSessionEntry 19 }
natSessionMaxIdleTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The max time for which this session can be idle
without detecting a packet."
::= { natSessionEntry 20 }
natSessionCurrentIdleTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The time since a packet belonging to this session was
last detected."
::= { natSessionEntry 21 }
natSessionInTranslates OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of inbound packets that were translated for
this session.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times, as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natSessionEntry 22 }
natSessionOutTranslates OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of outbound packets that were translated for
this session.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times, as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natSessionEntry 23 }
--
-- The Protocol table
--
natProtocolTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatProtocolEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The (conceptual) table containing per protocol NAT
statistics."
::= { natMIBObjects 10 }
natProtocolEntry OBJECT-TYPE
SYNTAX NatProtocolEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"An entry (conceptual row) containing NAT statistics
pertaining to a particular protocol."
INDEX { natProtocol }
::= { natProtocolTable 1 }
NatProtocolEntry ::= SEQUENCE {
natProtocol NatProtocolType,
natProtocolInTranslates Counter64,
natProtocolOutTranslates Counter64,
natProtocolDiscards Counter64
}
natProtocol OBJECT-TYPE
SYNTAX NatProtocolType
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This object represents the protocol pertaining to which
parameters are reported."
::= { natProtocolEntry 1 }
natProtocolInTranslates OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of inbound packets pertaining to the protocol
identified by natProtocol that underwent NAT.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times, as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natProtocolEntry 2 }
natProtocolOutTranslates OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of outbound packets pertaining to the
protocol identified by natProtocol that underwent NAT.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times, as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natProtocolEntry 3 }
natProtocolDiscards OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of packets pertaining to the protocol
identified by natProtocol that had to be
rejected/dropped due to lack of resources. These
rejections could be due to session timeout, resource
unavailability, lack of address space, etc.
Discontinuities in the value of this counter can occur
at reinitialization of the management system and at
other times, as indicated by the value of
ifCounterDiscontinuityTime on the relevant interface."
::= { natProtocolEntry 4 }
--
-- Notifications section
--
natMIBNotifications OBJECT IDENTIFIER ::= { natMIB 0 }
--
-- Notifications
--
natPacketDiscard NOTIFICATION-TYPE
OBJECTS { ifIndex }
STATUS deprecated
DESCRIPTION
"This notification is generated when IP packets are
discarded by the NAT function; e.g., due to lack of
mapping space when NAT is out of addresses or ports.
Note that the generation of natPacketDiscard
notifications is throttled by the agent, as specified
by the 'natNotifThrottlingInterval' object."
::= { natMIBNotifications 1 }
--
-- Conformance information.
--
natMIBConformance OBJECT IDENTIFIER ::= { natMIB 2 }
natMIBGroups OBJECT IDENTIFIER ::= { natMIBConformance 1 }
natMIBCompliances OBJECT IDENTIFIER ::= { natMIBConformance 2 }
--
-- Units of conformance
--
natConfigGroup OBJECT-GROUP
OBJECTS { natInterfaceRealm,
natInterfaceServiceType,
natInterfaceStorageType,
natInterfaceRowStatus,
natAddrMapName,
natAddrMapEntryType,
natAddrMapTranslationEntity,
natAddrMapLocalAddrType,
natAddrMapLocalAddrFrom,
natAddrMapLocalAddrTo,
natAddrMapLocalPortFrom,
natAddrMapLocalPortTo,
natAddrMapGlobalAddrType,
natAddrMapGlobalAddrFrom,
natAddrMapGlobalAddrTo,
natAddrMapGlobalPortFrom,
natAddrMapGlobalPortTo,
natAddrMapProtocol,
natAddrMapStorageType,
natAddrMapRowStatus,
natBindDefIdleTimeout,
natUdpDefIdleTimeout,
natIcmpDefIdleTimeout,
natOtherDefIdleTimeout,
natTcpDefIdleTimeout,
natTcpDefNegTimeout,
natNotifThrottlingInterval }
STATUS deprecated
DESCRIPTION
"A collection of configuration-related information
required to support management of devices supporting
NAT."
::= { natMIBGroups 1 }
natTranslationGroup OBJECT-GROUP
OBJECTS { natAddrBindNumberOfEntries,
natAddrBindGlobalAddrType,
natAddrBindGlobalAddr,
natAddrBindId,
natAddrBindTranslationEntity,
natAddrBindType,
natAddrBindMapIndex,
natAddrBindSessions,
natAddrBindMaxIdleTime,
natAddrBindCurrentIdleTime,
natAddrBindInTranslates,
natAddrBindOutTranslates,
natAddrPortBindNumberOfEntries,
natAddrPortBindGlobalAddrType,
natAddrPortBindGlobalAddr,
natAddrPortBindGlobalPort,
natAddrPortBindId,
natAddrPortBindTranslationEntity,
natAddrPortBindType,
natAddrPortBindMapIndex,
natAddrPortBindSessions,
natAddrPortBindMaxIdleTime,
natAddrPortBindCurrentIdleTime,
natAddrPortBindInTranslates,
natAddrPortBindOutTranslates,
natSessionPrivateSrcEPBindId,
natSessionPrivateSrcEPBindMode,
natSessionPrivateDstEPBindId,
natSessionPrivateDstEPBindMode,
natSessionDirection,
natSessionUpTime,
natSessionAddrMapIndex,
natSessionProtocolType,
natSessionPrivateAddrType,
natSessionPrivateSrcAddr,
natSessionPrivateSrcPort,
natSessionPrivateDstAddr,
natSessionPrivateDstPort,
natSessionPublicAddrType,
natSessionPublicSrcAddr,
natSessionPublicSrcPort,
natSessionPublicDstAddr,
natSessionPublicDstPort,
natSessionMaxIdleTime,
natSessionCurrentIdleTime,
natSessionInTranslates,
natSessionOutTranslates }
STATUS deprecated
DESCRIPTION
"A collection of BIND-related objects required to support
management of devices supporting NAT."
::= { natMIBGroups 2 }
natStatsInterfaceGroup OBJECT-GROUP
OBJECTS { natInterfaceInTranslates,
natInterfaceOutTranslates,
natInterfaceDiscards }
STATUS deprecated
DESCRIPTION
"A collection of NAT statistics associated with the
interface on which NAT is configured, to aid
troubleshooting/monitoring of the NAT operation."
::= { natMIBGroups 3 }
natStatsProtocolGroup OBJECT-GROUP
OBJECTS { natProtocolInTranslates,
natProtocolOutTranslates,
natProtocolDiscards }
STATUS deprecated
DESCRIPTION
"A collection of protocol specific NAT statistics,
to aid troubleshooting/monitoring of NAT operation."
::= { natMIBGroups 4 }
natStatsAddrMapGroup OBJECT-GROUP
OBJECTS { natAddrMapInTranslates,
natAddrMapOutTranslates,
natAddrMapDiscards,
natAddrMapAddrUsed }
STATUS deprecated
DESCRIPTION
"A collection of address map specific NAT statistics,
to aid troubleshooting/monitoring of NAT operation."
::= { natMIBGroups 5 }
natMIBNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS { natPacketDiscard }
STATUS deprecated
DESCRIPTION
"A collection of notifications generated by
devices supporting this MIB."
::= { natMIBGroups 6 }
--
-- Compliance statements
--
natMIBFullCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"When this MIB is implemented with support for
read-create, then such an implementation can claim
full compliance. Such devices can then be both
monitored and configured with this MIB.
The following index objects cannot be added as OBJECT
clauses but nevertheless have the compliance
requirements:
"
-- OBJECT natAddrBindLocalAddrType
-- SYNTAX InetAddressType { ipv4(1), ipv6(2) }
-- DESCRIPTION
-- "An implementation is required to support
-- global IPv4 and/or IPv6 addresses, depending
-- on its support for IPv4 and IPv6."
-- OBJECT natAddrBindLocalAddr
-- SYNTAX InetAddress (SIZE(4|16))
-- DESCRIPTION
-- "An implementation is required to support
-- global IPv4 and/or IPv6 addresses, depending
-- on its support for IPv4 and IPv6."
-- OBJECT natAddrPortBindLocalAddrType
-- SYNTAX InetAddressType { ipv4(1), ipv6(2) }
-- DESCRIPTION
-- "An implementation is required to support
-- global IPv4 and/or IPv6 addresses, depending
-- on its support for IPv4 and IPv6."
-- OBJECT natAddrPortBindLocalAddr
-- SYNTAX InetAddress (SIZE(4|16))
-- DESCRIPTION
-- "An implementation is required to support
-- global IPv4 and/or IPv6 addresses, depending
-- on its support for IPv4 and IPv6."
MODULE IF-MIB -- The interfaces MIB, RFC2863
MANDATORY-GROUPS {
ifCounterDiscontinuityGroup
}
MODULE -- this module
MANDATORY-GROUPS { natConfigGroup, natTranslationGroup,
natStatsInterfaceGroup }
GROUP natStatsProtocolGroup
DESCRIPTION
"This group is optional."
GROUP natStatsAddrMapGroup
DESCRIPTION
"This group is optional."
GROUP natMIBNotificationGroup
DESCRIPTION
"This group is optional."
OBJECT natAddrMapLocalAddrType
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natAddrMapLocalAddrFrom
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natAddrMapLocalAddrTo
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natAddrMapGlobalAddrType
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natAddrMapGlobalAddrFrom
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natAddrMapGlobalAddrTo
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natAddrBindGlobalAddrType
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natAddrBindGlobalAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natAddrPortBindGlobalAddrType
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natAddrPortBindGlobalAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natSessionPrivateAddrType
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natSessionPrivateSrcAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natSessionPrivateDstAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natSessionPublicAddrType
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natSessionPublicSrcAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
OBJECT natSessionPublicDstAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support
for IPv4 and IPv6."
::= { natMIBCompliances 1 }
natMIBReadOnlyCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"When this MIB is implemented without support for
read-create (i.e., in read-only mode), then such an
implementation can claim read-only compliance.
Such a device can then be monitored but cannot be
configured with this MIB.
The following index objects cannot be added as OBJECT
clauses but nevertheless have the compliance
requirements:
"
-- OBJECT natAddrBindLocalAddrType
-- SYNTAX InetAddressType { ipv4(1), ipv6(2) }
-- DESCRIPTION
-- "An implementation is required to support
-- global IPv4 and/or IPv6 addresses, depending
-- on its support for IPv4 and IPv6."
-- OBJECT natAddrBindLocalAddr
-- SYNTAX InetAddress (SIZE(4|16))
-- DESCRIPTION
-- "An implementation is required to support
-- global IPv4 and/or IPv6 addresses, depending
-- on its support for IPv4 and IPv6."
-- OBJECT natAddrPortBindLocalAddrType
-- SYNTAX InetAddressType { ipv4(1), ipv6(2) }
-- DESCRIPTION
-- "An implementation is required to support
-- global IPv4 and/or IPv6 addresses, depending
-- on its support for IPv4 and IPv6."
-- OBJECT natAddrPortBindLocalAddr
-- SYNTAX InetAddress (SIZE(4|16))
-- DESCRIPTION
-- "An implementation is required to support
-- global IPv4 and/or IPv6 addresses, depending
-- on its support for IPv4 and IPv6."
MODULE IF-MIB -- The interfaces MIB, RFC2863
MANDATORY-GROUPS {
ifCounterDiscontinuityGroup
}
MODULE -- this module
MANDATORY-GROUPS { natConfigGroup, natTranslationGroup,
natStatsInterfaceGroup }
GROUP natStatsProtocolGroup
DESCRIPTION
"This group is optional."
GROUP natStatsAddrMapGroup
DESCRIPTION
"This group is optional."
GROUP natMIBNotificationGroup
DESCRIPTION
"This group is optional."
OBJECT natInterfaceRowStatus
SYNTAX RowStatus { active(1) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required, and active is the only
status that needs to be supported."
OBJECT natAddrMapLocalAddrType
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. An implementation is
required to support global IPv4 and/or IPv6 addresses,
depending on its support for IPv4 and IPv6."
OBJECT natAddrMapLocalAddrFrom
SYNTAX InetAddress (SIZE(4|16))
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. An implementation is
required to support global IPv4 and/or IPv6 addresses,
depending on its support for IPv4 and IPv6."
OBJECT natAddrMapLocalAddrTo
SYNTAX InetAddress (SIZE(4|16))
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. An implementation is
required to support global IPv4 and/or IPv6 addresses,
depending on its support for IPv4 and IPv6."
OBJECT natAddrMapGlobalAddrType
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. An implementation is
required to support global IPv4 and/or IPv6 addresses,
depending on its support for IPv4 and IPv6."
OBJECT natAddrMapGlobalAddrFrom
SYNTAX InetAddress (SIZE(4|16))
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. An implementation is
required to support global IPv4 and/or IPv6 addresses,
depending on its support for IPv4 and IPv6."
OBJECT natAddrMapGlobalAddrTo
SYNTAX InetAddress (SIZE(4|16))
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. An implementation is
required to support global IPv4 and/or IPv6 addresses,
depending on its support for IPv4 and IPv6."
OBJECT natAddrMapRowStatus
SYNTAX RowStatus { active(1) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required, and active is the only
status that needs to be supported."
OBJECT natAddrBindGlobalAddrType
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support for
IPv4 and IPv6."
OBJECT natAddrBindGlobalAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support for
IPv4 and IPv6."
OBJECT natAddrPortBindGlobalAddrType
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support for
IPv4 and IPv6."
OBJECT natAddrPortBindGlobalAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support for
IPv4 and IPv6."
OBJECT natSessionPrivateAddrType
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support for
IPv4 and IPv6."
OBJECT natSessionPrivateSrcAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support for
IPv4 and IPv6."
OBJECT natSessionPrivateDstAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support for
IPv4 and IPv6."
OBJECT natSessionPublicAddrType
SYNTAX InetAddressType { ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support for
IPv4 and IPv6."
OBJECT natSessionPublicSrcAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support for
IPv4 and IPv6."
OBJECT natSessionPublicDstAddr
SYNTAX InetAddress (SIZE(4|16))
DESCRIPTION
"An implementation is required to support global IPv4
and/or IPv6 addresses, depending on its support for
IPv4 and IPv6."
::= { natMIBCompliances 2 }
--===================================================================
-- END OF DEPRECATED OBJECTS. CURRENT OBJECTS FOLLOW.
-- textual conventions
ProtocolNumber ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"A transport protocol number, from the 'protocol-numbers'
IANA registry."
SYNTAX Unsigned32 (0..255)
NatPoolId ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"A unique ID that is assigned to each pool."
SYNTAX Unsigned32 (1..4294967295)
NatBehaviorType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Behavior type as described in [RFC4787] sections 4.1 and 5."
SYNTAX INTEGER {
endpointIndependent (0),
addressDependent (1),
addressAndPortDependent (2)
}
NatPoolingType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Pooling type as described in [RFC4787] sections 4.1."
SYNTAX INTEGER {
arbitrary (0),
paired (1)
}
VlanIndexOrZero ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"A value used to index per-VLAN tables: a value of 4095 is
not permitted. A value of 0 indicates no index is present.
If the value is between 1 and 4094 inclusive, it represents
an IEEE 802.1Q VLAN-ID with global scope within a given
bridged domain (see VlanId textual convention in
[RFC4363]). If the value is greater than 4095, then it
represents a VLAN with scope local to the particular agent,
i.e., one without a global VLAN-ID assigned to it. Such
VLANs are outside the scope of IEEE 802.1Q, but it is
convenient to be able to manage them in the same way using
this MIB."
SYNTAX Unsigned32
SubscriberIndex ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"A unique ID that is assigned to each subscriber."
SYNTAX Unsigned32 (1..4294967295)
SubscriberIdentifierType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Type of additional classifying information used by the NAT
to identify the subscriber from an incoming packet, when
the packet source address is not sufficient to do so
unambiguously.
null(0)
No additional information is needed.
interfaces(1)
A set of one or more ingress interface indexes specified
by the [RFC2863] InterfaceIndex textual convention.
vlan(2)
An ingress VLAN index using the VlanIndexOrZero textual
convention, which is the [RFC4363] VlanIndex textual
convention modified for local use in this MIB.
vpn(3)
An ingress layer 3 VPN identifier using the [RFC4265]
VPNIdOrZero textual convention.
ipencaps(4)
Incoming source address of an encapsulating IPv4 or IPv6
tunnel (e.g., IPv6 as used in DS-Lite, [RFC6333]) as
defined by the InetAddressType and InetAddress textual
conventions.
other(5)
The implementation supports other classifiers and/or
combinations of classifier types. In the latter case the
implementation MUST specify the semantics of the
combination ('OR' or 'AND')."
SYNTAX INTEGER {
null(0),
interfaces(1),
vlan(2),
vpn(3),
ipencaps(4),
other(5)
}
SubsInterfaceIdRowIndex ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"A unique ID that is assigned to each row in the
natSubsInterfaceIdentifierTable."
SYNTAX Unsigned32 (1..4294967295)
-- notifications
natNotifPoolWatermarkLow NOTIFICATION-TYPE
OBJECTS { natPoolWatermarkLow }
STATUS current
DESCRIPTION
"This notification is generated when a pool's usage
percentage becomes lower than or equal to the specified
threshold. The threshold is specified by the
natPoolWatermarkLow object"
::= { natMIBNotifications 2 }
natNotifPoolWatermarkHigh NOTIFICATION-TYPE
OBJECTS { natPoolWatermarkHigh }
STATUS current
DESCRIPTION
"This notification is generated when a pool's usage
percentage becomes greater than or equal to the specified
threshold. The threshold is specified by the
natPoolWatermarkHigh object"
::= { natMIBNotifications 3 }
natNotifMappings NOTIFICATION-TYPE
OBJECTS { natMappingCreations, natMappingRemovals }
STATUS current
DESCRIPTION
"This notification is generated when the number of active
mappings exceeds the value of natMappingsNotifyThreshold."
::= { natMIBNotifications 4 }
natNotifAddrMappings NOTIFICATION-TYPE
OBJECTS { natAddressMappingCreations, natAddressMappingRemovals }
STATUS current
DESCRIPTION
"This notification is generated when the number of active
address mappings exceeds the value of
natAddrMapNotifyThreshold."
::= { natMIBNotifications 5 }
natNotifSubscriberMappings NOTIFICATION-TYPE
OBJECTS { natSubscriberMappingCreations,
natSubscriberMappingRemovals }
STATUS current
DESCRIPTION
"This notification is generated when the number of active
mappings exceeds the value of natSubscriberMapNotifyThresh,
unless natSubscriberMapNotifyThresh is zero.."
::= { natMIBNotifications 6 }
-- instance table
natInstanceTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatInstanceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of NAT instances."
::= { natMIBObjects 11 }
natInstanceEntry OBJECT-TYPE
SYNTAX NatInstanceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Objects related to a single NAT instance."
INDEX { natInstanceIndex }
::= { natInstanceTable 1 }
NatInstanceEntry ::=
SEQUENCE {
natInstanceIndex Unsigned32,
natInstanceAlias DisplayString
}
natInstanceIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"NAT instance index. Semantics of this number are
implementation-specific. This object is used as an index for
many tables defined below."
::= { natInstanceEntry 1 }
natInstanceAlias OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is an 'alias' name for the NAT instance as
specified by a network manager, and provides a non-volatile
'handle' for the instance.
On the first instantiation of a NAT instance, the value of
natInstanceAlias associated with that instance is the
zero-length string. As and when a value is written into an
instance of natInstanceAlias through a network management
set operation, then the agent must retain the supplied value
in this obejct instance associated with the same interface
for as long as that NAT instance remains instantiated,
including across all re-initializations/reboots of the
network management system, including those which result in a
change of the interface's natInstanceIndex value.
An example of the value which a network manager might store
in this object for a NAT instance is the name/identifier of
the interface that brings in internal traffic for this NAT
instance or the name of the VRF for internal traffic.
An agent may choose to provide read-only access if the agent
itself assigns an identifier for the NAT instance. An agent
which supports write access to this object is required to
keep the value in non-valite storage, but it may limit the
length of new values depending on how much storage is
already occupied by the current values for other
NAT instances."
::= { natInstanceEntry 2 }
-- counters
natCounters OBJECT IDENTIFIER ::= { natMIBObjects 12 }
natCountersTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatCountersEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of counters of a NAT instance. The counters are global
across L4 protocols."
::= { natCounters 1 }
natCountersEntry OBJECT-TYPE
SYNTAX NatCountersEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Counters related to a single NAT instance."
INDEX { natInstanceIndex }
::= { natCountersTable 1 }
NatCountersEntry ::=
SEQUENCE {
natTranslations Counter64,
natOutOfPortErrors Counter64,
natResourceErrors Counter64,
natQuotaDrops Counter64,
natMappingCreations Counter64,
natMappingRemovals Counter64,
natAddressMappingCreations Counter64,
natAddressMappingRemovals Counter64
}
natTranslations OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets translated."
::= { natCountersEntry 1 }
natOutOfPortErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets not translated because no external
port was available, excluding quota limitations."
::= { natCountersEntry 2 }
natResourceErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets not translated because of resource
constraints (excluding out-of-ports error and quota drops)."
::= { natCountersEntry 3 }
natQuotaDrops OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of incoming packets not translated because of
quota limitations. Quotas include absolute limits as well
as limits on rate of allocation."
::= { natCountersEntry 4 }
natMappingCreations OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of mapping creations. This includes static mappings."
::= { natCountersEntry 5 }
natMappingRemovals OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of mapping removals. This includes static mappings."
::= { natCountersEntry 6 }
natAddressMappingCreations OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of address mapping creations. This includes static
mappings."
::= { natCountersEntry 7 }
natAddressMappingRemovals OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of address mapping removals. This includes static
mappings.
The number of active mappings is equal to
natAddressMappingCreations - natAddressMappingRemovals."
::= { natCountersEntry 8 }
natL4ProtocolTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatL4ProtocolEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of protocols with per-protocol counters."
::= { natCounters 2 }
natL4ProtocolEntry OBJECT-TYPE
SYNTAX NatL4ProtocolEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Per-protocol counters."
INDEX { natInstanceIndex, natL4ProtocolNumber }
::= { natL4ProtocolTable 1 }
NatL4ProtocolEntry ::=
SEQUENCE {
natL4ProtocolNumber ProtocolNumber,
natL4ProtocolTranslations Counter64,
natL4ProtocolOutOfPortErrors Counter64,
natL4ProtocolResourceErrors Counter64,
natL4ProtocolQuotaDrops Counter64,
natL4ProtocolMappingCreations Counter64,
natL4ProtocolMappingRemovals Counter64
}
natL4ProtocolNumber OBJECT-TYPE
SYNTAX ProtocolNumber
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Counters in this conceptual row apply to packets using the
transport protocol identified by this object's value."
::= { natL4ProtocolEntry 1 }
natL4ProtocolTranslations OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets translated."
::= { natL4ProtocolEntry 2 }
natL4ProtocolOutOfPortErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets not translated because no external
port was available."
::= { natL4ProtocolEntry 3 }
natL4ProtocolResourceErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets not translated because of resource
constraints (excluding out-of-ports errors and quota
drops)."
::= { natL4ProtocolEntry 4 }
natL4ProtocolQuotaDrops OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of incoming packets not translated because of
exceeded quotas. Quotas include absolute limits as well as
limits on rate of allocation."
::= { natL4ProtocolEntry 5 }
natL4ProtocolMappingCreations OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of mapping creations. This includes static mappings."
::= { natL4ProtocolEntry 6 }
natL4ProtocolMappingRemovals OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of mapping removals. This includes static mappings.
The number of active mappings is equal to
natL4ProtocolMappingCreations -
natL4ProtocolMappingRemovals."
::= { natL4ProtocolEntry 7 }
-- limits
natLimitsTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatLimitsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of limits for a NAT instance."
::= { natMIBObjects 13 }
natLimitsEntry OBJECT-TYPE
SYNTAX NatLimitsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Limit related to a single NAT instance."
INDEX { natInstanceIndex }
::= { natLimitsTable 1 }
NatLimitsEntry ::=
SEQUENCE {
natLimitMappings Unsigned32,
natMappingsNotifyThreshold Unsigned32,
natLimitAddressMappings Unsigned32,
natAddrMapNotifyThreshold Unsigned32,
natLimitFragments Unsigned32,
natLimitSubscribers Unsigned32
}
natLimitMappings OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Global limit on the total number of mappings. Zero means
unlimited."
::= { natLimitsEntry 1 }
natMappingsNotifyThreshold OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"See natNotifMappings."
::= { natLimitsEntry 2 }
natLimitAddressMappings OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Global limit on the total number of internal-to-external
address mappings. Zero means unlimited.
This limit is only applicable to NATs that have an 'IP
address pooling' behavior of 'Paired' [RFC4787]."
::= { natLimitsEntry 3 }
natAddrMapNotifyThreshold OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"See natNotifAddrMappings."
::= { natLimitsEntry 4 }
natLimitFragments OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Global limit on the total number of fragments pending
reassembly. Zero means unlimited.
This limit is only applicable to NATs having 'Receive
Fragments Out of Order' behavior [RFC4787]."
::= { natLimitsEntry 5 }
natLimitSubscribers OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Global limit on the number of subscribers with active
mappings. Zero means unlimited."
::= { natLimitsEntry 6 }
-- pools
natPoolObjects OBJECT IDENTIFIER ::= { natMIBObjects 14 }
natPoolTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatPoolEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of pools."
::= { natPoolObjects 1 }
natPoolEntry OBJECT-TYPE
SYNTAX NatPoolEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry in the table of pools."
INDEX { natInstanceIndex, natPoolIndex }
::= { natPoolTable 1 }
NatPoolEntry ::=
SEQUENCE {
natPoolIndex NatPoolId,
natPoolRealm SnmpAdminString,
natPoolWatermarkLow Integer32,
natPoolWatermarkHigh Integer32,
natPoolPortMin InetPortNumber,
natPoolPortMax InetPortNumber
}
natPoolIndex OBJECT-TYPE
SYNTAX NatPoolId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of an address pool."
::= { natPoolEntry 1 }
natPoolRealm OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Realm to which this pool's addresses belong."
::= { natPoolEntry 2 }
natPoolWatermarkLow OBJECT-TYPE
SYNTAX Integer32 (-1|0..100)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Low watermark on a pool's usage, in percentage of the total
number of ports available. If set to -1, the watermark is
disabled. Otherwise when the usage percentage becomes lower
than or equal to natPoolWatermarkLow, a notification is
sent. The NAT may also start behaving in low usage mode
(this is implementation-defined).
The pool's current usage percentage can be computed by
summing (natPoolRangeAllocations -
natPoolRangeDeallocations) over all address ranges
belonging to this pool, then dividing by the total number of
IP addresses in this pool and by the size of the port range
in this pool (natPoolPortMax - natPoolPortMin + 1)."
::= { natPoolEntry 3 }
natPoolWatermarkHigh OBJECT-TYPE
SYNTAX Integer32 (-1|0..100)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"High watermark on a pool's usage, in percentage of the total
number of ports available. If set to -1, the watermark is
disabled. Otherwise, when the usage percentage becomes
higher than or equal to natPoolWatermarkHigh, a notification
is sent. The NAT may also start behaving in high usage mode
(this is implementation-defined)."
::= { natPoolEntry 4 }
natPoolPortMin OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimal port number to be allocated in this pool."
::= { natPoolEntry 5 }
natPoolPortMax OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximal port number to be allocated in this pool."
::= { natPoolEntry 6 }
natPoolRangeTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatPoolRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains address ranges used by pool entries."
::= { natPoolObjects 2 }
natPoolRangeEntry OBJECT-TYPE
SYNTAX NatPoolRangeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"NAT pool address range."
INDEX { natInstanceIndex, natPoolRangePoolIndex }
::= { natPoolRangeTable 1 }
NatPoolRangeEntry ::=
SEQUENCE {
natPoolRangePoolIndex NatPoolId,
natPoolRangeType InetAddressType,
natPoolRangeBegin InetAddress,
natPoolRangeEnd InetAddress,
natPoolRangeAllocations Counter64,
natPoolRangeDeallocations Counter64
}
natPoolRangePoolIndex OBJECT-TYPE
SYNTAX NatPoolId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of the address pool to which this address range
belongs. See natPoolIndex."
::= { natPoolRangeEntry 1 }
natPoolRangeType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type of natPoolRangeBegin and
natPoolRangeEnd."
::= { natPoolRangeEntry 2 }
natPoolRangeBegin OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Lowest address included in this range."
::= { natPoolRangeEntry 3 }
natPoolRangeEnd OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Highest address included in this range."
::= { natPoolRangeEntry 4 }
natPoolRangeAllocations OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ports that have been allocated on the addresses in
this range."
::= { natPoolRangeEntry 5 }
natPoolRangeDeallocations OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of ports that have been allocated and then
deallocated on the addresses in this range.
The number of ports currently allocated on the addresses in
this range can be computed by subtracting
natPoolRangeDeallocations from natPoolRangeAllocations."
::= { natPoolRangeEntry 6 }
-- indexed mapping tables
natMapObjects OBJECT IDENTIFIER ::= { natMIBObjects 15 }
natMapIntAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatMapIntAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of mappings from internal to external address.
This table is only applicable to NATs that have an 'IP
address pooling' behavior of 'Paired' [RFC4787]."
::= { natMapObjects 1 }
natMapIntAddrEntry OBJECT-TYPE
SYNTAX NatMapIntAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Mapping from internal to external address."
INDEX { natInstanceIndex,
natMapIntAddrIntRealm,
natMapIntAddrIntType,
natMapIntAddrInt }
::= { natMapIntAddrTable 1 }
NatMapIntAddrEntry ::=
SEQUENCE {
natMapIntAddrIntRealm SnmpAdminString,
natMapIntAddrExtRealm SnmpAdminString,
natMapIntAddrIntType InetAddressType,
natMapIntAddrInt InetAddress,
natMapIntAddrExtType InetAddressType,
natMapIntAddrExt InetAddress,
natMapIntAddrSubsIndex Unsigned32
}
natMapIntAddrIntRealm OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Realm to which natMapIntAddrInt belongs."
::= { natMapIntAddrEntry 1 }
natMapIntAddrExtRealm OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Realm to which natMapIntAddrExt belongs."
::= { natMapIntAddrEntry 2 }
natMapIntAddrIntType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address type for natMapIntAddrInt."
::= { natMapIntAddrEntry 3 }
natMapIntAddrInt OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Internal address."
::= { natMapIntAddrEntry 4 }
natMapIntAddrExtType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Address type for natMapIntAddrExt."
::= { natMapIntAddrEntry 5 }
natMapIntAddrExt OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"External address."
::= { natMapIntAddrEntry 6 }
natMapIntAddrSubsIndex OBJECT-TYPE
SYNTAX Unsigned32 (0|1..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Subscriber to which this address mapping applies, or zero if
it applies to all subscribers."
::= { natMapIntAddrEntry 7 }
natMappingTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of mappings indexed by external 3-tuple."
::= { natMapObjects 2 }
natMappingEntry OBJECT-TYPE
SYNTAX NatMappingEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single NAT mapping."
INDEX { natInstanceIndex,
natMappingProto,
natMappingExtRealm,
natMappingExtAddressType,
natMappingExtAddress,
natMappingExtPort }
::= { natMappingTable 1 }
NatMappingEntry ::=
SEQUENCE {
natMappingProto ProtocolNumber,
natMappingExtRealm SnmpAdminString,
natMappingExtAddressType InetAddressType,
natMappingExtAddress InetAddress,
natMappingExtPort InetPortNumber,
natMappingIntRealm SnmpAdminString,
natMappingIntAddressType InetAddressType,
natMappingIntAddress InetAddress,
natMappingIntPort InetPortNumber,
natMappingPool Unsigned32,
natMappingMapBehavior NatBehaviorType,
natMappingFilterBehavior NatBehaviorType,
natMappingAddressPooling NatPoolingType,
natMappingSubsIndex SubscriberIndex
}
natMappingProto OBJECT-TYPE
SYNTAX ProtocolNumber
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The mapping's transport protocol number."
::= { natMappingEntry 1 }
natMappingExtRealm OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The realm to which natMappingExtAddress belongs."
::= { natMappingEntry 2 }
natMappingExtAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Type of the mapping's external address."
::= { natMappingEntry 3 }
natMappingExtAddress OBJECT-TYPE
SYNTAX InetAddress (SIZE (4|16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The mapping's external address. If this is the undefined
address, all external addresses are mapped to the internal
address."
::= { natMappingEntry 4 }
natMappingExtPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The mapping's external port number. If this is zero, all
external ports are mapped to the internal port."
::= { natMappingEntry 5 }
natMappingIntRealm OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The realm to which natMappingIntAddress belongs."
::= { natMappingEntry 6 }
natMappingIntAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Type of the mapping's internal address."
::= { natMappingEntry 7 }
natMappingIntAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The mapping's internal address. If this is the undefined
address, addresses are not translated."
::= { natMappingEntry 8 }
natMappingIntPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The mapping's internal port number. If this is zero, ports
are not translated."
::= { natMappingEntry 9 }
natMappingPool OBJECT-TYPE
SYNTAX Unsigned32 (0|1..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Index of the pool that contains this mapping's external
address and port. If zero, no pool is associated with this
mapping."
::= { natMappingEntry 10 }
natMappingMapBehavior OBJECT-TYPE
SYNTAX NatBehaviorType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Mapping behavior as described in [RFC4787] section 4.1."
::= { natMappingEntry 11 }
natMappingFilterBehavior OBJECT-TYPE
SYNTAX NatBehaviorType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Filtering behavior as described in [RFC4787] section 5."
::= { natMappingEntry 12 }
natMappingAddressPooling OBJECT-TYPE
SYNTAX NatPoolingType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Type of address pooling behavior that was used to create
this mapping."
::= { natMappingEntry 13 }
natMappingSubsIndex OBJECT-TYPE
SYNTAX SubscriberIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Subscriber using this mapping."
::= { natMappingEntry 14 }
-- subscribers
natSubscribers OBJECT IDENTIFIER ::= { natMIBObjects 16 }
natSubscribersTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatSubscribersEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of CGN subscribers."
::= { natSubscribers 1 }
natSubscribersEntry OBJECT-TYPE
SYNTAX NatSubscribersEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry describes a single CGN subscriber or a host
served by a managed enterprise NAT."
INDEX { natInstanceIndex,
natSubscriberIndex }
::= { natSubscribersTable 1 }
NatSubscribersEntry ::=
SEQUENCE {
natSubscriberIndex SubscriberIndex,
natSubscriberIdentifierType SubscriberIdentifierType,
natSubscriberIntPrefixType InetAddressType,
natSubscriberIntPrefix InetAddress,
natSubscriberIntPrefixLength InetAddressPrefixLength,
natSubscriberRealm SnmpAdminString,
natSubscriberTranslations Counter64,
natSubscriberOutOfPortErrors Counter64,
natSubscriberResourceErrors Counter64,
natSubscriberQuotaDrops Counter64,
natSubscriberMappingCreations Counter64,
natSubscriberMappingRemovals Counter64,
natSubscriberLimitMappings Unsigned32,
natSubscriberMapNotifyThresh Unsigned32,
natSubscriberVlanIdentifier VlanIndexOrZero,
natSubscriberVpnIdentifier VPNIdOrZero,
natSubscriberIPEncapsIdType InetAddressType,
natSubscriberIPEncapsIdAddr InetAddress
}
natSubscriberIndex OBJECT-TYPE
SYNTAX SubscriberIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of the subscriber or host."
::= { natSubscribersEntry 1 }
natSubscriberIdentifierType OBJECT-TYPE
SYNTAX SubscriberIdentifierType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Type of additional information needed to identify the
subscriber or host from incoming packets, when the packet
source address does not do so unambiguously.
The implementation MUST ensure that the type and the
identifier value provided are synchronized, as follows.
Unused identifier values MUST be zero or equivalent.
Type Identifier object
null(0) None.
interfaces(1) natSubsInterfaceIdentifierTable
vlan(2) natSubscriberVlanIdentifier
vpn(3) natSubscriberVpnIdentifier
ipencaps(4) natSubscriberIPEncapsIdType and
natSubscriberIPEncapsIdAddr
other(5) As specified by the implementation"
::= { natSubscribersEntry 2 }
natSubscriberIntPrefixType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Subscriber's internal prefix type."
::= { natSubscribersEntry 3 }
natSubscriberIntPrefix OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Prefix assigned to a subscriber's CPE."
::= { natSubscribersEntry 4 }
natSubscriberIntPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Length of the prefix assigned to a subscriber's CPE, in
bits. In case a single address is assigned, this will be 32
for IPv4 and 128 for IPv6."
::= { natSubscribersEntry 5 }
natSubscriberRealm OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The realm to which this subscriber belongs."
::= { natSubscribersEntry 6 }
natSubscriberTranslations OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of translated packets received from or sent to
this subscriber."
::= { natSubscribersEntry 7 }
natSubscriberOutOfPortErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets received from this subscriber not
translated because no external port was available, excluding
quota limitations."
::= { natSubscribersEntry 8 }
natSubscriberResourceErrors OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of packets received from this subscriber not
translated because of resource constraints (excluding
out-of-port errors and quota drops)."
::= { natSubscribersEntry 9 }
natSubscriberQuotaDrops OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of incoming packets received from or destined to
this subscriber not translated because of quota limitations.
Quotas include absolute limits as well as limits on the rate
of allocation."
::= { natSubscribersEntry 10 }
natSubscriberMappingCreations OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of mappings created by or for this subscriber."
::= { natSubscribersEntry 11 }
natSubscriberMappingRemovals OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of mappings removed by or for this subscriber."
::= { natSubscribersEntry 12 }
natSubscriberLimitMappings OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Limit on the number of active mappings created by or for
this subscriber. Zero means unlimited."
::= { natSubscribersEntry 13 }
natSubscriberMapNotifyThresh OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"See natNotifSubscriberMappings."
::= { natSubscribersEntry 14 }
natSubscriberVlanIdentifier OBJECT-TYPE
SYNTAX VlanIndexOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When non-zero, VLAN index used to identify subscriber in
combination with packet source address."
::= { natSubscribersEntry 15 }
natSubscriberVpnIdentifier OBJECT-TYPE
SYNTAX VPNIdOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When non-zero, VPN identifier used to identify subscriber
in combination with packet source address."
::= { natSubscribersEntry 16 }
natSubscriberIPEncapsIdType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When not unknown(0), type of address of encapsulating IP
ingress tunnel."
::= { natSubscribersEntry 17 }
natSubscriberIPEncapsIdAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Source address in outer header of packets incoming via IP
tunnel, used to identify subscriber in combination with
inner packet source address."
::= { natSubscribersEntry 18 }
natSubsInterfaceIdentifierTable OBJECT-TYPE
SYNTAX SEQUENCE OF NatSubsInterfaceIdentifierEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of interface indexes. If non-empty, used along with
packet source address to identify the subscriber sending
the packet. 'OR' semantics if multiple interface indexes
are present."
::= { natSubscribers 2 }
natSubsInterfaceIdentifierEntry OBJECT-TYPE
SYNTAX NatSubsInterfaceIdentifierEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry provides a single interface index."
INDEX { natInstanceIndex,
natSubsInterfaceIdSubsIndex,
natSubsInterfaceIdRowIndex }
::= { natSubsInterfaceIdentifierTable 1 }
NatSubsInterfaceIdentifierEntry ::=
SEQUENCE {
natSubsInterfaceIdSubsIndex SubscriberIndex,
natSubsInterfaceIdRowIndex SubsInterfaceIdRowIndex,
natSubsInterfaceIndex InterfaceIndex
}
natSubsInterfaceIdSubsIndex OBJECT-TYPE
SYNTAX SubscriberIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of the subscriber to which this conceptual table is
related."
::= { natSubsInterfaceIdentifierEntry 1 }
natSubsInterfaceIdRowIndex OBJECT-TYPE
SYNTAX SubsInterfaceIdRowIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Row index."
::= { natSubsInterfaceIdentifierEntry 2 }
natSubsInterfaceIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Interface index of an ingress interface through which
packets from this subscriber may flow."
::= { natSubsInterfaceIdentifierEntry 3 }
-- object groups
natGroupStatelessObjects OBJECT-GROUP
OBJECTS { natInstanceAlias,
natTranslations,
natResourceErrors,
natQuotaDrops,
natMappingCreations,
natMappingRemovals,
natL4ProtocolTranslations ,
natL4ProtocolResourceErrors,
natL4ProtocolQuotaDrops,
natL4ProtocolMappingCreations,
natL4ProtocolMappingRemovals,
natMappingIntRealm,
natMappingIntAddressType,
natMappingIntAddress,
natMappingIntPort,
natMappingPool,
natMappingMapBehavior,
natMappingFilterBehavior }
STATUS current
DESCRIPTION
"Basic counters, limits, and thresholds that do not require
stateful NAT. That is, they apply to both stateless and
stateful NATs.
For this MIB's purposes, stateless NATs are defined as NATs
that do not create mappings dynamically (either implicitly
or explicitly using, for instance, the Port Control
Protocol). Their mappings are created statically by the NAT
administrator."
::= { natMIBGroups 7 }
natGroupStatefulObjects OBJECT-GROUP
OBJECTS { natOutOfPortErrors,
natL4ProtocolOutOfPortErrors,
natLimitMappings,
natMappingsNotifyThreshold,
natPoolRealm,
natPoolWatermarkLow,
natPoolWatermarkHigh,
natPoolPortMin,
natPoolPortMax,
natPoolRangeType,
natPoolRangeBegin,
natPoolRangeEnd,
natPoolRangeAllocations,
natPoolRangeDeallocations,
natMappingAddressPooling }
STATUS current
DESCRIPTION
"Basic counters, limits, and thresholds that require stateful
NAT."
::= { natMIBGroups 8 }
natGroupAddrMapObjects OBJECT-GROUP
OBJECTS { natAddressMappingCreations,
natAddressMappingRemovals,
natLimitAddressMappings,
natAddrMapNotifyThreshold,
natMapIntAddrExtRealm,
natMapIntAddrExtType,
natMapIntAddrExt }
STATUS current
DESCRIPTION
"Objects that require 'Paired IP address pooling' behavior
[RFC4787]."
::= { natMIBGroups 9 }
natGroupFragmentObjects OBJECT-GROUP
OBJECTS { natLimitFragments }
STATUS current
DESCRIPTION
"Objects that require 'Receive Fragments Out of Order'
behavior [RFC4787]."
::= { natMIBGroups 10 }
natGroupBasicNotifications NOTIFICATION-GROUP
NOTIFICATIONS { natNotifPoolWatermarkLow,
natNotifPoolWatermarkHigh,
natNotifMappings }
STATUS current
DESCRIPTION
"Basic notifications."
::= { natMIBGroups 11 }
natGroupAddrMapNotifications NOTIFICATION-GROUP
NOTIFICATIONS { natNotifAddrMappings }
STATUS current
DESCRIPTION
"Notifications about address mappings."
::= { natMIBGroups 12 }
natGroupSubscriberObjects OBJECT-GROUP
OBJECTS { natMapIntAddrSubsIndex,
natMappingSubsIndex,
natSubscriberIdentifierType,
natSubscriberIntPrefixType,
natSubscriberIntPrefix,
natSubscriberIntPrefixLength,
natSubscriberRealm,
natSubscriberTranslations,
natSubscriberOutOfPortErrors,
natSubscriberResourceErrors,
natSubscriberQuotaDrops,
natSubscriberMappingCreations,
natSubscriberMappingRemovals,
natSubscriberLimitMappings,
natSubscriberVlanIdentifier,
natSubscriberVpnIdentifier,
natSubscriberIPEncapsIdType,
natSubscriberIPEncapsIdAddr,
natSubsInterfaceIndex,
natLimitSubscribers,
natSubscriberMapNotifyThresh }
STATUS current
DESCRIPTION
"Per-subscriber counters, limits, and thresholds."
::= { natMIBGroups 13 }
natGroupSubscriberNotifications NOTIFICATION-GROUP
NOTIFICATIONS { natNotifSubscriberMappings }
STATUS current
DESCRIPTION
"Subscriber notifications."
::= { natMIBGroups 14 }
-- compliance statements
natBasicStatelessCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Basic stateless compliance with this MIB is attained when
the objects contained in the mandatory groups are
implemented."
MODULE -- this module
MANDATORY-GROUPS { natGroupStatelessObjects }
OBJECT natInstanceAlias
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { natMIBCompliances 3 }
natBasicStatefulCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Basic stateful compliance with this MIB is attained when the
objects contained in the mandatory groups are implemented."
MODULE -- this module
MANDATORY-GROUPS { natGroupStatelessObjects,
natGroupStatefulObjects,
natGroupBasicNotifications }
::= { natMIBCompliances 4 }
natAddrMapCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"NATs that have 'Paired IP address pooling' behavior
[RFC4787] and implement the objects in this group can claim
this level of compliance."
MODULE -- this module
MANDATORY-GROUPS { natGroupStatelessObjects,
natGroupStatefulObjects,
natGroupBasicNotifications,
natGroupAddrMapObjects,
natGroupAddrMapNotifications }
::= { natMIBCompliances 5 }
natFragmentsCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"NATs that have 'Receive Fragments Out of Order' behavior
[RFC4787] and implement the objects in this group can claim
this level of compliance."
MODULE -- this module
MANDATORY-GROUPS { natGroupStatelessObjects,
natGroupStatefulObjects,
natGroupBasicNotifications,
natGroupFragmentObjects }
::= { natMIBCompliances 6 }
natCGNCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"NATs that have 'Paired IP address pooling' and 'Receive
Fragments Out of Order' behavior [RFC4787] and implement the
objects in this group can claim this level of compliance.
This level of compliance is to be expected of a CGN
compliant with [RFC6888]."
MODULE -- this module
MANDATORY-GROUPS { natGroupStatelessObjects,
natGroupStatefulObjects,
natGroupBasicNotifications,
natGroupAddrMapObjects,
natGroupAddrMapNotifications,
natGroupFragmentObjects,
natGroupSubscriberObjects,
natGroupSubscriberNotifications }
::= { natMIBCompliances 7 }
END
There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability:
Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability:
There are no objects that are sensitive in their own right, such as passwords or monetary amounts.
SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPsec), there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module.
Implementations SHOULD provide the security features described by the SNMPv3 framework (see [RFC3410]), and implementations claiming compliance to the SNMPv3 standard MUST include full support for authentication and privacy via the User-based Security Model (USM) [RFC3414] with the AES cipher algorithm [RFC3826]. Implementations MAY also provide support for the Transport Security Model (TSM) [RFC5591] in combination with a secure transport such as SSH [RFC5592] or TLS/DTLS [RFC6353].
Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them.
IANA has assigned object identifier 123 to the natMIB module, with prefix iso.org.dod.internet.mgmt.mib-2 in the Network Management Parameters registry [SMI-NUMBERS].
No IANA actions are required by this document.