| Softwire | S. Jiang, Ed. |
| Internet-Draft | Huawei Technologies Co., Ltd |
| Intended status: Standards Track | Y. Fu, Ed. |
| Expires: August 17, 2019 | CNNIC |
| B. Liu | |
| Huawei Technologies Co., Ltd | |
| P. Deacon | |
| IEA Software, Inc. | |
| C. Xie | |
| China Telecom | |
| T. Li | |
| Tsinghua University | |
| M. Boucadair, Ed. | |
| Orange | |
| February 13, 2019 |
RADIUS Attributes for Address plus Port (A+P) based Softwire Mechanisms
draft-ietf-softwire-map-radius-20
IPv4-over-IPv6 transition mechanisms provide IPv4 connectivity services over IPv6 native networks during the IPv4/IPv6 co-existence period. DHCPv6 options have been defined for configuring clients for Lightweight 4over6, Mapping of Address and Port with Encapsulation, and Mapping of Address and Port using Translation unicast softwire mechanisms, and also multicast softwires. However, in many networks, configuration information is stored in an Authentication, Authorization, and Accounting server which utilizes the RADIUS protocol to provide centralized management for users. When a new transition mechanism is developed, new RADIUS attributes need to be defined correspondingly.
This document defines new RADIUS attributes to carry Address plus Port based softwire configuration parameters from an Authentication, Authorization, and Accounting server to a Broadband Network Gateway. Both unicast and multicast attributes are covered.
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 17, 2019.
Copyright (c) 2019 IETF Trust and the persons identified as the document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.
Providers have started deploying and transitioning to IPv6. Several IPv4 service continuity mechanisms based on the Address plus Port (A+P) [RFC6346] have been proposed for providing unicast IPv4 over IPv6-only infrastructure, such as Mapping of Address and Port with Encapsulation (MAP-E) [RFC7597], Mapping of Address and Port using Translation (MAP-T) [RFC7599], and Lightweight 4over6 [RFC7596]. Also, [RFC8114] specifies a generic solution for the delivery of IPv4 multicast services to IPv4 clients over an IPv6 multicast network. For each of these mechanisms, DHCPv6 options have been specified for client configuration.
In many networks, user configuration information is stored in an Authentication, Authorization, and Accounting (AAA) server. AAA servers generally communicate using the Remote Authentication Dial In User Service (RADIUS) [RFC2865] protocol. In a fixed broadband network, a Broadband Network Gateway (BNG) acts as the access gateway for users. That is, the BNG acts as both an AAA client to the AAA server, and a DHCPv6 server for DHCPv6 messages sent by clients. Throughout this document, the term BNG describes a device implementing both the AAA client and DHCPv6 server functions.
Since IPv4-in-IPv6 softwire configuration information is stored in an AAA server, and user configuration information is mainly transmitted through DHCPv6 protocol between the BNGs and Customer Premises Equipment (CEs, a.k.a., CPE), new RADIUS attributes are needed to propagate the information from the AAA servers to BNGs.
The RADIUS attributes defined in this document provide configuration to populate the corresponding DHCPv6 options for unicast and multicast softwire configuration, specifically:
The contents of the attributes defined in this document have a 1:1 mapping into the fields of the various DHCPv6 options in [RFC7598], [RFC8026], and [RFC8115]. Table 1 shows how the DHCPv6 options map to the corresponding RADIUS attribute. For detailed mappings between each DHCPv6 option field and the corresponding RADIUS Attribute or field, see Appendix A.
+----------------------------+--------------------------------+ | DHCPv6 Option | RADIUS Attribute | +----------------------------+--------------------------------+ | OPTION_S46_RULE (89) | Softwire46-Rule | | OPTION_S46_BR (90) | Softwire46-BR | | OPTION_S46_DMR (91) | Softwire46-DMR | | OPTION_S46_V4V6BIND (92) | Softwire46-v4v6Bind | | OPTION_S46_PORTPARAMS (93) | Softwire46-PORTPARAMS | | OPTION_S46_PRIORITY (111) | Softwire46-Priority Attribute | | OPTION_V6_PREFIX64 (113) | Softwire46-Multicast Attribute | +----------------------------+--------------------------------+
Table 1: Mapping between DHCPv6 Options and RADIUS Attributes
A RADIUS attribute for Dual-Stack Lite [RFC6333] is defined in [RFC6519].
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.
The reader should be familiar with the concepts and terms defined in [RFC7596], [RFC7597], [RFC7599], and [RFC8026].
The terms "multicast Basic Bridging BroadBand" element (mB4) and "multicast Address Family Transition Router" element (mAFTR) are defined in [RFC8114].
Softwire46 (S46) is used throughout to denote any of the IPv4-in-IPv6 softwire mechanisms listed above. Additionally, the following abbreviations are used within the document:
This section defines the following attributes:
All of these attributes are allocated from the RADIUS "Extended Type" code space per [RFC6929].
All of these attribute designs follow [RFC6158] and [RFC6929].
This document adheres to [RFC8044] for defining the new attributes.
This attribute is of type "tlv", as defined in the RADIUS Protocol Extensions [RFC6929]. It contains some sub-attributes, with the following requirements:
The Softwire46-Configuration Attribute is structured as follows:
Type
241 (To be confirmed by IANA).
Length
Indicates the total length, in bytes, of all fields of
this attribute, including the Type, Length, Extended-Type,
and the entire length of the embedded attributes.
Extended-Type
TBD1
Value
Contains one or more of the following attributes. Each attribute
type may appear at most once:
Softwire46-MAP-E
For configuring MAP-E clients. For the construction of
this attribute, efer to Section 3.1.1.1.
Softwire46-MAP-T
For configuring MAP-T clients. For the construction of
this attribute, refer to Section 3.1.1.2.
Softwire46-Lightweight-4over6
For configuring Lightweight 4over6 clients. For the
construction of this attribute, refer to Section 3.1.1.3.
The Softwire46-Configuration Attribute is associated with the following identifier: 241.Extended-Type(TBD1).
The Softwire46 attributes can only be encapsulated in the Softwire46-Configuration Attribute. Depending on the deployment scenario, a client might request for more than one transition mechanism at a time. There MUST be at least one Softwire46 attribute encapsulated in one Softwire46-Configuration Attribute. There MUST be at most one instance of each type of Softwire46 attribute encapsulated in one Softwire46-Configuration Attribute.
There are three types of Softwire46 attributes, namely:Section 3.1.3. The hierarchy of the Softwire46 attributes is shown in Figure 1. Section 3.1.2 describes which sub-attributes are mandatory, optional, or not permitted for each defined Softwire46 attribute.
Each type of Softwire46 attribute contains a number of sub-attributes, defined in
/1.Rule-IPv6-Prefix
S / |
o / | 1.Softwire46-Rule -----+ 2.Rule-IPv4-Prefix
f | Softwire46-MAP-E--+ |
t | | 2.Softwire46-BR | 3.EA Length
w | | \
i | | /1.PSID-offset
r | | |
e | | 5.Softwire46-PORTPARAMS -----+ 2.PSID-len
- | \ |
C | | 3.PSID
o | \
n |
f | /1.Rule-IPv6-Prefix
i | / |
g | | 1.Softwire46-Rule------+ 2.Rule-IPv4-Prefix
u | Softwire46-MAP-T--+ |
r | | 3.Softwire46-DMR | 3.EA Length
a | | \
t | | /1.PSID-offset
i | | |
o | | 5.Softwire46-PORTPARAMS------+ 2.PSID-len
n | \ |
| | 3.PSID
A | \
t |
t | /1.IPv4-address
r | / |
i | | 4.Softwire46-v4v6Bind -----+ 2.Bind-IPv6-Prefix
b | Softwire46- | \
u | Lightweight-4over6+ /1.PSID-offset
t \ | |
e | 5.Softwire46-PORTPARAMS ----+ 2.PSID-len
\ |
| 3.PSID
\
Figure 1: Softwire46 Attributes Hierarchy
Softwire46-MAP-E attribute is designed for carrying the configuration information for MAP-E. The structure of Softwire46-MAP-E is shown below:
TLV-Type
1
TLV-Length
Indicates the length of this attribute, including
the TLV-Type, TLV-Length, and TLV-Value fields.
TLV-Value
Contains a set of sub-attributes, with the following requirements:
It MUST contain Softwire46-Rule, defined in Section 3.1.3.1.
It MUST contain Softwire46-BR, defined in Section 3.1.3.2.
It MAY contain Softwire46-PORTPARAMS, defined in Section 3.1.3.5.
Softwire46-MAP-T attribute is designed for carrying the configuration information for MAP-T. The structure of Softwire46-MAP-T is shown below:
TLV-Type
2
TLV-Length
Indicates the length of this attribute, including
the TLV-Type, TLV-Length, and TLV-Value fields.
TLV-Value
Contains a set of sub-attributes, with the following requirements:
It MUST contain Softwire46-Rule, defined in Section 3.1.3.1.
It MUST contain Softwire46-DMR, defined in Section 3.1.3.3.
It MAY contain Softwire46-PORTPARAMS, defined in Section 3.1.3.5.
Softwire46-Lightweight-4over6 attribute is designed for carrying the configuration information for Lightweight 4over6. The structure of Softwire46-Lightweight-4over6 is shown below:
TLV-Type
3
TLV-Length
Indicates the length of this attribute, including
the TLV-Type, TLV-Length, and TLV-Value fields.
TLV-Value
Contains a set of sub-attributes as follows:
It MUST contain Softwire46-BR, defined in Section 3.1.3.2.
It MUST contain Softwire46-V4V6Bind, defined in Section 3.1.3.4.
It MAY contain Softwire46-PORTPARAMS, defined in Section 3.1.3.5.
Table 2 shows which encapsulated sub-attributes are mandatory, optional, or not permitted for each defined Softwire46 attribute.
+-----------------------+-------+-------+--------------------+ | Sub-Attributes | MAP-E | MAP-T | Lightweight 4over6 | +-----------------------+-------+-------+--------------------+ | Softwire46-BR | 1 | 0 | 1 | | Softwire46-Rule | 1 | 1 | 0 | | Softwire46-DMR | 0 | 1 | 0 | | Softwire46-V4V6Bind | 0 | 0 | 1 | | Softwire46-PORTPARAMS | 0-1 | 0-1 | 0-1 | +-----------------------+-------+-------+--------------------+
Table 2: Softwire46 Sub-Attributes
The following table defines the meaning of the above table entries.
0 Not Permitted
0+ Optional, zero or more instances of the attribute
may be present.
0-1 Optional, zero or one instance of the attribute
may be present.
1 Mandatory
Softwire46-Rule can only be encapsulated in Softwire46-MAP-E (Section 3.1.1.1) or Softwire46-MAP-T (Section 3.1.1.2). Depending on the deployment scenario, one Basic Mapping Rule (BMR) and zero or more Forwarding Mapping Rules (FMRs) MUST be included in one Softwire46-MAP-E or Softwire46-MAP-T.
Each type of Softwire46-Rule also contains a number of sub-attributes, including Rule-IPv6-Prefix, Rule-IPv4-Prefix, and EA-Length. The structure of the sub-attributes for Softwire46-Rule is defined in Section 3.1.4.
Defining multiple TLV-types achieves the same design goals as the "Softwire46 Rule Flags" defined in Section 4.1 of [RFC7598]. Using TLV-type set to 4 is equivalent to setting the F-flag in the OPTION_S46_RULE S46 Rule Flags field.
TLV-Type
4 Basic Mapping Rule only (not to be used for forwarding)
5 Forwarding Permitted Mapping Rule (may be used for
forwarding. Can also be a Basic Mapping Rule)
TLV-Length
Indicates the length of this attribute, including
the TLV-Type, TLV-Length, and TLV-Value fields.
Data Type
The attribute Softwire46-Rule is of type tlv (Section 3.13 of
[RFC8044]).
TLV-Value
This field contains a set of attributes as follows:
Rule-IPv6-Prefix
This attribute contains the IPv6 prefix for use in the MAP rule.
Refer to Section 3.1.4.1.
Rule-IPv4-Prefix
This attribute contains the IPv4 prefix for use in the MAP rule.
Refer to Section 3.1.4.2.
EA-Length
This attribute contains the Embedded-Address (EA) bit length.
Refer to Section 3.1.4.1.
Softwire46-BR can only be encapsulated in Softwire46-MAP-E (Section 3.1.1.1) or Softwire46-Lightweight-4over6 (Section 3.1.1.3).
There MUST be at least one Softwire46-BR included in each Softwire46-MAP-E or Softwire46-Lightweight-4over6.
The structure of Softwire46-BR is shown below:
TLV-Type
6
TLV-Length
18 octets
Data Type
The attribute Softwire46-BR is of type ip6addr (Section 3.9 of
[RFC8044]).
TLV-Value
br-ipv6-address. A fixed-length field of 16 octets that
specifies the IPv6 address for the Softwire46 Border Relay (BR).
Softwire46-DMR may only appear in Softwire46-MAP-T (Section 3.1.1.2). There MUST be exactly one Softwire46-DMR included in one Softwire46-MAP-T.
The structure of Softwire46-DMR is shown below:
TLV-Type
7
TLV-Length
4 + length of dmr-ipv6-prefix specified in octets.
Data Type
The attribute Softwire46-DMR is of type ip6pref (Section 3.10 of
[RFC8044]).
TLV-Value
dmr-ipv6-prefix. A variable-length field specifying the IPv6
prefix for the BR. This field is right-padded with zeros to
the nearest octet boundary when dmr-prefix6-len is not
divisible by 8. Prefixes with from 0 to 96 are allowed.
Softwire46-V4V6Bind may only be encapsulated in Softwire46-Lightweight-4over6 (Section 3.1.1.3). There MUST be exactly one Softwire46-V4V6Bind included in each Softwire46-Lightweight-4over6.
The structure of Softwire46-V4V6Bind is shown below:
TLV-Type
8
TLV-Length
Indicates the length of this attribute, including
the TLV-Type, TLV-Length, and TLV-Value fields.
Data Type
The attribute Softwire46-V4V6Bind is of type tlv (Section 3.13 of
[RFC8044]).
TLV-Value
This field contains a set of attributes as follows:
IPv4-address
This attribute contains an IPv4 address, used to specify
the full or shared IPv4 address of the CE. Refer to
Section 3.1.5.1.
Bind-IPv6-Prefix
This attribute contains an IPv6 prefix used to indicate which
configured prefix the Softwire46 CE should use for constructing
the softwire. Refer to Section 3.1.5.2.
Softwire46-PORTPARAMS is optional. It is used to specify port set information for IPv4 address sharing between clients. Softwire46-PORTPARAMS MAY be included in any of the Softwire46 attributes.
The structure of Softwire46-PORTPARAMS is shown below:
TLV-Type
9
TLV-Length
Indicates the length of this attribute, including
the TLV-Type, TLV-Length, and TLV-Value fields.
Data Type
The attribute Softwire46-PORTPARAMS is of type tlv (Section 3.13
of [RFC8044]).
TLV-Value
This field contains a set of attributes as follows:
PSID-offset
This attribute specifies the numeric value for the Softwire46
algorithm's excluded port range/offset bits (a bits). Refer to
Section 3.1.6.1.
PSID-len
This attribute specifies the number of significant bits in the
PSID field (also known as 'k'). Refer to Section 3.1.6.2.
PSID
This attribute specifies PSID value. Refer to Section 3.1.6.3.
There are two types of Softwire46-Rule: the Basic Mapping Rule and the Forwarding Mapping Rule, indicated by the value in the TLV-Type field of Softwire46-Rule (see Section 3.1.3.1).
Each type of Softwire46-Rule also contains a number of Sub-attributes as detailed in the following sub-sections.
Rule-IPv6-Prefix is REQUIRED for every Softwire46-Rule. There MUST be exactly one Rule-IPv6-Prefix encapsulated in each type of Softwire46-Rule.
Rule-IPv6-Prefix follows the framed IPv6 prefix designed in [RFC3162] and [RFC8044].
The structure of Rule-IPv6-Prefix is shown below:
TLV-Type
10
TLV-Length
20 octets
Data Type
The attribute Rule-IPv6-Prefix is of type ipv6pref (Section 3.10
of [RFC8044]).
TLV-Value
rule-ipv6-prefix. 128-bits long field that specifies an IPv6
prefix appearing in the MAP rule.
This attribute is used to convey the MAP Rule IPv4 prefix. The structure of Rule-IPv4-Prefix is shown below:
TLV-Type
11
TLV-Length
8 octets
Data Type
The attribute Rule-IPv4-Prefix is of type ipv4pref (Section 3.11
of [RFC8044]).
TLV-Value
rule-ipv4-prefix. 32-bits long. Specifies the IPv4 prefix
appearing in the MAP rule.
This attribute is used to convey the Embedded-Address(EA) bit length. The structure of EA-Length is shown below:
TLV-Type
12
TLV-Length
6 octets
Data Type
The attribute EA-Length is of type integer (Section 3.1 of
[RFC8044]).
TLV-Value
EA-len; 32-bits long. Specifies the Embedded-Address(EA) bit
length. Allowed values range from 0 to 48.
The IPv4-address MAY be used to specify the full or shared IPv4 address of the CE.
The structure of IPv4-address is shown below:
TLV-Type
13
TLV-Length
6 octets
Data Type
The attribute IPv4-address is of type ipv4addr (Section 3.8
of [RFC8044]).
TLV-Value
32-bits long. Specifies the IPv4 address to appear in
Softwire46-V4V6Bind (Section 3.1.3.4).
The Bind-IPv6-Prefix is used by the CE to identify the correct IPv6 prefix to be used as the tunnel source.
The structure of Bind-IPv6-Prefix is shown below:
TLV-Type
14
TLV-Length
4 + length of bind-ipv6-prefix specified in octets.
Data Type
The attribute Bind-IPv6-Prefix is of type ipv6pref (Section 3.10
of [RFC8044]).
TLV-Value
bind-ipv6-prefix. A variable-length field specifying the IPv6
prefix or address for the Softwire46 CE. This field is
right-padded with zeros to the nearest octet boundary
when bindprefix6-len is not divisible by 8.
This attribute is used to convey the Port Set Identifier offset as defined in [RFC7597]. This attribute is encoded 32 bits as per the recommendation in Appendix A.2.1 of [RFC6158].
The structure of PSID-offset is shown below:
TLV-Type
15
TLV-Length
6 octets
Data Type
The attribute PSID-offset is of type integer (Section 3.1
of [RFC8044]).
TLV-Value
Contains the PSID-Offset (8-bits) right
justified, and the unused bits in this field MUST
be set to zero. This field that specifies the
numeric value for the Softwire46 algorithm's excluded
port range/offset bits (a bits), as per Section 5.1
of RFC7597. Allowed values are between 0 and 15.
Default values for this field are specific to the
Softwire mechanism being implemented and are defined
in the relevant specification document.
This attribute is used to convey the PSID length as defined in [RFC7597]. This attribute is encoded 32 bits as per the recommendation in Appendix A.2.1 of [RFC6158].
The structure of PSID-len is shown below:
TLV-Type
16
TLV-Length
6 octets
Data Type
The attribute PSID-len is of type integer (Section 3.1
of [RFC8044]).
TLV-Value
Contains the PSID-len (8-bits) right
justified, and the unused bits in this field MUST
be set to zero. This field specifies the number of
significant bits in the PSID field (also known as
'k'). When set to 0, the PSID field is to be ignored.
After the first 'a' bits, there are k bits in the
port number representing the value of the PSID.
Subsequently, the address sharing ratio would be
2^k.
This attribute is used to convey the PSID as defined in [RFC7597]. This attribute is encoded 32 bits as per the recommendation in Appendix A.2.1 of [RFC6158].
The structure of PSID is shown below:
TLV-Type
17
TLV-Length
6 octets
Data Type
The attribute Bind-IPv6-Prefix is of type integer (Section 3.1
of [RFC8044]).
TLV-Value
Contains the PSID (16-bits) right justified, and the unused bits
in this field MUST be set to zero.
The PSID value algorithmically identifies a set of ports
assigned to a CE. The first k bits on the left of this
2-octet field is the PSID value. The remaining (16-k) bits
on the right are padding zeros.
The Softwire46-Priority Attribute defines a 32-bit Softwire46-option-code field to contain the information allowing the client to prioritize which mechanism to use, corresponding to OPTION_S46_PRIORITY defined in [RFC8026]. The following requirements apply:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type | ... .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. Softwire46-option-code |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Softwire46-option-code |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
241 (To be confirmed by IANA)
Length
Indicates the length of this attribute,
including the Type, Length, Extended-Type and Value fields.
Extended-Type
TBD5
Softwire46-option-code
Integer. A 32-bit IANA-registered option code representing
an Softwire46 mechanism. The option codes and their
corresponding Softwire46 mechanisms are listed in Section 7.3.
Softwire46 mechanisms are prioritized in the appearance order
of the Softwire46-option-code(s) in the Softwire46-Priority
Attribute.
A Softwire46-Priority Attribute MUST contain at least one
Softwire46-option-code.
The Softwrie46-Priority Attribute is structured as follows:
The Softwire46-Priority Attribute is associated with the following identifier: 241.Extended-Type (TBD5).
The Softwire46-Multicast Attribute conveys the IPv6 prefixes to be used to synthesize multicast and unicast IPv4-embedded IPv6 addresses as per [RFC8114]. This attribute is of type "tlv" and contains additional TLVs. The following requirements apply:
The Softwire46-Multicast Attribute is structured as follows:
Type
241 (To be confirmed by IANA)
Length
This field indicates the total length in bytes of all fields of
this attribute, including the Type, Length, Extended-Type, and the
entire length of the embedded attributes.
Extended-Type
TBD6
Value
This field contains a set of attributes as follows:
ASM-Prefix64
This attribute contains the ASM IPv6 prefix. Refer to
Section 3.3.1.
SSM-Prefix64
This attribute contains the SSM IPv6 prefix. Refer to
Section 3.3.2.
U-Prefix64
This attribute contains the IPv4 prefix used for address
translation. Refer to Section 3.3.3.
The Softwire46-Multicast Attribute is associated with the following identifier: 241.Extended-Type(TBD6).
The ASM-Prefix64 attribute is structured as follows:
TLV-Type
18
TLV-Length
16 octets. The length of ssm-prefix64 must be to 96 [RFC8115].
Data Type
The attribute ASM-Prefix64 is of type ipv6prefix (Section 3.10 of
[RFC8044]).
TLV-Value
This field specifies the IPv6 multicast prefix (asm-prefix64)
to be used to synthesize the IPv4-embedded IPv6 addresses of the
multicast groups in the ASM mode. The conveyed multicast IPv6
prefix MUST belong to the ASM range.
The SSM-Prefix64 attribute is structured as follows:
Type
19
TLV-Length
16 octets. The length of ssm-prefix64 must be to 96 [RFC8115].
Data Type
The attribute SSM-Prefix64 is of type ipv6prefix (Section 3.10 of
[RFC8044]).
TLV-Type
This field specifies the IPv6 multicast prefix (ssm-prefix64)
to be used to synthesize the IPv4-embedded IPv6 addresses of the
multicast groups in the SSM mode. The conveyed multicast IPv6
prefix MUST belong to the SSM range.
The structure of U-Prefix64 is shown below:
TLV-Type
20
TLV-Length
4 + length of unicast-prefix. As specified in [RFC6052],
the unicast-prefix prefix-length MUST be set to 32, 40, 48,
56, 64, or 96.
Data Type
The attribute U-Prefix64 is of type ipv6prefix (Section 3.10 of
[RFC8044]).
TLV-Value
This field identifies the IPv6 unicast prefix to
be used in SSM mode for constructing the IPv4-embedded IPv6
addresses representing the IPv4 multicast sources in the IPv6
domain. It may also be used to extract the IPv4 address from the
received multicast data flows.
Figure 2 illustrates how the RADIUS and DHCPv6 protocols interwork to provide CE with softwire configuration information.
CE BNG AAA Server
| | |
|-------1.DHCPv6 Solicit------->| |
|(ORO with unicast and/or m'cast| |
| container option code(s)) | |
| | |
| |-------2.Access-Request------->|
| | (Softwire46-Configuration |
| | Attribute and/or |
| |Softwire46-Multicast Attribute)|
| | |
| |<------3.Access-Accept---------|
| | (Softwire46-Configuration |
| | Attribute and/or |
| |Softwire46-Multicast Attribute)|
| | |
|<----4.DHCPv6 Advertisement----| |
| (container option(s)) | |
| | |
|-------5.DHCPv6 Request------>| |
| (container Option(s)) | |
| | |
|<--------6.DHCPv6 Reply--------| |
| (container option(s)) | |
| | |
DHCPv6 RADIUS
Figure 2: Interaction between DHCPv6 and AAA Server with RADIUS authentication
The authorization operation could also be done independently, after the authentication process. In this case, steps 1-5 are completed as above, then the following steps are performed:
In addition to the above, the following points need to be considered:
In some deployments, the DHCP server may use the Accounting-Request to report to a AAA server the softwire configuration returned to a requesting host. It is the responsibility of the DHCP server to ensure the consistency of the configuration provided to requesting hosts. Reported data to a AAA server may be required for various operational purposes (e.g., regulatory).
This document specifies three new RADIUS attributes, and their formats are as follows:
The following table describes which attributes may be found, in which kinds of packets and in what quantity.
Request Accept Reject Challenge Accounting # Attribute
Request
0-1 0-1 0 0 0-1 241.TBD1 Softwire46-
Configuration
0-1 0-1 0 0 0-1 241.TBD5 Softwire46-
Priority
0-1 0-1 0 0 0-1 241.TBD6 Softwire46-
Multicast
Known security vulnerabilities of the RADIUS protocol are discussed in [RFC2607], [RFC2865], and[RFC2869]. Use of IPsec [RFC4301] for providing security when RADIUS is carried in IPv6 is discussed in [RFC3162].
Specific security considerations for interactions between the MAP CE and the BNG are discussed in [RFC7597] and [RFC7599]. Security considerations for Lightweight 4over6 are discussed in [RFC7596]. Security considerations for DHCPv6-Based Softwire46 Prioritization Mechanism are discussed in [RFC8026]. Security considerations for multicast scenarios are discussed in [RFC8114]. Furthermore, generic DHCPv6 security mechanisms can be applied to DHCPv6 intercommunication between the CE and the BNG.
IANA is requested to make new code point assignments for RADIUS attributes as described in the following subsections.
This document requests IANA to assign the Attribute Types defined in this document from the RADIUS namespace as described in the "IANA Considerations" section of [RFC3575], in accordance with BCP 26 [RFC8126].
This document requests that IANA register three new RADIUS attributes, from the "Short Extended Space" of [RFC6929]. The attributes are: Softwire46-Configuration Attribute, Softwire46-Priority Attribute, and Softwire46-Multicast Attribute:
Type Description Data Type Reference ---- ----------- --------- --------- 241.TBD1 Softwire46-Configuration tlv Section 3.1 241.TBD5 Softwire46-Priority integer Section 3.2 241.TBD6 Softwire46-Multicast tlv Section 3.3
IANA is requested to create a new registry called "RADIUS Softwire46 Configuration and Multicast Attributes".
All attributes in this registry have one or more parent RADIUS attributes in nesting (refer to [RFC6929]).
This registry must be initially populated with the following values:
Value Description Data Type Reference ----- ----------- --------- --------- 0 Reserved 1 Softwire46-MAP-E tlv Section 3.1.1.1 2 Softwire46-MAP-T tlv Section 3.1.1.2 3 Softwire46-Lightweight-4over6 tlv Section 3.1.1.3 4 Softwire46-Rule tlv Section 3.1.3.1 5 Softwire46-Rule tlv Section 3.1.3.1 6 Softwire46-BR ipv6addr Section 3.1.3.2 7 Softwire46-DMR ipv6prefix Section 3.1.3.3 8 Softwire46-V4V6Bind tlv Section 3.1.3.4 9 Softwire46-PORTPARAMS tlv Section 3.1.3.5 10 Rule-IPv6-Prefix ipv6prefix Section 3.1.4.1 11 Rule-IPv4-Prefix ipv4prefix Section 3.1.4.2 12 EA-Length integer Section 3.1.4.3 13 IPv4-address ipv4addr Section 3.1.5.1 14 Bind-IPv6-Prefix ipv6prefix Section 3.1.5.2 15 PSID-offset integer Section 3.1.6.1 16 PSID-len integer Section 3.1.6.2 17 PSID integer Section 3.1.6.3 18 ASM-Prefix64 ipv6prefix Section 3.3.1 19 SSM-Prefix64 ipv6prefix Section 3.3.2 20 U-Prefix64 ipv6prefix Section 3.3.3 21-255 Unassigned
The registration procedure for this registry is Standards Action as defined in [RFC8126].
The Softwire46-Priority Attribute defines a 16-bit Softwire46-option-code field, for which IANA is requested to create and maintain a new registry entitled "Option Codes Permitted in the Softwire46-Priority Attribute". The registration procedure for this registry is Standards Action as defined in [RFC8126].
This document requests IANA to register the three option codes of the Softwire46 mechanisms permitted to be included in the Softwire46-Priority Attribute. The value of option code corresponds to the TLV-Type defined in Section 3.1.1. Additional options may be added to this list in the future using the IETF Review process described in Section 4.8 of [RFC8126].
Table 3 shows the option codes required, and the Softwire46 mechanisms that they represent. The option code for DS-Lite is derived from the IANA allocated RADIUS Attribute Type value for DS-Lite [RFC6519]. The option codes for MAP-E, MAP-T, and Lightweight 4over6 need to be assigned. The option codes for MAP-E, MAP-T, and Lightweight 4over6 should also be used as the TLV-Type values for the MAP-E, MAP-T, and Lightweight 4over6 attributes defined in Section 3.1.1.
+-----------+--------------------+-----------+
|Option Code|Softwire46 Mechanism| Reference |
+-----------+--------------------+-----------+
| TBD2 | MAP-E | RFC7597 |
| TBD3 | MAP-T | RFC7599 |
| TBD4 | Lightweight 4over6 | RFC7596 |
| 144 | DS-Lite | RFC6519 |
+--------------------------------+-----------+
Table 3: Option Codes to S46 Mechanisms
Qiong Sun
China Telecom
Beijing China
Email: sunqiong@ctbri.com.cn
Qi Sun
Tsinghua University
Department of Computer Science, Tsinghua University
Beijing 100084
P.R.China
Phone: +86-10-6278-5822
Email: sunqibupt@gmail.com
Cathy Zhou
Huawei Technologies
Bantian, Longgang District
Shenzhen 518129
Email: cathy.zhou@huawei.com
Tina Tsou
Huawei Technologies(USA)
2330 Central Expressway
Santa Clara, CA 95050
USA
Email: Tina.Tsou.Zouting@huawei.com
ZiLong Liu
Tsinghua University
Beijing 100084
P.R.China
Phone: +86-10-6278-5822
Email: liuzilong8266@126.com
Yong Cui
Tsinghua University
Beijing 100084
P.R.China
Phone: +86-10-62603059
Email: yong@csnet1.cs.tsinghua.edu.cn
The authors would like to thank the valuable comments made by Peter Lothberg, Wojciech Dec, Ian Farrer, Suresh Krishnan, Qian Wang, Wei Meng, Cui Wang, Alan Dekok, Stefan Winter, and Yu Tianpeng to this document.
This document was merged with draft-sun-softwire-lw4over6-radext-01 and draft-wang-radext-multicast-radius-ext-00, thanks to everyone who contributed to this document.
This document was produced using the xml2rfc tool [RFC7991].
The following sections detail the mappings between the softwire DHCPv6 option fields and the relevant RADIUS attributes as defined in this document.
| OPTION_S46_RULE Field | Softwire46-Rule Name | TLV Field |
|---|---|---|
| flags | N/A | TLV-type (TBD7, TBD8) |
| ea-len | EA-Length | EA-len |
| prefix4-len | Rule-IPv4-Prefix | ruleprefix4-len |
| ipv4-prefix | Rule-IPv4-Prefix | rule-ipv4-prefix |
| prefix6-len | Rule-IPv6-Prefix | ruleprefix6-len |
| ipv6-prefix | Rule-IPv6-Prefix | rule-ipv6-prefix |
| OPTION_S46_BR Field | Softwire46-BR Field |
|---|---|
| br-ipv6-address | br-ipv6-address |
| OPTION_S46_BR Field | Softwire46-DMR Field |
|---|---|
| dmr-prefix6-len | dmr-prefix6-len |
| dmr-ipv6-prefix | dmr-ipv6-prefix |
| OPTION_S46_V4V6BIND Field | Softwire46-V4V6Bind Name | TLV Field |
|---|---|---|
| ipv4-address | IPv4-address | ipv4-address |
| bindprefix6-len | Bind-IPv6-Prefix | bind6prefix-len |
| bind-ipv6-prefix | Bind-IPv6-Prefix | bind-ipv6-prefix |
| OPTION_S46_PORTPARAMS Field | Softwire46-PORTPARAMS Name | TLV Field |
|---|---|---|
| offset | PSID-offset | PSID-Offset |
| PSID-len | PSID-len | PSID-len |
| PSID | PSID | PSID |
| OPTION_S46_PRIORITY Field | Softwire46-Priority Attribute Field |
|---|---|
| s46-option-code | Softwire46-option-code |
| OPTION_V6_PREFIX64 Field | Softwire46-Multicast Attribute TLV Name | TLV Field |
|---|---|---|
| asm-length | ASM-Prefix64 | Prefix-Length |
| ASM_mPrefix64 | ASM-Prefix64 | ASM Prefix64 |
| ssm-length | SSM-Prefix64 | Prefix-Length |
| SSM_mPrefix64 | SSM-Prefix64 | SSM Prefix64 |
| unicast-length | U-Prefix64 | Prefix-Length |
| uPrefix64 | U-Prefix64 | Unicast Prefix64 |