BGP Next-Hop dependent capabilities
draft-ietf-idr-next-hop-capability-02

Abstract

RFC 5492 advertises the capabilities of the BGP peer. When the BGP peer is not the same as the BGP Next-Hop, it is useful to also be able to advertise the capability of the BGP Next-Hop, in particular to advertise forwarding plane features. This document defines a mechanism to advertise such BGP Next Hop dependent Capabilities.

This document defines a new BGP non-transitive attribute to carry Next-Hop Capabilities. This attribute is guaranteed to be deleted or updated when the BGP Next Hop is changed, in order to reflect the capabilities of the new BGP Next-Hop.

This document also defines a Next-Hop capability to advertise the ability to process the MPLS Entropy Label as an egress LSR for all NLRI advertised in the BGP UPDATE. It updates RFC 6790 with regard to this BGP signaling.

Requirements Language

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on August 16, 2018.

Copyright Notice

Copyright (c) 2018 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.

Table of Contents

• 1. Introduction
• 2. BGP Next-Hop dependent Capabilities Attribute
• 2.1. Encoding
• 2.2. Attribute Operation
• 2.3. Interpreting received Capability
• 2.4. Attribute Error Handling
• 2.5. Network operation considerations
• 3. Entropy Label Next-Hop dependent Capability
• 3.1. Entropy Label Next-Hop Capability error handling
• 4. IANA Considerations
• 4.1. Next-Hop Capabilities Attribute
• 4.2. Next-Hop Capability registry
• 5. Security Considerations
• 6. Acknowledgement
• 7. References
• 7.1. Normative References
• 7.2. Informative References
• Appendix A. Changes / Author Notes
• Authors' Addresses

1. Introduction

[RFC5492] advertises the capabilities of the BGP peer. When the BGP peer is not the same as the BGP Next-Hop, it is useful to also be able to advertise the capability of the BGP Next-Hop, in particular to advertise forwarding plane features. This document defines a mechanism to advertise such BGP Next Hop Capabilities.

This document defines a new BGP non-transitive attribute to carry Next-Hop Capabilities. This attribute is guaranteed to be deleted or updated when the BGP Next Hop is changed, in order to reflect the capabilities of the new BGP Next-Hop. Hence it allows advertising capabilities which are dependent of the BGP Next-Hop.

This attribute advertises the capabilities of the BGP Next-Hop for the NLRI advertised in the same BGP update. A BGP Next-Hop may advertise different capabilities for different set of NLRI.

This document also defines a first application to advertise the capability to handle the MPLS Entropy Label defined in [RFC6790]. Note that RFC 6790 had originally defined a BGP attribute for this but it has been latter deprecated in [RFC7447].

2. BGP Next-Hop dependent Capabilities Attribute

2.1. Encoding

The BGP Next-Hop dependent Capabilities Attribute is an optional, non-transitive BGP Attribute, of value TBD1. The attribute consists of a set of Next-Hop Capabilities.

The inclusion of a Next-Hop Capability "X" in a BGP UPDATE message, indicates that the BGP Next-Hop, encoded in either the NEXT_HOP attribute defined in [RFC4271] or the Network Address of Next Hop field of the MP_REACH_NLRI attribute defined in [RFC4760], supports the capability "X" for the NLRI advertised in this BGP UPDATE.

This document does not make a distinction between these two Next-Hop fields and uses the term 'BGP Next-Hop' to refer to whichever one is used in a given BGP UPDATE message.

A Next-Hop Capability is a triple (Capability Code, Capability Length, Capability Value) aka a TLV:

+------------------------------+
| Capability Code (2 octets)   |
+------------------------------+
| Capability Length (2 octets) |
+------------------------------+
| Capability Value (variable)  |
~                              ~
+------------------------------+

Figure 1: BGP Next-Hop Capability

Capability Code: a two-octets unsigned binary integer which indicates the type of "Next-Hop Capability" advertised and unambiguously identifies an individual capability.

Capability Length: a two-octets unsigned binary integer which indicates the length, in octets, of the Capability Value field. A length of 0 indicates that no Capability Value field is present.

Capability Value: a variable-length field. It is interpreted according to the value of the Capability Code.

BGP speakers SHOULD NOT include more than one instance of a Next-Hop capability with the same Capability Code, Capability Length, and Capability Value. Note, however, that processing of multiple instances of such capability does not require special handling, as additional instances do not change the meaning of the announced capability; thus, a BGP speaker MUST be prepared to accept such multiple instances.

BGP speakers MAY include more than one instance of a capability (as identified by the Capability Code) with non-zero Capability Length field, but with different Capability Value and either the same or different Capability Length. Processing of these capability instances is specific to the Capability Code and MUST be described in the document introducing the new capability.

2.2. Attribute Operation

The BGP Next-Hop dependent Capabilities attribute being non-transitive, as per [RFC4271], a BGP speaker which does not understand it will quietly ignore it and not pass it along to other BGP peers.

A BGP speaker that understands the BGP Next-Hop dependent Capabilities Attribute and does not change the BGP Next-Hop, SHOULD NOT change the BGP Next-Hop dependent Capabilities Attribute and SHOULD pass the attribute unchanged along to other BGP peers.

A BGP speaker that understands the BGP Next-Hop dependent Capabilities Attribute and changes the BGP Next-Hop, MUST remove or update the received BGP Next-Hop dependent Capabilities Attribute before propagating the BGP UPDATE to other BGP peers. If the capability is not removed, it MUST be updated to only advertise the capabilities of the new BGP Next-Hop for these NLRIs. An implementation MAY allow, by configuration, to not advertise some of the capabilities of a BGP Next-Hop. If a received capability is unknown, it can't be updated hence unknown capabilities MUST be removed when the BGP Next-Hop is changed.

The BGP Next-Hop Capability Code MUST reflect the capability of the router indicated in the BGP Next-Hop, for the NLRI advertised in the BGP UPDATE. If a BGP speaker sets the BGP Next-Hop to an address of a different router, it MUST NOT advertise a BGP Next-Hop Capability not supported by this router for these NLRI.

2.3. Interpreting received Capability

A BGP speaker receiving a BGP Next-Hop Capability Code that it supports behave as defined in the document defining this Capability Code. A BGP speaker receiving a BGP Next-Hop Capability Code that it does not support MUST ignore this BGP Next-Hop Capability Code. In particular, this MUST NOT be handled as an error. In both cases, the BGP speaker MUST examine the remaining BGP Next-Hop Capability Code(s) that may be present in the BGP Next-Hop Capabilities Attribute.

The presence of a Next-Hop Capability SHOULD NOT influence route selection or route preference, unless tunneling is used to reach the BGP Next-Hop or the selected route has been learnt from EBGP (i.e. the Next-Hop is in a different AS). Indeed, it is in general impossible for a node to know that all BGP routers of the Autonomous System (AS) will understand a given Next-Hop Capability; and having different routers, within an AS, use a different preference for a route, may result in forwarding loops if tunnelling is not used to reach the BGP Next-Hop.

2.4. Attribute Error Handling

A BGP Next-Hop dependent Capabilities Attribute is considered malformed if the length of the Attribute is not equal to the sum of all (BGP Next-Hop dependent Capability Length +4) of the capabilities carried in this attribute. Note that "4" is the length of the fields "Type" and "Length" of each BGP Next Hop dependent Capability, as the capability length only account for the length of the Value field.

A BGP UPDATE message with a malformed BGP Next-Hop dependent Capabilities Attribute SHALL be handled using the approach of "attribute discard" defined in [RFC7606].

Unknown Next-Hop Capabilities Codes MUST NOT be considered as an error.

A document that specifies a new Next-Hop Capability SHOULD provide specifics regarding what constitutes an error for that Next-Hop Capability.

If a Next-Hop dependent Capability is malformed, this Capability MUST be ignored and removed. Others Next-Hop Capabilities MUST be processed as usual.

2.5. Network operation considerations

In the corner case where multiple nodes use the same IP address as their BGP Next-Hop, aka anycast nodes as described in [RFC4786], a BGP speaker MUST NOT advertise a given Next-Hop Capability unless all nodes sharing this same IP address support this Next-Hop Capability. The network operator operating those anycast nodes is responsible for enforcing that an anycast node does not advertise a BGP Next-Hop capability not supported by all nodes advertising this anycast address. This can be performed by using anycast nodes sharing the same capabilities or by filtering the BGP Next-Hop Capabilities which are not shared by all anycast nodes.

For security considerations, a network operator may want to filter the BGP Next-Hop capabilities advertised to external Autonomous Systems.

3. Entropy Label Next-Hop dependent Capability

The Entropy Label Next-Hop Capability has type code 1 and a length of 0 octet.

The inclusion of the "Entropy Label" Next-Hop Capability indicates that the BGP Next-Hop can be sent packets, for all routes indicated in the NRLI, with a MPLS entropy label (ELI, EL) added immediately after the label stack advertised with the NLRI.

On the receiving side, suppose BGP speaker S has determined that packet P is to be forwarded according to BGP route R, where R is a route of one of the labeled address families. And suppose that L is the label stack embedded in the NLRI of route R. Then to forward packet P according to route R, S either replaces P's top label with L, or else pushes L onto the MPLS label stack. If the EL-Capability is advertised in the BGP UPDATE advertising this route R, S knows that it may safely place the ELI and an EL on the label stack immediately beneath L.

A BGP speaker S that sends an UPDATE with the BGP Next-Hop "NH" MAY include the Entropy Label Next-Hop Capability only if the NLRI are labelled and for all the NLRI in the BGP UPDATE, either of the following is true:

• Egress case: NH is the egress of the LSP advertised with the NLRI and its capable of handling the ELI during the lookup of the MPLS top label.
• Transit LSR case: NH is a transit LSR for the LSP advertised with the NLRI (i.e. NH swaps one of the label advertised in the NLRI) and next downstream BGP Next-Hop(s) has(have) advertised the Entropy Label Next-Hop Capability (or a similar capability signalled by protocol P if the route is redistributed, by NH, from protocol P into BGP).

3.1. Entropy Label Next-Hop Capability error handling

If the Entropy Label Next-Hop Capability is present more than once, it MUST be considered as received once with a length of 0.

If the Entropy Label Next-Hop Capability is received with a length other than 0, it is not considered malformed, but its semantics are exactly the same as if it had a length of 0. In other words, additional octets MUST be ignored. This is to allow for graceful future extension.

4. IANA Considerations

4.1. Next-Hop Capabilities Attribute

IANA is requested to allocate a new Path Attribute, called "Next-Hop Capabilities", type Code TBD1, from the "BGP Path Attributes" registry.

4.2. Next-Hop Capability registry

The IANA is requested to create and maintain a registry entitled "BGP Next-Hop Capabilities".

The registration policies [RFC8126] for this registry are:

 
     1-63   IETF Review
 64-65534   First Come First Served
    65535   Reserved
  

IANA is requested to make the following initial assignments:

 
            Registry Name: Next-Hop Capability.

 Value      Meaning                                  Reference
 ---------- ---------------------------------------- ---------
       0    Reserved  (not to be allocated)          This document
       1    Entropy Label                            This document
 2-65534    Unassigned
   65535    Reserved for future registry extension   This document
       

5. Security Considerations

This document does not introduce new security vulnerabilities in BGP. Specifically, an operator who is relying on the information carried in BGP must have a transitive trust relationship back to the source of the information. Specifying the mechanism(s) to provide such a relationship is beyond the scope of this document. Please refer to the Security Considerations section of [RFC4271] for security mechanisms applicable to BGP.

The advertisement of BGP Next-Hop capabilities to EBGP peers may disclose, to the peer AS, some capabilities of the BGP node and may help fingerprinting its hardware model and software version. This may be mitigated by filtering the capability advertised to EBGP peers.

Security of the Entropy Label capability advertisement is unchanged compared to [RFC6790] which first defined this signaling.

6. Acknowledgement

The Entropy Label Next-Hop Capability defined in this document is based on the ELC BGP attribute defined in section 5.2 of [RFC6790].

The authors wish to thank John Scudder for the discussions on this topic and Eric Rosen for his in-depth review of this document.

The authors wish to thank Jie Dong and Robert Raszuk for their review and comments.

7. References

7.1. Normative References

7.2. Informative References

Appendix A. Changes / Author Notes

[RFC Editor: Please remove this section before publication]

Changes -01:

• Capability code and length encoded over 2 octets (from one). IANA registry is now mainly FCFS.
• Addition of section "Network operation considerations", in particular to discuss anycast nodes.
• Enhanced Security consideration (capability advertised to external ASes).
• Editorial changes and typo corrections.

Changes -02: No change. Refresh only.

Authors' Addresses