| Network Working Group | A. Morton |
| Internet-Draft | AT&T Labs |
| Intended status: Standards Track | M. Bagnulo |
| Expires: September 10, 2020 | UC3M |
| P. Eardley | |
| BT | |
| K. D'Souza | |
| AT&T Labs | |
| March 9, 2020 |
Initial Performance Metrics Registry Entries
draft-ietf-ippm-initial-registry-16
This memo defines the set of Initial Entries for the IANA Performance Metrics Registry. The set includes: UDP Round-trip Latency and Loss, Packet Delay Variation, DNS Response Latency and Loss, UDP Poisson One-way Delay and Loss, UDP Periodic One-way Delay and Loss, ICMP Round-trip Latency and Loss, and TCP round-trip Latency and Loss.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14[RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."
This Internet-Draft will expire on September 10, 2020.
Copyright (c) 2020 IETF Trust and the persons identified as the document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.
This memo proposes an initial set of entries for the Performance Metrics Registry. It uses terms and definitions from the IPPM literature, primarily [RFC2330].
Although there are several standard templates for organizing specifications of performance metrics (see [RFC7679] for an example of the traditional IPPM template, based to large extent on the Benchmarking Methodology Working Group's traditional template in [RFC1242], and see [RFC6390] for a similar template), none of these templates were intended to become the basis for the columns of an IETF-wide registry of metrics. While examining aspects of metric specifications which need to be registered, it became clear that none of the existing metric templates fully satisfies the particular needs of a registry.
Therefore, [I-D.ietf-ippm-metric-registry] defines the overall format for a Performance Metrics Registry. Section 5 of [I-D.ietf-ippm-metric-registry] also gives guidelines for those requesting registration of a Metric, that is the creation of entry(s) in the Performance Metrics Registry: "In essence, there needs to be evidence that a candidate Registered Performance Metric has significant industry interest, or has seen deployment, and there is agreement that the candidate Registered Performance Metric serves its intended purpose." The process in [I-D.ietf-ippm-metric-registry] also requires that new entries are administered by IANA through Specification Required policy, which will ensure that the metrics are tightly defined.
This document defines a set of initial Performance Metrics Registry entries. Most are Active Performance Metrics, which are based on RFCs prepared in the IPPM working group of the IETF, according to their framework [RFC2330] and its updates.
This memo uses the terminology defined in [I-D.ietf-ippm-metric-registry].
This section provides the categories and columns of the registry, for easy reference. An entry (row) therefore gives a complete description of a Registered Metric.
Legend:
Registry Categories and Columns, shown as
Category
------------------
Column | Column |
Summary
------------------------------------------------------------------------
Identifier | Name | URI | Desc. | Reference | Change Controller | Ver |
Metric Definition
-----------------------------------------
Reference Definition | Fixed Parameters |
Method of Measurement
---------------------------------------------------------------------
Reference | Packet | Traffic | Sampling | Run-time | Role |
Method | Stream | Filter | Distribution | Parameters | |
| Generation |
Output
-----------------------------------------
Type | Reference | Units | Calibration |
| Definition | | |
Administrative Information
------------------------------------
Status |Requester | Rev | Rev.Date |
Comments and Remarks
--------------------
This section specifies an initial registry entry for the UDP Round-trip Latency, and another entry for UDP Round-trip Loss Ratio.
Note: Each Registry entry only produces a "raw" output or a statistical summary. To describe both "raw" and one or more statistics efficiently, the Identifier, Name, and Output Categories can be split and a single section can specify two or more closely-related metrics. For example, this section specifies two Registry entries with many common columns. See Section 7 for an example specifying multiple Registry entries with many common columns.
All column entries beside the ID, Name, Description, and Output Reference Method categories are the same, thus this section proposes two closely-related registry entries. As a result, IANA is also asked to assign a corresponding URL to each Named Metric.
This category includes multiple indexes to the registry entry: the element ID and metric name.
IANA is asked to assign different numeric identifiers to each of the two Named Metrics.
RTDelay_Active_IP-UDP-Periodic_RFCXXXXsec4_Seconds_95Percentile
RTLoss_Active_IP-UDP-Periodic_RFCXXXXsec4_Percent_LossRatio
URL: https://www.iana.org/ ... <name>
RTDelay: This metric assesses the delay of a stream of packets exchanged between two hosts (which are the two measurement points), and the Output is the Round-trip delay for all successfully exchanged packets expressed as the 95th percentile of their conditional delay distribution.
RTLoss: This metric assesses the loss ratio of a stream of packets exchanged between two hosts (which are the two measurement points), and the Output is the Round-trip loss ratio for all successfully exchanged packets expressed as a percentage.
IETF
1.0
This category includes columns to prompt the entry of all necessary details related to the metric definition, including the RFC reference and values of input factors, called fixed parameters.
Almes, G., Kalidindi, S., and M. Zekauskas, "A Round-trip Delay Metric for IPPM", RFC 2681, September 1999.
Section 2.4 of [RFC2681] provides the reference definition of the singleton (single value) Round-trip delay metric. Section 3.4 of [RFC2681] provides the reference definition expanded to cover a multi-singleton sample. Note that terms such as singleton and sample are defined in Section 11 of [RFC2330].
Note that although the [RFC2681] definition of "Round-trip-Delay between Src and Dst" is directionally ambiguous in the text, this metric tightens the definition further to recognize that the host in the "Src" role will send the first packet to "Dst", and ultimately receive the corresponding return packet from "Dst" (when neither are lost).
Finally, note that the variable "dT" is used in [RFC2681] to refer to the value of Round-trip delay in metric definitions and methods. The variable "dT" has been re-used in other IPPM literature to refer to different quantities, and cannot be used as a global variable name.
Morton, A., "Round-trip Packet Loss Metrics", RFC 6673, August 2012.
Both delay and loss metrics employ a maximum waiting time for received packets, so the count of lost packets to total packets sent is the basis for the loss ratio calculation as per Section 6.1 of [RFC6673].
Type-P as defined in Section 13 of [RFC2330]:
Other measurement parameters:
This category includes columns for references to relevant sections of the RFC(s) and any supplemental information needed to ensure an unambiguous methods for implementations.
The methodology for this metric is defined as Type-P-Round-trip-Delay-Poisson-Stream in section 2.6 of RFC 2681 and section 3.6 of RFC 2681 using the Type-P and Tmax defined under Fixed Parameters. However, the Periodic stream will be generated according to [RFC3432].
The reference method distinguishes between long-delayed packets and lost packets by implementing a maximum waiting time for packet arrival. Tmax is the waiting time used as the threshold to declare a packet lost. Lost packets SHALL be designated as having undefined delay, and counted for the RTLoss metric.
The calculations on the delay (RTT) SHALL be performed on the conditional distribution, conditioned on successful packet arrival within Tmax. Also, when all packet delays are stored, the process which calculates the RTT value MUST enforce the Tmax threshold on stored values before calculations. See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
The reference method requires some way to distinguish between different packets in a stream to establish correspondence between sending times and receiving times for each successfully-arriving packet. Sequence numbers or other send-order identification MUST be retained at the Src or included with each packet to disambiguate packet reordering if it occurs.
If a standard measurement protocol is employed, then the measurement process will determine the sequence numbers or timestamps applied to test packets after the Fixed and Runtime parameters are passed to that process. The chosen measurement protocol will dictate the format of sequence numbers and time-stamps, if they are conveyed in the packet payload.
Refer to Section 4.4 of [RFC6673] for expanded discussion of the instruction to "send a Type-P packet back to the Src as quickly as possible" in Section 2.6 of RFC 2681. Section 8 of [RFC6673] presents additional requirements which MUST be included in the method of measurement for this metric.
This section gives the details of the packet traffic which is the basis for measurement. In IPPM metrics, this is called the Stream, and can easily be described by providing the list of stream parameters.
Section 3 of [RFC3432] prescribes the method for generating Periodic streams using associated parameters.
NOTE: an initiation process with a number of control exchanges resulting in unpredictable start times (within a time interval) may be sufficient to avoid synchronization of periodic streams, and therefore a valid replacement for selecting a start time at random from a fixed interval.
The T0 parameter will be reported as a measured parameter. Parameters incT and dT are Fixed Parameters.
NA
NA
Run-time Parameters are input factors that must be determined, configured into the measurement system, and reported with the results for the context to be complete.
This category specifies all details of the Output of measurements using the metric.
Percentile -- for the conditional distribution of all packets with a valid value of Round-trip delay (undefined delays are excluded), a single value corresponding to the 95th percentile, as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
The percentile = 95, meaning that the reported delay, "95Percentile", is the smallest value of Round-trip delay for which the Empirical Distribution Function (EDF), F(95Percentile) >= 95% of the singleton Round-trip delay values in the conditional distribution. See section 11.3 of [RFC2330] for the definition of the percentile statistic using the EDF.
LossRatio -- the count of lost packets to total packets sent is the basis for the loss ratio calculation as per Section 6.1 of [RFC6673].
For all outputs ---
For
RTDelay_Active_IP-UDP-Periodic_RFCXXXXsec4_Seconds_95Percentile:
For
RTLoss_Active_IP-UDP-Periodic_RFCXXXXsec4_Percent_LossRatio:
The 95th Percentile of Round-trip Delay is expressed in seconds.
The Round-trip Loss Ratio is expressed as a percentage of lost packets to total packets sent.
Section 3.7.3 of [RFC7679] provides a means to quantify the systematic and random errors of a time measurement. In-situ calibration could be enabled with an internal loopback at the Source host that includes as much of the measurement system as possible, performs address manipulation as needed, and provides some form of isolation (e.g., deterministic delay) to avoid send-receive interface contention. Some portion of the random and systematic error can be characterized this way.
When a measurement controller requests a calibration measurement, the loopback is applied and the result is output in the same format as a normal measurement with additional indication that it is a calibration result.
Both internal loopback calibration and clock synchronization can be used to estimate the available accuracy of the Output Metric Units. For example, repeated loopback delay measurements will reveal the portion of the Output result resolution which is the result of system noise, and thus inaccurate.
Current
This RFC number
1.0
YYYY-MM-DD
None.
This section gives an initial registry entry for a Packet Delay Variation metric.
This category includes multiple indexes to the registry entries, the element ID and metric name.
<insert numeric identifier, an integer>
OWPDV_Active_IP-UDP-Periodic_RFCXXXXsec5_Seconds_95Percentile
URL: https://www.iana.org/ ... <name>
An assessment of packet delay variation with respect to the minimum delay observed on the periodic stream, and the Output is expressed as the 95th percentile of the packet delay variation distribution.
IETF
1.0
This category includes columns to prompt the entry of all necessary details related to the metric definition, including the RFC reference and values of input factors, called fixed parameters.
Paxson, V., Almes, G., Mahdavi, J., and M. Mathis, "Framework for IP Performance Metrics", RFC 2330, May 1998. [RFC2330]
Demichelis, C. and P. Chimento, "IP Packet Delay Variation Metric for IP Performance Metrics (IPPM)", RFC 3393, November 2002. [RFC3393]
Morton, A. and B. Claise, "Packet Delay Variation Applicability Statement", RFC 5481, March 2009. [RFC5481]
Mills, D., Martin, J., Burbank, J., and W. Kasch, "Network Time Protocol Version 4: Protocol and Algorithms Specification", RFC 5905, June 2010.[RFC5905]
See sections 2.4 and 3.4 of [RFC3393]. Singleton delay differences measured are referred to by the variable name "ddT" (applicable to all forms of delay variation). However, this metric entry specifies the PDV form defined in section 4.2 of [RFC5481], where the singleton PDV for packet i is referred to by the variable name "PDV(i)".
Other measurement parameters:
See the Packet Stream generation category for two additional Fixed Parameters.
This category includes columns for references to relevant sections of the RFC(s) and any supplemental information needed to ensure an unambiguous methods for implementations.
See section 2.6 and 3.6 of [RFC3393] for general singleton element calculations. This metric entry requires implementation of the PDV form defined in section 4.2 of [RFC5481]. Also see measurement considerations in section 8 of [RFC5481].
The reference method distinguishes between long-delayed packets and lost packets by implementing a maximum waiting time for packet arrival. Tmax is the waiting time used as the threshold to declare a packet lost. Lost packets SHALL be designated as having undefined delay.
The calculations on the one-way delay SHALL be performed on the conditional distribution, conditioned on successful packet arrival within Tmax. Also, when all packet delays are stored, the process which calculates the one-way delay value MUST enforce the Tmax threshold on stored values before calculations. See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
The reference method requires some way to distinguish between different packets in a stream to establish correspondence between sending times and receiving times for each successfully-arriving packet. Sequence numbers or other send-order identification MUST be retained at the Src or included with each packet to disambiguate packet reordering if it occurs.
If a standard measurement protocol is employed, then the measurement process will determine the sequence numbers or timestamps applied to test packets after the Fixed and Runtime parameters are passed to that process. The chosen measurement protocol will dictate the format of sequence numbers and time-stamps, if they are conveyed in the packet payload.
This section gives the details of the packet traffic which is the basis for measurement. In IPPM metrics, this is called the Stream, and can easily be described by providing the list of stream parameters.
Section 3 of [RFC3432] prescribes the method for generating Periodic streams using associated parameters.
NOTE: an initiation process with a number of control exchanges resulting in unpredictable start times (within a time interval) may be sufficient to avoid synchronization of periodic streams, and therefore a valid replacement for selecting a start time at random from a fixed interval.
The T0 parameter will be reported as a measured parameter. Parameters incT and dT are Fixed Parameters.
NA
NA
This category specifies all details of the Output of measurements using the metric.
Percentile -- for the conditional distribution of all packets with a valid value of one-way delay (undefined delays are excluded), a single value corresponding to the 95th percentile, as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
The percentile = 95, meaning that the reported delay, "95Percentile", is the smallest value of one-way PDV for which the Empirical Distribution Function (EDF), F(95Percentile) >= 95% of the singleton one-way PDV values in the conditional distribution. See section 11.3 of [RFC2330] for the definition of the percentile statistic using the EDF.
The 95th Percentile of one-way PDV is expressed in seconds.
Section 3.7.3 of [RFC7679] provides a means to quantify the systematic and random errors of a time measurement. In-situ calibration could be enabled with an internal loopback that includes as much of the measurement system as possible, performs address manipulation as needed, and provides some form of isolation (e.g., deterministic delay) to avoid send-receive interface contention. Some portion of the random and systematic error can be characterized this way.
For one-way delay measurements, the error calibration must include an assessment of the internal clock synchronization with its external reference (this internal clock is supplying timestamps for measurement). In practice, the time offsets [RFC5905] of clocks at both the source and destination are needed to estimate the systematic error due to imperfect clock synchronization (the time offsets are smoothed, thus the random variation is not usually represented in the results).
When a measurement controller requests a calibration measurement, the loopback is applied and the result is output in the same format as a normal measurement with additional indication that it is a calibration result. In any measurement, the measurement function SHOULD report its current estimate of time offset [RFC5905] as an indicator of the degree of synchronization.
Both internal loopback calibration and clock synchronization can be used to estimate the available accuracy of the Output Metric Units. For example, repeated loopback delay measurements will reveal the portion of the Output result resolution which is the result of system noise, and thus inaccurate.
Current
This RFC number
1.0
YYYY-MM-DD
Lost packets represent a challenge for delay variation metrics. See section 4.1 of [RFC3393] and the delay variation applicability statement[RFC5481] for extensive analysis and comparison of PDV and an alternate metric, IPDV.
This section gives initial registry entries for DNS Response Latency and Loss from a network user's perspective, for a specific named resource. The metric can be measured repeatedly using different names. RFC 2681 defines a Round-trip delay metric. We build on that metric by specifying several of the input parameters to precisely define two metrics for measuring DNS latency and loss.
Note to IANA: Each Registry "Name" below specifies a single registry entry, whose output format varies in accordance with the name.
All column entries beside the ID, Name, Description, and Output Reference Method categories are the same, thus this section proposes two closely-related registry entries. As a result, IANA is also asked to assign corresponding URLs to each Named Metric.
This category includes multiple indexes to the registry entries, the element ID and metric name.
<insert numeric identifier, an integer>
IANA is asked to assign different numeric identifiers to each of the two Named Metrics.
RTDNS_Active_IP-UDP-Poisson_RFCXXXXsec6_Seconds_Raw
RLDNS_Active_IP-UDP-Poisson_RFCXXXXsec6_Logical_Raw
URL: https://www.iana.org/ ... <name>
This is a metric for DNS Response performance from a network user's perspective, for a specific named resource. The metric can be measured repeatedly using different resource names.
RTDNS: This metric assesses the response time, the interval from the query transmission to the response.
RLDNS: This metric indicates that the response was deemed lost. In other words, the response time exceeded the maximum waiting time.
IETF
1.0
This category includes columns to prompt the entry of all necessary details related to the metric definition, including the RFC reference and values of input factors, called fixed parameters.
Mockapetris, P., "Domain names - implementation and specification", STD 13, RFC 1035, November 1987. (and updates)
Almes, G., Kalidindi, S., and M. Zekauskas, "A Round-trip Delay Metric for IPPM", RFC 2681, September 1999.
Section 2.4 of [RFC2681] provides the reference definition of the singleton (single value) Round-trip delay metric. Section 3.4 of [RFC2681] provides the reference definition expanded to cover a multi-singleton sample. Note that terms such as singleton and sample are defined in Section 11 of [RFC2330].
For DNS Response Latency, the entities in [RFC1035] must be mapped to [RFC2681]. The Local Host with its User Program and Resolver take the role of "Src", and the Foreign Name Server takes the role of "Dst".
Note that although the [RFC2681] definition of "Round-trip-Delay between Src and Dst at T" is directionally ambiguous in the text, this metric tightens the definition further to recognize that the host in the "Src" role will send the first packet to "Dst", and ultimately receive the corresponding return packet from "Dst" (when neither are lost).
Morton, A., "Round-trip Packet Loss Metrics", RFC 6673, August 2012.
Both response time and loss metrics employ a maximum waiting time for received responses, so the count of lost packets to total packets sent is the basis for the loss determination as per Section 4.3 of [RFC6673].
Type-P as defined in Section 13 of [RFC2330]:
Other measurement parameters:
Observation: reply packets will contain a DNS response and may contain RRs.
This category includes columns for references to relevant sections of the RFC(s) and any supplemental information needed to ensure an unambiguous methods for implementations.
The methodology for this metric is defined as Type-P-Round-trip-Delay-Poisson-Stream in section 2.6 of RFC 2681 and section 3.6 of RFC 2681 using the Type-P and Timeout defined under Fixed Parameters.
The reference method distinguishes between long-delayed packets and lost packets by implementing a maximum waiting time for packet arrival. Tmax is the waiting time used as the threshold to declare a response packet lost. Lost packets SHALL be designated as having undefined delay and counted for the RLDNS metric.
The calculations on the delay (RTT) SHALL be performed on the conditional distribution, conditioned on successful packet arrival within Tmax. Also, when all packet delays are stored, the process which calculates the RTT value MUST enforce the Tmax threshold on stored values before calculations. See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
The reference method requires some way to distinguish between different packets in a stream to establish correspondence between sending times and receiving times for each successfully-arriving reply.
DNS Messages bearing Queries provide for random ID Numbers in the Identification header field, so more than one query may be launched while a previous request is outstanding when the ID Number is used. Therefore, the ID Number MUST be retained at the Src and included with each response packet to disambiguate packet reordering if it occurs.
IF a DNS response does not arrive within Tmax, the response time RTDNS is undefined, and RLDNS = 1. The Message ID SHALL be used to disambiguate the successive queries that are otherwise identical.
Since the ID Number field is only 16 bits in length, it places a limit on the number of simultaneous outstanding DNS queries during a stress test from a single Src address.
Refer to Section 4.4 of [RFC6673] for expanded discussion of the instruction to "send a Type-P packet back to the Src as quickly as possible" in Section 2.6 of RFC 2681. However, the DNS Server is expected to perform all required functions to prepare and send a response, so the response time will include processing time and network delay. Section 8 of [RFC6673] presents additional requirements which SHALL be included in the method of measurement for this metric.
In addition to operations described in [RFC2681], the Src MUST parse the DNS headers of the reply and prepare the query response information for subsequent reporting as a measured result, along with the Round-Trip Delay.
This section gives the details of the packet traffic which is the basis for measurement. In IPPM metrics, this is called the Stream, and can easily be described by providing the list of stream parameters.
Section 11.1.3 of RFC 2681 provides three methods to generate Poisson sampling intervals. The reciprocal of lambda is the average packet spacing, thus the Run-time Parameter is Reciprocal_lambda = 1/lambda, in seconds.
Method 3 is used, where given a start time (Run-time Parameter), the subsequent send times are all computed prior to measurement by computing the pseudo-random distribution of inter-packet send times, (truncating the distribution as specified in the Run-time Parameters), and the Src sends each packet at the computed times.
Note that Trunc is the upper limit on inter-packet times in the Poisson distribution. A random value greater than Trunc is set equal to Trunc instead.
NA
NA
Run-time Parameters are input factors that must be determined, configured into the measurement system, and reported with the results for the context to be complete.
This category specifies all details of the Output of measurements using the metric.
Raw -- for each DNS Query packet sent, sets of values as defined in the next column, including the status of the response, only assigning delay values to successful query-response pairs.
For all outputs:
RTDNS: Round-trip Delay, dT, is expressed in seconds.
RTLDNS: the Logical value, where 1 = Lost and 0 = Received.
Section 3.7.3 of [RFC7679] provides a means to quantify the systematic and random errors of a time measurement. In-situ calibration could be enabled with an internal loopback at the Source host that includes as much of the measurement system as possible, performs address and payload manipulation as needed, and provides some form of isolation (e.g., deterministic delay) to avoid send-receive interface contention. Some portion of the random and systematic error can be characterized this way.
When a measurement controller requests a calibration measurement, the loopback is applied and the result is output in the same format as a normal measurement with additional indication that it is a calibration result.
Both internal loopback calibration and clock synchronization can be used to estimate the available accuracy of the Output Metric Units. For example, repeated loopback delay measurements will reveal the portion of the Output result resolution which is the result of system noise, and thus inaccurate.
Current
This RFC number
1.0
YYYY-MM-DD
None
This section specifies five initial registry entries for the UDP Poisson One-way Delay, and one for UDP Poisson One-way Loss.
IANA Note: Registry "Name" below specifies multiple registry entries, whose output format varies according to the <statistic> element of the name that specifies one form of statistical summary. There is an additional metric name for the Loss metric.
All column entries beside the ID, Name, Description, and Output Reference Method categories are the same, thus this section proposes six closely-related registry entries. As a result, IANA is also asked to assign corresponding URLs to each Named Metric.
This category includes multiple indexes to the registry entries, the element ID and metric name.
IANA is asked to assign different numeric identifiers to each of the six Metrics.
OWDelay_Active_IP-UDP-Poisson-Payload250B_RFCXXXXsec7_Seconds_<statistic>
where <statistic> is one of:
OWLoss_Active_IP-UDP-Poisson-Payload250B_RFCXXXXsec7_Percent_LossRatio
URL: https://www.iana.org/ ... <name>
OWDelay: This metric assesses the delay of a stream of packets exchanged between two hosts (or measurement points), and reports the <statistic> One-way delay for all successfully exchanged packets based on their conditional delay distribution.
where <statistic> is one of:
OWLoss: This metric assesses the loss ratio of a stream of packets exchanged between two hosts (which are the two measurement points), and the Output is the One-way loss ratio for all successfully received packets expressed as a percentage.
This category includes columns to prompt the entry of all necessary details related to the metric definition, including the RFC reference and values of input factors, called fixed parameters.
For Delay:
Almes, G., Kalidindi, S., Zekauskas, M., and A. Morton, Ed., "A One-Way Delay Metric for IP Performance Metrics (IPPM)", STD 81, RFC 7679, DOI 10.17487/RFC7679, January 2016, <http://www.rfc-editor.org/info/rfc7679>.
Morton, A., and Stephan, E., "Spatial Composition of Metrics", RFC 6049, January 2011.
Section 3.4 of [RFC7679] provides the reference definition of the singleton (single value) One-way delay metric. Section 4.4 of [RFC7679] provides the reference definition expanded to cover a multi-value sample. Note that terms such as singleton and sample are defined in Section 11 of [RFC2330].
Only successful packet transfers with finite delay are included in the sample, as prescribed in section 4.1.2 of [RFC6049].
For loss:
Almes, G., Kalidini, S., Zekauskas, M., and A. Morton, Ed., "A One-Way Loss Metric for IP Performance Metrics (IPPM)", RFC 7680, DOI 10.17487/RFC7680, January 2016, <http://www.rfc-editor.org/info/rfc7680>.
Section 2.4 of [RFC7680] provides the reference definition of the singleton (single value) one-way loss metric. Section 3.4 of [RFC7680] provides the reference definition expanded to cover a multi-singleton sample. Note that terms such as singleton and sample are defined in Section 11 of [RFC2330].
Type-P:
Other measurement parameters:
See the Packet Stream generation category for two additional Fixed Parameters.
This category includes columns for references to relevant sections of the RFC(s) and any supplemental information needed to ensure an unambiguous methods for implementations.
The methodology for this metric is defined as Type-P-One-way-Delay-Poisson-Stream in section 3.6 of [RFC7679] and section 4.6 of [RFC7679] using the Type-P and Tmax defined under Fixed Parameters.
The reference method distinguishes between long-delayed packets and lost packets by implementing a maximum waiting time for packet arrival. Tmax is the waiting time used as the threshold to declare a packet lost. Lost packets SHALL be designated as having undefined delay, and counted for the OWLoss metric.
The calculations on the one-way delay SHALL be performed on the conditional distribution, conditioned on successful packet arrival within Tmax. Also, when all packet delays are stored, the process which calculates the one-way delay value MUST enforce the Tmax threshold on stored values before calculations. See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
The reference method requires some way to distinguish between different packets in a stream to establish correspondence between sending times and receiving times for each successfully-arriving packet.
Since a standard measurement protocol is employed [RFC5357], then the measurement process will determine the sequence numbers or timestamps applied to test packets after the Fixed and Runtime parameters are passed to that process. The measurement protocol dictates the format of sequence numbers and time-stamps conveyed in the TWAMP-Test packet payload.
This section gives the details of the packet traffic which is the basis for measurement. In IPPM metrics, this is called the Stream, and can easily be described by providing the list of stream parameters.
Section 11.1.3 of RFC 2681 provides three methods to generate Poisson sampling intervals. The reciprocal of lambda is the average packet spacing, thus the Run-time Parameter is Reciprocal_lambda = 1/lambda, in seconds.
Method 3 SHALL be used, where given a start time (Run-time Parameter), the subsequent send times are all computed prior to measurement by computing the pseudo-random distribution of inter-packet send times, (truncating the distribution as specified in the Parameter Trunc), and the Src sends each packet at the computed times.
Note that Trunc is the upper limit on inter-packet times in the Poisson distribution. A random value greater than Trunc is set equal to Trunc instead.
NA
NA
Run-time Parameters are input factors that must be determined, configured into the measurement system, and reported with the results for the context to be complete.
This category specifies all details of the Output of measurements using the metric.
See subsection titles below for Types.
For all output types ---
For LossRatio -- the count of lost packets to total packets sent is the basis for the loss ratio calculation as per Section 4.1 of [RFC7680].
For each <statistic>, one of the following sub-sections apply:
The 95th percentile SHALL be calculated using the conditional distribution of all packets with a finite value of One-way delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.3 of [RFC3393] for details on the percentile statistic (where Round-trip delay should be substituted for "ipdv").
The percentile = 95, meaning that the reported delay, "95Percentile", is the smallest value of one-way delay for which the Empirical Distribution Function (EDF), F(95Percentile) >= 95% of the singleton one-way delay values in the conditional distribution. See section 11.3 of [RFC2330] for the definition of the percentile statistic using the EDF.
The mean SHALL be calculated using the conditional distribution of all packets with a finite value of One-way delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.2.2 of [RFC6049] for details on calculating this statistic, and 4.2.3 of [RFC6049].
The minimum SHALL be calculated using the conditional distribution of all packets with a finite value of One-way delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.3.2 of [RFC6049] for details on calculating this statistic, and 4.3.3 of [RFC6049].
The maximum SHALL be calculated using the conditional distribution of all packets with a finite value of One-way delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.3.2 of [RFC6049] for a closely related method for calculating this statistic, and 4.3.3 of [RFC6049]. The formula is as follows:
Max = (FiniteDelay [j])
such that for some index, j, where 1 <= j <= N
FiniteDelay[j] >= FiniteDelay[n] for all n
The Std_Dev SHALL be calculated using the conditional distribution of all packets with a finite value of One-way delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
Define Population Std_Dev_Delay as follows:
(where all packets n = 1 through N have a value for Delay[n],
and MeanDelay calculated as in 7.4.2.2), and SQRT[] is the
Square Root function:
_ _
| N |
| --- |
| 1 \ 2 |
Std_Dev = SQRT | ------- > (Delay[n] - MeanDelay) |
| (N) / |
| --- |
| n = 1 |
|_ _|
See section 6.1.4 of [RFC6049] for a closely related method for calculating this statistic. The formula is the classic calculation for standard deviation of a population.
The <statistic> of One-way Delay is expressed in seconds.
The One-way Loss Ratio is expressed as a percentage of lost packets to total packets sent.
Section 3.7.3 of [RFC7679] provides a means to quantify the systematic and random errors of a time measurement. In-situ calibration could be enabled with an internal loopback that includes as much of the measurement system as possible, performs address manipulation as needed, and provides some form of isolation (e.g., deterministic delay) to avoid send-receive interface contention. Some portion of the random and systematic error can be characterized this way.
For one-way delay measurements, the error calibration must include an assessment of the internal clock synchronization with its external reference (this internal clock is supplying timestamps for measurement). In practice, the time offsets [RFC5905] of clocks at both the source and destination are needed to estimate the systematic error due to imperfect clock synchronization (the time offsets [RFC5905] are smoothed, thus the random variation is not usually represented in the results).
When a measurement controller requests a calibration measurement, the loopback is applied and the result is output in the same format as a normal measurement with additional indication that it is a calibration result. In any measurement, the measurement function SHOULD report its current estimate of time offset [RFC5905] as an indicator of the degree of synchronization.
Both internal loopback calibration and clock synchronization can be used to estimate the available accuracy of the Output Metric Units. For example, repeated loopback delay measurements will reveal the portion of the Output result resolution which is the result of system noise, and thus inaccurate.
Current
This RFC number
1.0
YYYY-MM-DD
None
This section specifies five initial registry entries for the UDP Periodic One-way Delay, and one for UDP Periodic One-way Loss.
IANA Note: Registry "Name" below specifies multiple registry entries, whose output format varies according to the <statistic> element of the name that specifies one form of statistical summary. There is an additional metric name for the Loss metric.
All column entries beside the ID, Name, Description, and Output Reference Method categories are the same, thus this section proposes six closely-related registry entries. As a result, IANA is also asked to assign corresponding URLs to each Named Metric.
This category includes multiple indexes to the registry entries, the element ID and metric name.
IANA is asked to assign a different numeric identifiers to each of the six Metrics.
OWDelay_Active_IP-UDP-Periodic20m-Payload142B_RFCXXXXsec8_Seconds_<statistic>
where <statistic> is one of:
OWLoss_Active_IP-UDP-Periodic-Payload142B_RFCXXXXsec8_Percent_LossRatio
URL: https://www.iana.org/ ... <name>
OWDelay: This metric assesses the delay of a stream of packets exchanged between two hosts (or measurement points), and reports the <statistic> One-way delay for all successfully exchanged packets based on their conditional delay distribution.
where <statistic> is one of:
OWLoss: This metric assesses the loss ratio of a stream of packets exchanged between two hosts (which are the two measurement points), and the Output is the One-way loss ratio for all successfully received packets expressed as a percentage.
This category includes columns to prompt the entry of all necessary details related to the metric definition, including the RFC reference and values of input factors, called fixed parameters.
For Delay:
Almes, G., Kalidindi, S., Zekauskas, M., and A. Morton, Ed., "A One-Way Delay Metric for IP Performance Metrics (IPPM)", STD 81, RFC 7679, DOI 10.17487/RFC7679, January 2016, <http://www.rfc-editor.org/info/rfc7679>.
Morton, A., and Stephan, E., "Spatial Composition of Metrics", RFC 6049, January 2011.
Section 3.4 of [RFC7679] provides the reference definition of the singleton (single value) One-way delay metric. Section 4.4 of [RFC7679] provides the reference definition expanded to cover a multi-value sample. Note that terms such as singleton and sample are defined in Section 11 of [RFC2330].
Only successful packet transfers with finite delay are included in the sample, as prescribed in section 4.1.2 of [RFC6049].
For loss:
Almes, G., Kalidini, S., Zekauskas, M., and A. Morton, Ed., "A One-Way Loss Metric for IP Performance Metrics (IPPM)", RFC 7680, DOI 10.17487/RFC7680, January 2016, <http://www.rfc-editor.org/info/rfc7680>.
Section 2.4 of [RFC7680] provides the reference definition of the singleton (single value) one-way loss metric. Section 3.4 of [RFC7680] provides the reference definition expanded to cover a multi-singleton sample. Note that terms such as singleton and sample are defined in Section 11 of [RFC2330].
Type-P:
Other measurement parameters:
See the Packet Stream generation category for two additional Fixed Parameters.
This category includes columns for references to relevant sections of the RFC(s) and any supplemental information needed to ensure an unambiguous methods for implementations.
The methodology for this metric is defined as Type-P-One-way-Delay-Poisson-Stream in section 3.6 of [RFC7679] and section 4.6 of [RFC7679] using the Type-P and Tmax defined under Fixed Parameters. However, a Periodic stream is used, as defined in [RFC3432].
The reference method distinguishes between long-delayed packets and lost packets by implementing a maximum waiting time for packet arrival. Tmax is the waiting time used as the threshold to declare a packet lost. Lost packets SHALL be designated as having undefined delay, and counted for the OWLoss metric.
The calculations on the one-way delay SHALL be performed on the conditional distribution, conditioned on successful packet arrival within Tmax. Also, when all packet delays are stored, the process which calculates the one-way delay value MUST enforce the Tmax threshold on stored values before calculations. See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
The reference method requires some way to distinguish between different packets in a stream to establish correspondence between sending times and receiving times for each successfully-arriving packet.
Since a standard measurement protocol is employed [RFC5357], then the measurement process will determine the sequence numbers or timestamps applied to test packets after the Fixed and Runtime parameters are passed to that process. The measurement protocol dictates the format of sequence numbers and time-stamps conveyed in the TWAMP-Test packet payload.
This section gives the details of the packet traffic which is the basis for measurement. In IPPM metrics, this is called the Stream, and can easily be described by providing the list of stream parameters.
Section 3 of [RFC3432] prescribes the method for generating Periodic streams using associated parameters.
NOTE: an initiation process with a number of control exchanges resulting in unpredictable start times (within a time interval) may be sufficient to avoid synchronization of periodic streams, and therefore a valid replacement for selecting a start time at random from a fixed interval.
These stream parameters will be specified as Run-time parameters.
NA
NA
Run-time Parameters are input factors that must be determined, configured into the measurement system, and reported with the results for the context to be complete.
This category specifies all details of the Output of measurements using the metric.
See subsection titles in Reference Definition for Latency Types.
For all output types ---
For LossRatio -- the count of lost packets to total packets sent is the basis for the loss ratio calculation as per Section 4.1 of [RFC7680].
For each <statistic>, one of the following sub-sections apply:
The 95th percentile SHALL be calculated using the conditional distribution of all packets with a finite value of One-way delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.3 of [RFC3393] for details on the percentile statistic (where Round-trip delay should be substituted for "ipdv").
The percentile = 95, meaning that the reported delay, "95Percentile", is the smallest value of one-way delay for which the Empirical Distribution Function (EDF), F(95Percentile) >= 95% of the singleton one-way delay values in the conditional distribution. See section 11.3 of [RFC2330] for the definition of the percentile statistic using the EDF.
The mean SHALL be calculated using the conditional distribution of all packets with a finite value of One-way delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.2.2 of [RFC6049] for details on calculating this statistic, and 4.2.3 of [RFC6049].
The minimum SHALL be calculated using the conditional distribution of all packets with a finite value of One-way delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.3.2 of [RFC6049] for details on calculating this statistic, and 4.3.3 of [RFC6049].
The maximum SHALL be calculated using the conditional distribution of all packets with a finite value of One-way delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.3.2 of [RFC6049] for a closely related method for calculating this statistic, and 4.3.3 of [RFC6049]. The formula is as follows:
Max = (FiniteDelay [j])
such that for some index, j, where 1 <= j <= N
FiniteDelay[j] >= FiniteDelay[n] for all n
The Std_Dev SHALL be calculated using the conditional distribution of all packets with a finite value of One-way delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.3.2 of [RFC6049] for a closely related method for calculating this statistic, and 4.3.3 of [RFC6049]. The formula is the classic calculation for standard deviation of a population.
Define Population Std_Dev_Delay as follows:
(where all packets n = 1 through N have a value for Delay[n],
and MeanDelay calculated as in 7.4.2.2), and SQRT[] is the
Square Root function:
_ _
| N |
| --- |
| 1 \ 2 |
Std_Dev = SQRT | ------- > (Delay[n] - MeanDelay) |
| (N) / |
| --- |
| n = 1 |
|_ _|
The <statistic> of One-way Delay is expressed in seconds, where <statistic> is one of:
The One-way Loss Ratio is expressed as a percentage of lost packets to total packets sent.
Section 3.7.3 of [RFC7679] provides a means to quantify the systematic and random errors of a time measurement. In-situ calibration could be enabled with an internal loopback that includes as much of the measurement system as possible, performs address manipulation as needed, and provides some form of isolation (e.g., deterministic delay) to avoid send-receive interface contention. Some portion of the random and systematic error can be characterized this way.
For one-way delay measurements, the error calibration must include an assessment of the internal clock synchronization with its external reference (this internal clock is supplying timestamps for measurement). In practice, the time offsets [RFC5905] of clocks at both the source and destination are needed to estimate the systematic error due to imperfect clock synchronization (the time offsets [RFC5905] are smoothed, thus the random variation is not usually represented in the results).
When a measurement controller requests a calibration measurement, the loopback is applied and the result is output in the same format as a normal measurement with additional indication that it is a calibration result. In any measurement, the measurement function SHOULD report its current estimate of time offset [RFC5905] as an indicator of the degree of synchronization.
Both internal loopback calibration and clock synchronization can be used to estimate the available accuracy of the Output Metric Units. For example, repeated loopback delay measurements will reveal the portion of the Output result resolution which is the result of system noise, and thus inaccurate.
Current
This RFC number
1.0
YYYY-MM-DD
None.
This section specifies three initial registry entries for the ICMP Round-trip Latency, and another entry for ICMP Round-trip Loss Ratio.
IANA Note: Registry "Name" below specifies multiple registry entries, whose output format varies according to the <statistic> element of the name that specifies one form of statistical summary. There is an additional metric name for the Loss metric.
All column entries beside the ID, Name, Description, and Output Reference Method categories are the same, thus this section proposes two closely-related registry entries. As a result, IANA is also asked to assign corresponding URLs to each Named Metric.
This category includes multiple indexes to the registry entry: the element ID and metric name.
IANA is asked to assign different numeric identifiers to each of the four Named Metrics.
RTDelay_Active_IP-ICMP-SendOnRcv_RFCXXXXsec9_Seconds_<statistic>
where <statistic> is one of:
RTLoss_Active_IP-ICMP-SendOnRcv_RFCXXXXsec9_Percent_LossRatio
URL: https://www.iana.org/ ... <name>
RTDelay: This metric assesses the delay of a stream of ICMP packets exchanged between two hosts (which are the two measurement points), and the Output is the Round-trip delay for all successfully exchanged packets expressed as the <statistic> of their conditional delay distribution, where <statistic> is one of:
RTLoss: This metric assesses the loss ratio of a stream of ICMP packets exchanged between two hosts (which are the two measurement points), and the Output is the Round-trip loss ratio for all successfully exchanged packets expressed as a percentage.
IETF
1.0
This category includes columns to prompt the entry of all necessary details related to the metric definition, including the RFC reference and values of input factors, called fixed parameters.
Almes, G., Kalidindi, S., and M. Zekauskas, "A Round-trip Delay Metric for IPPM", RFC 2681, September 1999.
Section 2.4 of [RFC2681] provides the reference definition of the singleton (single value) Round-trip delay metric. Section 3.4 of [RFC2681] provides the reference definition expanded to cover a multi-singleton sample. Note that terms such as singleton and sample are defined in Section 11 of [RFC2330].
Note that although the [RFC2681] definition of "Round-trip-Delay between Src and Dst" is directionally ambiguous in the text, this metric tightens the definition further to recognize that the host in the "Src" role will send the first packet to "Dst", and ultimately receive the corresponding return packet from "Dst" (when neither are lost).
Finally, note that the variable "dT" is used in [RFC2681] to refer to the value of Round-trip delay in metric definitions and methods. The variable "dT" has been re-used in other IPPM literature to refer to different quantities, and cannot be used as a global variable name.
Morton, A., "Round-trip Packet Loss Metrics", RFC 6673, August 2012.
Both delay and loss metrics employ a maximum waiting time for received packets, so the count of lost packets to total packets sent is the basis for the loss ratio calculation as per Section 6.1 of [RFC6673].
Type-P as defined in Section 13 of [RFC2330]:
Other measurement parameters:
This category includes columns for references to relevant sections of the RFC(s) and any supplemental information needed to ensure an unambiguous methods for implementations.
The methodology for this metric is defined as Type-P-Round-trip-Delay-Poisson-Stream in section 2.6 of RFC 2681 and section 3.6 of RFC 2681 using the Type-P and Tmax defined under Fixed Parameters.
The reference method distinguishes between long-delayed packets and lost packets by implementing a maximum waiting time for packet arrival. Tmax is the waiting time used as the threshold to declare a packet lost. Lost packets SHALL be designated as having undefined delay, and counted for the RTLoss metric.
The calculations on the delay (RTD) SHALL be performed on the conditional distribution, conditioned on successful packet arrival within Tmax. Also, when all packet delays are stored, the process which calculates the RTD value MUST enforce the Tmax threshold on stored values before calculations. See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
The reference method requires some way to distinguish between different packets in a stream to establish correspondence between sending times and receiving times for each successfully-arriving packet. Sequence numbers or other send-order identification MUST be retained at the Src or included with each packet to disambiguate packet reordering if it occurs.
The measurement process will determine the sequence numbers applied to test packets after the Fixed and Runtime parameters are passed to that process. The ICMP measurement process and protocol will dictate the format of sequence numbers and other identifiers.
Refer to Section 4.4 of [RFC6673] for expanded discussion of the instruction to "send a Type-P packet back to the Src as quickly as possible" in Section 2.6 of RFC 2681. Section 8 of [RFC6673] presents additional requirements which MUST be included in the method of measurement for this metric.
This section gives the details of the packet traffic which is the basis for measurement. In IPPM metrics, this is called the Stream, and can easily be described by providing the list of stream parameters.
The ICMP metrics use a sending discipline called "SendOnRcv" or Send On Receive. This is a modification of Section 3 of [RFC3432], which prescribes the method for generating Periodic streams using associated parameters as defined below for this description:
The incT stream parameter will be specified as a Run-time parameter, and dT is not used in SendOnRcv.
A SendOnRcv sender behaves exactly like a Periodic stream generator while all reply packets arrive with RTD < incT, and the inter-packet interval will be constant.
If a reply packet arrives with RTD >= incT, then the inter-packet interval for the next sending time is nominally RTD.
If a reply packet fails to arrive within Tmax, then the inter-packet interval for the next sending time is nominally Tmax.
If an immediate send on reply arrival is desired, then set incT=0.
NA
NA
Run-time Parameters are input factors that must be determined, configured into the measurement system, and reported with the results for the context to be complete.
(see the Packet Stream Generation section for additional Run-time parameters)
This category specifies all details of the Output of measurements using the metric.
See subsection titles in Reference Definition for Latency Types.
LossRatio -- the count of lost packets to total packets sent is the basis for the loss ratio calculation as per Section 6.1 of [RFC6673].
For all output types ---
For LossRatio -- the count of lost packets to total packets sent is the basis for the loss ratio calculation as per Section 4.1 of [RFC7680].
For each <statistic>, one of the following sub-sections apply:
The mean SHALL be calculated using the conditional distribution of all packets with a finite value of Round-trip delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.2.2 of [RFC6049] for details on calculating this statistic, and 4.2.3 of [RFC6049].
The minimum SHALL be calculated using the conditional distribution of all packets with a finite value of Round-trip delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.3.2 of [RFC6049] for details on calculating this statistic, and 4.3.3 of [RFC6049].
The maximum SHALL be calculated using the conditional distribution of all packets with a finite value of Round-trip delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.3.2 of [RFC6049] for a closely related method for calculating this statistic, and 4.3.3 of [RFC6049]. The formula is as follows:
Max = (FiniteDelay [j])
such that for some index, j, where 1 <= j <= N
FiniteDelay[j] >= FiniteDelay[n] for all n
The <statistic> of Round-trip Delay is expressed in seconds, where <statistic> is one of:
The Round-trip Loss Ratio is expressed as a percentage of lost packets to total packets sent.
Section 3.7.3 of [RFC7679] provides a means to quantify the systematic and random errors of a time measurement. In-situ calibration could be enabled with an internal loopback at the Source host that includes as much of the measurement system as possible, performs address manipulation as needed, and provides some form of isolation (e.g., deterministic delay) to avoid send-receive interface contention. Some portion of the random and systematic error can be characterized this way.
When a measurement controller requests a calibration measurement, the loopback is applied and the result is output in the same format as a normal measurement with additional indication that it is a calibration result.
Both internal loopback calibration and clock synchronization can be used to estimate the available accuracy of the Output Metric Units. For example, repeated loopback delay measurements will reveal the portion of the Output result resolution which is the result of system noise, and thus inaccurate.
Current
This RFC number
1.0
YYYY-MM-DD
None
This section specifies three initial registry entries for the Passive assessment of TCP Round-Trip Delay (RTD) and another entry for TCP Round-trip Loss Count.
IANA Note: Registry "Name" below specifies multiple registry entries, whose output format varies according to the <statistic> element of the name that specifies one form of statistical summary. There are two additional metric names for Singleton RT Delay and Packet Count metrics.
All column entries beside the ID, Name, Description, and Output Reference Method categories are the same, thus this section proposes four closely-related registry entries. As a result, IANA is also asked to assign corresponding URLs to each Named Metric.
This category includes multiple indexes to the registry entry: the element ID and metric name.
IANA is asked to assign different numeric identifiers to each of the four Named Metrics.
RTDelay_Passive_IP-TCP_RFCXXXXsec10_Seconds_<statistic>
where <statistic> is one of:
RTDelay_Passive_IP-TCP-HS_RFCXXXXsec10_Seconds_Singleton
Note that a mid-point observer only has the opportunity to compose a single RTDelay on the TCP Hand Shake.
RTLoss_Passive_IP-TCP_RFCXXXXsec10_Packet_Count
URL: https://www.iana.org/ ... <name>
RTDelay: This metric assesses the round-trip delay of TCP packets constituting a single connection, exchanged between two hosts. We consider the measurement of round-trip delay based on a single Observation Point [RFC7011] somewhere in the network. The Output is the Round-trip delay for all successfully exchanged packets expressed as the <statistic> of their conditional delay distribution, where <statistic> is one of:
RTLoss: This metric assesses the estimated loss count for TCP packets constituting a single connection, exchanged between two hosts. We consider the measurement of round-trip delay based on a single Observation Point [RFC7011] somewhere in the network. The Output is the estimated Loss Count for the measurement interval.
IETF
1.0
This category includes columns to prompt the entry of all necessary details related to the metric definition, including the RFC reference and values of input factors, called fixed parameters.
Although there is no RFC that describes passive measurement of Round-Trip Delay, the parallel definition for Active measurement is:
Almes, G., Kalidindi, S., and M. Zekauskas, "A Round-trip Delay Metric for IPPM", RFC 2681, September 1999.
This metric definition uses the terms singleton and sample as defined in Section 11 of [RFC2330]. (Section 2.4 of [RFC2681] provides the reference definition of the singleton (single value) Round-trip delay metric. Section 3.4 of [RFC2681] provides the reference definition expanded to cover a multi-singleton sample.)
With the Observation Point [RFC7011] (OP) typically located between the hosts participating in the TCP connection, the Round-trip Delay metric requires two individual measurements between the OP and each host, such that the Spatial Composition [RFC6049]of the measurements yields a Round-trip Delay singleton (we are extending the composition of one-way subpath delays to subpath round-trip delay).
Using the direction of TCP SYN transmission to anchor the nomenclature, host A sends the SYN and host B replies with SYN-ACK during connection establishment. The direction of SYN transfer is considered the Forward direction of transmission, from A through OP to B (Reverse is B through OP to A).
Traffic filters reduce the packet stream at the OP to a Qualified bidirectional flow of packets.
In the definitions below, Corresponding Packets are transferred in different directions and convey a common value in a TCP header field that establishes correspondence (to the extent possible). Examples may be found in the TCP timestamp fields.
For a real number, RTD_fwd, >> the Round-trip Delay in the Forward direction from OP to host B at time T' is RTD_fwd << it is REQUIRED that OP observed a Qualified Packet to host B at wire-time T', that host B received that packet and sent a Corresponding Packet back to host A, and OP observed the Corresponding Packet at wire-time T' + RTD_fwd.
For a real number, RTD_rev, >> the Round-trip Delay in the Reverse direction from OP to host A at time T'' is RTD_rev << it is REQUIRED that OP observed a Qualified Packet to host A at wire-time T'', that host A received that packet and sent a Corresponding Packet back to host B, and that OP observed the Corresponding Packet at wire-time T'' + RTD_rev.
Ideally, the packet sent from host B to host A in both definitions above SHOULD be the same packet (or, when measuring RTD_rev first, the packet from host A to host B in both definitions should be the same).
The REQUIRED Composition Function for a singleton of Round-trip Delay at time T (where T is the earliest of T' and T'' above) is:
RTDelay = RTD_fwd + RTD_rev
Note that when OP is located at host A or host B, one of the terms composing RTDelay will be zero or negligible.
When the Qualified and Corresponding Packets are a TCP-SYN and a TCP-SYN-ACK, then RTD_fwd == RTD_HS_fwd.
When the Qualified and Corresponding Packets are a TCP-SYN-ACK and a TCP-ACK, then RTD_rev == RTD_HS_rev.
The REQUIRED Composition Function for a singleton of Round-trip Delay for the connection Hand Shake:
RTDelay_HS = RTD_HS_fwd + RTD_HS_rev
The definition of Round-trip Loss Count uses the nomenclature developed above, based on observation of the TCP header sequence numbers and storing the sequence number gaps observed. Packet Losses can be inferred from:
Each observation of an out-of-order or duplicate infers a singleton of loss, but composition of Round-trip Loss Counts will be conducted over a measurement interval which is synonymous with a single TCP connection.
With the above observations in the Forward direction over a measurement interval, the count of out-of-order and duplicate segments is defined as RTL_fwd. Comparable observations in the Reverse direction are defined as RTL_rev.
For a measurement interval (corresponding to a single TCP connection), T0 to Tf, the REQUIRED Composition Function for a the two single-direction counts of inferred loss is:
RTLoss = RTL_fwd + RTL_rev
Traffic Filters:
This category includes columns for references to relevant sections of the RFC(s) and any supplemental information needed to ensure an unambiguous methods for implementations.
The foundation methodology for this metric is defined in Section 4 of [RFC7323] using the Timestamp Option with modifications that allow application at a mid-path Observation Point (OP) [RFC7011]. Further details and applicable heuristics were derived from [Strowes] and [Trammell-14].
The Traffic Filter at the OP is configured to observe a single TCP connection. When the SYN, SYN-ACK, ACK handshake occurs, it offers the first opportunity to measure both RTD_fwd (on the SYN to SYN-ACK pair) and RTD_rev (on the SYN-ACK to ACK pair). Label this singleton of RTDelay as RTDelay_HS (composed using the forward and reverse measurement pair). RTDelay_HS SHALL be treated separately from other RTDelays on data-bearing packets and their ACKs. The RTDelay_HS value MAY be used as a sanity check on other Composed values of RTDelay.
For payload bearing packets, the OP measures the time interval between observation of a packet with Sequence Number s, and the corresponding ACK with same Sequence number. When the payload is transferred from host A to host B, the observed interval is RTD_fwd.
Because many data transfers are unidirectional (say, in the Forward direction from host A to host B), it is necessary to use pure ACK packets with Timestamp (TSval) and their Timestamp value echo to perform a RTD_rev measurement. The time interval between observation of the ACK from B to A, and the corresponding packet with Timestamp echo (TSecr) is the RTD_rev.
Delay Measurement Filtering Heuristics:
If Data payloads were transferred in both Forward and Reverse directions, then the Round-Trip Time Measurement Rule in Section 4.1 of [RFC7323] could be applied. This rule essentially excludes any measurement using a packet unless it makes progress in the transfer (advances the left edge of the send window, consistent with [Strowes]).
A different heuristic from [Trammell-14] is to exclude any RTD_rev that is larger than previously observed values. This would tend to exclude Reverse measurements taken when the Application has no data ready to send, because considerable time could be added to RTD_rev from this source of error.
Note that the above Heuristic assumes that host A is sending data. Host A expecting a download would mean that this heuristic should be applied to RTD_fwd.
The statistic calculations to summarize the delay (RTDelay) SHALL be performed on the conditional distribution, conditioned on successful Forward and Reverse measurements which follow the Heuristics.
Method for Inferring Loss:
The OP tracks sequence numbers and stores gaps for each direction of transmission, as well as the next-expected sequence number as in [Trammell-14] and [RFC4737]. Loss is inferred from Out-of-order segments and Duplicate segments.
Loss Measurement Filtering Heuristics:
[Trammell-14] adds a window of evaluation based on the RTDelay.
Distinguish Re-ordered from OOO due to loss, because sequence number gap is filled during the same RTDelay window. Segments detected as re-ordered according to [RFC4737] MUST reduce the Loss Count inferred from Out-of-order segments.
Spurious (unneeded) retransmissions (observed as duplicates) can also be reduced this way, as described in [Trammell-14].
Sources of Error:
The principal source of RTDelay error is the host processing time to return a packet that defines the termination of a time interval. The heuristics above intend to mitigate these errors by excluding measurements where host processing time is a significant part of RTD_fwd or RTD_rev.
A key source of RTLoss error is observation loss, described in section 3 of [Trammell-14].
NA
The Fixed Parameters above give a portion of the Traffic Filter. Other aspects will be supplied as Run-time Parameters (below).
This metric requires a complete sample of all packets that qualify according to the Traffic Filter criteria.
Run-time Parameters are input factors that must be determined, configured into the measurement system, and reported with the results for the context to be complete.
This category specifies all details of the Output of measurements using the metric.
See subsection titles in Reference Definition for RTDelay Types.
For RTLoss -- the count of lost packets.
For all output types ---
For RTDelay_HS -- the Round trip delay of the Handshake.
For RTLoss -- the count of lost packets.
For each <statistic>, one of the following sub-sections apply:
The mean SHALL be calculated using the conditional distribution of all packets with a finite value of Round-trip delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.2.2 of [RFC6049] for details on calculating this statistic, and 4.2.3 of [RFC6049].
The minimum SHALL be calculated using the conditional distribution of all packets with a finite value of Round-trip delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.3.2 of [RFC6049] for details on calculating this statistic, and 4.3.3 of [RFC6049].
The maximum SHALL be calculated using the conditional distribution of all packets with a finite value of Round-trip delay (undefined delays are excluded), a single value as follows:
See section 4.1 of [RFC3393] for details on the conditional distribution to exclude undefined values of delay, and Section 5 of [RFC6703] for background on this analysis choice.
See section 4.3.2 of [RFC6049] for a closely related method for calculating this statistic, and 4.3.3 of [RFC6049]. The formula is as follows:
Max = (FiniteDelay [j])
such that for some index, j, where 1 <= j <= N
FiniteDelay[j] >= FiniteDelay[n] for all n
The <statistic> of Round-trip Delay is expressed in seconds, where <statistic> is one of:
The Round-trip Delay of the Hand Shake is expressed in seconds.
The Round-trip Loss Count is expressed as a number of packets.
Passive measurements at an OP could be calibrated against an active measurement (with loss emulation) at host A or B, where the active measurement represents the ground-truth.
Current
This RFC number
1.0
YYYY-MM-DD
None.
These registry entries represent no known implications for Internet Security. Each RFC referenced above contains a Security Considerations section. Further, the LMAP Framework [RFC7594] provides both security and privacy considerations for measurements.
There are potential privacy considerations for observed traffic, particularly for passive metrics in section 10. An attacker that knows that its TCP connection is being measured can modify its behavior to skew the measurement results.
IANA is requested to populate The Performance Metrics Registry defined in [I-D.ietf-ippm-metric-registry] with the values defined in sections 4 through 10.
See the IANA Considerations section of [I-D.ietf-ippm-metric-registry] for additional requests and considerations.
The authors thank Brian Trammell for suggesting the term "Run-time Parameters", which led to the distinction between run-time and fixed parameters implemented in this memo, for identifying the IPFIX metric with Flow Key as an example, for suggesting the Passive TCP RTD metric and supporting references, and for many other productive suggestions. Thanks to Peter Koch, who provided several useful suggestions for disambiguating successive DNS Queries in the DNS Response time metric.
The authors also acknowledge the constructive reviews and helpful suggestions from Barbara Stark, Juergen Schoenwaelder, Tim Carey, Yaakov Stein, and participants in the LMAP working group. Thanks to Michelle Cotton for her early IANA reviews, and to Amanda Barber for answering questions related to the presentation of the registry and accessibility of the complete template via URL.
| [RFC1242] | Bradner, S., "Benchmarking Terminology for Network Interconnection Devices", RFC 1242, DOI 10.17487/RFC1242, July 1991. |
| [RFC6390] | Clark, A. and B. Claise, "Guidelines for Considering New Performance Metric Development", BCP 170, RFC 6390, DOI 10.17487/RFC6390, October 2011. |
| [RFC6703] | Morton, A., Ramachandran, G. and G. Maguluri, "Reporting IP Network Performance Metrics: Different Points of View", RFC 6703, DOI 10.17487/RFC6703, August 2012. |
| [RFC7594] | Eardley, P., Morton, A., Bagnulo, M., Burbridge, T., Aitken, P. and A. Akhter, "A Framework for Large-Scale Measurement of Broadband Performance (LMAP)", RFC 7594, DOI 10.17487/RFC7594, September 2015. |