Datagram Transport Layer Security (DTLS) Transport Mapping for Syslog
draft-ietf-syslog-dtls-02.txt

Abstract

This document describes the transport of syslog messages over DTLS (Datagram Transport Level Security). It provides a secure transport for syslog messages in cases where a connection-less transport is desired.

Status of this Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as “work in progress.”

This Internet-Draft will expire on November 1, 2010.

Copyright Notice

Copyright (c) 2010 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.

This document may contain material from IETF Documents or IETF Contributions published or made publicly available before November 10, 2008. The person(s) controlling the copyright in some of this material may not have granted the IETF Trust the right to allow modifications of such material outside the IETF Standards Process. Without obtaining an adequate license from the person(s) controlling the copyright in such materials, this document may not be modified outside the IETF Standards Process, and derivative works of it may not be created outside the IETF Standards Process, except to format it for publication as an RFC or to translate it into languages other than English.

Table of Contents

1.  Introduction

2.  Terminology

3.  Security Requirements for Syslog

4.  Using DTLS to Secure Syslog

5.  Protocol Elements
    5.1.  Transport
    5.2.  Port Assignment
    5.3.  Initiation
        5.3.1.  Certificate-Based Authentication
    5.4.  Sending data
        5.4.1.  Message Size
    5.5.  Closure

6.  Security Policies

7.  IANA Consideration

8.  Security Considerations

9.  Acknowledgements

10.  References
    10.1.  Normative References
    10.2.  Informative References

§  Authors' Addresses

1.  Introduction

The syslog protocol [RFC5424] (Gerhards, R., “The Syslog Protocol,” March 2009.) is designed to run over different transports for different environments. Syslog over TLS [RFC5425] (Miao, F., Ma, Y., and J. Salowey, “Transport Layer Security (TLS) Transport Mapping for Syslog,” March 2009.) provides a combination of TCP transport reliability with TLS security [RFC5246] (Dierks, T. and E. Rescorla, “The Transport Layer Security (TLS) Protocol Version 1.2,” August 2008.) and is the RECOMMENDED transport. In some circumstances, an operator might prefer using UDP to TCP as the transport. Transmission of syslog Messages over UDP [RFC5426] (Okmianski, A., “Transmission of Syslog Messages over UDP,” March 2009.) defines how to provide unreliable, non-secure datagram transport for syslog. This transport is NOT RECOMMENDED.

The datagram transport layer security protocol (DTLS) [RFC4347] (Rescorla, E. and N. Modadugu, “Datagram Transport Layer Security,” April 2006.) is designed to meet the requirements of applications that need secure datagram transport by combining UDP transport with TLS security. DTLS has been mapped onto different transports (i.e. UDP [RFC0768] (Postel, J., “User Datagram Protocol,” August 1980.) and DCCP [RFC4340] (Kohler, E., Handley, M., and S. Floyd, “Datagram Congestion Control Protocol (DCCP),” March 2006.) ). Syslog over DTLS is another transport mapping that may be used to secure syslog in deployments where the operators feel that this best meets their requirements.

As the Internet best runs on the basis of appropriate resource sharing, both syslog over DTLS over DCCP [RFC5238] (Phelan, T., “Datagram Transport Layer Security (DTLS) over the Datagram Congestion Control Protocol (DCCP),” May 2008.) and syslog over DTLS over UDP are defined in this specification. If an operator has the choice of the two, it is recommended to use syslog over DTLS over DCCP.

2.  Terminology

The following definitions from [RFC5424] (Gerhards, R., “The Syslog Protocol,” March 2009.) are used in this document:

• An "originator" generates syslog content to be carried in a message.
• A "collector" gathers syslog content for further analysis.
• A "relay" forwards messages, accepting messages from originators or other relays, and sending them to collectors or other relays.
• A "transport sender" passes syslog messages to a specific transport protocol.
• A "transport receiver" takes syslog messages from a specific transport protocol.

This document adds the following definitions:

• A "DTLS client" is an application that can initiate a DTLS Client Hello to a server.
• A "DTLS server" is an application that can receive a Client Hello from a client and reply with a Server Hello.

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119] (Bradner, S., “Key words for use in RFCs to Indicate Requirement Levels,” March 1997.).

3.  Security Requirements for Syslog

The security requirements for the transport of syslog messages are discussed in Section 2 of [RFC5425] (Miao, F., Ma, Y., and J. Salowey, “Transport Layer Security (TLS) Transport Mapping for Syslog,” March 2009.). These also apply to this specification.

The following secondary threat is also considered in this document:

• Denial of Service. Denial of service is discussed in [RFC5424] (Gerhards, R., “The Syslog Protocol,” March 2009.), which states that an attacker may send more messages to a transport receiver than the transport receiver could handle. When using a secure transport protocol handshake, an attacker may use a spoofed IP source to engage the server in a cryptographic handshake to deliberately consume the server's resources.

4.  Using DTLS to Secure Syslog

DTLS can be used as a secure transport to counter all the primary threats to syslog described in [RFC5425] (Miao, F., Ma, Y., and J. Salowey, “Transport Layer Security (TLS) Transport Mapping for Syslog,” March 2009.):

• Confidentiality to counter disclosure of the message contents.
• Integrity checking to counter modifications to a message on a hop- by-hop basis.
• Server or mutual authentication to counter masquerade.

In addition DTLS also provides:

• A cookie exchange mechanism during handshake to counter Denial of Service attacks
• A sequence number in the header to counter replay attacks.

Note: This secure transport (i.e., DTLS) only secures syslog transport in a hop-by-hop manner, and is not concerned with the contents of syslog messages. In particular, the authenticated identity of the transport sender (e.g., subject name in the certificate) is not necessarily related to the HOSTNAME field of the syslog message. When authentication of syslog message origin is required, [I‑D.ietf‑syslog‑sign] (Kelsey, J., Callas, J., and A. Clemm, “Signed syslog Messages,” December 2009.) can be used.

5.  Protocol Elements

5.1.  Transport

DTLS can run over multiple transports. Implementations of this specification MUST support DTLS over UDP and SHOULD support DTLS over DCCP [RFC5238] (Phelan, T., “Datagram Transport Layer Security (DTLS) over the Datagram Congestion Control Protocol (DCCP),” May 2008.). Transports, such as UDP or DCCP do not provide session multiplexing and session-demultiplexing. In such cases, the application implementer provides this functionality by mapping a unique combination of the remote address, remote port number, local address and local port number to a session.

Each syslog message is delivered by the DTLS record protocol, which assigns a sequence number to each DTLS record. Although the DTLS implementer may adopt a queue mechanism to resolve reordering, it may not assure that all the messages are delivered in order when mapping on the UDP transport.

When DTLS runs over an unreliable transport, such as UDP, reliability is not provided. With DTLS, an originator or relay may not realize that a collector has gone down or lost its DTLS connection state so messages may be lost.

Syslog over DTLS over TCP MUST NOT be used. If a secure transport is required with TCP then the appropriate security mechanism is syslog over TLS as described in [RFC5425] (Miao, F., Ma, Y., and J. Salowey, “Transport Layer Security (TLS) Transport Mapping for Syslog,” March 2009.).

5.2.  Port Assignment

A syslog transport sender is always a DTLS client and a transport receiver is always a DTLS server.

The UDP and DCCP port [TBD] has been allocated as the default port for syslog over DTLS as defined in this document.

5.3.  Initiation

The transport sender initiates a DTLS connection by sending a DTLS Client Hello to the transport receiver. Implementations MUST support the denial of service countermeasures defined by DTLS. When these countermeasures are enabled, the transport receiver responds with a DTLS Hello Verify Request containing a cookie. The transport sender responds with a DTLS Client Hello containing the received cookie which initiates the DTLS handshake. When the DTLS handshake has finished, the transport sender MAY then send the first syslog message.

Implementations MUST support DTLS 1.1 (Rescorla, E. and N. Modadugu, “Datagram Transport Layer Security,” April 2006.) [RFC4347] and MUST support the mandatory to implement cipher suite, which is TLS_RSA_WITH_AES_128_CBC_SHA.

5.3.1.  Certificate-Based Authentication

The mandatory to implement ciphersuites for DTLS use certificates [RFC5280] (Cooper, D., Santesson, S., Farrell, S., Boeyen, S., Housley, R., and W. Polk, “Internet X.509 Public Key Infrastructure Certificate and Certificate Revocation List (CRL) Profile,” May 2008.) to authenticate peers. Both syslog transport sender (DTLS client) and syslog transport receiver (DTLS server) MUST implement certificate-based authentication. This consists of validating the certificate and verifying that the peer has the corresponding private key. The latter part is performed by DTLS. To ensure interoperability between clients and servers, the methods for certificate validation defined in [RFC5425] (Miao, F., Ma, Y., and J. Salowey, “Transport Layer Security (TLS) Transport Mapping for Syslog,” March 2009.) SHALL be implemented.

Both transport receiver and transport sender implementations MUST provide means to generate a key pair and self-signed certificate in the case that a key pair and certificate are not available through another mechanism.

The transport receiver and transport sender SHOULD provide mechanisms to record the end entity certificate or certificate fingerprint for the purpose of correlating an identity with the sent or received data.

5.4.  Sending data

All syslog messages MUST be sent as DTLS "application data". It is possible that multiple syslog messages be contained in one DTLS record, or that a syslog message be transferred in multiple DTLS records. The application data is defined with the following ABNF (Crocker, D. and P. Overell, “Augmented BNF for Syntax Specifications: ABNF,” January 2008.) [RFC5234] expression:

APPLICATION-DATA = 1*SYSLOG-FRAME

SYSLOG-FRAME = MSG-LEN SP SYSLOG-MSG

MSG-LEN = NONZERO-DIGIT *DIGIT

SP = %d32

NONZERO-DIGIT = %d49-57

DIGIT = %d48 / NONZERO-DIGIT

SYSLOG-MSG is defined in syslog (Gerhards, R., “The Syslog Protocol,” March 2009.) [RFC5424] protocol.

5.4.1.  Message Size

The message length is the octet count of the SYSLOG-MSG in the SYSLOG-FRAME. A transport receiver MUST use the message length to delimit a syslog message. There is no upper limit for a message length per se. As stated in [RFC4347] (Rescorla, E. and N. Modadugu, “Datagram Transport Layer Security,” April 2006.), each DTLS record must fit within a single DTLS datagram. When mapping onto different transports, DTLS has different record size limitations. The application implementer SHOULD determine the maximum record size allowed by DTLS protocol running over the transport in use. The message size SHOULD NOT exceed the DTLS maximum record size limitation of 2^14 bytes. To be consistent with RFC 5425, in establishing a baseline for interoperability, this specification requires that a transport receiver MUST be able to process messages with a length up to and including 2048 octets. Transport receivers SHOULD be able to process messages with lengths up to and including 8192 octets.

5.5.  Closure

A transport sender MUST close the associated DTLS connection if the connection is not expected to deliver any syslog messages later. It MUST send a DTLS close_notify alert before closing the connection. A transport sender (DTLS client) MAY choose to not wait for the transport receiver's close_notify alert and simply close the DTLS connection. Once the transport receiver gets a close_notify from the transport sender, it MUST reply with a close_notify.

When no data is received from a DTLS connection for a long time (where the application decides what "long" means), a transport receiver MAY close the connection. The transport receiver (DTLS server) MUST attempt to initiate an exchange of close_notify alerts with the transport sender before closing the connection. Transport receivers that are unprepared to receive any more data MAY close the connection after sending the close_notify alert.

Although closure alerts form part of DTLS, they, like all alerts, are not retransmitted by DTLS and so may be lost over an unreliable network.

6.  Security Policies

Syslog transport over DTLS has been designed to minimize the security and operational differences for environments where both [RFC5425] (Miao, F., Ma, Y., and J. Salowey, “Transport Layer Security (TLS) Transport Mapping for Syslog,” March 2009.) and syslog over DTLS are supported. The security policies for syslog over DTLS are the same as those described in [RFC5425] (Miao, F., Ma, Y., and J. Salowey, “Transport Layer Security (TLS) Transport Mapping for Syslog,” March 2009.).

7.  IANA Consideration

IANA is requested to assign a registered UDP and DCCP port number for syslog over DTLS. The same value as for syslog over TLS (6514) is requested.

8.  Security Considerations

The security considerations in [RFC5425] (Miao, F., Ma, Y., and J. Salowey, “Transport Layer Security (TLS) Transport Mapping for Syslog,” March 2009.), [RFC5246] (Dierks, T. and E. Rescorla, “The Transport Layer Security (TLS) Protocol Version 1.2,” August 2008.) and [RFC4347] (Rescorla, E. and N. Modadugu, “Datagram Transport Layer Security,” April 2006.) apply to this document.

9.  Acknowledgements

The authors would like to thank Wes Hardaker for his review on this proposal and contributing his valuable suggestions on the use of DTLS. Thanks also to Pasi Eronen, David Harrington, Chris Lonvick, Eliot Lear, Anton Okmyanskiy, Juergen Schoenwaelder, Richard Graveman and members of the syslog working group for their comments, suggestions and review.

10.  References

10.1. Normative References

10.2. Informative References

Authors' Addresses