| Network Working Group | D. Kumar |
| Internet-Draft | Cisco |
| Intended status: Standards Track | M. Wang |
| Expires: March 4, 2018 | Q. Wu |
| Huawei | |
| R. Rahman | |
| S. Raghavan | |
| Cisco | |
| August 31, 2017 |
Retrieval Methods YANG Data Model for Connectionless Operations, Administration, and Maintenance(OAM) protocols
draft-ietf-lime-yang-connectionless-oam-methods-06
This document presents a retrieval method YANG Data model for connectionless OAM protocols. It provides technology-independent RPC operations for connectionless OAM protocols. The retrieval methods model presented here can be extended to include technology specific details. This is leading to uniformity between OAM protocols and support both nested OAM workflows (i.e., performing OAM functions at different levels through a unified interface) and interacting OAM workflows ( i.e., performing OAM functions at same levels through a unified interface).
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."
This Internet-Draft will expire on March 4, 2018.
Copyright (c) 2017 IETF Trust and the persons identified as the document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.
Operations, Administration, and Maintenance (OAM) are important networking functions that allow operators to:
An overview of OAM tools is presented at [RFC7276].
Ping and Traceroute [RFC792], [RFC4443] and BFD [RFC5880] are well-known fault verification and isolation tools, respectively, for IP networks. Over the years, different technologies have developed similar tools for similar purposes.
In this document, we present a retrieval method YANG Data model for connectionless OAM protocols. This module provides technology-independent RPC operations for connectionless OAM protocols. It is separated from the generic YANG model for connectionless OAM [I-D.ietf-lime-yang-connectionless-oam] and can avoid mixing the models for the retrieved-data from the retrieval procedures. It is expected that retrieval procedures would evolve faster than the data model [I-D.ietf-lime-yang-connectionless-oam] and will allow new procedures to be defined for retrieval of the same data defined by the base data model.
The following terms are defined in [RFC6241] and are not redefined here:
The following terms are defined in [RFC6020] and are not redefined here: [RFC6020].
The terminology for describing YANG data models is found in
TP - Test Point
MAC - Media Access Control
RPC - A Remote Procedure Call
RPC operation - A specific Remote Procedure Call
A simplified graphical representation of the data model is used in this document. The meaning of the symbols in these diagrams is as follows:
<status> <flags> <name> <opts> <type>
<status> is one of:
+ for current
<flags> is one of:
rw for configuration data
ro for non-configuration data
-x for rpcs
-n for notifications
<name> is the name of the node
Each node is printed as:
<opts> is one of:
? for an optional leaf or choice
! for a presence container
* for a leaf-list or list
[<keys>] for a list's keys
<type> is the name of the type for leafs and leaf-lists
If the node is augmented into the tree from another module, its name is printed as <prefix>:<name>.
In this document, we present a retrieval method YANG Data model for connectionless OAM protocols. This module provides technology-independent retrieval procedures (RPC operations) for connectionless OAM protocols. It provides a flexible way to retrieve the data which defined by the "ietf-connectionless-oam.yang" [I-D.ietf-lime-yang-connectionless-oam].
The RPC model facilitates issuing commands to a NETCONF server (in this case to the device that need to execute the OAM command) and obtaining a response.
Under 'connectionless-oam-methods' module, we summarize common OAM functions and define two generic RPC operations: 'continuity-check' and 'path-discovery'. In practice, these RPC operations are supported by corresponding technology-specific OAM tools [RFC7276]. For example, for the IP OAM model, the continuity-check RPC corresponds to the IP Ping [RFC792] [RFC4443], while the path-discovery RPC operation corresponds to IP Traceroute [RFC792] [RFC4443].
Note that the RPC operation presented in this document is the base building block, which is used to derive a model for a technology-specific OAM (i.e., ICMP ping [RFC792] [RFC4443], LSP ping [RFC8029]), the base building block should be extended with corresponding technology specific parameters. To facilitate this for future enhancements to data retrieval methods, the RPCs are captured under a separate module.
The generic 'path-discovery-data' and 'continuity-check-data' groupings are used as data outputs from different RPCs described in this document. Similar methods including other RPCs can retrieve the data using the same data model.
rpc continuity-check {
if-feature coam:continuity-check;
description
"Generates continuity-check as per RFC7276.";
input {
container destination-tp {
uses coam:tp-address;
description
"destination test point.";
}
uses coam:session-type;
leaf source-interface {
type if:interface-ref;
description
"source interface.";
}
leaf outbound-interface {
type if:interface-ref;
description
"outbound interface.";
}
leaf count {
type empty;
description
"Specifies the number of packets that will be sent.";
}
leaf vrf {
type coam:routing-instance-ref;
description
"vrf instance.";
}
leaf ttl {
type uint8;
default "255";
description
"Time to live (TTL).";
}
leaf packet-size {
type uint32 {
range "64..10000";
}
default "64";
description
"Size of ping echo request packets, in octets";
}
}
output {
list error-code-list {
key "response-index";
leaf response-index {
type uint32;
description
"response index.";
}
leaf status-code {
type int32;
description
"error code is ";
}
leaf status-sub-code {
type uint8;
description
"sub code.";
}
description
"error code list.";
}
uses coam:continuity-check-data;
}
}
rpc path-discovery {
description
"Generates path discovery as per RFC7276.";
input {
container destination-tp {
uses coam:tp-address;
description
"destination test point.";
}
uses coam:session-type;
leaf source-interface {
type if:interface-ref;
description
"source interface.";
}
leaf outbound-interface {
type if:interface-ref;
description
"outbound interface.";
}
leaf vrf {
type coam:routing-instance-ref;
description
"vrf";
}
leaf max-ttl {
type uint8;
default "255";
description
"max ttl.";
}
}
output {
list response-list {
key "response-index";
description
"path discovery response list.";
leaf response-index {
type uint32;
description
"response index.";
}
leaf status-code {
type int32;
description
"error code is ";
}
leaf status-sub-code {
type uint8;
description
"sub code is ";
}
}
uses coam:path-discovery-data;
}
}
Snippet of data hierarchy related to RPC operations
The complete data hierarchy related to the Connectionless OAM Retrieval Methods YANG model is presented below.
module: ietf-connectionless-oam-methods
rpcs:
+---x continuity-check {coam:continuity-check}?
| +---w input
| | +---w destination-tp
| | | +---w tp-location-type? identityref
| | | +---w tp-address
| | | +---w mac-address
| | | | +---w mac-address? yang:mac-address
| | | +---w ipv4-address
| | | | +---w ipv4-address? inet:ipv4-address
| | | +---w ipv6-address
| | | | +---w ipv6-address? inet:ipv6-address
| | | +---w tp-attribute
| | | | +---w tp-attribute-type? address-attribute-type
| | | | +---w (tp-attribute-value)?
| | | | +--:(ip-prefix)
| | | | | +---w ip-prefix? inet:ip-prefix
| | | | +--:(bgp)
| | | | | +---w bgp? inet:ip-prefix
| | | | +--:(tunnel)
| | | | | +---w tunnel-interface? uint32
| | | | +--:(pw)
| | | | | +---w remote-pe-address? inet:ip-address
| | | | | +---w pw-id? uint32
| | | | +--:(vpls)
| | | | | +---w route-distinguisher? uint64
| | | | | +---w sender-ve-id? uint16
| | | | | +---w receiver-ve-id? uint16
| | | | +--:(mpls-mldp)
| | | | +---w (root-address)?
| | | | +--:(ip-address)
| | | | | +---w source-address? inet:ip-address
| | | | | +---w group-ip-address? inet:ip-address
| | | | +--:(vpn)
| | | | | +---w as-number? inet:as-number
| | | | +--:(global-id)
| | | | +---w lsp-id? string
| | | +---w system-info
| | | +---w system-id? router-id
| | +---w session-type? enumeration
| | +---w source-interface? if:interface-ref
| | +---w outbound-interface? if:interface-ref
| | +---w count? empty
| | +---w vrf? coam:routing-instance-ref
| | +---w ttl? uint8
| | +---w packet-size? uint32
| +--ro output
| +--ro error-code-list* [response-index]
| | +--ro response-index uint32
| | +--ro status-code? int32
| | +--ro status-sub-code? uint8
| +--ro src-test-point
| | +--ro ni? routing-instance-ref
| | +--ro tp-location-type? identityref
| | +--ro tp-address
| | | +--ro mac-address
| | | | +--ro mac-address? yang:mac-address
| | | +--ro ipv4-address
| | | | +--ro ipv4-address? inet:ipv4-address
| | | +--ro ipv6-address
| | | | +--ro ipv6-address? inet:ipv6-address
| | | +--ro tp-attribute
| | | | +--ro tp-attribute-type? address-attribute-type
| | | | +--ro (tp-attribute-value)?
| | | | +--:(ip-prefix)
| | | | | +--ro ip-prefix? inet:ip-prefix
| | | | +--:(bgp)
| | | | | +--ro bgp? inet:ip-prefix
| | | | +--:(tunnel)
| | | | | +--ro tunnel-interface? uint32
| | | | +--:(pw)
| | | | | +--ro remote-pe-address? inet:ip-address
| | | | | +--ro pw-id? uint32
| | | | +--:(vpls)
| | | | | +--ro route-distinguisher? uint64
| | | | | +--ro sender-ve-id? uint16
| | | | | +--ro receiver-ve-id? uint16
| | | | +--:(mpls-mldp)
| | | | +--ro (root-address)?
| | | | +--:(ip-address)
| | | | | +--ro source-address? inet:ip-address
| | | | | +--ro group-ip-address? inet:ip-address
| | | | +--:(vpn)
| | | | | +--ro as-number? inet:as-number
| | | | +--:(global-id)
| | | | +--ro lsp-id? string
| | | +--ro system-info
| | | +--ro system-id? router-id
| | +--ro egress-intf-name? if:interface-ref
| +--ro dest-test-point
| | +--ro ni? routing-instance-ref
| | +--ro tp-location-type? identityref
| | +--ro tp-address
| | | +--ro mac-address
| | | | +--ro mac-address? yang:mac-address
| | | +--ro ipv4-address
| | | | +--ro ipv4-address? inet:ipv4-address
| | | +--ro ipv6-address
| | | | +--ro ipv6-address? inet:ipv6-address
| | | +--ro tp-attribute
| | | | +--ro tp-attribute-type? address-attribute-type
| | | | +--ro (tp-attribute-value)?
| | | | +--:(ip-prefix)
| | | | | +--ro ip-prefix? inet:ip-prefix
| | | | +--:(bgp)
| | | | | +--ro bgp? inet:ip-prefix
| | | | +--:(tunnel)
| | | | | +--ro tunnel-interface? uint32
| | | | +--:(pw)
| | | | | +--ro remote-pe-address? inet:ip-address
| | | | | +--ro pw-id? uint32
| | | | +--:(vpls)
| | | | | +--ro route-distinguisher? uint64
| | | | | +--ro sender-ve-id? uint16
| | | | | +--ro receiver-ve-id? uint16
| | | | +--:(mpls-mldp)
| | | | +--ro (root-address)?
| | | | +--:(ip-address)
| | | | | +--ro source-address? inet:ip-address
| | | | | +--ro group-ip-address? inet:ip-address
| | | | +--:(vpn)
| | | | | +--ro as-number? inet:as-number
| | | | +--:(global-id)
| | | | +--ro lsp-id? string
| | | +--ro system-info
| | | +--ro system-id? router-id
| | +--ro ingress-intf-name? if:interface-ref
| +--ro sequence-number? uint64
| +--ro hop-cnt? uint8
| +--ro session-packet-statistics
| | +--ro rx-packet-count? uint32
| | +--ro tx-packet-count? uint32
| | +--ro rx-bad-packet? uint32
| | +--ro tx-packet-failed? uint32
| +--ro session-error-statistics
| | +--ro packet-drops-count? uint32
| | +--ro packet-reorder-count? uint32
| | +--ro packets-out-of-seq-count? uint32
| | +--ro packets-dup-count? uint32
| +--ro session-delay-statistics
| | +--ro time-resolution-value? identityref
| | +--ro min-delay-value? uint32
| | +--ro max-delay-value? uint32
| | +--ro average-delay-value? uint32
| +--ro session-jitter-statistics
| +--ro time-resolution-value? identityref
| +--ro min-jitter-value? uint32
| +--ro max-jitter-value? uint32
| +--ro average-jitter-value? uint32
+---x path-discovery {coam:path-discovery}?
+---w input
| +---w destination-tp
| | +---w tp-location-type? identityref
| | +---w tp-address
| | +---w mac-address
| | | +---w mac-address? yang:mac-address
| | +---w ipv4-address
| | | +---w ipv4-address? inet:ipv4-address
| | +---w ipv6-address
| | | +---w ipv6-address? inet:ipv6-address
| | +---w tp-attribute
| | | +---w tp-attribute-type? address-attribute-type
| | | +---w (tp-attribute-value)?
| | | +--:(ip-prefix)
| | | | +---w ip-prefix? inet:ip-prefix
| | | +--:(bgp)
| | | | +---w bgp? inet:ip-prefix
| | | +--:(tunnel)
| | | | +---w tunnel-interface? uint32
| | | +--:(pw)
| | | | +---w remote-pe-address? inet:ip-address
| | | | +---w pw-id? uint32
| | | +--:(vpls)
| | | | +---w route-distinguisher? uint64
| | | | +---w sender-ve-id? uint16
| | | | +---w receiver-ve-id? uint16
| | | +--:(mpls-mldp)
| | | +---w (root-address)?
| | | +--:(ip-address)
| | | | +---w source-address? inet:ip-address
| | | | +---w group-ip-address? inet:ip-address
| | | +--:(vpn)
| | | | +---w as-number? inet:as-number
| | | +--:(global-id)
| | | +---w lsp-id? string
| | +---w system-info
| | +---w system-id? router-id
| +---w session-type? enumeration
| +---w source-interface? if:interface-ref
| +---w outbound-interface? if:interface-ref
| +---w vrf? coam:routing-instance-ref
| +---w max-ttl? uint8
+--ro output
+--ro response-list* [response-index]
| +--ro response-index uint32
| +--ro status-code? int32
| +--ro status-sub-code? uint8
+--ro src-test-point
| +--ro ni? routing-instance-ref
| +--ro tp-location-type? identityref
| +--ro tp-address
| +--ro mac-address
| | +--ro mac-address? yang:mac-address
| +--ro ipv4-address
| | +--ro ipv4-address? inet:ipv4-address
| +--ro ipv6-address
| | +--ro ipv6-address? inet:ipv6-address
| +--ro tp-attribute
| | +--ro tp-attribute-type? address-attribute-type
| | +--ro (tp-attribute-value)?
| | +--:(ip-prefix)
| | | +--ro ip-prefix? inet:ip-prefix
| | +--:(bgp)
| | | +--ro bgp? inet:ip-prefix
| | +--:(tunnel)
| | | +--ro tunnel-interface? uint32
| | +--:(pw)
| | | +--ro remote-pe-address? inet:ip-address
| | | +--ro pw-id? uint32
| | +--:(vpls)
| | | +--ro route-distinguisher? uint64
| | | +--ro sender-ve-id? uint16
| | | +--ro receiver-ve-id? uint16
| | +--:(mpls-mldp)
| | +--ro (root-address)?
| | +--:(ip-address)
| | | +--ro source-address? inet:ip-address
| | | +--ro group-ip-address? inet:ip-address
| | +--:(vpn)
| | | +--ro as-number? inet:as-number
| | +--:(global-id)
| | +--ro lsp-id? string
| +--ro system-info
| +--ro system-id? router-id
+--ro dest-test-point
| +--ro ni? routing-instance-ref
| +--ro tp-location-type? identityref
| +--ro tp-address
| +--ro mac-address
| | +--ro mac-address? yang:mac-address
| +--ro ipv4-address
| | +--ro ipv4-address? inet:ipv4-address
| +--ro ipv6-address
| | +--ro ipv6-address? inet:ipv6-address
| +--ro tp-attribute
| | +--ro tp-attribute-type? address-attribute-type
| | +--ro (tp-attribute-value)?
| | +--:(ip-prefix)
| | | +--ro ip-prefix? inet:ip-prefix
| | +--:(bgp)
| | | +--ro bgp? inet:ip-prefix
| | +--:(tunnel)
| | | +--ro tunnel-interface? uint32
| | +--:(pw)
| | | +--ro remote-pe-address? inet:ip-address
| | | +--ro pw-id? uint32
| | +--:(vpls)
| | | +--ro route-distinguisher? uint64
| | | +--ro sender-ve-id? uint16
| | | +--ro receiver-ve-id? uint16
| | +--:(mpls-mldp)
| | +--ro (root-address)?
| | +--:(ip-address)
| | | +--ro source-address? inet:ip-address
| | | +--ro group-ip-address? inet:ip-address
| | +--:(vpn)
| | | +--ro as-number? inet:as-number
| | +--:(global-id)
| | +--ro lsp-id? string
| +--ro system-info
| +--ro system-id? router-id
+--ro sequence-number? uint64
+--ro hop-cnt? uint8
+--ro session-packet-statistics
| +--ro rx-packet-count? uint32
| +--ro tx-packet-count? uint32
| +--ro rx-bad-packet? uint32
| +--ro tx-packet-failed? uint32
+--ro session-error-statistics
| +--ro packet-drops-count? uint32
| +--ro packet-reorder-count? uint32
| +--ro packets-out-of-seq-count? uint32
| +--ro packets-dup-count? uint32
+--ro session-delay-statistics
| +--ro time-resolution-value? identityref
| +--ro min-delay-value? uint32
| +--ro max-delay-value? uint32
| +--ro average-delay-value? uint32
+--ro session-jitter-statistics
| +--ro time-resolution-value? identityref
| +--ro min-jitter-value? uint32
| +--ro max-jitter-value? uint32
| +--ro average-jitter-value? uint32
+--ro path-verification
| +--ro flow-info? string
| +--ro session-path-verification-statistics
| +--ro verified-count? uint32
| +--ro failed-count? uint32
+--ro path-trace-info
+--ro path-trace-info-list* [index]
+--ro index uint32
+--ro ni? routing-instance-ref
+--ro tp-location-type? identityref
+--ro tp-address
| +--ro mac-address
| | +--ro mac-address? yang:mac-address
| +--ro ipv4-address
| | +--ro ipv4-address? inet:ipv4-address
| +--ro ipv6-address
| | +--ro ipv6-address? inet:ipv6-address
| +--ro tp-attribute
| | +--ro tp-attribute-type? address-attribute-type
| | +--ro (tp-attribute-value)?
| | +--:(ip-prefix)
| | | +--ro ip-prefix? inet:ip-prefix
| | +--:(bgp)
| | | +--ro bgp? inet:ip-prefix
| | +--:(tunnel)
| | | +--ro tunnel-interface? uint32
| | +--:(pw)
| | | +--ro remote-pe-address? inet:ip-address
| | | +--ro pw-id? uint32
| | +--:(vpls)
| | | +--ro route-distinguisher? uint64
| | | +--ro sender-ve-id? uint16
| | | +--ro receiver-ve-id? uint16
| | +--:(mpls-mldp)
| | +--ro (root-address)?
| | +--:(ip-address)
| | | +--ro source-address? inet:ip-address
| | | +--ro group-ip-address? inet:ip-address
| | +--:(vpn)
| | | +--ro as-number? inet:as-number
| | +--:(global-id)
| | +--ro lsp-id? string
| +--ro system-info
| +--ro system-id? router-id
+--ro timestamp-type? uint32
+--ro timestamp-sec? uint32
+--ro timestamp-nanosec? uint32
+--ro ingress-intf-name? if:interface-ref
+--ro egress-intf-name? if:interface-ref
+--ro queue-depth? uint32
+--ro transit-delay? uint32
+--ro app-meta-data? uint64
data hierarchy of OAM Retrieval Methods
<CODE BEGINS> file "ietf-connectionless-oam-methods@2017-08-30.yang"
module ietf-connectionless-oam-methods {
namespace "urn:ietf:params:xml:ns:yang:ietf-connectionless-oam-methods";
prefix coam-methods;
import ietf-interfaces {
prefix if;
}
import ietf-connectionless-oam {
prefix coam;
}
organization
"IETF LIME Working Group";
contact
"Deepak Kumar dekumar@cisco.com
Qin Wu bill.wu@huawei.com
S Raghavan srihari@cisco.com
Zitao Wang wangzitao@huawei.com
R Rahman rrahman@cisco.com";
description
"This YANG module defines the RPCs for
connectionless OAM to be used within IETF
in a protocol Independent manner.
Functional level abstraction is indendent with
YANG modeling. It is assumed that each protocol maps
corresponding abstracts to its native format.
Each protocol may extend the YANG model defined
here to include protocol specific extensions";
revision 2017-08-30 {
description
"02 version";
reference "draft-ietf-lime-yang-connectionless-oam-methods";
}
rpc continuity-check {
if-feature "coam:continuity-check";
description
"Generates continuity-check as per RFC7276.";
input {
container destination-tp {
uses coam:tp-address;
description
"Destination test point.";
}
uses coam:session-type;
leaf source-interface {
type if:interface-ref;
description
"Source interface.";
}
leaf outbound-interface {
type if:interface-ref;
description
"Outbound interface.";
}
leaf count {
type empty;
description
"Specifies the number of
packets that will be sent.";
}
leaf vrf {
type coam:routing-instance-ref;
description
"VRF instance.";
}
leaf ttl {
type uint8;
default "255";
description
"Time to live (TTL).";
}
leaf packet-size {
type uint32 {
range "64..10000";
}
default "64";
description
"Size of ping echo request
packets, in octets";
}
}
output {
list error-code-list {
key "response-index";
leaf response-index {
type uint32;
description
"Response index.";
}
leaf status-code {
type int32;
description
"Error code is ";
}
leaf status-sub-code {
type uint8;
description
"Sub code.";
}
description
"Error code list.";
}
uses coam:continuity-check-data;
}
}
rpc path-discovery {
if-feature "coam:path-discovery";
description
"Generates path discovery as per RFC7276.";
input {
container destination-tp {
uses coam:tp-address;
description
"Destination test point.";
}
uses coam:session-type;
leaf source-interface {
type if:interface-ref;
description
"Source interface.";
}
leaf outbound-interface {
type if:interface-ref;
description
"Outbound interface.";
}
leaf vrf {
type coam:routing-instance-ref;
description
"VRF";
}
leaf max-ttl {
type uint8;
default "255";
description
"Max ttl.";
}
}
output {
list response-list {
key "response-index";
description
"Path discovery response list.";
leaf response-index {
type uint32;
description
"Response index.";
}
leaf status-code {
type int32;
description
"Error code is ";
}
leaf status-sub-code {
type uint8;
description
"Sub code is ";
}
}
uses coam:path-discovery-data;
}
}
}
<CODE ENDS>
The YANG module defined in this document is designed to be accessed via network management protocols such as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer is the secure transport layer, and the mandatory-to-implement secure transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer is HTTPS, and the mandatory-to-implement secure transport is TLS [RFC5246].
The NETCONF access control model [RFC6536] provides the means to restrict access for particular NETCONF or RESTCONF users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content.
Some of the RPC operations in this YANG module may be considered sensitive or vulnerable in some network environments. It is thus important to control access to these operations. These are the operations and their sensitivity/vulnerability:
which may lead to Denial-of-Service attack on both the local device and the network or unauthorized source access to some sensitive information.
This document registers a URI in the IETF XML registry [RFC3688]. Following the format in [RFC3688], the following registration is requested to be made:
URI: urn:ietf:params:xml:ns:yang:ietf-connectionless-oam-methods
Registrant Contact: The IESG.
XML: N/A, the requested URI is an XML namespace.
This document registers a YANG module in the YANG Module Names registry [RFC6020].
name: ietf-connectionless-oam-methods
namespace: urn:ietf:params:xml:ns:yang:ietf-connectionless-oam-methods
prefix: coam-methods
reference: RFC XXXX
| [I-D.ietf-netconf-yang-push] | Clemm, A., Voit, E., Prieto, A., Tripathy, A., Nilsen-Nygaard, E., Bierman, A. and B. Lengyel, "Subscribing to YANG datastore push updates", Internet-Draft draft-ietf-netconf-yang-push-08, August 2017. |
| [RFC4443] | Conta, A., Deering, S. and M. Gupta, "Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification", STD 89, RFC 4443, DOI 10.17487/RFC4443, March 2006. |
| [RFC5880] | Katz, D. and D. Ward, "Bidirectional Forwarding Detection (BFD)", RFC 5880, DOI 10.17487/RFC5880, June 2010. |
| [RFC7276] | Mizrahi, T., Sprecher, N., Bellagamba, E. and Y. Weingarten, "An Overview of Operations, Administration, and Maintenance (OAM) Tools", RFC 7276, DOI 10.17487/RFC7276, June 2014. |
| [RFC8029] | Kompella, K., Swallow, G., Pignataro, C., Kumar, N., Aldrin, S. and M. Chen, "Detecting Multiprotocol Label Switched (MPLS) Data-Plane Failures", RFC 8029, DOI 10.17487/RFC8029, March 2017. |
The following is an example of extensions possible to "ietf-connectionless-oam-methods" YANG model defined in this document.
The snippet below depicts an example of augmenting the "ietf-connectionless-oam-methods" YANG model with ICMP ping attributes:
augment "/coam-methods:continutiy-check"
+"/coam-methods:output"{
container session-rtt-statistics{
leaf min-rtt{
type uint32;
description
"This minimum ping round-trip-time(RTT) received.";
}
leaf max-rtt{
type uint32;
description
"This maximum ping round-trip-time(RTT) received.";
}
leaf avg-rtt{
type uint32;
description
"The current average ping round-trip-time(RTT)";
}
description
"This container presents the ping round-trip-time statistics.";
}
}
The following is an example related to the YANG model defined in this document. The example discusses persistent methods.
The persistent RPC operations are commands to trigger persistent continuity check or path discovery OAM while specifying the options for data-export from the device. Internet Protocol Flow Information Export (IPFIX) [RFC7011] or YANG-push [I-D.ietf-netconf-yang-push]. are currently outlined here as data export options and more can be added in future. It should be noted that the persistent methods are used to trigger create, modify and delete the persistent state associated with the data export options. The data export specific configurations are beyond the scope of this document.
module example-cl-oam-persistent-methods {
namespace "http://example.com/cl-oam-persistent-methods";
prefix pcoam-methods;
import ietf-interfaces {
prefix if;
}
import ietf-connectionless-oam {
prefix coam;
}
import ietf-yang-types {
prefix yang;
}
identity export-method {
description
"Base identity to represent a conceptual export-method.";
}
identity ipfix-export {
base export-method;
description
"IPFIX based export. Configuration provided separately.";
}
identity yang-push-export {
base export-method;
description
"Yang-push from draft-ietf-netconf-yang-push";
}
typedef export-method {
type identityref {
base export-method;
}
description
"Export method type.";
}
typedef change-type {
type enumeration {
enum "create" {
description
"Change due to a create.";
}
enum "delete" {
description
"Change due to a delete.";
}
enum "modify" {
description
"Change due to an update.";
}
}
description
"Different types of changes that may occur.";
}
rpc cc-persistent-create {
if-feature "coam:continuity-check";
description
"Generates persistent continuity-check.";
input {
container destination-tp {
uses coam:tp-address;
description
"Destination test point.";
}
uses coam:session-type;
leaf source-interface {
type if:interface-ref;
description
"Source interface.";
}
leaf outbound-interface {
type if:interface-ref;
description
"Outbound interface.";
}
leaf vrf {
type coam:routing-instance-ref;
description
"VRF instance.";
}
leaf ttl {
type uint8;
default "255";
description
"Time to live (TTL).";
}
leaf data-export-method {
type export-method;
description
"Type of export.";
}
choice cc-trigger {
description
"Defines necessary conditions for
periodic or on-change trigger.";
case periodic {
description
"Periodic reports.";
leaf period {
type yang:timeticks;
description
"Time interval between reports.";
}
leaf start-time {
type yang:date-and-time;
description
"Timestamp from which reports are started.";
}
}
case on-change {
description
"On-change trigger and not periodic.";
leaf all-data-on-start {
type boolean;
description
"Full update needed on start or not.";
}
leaf-list excluded-change {
type change-type;
description
"Restrict which changes trigger an update.";
}
}
}
}
output {
list error-code-list {
key "response-index";
leaf response-index {
type uint32;
description
"Response index.";
}
leaf status-code {
type int32;
description
"Error code.";
}
leaf status-sub-code {
type uint8;
description
"Sub code.";
}
description
"Error code list.";
}
leaf cc-persistent-id {
type string;
description
"Id to act as a cookie.";
}
}
}
rpc cc-persistent-modify {
if-feature "coam:continuity-check";
description
"Modifies persistent continuity-check
as per RFC7276.";
input {
leaf cc-persistent-id {
type string;
description
"Cookie Id to be used for modifications.";
}
leaf data-export-method {
type export-method;
description
"Type of export to use.";
}
choice cc-trigger {
description
"Defines necessary conditions for
periodic or on-change trigger.";
case periodic {
description
"Periodic reports.";
leaf period {
type yang:timeticks;
description
"Time interval between reports.";
}
leaf start-time {
type yang:date-and-time;
description
"Timestamp from which reports are started.";
}
}
case on-change {
description
"On-change trigger and not periodic.";
leaf all-data-on-start {
type boolean;
description
"Full update needed on start or not.";
}
leaf-list excluded-change {
type change-type;
description
"Restrict which changes trigger an update.";
}
}
}
}
output {
list error-code-list {
key "response-index";
leaf response-index {
type uint32;
description
"Response index.";
}
leaf status-code {
type int32;
description
"Error code";
}
leaf status-sub-code {
type uint8;
description
"Sub code.";
}
description
"Error code list.";
}
leaf cc-persistent-id {
type string;
description
"Id to represent a cookie.";
}
}
}
rpc cc-persistent-delete {
if-feature "coam:continuity-check";
description
"Deletes persistent continuity-check as per RFC7276.";
input {
leaf cc-persistent-id {
type string;
description
"Cookie Id to be used in deletion.";
}
}
output {
list error-code-list {
key "response-index";
leaf response-index {
type uint32;
description
"Response index.";
}
leaf status-code {
type int32;
description
"Error code.";
}
leaf status-sub-code {
type uint8;
description
"Sub code.";
}
description
"Error code list.";
}
}
}
rpc pd-persistent-create {
description
"Generates persistent path discovery.";
input {
container destination-tp {
uses coam:tp-address;
description
"Destination test point.";
}
uses coam:session-type;
leaf source-interface {
type if:interface-ref;
description
"Source interface.";
}
leaf outbound-interface {
type if:interface-ref;
description
"Outbound interface.";
}
leaf vrf {
type coam:routing-instance-ref;
description
"VRF";
}
leaf max-ttl {
type uint8;
default "255";
description
"Max ttl.";
}
leaf data-export-method {
type export-method;
description
"Type of export.";
}
choice pd-trigger {
description
"Defines necessary conditions
for periodic or on-change
trigger.";
case periodic {
description
"Periodic reports.";
leaf period {
type yang:timeticks;
description
"Time interval between reports.";
}
leaf start-time {
type yang:date-and-time;
description
"Timestamp from which reports are started.";
}
}
case on-change {
description
"On-change trigger and not periodic.";
leaf all-data-on-start {
type boolean;
description
"Full update needed on start or not.";
}
leaf-list excluded-change {
type change-type;
description
"Restrict which changes trigger an update.";
}
}
}
}
output {
list response-list {
key "response-index";
description
"Path discovery response list.";
leaf response-index {
type uint32;
description
"Response index.";
}
leaf status-code {
type int32;
description
"Error code is ";
}
leaf status-sub-code {
type uint8;
description
"Sub code is ";
}
leaf pd-persistent-id {
type string;
description
"Id to act as a cookie.";
}
}
}
}
rpc pd-persistent-modify {
description
"Modifies persistent path discovery.";
input {
leaf pd-persistent-id {
type string;
description
"Cookie Id to be used for modifications.";
}
leaf data-export-method {
type export-method;
description
"Type of export.";
}
choice pd-trigger {
description
"Defines necessary conditions for periodic or on-change
trigger.";
case periodic {
description
"Periodic reports.";
leaf period {
type yang:timeticks;
description
"Time interval between reports.";
}
leaf start-time {
type yang:date-and-time;
description
"Timestamp from which reports are started.";
}
}
case on-change {
description
"On-change trigger and not periodic.";
leaf all-data-on-start {
type boolean;
description
"Full update needed on start or not.";
}
leaf-list excluded-change {
type change-type;
description
"Restrict which changes trigger an update.";
}
}
}
}
output {
list response-list {
key "response-index";
description
"path discovery response list.";
leaf response-index {
type uint32;
description
"response index.";
}
leaf status-code {
type int32;
description
"error code is ";
}
leaf status-sub-code {
type uint8;
description
"sub code is ";
}
leaf pd-persistent-id {
type string;
description
"Id to act as a cookie.";
}
}
}
}
rpc pd-persistent-delete {
description
"Deletes persistent path discovery.";
input {
leaf pd-persistent-id {
type string;
description
"Cookie Id to be used in deletion.";
}
}
output {
list response-list {
key "response-index";
description
"path discovery response list.";
leaf response-index {
type uint32;
description
"response index.";
}
leaf status-code {
type int32;
description
"error code is ";
}
leaf status-sub-code {
type uint8;
description
"sub code is ";
}
}
}
}
}