| TOC |
|
By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as “work in progress.”
The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html.
This Internet-Draft will expire on May 1, 2009.
This document extends the IPFilterRule AVP functionality of the Diameter Base protocol and the functionality of the QoS-Filter-Rule AVP defined in RFC 4005. The ability to convey Quality of Service information using the AVPs defined in this document is available to existing and future Diameter applications where permitted by the command ABNF.
1.
Introduction
2.
Terminology
3.
Diameter QoS Defined AVPs
3.1.
QoS-Capability AVP
3.2.
QoS-Profile-Template AVP
3.3.
Vendor-Specific-QoS-Profile-Template AVP
3.4.
QoS-Resources AVP
3.5.
Extended-QoS-Filter-Rule AVP
3.6.
QoS-Semantics
3.7.
QoS-Parameters AVP
3.8.
QoS-Rule-Precedence AVP
4.
Semantics of QoS Parameters
5.
Diameter Classifier AVPs
5.1.
Classifier AVP
5.2.
Classifier-ID AVP
5.3.
Protocol AVP
5.4.
Direction AVP
5.5.
From-Spec AVP
5.6.
To-Spec AVP
5.7.
Source and Destination AVPs
5.7.1.
Negated AVP
5.7.2.
IP-Address AVP
5.7.3.
IP-Address-Range AVP
5.7.4.
IP-Address-Start AVP
5.7.5.
IP-Address-End AVP
5.7.6.
IP-Address-Mask AVP
5.7.7.
IP-Mask-Bit-Mask-Width AVP
5.7.8.
MAC-Address AVP
5.7.9.
MAC-Address-Mask AVP
5.7.10.
MAC-Address-Mask-Pattern AVP
5.7.11.
EUI64-Address AVP
5.7.12.
EUI64-Address-Mask AVP
5.7.13.
EUI64-Address-Mask-Pattern AVP
5.7.14.
Port AVP
5.7.15.
Port-Range AVP
5.7.16.
Port-Start AVP
5.7.17.
Port-End AVP
5.7.18.
Use-Assigned-Address AVP
5.8.
Header Option AVPs
5.8.1.
Diffserv-Code-Point AVP
5.8.2.
Fragmentation-Flag AVP
5.8.3.
IP-Option AVP
5.8.4.
IP-Option-Type AVP
5.8.5.
IP-Option-Value AVP
5.8.6.
TCP-Option AVP
5.8.7.
TCP-Option-Type AVP
5.8.8.
TCP-Option-Value AVP
5.8.9.
TCP-Flags AVP
5.8.10.
TCP-Flag-Type AVP
5.8.11.
ICMP-Type
5.8.12.
ICMP-Type-Number AVP
5.8.13.
ICMP-Code AVP
5.8.14.
ETH-Option AVP
5.8.15.
ETH-Proto-Type AVP
5.8.16.
ETH-Ether-Type AVP
5.8.17.
ETH-SAP AVP
5.8.18.
VLAN-ID-Range AVP
5.8.19.
S-VID-Start AVP
5.8.20.
S-VID-End AVP
5.8.21.
C-VID-Start AVP
5.8.22.
C-VID-End AVP
5.8.23.
ETH-Priority-Range AVP
5.8.24.
ETH-Low-Priority AVP
5.8.25.
ETH-High-Priority AVP
6.
Time Of Day AVPs
6.1.
Time-Of-Day-Condition AVP
6.2.
Time-Of-Day-Start AVP
6.3.
Time-Of-Day-End AVP
6.4.
Day-Of-Week-Mask AVP
6.5.
Day-Of-Month-Mask AVP
6.6.
Month-Of-Year-Mask AVP
6.7.
Absolute-Start-Time AVP
6.8.
Absolute-End-Time AVP
6.9.
Timezone-Flag AVP
6.10.
Timezone-Offset AVP
7.
Examples
7.1.
Diameter EAP with QoS Information
7.2.
Diameter NASREQ with QoS Information
7.3.
QoS Authorization
7.4.
Diameter Server Initiated Re-authorization of QoS
7.5.
Diameter Credit Control with QoS Information
7.6.
Classifier Examples
8.
Acknowledgments
9.
Contributors
10.
IANA Considerations
11.
Security Considerations
12.
References
12.1.
Normative References
12.2.
Informative References
§
Authors' Addresses
§
Intellectual Property and Copyright Statements
| TOC |
This document defines a number of Diameter Quality of Service (QoS) related AVPs that can be used in existing and future Diameter applications where permitted by the command ABNF. The Extended-QoS-Filter-Rule AVP thereby replaces the IPFilterRule, defined in RFC 3588bis [I‑D.ietf‑dime‑rfc3588bis] (Fajardo, V., Arkko, J., Loughney, J., and G. Zorn, “Diameter Base Protocol,” April 2010.), and the QoS-Filter-Rule, defined in RFC 4005 [RFC4005] (Calhoun, P., Zorn, G., Spence, D., and D. Mitton, “Diameter Network Access Server Application,” August 2005.).
| TOC |
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119] (Bradner, S., “Key words for use in RFCs to Indicate Requirement Levels,” March 1997.).
| TOC |
| TOC |
The QoS-Capability AVP (AVP Code TBD) is of type Grouped and contains a list of supported Quality of Service profile templates (and therefore the support of the respective parameter AVPs).
The QoS-Capability AVP may be used for a simple announcement of the QoS capabilities and QoS profiles supported by a peer. It may also be used to negotiate a mutually supported set of QoS capabilities and QoS profiles between two peers.
QoS-Capability ::= < AVP Header: XXX >
* [ QoS-Profile-Template ]
* [ Vendor-Specific-QoS-Profile-Template ]
* [ AVP ]
| TOC |
The QoS-Profile-Template AVP (AVP Code TBD) is of type Unsigned32 and contains a QoS profile template identifier. An initial QoS profile template is defined with value of 0 and is described in [I‑D.ietf‑dime‑qos‑parameters] (Korhonen, J., Tschofenig, H., and E. Davies, “Quality of Service Parameters for Usage with Diameter,” May 2009.). The registry for the QoS profile templates is created with the same document.
| TOC |
The Vendor-Specific-QoS-Profile-Template AVP (AVP Code TBD) is of type Grouped and defines a vendor-specific QoS profile template.
The Vendor-Id AVP contains a 32 bit IANA SMI Network Management Private Enterprise Code and the QoS-Profile-Template AVP contains the template identifier assigned by the vendor.
Vendor-Specific-QoS-Profile-Template ::= < AVP Header: XXX >
{ Vendor-Id }
{ QoS-Profile-Template }
* [ AVP ]
| TOC |
The QoS-Resources AVP (AVP Code TBD) is of type Grouped and includes a description of the Quality of Service resources for policing traffic flows.
QoS-Resources ::= < AVP Header: XXX >
* [ Extended-QoS-Filter-Rule ]
* [ AVP ]
| TOC |
The Extended-QoS-Filter-Rule AVP (AVP Code TBD) is of type Grouped and defines one or more traffic flows together with a set of QoS parameters that should be applied to the flow(s) by the Resource Management Function. This AVP uses the Classifier AVP (see Section 5 (Diameter Classifier AVPs)) to describe traffic flows.
Extended-QoS-Filter-Rule ::= < AVP Header: XXX >
{ QoS-Semantics }
[ QoS-Profile-Template ]
[ Vendor-Specific-QoS-Profile-Template ]
[ QoS-Parameters ]
[ QoS-Rule-Precedence ]
[ Classifier ]
* [ Time-Of-Day-Condition ]
* [ AVP ]
Either the QoS-Profile-Template or Vendor-Specific-QoS-Profile-Template AVP MUST appear in the Extended-QoS-Filter-Rule AVP.
| TOC |
The QoS-Semantics AVP (AVP Code TBD) is of type Enumerated and provides the semantics for the QoS-Profile-Template and QoS-Parameters AVPs in the Extended-QoS-Filter-Rule AVP.
This document defines the following values:
(0): QoS-Desired (1): QoS-Available (2): QoS-Reserved (3): Minimum-QoS (4): QoS-Authorized
| TOC |
The QoS-Parameters AVP (AVP Code TBD) is of type OctetString and contains Quality of Service parameters. These parameters are defined in a separate document, see [I‑D.ietf‑dime‑qos‑parameters] (Korhonen, J., Tschofenig, H., and E. Davies, “Quality of Service Parameters for Usage with Diameter,” May 2009.).
| TOC |
The QoS-Rule-Precedence AVP (AVP Code TBD) is of type Unsigned32 and specifies the execution order of the rules expressed in the QoS-Resources AVP. Rules with equal precedence MAY be executed in parallel if supported by the Resource Management Function. If the QoS-Rule-Precedence AVP is absent from the Extended-QoS-Filter-Rule AVP, the rules SHOULD be executed in the order in which they appear in the QoS-Resources AVP. The lower the numerical value of QoS-Rule-Precedence AVP, the higher the rule precedence.
| TOC |
The QoS parameters carried in the QoS-Resources AVP may appear in different messages. The semantic of the QoS parameters depend on the information provided in the QoS-Semantics AVP which currently defines 5 values, namely QoS-Desired (0), QoS-Available (1), QoS-Reserved (2), Minimum-QoS (3), and QoS-Authorized (4).
The semantics of the different values are as follows:
Object Type Direction Semantic
---------------------------------------------------------------------
QoS-Desired C->S Please authorize the indicated QoS
QoS-Desired C<-S NA
QoS-Available C->S Admission Control at interface indicates
that this QoS is available. (note 1)
QoS-Available C<-S Indicated QoS is available. (note 2)
QoS-Reserved C->S Used for reporting during accounting.
QoS-Reserved C<-S NA
Minimum-QoS C->S Indicates that the client is not
interested in authorizing QoS that is
lower than Min. QoS.
Minimum-QoS C<-S The client must not provide QoS
guarantees lower than Min. QoS.
QoS-Authorized C->S NA
QoS-Authorized C<-S Indicated QoS authorized
Legend:
C: Diameter client
S: Diameter server
NA: Not applicable to this document;
no semantic defined in this specification
Notes:
(1) QoS-Available is only useful in relationship with QoS-Desired
(and optionally with Minimum-QoS).
(2) QoS-Available is only useful when the AAA server performs
admission control and knows about the resources in the network.
| TOC |
Classifiers are used in many applications to specify how to classify packets. For example in a QoS application, if a packet matches a classifier then that packet will be treated in accordance with a QoS specification associated with that classifier.
The Classifiers are sent to on on-path element (e.g. a router) which uses the classifier to match packets. Figure 1 (Example of a Classifier Architecture) shows a typical deployment.
+-----------+
+-----------+|
+--------+ +-------------+ +------------+||
| | IN | | | |||
| +--------->| +------------->| |||
|Managed | | Classifying | | Unmanaged |||
|Terminal| OUT | Entity | | Terminal |||
| |<---------+ |<-------------+ ||+
| | | | | |+
+--------+ +-------------+ +------------+
^
| Classifiers
|
+------+-------+
| |
| AAA |
| |
+--------------+
| Figure 1: Example of a Classifier Architecture |
The managed terminal, the terminal for which the classifiers are being specified is located on the left of the Classifying Entity. The unmanaged terminal, the terminal that receives packets from the Managed terminal or sends packets to the managed terminal is located to the right side of the Classifying Entity.
The Classifying Entity is responsible for classifying packets that are incoming (IN) from the Managed Terminal or packets outgoing (OUT) to the Managed Terminal.
A Classifier consists of a group of attributes that specify how to match a packet. Each set of attributes expresses values about aspects of the packet - typically the packet header. Different protocols therefore would use different attributes.
In general a Classifier consists of the following:
- Identifier:
The identifier uniquely identifies this classifier and may be used to reference the classifier from another structure.
- From:
Specifies the rule for matching the source part of the packet.
- To:
Specifies the rule for matching the destination part of the packet.
- Protocol:
Specifies the matching protocol of the packet.
- Direction:
Specifies whether the classifier is to apply to packets flowing from the Managed Terminal (IN) or to packets flowing to the Managed Terminal (OUT), or packets flowing in both direction.
- Options:
Associated with each protocol or layer, or various values specific to the header of the protocol or layer. Options allow matching on those values.
Each protocol type will have a specific set of attributes that can be used to specify a classifier for that protocol. These attributes will be grouped under a grouped AVP called a Classifier AVP.
| TOC |
The Classifier AVP (AVP Code TBD) is a grouped AVP that consists of a set of attributes that specify how to match a packet.
Classifier ::= < AVP Header: XXX >
{ Classifier-ID }
{ Protocol }
{ Direction }
* [ From-Spec ]
* [ To-Spec ]
* [ Diffserv-Code-Point ]
[ Fragmentation-Flag ]
* [ IP-Option ]
* [ TCP-Option ]
[ TCP-Flags ]
* [ ICMP-Type ]
* [ ETH-Option ]
* [ AVP ]
| TOC |
The Classifier-ID AVP (AVP Code TBD) is of type OctetString and uniquely identifies the classifier. Each application will define the uniqueness scope of this identifier, e.g. unique per terminal or globally unique. Exactly one Classifier-ID AVP MUST be contained within a Classifier AVP.
| TOC |
The Protocol AVP (AVP Code TBD) is of type Enumerated and specifies the protocol being matched. The attributes included in the Classifier AVP must be consistent with the value of the Protocol AVP. Exactly one Protocol AVP MUST be contained within a Classifier AVP. The values for this AVP are managed by IANA under the Protocol Numbers registry [PROTOCOL] (IANA, “Protocol Types,” .).
| TOC |
The Direction AVP (AVP Code TBD) is of type Enumerated that specifies in which direction to apply the Classifier. The values of the enumeration are: "IN","OUT","BOTH". In the "IN" and "BOTH" directions, the From-Spec refers to the address of the Managed Terminal and the To-Spec refers to the unmanaged terminal. In the "OUT" direction, the From-Spec refers to the Unmanaged Terminal whereas the To-Spec refers to the Managed Terminal.
Value | Name and Semantic
------+--------------------------------------------------
0 | RESERVED
1 | IN - The classifier applies to flows from the
| Managed Terminal.
2 | OUT - The classifier applies to flows to the
| Managed Terminal.
3 | BOTH - The classifier applies to flows both to
| and from the Managed Terminal.
| TOC |
The From-Spec AVP (AVP Code TBD) is a grouped AVP that specifies the Source Specification used to match the packet. Zero or more of these AVPs may appear in the Classifier. If this AVP is absent from the Classifier then all packets are matched regardless of the source address. If more than one instance of this AVP appears in the Classifier then the source of the packet can match any From-Spec AVP. The contents of this AVP are protocol specific.
If more than one instance of the IP address AVPs (IP-Address, IP-Address-Range, IP-Address-Mask, Use-Assigned-Address) appear in the From-Spec AVP then the source IP address of the packet must match one of the addresses represented by these AVPs.
If more that one instance of the layer 2 address AVPs (MAC-Address, MAC-Address-Mask, EUI64-Address, EUI64-Address-Mask) appears in the From-Spec then the the source layer 2 address of the packet must match one of the addresses represented in these AVPs.
If more that one instance of the port AVPs (Port, Port-Range) appears in the From-Spec AVP then the source port number must match one of the port numbers represented in these AVPs.
If the IP address, MAC address and port AVPs appear in the same From-Spec AVP then the source packet must match all the specifications, i.e. match the IP address AND MAC address AND port number.
From-Spec ::= < AVP Header: XXX >
* [ IP-Address ]
* [ IP-Address-Range ]
* [ IP-Address-Mask ]
* [ MAC-Address ]
* [ MAC-Address-Mask]
* [ EUI64-Address ]
* [ EUI64-Address-Mask]
* [ Port ]
* [ Port-Range ]
[ Negated ]
[ Use-Assigned-Address ]
* [ AVP ]
| TOC |
The To-Spec AVP (AVP Code TBD) is a grouped AVP that specifies the Destination Specification used to match the packet. Zero or more of these AVPs may appear in the Classifier. If this AVP is absent from the Classifier then all packets are matched regardless of the destination address. If more than one instance of this AVP appears in the Classifier then the destination of the packet can match any To-Spec AVP. The contents of this AVP are protocol specific.
If more than one instance of the IP address AVPs (IP-Address, IP-Address-Range, IP-Address-Mask, Use-Assigned-Address) appear in the To-Spec AVP then the destination IP address of the packet must match one of the addresses represented by these AVPs.
If more that one instance of the layer 2 address AVPs (MAC-Address, MAC-Address-Mask, EUI64-Address, EUI64-Address-Mask) appears in the To-Spec then the the destination layer 2 address of the packet must match one of the addresses represented in these AVPs.
If more that one instance of the port AVPs (Port, Port-Range) appears in the To-Spec AVP then the destination port number must match one of the port numbers represented in these AVPs.
If the IP address, MAC address and port AVPs appear in the same To-Spec AVP then the destination packet must match all the specifications, i.e. match the IP address AND MAC address AND port number.
To-Spec ::= < AVP Header: XXX >
* [ IP-Address ]
* [ IP-Address-Range ]
* [ IP-Address-Mask ]
* [ MAC-Address ]
* [ MAC-Address-Mask]
* [ EUI64-Address ]
* [ EUI64-Address-Mask]
* [ Port ]
* [ Port-Range ]
[ Negated ]
[ Use-Assigned-Address ]
* [ AVP ]
| TOC |
For packet classification the contents of the From-Spec and To-Spec can contain the following AVPs.
By combining several of these AVPs within a From-Spec or To-Spec AVP and using more than one From-Spec or To-Spec AVP in the Classifier AVP, one can express many different types of address pools.
| TOC |
The Negated AVP (AVP Code TBD) of type Enumerated containing the values of True or False. Exactly zero or one of these AVPs may appear in the From-Spec or To-Spec AVP. When set to True the meaning of the match in the To-Spec and From-Spec are negated, causing all other addresses to be matched instead.
When set to False, or when the AVP is not included in the From-Spec or To-Spec AVP then the meaning of the match is not inverted, causing only the addresses specified to be matched.
Note that the negation does not impact the port comparisons.
Value | Name
------+--------
0 | False
1 | True
| TOC |
The IP-Address AVP (AVP Code TBD) is of type Address and specifies a single IP address (IPv4 or IPv6) address to match.
| TOC |
The IP-Address-Range AVP (AVP Code TBD) is of type Grouped and specifies an inclusive IP address range.
IP-Address-Range ::= < AVP Header: XXX >
[ IP-Address-Start ]
[ IP-Address-End ]
* [ AVP ]
If the IP-Address-Start AVP is not included then the address range starts from the first valid IP address up to and including the specified IP-Address-End address.
If the IP-Address-End AVP is not included then the address range starts at the address specified by the IP-Address-Start AVP and includes all the remaining valid IP addresses.
For the IP-Address-Range AVP to be valid, the IP-Address-Start AVP MUST contain a value that is less than that of the IP-Address-End AVP.
| TOC |
The IP-Address-Start AVP (AVP Code TBD) is of type Address and specifies the first IP address (IPv4 or IPv6) address of an IP address range.
| TOC |
The IP-Address-End AVP (AVP Code TBD) is of type Address and specifies the last IP address (IPv4 or IPv6) address of an address range.
| TOC |
The IP-Address-Mask AVP (AVP Code TBD) is of type Grouped and specifies an IP address range using a base IP address and the bit-width of the mask. For example, a range expressed as 1.2.3.0/24 will match all IP addresses from 1.2.3.0 up to and including 1.2.3.255. The bit-width MUST be valid for the type of IP address.
IP-Address-Mask ::= < AVP Header: XXX >
{ IP-Address }
{ IP-Bit-Mask-Width }
* [ AVP ]
| TOC |
The IP-Bit-Mask-Width AVP (AVP Code TBD) is of type OctetString. The value is a single octet and specifies the width of an IP address bit-mask.
| TOC |
The MAC-Address AVP (AVP Code TBD) is of type OctetString and specifies a single layer 2 address in MAC-48 format. The value is a 6 octets encoding of the address as it would appear in the frame header.
| TOC |
The MAC-Address-Mask AVP (AVP Code TBD) is of type Grouped and specifies a set of MAC addresses using a bit mask to indicate the bits of the MAC addresses which must fit to the specified MAC address attribute. For example, a MAC-Address-Mask with the MAC-Address as 00-10-A4-23-00-00 and with a MAC-Address-Mask-Pattern of FF-FF-FF-FF-00-00 will match all MAC addresses from 00-10-A4-23-00-00 up to and including 00-10-A4-23-FF-FF.
MAC-Address-Mask ::= < AVP Header: XXX >
{ MAC-Address }
{ MAC-Address-Mask-Pattern }
* [ AVP ]
| TOC |
The MAC-Address-Mask-Pattern AVP (AVP Code TBD) is of type OctetString. The value is a 6 octets specifying the bit positions of a MAC address, that are taken for matching.
| TOC |
The EUI64-Address AVP (AVP Code TBD) is of type OctetString and specifies a single layer 2 address in EUI-64 format. The value is a 8 octets encoding of the address as it would appear in the frame header.
| TOC |
The EUI64-Address-Mask AVP (AVP Code TBD) is of type Grouped and specifies a set of EUI64 addresses using a bit mask to indicate the bits of the EUI64 addresses which must fit to the specified EUI64 address attribute. For example, a EUI64-Address-Mask with the EUI64-Address as 00-10-A4-FF-FE-23-00-00 and with a EUI64-Address-Mask-Pattern of FF-FF-FF-FF-FF-FF-00-00 will match all EUI64 addresses from 00-10-A4-FF-FE-23-00-00 up to and including 00-10-A4-FF-FE-23-FF-FF.
EUI64-Address-Mask ::= < AVP Header: XXX >
{ EUI64-Address }
{ EUI64-Address-Mask-Pattern }
* [ AVP ]
| TOC |
The EUI64-Address-Mask-Pattern AVP (AVP Code TBD) is of type OctetString. The value is a 8 octets specifying the bit positions of a EUI64 address, that are taken for matching.
| TOC |
The Port AVP (AVP Code TBD) is of type Integer32 in the range of 0 to 65535 and specifies the TCP or UDP port number to match.
| TOC |
The Port-Range AVP (AVP Code TBD) is of type Grouped and specifies an inclusive range of ports.
Port-Range ::= < AVP Header: XXX >
[ Port-Start ]
[ Port-End ]
* [ AVP ]
If the Port-Start AVP is omitted then port 0 is assumed. If the Port-End AVP is omitted then port 65535 is assumed.
| TOC |
The Port-Start AVP (AVP Code TBD) is of type Integer32 and specifies the first port number of an IP port range.
| TOC |
The Port-End AVP (AVP Code TBD) is of type Integer32 and specifies the last port number of an IP port range.
| TOC |
In some scenarios, the AAA does not know the IP address assigned to the Managed Terminal at the time that the Classifier is sent to the Classifying Entity. The Use-Assigned-Address AVP (AVP Code TBD) is of type Enumerated containing the values of True or False. When present and set to True, it represents the IP address assigned to the Managed Terminal.
Value | Name
------+--------
0 | False
1 | True
| TOC |
The Classifier AVP may contain one or more of the following AVPs to match on the various possible IP, TCP or ICMP header options.
| TOC |
The Diffserv-Code-Point AVP (AVP Code TBD) is of type Enumerated and specifies the Differentiated Services Field Codepoints to match in the IP header. The values are managed by IANA under the Differentiated Services Field Codepoints registry [DSCP] (IANA, “Differentiated Services Field Codepoints,” .).
| TOC |
The Fragmentation-Flag AVP (AVP Code TBD) is of type Enumerated and specifies the packet fragmentation flags to match in the IP header.
Value | Name and Semantic
------+------------------------------------------------------------
0 | RESERVED
1 | Don't Fragment (DF)
2 | More Fragments (MF)
| TOC |
The IP-Option AVP (AVP Code TBD) is of type Grouped and specifies an IP header option that must be matched.
IP-Option ::= < AVP Header: XXX >
{ IP-Option-Type }
* [ IP-Option-Value ]
[ Negated ]
* [ AVP ]
If one or more IP-Option-Value AVPs are present, one of the values MUST match the value in the IP header option. If the IP-Option-Value AVP is absent, the option type MUST be present in the IP header but the value is wild carded.
The Negated AVP is used in conjunction with the IP-Option-Value AVPs to specify IP header options which do not match specific values. The Negated AVP is used without the IP-Option-Value AVP to specify IP headers which do not contain the option type.
| TOC |
The IP-Option-Type AVP (AVP Code TBD) is of type Enumerated and the values are managed by IANA under the IP Option Numbers registry [IPOPTIONS] (IANA, “IP Option Numbers,” .).
| TOC |
The IP-Option-Value AVP (AVP Code TBD) is of type OctetString and contains the option value that must be matched.
| TOC |
The TCP-Option AVP (AVP Code TBD) is of type Grouped and specifies a TCP header option that must be matched.
TCP-Option ::= < AVP Header: XXX >
{ TCP-Option-Type }
* [ TCP-Option-Value ]
[ Negated ]
* [ AVP ]
If one or more TCP-Option-Value AVPs are present, one of the values MUST match the value in the TCP header option. If the TCP-Option-Value AVP is absent, the option type MUST be present in the TCP header but the value is wild carded.
The Negated AVP is used in conjunction which the TCP-Option-Value AVPs to specify TCP header options which do not match specific values. The Negated AVP is used without the TCP-Option-Value AVP to specify TCP headers which do not contain the option type.
| TOC |
The TCP-Option-Type AVP (AVP Code TBD) is of type Enumerated and the values are managed by IANA under the TCP Option Numbers registry [TCPOPTIONS] (IANA, “TCP Option Numbers,” .).
| TOC |
The TCP-Option-Value AVP (AVP Code TBD) is of type OctetString and contains the option value that must be matched.
| TOC |
The TCP-Flags AVP (AVP Code TBD) is of type Grouped and specifies a set of TCP control flags that must be matched.
TCP-Flags ::= < AVP Header: XXX >
1* { TCP-Flag-Type }
[ Negated ]
* [ AVP ]
If the Negated AVP is not present, the TCP-Flag-Type AVPs specifies which flags MUST be set. If the Negated AVP is present, the TCP-Flag-Type AVPs specifies which flags MUST be cleared.
| TOC |
The TCP-Flag-Type AVP (AVP Code TBD) is of type Enumerated and specifies a TCP control flag type that must be matched.
Value | Name and Semantic
------+------------------------------------------------------------
0 | RESERVED
1 | CWR - Congestion Window Reduced.
2 | ECE - ECN-Echo. TCP peer is ECN capable.
3 | URG - URGent pointer field is significant.
4 | ACK - ACKnowledgment field is significant.
5 | PSH - Push function.
6 | RST - Reset the connection.
7 | SYN - Synchronize sequence numbers.
8 | FIN - No more data from sender.
| TOC |
The ICMP-Type AVP (AVP Code TBD) is of type Grouped and specifies a ICMP message type that must be matched.
ICMP-Type ::= < AVP Header: XXX >
{ ICMP-Type-Number }
* [ ICMP-Code ]
[ Negated ]
* [ AVP ]
If the ICMP-Code AVP is present, the value MUST match that in the ICMP header. If the ICMP-Code AVP is absent, the ICMP type MUST be present in the ICMP header but the code is wild carded.
The Negated AVP is used in conjunction which the ICMP-Code AVPs to specify ICMP codes which do not match specific values. The Negated AVP is used without the ICMP-Code AVP to specify ICMP headers which do not contain the ICMP type.
| TOC |
The ICMP-Type-Number AVP (AVP Code TBD) is of type Enumerated and the values are managed by IANA under the ICMP Type Numbers registry [ICMPTYPE] (IANA, “ICMP Type Numbers,” .).
| TOC |
The ICMP-Code AVP (AVP Code TBD) is of type Enumerated and the values are managed by IANA under the ICMP Type Numbers registry [ICMPTYPE] (IANA, “ICMP Type Numbers,” .).
| TOC |
The ETH-Option AVP (AVP Code TBD) is of type Grouped and specifies Ethernet specific attributes.
ETH-Option ::= < AVP Header: XXX >
{ ETH-Proto-Type }
* [ VLAN-ID-Range ]
* [ ETH-Priority-Range ]
* [ AVP ]
| TOC |
The Eth-Proto-Type AVP (AVP Code TBD) is of type Grouped and specifies the encapsulated protocol type. ETH-Ether-Type and ETH-SAP are mutually exclusive.
ETH-Proto-Type ::= < AVP Header: XXX >
* [ ETH-Ether-Type ]
* [ ETH-SAP ]
* [ AVP ]
| TOC |
The ETH-Ether-Type AVP (AVP Code TBD) is of type OctetString. The value is a double octet the contains the value of the Ethertype field in the packet to match. This AVP MAY be present in the case of DIX or if SNAP is present at 802.2 but the ETH-SAP AVP MUST NOT be present in this case.
| TOC |
The ETH-SAP AVP (AVP Code TBD) is of type OctetString. The value is a double octet representing the 802.2 SAP as specified in [IEEE802.2] (IEEE, “IEEE Standard for Information technology, Telecommunications and information exchange between systems, Local and metropolitan area networks, Specific requirements, Part 2: Logical Link Control,” 1998.). The first octet contains the DSAP and the second the SSAP.
| TOC |
The VLAN-ID-Range AVP (AVP Code TBD) is of type Grouped and specifies the VLAN range to match. VLAN identities are either specified by a single VLAN-ID according to [IEEE802.1Q] (IEEE, “IEEE Standard for Local and metropolitan area networks, Virtual Bridged Local Area Networks,” 2005.) or by a combination of Customer and Service VLAN-IDs according to [IEEE802.1ad] (IEEE, “IEEE Standard for Local and metropolitan area networks, Virtual Bridged Local Area Networks, Amendment 4: Provider Bridges,” 2005.).
The single VLAN-ID is represented by the C-VID-Start and C-VID-End AVPs and the S-VID-Start and S-VID-End AVPs SHALL be ommitted in this case. If the VLAN-ID-Range AVP is omitted from the Classifier, then comparison of the VLAN identity of the packet is irrelevant.
VLAN-ID-Range ::= < AVP Header: XXX >
[ S-VID-Start ]
[ S-VID-End ]
[ C-VID-Start ]
[ C-VID-End ]
* [ AVP ]
When the S-VID-Start AVP is present but the S-VID-End AVP is absent, the S-VID-Start AVP value MUST equal the value of the IEEE 802.1ad S-VID bits specified in [IEEE802.1ad] (IEEE, “IEEE Standard for Local and metropolitan area networks, Virtual Bridged Local Area Networks, Amendment 4: Provider Bridges,” 2005.) for a successful match. When both S-VID-Start and S-VID-End AVPs are present, the value of the IEEE 802.1ad S-VID bits MUST be greater than or equal to the S-VID-Start AVP value and less than or equal to the S-VID-End AVP value for a successful match. If the S-VID-Start and S-VID-End AVPs are omitted, then existence of IEEE802.1ad encapsulation or comparison of the IEEE 802.1ad S-VID bits is irrelevamt for this Classifier. If the S-VID-Start and S-VID-End AVPs are specified, then Ethernet packets without IEEE 802.1ad encapsulation MUST NOT match this Classifier.
When the C-VID-Start AVP is present but the C-VID-End AVP is absent, the C-VID-Start AVP value MUST equal the value of the IEEE 802.1ad C-VID bits specified in [IEEE802.1ad] (IEEE, “IEEE Standard for Local and metropolitan area networks, Virtual Bridged Local Area Networks, Amendment 4: Provider Bridges,” 2005.) or the IEEE 802.1Q VLAN-ID bits specified in [IEEE802.1Q] (IEEE, “IEEE Standard for Local and metropolitan area networks, Virtual Bridged Local Area Networks,” 2005.) for a successful match. When both C-VID-Start and C-VID-End AVPs are present, the value of the IEEE 802.1ad C-VID bits or the IEEE 802.1Q VLAN-ID bits MUST be greater than or equal to the C-VID-Start AVP value and less than or equal to the C-VID-End AVP value for a successful match. If the C-VID-Start and C-VID-End AVPs are omitted, then comparison of the IEEE 802.1ad C-VID bits or IEEE 802.1Q VLAN-ID bits for this Classifier is irrelevant. If the C-VID-Start and C-VID-End AVPs are specified, then Ethernet packets without IEEE 802.1ad or IEEE 802.1Q encapsulation MUST NOT match this Classifier.
| TOC |
The S-VID-Start AVP (AVP Code TBD) is of type Unsigned32. The value MUST be in the range from 0 to 4095. The value of this AVP specifies the start value of the range of S-VID VLAN-IDs to be matched.
| TOC |
The S-VID-End AVP (AVP Code TBD) is of type Unsigned32. The value MUST be in the range from 0 to 4095. The value of this AVP specifies the end value of the range of S-VID VLAN-IDs to be matched.
| TOC |
The C-VID-Start AVP (AVP Code TBD) is of type Unsigned32. The value MUST be in the range from 0 to 4095. The value of this AVP specifies the start value of the range of C-VID VLAN-IDs to be matched.
| TOC |
The C-VID-End AVP (AVP Code TBD) is of type Unsigned32. The value MUST be in the range from 0 to 4095. The value of this AVP specifies the end value of the range of C-VID VLAN-IDs to be matched.
| TOC |
The ETH-Priority-Range AVP (AVP Code TBD) is of type Grouped and specifies an inclusive range to match the user_priority parameter specified in [IEEE802.1D] (IEEE, “IEEE Standard for Local and metropolitan area networks, Media Access Control (MAC) Bridges,” 2004.). An Ethernet packet containing the user_priority parameter matches this Classifier if the value is greater than or equal to ETH-Low-Priority and less than or equal to ETH-High-Priority. If this AVP is omitted, then comparison of the IEEE 802.1D user_priority parameter for this Classifier is irrelevant.
ETH-Priority-Range ::= < AVP Header: XXX >
* [ ETH-Low-Priority ]
* [ ETH-High-Priority ]
* [ AVP ]
| TOC |
The ETH-Low-Priority AVP (AVP Code TBD) is of type Unsigned32. The value MUST be in the range from 0 to 7.
| TOC |
The ETH-High-Priority AVP (AVP Code TBD) is of type Unsigned32. The value MUST be in the range from 0 to 7.
| TOC |
In many QoS applications, the QoS specification applied to the traffic flow is conditional upon the time of day when the flow was observed. The following sections define AVPs that can be used to express one or more time windows which determine when a QoS specification is applicable to a traffic flow.
| TOC |
The Time-Of-Day-Condition AVP (AVP Code TBD) is of type Grouped and specifies one or more time windows.
Time-Of-Day-Condition ::= < AVP Header: XXX >
[ Time-Of-Day-Start ]
[ Time-Of-Day-End ]
[ Day-Of-Week-Mask ]
[ Day-Of-Month-Mask ]
[ Month-Of-Year-Mask ]
[ Absolute-Start-Time ]
[ Absolute-End-Time ]
[ Timezone-Flag ]
* [ AVP ]
If more than one instance of this AVP is present in the Extended-QoS-Filter-Rule AVP, the current time at QoS rule evaluation MUST be within at least one of the time windows specified in one of the Time-Of-Day-Condition AVPs.
When the Time-Of-Day-Condition AVP and Classifier AVP are present in the same Extended-QoS-Filter-Rule AVP, both the time of day and packet classification conditions MUST match for the QoS specification to be applied.
For example, a time window for 9am to 5pm (local time) from Monday to Friday would be expressed as:
Time-Of-Day-Condition = {
Time-Of-Day-Start = 32400;
Time-Of-Day-End = 61200;
Day-Of-Week-Mask =
( MONDAY | TUESDAY | WEDNESDAY | THURSDAY | FRIDAY );
Timezone-Flag = LOCAL;
}
| TOC |
The Time-Of-Day-Start AVP (AVP Code TBD) is of type Unsigned32. The value MUST be in the range from 0 to 86400. The value of this AVP specifies the start of an inclusive time window expressed as the offset in seconds from midnight. If this AVP is absent from the Time-Of-Day-Condition AVP, the time window starts at midnight.
| TOC |
The Time-Of-Day-End AVP (AVP Code TBD) is of type Unsigned32. The value MUST be in the range from 1 to 86400. The value of this AVP specifies the end of an inclusive time window expressed as the offset in seconds from midnight. If this AVP is absent from the Time-Of-Day-Condition AVP, the time window ends one second before midnight.
| TOC |
The Day-Of-Week-Mask AVP (AVP Code TBD) is of type Unsigned32. The value is a bitmask which specifies the day of the week for the time window to match. This document specifies the following bits:
Bit | Name
------+------------
0 | SUNDAY
1 | MONDAY
2 | TUESDAY
3 | WEDNESDAY
4 | THURSDAY
5 | FRIDAY
6 | SATURDAY
The bit MUST be set for the time window to match on the corresponding day of the week. Bit 0 is the most significant bit and unused bits MUST be cleared. If this AVP is absent from the Time-Of-Day-Condition AVP, the time windows match on all days of the week.
| TOC |
The Day-Of-Week-Month AVP (AVP Code TBD) is of type Unsigned32. The value MUST be in the range from 0 to 2147483647. The value is a bitmask which specifies the days of the month where bit 0 represents the first day of the month through to bit 30 which represents the last day of the month. The bit MUST be set for the time window to match on the corresponding day of the month. Bit 0 is the most significant bit and unused bits MUST be cleared. If this AVP is absent from the Time-Of-Day-Condition AVP, the time windows match on all days of the month.
| TOC |
The Month-Of-Year-Month AVP (AVP Code TBD) is of type Unsigned32. The value is a bitmask which specifies the months of the year for the time window to match. This document specifies the following bits:
Bit | Name
------+-----------
0 | JANUARY
1 | FEBRUARY
2 | MARCH
3 | APRIL
4 | MAY
5 | JUNE
6 | JULY
7 | AUGUST
8 | SEPTEMBER
9 | OCTOBER
10 | NOVEMBER
11 | DECEMBER
The bit MUST be set for the time window to match on the corresponding month of the year. Bit 0 is the most significant bit and unused bits MUST be cleared. If this AVP is absent from the Time-Of-Day-Condition AVP, the time windows match during all months of the year.
| TOC |
The Absolute-Start-Time AVP (AVP Code TBD) is of type Time. The value of this AVP specifies the time in seconds since January 1, 1900, 00:00 UTC when the time window starts. If this AVP is absent from the Time-Of-Day-Condition AVP, the time window starts on January 1, 1900, 00:00 UTC.
| TOC |
The Time-Of-Day-End AVP (AVP Code TBD) is of type Time. The value of this AVP specifies the time in seconds since January 1, 1900, 00:00 UTC when the time window ends. If this AVP is absent from the Time-Of-Day-Condition AVP, the time window is open-ended.
| TOC |
The Timezone-Flag AVP (AVP Code TBD) is of type Enumerated and indicates whether the time windows are specified in UTC, local time at the managed terminal or as an offset from UTC. If this AVP is absent from the Time-Of-Day-Condition AVP, the time windows are in UTC.
This document defines the following values:
Value | Name and Semantic
------+--------------------------------------------------
0 | RESERVED
1 | UTC - The time windows are expressed in UTC.
2 | LOCAL - The time windows are expressed in local
| time at the Managed Terminal.
3 | OFFSET - The time windows are expressed as an
| offset from UTC (see Timezone-Offset AVP).
| TOC |
The Timezone-Offset AVP (AVP Code TBD) is of type Integer32. The value of this AVP MUST be in the range from -43200 to 43200. It specifies the offset in seconds from UTC that was used to express Time-Of-Day-Start, Time-Of-Day-End, Day-Of-Week-Mask, Day-Of-Month-Mask and Month-Of-Year-Mask AVPs. This AVP MUST be present if the Timezone-Flag AVP is set to OFFSET.
| TOC |
This section shows a number of signaling flows where QoS negotiation and authorization is part of the conventional NASREQ, EAP or Credit Control applications message exchanges. The signalling flows for the Diameter QoS Application are described in [I‑D.ietf‑dime‑diameter‑qos] (Sun, D., McCann, P., Tschofenig, H., ZOU), T., Doria, A., and G. Zorn, “Diameter Quality of Service Application,” March 2010.).
| TOC |
Figure 2 (Example of a Diameter EAP enhanced with QoS Information) shows a simple signaling flow where a NAS
(Diameter Client) announces its QoS awareness and capabilities included into the DER
message and as part of the access authentication procedure. Upon completion of the
EAP exchange, the Diameter Server provides a pre-provisioned QoS profile with the
QoS-Semantics in the Extended-QoS-Filter-Rule AVP set to "QoS-Authorized", to the
NAS in the final DEA message.
End Diameter Diameter Host Client Server | | | | (initiate EAP) | | |<----------------------------->| | | | Diameter-EAP-Request | | | EAP-Payload(EAP Start) | | | QoS-Capability | | |------------------------------->| | | | | | Diameter-EAP-Answer | | Result-Code=DIAMETER_MULTI_ROUND_AUTH | | | EAP-Payload(EAP Request #1) | | |<-------------------------------| | EAP Request(Identity) | | |<------------------------------| | : : : : <<<more message exchanges>>> : : : : | | | | EAP Response #N | | |------------------------------>| | | | Diameter-EAP-Request | | | EAP-Payload(EAP Response #N) | | |------------------------------->| | | | | | Diameter-EAP-Answer | | | Result-Code=DIAMETER_SUCCESS | | | EAP-Payload(EAP Success) | | | [EAP-Master-Session-Key] | | | (authorization AVPs) | | | QoS-Resources(QoS-Authorized) | | |<-------------------------------| | | | | EAP Success | | |<------------------------------| | | | |
| Figure 2: Example of a Diameter EAP enhanced with QoS Information |
| TOC |
Figure 3 (Example of a Diameter NASREQ enhanced with QoS Information) shows a similar pre-provisioned QoS signaling as in Figure 2 (Example of a Diameter EAP enhanced with QoS Information) but using the NASREQ application instead of EAP application.
End Diameter
Host NAS Server
| | |
| Start Network | |
| Attachment | |
|<---------------->| |
| | |
| |AA-Request |
| |NASREQ-Payload |
| |QoS-Capability |
| +----------------------------->|
| | |
| | AA-Answer|
| Result-Code=DIAMETER_MULTI_ROUND_AUTH|
| NASREQ-Payload(NASREQ Request #1)|
| |<-----------------------------+
| | |
| Request | |
|<-----------------+ |
| | |
: : :
: <<<more message exchanges>>> :
: : :
| Response #N | |
+----------------->| |
| | |
| |AA-Request |
| |NASREQ-Payload ( Response #N )|
| +----------------------------->|
| | |
| | AA-Answer|
| | Result-Code=DIAMETER_SUCCESS|
| | (authorization AVPs)|
| |QoS-Resources(QoS-Authorized) |
| |<-----------------------------+
| | |
| Success | |
|<-----------------+ |
| | |
| Figure 3: Example of a Diameter NASREQ enhanced with QoS Information |
| TOC |
Figure 4 (Example of an Authorization-Only Message Flow) shows an example of authorization only QoS signaling as part of the NASREQ message exchange. The NAS provides the Diameter server with the "QoS-Desired" QoS-Semantics AVP included in the QoS-Resources AVP. The Diameter server then either authorizes the indicated QoS or rejects the request and informs the NAS about the result. In this scenario the NAS does not need to include the QoS-Capability AVP in the AAR message as the QoS-Resources AVP implicitly does the same and also the NAS is authorizing a specific QoS profile, not a pre-provisioned one.
End Diameter
Host NAS Server
| | |
| | |
| QoS Request | |
+----------------->| |
| | |
| |AA-Request |
| |Auth-Request-Type=AUTHORIZE_ONLY
| |NASREQ-Payload |
| |QoS-Resources(QoS-Desired) |
| +----------------------------->|
| | |
| | AA-Answer|
| | NASREQ-Payload(Success)|
| | QoS-Resources(QoS-Authorized)|
| |<-----------------------------+
| Accept | |
|<-----------------+ |
| | |
| | |
| | |
| Figure 4: Example of an Authorization-Only Message Flow |
| TOC |
Figure 5 (Example of a Server-initiated Re-Authorization Procedure) shows a message exchange for a Diameter server initiated QoS re-authorization procedure. The Diameter server sends the NAS a RAR message requesting re-authorization for an existing session and the NAS acknowledges it with a RAA message. The NAS is aware of its existing QoS profile and information for the ongoing session that the Diameter server requested for re-authorization. Thus, the NAS must initiate re-authorization of the existing QoS profile. The re-authorization procedure is the same as in Figure 4 (Example of an Authorization-Only Message Flow).
End Diameter
Host NAS Server
| | |
| | |
: : :
: <<<Initial Message Exchanges>>> :
: : :
| | |
| | RA-Request |
| |<-----------------------------+
| | |
| |RA-Answer |
| |Result-Code=DIAMETER_SUCCESS |
| +----------------------------->|
| | |
| | |
| |AA-Request |
| |NASREQ-Payload |
| |Auth-Request-Type=AUTHORIZE_ONLY
| |QoS-Resources(QoS-Desired) |
| +----------------------------->|
| | |
| | AA-Answer|
| | Result-Code=DIAMETER_SUCCESS|
| | (authorization AVPs)|
| | QoS-Resources(QoS-Authorized)|
| |<-----------------------------+
| | |
| Figure 5: Example of a Server-initiated Re-Authorization Procedure |
| TOC |
In this case the User is charged as soon as the Service Element (CC client) receives
the service request. In this case the client uses the "QoS-Desired" QoS-Semantics
parameter in the QoS-Resources AVP that it sends to the Accounitng server. The server
responds with a "QoS-Available" QoS-Semantics parameter in the QoS-Resources AVP
Service Element
End User (CC Client) B CC Server
| | | |
|(1) Service Request | | |
|-------------------->| | |
| |(2) CCR (event, DIRECT_DEBITING,|
| | QoS-Resources[QoS-desired]) |
| |-------------------------------->|
| |(3) CCA (Granted-Units, QoS- |
| | Resources[QoS-Authorized]) |
| |<--------------------------------|
|(4) Service Delivery | | |
|<--------------------| | |
|(5) Begin service | | |
|<------------------------------------>| |
| | | |
. . . .
. . . .
| Figure 6: Example for a One-Time Diameter Credit Control Charging Event |
| TOC |
Example: Classify all packets from hosts on subnet 12.34.56.00/24 to ports 80, 8090 or 443 on web servers 23.45.67.123, 23.45.68.124, 23.45.69.125.
Classifier = {
Classifier-Id = "web_svr_example";
Protocol = TCP;
Direction = OUT;
From-Spec = {
IP-Address-Mask = {
IP-Address = 12.34.56.00;
IP-Bit-Mask-Width = 24;
}
}
To-Spec = {
IP-Address = 23.45.67.123;
IP-Address = 23.45.68.124;
IP-Address = 23.45.69.125;
Port = 80;
Port = 8080;
Port = 443;
}
}
Example: Any SIP signalling traffic from a device with a MAC address of 01:23:45:67:89:ab to servers with IP addresses in the range 34.56.78.90 to 34.56.78.190.
Classifier = {
Classifier-Id = "web_svr_example";
Protocol = UDP;
Direction = OUT;
From-Spec = {
MAC-Address = 01:23:45:67:89:ab;
}
To-Spec = {
IP-Address-Range = {
IP-Address-Start = 34.56.78.90;
IP-Address-End = 34.56.78.190;
}
Port = 5060;
Port = 3478;
Port-Range = {
Port-Start = 16348;
Port-End = 32768;
}
}
}
| TOC |
We would like to thank Victor Fajardo, Tseno Tsenov, Robert Hancock, Jukka Manner, Cornelia Kappler, Xiaoming Fu, Frank Alfano,Tolga Asveren, Mike Montemurro, Glen Zorn, Avri Doria, Dong Sun, Tina Tsou, Pete McCann, Georgios Karagiannis, Elwyn Davies, Max Riegel and Yong Li for their comments.
| TOC |
Max Riegel contributed the VLAN sections.
| TOC |
IANA is requested to allocate AVP codes for the following AVPs that are defined in this document.
+------------------------------------------------------------------+ | AVP Section | | Attribute Name Code Defined Data Type | +------------------------------------------------------------------+ |QoS-Capability TBD 3.1 Grouped | |QoS-Profile-Template TBD 3.2 Unsigned32 | |Vendor-Specific-QoS-Profile-Template TBD 3.3 Grouped | |Extended-QoS-Filter-Rule TBD 3.5 Grouped | |QoS-Semantics TBD 3.6 Enumerated | |QoS-Parameters TBD 3.7 OctetString | |QoS-Rule-Precedence TBD 3.8 Unsigned32 | |Classifier TBD 5.1 Grouped | |Classifier-ID TBD 5.2 OctetString | |Protocol TBD 5.3 Enumerated | |Direction TBD 5.4 Enumerated | |From-Spec TBD 5.5 Grouped | |To-Spec TBD 5.6 Grouped | |Negated TBD 5.7.1 Enumerated | |IP-Address TBD 5.7.2 Address | |IP-Address-Range TBD 5.7.3 Grouped | |IP-Address-Start TBD 5.7.4 Address | |IP-Address-End TBD 5.7.5 Address | |IP-Address-Mask TBD 5.7.6 Grouped | |IP-Mask-Bit-Mask-Width TBD 5.7.7 OctetString | |MAC-Address TBD 5.7.8 OctetString | |MAC-Address-Mask TBD 5.7.9 Grouped | |MAC-Address-Mask-Pattern TBD 5.7.10 OctetString | |EUI64-Address TBD 5.7.11 OctetString | |EUI64-Address-Mask TBD 5.7.12 Grouped | |EUI64-Address-Mask-Pattern TBD 5.7.13 OctetString | |Port TBD 5.7.14 Integer32 | |Port-Range TBD 5.7.15 Grouped | |Port-Start TBD 5.7.16 Integer32 | |Port-End TBD 5.7.17 Integer32 | |Use-Assigned-Address TBD 5.7.18 Enumerated | |Diffserv-Code-Point TBD 5.8.1 Enumerated | |Fragmentation-Flag TBD 5.8.2 Enumerated | |IP-Option TBD 5.8.3 Grouped | |IP-Option-Type TBD 5.8.4 Enumerated | |IP-Option-Value TBD 5.8.5 OctetString | |TCP-Option TBD 5.8.6 Grouped | |TCP-Option-Type TBD 5.8.7 Enumerated | |TCP-Option-Value TBD 5.8.8 OctetString | |TCP-Flags TBD 5.8.9 Grouped | |TCP-Flag-Type TBD 5.8.10 Enumerated | |ICMP-Type TBD 5.8.11 Grouped | |ICMP-Type-Number TBD 5.8.12 Enumerated | |ICMP-Code TBD 5.8.13 Enumerated | |ETH-Option TBD 5.8.14 Grouped | |ETH-Proto-Type TBD 5.8.15 Grouped | |ETH-Ether-Type TBD 5.8.16 OctetString | |ETH-SAP TBD 5.8.17 OctetString | |VLAN-ID-Range TBD 5.8.18 Grouped | |S-VID-Start TBD 5.8.19 Unsigned32 | |S-VID-End TBD 5.8.20 Unsigned32 | |C-VID-Start TBD 5.8.21 Unsigned32 | |C-VID-End TBD 5.8.22 Unsigned32 | |ETH-Priority-Range TBD 5.8.23 Grouped | |ETH-Low-Priority TBD 5.8.24 Unsigned32 | |ETH-High-Priority TBD 5.8.25 Unsigned32 | |Time-Of-Day-Condition TBD 6.1 Grouped | |Time-Of-Day-Start TBD 6.2 Grouped | |Time-Of-Day-End TBD 6.3 Unsigned32 | |Day-Of-Week-Mask TBD 6.4 Unsigned32 | |Day-Of-Month-Mask TBD 6.5 Unsigned32 | |Month-Of-Year-Mask TBD 6.6 Unsigned32 | |Absolute-Start-Time TBD 6.7 Time | |Absolute-End-Time TBD 6.8 Time | |Timezone-Flag TBD 6.9 Enumerated | |Timezone-Offset TBD 6.10 Integer32 | +------------------------------------------------------------------+
IANA is also requested to allocate a registry for the QoS-Semantics. The following values are allocated by this specification.
(0): QoS-Desired
(1): QoS-Available
(2): QoS-Reserved
(3): Minimum-QoS
(4): QoS-Authorized
A specification is required to add a new value to the registry. A standards track document is required to depreciate, delete, or modify existing values.
| TOC |
This document describes the extension of Diameter for conveying Quality of Service information. The security considerations of the Diameter protocol itself have been discussed in RFC 3588bis [I‑D.ietf‑dime‑rfc3588bis] (Fajardo, V., Arkko, J., Loughney, J., and G. Zorn, “Diameter Base Protocol,” April 2010.). Use of the AVPs defined in this document MUST take into consideration the security issues and requirements of the Diameter Base protocol.
| TOC |
| TOC |
| [DSCP] | IANA, “Differentiated Services Field Codepoints,” http://www.iana.org/assignments/dscp-registry. |
| [I-D.ietf-dime-qos-parameters] | Korhonen, J., Tschofenig, H., and E. Davies, “Quality of Service Parameters for Usage with Diameter,” draft-ietf-dime-qos-parameters-11 (work in progress), May 2009 (TXT). |
| [I-D.ietf-dime-rfc3588bis] | Fajardo, V., Arkko, J., Loughney, J., and G. Zorn, “Diameter Base Protocol,” draft-ietf-dime-rfc3588bis-20 (work in progress), April 2010 (TXT). |
| [ICMPTYPE] | IANA, “ICMP Type Numbers,” http://www.iana.org/assignments/icmp-parameters. |
| [IEEE802.1D] | IEEE, “IEEE Standard for Local and metropolitan area networks, Media Access Control (MAC) Bridges,” 2004. |
| [IEEE802.1Q] | IEEE, “IEEE Standard for Local and metropolitan area networks, Virtual Bridged Local Area Networks,” 2005. |
| [IEEE802.1ad] | IEEE, “IEEE Standard for Local and metropolitan area networks, Virtual Bridged Local Area Networks, Amendment 4: Provider Bridges,” 2005. |
| [IEEE802.2] | IEEE, “IEEE Standard for Information technology, Telecommunications and information exchange between systems, Local and metropolitan area networks, Specific requirements, Part 2: Logical Link Control,” 1998. |
| [IPOPTIONS] | IANA, “IP Option Numbers,” http://www.iana.org/assignments/ip-parameters. |
| [PROTOCOL] | IANA, “Protocol Types,” http://www.iana.org/assignments/protocol-numbers. |
| [RFC2119] | Bradner, S., “Key words for use in RFCs to Indicate Requirement Levels,” BCP 14, RFC 2119, March 1997 (TXT, HTML, XML). |
| [RFC4005] | Calhoun, P., Zorn, G., Spence, D., and D. Mitton, “Diameter Network Access Server Application,” RFC 4005, August 2005 (TXT). |
| [TCPOPTIONS] | IANA, “TCP Option Numbers,” http://www.iana.org/assignments/tcp-parameters. |
| TOC |
| [I-D.ietf-dime-diameter-qos] | Sun, D., McCann, P., Tschofenig, H., ZOU), T., Doria, A., and G. Zorn, “Diameter Quality of Service Application,” draft-ietf-dime-diameter-qos-15 (work in progress), March 2010 (TXT). |
| TOC |
| Jouni Korhonen | |
| TeliaSonera | |
| Teollisuuskatu 13 | |
| Sonera FIN-00051 | |
| Finland | |
| Email: | jouni.korhonen@teliasonera.com |
| Hannes Tschofenig | |
| Nokia Siemens Networks | |
| Linnoitustie 6 | |
| Espoo 02600 | |
| Finland | |
| Phone: | +358 (50) 4871445 |
| Email: | Hannes.Tschofenig@gmx.net |
| URI: | http://www.tschofenig.priv.at |
| Mayutan Arumaithurai | |
| University of Goettingen | |
| Email: | mayutan.arumaithurai@gmail.com |
| Mark Jones (editor) | |
| Bridgewater Systems | |
| 303 Terry Fox Drive, Suite 500 | |
| Ottawa, Ontario K2K 3J1 | |
| Canada | |
| Phone: | +1 613-591-6655 |
| Email: | mark.jones@bridgewatersystems.com |
| Avi Lior | |
| Bridgewater Systems | |
| 303 Terry Fox Drive, Suite 500 | |
| Ottawa, Ontario K2K 3J1 | |
| Canada | |
| Phone: | +1 613-591-6655 |
| Email: | avi@bridgewatersystems.com |
| TOC |
Copyright © The IETF Trust (2008).
This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights.
This document and the information contained herein are provided on an “AS IS” basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org.