| PCE Working Group | A. Koushik |
| Internet-Draft | Brocade Communications Inc. |
| Intended status: Standards Track | E. Stephan |
| Expires: April 27, 2015 | Orange |
| Q. Zhao | |
| Huawei Technology | |
| D. King | |
| Old Dog Consulting | |
| J. Hardwick | |
| Metaswitch | |
| October 24, 2014 |
Path Computation Element Communications Protocol (PCEP) Management Information Base (MIB) Module
draft-ietf-pce-pcep-mib-11
This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects for modeling of Path Computation Element communications Protocol (PCEP) for communications between a Path Computation Client (PCC) and a Path Computation Element (PCE), or between two PCEs.
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 27, 2015.
Copyright (c) 2014 IETF Trust and the persons identified as the document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.
The Path Computation Element (PCE) defined in [RFC4655] is an entity that is capable of computing a network path or route based on a network graph, and applying computational constraints. A Path Computation Client (PCC) may make requests to a PCE for paths to be computed.
PCEP is the communication protocol between a PCC and PCE and is defined in [RFC5440]. PCEP interactions include path computation requests and path computation replies as well as notifications of specific states related to the use of a PCE in the context of Multiprotocol Label Switching (MPLS) and Generalized MPLS (GMPLS) Traffic Engineering (TE).
This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it defines a MIB module that can be used to monitor PCEP interactions between a PCC and a PCE, or between two PCEs.
The scope of this document is to provide a MIB module for the PCEP base protocol defined in [RFC5440]. Extensions to the PCEP base protocol are beyond the scope for this document.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY" and "OPTIONAL" in this document are to be interpreted as described in BCP 14, RFC 2119 [RFC2119].
This document uses the terminology defined in [RFC4655] and [RFC5440]. In particular, it uses the following acronyms.
This document uses the term "PCEP entity" to refer to a local PCEP speaker, "peer" to refer to a remote PCEP speaker and "PCEP speaker" where it is not necessary to distinguish between local and remote.
For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579], and STD 58, RFC 2580 [RFC2580].
The PCEP MIB module contains the following information:
The PCEP MIB module is limited to "read-only" access except for pcePcepNotificationsMaxRate, which is used to throttle the rate at which the implementation generates notifications.
The PCEP MIB module may contain status information for multiple logical local PCEP entities. There are several scenarios in which there may be more than one local PCEP entity, including the following.
The pcePcepEntityTable contains one row for each local PCEP entity. Each row is read-only and contains current status information plus the PCEP entity's running configuration.
The pcePcepEntityTable is indexed by pcePcepEntityIndex, which also acts as the primary index for the other tables in this MIB module.
The pcePcepPeerTable contains one row for each peer that the local PCEP entity knows about. Each row is read-only and contains information to identify the peer, the running configuration relating to that peer and statistics that track the messages exchanged with that peer and its response times.
A PCEP speaker is identified by its IP address. If there is a PCEP speaker in the network that uses multiple IP addresses then it looks like multiple distinct peers to the other PCEP speakers in the network.
The pcePcepPeerTable is indexed first by pcePcepEntityIndex, then by pcePcepPeerAddrType and pcePcepPeerAddr. This indexing structure allows each local PCEP entity to report its own set of peers.
Since PCEP sessions can be ephemeral, the pcePcepPeerTable tracks a peer even when no PCEP session currently exists to that peer. The statistics contained in pcePcepPeerTable are an aggregate of the statistics for all successive sessions to that peer.
To limit the quantity of information that is stored, an implementation MAY choose to discard a row from the pcePcepPeerTable if and only if no PCEP session exists to the corresponding peer.
The pcePcepSessTable contains one row for each PCEP session that the PCEP entity (PCE or PCC) is currently participating in. Each row is read-only and contains the running configuration that is applied to the session, plus identifiers and statistics for the session.
The statistics in pcePcepSessTable are semantically different from those in pcePcepPeerTable since the former apply to the current session only, whereas the latter are the aggregate for all sessions that have existed to that peer.
Although [RFC5440] forbids there from being more than one active PCEP session between a given pair of PCEP entities at any one time, there is a window during session establishment where the pcePcepSessTable may contain two rows for a given peer, one representing a session initiated by the local PCEP entity and one representing a session initiated by the peer. If either of these sessions reaches active state, then the other is discarded.
The pcePcepSessTable is indexed first by pcePcepEntityIndex, then by pcePcepPeerAddrType and pcePcepPeerAddr, and finally by pcePcepSessInitiator. This indexing structure allows each local PCEP entity to report its own set of active sessions. The pcePcepSessInitiator index allows two rows to exist transiently for a given peer, as discussed above.
The PCEP MIB module contains notifications for the following conditions.
The PCEP MIB module imports the following textual conventions from the INET-ADDRESS-MIB defined in RFC 4001 [RFC4001]:
PCEP relies on existing protocols which have specialized MIB objects to monitor their own activities. Consequently this document considers that the monitoring of underlying protocols is out of scope of the PCEP MIB module.
Index by:
pcePcepEntityIndex
+--------------+ Index by:
|pcePcepEntity | pcePcepEntityIndex,
|Table | pcePcepPeerAddrType,
+--------------+ pcePcepPeerAddr
|pcePcepEntity |
|Entry |<----*
+--------------+ | +------------+ Index by:
| | | |pcePcepPeer | pcePcepEntityIndex,
| |<-* | |Table | pcePcepPeerAddrType,
+--------------+ | | +------------+ pcePcepPeerAddr,
| *--|PcePcepPeer | pcePcepSessInitiator
| | |Entry |<-----*
| | +------------+ | +------------+
| *--| | | |pcePcepSess |
| | |<----*| |Table |
| +------------+ || +------------+
*-----| | |*-|pcePcepSess |
| | |<--* | |Entry |
| +------------+ | | +------------+
*-----| | | *--| |
| [1] | | | |
+------------+ | +------------+
*----| |
| | |
| +------------+
*----| [2] |
| |
+------------+
[1]: A peer entry with no current session
[2]: Two sessions exist during a window in session
initialization.
The following diagram illustrates the relationships between the pcePcepEntityTable, pcePcepPeerTable and pcePcepSessTable.
PCE-PCEP-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
mib-2,
NOTIFICATION-TYPE,
Unsigned32,
Counter32
FROM SNMPv2-SMI -- RFC 2578
TruthValue,
TimeStamp
FROM SNMPv2-TC -- RFC 2579
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF -- RFC 2580
InetAddressType,
InetAddress
FROM INET-ADDRESS-MIB; -- RFC 4001
pcePcepMIB MODULE-IDENTITY
LAST-UPDATED
"201410241200Z" -- 24 October 2014
ORGANIZATION
"IETF Path Computation Element (PCE) Working Group"
CONTACT-INFO
"Email: pce@ietf.org
WG charter:
http://www.ietf.org/html.charters/pce-charter.html"
DESCRIPTION
"This MIB module defines a collection of objects for managing
Path Computation Element communications Protocol (PCEP).
Copyright (C) The IETF Trust (2014). This version of this
MIB module is part of RFC YYYY; see the RFC itself for full
legal notices."
-- RFC Ed,: replace YYYY with actual RFC number & remove this note
REVISION
"201410241200Z" -- 24 October 2014
DESCRIPTION
"Initial version, published as RFC YYYY."
-- RFC Ed.: replace YYYY with actual RFC number & remove this note
::= { mib-2 XXX }
-- RFC Ed.: replace XXX with IANA-assigned number & remove this note
pcePcepNotifications OBJECT IDENTIFIER ::= { pcePcepMIB 0 }
pcePcepObjects OBJECT IDENTIFIER ::= { pcePcepMIB 1 }
pcePcepConformance OBJECT IDENTIFIER ::= { pcePcepMIB 2 }
--
-- PCEP Entity Objects
--
pcePcepEntityTable OBJECT-TYPE
SYNTAX SEQUENCE OF PcePcepEntityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about local PCEP entities.
The entries in this table are read-only."
::= { pcePcepObjects 1 }
pcePcepEntityEntry OBJECT-TYPE
SYNTAX PcePcepEntityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This entry represents a local PCEP entity."
INDEX { pcePcepEntityIndex }
::= { pcePcepEntityTable 1 }
PcePcepEntityEntry ::= SEQUENCE {
pcePcepEntityIndex Unsigned32,
pcePcepEntityAdminStatus INTEGER,
pcePcepEntityOperStatus INTEGER,
pcePcepEntityAddrType InetAddressType,
pcePcepEntityAddr InetAddress,
pcePcepEntityConnectTimer Unsigned32,
pcePcepEntityConnectMaxRetry Unsigned32,
pcePcepEntityInitBackoffTimer Unsigned32,
pcePcepEntityMaxBackoffTimer Unsigned32,
pcePcepEntityOpenWaitTimer Unsigned32,
pcePcepEntityKeepWaitTimer Unsigned32,
pcePcepEntityKeepAliveTimer Unsigned32,
pcePcepEntityDeadTimer Unsigned32,
pcePcepEntityAllowNegotiation TruthValue,
pcePcepEntityMaxKeepAliveTimer Unsigned32,
pcePcepEntityMaxDeadTimer Unsigned32,
pcePcepEntityMinKeepAliveTimer Unsigned32,
pcePcepEntityMinDeadTimer Unsigned32,
pcePcepEntitySyncTimer Unsigned32,
pcePcepEntityRequestTimer Unsigned32,
pcePcepEntityMaxSessions Unsigned32,
pcePcepEntityMaxUnknownReqs Unsigned32,
pcePcepEntityMaxUnknownMsgs Unsigned32
}
pcePcepEntityIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This index is used to uniquely identify the PCEP entity."
::= { pcePcepEntityEntry 1 }
pcePcepEntityAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
adminStatusUp(1),
adminStatusDown(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The administrative status of this PCEP Entity.
This is the desired operational status as currently set by
an operator or by default in the implementation. The value
of pcePcepEntityOperStatus represents the current status of
an attempt to reach this desired status."
::= { pcePcepEntityEntry 2 }
pcePcepEntityOperStatus OBJECT-TYPE
SYNTAX INTEGER {
operStatusUp(1),
operStatusDown(2),
operStatusGoingUp(3),
operStatusGoingDown(4),
operStatusFailed(5),
operStatusFailedPerm(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The operational status of the PCEP entity. Takes one of the
following values.
- operStatusUp(1): the PCEP entity is active.
- operStatusDown(2): the PCEP entity is inactive.
- operStatusGoingUp(3): the PCEP entity is activating.
- operStatusGoingDown(4): the PCEP entity is deactivating.
- operStatusFailed(5): the PCEP entity has failed and will
recover when possible.
- operStatusFailedPerm(6): the PCEP entity has failed and
will not recover without operator intervention."
::= { pcePcepEntityEntry 3 }
pcePcepEntityAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the PCEP entity's Internet address. This object
specifies how the value of the pcePcepEntityAddr object
should be interpreted. Only values unknown(0), ipv4(1), or
ipv6(2) are supported."
::= { pcePcepEntityEntry 4 }
pcePcepEntityAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local Internet address of this PCEP entity. The type is
given by pcePcepEntityAddrType.
If operating as a PCE server, the PCEP entity listens on
this address. If operating as a PCC, the PCEP entity binds
outgoing TCP connections to this address.
It is possible for the PCEP entity to operate both as a PCC
and a PCE Server, in which case it uses this address both to
listen for incoming TCP connections and to bind outgoing
TCP connections."
::= { pcePcepEntityEntry 5 }
pcePcepEntityConnectTimer OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time that the PCEP entity will wait to establish a TCP
connection with a peer. If a TCP connection is not
established within this time then PCEP aborts the session
setup attempt."
::= { pcePcepEntityEntry 6 }
pcePcepEntityConnectMaxRetry OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of times the system tries to establish
a TCP connection to a peer before the session with the peer
transitions to the idle state.
When the session transitions to the idle state:
- pcePcepPeerSessionExists transitions to false(2)
- the associated PcePcepSessEntry is deleted
- a backoff timer runs before the session is tried again."
::= { pcePcepEntityEntry 7 }
pcePcepEntityInitBackoffTimer OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The initial back-off time for retrying a failed session
setup attempt to a peer.
The back-off time increases for each failed session setup
attempt, until a maximum back-off time is reached. The
maximum back-off time is pcePcepEntityMaxBackoffTimer."
::= { pcePcepEntityEntry 8 }
pcePcepEntityMaxBackoffTimer OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum back-off time for retrying a failed session
setup attempt to a peer.
The back-off time increases for each failed session setup
attempt, until this maximum value is reached. Session
setup attempts then repeat periodically without any
further increase in back-off time."
::= { pcePcepEntityEntry 9 }
pcePcepEntityOpenWaitTimer OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time that the PCEP entity will wait to receive an Open
message from a peer after the TCP connection has come up.
If no Open message is received within this time then PCEP
terminates the TCP connection and deletes the associated
PcePcepSessEntry."
::= { pcePcepEntityEntry 10 }
pcePcepEntityKeepWaitTimer OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time that the PCEP entity will wait to receive a
Keepalive or PCErr message from a peer during session
initialization after receiving an Open message. If no
Keepalive or PCErr message is received within this time then
PCEP terminates the TCP connection and deletes the
associated PcePcepSessEntry."
::= { pcePcepEntityEntry 11 }
pcePcepEntityKeepAliveTimer OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The keep alive transmission timer that this PCEP entity will
propose in the initial OPEN message of each session it is
involved in. This is the maximum time between two
consecutive messages sent to a peer. Zero means that
the PCEP entity prefers not to send Keepalives at all.
Note that the actual Keepalive transmission intervals, in
either direction of an active PCEP session, are determined
by negotiation between the peers as specified by RFC
5440, and so may differ from this configured value. For
the actually negotiated values (per-session), see
pcePcepSessKeepaliveTimer and
pcePcepSessPeerKeepaliveTimer."
::= { pcePcepEntityEntry 12 }
pcePcepEntityDeadTimer OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The dead timer that this PCEP entity will propose in the
initial OPEN message of each session it is involved in.
This is the time after which a peer should declare a
session down if it does not receive any PCEP messages.
Zero suggests that the peer does not run a dead timer at
all."
::= { pcePcepEntityEntry 13 }
pcePcepEntityAllowNegotiation OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Whether the PCEP entity will permit negotiation of session
parameters."
::= { pcePcepEntityEntry 14 }
pcePcepEntityMaxKeepAliveTimer OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"In PCEP session parameter negotiation, the maximum value
that this PCEP entity will accept from a peer for the
interval between Keepalive transmissions. Zero means that
the PCEP entity will allow no Keepalive transmission at
all."
::= { pcePcepEntityEntry 15 }
pcePcepEntityMaxDeadTimer OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"In PCEP session parameter negotiation, the maximum value
that this PCEP entity will accept from a peer for the Dead
timer. Zero means that the PCEP entity will allow not
running a Dead timer."
::= { pcePcepEntityEntry 16 }
pcePcepEntityMinKeepAliveTimer OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"In PCEP session parameter negotiation, the minimum value
that this PCEP entity will accept for the interval between
Keepalive transmissions. Zero means that the PCEP entity
insists on no Keepalive transmission at all."
::= { pcePcepEntityEntry 17 }
pcePcepEntityMinDeadTimer OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"In PCEP session parameter negotiation, the minimum value
that this PCEP entity will accept for the Dead timer. Zero
means that the PCEP entity insists on not running a Dead
timer."
::= { pcePcepEntityEntry 18 }
pcePcepEntitySyncTimer OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of SyncTimer is used in the case of synchronized
path computation request using the SVEC object.
Consider the case where a PCReq message is received by a PCE
that contains the SVEC object referring to M synchronized
path computation requests. If after the expiration of the
SyncTimer all the M path computation requests have not been
received, a protocol error is triggered and the PCE MUST
cancel the whole set of path computation requests.
The aim of the SyncTimer is to avoid the storage of unused
synchronized requests should one of them get lost for some
reasons (for example, a misbehaving PCC).
A value of zero is returned if and only if the entity does
not use the SyncTimer."
::= { pcePcepEntityEntry 19 }
pcePcepEntityRequestTimer OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum time that the PCEP entity will wait for a
response to a PCReq message."
::= { pcePcepEntityEntry 20 }
pcePcepEntityMaxSessions OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum number of sessions involving this PCEP entity
that can exist at any time."
::= { pcePcepEntityEntry 21 }
pcePcepEntityMaxUnknownReqs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of unrecognized requests and replies that
any session on this PCEP entity is willing to accept per
minute before terminating the session.
A PCRep message contains an unrecognized reply if it
contains an RP object whose request ID does not correspond
to any in-progress request sent by this PCEP entity.
A PCReq message contains an unrecognized request if it
contains an RP object whose request ID is zero."
::= { pcePcepEntityEntry 22 }
pcePcepEntityMaxUnknownMsgs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of unknown messages that any session
on this PCEP entity is willing to accept per minute before
terminating the session."
::= { pcePcepEntityEntry 23 }
--
-- The PCEP Peer Table
--
pcePcepPeerTable OBJECT-TYPE
SYNTAX SEQUENCE OF PcePcepPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about peers known by
the local PCEP entity. The entries in this table are
read-only.
This table gives peer information that spans PCEP
sessions. Information about current PCEP sessions can be
found in the pcePcepSessTable table."
::= { pcePcepObjects 2 }
pcePcepPeerEntry OBJECT-TYPE
SYNTAX PcePcepPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single peer which spans all PCEP
sessions to that peer."
INDEX { pcePcepEntityIndex,
pcePcepPeerAddrType,
pcePcepPeerAddr }
::= { pcePcepPeerTable 1 }
PcePcepPeerEntry ::= SEQUENCE {
pcePcepPeerAddrType InetAddressType,
pcePcepPeerAddr InetAddress,
pcePcepPeerRole INTEGER,
pcePcepPeerDiscontinuityTime TimeStamp,
pcePcepPeerInitiateSession TruthValue,
pcePcepPeerSessionExists TruthValue,
pcePcepPeerNumSessSetupOK Counter32,
pcePcepPeerNumSessSetupFail Counter32,
pcePcepPeerSessionUpTime TimeStamp,
pcePcepPeerSessionFailTime TimeStamp,
pcePcepPeerSessionFailUpTime TimeStamp,
pcePcepPeerAvgRspTime Unsigned32,
pcePcepPeerLWMRspTime Unsigned32,
pcePcepPeerHWMRspTime Unsigned32,
pcePcepPeerNumPCReqSent Counter32,
pcePcepPeerNumPCReqRcvd Counter32,
pcePcepPeerNumPCRepSent Counter32,
pcePcepPeerNumPCRepRcvd Counter32,
pcePcepPeerNumPCErrSent Counter32,
pcePcepPeerNumPCErrRcvd Counter32,
pcePcepPeerNumPCNtfSent Counter32,
pcePcepPeerNumPCNtfRcvd Counter32,
pcePcepPeerNumKeepaliveSent Counter32,
pcePcepPeerNumKeepaliveRcvd Counter32,
pcePcepPeerNumUnknownRcvd Counter32,
pcePcepPeerNumCorruptRcvd Counter32,
pcePcepPeerNumReqSent Counter32,
pcePcepPeerNumSvecSent Counter32,
pcePcepPeerNumSvecReqSent Counter32,
pcePcepPeerNumReqSentPendRep Counter32,
pcePcepPeerNumReqSentEroRcvd Counter32,
pcePcepPeerNumReqSentNoPathRcvd Counter32,
pcePcepPeerNumReqSentCancelRcvd Counter32,
pcePcepPeerNumReqSentErrorRcvd Counter32,
pcePcepPeerNumReqSentTimeout Counter32,
pcePcepPeerNumReqSentCancelSent Counter32,
pcePcepPeerNumReqSentClosed Counter32,
pcePcepPeerNumReqRcvd Counter32,
pcePcepPeerNumSvecRcvd Counter32,
pcePcepPeerNumSvecReqRcvd Counter32,
pcePcepPeerNumReqRcvdPendRep Counter32,
pcePcepPeerNumReqRcvdEroSent Counter32,
pcePcepPeerNumReqRcvdNoPathSent Counter32,
pcePcepPeerNumReqRcvdCancelSent Counter32,
pcePcepPeerNumReqRcvdErrorSent Counter32,
pcePcepPeerNumReqRcvdCancelRcvd Counter32,
pcePcepPeerNumReqRcvdClosed Counter32,
pcePcepPeerNumRepRcvdUnknown Counter32,
pcePcepPeerNumReqRcvdUnknown Counter32
}
pcePcepPeerAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of the peer's Internet address. This object
specifies how the value of the pcePcepPeerAddr object should
be interpreted. Only values unknown(0), ipv4(1), or
ipv6(2) are supported."
::= { pcePcepPeerEntry 1 }
pcePcepPeerAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Internet address of the peer. The type is given by
pcePcepPeerAddrType."
::= { pcePcepPeerEntry 2 }
pcePcepPeerRole OBJECT-TYPE
SYNTAX INTEGER {
unknown(0),
pcc(1),
pce(2),
pccAndPce(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The role that this peer took the last time a session was
established. Takes one of the following values.
- unknown(0): this peer's role is not known.
- pcc(1): this peer is a Path Computation Client (PCC).
- pce(2): this peer is a Path Computation Server (PCE).
- pccAndPce(3): this peer is both a PCC and a PCE."
::= { pcePcepPeerEntry 3 }
pcePcepPeerDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time that the information and
statistics in this row were last reset."
::= { pcePcepPeerEntry 4 }
pcePcepPeerInitiateSession OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether the local PCEP entity initiates sessions
to this peer, or waits for the peer to initiate a session."
::= { pcePcepPeerEntry 5 }
pcePcepPeerSessionExists OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether a session with this peer currently
exists."
::= { pcePcepPeerEntry 6 }
pcePcepPeerNumSessSetupOK OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCEP sessions successfully established with
the peer, including any current session. This counter is
incremented each time a session with this peer is
successfully established."
::= { pcePcepPeerEntry 7 }
pcePcepPeerNumSessSetupFail OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCEP sessions with the peer that have been
attempted but failed before being fully established.
This counter is incremented each time a session retry to
this peer fails."
::= { pcePcepPeerEntry 8 }
pcePcepPeerSessionUpTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime the last time a session with this
peer was successfully established.
If pcePcepPeerNumSessSetupOK is zero, then this object
contains zero."
::= { pcePcepPeerEntry 9 }
pcePcepPeerSessionFailTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime the last time a session with this
peer failed to be established.
If pcePcepPeerNumSessSetupFail is zero, then this object
contains zero."
::= { pcePcepPeerEntry 10 }
pcePcepPeerSessionFailUpTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime the last time a session with this
peer failed from active.
If pcePcepPeerNumSessSetupOK is zero, then this object
contains zero."
::= { pcePcepPeerEntry 11 }
pcePcepPeerAvgRspTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average response time for this peer.
If an average response time has not been calculated for this
peer then this object has the value zero.
If pcePcepPeerRole is pcc then this field is meaningless and
is set to zero."
::= { pcePcepPeerEntry 12 }
pcePcepPeerLWMRspTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The smallest (low-water mark) response time seen from this
peer.
If no responses have been received from this peer then this
object has the value zero.
If pcePcepPeerRole is pcc then this field is meaningless and
is set to zero."
::= { pcePcepPeerEntry 13 }
pcePcepPeerHWMRspTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The greatest (high-water mark) response time seen from this
peer.
If no responses have been received from this peer then this
object has the value zero.
If pcePcepPeerRole is pcc then this field is meaningless and
is set to zero."
::= { pcePcepPeerEntry 14 }
pcePcepPeerNumPCReqSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCReq messages sent to this peer."
::= { pcePcepPeerEntry 15 }
pcePcepPeerNumPCReqRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCReq messages received from this peer."
::= { pcePcepPeerEntry 16 }
pcePcepPeerNumPCRepSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCRep messages sent to this peer."
::= { pcePcepPeerEntry 17 }
pcePcepPeerNumPCRepRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCRep messages received from this peer."
::= { pcePcepPeerEntry 18 }
pcePcepPeerNumPCErrSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCErr messages sent to this peer."
::= { pcePcepPeerEntry 19 }
pcePcepPeerNumPCErrRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCErr messages received from this peer."
::= { pcePcepPeerEntry 20 }
pcePcepPeerNumPCNtfSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCNtf messages sent to this peer."
::= { pcePcepPeerEntry 21 }
pcePcepPeerNumPCNtfRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCNtf messages received from this peer."
::= { pcePcepPeerEntry 22 }
pcePcepPeerNumKeepaliveSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Keepalive messages sent to this peer."
::= { pcePcepPeerEntry 23 }
pcePcepPeerNumKeepaliveRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Keepalive messages received from this peer."
::= { pcePcepPeerEntry 24 }
pcePcepPeerNumUnknownRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of unknown messages received from this peer."
::= { pcePcepPeerEntry 25 }
pcePcepPeerNumCorruptRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of corrupted PCEP message received from this
peer."
::= { pcePcepPeerEntry 26 }
pcePcepPeerNumReqSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests sent to this peer. A request
corresponds 1:1 with an RP object in a PCReq message.
This might be greater than pcePcepPeerNumPCReqSent because
multiple requests can be batched into a single PCReq
message."
::= { pcePcepPeerEntry 27 }
pcePcepPeerNumSvecSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of SVEC objects sent to this peer in PCReq
messages. An SVEC object represents a set of synchronized
requests."
::= { pcePcepPeerEntry 28 }
pcePcepPeerNumSvecReqSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests sent to this peer that appeared in
one or more SVEC objects."
::= { pcePcepPeerEntry 29 }
pcePcepPeerNumReqSentPendRep OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that have been sent to this peer for
which a response is still pending."
::= { pcePcepPeerEntry 30 }
pcePcepPeerNumReqSentEroRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that have been sent to this peer for
which a response with an ERO object was received. Such
responses indicate that a path was successfully computed by
the peer."
::= { pcePcepPeerEntry 31 }
pcePcepPeerNumReqSentNoPathRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that have been sent to this peer for
which a response with a NO-PATH object was received. Such
responses indicate that the peer could not find a path to
satisfy the request."
::= { pcePcepPeerEntry 32 }
pcePcepPeerNumReqSentCancelRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that were cancelled by the peer with
a PCNtf message.
This might be different than pcePcepPeerNumPCNtfRcvd because
not all PCNtf messages are used to cancel requests, and a
single PCNtf message can cancel multiple requests."
::= { pcePcepPeerEntry 33 }
pcePcepPeerNumReqSentErrorRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that were rejected by the peer with a
PCErr message.
This might be different than pcePcepPeerNumPCErrRcvd because
not all PCErr messages are used to reject requests, and a
single PCErr message can reject multiple requests."
::= { pcePcepPeerEntry 34 }
pcePcepPeerNumReqSentTimeout OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that have been sent to a peer and
have been abandoned because the peer has taken too long to
respond to them."
::= { pcePcepPeerEntry 35 }
pcePcepPeerNumReqSentCancelSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that were sent to the peer and
explicitly canceled by the local PCEP entity sending a
PCNtf."
::= { pcePcepPeerEntry 36 }
pcePcepPeerNumReqSentClosed OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that were sent to the peer and
implicitly canceled when the session they were sent over was
closed."
::= { pcePcepPeerEntry 37 }
pcePcepPeerNumReqRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests received from this peer. A request
corresponds 1:1 with an RP object in a PCReq message.
This might be greater than pcePcepPeerNumPCReqRcvd because
multiple requests can be batched into a single PCReq
message."
::= { pcePcepPeerEntry 38 }
pcePcepPeerNumSvecRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of SVEC objects received from this peer in PCReq
messages. An SVEC object represents a set of synchronized
requests."
::= { pcePcepPeerEntry 39 }
pcePcepPeerNumSvecReqRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests received from this peer that appeared
in one or more SVEC objects."
::= { pcePcepPeerEntry 40 }
pcePcepPeerNumReqRcvdPendRep OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that have been received from this
peer for which a response is still pending."
::= { pcePcepPeerEntry 41 }
pcePcepPeerNumReqRcvdEroSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that have been received from this
peer for which a response with an ERO object was sent. Such
responses indicate that a path was successfully computed by
the local PCEP entity."
::= { pcePcepPeerEntry 42 }
pcePcepPeerNumReqRcvdNoPathSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that have been received from this
peer for which a response with a NO-PATH object was sent.
Such responses indicate that the local PCEP entity could
not find a path to satisfy the request."
::= { pcePcepPeerEntry 43 }
pcePcepPeerNumReqRcvdCancelSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests received from this peer that were
cancelled by the local PCEP entity sending a PCNtf message.
This might be different than pcePcepPeerNumPCNtfSent because
not all PCNtf messages are used to cancel requests, and a
single PCNtf message can cancel multiple requests."
::= { pcePcepPeerEntry 44 }
pcePcepPeerNumReqRcvdErrorSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests received from this peer that were
rejected by the local PCEP entity sending a PCErr message.
This might be different than pcePcepPeerNumPCErrSent because
not all PCErr messages are used to reject requests, and a
single PCErr message can reject multiple requests."
::= { pcePcepPeerEntry 45 }
pcePcepPeerNumReqRcvdCancelRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that were received from the peer and
explicitly canceled by the peer sending a PCNtf."
::= { pcePcepPeerEntry 46 }
pcePcepPeerNumReqRcvdClosed OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that were received from the peer and
implicitly canceled when the session they were received over
was closed."
::= { pcePcepPeerEntry 47 }
pcePcepPeerNumRepRcvdUnknown OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of responses to unknown requests received from
this peer. A response to an unknown request is a response
whose RP object does not contain the request ID of any
request that is currently outstanding on the session."
::= { pcePcepPeerEntry 48 }
pcePcepPeerNumReqRcvdUnknown OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of unknown requests that have been received from
a peer. An unknown request is a request whose RP object
contains a request ID of zero."
::= { pcePcepPeerEntry 49 }
--
-- The PCEP Sessions Table
--
pcePcepSessTable OBJECT-TYPE
SYNTAX SEQUENCE OF PcePcepSessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of PCEP sessions that involve the local PCEP
entity. Each entry in this table represents a single
session. The entries in this table are read-only.
An entry appears in this table when the corresponding PCEP
session transitions out of idle state. If the PCEP session
transitions back into idle state then the corresponding
entry in this table is removed."
::= { pcePcepObjects 3 }
pcePcepSessEntry OBJECT-TYPE
SYNTAX PcePcepSessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This entry represents a single PCEP session in which the
local PCEP entity participates.
This entry exists only if the corresponding PCEP session has
been initialized by some event, such as manual user
configuration, autodiscovery of a peer, or an incoming TCP
connection."
INDEX { pcePcepEntityIndex,
pcePcepPeerAddrType,
pcePcepPeerAddr,
pcePcepSessInitiator }
::= { pcePcepSessTable 1 }
PcePcepSessEntry ::= SEQUENCE {
pcePcepSessInitiator INTEGER,
pcePcepSessStateLastChange TimeStamp,
pcePcepSessState INTEGER,
pcePcepSessConnectRetry Counter32,
pcePcepSessLocalID Unsigned32,
pcePcepSessRemoteID Unsigned32,
pcePcepSessKeepaliveTimer Unsigned32,
pcePcepSessPeerKeepaliveTimer Unsigned32,
pcePcepSessDeadTimer Unsigned32,
pcePcepSessPeerDeadTimer Unsigned32,
pcePcepSessKAHoldTimeRem Unsigned32,
pcePcepSessOverloaded TruthValue,
pcePcepSessOverloadTime Unsigned32,
pcePcepSessPeerOverloaded TruthValue,
pcePcepSessPeerOverloadTime Unsigned32,
pcePcepSessDiscontinuityTime TimeStamp,
pcePcepSessAvgRspTime Unsigned32,
pcePcepSessLWMRspTime Unsigned32,
pcePcepSessHWMRspTime Unsigned32,
pcePcepSessNumPCReqSent Counter32,
pcePcepSessNumPCReqRcvd Counter32,
pcePcepSessNumPCRepSent Counter32,
pcePcepSessNumPCRepRcvd Counter32,
pcePcepSessNumPCErrSent Counter32,
pcePcepSessNumPCErrRcvd Counter32,
pcePcepSessNumPCNtfSent Counter32,
pcePcepSessNumPCNtfRcvd Counter32,
pcePcepSessNumKeepaliveSent Counter32,
pcePcepSessNumKeepaliveRcvd Counter32,
pcePcepSessNumUnknownRcvd Counter32,
pcePcepSessNumCorruptRcvd Counter32,
pcePcepSessNumReqSent Counter32,
pcePcepSessNumSvecSent Counter32,
pcePcepSessNumSvecReqSent Counter32,
pcePcepSessNumReqSentPendRep Counter32,
pcePcepSessNumReqSentEroRcvd Counter32,
pcePcepSessNumReqSentNoPathRcvd Counter32,
pcePcepSessNumReqSentCancelRcvd Counter32,
pcePcepSessNumReqSentErrorRcvd Counter32,
pcePcepSessNumReqSentTimeout Counter32,
pcePcepSessNumReqSentCancelSent Counter32,
pcePcepSessNumReqRcvd Counter32,
pcePcepSessNumSvecRcvd Counter32,
pcePcepSessNumSvecReqRcvd Counter32,
pcePcepSessNumReqRcvdPendRep Counter32,
pcePcepSessNumReqRcvdEroSent Counter32,
pcePcepSessNumReqRcvdNoPathSent Counter32,
pcePcepSessNumReqRcvdCancelSent Counter32,
pcePcepSessNumReqRcvdErrorSent Counter32,
pcePcepSessNumReqRcvdCancelRcvd Counter32,
pcePcepSessNumRepRcvdUnknown Counter32,
pcePcepSessNumReqRcvdUnknown Counter32
}
pcePcepSessInitiator OBJECT-TYPE
SYNTAX INTEGER {
local(1),
remote(2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The initiator of the session, that is, whether the TCP
connection was initiated by the local PCEP entity or the
peer.
There is a window during session initialization where two
sessions can exist between a pair of PCEP speakers, each
initiated by one of the speakers. One of these sessions is
always discarded before it leaves OpenWait state. However,
before it is discarded, two sessions to the given peer
appear transiently in this MIB module. The sessions are
distinguished by who initiated them, and so this field is an
index for the pcePcepSessTable."
::= { pcePcepSessEntry 1 }
pcePcepSessStateLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time this session entered its
current state as denoted by the pcePcepSessState object."
::= { pcePcepSessEntry 2 }
pcePcepSessState OBJECT-TYPE
SYNTAX INTEGER {
tcpPending(1),
openWait(2),
keepWait(3),
sessionUp(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current state of the session.
The set of possible states excludes the idle state since
entries do not exist in this table in the idle state."
::= { pcePcepSessEntry 3 }
pcePcepSessConnectRetry OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that the local PCEP entity has
attempted to establish a TCP connection for this session
without success. The PCEP entity gives up when this
reaches pcePcepEntityConnectMaxRetry."
::= { pcePcepSessEntry 4 }
pcePcepSessLocalID OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the PCEP session ID used by the local PCEP
entity in the Open message for this session.
If pcePcepSessState is tcpPending then this is the session
ID that will be used in the Open message. Otherwise, this
is the session ID that was sent in the Open message."
::= { pcePcepSessEntry 5 }
pcePcepSessRemoteID OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the PCEP session ID used by the peer in its
Open message for this session.
If pcePcepSessState is tcpPending or openWait then this
field is not used and MUST be set to zero."
::= { pcePcepSessEntry 6 }
pcePcepSessKeepaliveTimer OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The agreed maximum interval at which the local PCEP entity
transmits PCEP messages on this PCEP session. Zero means
that the local PCEP entity never sends Keepalives on this
session.
This field is used if and only if pcePcepSessState is
sessionUp. Otherwise, it is not used and MUST be set to
zero."
::= { pcePcepSessEntry 7 }
pcePcepSessPeerKeepaliveTimer OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The agreed maximum interval at which the peer transmits PCEP
messages on this PCEP session. Zero means that the peer
never sends Keepalives on this session.
This field is used if and only if pcePcepSessState is
sessionUp. Otherwise, it is not used and MUST be set to
zero."
::= { pcePcepSessEntry 8 }
pcePcepSessDeadTimer OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The DeadTimer interval for this PCEP session."
::= { pcePcepSessEntry 9 }
pcePcepSessPeerDeadTimer OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The peer's DeadTimer interval for this PCEP session.
If pcePcepSessState is tcpPending or openWait then this
field is not used and MUST be set to zero."
::= { pcePcepSessEntry 10 }
pcePcepSessKAHoldTimeRem OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The keep alive hold time remaining for this session.
If pcePcepSessState is tcpPending or openWait then this
field is not used and MUST be set to zero."
::= { pcePcepSessEntry 11 }
pcePcepSessOverloaded OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the local PCEP entity has informed the peer that it is
currently overloaded, then this is set to true. Otherwise,
it is set to false."
::= { pcePcepSessEntry 12 }
pcePcepSessOverloadTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The interval of time that is remaining until the local PCEP
entity will cease to be overloaded on this session.
This field is only used if pcePcepSessOverloaded is set to
true. Otherwise, it is not used and MUST be set to zero."
::= { pcePcepSessEntry 13 }
pcePcepSessPeerOverloaded OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the peer has informed the local PCEP entity that it is
currently overloaded, then this is set to true. Otherwise,
it is set to false."
::= { pcePcepSessEntry 14 }
pcePcepSessPeerOverloadTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The interval of time that is remaining until the peer will
cease to be overloaded. If it is not known how long the
peer will stay in overloaded state, this field is set to
zero.
This field is only used if pcePcepSessPeerOverloaded is set
to true. Otherwise, it is not used and MUST be set to
zero."
::= { pcePcepSessEntry 15 }
pcePcepSessDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time that the statistics in
this row were last reset."
::= { pcePcepSessEntry 16 }
pcePcepSessAvgRspTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The average response time for this peer on this session.
If an average response time has not been calculated for this
peer then this object has the value zero."
::= { pcePcepSessEntry 17 }
pcePcepSessLWMRspTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The smallest (low-water mark) response time seen from this
peer on this session.
If no responses have been received from this peer then this
object has the value zero."
::= { pcePcepSessEntry 18 }
pcePcepSessHWMRspTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The greatest (high-water mark) response time seen from this
peer on this session.
If no responses have been received from this peer then this
object has the value zero."
::= { pcePcepSessEntry 19 }
pcePcepSessNumPCReqSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCReq messages sent on this session."
::= { pcePcepSessEntry 20 }
pcePcepSessNumPCReqRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCReq messages received on this session."
::= { pcePcepSessEntry 21 }
pcePcepSessNumPCRepSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCRep messages sent on this session."
::= { pcePcepSessEntry 22 }
pcePcepSessNumPCRepRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCRep messages received on this session."
::= { pcePcepSessEntry 23 }
pcePcepSessNumPCErrSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCErr messages sent on this session."
::= { pcePcepSessEntry 24 }
pcePcepSessNumPCErrRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCErr messages received on this session."
::= { pcePcepSessEntry 25 }
pcePcepSessNumPCNtfSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCNtf messages sent on this session."
::= { pcePcepSessEntry 26 }
pcePcepSessNumPCNtfRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PCNtf messages received on this session."
::= { pcePcepSessEntry 27 }
pcePcepSessNumKeepaliveSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Keepalive messages sent on this session."
::= { pcePcepSessEntry 28 }
pcePcepSessNumKeepaliveRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Keepalive messages received on this session."
::= { pcePcepSessEntry 29 }
pcePcepSessNumUnknownRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of unknown messages received on this session."
::= { pcePcepSessEntry 30 }
pcePcepSessNumCorruptRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of corrupted PCEP message received on this
session."
::= { pcePcepSessEntry 31 }
pcePcepSessNumReqSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests sent on this session. A request
corresponds 1:1 with an RP object in a PCReq message.
This might be greater than pcePcepSessNumPCReqSent because
multiple requests can be batched into a single PCReq
message."
::= { pcePcepSessEntry 32 }
pcePcepSessNumSvecSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of SVEC objects sent on this session in PCReq
messages. An SVEC object represents a set of synchronized
requests."
::= { pcePcepSessEntry 33 }
pcePcepSessNumSvecReqSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests sent on this session that appeared in
one or more SVEC objects."
::= { pcePcepSessEntry 34 }
pcePcepSessNumReqSentPendRep OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that have been sent on this session
for which a response is still pending."
::= { pcePcepSessEntry 35 }
pcePcepSessNumReqSentEroRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of successful responses received on this session.
A response corresponds 1:1 with an RP object in a PCRep
message. A successful response is a response for which an
ERO was successfully computed."
::= { pcePcepSessEntry 36 }
pcePcepSessNumReqSentNoPathRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of unsuccessful responses received on this
session. A response corresponds 1:1 with an RP object in a
PCRep message. An unsuccessful response is a response with
a NO-PATH object."
::= { pcePcepSessEntry 37 }
pcePcepSessNumReqSentCancelRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests sent on this session that were
cancelled by the peer with a PCNtf message.
This might be different than pcePcepSessNumPCNtfRcvd because
not all PCNtf messages are used to cancel requests, and a
single PCNtf message can cancel multiple requests."
::= { pcePcepSessEntry 38 }
pcePcepSessNumReqSentErrorRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests sent on this session that were
rejected by the peer with a PCErr message.
This might be different than pcePcepSessNumPCErrRcvd because
not all PCErr messages are used to reject requests, and a
single PCErr message can reject multiple requests."
::= { pcePcepSessEntry 39 }
pcePcepSessNumReqSentTimeout OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests sent on this session that have been
sent to a peer and have been abandoned because the peer has
taken too long to respond to them."
::= { pcePcepSessEntry 40 }
pcePcepSessNumReqSentCancelSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests sent on this session that were sent
to the peer and explicitly canceled by the local PCEP
entity sending a PCNtf."
::= { pcePcepSessEntry 41 }
pcePcepSessNumReqRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests received on this session. A request
corresponds 1:1 with an RP object in a PCReq message.
This might be greater than pcePcepSessNumPCReqRcvd because
multiple requests can be batched into a single PCReq
message."
::= { pcePcepSessEntry 42 }
pcePcepSessNumSvecRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of SVEC objects received on this session in PCReq
messages. An SVEC object represents a set of synchronized
requests."
::= { pcePcepSessEntry 43 }
pcePcepSessNumSvecReqRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests received on this session that
appeared in one or more SVEC objects."
::= { pcePcepSessEntry 44 }
pcePcepSessNumReqRcvdPendRep OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that have been received on this
session for which a response is still pending."
::= { pcePcepSessEntry 45 }
pcePcepSessNumReqRcvdEroSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of successful responses sent on this session. A
response corresponds 1:1 with an RP object in a PCRep
message. A successful response is a response for which an
ERO was successfully computed."
::= { pcePcepSessEntry 46 }
pcePcepSessNumReqRcvdNoPathSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of unsuccessful responses sent on this session.
A response corresponds 1:1 with an RP object in a PCRep
message. An unsuccessful response is a response with a
NO-PATH object."
::= { pcePcepSessEntry 47 }
pcePcepSessNumReqRcvdCancelSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests received on this session that were
cancelled by the local PCEP entity sending a PCNtf message.
This might be different than pcePcepSessNumPCNtfSent because
not all PCNtf messages are used to cancel requests, and a
single PCNtf message can cancel multiple requests."
::= { pcePcepSessEntry 48 }
pcePcepSessNumReqRcvdErrorSent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests received on this session that were
rejected by the local PCEP entity sending a PCErr message.
This might be different than pcePcepSessNumPCErrSent because
not all PCErr messages are used to reject requests, and a
single PCErr message can reject multiple requests."
::= { pcePcepSessEntry 49 }
pcePcepSessNumReqRcvdCancelRcvd OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of requests that were received on this session
and explicitly canceled by the peer sending a PCNtf."
::= { pcePcepSessEntry 50 }
pcePcepSessNumRepRcvdUnknown OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of responses to unknown requests received on this
session. A response to an unknown request is a response
whose RP object does not contain the request ID of any
request that is currently outstanding on the session."
::= { pcePcepSessEntry 51 }
pcePcepSessNumReqRcvdUnknown OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of unknown requests that have been received on
this session. An unknown request is a request whose RP
object contains a request ID of zero."
::= { pcePcepSessEntry 52 }
---
--- Notifications Configuration
---
pcePcepNotificationsMaxRate OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable indicates the maximum number of
notifications issued per second. If events occur
more rapidly, the implementation may simply fail to
emit these notifications during that period, or may
queue them until an appropriate time. A value of 0
means no notifications are emitted and all should be
discarded (that is, not queued)."
::= { pcePcepObjects 4 }
---
--- Notifications
---
pcePcepSessUp NOTIFICATION-TYPE
OBJECTS {
pcePcepSessState,
pcePcepSessStateLastChange
}
STATUS current
DESCRIPTION
"This notification is sent when the value of
'pcePcepSessState' enters the 'sessionUp' state."
::= { pcePcepNotifications 1 }
pcePcepSessDown NOTIFICATION-TYPE
OBJECTS {
pcePcepSessState,
pcePcepSessStateLastChange
}
STATUS current
DESCRIPTION
"This notification is sent when the value of
'pcePcepSessState' leaves the 'sessionUp' state."
::= { pcePcepNotifications 2 }
pcePcepSessLocalOverload NOTIFICATION-TYPE
OBJECTS {
pcePcepSessOverloaded,
pcePcepSessOverloadTime
}
STATUS current
DESCRIPTION
"This notification is sent when the local PCEP entity enters
overload state for a peer."
::= { pcePcepNotifications 3 }
pcePcepSessLocalOverloadClear NOTIFICATION-TYPE
OBJECTS {
pcePcepSessOverloaded
}
STATUS current
DESCRIPTION
"This notification is sent when the local PCEP entity leaves
overload state for a peer."
::= { pcePcepNotifications 4 }
pcePcepSessPeerOverload NOTIFICATION-TYPE
OBJECTS {
pcePcepSessPeerOverloaded,
pcePcepSessPeerOverloadTime
}
STATUS current
DESCRIPTION
"This notification is sent when a peer enters overload
state."
::= { pcePcepNotifications 5 }
pcePcepSessPeerOverloadClear NOTIFICATION-TYPE
OBJECTS {
pcePcepSessPeerOverloaded
}
STATUS current
DESCRIPTION
"This notification is sent when a peer leaves overload
state."
::= { pcePcepNotifications 6 }
--
-- Module Conformance Statement
--
pcePcepCompliances
OBJECT IDENTIFIER ::= { pcePcepConformance 1 }
pcePcepGroups
OBJECT IDENTIFIER ::= { pcePcepConformance 2 }
--
-- Read-Only Compliance
--
pcePcepModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The Module is implemented with support for read-only. In
other words, only monitoring is available by implementing
this MODULE-COMPLIANCE."
MODULE -- this module
MANDATORY-GROUPS {
pcePcepGeneralGroup,
pcePcepNotificationsGroup
}
OBJECT pcePcepEntityAddrType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION "Only unknown(0), ipv4(1) and ipv6(2) support
is required."
OBJECT pcePcepPeerAddrType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION "Only unknown(0), ipv4(1) and ipv6(2) support
is required."
::= { pcePcepCompliances 1 }
-- units of conformance
pcePcepGeneralGroup OBJECT-GROUP
OBJECTS { pcePcepEntityAdminStatus,
pcePcepEntityOperStatus,
pcePcepEntityAddrType,
pcePcepEntityAddr,
pcePcepEntityConnectTimer,
pcePcepEntityConnectMaxRetry,
pcePcepEntityInitBackoffTimer,
pcePcepEntityMaxBackoffTimer,
pcePcepEntityOpenWaitTimer,
pcePcepEntityKeepWaitTimer,
pcePcepEntityKeepAliveTimer,
pcePcepEntityDeadTimer,
pcePcepEntityAllowNegotiation,
pcePcepEntityMaxKeepAliveTimer,
pcePcepEntityMaxDeadTimer,
pcePcepEntityMinKeepAliveTimer,
pcePcepEntityMinDeadTimer,
pcePcepEntitySyncTimer,
pcePcepEntityRequestTimer,
pcePcepEntityMaxSessions,
pcePcepEntityMaxUnknownReqs,
pcePcepEntityMaxUnknownMsgs,
pcePcepPeerRole,
pcePcepPeerDiscontinuityTime,
pcePcepPeerInitiateSession,
pcePcepPeerSessionExists,
pcePcepPeerNumSessSetupOK,
pcePcepPeerNumSessSetupFail,
pcePcepPeerSessionUpTime,
pcePcepPeerSessionFailTime,
pcePcepPeerSessionFailUpTime,
pcePcepPeerAvgRspTime,
pcePcepPeerLWMRspTime,
pcePcepPeerHWMRspTime,
pcePcepPeerNumPCReqSent,
pcePcepPeerNumPCReqRcvd,
pcePcepPeerNumPCRepSent,
pcePcepPeerNumPCRepRcvd,
pcePcepPeerNumPCErrSent,
pcePcepPeerNumPCErrRcvd,
pcePcepPeerNumPCNtfSent,
pcePcepPeerNumPCNtfRcvd,
pcePcepPeerNumKeepaliveSent,
pcePcepPeerNumKeepaliveRcvd,
pcePcepPeerNumUnknownRcvd,
pcePcepPeerNumCorruptRcvd,
pcePcepPeerNumReqSent,
pcePcepPeerNumSvecSent,
pcePcepPeerNumSvecReqSent,
pcePcepPeerNumReqSentPendRep,
pcePcepPeerNumReqSentEroRcvd,
pcePcepPeerNumReqSentNoPathRcvd,
pcePcepPeerNumReqSentCancelRcvd,
pcePcepPeerNumReqSentErrorRcvd,
pcePcepPeerNumReqSentTimeout,
pcePcepPeerNumReqSentCancelSent,
pcePcepPeerNumReqSentClosed,
pcePcepPeerNumReqRcvd,
pcePcepPeerNumSvecRcvd,
pcePcepPeerNumSvecReqRcvd,
pcePcepPeerNumReqRcvdPendRep,
pcePcepPeerNumReqRcvdEroSent,
pcePcepPeerNumReqRcvdNoPathSent,
pcePcepPeerNumReqRcvdCancelSent,
pcePcepPeerNumReqRcvdErrorSent,
pcePcepPeerNumReqRcvdCancelRcvd,
pcePcepPeerNumReqRcvdClosed,
pcePcepPeerNumRepRcvdUnknown,
pcePcepPeerNumReqRcvdUnknown,
pcePcepSessStateLastChange,
pcePcepSessState,
pcePcepSessConnectRetry,
pcePcepSessLocalID,
pcePcepSessRemoteID,
pcePcepSessKeepaliveTimer,
pcePcepSessPeerKeepaliveTimer,
pcePcepSessDeadTimer,
pcePcepSessPeerDeadTimer,
pcePcepSessKAHoldTimeRem,
pcePcepSessOverloaded,
pcePcepSessOverloadTime,
pcePcepSessPeerOverloaded,
pcePcepSessPeerOverloadTime,
pcePcepSessDiscontinuityTime,
pcePcepSessAvgRspTime,
pcePcepSessLWMRspTime,
pcePcepSessHWMRspTime,
pcePcepSessNumPCReqSent,
pcePcepSessNumPCReqRcvd,
pcePcepSessNumPCRepSent,
pcePcepSessNumPCRepRcvd,
pcePcepSessNumPCErrSent,
pcePcepSessNumPCErrRcvd,
pcePcepSessNumPCNtfSent,
pcePcepSessNumPCNtfRcvd,
pcePcepSessNumKeepaliveSent,
pcePcepSessNumKeepaliveRcvd,
pcePcepSessNumUnknownRcvd,
pcePcepSessNumCorruptRcvd,
pcePcepSessNumReqSent,
pcePcepSessNumSvecSent,
pcePcepSessNumSvecReqSent,
pcePcepSessNumReqSentPendRep,
pcePcepSessNumReqSentEroRcvd,
pcePcepSessNumReqSentNoPathRcvd,
pcePcepSessNumReqSentCancelRcvd,
pcePcepSessNumReqSentErrorRcvd,
pcePcepSessNumReqSentTimeout,
pcePcepSessNumReqSentCancelSent,
pcePcepSessNumReqRcvd,
pcePcepSessNumSvecRcvd,
pcePcepSessNumSvecReqRcvd,
pcePcepSessNumReqRcvdPendRep,
pcePcepSessNumReqRcvdEroSent,
pcePcepSessNumReqRcvdNoPathSent,
pcePcepSessNumReqRcvdCancelSent,
pcePcepSessNumReqRcvdErrorSent,
pcePcepSessNumReqRcvdCancelRcvd,
pcePcepSessNumRepRcvdUnknown,
pcePcepSessNumReqRcvdUnknown,
pcePcepNotificationsMaxRate
}
STATUS current
DESCRIPTION
"Objects that apply to all PCEP MIB module implementations."
::= { pcePcepGroups 1 }
pcePcepNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS { pcePcepSessUp,
pcePcepSessDown,
pcePcepSessLocalOverload,
pcePcepSessLocalOverloadClear,
pcePcepSessPeerOverload,
pcePcepSessPeerOverloadClear
}
STATUS current
DESCRIPTION
"The notifications for a PCEP MIB module implementation."
::= { pcePcepGroups 2 }
END
The pcePcepNotificationsMaxRate object defined in this MIB module has a MAX-ACCESS clause of read-write. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. In particular, pcePcepNotificationsMaxRate may be used improperly to stop notifications being issued, or to permit a flood of notifications to be sent to the management agent at a high rate.
The readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments since, collectively, they provide information about the amount and frequency of path computation requests and responses within the network and can reveal some aspects of its configuration. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP.
SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPsec), there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module.
Implementations SHOULD provide the security features described by the SNMPv3 framework (see [RFC3410]), and implementations claiming compliance to the SNMPv3 standard MUST include full support for authentication and privacy via the User-based Security Model (USM) [RFC3414] with the AES cipher algorithm [RFC3826]. Implementations MAY also provide support for the Transport Security Model (TSM) [RFC5591] in combination with a secure transport such as SSH [RFC5592] or TLS/DTLS [RFC6353].
Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them.
The MIB module in this document uses the following IANA-assigned OBJECT IDENTIFIER values recorded in the SMI Numbers registry:
Descriptor OBJECT IDENTIFIER value
---------- -----------------------
pcePcepMIB { mib-2 XXX }
Editor's Note (to be removed prior to publication): the IANA is requested to assign a value for "XXX" under the 'mib-2' subtree and to record the assignment in the SMI Numbers registry. When the assignment has been made, the RFC Editor is asked to replace "XXX" (here and in the MIB module) with the assigned value and to remove this note.
The authors would like to thank Santanu Mazumder, Meral Shirazipour and Adrian Farrel for their valuable input.
Funding for the RFC Editor function is currently provided by the Internet Society.
| [RFC2119] | Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. |
| [RFC2578] | McCloghrie, K., Perkins, D. and J. Schoenwaelder, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. |
| [RFC2579] | McCloghrie, K., Perkins, D. and J. Schoenwaelder, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. |
| [RFC2580] | McCloghrie, K., Perkins, D. and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. |
| [RFC4001] | Daniele, M., Haberman, B., Routhier, S. and J. Schoenwaelder, "Textual Conventions for Internet Network Addresses", RFC 4001, February 2005. |
| [RFC5440] | Vasseur, JP. and JL. Le Roux, "Path Computation Element (PCE) Communication Protocol (PCEP)", RFC 5440, March 2009. |
Dhruv Dhody
Huawei Technologies
Leela Palace
Bangalore, Karnataka 560008
India
EMail: dhruv.ietf@gmail.com
This example considers the set of PCC / PCE relationships shown in the following figure. The example shows the contents of the PCEP MIB module as read at PCE2 and PCCb.
PCE1---PCE2 PCE3
| / | / |
| / | / |
PCCa/ PCCb PCCc
The IP addresses of the PCE speakers in this diagram are given in the following table.
+------+-------------+
| PCE1 | 1.1.1.1 |
+------+-------------+
| PCE2 | 2.2.2.2 |
+------+-------------+
| PCE3 | 3.3.3.3 |
+------+-------------+
| PCCa | 11.11.11.11 |
+------+-------------+
| PCCb | 22.22.22.22 |
+------+-------------+
| PCCc | 33.33.33.33 |
+------+-------------+
In this example, the PCEP session between PCCb and PCE3 is currently down.
At PCE2, there is a single local PCEP entity which has three peers (PCCa, PCCb and PCE1). There is a session active to all of these peers.
The contents of the PCEP MIB module as read at PCE2 are as follows.
In pcePcepEntityTable {
pcePcepEntityIndex 1,
pcePcepEntityAdminStatus adminStatusUp(1),
pcePcepEntityOperStatus operStatusUp(1),
pcePcepEntityAddrType ipv4(1),
pcePcepEntityAddr 2.2.2.2, -- PCE2
pcePcepEntityConnectTimer 60,
pcePcepEntityConnectMaxRetry 5,
pcePcepEntityInitBackoffTimer 30,
pcePcepEntityMaxBackoffTimer 3600,
pcePcepEntityOpenWaitTimer 60,
pcePcepEntityKeepWaitTimer 60,
pcePcepEntityKeepAliveTimer 1,
pcePcepEntityDeadTimer 4,
pcePcepEntityAllowNegotiation true(1),
pcePcepEntityMaxKeepAliveTimer 60,
pcePcepEntityMaxDeadTimer 240,
pcePcepEntityMinKeepAliveTimer 1,
pcePcepEntityMinDeadTimer 4,
pcePcepEntitySyncTimer 60,
pcePcepEntityRequestTimer 120,
pcePcepEntityMaxSessions 999,
pcePcepEntityMaxUnknownReqs 5,
pcePcepEntityMaxUnknownMsgs 5
}
In pcePcepPeerTable {
pcePcepPeerAddrType ipv4(1), --PCE1
pcePcepPeerAddr 1.1.1.1,
pcePcepPeerRole pccAndPce(3),
pcePcepPeerDiscontinuityTime TimeStamp,
pcePcepPeerInitiateSession true(1),
pcePcepPeerSessionExists true(1),
pcePcepPeerNumSessSetupOK 1,
pcePcepPeerNumSessSetupFail 0,
pcePcepPeerSessionUpTime TimeStamp,
pcePcepPeerSessionFailTime 0,
pcePcepPeerSessionFailUpTime TimeStamp,
pcePcepPeerAvgRspTime 0,
pcePcepPeerLWMRspTime 0,
pcePcepPeerHWMRspTime 0,
pcePcepPeerNumPCReqSent 0,
pcePcepPeerNumPCReqRcvd 0,
pcePcepPeerNumPCRepSent 0,
pcePcepPeerNumPCRepRcvd 0,
pcePcepPeerNumPCErrSent 0,
pcePcepPeerNumPCErrRcvd 0,
pcePcepPeerNumPCNtfSent 0,
pcePcepPeerNumPCNtfRcvd 0,
pcePcepPeerNumKeepaliveSent 123,
pcePcepPeerNumKeepaliveRcvd 123,
pcePcepPeerNumUnknownRcvd 0,
pcePcepPeerNumCorruptRcvd 0,
pcePcepPeerNumReqSent 0,
pcePcepPeerNumSvecSent 0,
pcePcepPeerNumSvecReqSent 0,
pcePcepPeerNumReqSentPendRep 0,
pcePcepPeerNumReqSentEroRcvd 0,
pcePcepPeerNumReqSentNoPathRcvd 0,
pcePcepPeerNumReqSentCancelRcvd 0,
pcePcepPeerNumReqSentErrorRcvd 0,
pcePcepPeerNumReqSentTimeout 0,
pcePcepPeerNumReqSentCancelSent 0,
pcePcepPeerNumReqSentClosed 0,
pcePcepPeerNumReqRcvd 0,
pcePcepPeerNumSvecRcvd 0,
pcePcepPeerNumSvecReqRcvd 0,
pcePcepPeerNumReqRcvdPendRep 0,
pcePcepPeerNumReqRcvdEroSent 0,
pcePcepPeerNumReqRcvdNoPathSent 0,
pcePcepPeerNumReqRcvdCancelSent 0,
pcePcepPeerNumReqRcvdErrorSent 0,
pcePcepPeerNumReqRcvdCancelRcvd 0,
pcePcepPeerNumReqRcvdClosed 0,
pcePcepPeerNumRepRcvdUnknown 0,
pcePcepPeerNumReqRcvdUnknown 0
},
{
pcePcepPeerAddrType ipv4(1), --PCCa
pcePcepPeerAddr 11.11.11.11,
pcePcepPeerRole pcc(1),
pcePcepPeerDiscontinuityTime TimeStamp,
pcePcepPeerInitiateSession false(0),
pcePcepPeerSessionExists true(1),
pcePcepPeerNumSessSetupOK 1,
pcePcepPeerNumSessSetupFail 0,
pcePcepPeerSessionUpTime TimeStamp,
pcePcepPeerSessionFailTime 0,
pcePcepPeerSessionFailUpTime TimeStamp,
pcePcepPeerAvgRspTime 200,
pcePcepPeerLWMRspTime 100,
pcePcepPeerHWMRspTime 300,
pcePcepPeerNumPCReqSent 0,
pcePcepPeerNumPCReqRcvd 3,
pcePcepPeerNumPCRepSent 3,
pcePcepPeerNumPCRepRcvd 0,
pcePcepPeerNumPCErrSent 0,
pcePcepPeerNumPCErrRcvd 0,
pcePcepPeerNumPCNtfSent 0,
pcePcepPeerNumPCNtfRcvd 0,
pcePcepPeerNumKeepaliveSent 123,
pcePcepPeerNumKeepaliveRcvd 123,
pcePcepPeerNumUnknownRcvd 0,
pcePcepPeerNumCorruptRcvd 0,
pcePcepPeerNumReqSent 0,
pcePcepPeerNumSvecSent 0,
pcePcepPeerNumSvecReqSent 0,
pcePcepPeerNumReqSentPendRep 0,
pcePcepPeerNumReqSentEroRcvd 0,
pcePcepPeerNumReqSentNoPathRcvd 0,
pcePcepPeerNumReqSentCancelRcvd 0,
pcePcepPeerNumReqSentErrorRcvd 0,
pcePcepPeerNumReqSentTimeout 0,
pcePcepPeerNumReqSentCancelSent 0,
pcePcepPeerNumReqSentClosed 0,
pcePcepPeerNumReqRcvd 3,
pcePcepPeerNumSvecRcvd 0,
pcePcepPeerNumSvecReqRcvd 0,
pcePcepPeerNumReqRcvdPendRep 0,
pcePcepPeerNumReqRcvdEroSent 3,
pcePcepPeerNumReqRcvdNoPathSent 0,
pcePcepPeerNumReqRcvdCancelSent 0,
pcePcepPeerNumReqRcvdErrorSent 0,
pcePcepPeerNumReqRcvdCancelRcvd 0,
pcePcepPeerNumReqRcvdClosed 0,
pcePcepPeerNumRepRcvdUnknown 0,
pcePcepPeerNumReqRcvdUnknown 0
},
{
pcePcepPeerAddrType ipv4(1), -- PCCb
pcePcepPeerAddr 22.22.22.22,
pcePcepPeerRole pcc(1),
pcePcepPeerDiscontinuityTime TimeStamp,
pcePcepPeerInitiateSession true(1),
pcePcepPeerSessionExists true(1),
pcePcepPeerNumSessSetupOK 1,
pcePcepPeerNumSessSetupFail 0,
pcePcepPeerSessionUpTime TimeStamp,
pcePcepPeerSessionFailTime 0,
pcePcepPeerSessionFailUpTime TimeStamp,
pcePcepPeerAvgRspTime 200,
pcePcepPeerLWMRspTime 100,
pcePcepPeerHWMRspTime 300,
pcePcepPeerNumPCReqSent 0,
pcePcepPeerNumPCReqRcvd 4,
pcePcepPeerNumPCRepSent 4,
pcePcepPeerNumPCRepRcvd 0,
pcePcepPeerNumPCErrSent 0,
pcePcepPeerNumPCErrRcvd 0,
pcePcepPeerNumPCNtfSent 0,
pcePcepPeerNumPCNtfRcvd 0,
pcePcepPeerNumKeepaliveSent 123,
pcePcepPeerNumKeepaliveRcvd 123,
pcePcepPeerNumUnknownRcvd 0,
pcePcepPeerNumCorruptRcvd 0,
pcePcepPeerNumReqSent 0,
pcePcepPeerNumSvecSent 0,
pcePcepPeerNumSvecReqSent 0,
pcePcepPeerNumReqSentPendRep 0,
pcePcepPeerNumReqSentEroRcvd 0,
pcePcepPeerNumReqSentNoPathRcvd 0,
pcePcepPeerNumReqSentCancelRcvd 0,
pcePcepPeerNumReqSentErrorRcvd 0,
pcePcepPeerNumReqSentTimeout 0,
pcePcepPeerNumReqSentCancelSent 0,
pcePcepPeerNumReqSentClosed 0,
pcePcepPeerNumReqRcvd 4,
pcePcepPeerNumSvecRcvd 0,
pcePcepPeerNumSvecReqRcvd 0,
pcePcepPeerNumReqRcvdPendRep 0,
pcePcepPeerNumReqRcvdEroSent 3,
pcePcepPeerNumReqRcvdNoPathSent 1,
pcePcepPeerNumReqRcvdCancelSent 0,
pcePcepPeerNumReqRcvdErrorSent 0,
pcePcepPeerNumReqRcvdCancelRcvd 0,
pcePcepPeerNumReqRcvdClosed 0,
pcePcepPeerNumRepRcvdUnknown 0,
pcePcepPeerNumReqRcvdUnknown 0
}
In pcePcepSessTable {
pcePcepSessInitiator local(1), --PCE1
pcePcepSessStateLastChange TimeStamp,
pcePcepSessState sessionUp(4),
pcePcepSessConnectRetry 0,
pcePcepSessLocalID 1,
pcePcepSessRemoteID 2,
pcePcepSessKeepaliveTimer 1,
pcePcepSessPeerKeepaliveTimer 1,
pcePcepSessDeadTimer 4,
pcePcepSessPeerDeadTimer 4,
pcePcepSessKAHoldTimeRem 1,
pcePcepSessOverloaded false(0),
pcePcepSessOverloadTime 0,
pcePcepSessPeerOverloaded false(0),
pcePcepSessPeerOverloadTime 0,
pcePcepSessDiscontinuityTime TimeStamp,
pcePcepSessAvgRspTime 0,
pcePcepSessLWMRspTime 0,
pcePcepSessHWMRspTime 0,
pcePcepSessNumPCReqSent 0,
pcePcepSessNumPCReqRcvd 0,
pcePcepSessNumPCRepSent 0,
pcePcepSessNumPCRepRcvd 0,
pcePcepSessNumPCErrSent 0,
pcePcepSessNumPCErrRcvd 0,
pcePcepSessNumPCNtfSent 0,
pcePcepSessNumPCNtfRcvd 0,
pcePcepSessNumKeepaliveSent 123,
pcePcepSessNumKeepaliveRcvd 123,
pcePcepSessNumUnknownRcvd 0,
pcePcepSessNumCorruptRcvd 0,
pcePcepSessNumReqSent 0,
pcePcepSessNumSvecSent 0,
pcePcepSessNumSvecReqSent 0,
pcePcepSessNumReqSentPendRep 0,
pcePcepSessNumReqSentEroRcvd 0,
pcePcepSessNumReqSentNoPathRcvd 0,
pcePcepSessNumReqSentCancelRcvd 0,
pcePcepSessNumReqSentErrorRcvd 0,
pcePcepSessNumReqSentTimeout 0,
pcePcepSessNumReqSentCancelSent 0,
pcePcepSessNumReqRcvd 0,
pcePcepSessNumSvecRcvd 0,
pcePcepSessNumSvecReqRcvd 0,
pcePcepSessNumReqRcvdPendRep 0,
pcePcepSessNumReqRcvdEroSent 0,
pcePcepSessNumReqRcvdNoPathSent 0,
pcePcepSessNumReqRcvdCancelSent 0,
pcePcepSessNumReqRcvdErrorSent 0,
pcePcepSessNumReqRcvdCancelRcvd 0,
pcePcepSessNumRepRcvdUnknown 0,
pcePcepSessNumReqRcvdUnknown 0
},
{
pcePcepSessInitiator remote(2), --PCCa
pcePcepSessStateLastChange TimeStamp,
pcePcepSessState sessionUp(4),
pcePcepSessConnectRetry 0,
pcePcepSessLocalID 2,
pcePcepSessRemoteID 1,
pcePcepSessKeepaliveTimer 1,
pcePcepSessPeerKeepaliveTimer 1,
pcePcepSessDeadTimer 4,
pcePcepSessPeerDeadTimer 4,
pcePcepSessKAHoldTimeRem 1,
pcePcepSessOverloaded false(0),
pcePcepSessOverloadTime 0,
pcePcepSessPeerOverloaded false(0),
pcePcepSessPeerOverloadTime 0,
pcePcepSessDiscontinuityTime TimeStamp,
pcePcepSessAvgRspTime 200,
pcePcepSessLWMRspTime 100,
pcePcepSessHWMRspTime 300,
pcePcepSessNumPCReqSent 0,
pcePcepSessNumPCReqRcvd 1,
pcePcepSessNumPCRepSent 1,
pcePcepSessNumPCRepRcvd 0,
pcePcepSessNumPCErrSent 0,
pcePcepSessNumPCErrRcvd 0,
pcePcepSessNumPCNtfSent 0,
pcePcepSessNumPCNtfRcvd 0,
pcePcepSessNumKeepaliveSent 123,
pcePcepSessNumKeepaliveRcvd 123,
pcePcepSessNumUnknownRcvd 0,
pcePcepSessNumCorruptRcvd 0,
pcePcepSessNumReqSent 0,
pcePcepSessNumSvecSent 0,
pcePcepSessNumSvecReqSent 0,
pcePcepSessNumReqSentPendRep 0,
pcePcepSessNumReqSentEroRcvd 0,
pcePcepSessNumReqSentNoPathRcvd 0,
pcePcepSessNumReqSentCancelRcvd 0,
pcePcepSessNumReqSentErrorRcvd 0,
pcePcepSessNumReqSentTimeout 0,
pcePcepSessNumReqSentCancelSent 0,
pcePcepSessNumReqRcvd 3,
pcePcepSessNumSvecRcvd 0,
pcePcepSessNumSvecReqRcvd 0,
pcePcepSessNumReqRcvdPendRep 0,
pcePcepSessNumReqRcvdEroSent 3,
pcePcepSessNumReqRcvdNoPathSent 0,
pcePcepSessNumReqRcvdCancelSent 0,
pcePcepSessNumReqRcvdErrorSent 0,
pcePcepSessNumReqRcvdCancelRcvd 0,
pcePcepSessNumRepRcvdUnknown 0,
pcePcepSessNumReqRcvdUnknown 0
},
{
pcePcepSessInitiator remote(2), --PCCb
pcePcepSessStateLastChange TimeStamp,
pcePcepSessState sessionUp(4),
pcePcepSessConnectRetry 0,
pcePcepSessLocalID 2,
pcePcepSessRemoteID 1,
pcePcepSessKeepaliveTimer 1,
pcePcepSessPeerKeepaliveTimer 1,
pcePcepSessDeadTimer 4,
pcePcepSessPeerDeadTimer 4,
pcePcepSessKAHoldTimeRem 1,
pcePcepSessOverloaded false(0),
pcePcepSessOverloadTime 0,
pcePcepSessPeerOverloaded false(0),
pcePcepSessPeerOverloadTime 0,
pcePcepSessDiscontinuityTime TimeStamp,
pcePcepSessAvgRspTime 200,
pcePcepSessLWMRspTime 100,
pcePcepSessHWMRspTime 300,
pcePcepSessNumPCReqSent 0,
pcePcepSessNumPCReqRcvd 4,
pcePcepSessNumPCRepSent 4,
pcePcepSessNumPCRepRcvd 0,
pcePcepSessNumPCErrSent 0,
pcePcepSessNumPCErrRcvd 0,
pcePcepSessNumPCNtfSent 0,
pcePcepSessNumPCNtfRcvd 0,
pcePcepSessNumKeepaliveSent 123,
pcePcepSessNumKeepaliveRcvd 123,
pcePcepSessNumUnknownRcvd 0,
pcePcepSessNumCorruptRcvd 0,
pcePcepSessNumReqSent 0,
pcePcepSessNumSvecSent 0,
pcePcepSessNumSvecReqSent 0,
pcePcepSessNumReqSentPendRep 0,
pcePcepSessNumReqSentEroRcvd 0,
pcePcepSessNumReqSentNoPathRcvd 0,
pcePcepSessNumReqSentCancelRcvd 0,
pcePcepSessNumReqSentErrorRcvd 0,
pcePcepSessNumReqSentTimeout 0,
pcePcepSessNumReqSentCancelSent 0,
pcePcepSessNumReqRcvd 4,
pcePcepSessNumSvecRcvd 0,
pcePcepSessNumSvecReqRcvd 0,
pcePcepSessNumReqRcvdPendRep 0,
pcePcepSessNumReqRcvdEroSent 3,
pcePcepSessNumReqRcvdNoPathSent 1,
pcePcepSessNumReqRcvdCancelSent 0,
pcePcepSessNumReqRcvdErrorSent 0,
pcePcepSessNumReqRcvdCancelRcvd 0,
pcePcepSessNumRepRcvdUnknown 0,
pcePcepSessNumReqRcvdUnknown 0
}
At PCCb, there is a single local PCEP entity which has two peers (PCE2 and PCE3). There is a session active to PCE2, but the session to PCE3 is currently down.
The contents of the PCEP MIB module as read at PCCb are as follows.
In pcePcepEntityTable {
pcePcepEntityIndex 1,
pcePcepEntityAdminStatus adminStatusUp(1),
pcePcepEntityOperStatus operStatusUp(1),
pcePcepEntityAddrType ipv4(1),
pcePcepEntityAddr 22.22.22.22, -- PCCb
pcePcepEntityConnectTimer 60,
pcePcepEntityConnectMaxRetry 5,
pcePcepEntityInitBackoffTimer 30,
pcePcepEntityMaxBackoffTimer 3600,
pcePcepEntityOpenWaitTimer 60,
pcePcepEntityKeepWaitTimer 60,
pcePcepEntityKeepAliveTimer 1,
pcePcepEntityDeadTimer 4,
pcePcepEntityAllowNegotiation true(1),
pcePcepEntityMaxKeepAliveTimer 60,
pcePcepEntityMaxDeadTimer 240,
pcePcepEntityMinKeepAliveTimer 1,
pcePcepEntityMinDeadTimer 4,
pcePcepEntitySyncTimer 60,
pcePcepEntityRequestTimer 120,
pcePcepEntityMaxSessions 999,
pcePcepEntityMaxUnknownReqs 5,
pcePcepEntityMaxUnknownMsgs 5
}
In pcePcepPeerTable {
pcePcepPeerAddrType ipv4(1), --PCE2
pcePcepPeerAddr 2.2.2.2,
pcePcepPeerRole pce(2),
pcePcepPeerDiscontinuityTime TimeStamp,
pcePcepPeerInitiateSession true(1),
pcePcepPeerSessionExists true(1)),
pcePcepPeerNumSessSetupOK 0,
pcePcepPeerNumSessSetupFail 1,
pcePcepPeerSessionUpTime TimeStamp,
pcePcepPeerSessionFailTime TimeStamp,
pcePcepPeerSessionFailUpTime TimeStamp,
pcePcepPeerAvgRspTime 0,
pcePcepPeerLWMRspTime 0,
pcePcepPeerHWMRspTime 0,
pcePcepPeerNumPCReqSent 4,
pcePcepPeerNumPCReqRcvd 0,
pcePcepPeerNumPCRepSent 0,
pcePcepPeerNumPCRepRcvd 4,
pcePcepPeerNumPCErrSent 0,
pcePcepPeerNumPCErrRcvd 0,
pcePcepPeerNumPCNtfSent 0,
pcePcepPeerNumPCNtfRcvd 0,
pcePcepPeerNumKeepaliveSent 0,
pcePcepPeerNumKeepaliveRcvd 0,
pcePcepPeerNumUnknownRcvd 0,
pcePcepPeerNumCorruptRcvd 0,
pcePcepPeerNumReqSent 4,
pcePcepPeerNumSvecSent 0,
pcePcepPeerNumSvecReqSent 0,
pcePcepPeerNumReqSentPendRep 0,
pcePcepPeerNumReqSentEroRcvd 3,
pcePcepPeerNumReqSentNoPathRcvd 1,
pcePcepPeerNumReqSentCancelRcvd 0,
pcePcepPeerNumReqSentErrorRcvd 0,
pcePcepPeerNumReqSentTimeout 0,
pcePcepPeerNumReqSentCancelSent 0,
pcePcepPeerNumReqSentClosed 0,
pcePcepPeerNumReqRcvd 0,
pcePcepPeerNumSvecRcvd 0,
pcePcepPeerNumSvecReqRcvd 0,
pcePcepPeerNumReqRcvdPendRep 0,
pcePcepPeerNumReqRcvdEroSent 0,
pcePcepPeerNumReqRcvdNoPathSent 0,
pcePcepPeerNumReqRcvdCancelSent 0,
pcePcepPeerNumReqRcvdErrorSent 0,
pcePcepPeerNumReqRcvdCancelRcvd 0,
pcePcepPeerNumReqRcvdClosed 0,
pcePcepPeerNumRepRcvdUnknown 0,
pcePcepPeerNumReqRcvdUnknown 0
},
{
pcePcepPeerAddrType ipv4(1), --PCE3
pcePcepPeerAddr 3.3.3.3,
pcePcepPeerRole pce(2),
pcePcepPeerDiscontinuityTime TimeStamp,
pcePcepPeerInitiateSession true(1),
pcePcepPeerSessionExists false(0),
pcePcepPeerNumSessSetupOK 1,
pcePcepPeerNumSessSetupFail 0,
pcePcepPeerSessionUpTime TimeStamp,
pcePcepPeerSessionFailTime TimeStamp,
pcePcepPeerSessionFailUpTime TimeStamp,
pcePcepPeerAvgRspTime 200,
pcePcepPeerLWMRspTime 100,
pcePcepPeerHWMRspTime 300,
pcePcepPeerNumPCReqSent 4,
pcePcepPeerNumPCReqRcvd 0,
pcePcepPeerNumPCRepSent 0,
pcePcepPeerNumPCRepRcvd 3,
pcePcepPeerNumPCErrSent 0,
pcePcepPeerNumPCErrRcvd 0,
pcePcepPeerNumPCNtfSent 0,
pcePcepPeerNumPCNtfRcvd 0,
pcePcepPeerNumKeepaliveSent 123,
pcePcepPeerNumKeepaliveRcvd 123,
pcePcepPeerNumUnknownRcvd 0,
pcePcepPeerNumCorruptRcvd 0,
pcePcepPeerNumReqSent 4,
pcePcepPeerNumSvecSent 0,
pcePcepPeerNumSvecReqSent 0,
pcePcepPeerNumReqSentPendRep 0,
pcePcepPeerNumReqSentEroRcvd 3,
pcePcepPeerNumReqSentNoPathRcvd 0,
pcePcepPeerNumReqSentCancelRcvd 0,
pcePcepPeerNumReqSentErrorRcvd 0,
pcePcepPeerNumReqSentTimeout 0,
pcePcepPeerNumReqSentCancelSent 0,
pcePcepPeerNumReqSentClosed 1,
pcePcepPeerNumReqRcvd 0,
pcePcepPeerNumSvecRcvd 0,
pcePcepPeerNumSvecReqRcvd 0,
pcePcepPeerNumReqRcvdPendRep 0,
pcePcepPeerNumReqRcvdEroSent 0,
pcePcepPeerNumReqRcvdNoPathSent 0,
pcePcepPeerNumReqRcvdCancelSent 0,
pcePcepPeerNumReqRcvdErrorSent 0,
pcePcepPeerNumReqRcvdCancelRcvd 0,
pcePcepPeerNumReqRcvdClosed 0,
pcePcepPeerNumRepRcvdUnknown 0,
pcePcepPeerNumReqRcvdUnknown 0
}
In pcePcepSessTable {
pcePcepSessInitiator local(1), --PCE2
pcePcepSessStateLastChange TimeStamp,
pcePcepSessState sessionUp(4),
pcePcepSessConnectRetry 0,
pcePcepSessLocalID 1,
pcePcepSessRemoteID 1,
pcePcepSessKeepaliveTimer 1,
pcePcepSessPeerKeepaliveTimer 1,
pcePcepSessDeadTimer 4,
pcePcepSessPeerDeadTimer 4,
pcePcepSessKAHoldTimeRem 1,
pcePcepSessOverloaded false(0),
pcePcepSessOverloadTime 0,
pcePcepSessPeerOverloaded false(0),
pcePcepSessPeerOverloadTime 0,
pcePcepSessDiscontinuityTime TimeStamp,
pcePcepSessAvgRspTime 200,
pcePcepSessLWMRspTime 100,
pcePcepSessHWMRspTime 300,
pcePcepSessNumPCReqSent 4,
pcePcepSessNumPCReqRcvd 0,
pcePcepSessNumPCRepSent 0,
pcePcepSessNumPCRepRcvd 4,
pcePcepSessNumPCErrSent 0,
pcePcepSessNumPCErrRcvd 0,
pcePcepSessNumPCNtfSent 0,
pcePcepSessNumPCNtfRcvd 0,
pcePcepSessNumKeepaliveSent 123,
pcePcepSessNumKeepaliveRcvd 123,
pcePcepSessNumUnknownRcvd 0,
pcePcepSessNumCorruptRcvd 0,
pcePcepSessNumReqSent 4,
pcePcepSessNumSvecSent 0,
pcePcepSessNumSvecReqSent 0,
pcePcepSessNumReqSentPendRep 0,
pcePcepSessNumReqSentEroRcvd 3,
pcePcepSessNumReqSentNoPathRcvd 1,
pcePcepSessNumReqSentCancelRcvd 0,
pcePcepSessNumReqSentErrorRcvd 0,
pcePcepSessNumReqSentTimeout 0,
pcePcepSessNumReqSentCancelSent 0,
pcePcepSessNumReqRcvd 0,
pcePcepSessNumSvecRcvd 0,
pcePcepSessNumSvecReqRcvd 0,
pcePcepSessNumReqRcvdPendRep 0,
pcePcepSessNumReqRcvdEroSent 0,
pcePcepSessNumReqRcvdNoPathSent 0,
pcePcepSessNumReqRcvdCancelSent 0,
pcePcepSessNumReqRcvdErrorSent 0,
pcePcepSessNumReqRcvdCancelRcvd 0,
pcePcepSessNumRepRcvdUnknown 0,
pcePcepSessNumReqRcvdUnknown 0
}
-- no session to PCE3