| PWE3 | T. Nadeau |
| Internet-Draft | lucidvision |
| Intended status: Standards Track | L. Martini |
| Expires: August 3, 2015 | S. Bryant |
| Cisco Systems | |
| January 30, 2015 |
Using GAL as a VCCV Channel Indicator
draft-ietf-pals-vccv-for-gal-01
This document specifies a new Virtual Circuit Connectivity Verification (VCCV) (RFC5085) control channel type for use with pseudowires (PW) carried over an MPLS network. This new channel type uses the Generic Associated Channel Label (GAL) (RFC5586) to distinguish VCCV packets from packets carrying user data.
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 3, 2015.
Copyright (c) 2015 IETF Trust and the persons identified as the document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.
This document specifies a new Virtual Circuit Connectivity Verification (VCCV) [RFC5085] control channel (CC) type for use with pseudowires (PW) carried over an MPLS network that do not use the PW Control Word (CW) [RFC4385]. This new VCCV CC type uses the Generic Associated Channel Label (GAL) [RFC5586] to distinguish VCCV packets from packets carrying user data. This new VCCV CC type introduces compatibility with the method of MPLS Label Switched Path (LSP) Operations, Administration, and Maintenance (OAM) identification, particularly in MPLS-TP networks [RFC5921].
VCCV currently specifies three CC types. VCCV CC Type 1 uses the PW Control Word (CW) to distinguish VCCV packets from packets carrying user data. VCCV CC Types 2 and 3 require IP encapsulation for OAM packets they carry. This was not an issue when [RFC5085] was designed, but is in conflict with the design goals of MPLS-TP [RFC5921] which does not otherwise require the availability of IP. VCCV CC Type 2 is not applicable to multi-segment PWs (MS-PWs) [RFC6073]. A MS-PW operating without the CW therefore has to use VCCV CC Type 3 which identifies VCCV packets on the basis of TTL expiry. Whilst less of an issue with a single segment PW (SS-PW), on an MS-PW this need to be accurately set to cause TTL expiry at the egress Terminating Provider Edge (T-PE) [RFC6073]. In the event of a error in the setting of the PW LSE TTL this can result in VCCV packets leaking into the attachment circuit which may disrupt the operation of the PW, or the user service, and is a security risk. The new VCCV CC type defined in this specification addresses these problems for PWs that do not use the CW.
Note that VCCV CC Type 3 remains mandatory for multi-segment PW (MS-PW) OAM and it is currently combined with VCCV CC Type 1 for MS-PWs that use the CW [RFC6073]. This specification enables the combination of VCCV CC Type 3 with VCCV Type 4 for PWs that do not support the CWSection 5.
For reasons of network efficiency and due to hardware constraints it is not possible to address these issue by mandating that all PWs use the PW CW, hence the introduction of this new VCCV CC type. PWs without the CW are widely deployed, and hence mandating that all PWs use the CW is not a viable way to address this issue.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119].
When the PW CW is not used, the GAL VCCV Control Channel (CC) type defined in this section MAY be used. This is referred to as VCCV CC Type4 throughout the rest of this of this document. VCCV Type 4 uses the encapsulation shown in Figure 1.
0 1
2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PW LSE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| GAL LSE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0 0 0 1|Version| Reserved | Channel Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ VCCV Message Body ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1
The VCCV message body is preceded by a Generic Associated Channel Header as defined in [RFC5586], in which the Channel Type identifies the type and format of the OAM message carried in the VCCV message body.
The GAL LSE MUST contain the GAL reserved label as defined in [RFC5586].
The PW LSE is constructed according to the existing procedures that apply to the type of pseudowire that is in use.
Note that the inclusion of a GAL following the PW LSE over a label switched path subject to Equal-Cost Multi-path (ECMP) load balancing can cause the OAM packet to take a different path through the network from the corresponding PW data packets. If that is not acceptable, then an alternative VCCV type MUST be used.
[RFC6391] specifies that when the flow-aware transport (FAT) of pseudowires over an MPLS packet switched network has been signalled or configured, the Flow LSE MUST be present. It further specifies that "the flow label MUST NOT be an MPLS reserved label (values in the range 0..15) [RFC3032]", and that "If a flow LSE is present, it MUST be checked to determine whether it carries a reserved label. If it is a reserved label, the packet is processed according to the rules associated with that reserved label; otherwise, the LSE is discarded."
This document specifies that if the flow-aware transport of pseudowires over an MPLS packet switched network has been signalled or configured then the presence of VCCV message is indicated by the use of a GAL in place of the flow LSE.
This is consistent with [RFC6391], and the packet structure is identical to that shown in Figure 1.
Note that the use of a GAL in place of the flow label over a label switched path subject to ECMP can cause the OAM packet to take a different path through the network from the corresponding PW data packets. If that is not acceptable, then an alternative VCCV type MUST be used.
When using VCCV CC Type 4 for MS-PWs, a PE transmitting the VCCV packet to a Switching PE (S-PE) MUST set the TTL to the appropriate value to expire at that S-PE. An S-PE that supports this specification MUST inspect packets PW packet that are received as a result of TTL expiry, determine whether a GAL follows the PW LSE. If a GAL is present the S-PE then processes the VCCV packet.
An S-PE that does not support this specification would be expected to reject as malformed a VCCV CC Type 4 packet that was received. This is because the S-PE would expect the PW LSE to be bottom of stack (the non FAT case) and for the LSE at bottom of stack not to be a reserved label (both the FAT and the non-FAT cases). An S-PE that did not make this reserved label check would then find that the first nibble following the label stack was 0x1 and not the expected start of an IP packet. It would hence be expected to also reject the packet. This update to the behaviour of S-PEs is therefore backwards compatible.
The VCCV capability advertisement MUST match the c-bit setting that is advertised in the PW FEC element [RFC4447]. If the c-bit is set, indicating the use of the PW CW, then VCCV CC Type 4 MUST NOT be advertised. If the c-bit is not set, indicating that the PW CW is not in use, then an equipment supporting this specification MUST advertise VCCV CC Type 4. Advertisement of VCCV CC Types 1 and 4 are therefore mutually exclusive.
A PE supporting VCCV CC Type 4 MAY advertise other VCCV CC types as defined in [RFC5085] .
If the remote PE supports VCCV CC Type 4, and the PW CW is not in use, then the following capability advertisement precedence rules supersede those defined in Section 7 of [RFC5085] :
If the remote PE finds that VCCV CC Types 1 and 4 are both advertised, or that c-bit is set and VCCV CC Type 4 is advertised, then it should report the error to the operator through the management interface in use, and send a Label Release Message with a status code "VCCV Type Error".
Whilst the introduction of this additional VCCV CC type increases the number of VCCV CC types that the operator needs to manage, it addresses the issues with VCCV CC Types 2 and 3 described in . [INTRO].
In the event of a misconfiguration of this VCCV CC type, the PW is taken out of service and the operator advised as described in Section 6.
Attention is drawn to the possible absence of fate sharing between PW data packets and VCCV CC Type 4 packets described in Section 3 and Section 4.
This document does not by itself raise any new security considerations beyond those described in [RFC5085]. It addresses the possibility of packet leaking that can occur with VCCV CC Type 3.
IANA is requested to assign a new bit from the MPLS VCCV Control Channel (CC) Types registry in the PWE3-parameters name space in order to identify VCCV type 4. It is recommended that Bit 3 be assigned to this purpose which would have a value of 0x08.
MPLS VCCV Control Channel (CC) Types
Bit (Value) Description Reference
============ =========== ==================
Bit X (0x0Y) Type 4 This Specification
IANA is requested to assign a new Status Code from the Label Distribution Protocol (LDP) Parameters name space:
Status Code Name Space
Range/Value E Description Reference
=========== = =============== =========
0x000000xx 0 VCCV Type Error This Specification
The authors wish to thank Alexander (Sasha) Vainshtein for his review comments and for his proposal to make the GAL and Flow labels mutually exclusive. This proposal let to a significant simplification of this design.
| [RFC5921] | Bocci, M., Bryant, S., Frost, D., Levrau, L. and L. Berger, "A Framework for MPLS in Transport Networks", RFC 5921, July 2010. |