RFC 2544 Applicability Statement: Use on Production Networks Considered Harmful
draft-ietf-bmwg-2544-as-06

Abstract

Benchmarking Methodology Working Group (BMWG) has been developing key performance metrics and laboratory test methods since 1990, and continues this work at present. The methods described in RFC 2544 are intended to generate traffic that overloads network device resources in order to assess their capacity. Overload of shared resources would likely be harmful to user traffic performance on a production network, and there are further negative consequences identified with production application of the methods. This memo clarifies the scope of RFC 2544 and other IETF BMWG benchmarking work for isolated test environments only, and encourages new standards activity for measurement methods applicable outside that scope.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http:/⁠/⁠datatracker.ietf.org/⁠drafts/⁠current/⁠.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on March 06, 2013.

Copyright Notice

Copyright (c) 2012 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http:/⁠/⁠trustee.ietf.org/⁠license-⁠info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.

Table of Contents

• 1. Introduction
• 1.1. Requirements Language
• 2. Scope and Goals
• 3. The Concept of an Isolated Test Environment
• 4. Why RFC 2544 Methods are intended only for ITE
• 4.1. Experimental Control and Accuracy
• 4.2. Containing Damage
• 5. Advisory on RFC 2544 Methods in Production Networks
• 6. Considering Performance Testing in Production Networks
• 7. Security Considerations
• 8. IANA Considerations
• 9. Acknowledgements
• 10. References
• 10.1. Normative References
• 10.2. Informative References
• Authors' Addresses

1. Introduction

This memo clarifies the scope and use of IETF Benchmarking Methodology Working Group (BMWG) tests including [RFC2544], which discusses and defines several tests that may be used to characterize the performance of a network interconnecting device.

Benchmarking methodologies (beginning with [RFC2544]) have always relied on test conditions that can only be produced and replicated reliably in the laboratory. These methodologies are not appropriate for inclusion in wider specifications such as:

[RFC2544] used the term "real-world" to refer to production networks and to differentiate them from test networks.

1. Validation of telecommunication service configuration, such as the Committed Information Rate (CIR).
2. Validation of performance metrics in a telecommunication Service Level Agreement (SLA), such as frame loss and latency.
3. Telecommunication service activation testing, where traffic that shares network resources with the test might be adversely affected.

Above, we distinguish "telecommunication service" (where a network service provider contracts with a customer to transfer information between specified interfaces at different geographic locations) from the generic term "service". Below, we use the adjective "production" to refer to networks carrying live user traffic.

Although RFC 2544 has been held up as the standard reference for such testing, we believe that the actual methods used vary from [RFC2544] in significant ways. Since the only citation is to [RFC2544], the modifications are opaque to the standards community and to users in general.

Since applying the test traffic and methods described in [RFC2544] on a production network risks causing overload in shared resources there is direct risk of harming user traffic if the methods are misused in this way. Therefore, IETF BMWG developed this Applicability Statement for [RFC2544] to directly address the situation.

1.1. Requirements Language

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119].

2. Scope and Goals

This memo clarifies the scope of [RFC2544] with the goal to provide guidance to the industry on its applicability, which is limited to laboratory testing.

3. The Concept of an Isolated Test Environment

An Isolated Test Environment (ITE) used with [RFC2544] methods (as illustrated in Figures 1 through 3 of [RFC2544]) has the ability to:

• contain the test streams to paths within the desired set-up
• prevent non-test traffic from traversing the test set-up

These features allow unfettered experimentation, while at the same time protecting lab equipment management/control LANs and other production networks from the unwanted effects of the test traffic.

4. Why RFC 2544 Methods are intended only for ITE

The following sections discuss some of the reasons why [RFC2544] methods are applicable only for isolated laboratory use, and the consequences of applying these methods outside the lab environment.

4.1. Experimental Control and Accuracy

All of the tests described in RFC 2544 require that the tester and device under test are the only devices on the networks that are transmitting data. The presence of other traffic (unwanted on the ITE network) would mean that the specified test conditions have not been achieved and flawed results are a likely consequence.

If any other traffic appears and the amount varies over time, the repeatability of any test result will likely depend to some degree on the amount and variation of the other traffic.

The presence of other traffic makes accurate, repeatable, and consistent measurements of the performance of the device under test very unlikely, since the complete details of test conditions will not be reported.

For example, the RFC 2544 Throughput Test attempts to characterize a maximum reliable load, thus there will be testing above the maximum that causes packet/frame loss. Any other sources of traffic on the network will cause packet loss to occur at a tester data rate lower than the rate that would be achieved without the extra traffic.

4.2. Containing Damage

[RFC2544] methods, specifically to determine Throughput as defined in [RFC1242] and other benchmarks, may overload the resources of the device under test, and may cause failure modes in the device under test. Since failures can become the root cause of more wide-spread failure, it is clearly desirable to contain all test traffic within the ITE.

In addition, such testing can have a negative effect on any traffic that shares resources with the test stream(s) since, in most cases, the traffic load will be close to the capacity of the network links.

Appendix C.2.2 of [RFC2544] (as adjusted by errata) gives the private IPv4 address range for testing:

"...The network addresses 198.18.0.0 through 198.19.255.255 have been assigned to the BMWG by the IANA for this purpose. This assignment was made to minimize the chance of conflict in case a testing device were to be accidentally connected to part of the Internet. The specific use of the addresses is detailed below."

In other words, devices operating on the Internet may be configured to discard any traffic they observe in this address range, as it is intended for laboratory ITE use only. Thus, testers using the assigned testing address ranges are connected to the Internet and test packets are forwarded across the Internet, it is likely that the packets will be discarded and the test will not work.

We note that a range of IPv6 addresses has been assigned to BMWG for laboratory test purposes, in [RFC5180] (as amended by errata).

See the Security Considerations Section below for further considerations on containing damage.

5. Advisory on RFC 2544 Methods in Production Networks

The tests in [RFC2544] were designed to measure the performance of network devices, not of networks, and certainly not production networks carrying user traffic on shared resources. There will be undesirable consequences when applying these methods outside the isolated test environment.

One negative consequence stems from reliance on frame loss as an indicator of resource exhaustion in [RFC2544] methods. In practice, link-layer and physical-layer errors prevent production networks from operating loss-free. The [RFC2544] methods will not correctly assess Throughput when loss from uncontrolled sources is present. Frame loss occurring at the SLA levels of some networks could affect every iteration of Throughput testing (when each step includes sufficient packets to experience facility-related loss). Flawed results waste the time and resources of the testing service user and of the service provider when called to dispute the measurement. These are additional examples of harm that compliance with this advisory should help to avoid.

The methods described in [RFC2544] are intended to generate traffic that overloads network device resources in order to assess their capacity. Overload of shared resources would likely be harmful to user traffic performance on a production network. These tests MUST NOT be used on production networks and as discussed above. The tests will not produce a reliable or accurate benchmarking result on a production network.

[RFC2544] methods have never been validated on a network path, even when that path is not part of a production network and carrying no other traffic. It is unknown whether the tests can be used to measure valid and reliable performance of a multi-device, multi-network path. It is possible that some of the tests may prove valid in some path scenarios, but that work has not been done or has not been shared with the IETF community. Thus, such testing is contra-indicated by the BMWG.

6. Considering Performance Testing in Production Networks

The IETF has addressed the problem of production network performance measurement by chartering a different working group: IP Performance Metrics (IPPM). This working group has developed a set of standard metrics to assess the quality, performance, and reliability of Internet packet transfer services. These metrics can be measured by network operators, end users, or independent testing groups. We note that some IPPM metrics differ from RFC 2544 metrics with similar names, and there is likely to be confusion if the details are ignored.

IPPM has not yet standardized methods for raw capacity measurement of Internet paths. Such testing needs to adequately consider the strong possibility for degradation to any other traffic that may be present due to congestion. There are no specific methods proposed for activation of a packet transfer service in IPPM at this time. Thus, individuals who need to conduct capacity tests on production networks should actively participate in standards development to ensure their methods receive appropriate industry review and agreement, in the IETF or in alternate standards development organizations.

Other standards may help to fill gaps in telecommunication service testing. For example, the IETF has many standards intended to assist with network operation, administration and maintenance (OAM), and ITU-T Study Group 12 has a Recommendation on service activation test methodology [Y.1564].

The world will not spin off axis while waiting for appropriate and standardized methods to emerge from the consensus process.

7. Security Considerations

This Applicability Statement intends to help preserve the security of the Internet by clarifying that the scope of [RFC2544] and other BMWG memos are all limited to testing in a laboratory ITE, thus avoiding accidental Denial of Service attacks or congestion due to high traffic volume test streams.

All Benchmarking activities are limited to technology characterization using controlled stimuli in a laboratory environment, with dedicated address space and the other constraints [RFC2544].

The benchmarking network topology will be an independent test setup and MUST NOT be connected to devices that may forward the test traffic into a production network, or misroute traffic to the test management network.

Further, benchmarking is performed on a "black-box" basis, relying solely on measurements observable external to the device under test/system under test (DUT/SUT).

Special capabilities SHOULD NOT exist in the DUT/SUT specifically for benchmarking purposes. Any implications for network security arising from the DUT/SUT SHOULD be identical in the lab and in production networks.

8. IANA Considerations

This memo makes no requests of IANA.

9. Acknowledgements

Thanks to Matt Zekauskas, Bill Cerveny, Barry Constantine, Curtis Villamizar, David Newman, and Adrian Farrel for suggesting improvements to this memo.

Specifically, Al Morton would like to thank his co-authors, who constitute the complete set of Chairmen-Emeritus of the BMWG, for returning from other pursuits to develop this statement and see it through to approval. This has been a rare privilege; one that likely will not be matched in the IETF again:

   Scott Bradner   served as Chairman from 1990 to 1993
   Jim McQuaid     served as Chairman from 1993 to 1995
   Kevin Dubray    served as Chairman from 1995 to 2006

It's all about the band.

10. References

10.1. Normative References

10.2. Informative References

Authors' Addresses