| Network Working Group | A. Morton |
| Internet-Draft | AT&T Labs |
| Updates: 2544 (if approved) | July 1, 2018 |
| Intended status: Informational | |
| Expires: January 2, 2019 |
Updates for the Back-to-back Frame Benchmark in RFC 2544
draft-morton-bmwg-b2b-frame-02
Fundamental Benchmarking Methodologies for Network Interconnect Devices of interest to the IETF are defined in RFC 2544. This memo updates the procedures of the test to measure the Back-to-back frames Benchmark of RFC 2544, based on further experience.
This memo updates Section 26.4 of RFC 2544.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14[RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."
This Internet-Draft will expire on January 2, 2019.
Copyright (c) 2018 IETF Trust and the persons identified as the document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.
The IETF's fundamental Benchmarking Methodologies are defined in[RFC2544], supported by the terms and definitions in [RFC1242], and [RFC2544] actually obsoletes an earlier specification, [RFC1944]. Over time, the benchmarking community has updated [RFC2544] several times, including the Device Reset Benchmark [RFC6201], and the important Applicability Statement [RFC6815] concerning use outside the Isolated Test Environment (ITE) required for accurate benchmarking. Other specifications implicitly update [RFC2544], such as the IPv6 Benchmarking Methodologies in [RFC5180].
Recent testing experience with the Back-to-back Frame test and Benchmark in Section 26.4 of [RFC2544] indicates that an update is warranted [OPNFV-2017] [VSPERF-b2b]. This memo describes the rationale and provides the updated method.
[RFC2544] provides its own Requirements Language consistent with [RFC2119], since [RFC1944] predates [RFC2119]. Thus, the requirements presented in this memo are expressed in [RFC2119] terms, and intended for those performing/reporting laboratory tests to improve clarity and repeatability, and for those designing devices that facilitate these tests.
The scope of this memo is to define an updated method to unambiguously perform tests, measure the benchmark(s), and report the results for Back-to-back Frames (presently described Section 26.4 of [RFC2544]).
The goal is to provide more efficient test procedures where possible, and to expand reporting with additional interpretation of the results.
[RFC2544] Benchmarks rely on test conditions with constant frame sizes, with the goal of understanding what network device capability has been tested. Tests with the smallest size stress the header processing capacity, and tests with the largest size stress the overall bit processing capacity. Tests with sizes in-between may determine the transition between these two capacities. However, conditions simultaneously sending multiple frame sizes, such as those described in [RFC6985], MUST NOT be used in Back-to-back Frame testing.
Section 3 of [RFC8239] describes buffer size testing for physical networking devices in a Data Center. The [RFC8239] methods measure buffer latency directly with traffic on multiple ingress ports that overload an egress port on the Device Under Test (DUT), and are not subject to the revised calculations presented in this memo.
"Tests of this parameter are intended to determine the extent
of data buffering in the device."
Section 3.1 of [RFC1242] describes the rationale for the Back-to-back Frames Benchmark. To summarize, there are several reasons that devices on a network produce bursts of frames at the minimum allowed spacing, and it is therefore worthwhile to understand the Device Under Test (DUT) limit on the length of such bursts in practice. Also, [RFC1242] states:
After this test was defined, there have been occasional discussions of the stability and repeatability of the results, both over time and across labs. Fortunately, the Open Platform for Network Function Virtualization (OPNFV) VSPERF project's Continuous Integration (CI) testing routinely repeats Back-to-back Frame tests to verify that test functionality has been maintained through development of the test control programs. These tests were used as a basis to evaluate stability and repeatability, even across lab set-ups when the test platform was migrated to new DUT hardware at the end of 2016.
When the VSPERF CI results were examined [VSPERF-b2b], several aspects of the results were considered notable:
Further, if the Throughput tests of Section 26.1 of [RFC2544] are conducted as a prerequisite test, the number of frame sizes required for Back-to-back Frame Benchmarking can be reduced to one or more of the small frame sizes, or the results for large frame sizes can be noted as invalid in the results if tested anyway (these are the frame sizes for which the back-to-back frame rate cannot exceed the exceed the frame header processing rate of the DUT and no buffering occurs).
[VSPERF-b2b] provides the details of the calculation to estimate the actual buffer storage available in the DUT, using results from the Throughput tests for each frame size, and the maximum theoretical frame rate for the DUT links (which constrain the minimum frame spacing). Knowledge of approximate buffer storage size (in time or bytes) may be useful to estimate whether frame losses will occur if DUT forwarding is temporarily suspended in a production deployment, due to an unexpected interruption of frame processing (an interruption of duration greater than the estimated buffer would certainly cause lost frames).
The Test Setup MUST be consistent with Figure 1 of [RFC2544], or Figure 2 when the tester's sender and recover are different devices. Other mandatory testing aspects described in [RFC2544] MUST be included, unless explicitly modified in the next section.
The ingress and egress link speeds and link layer protocols MUST be specified and used to compute the maximum theoretical frame rate when respecting the minimum inter-frame gap.
The test results for the Throughput Benchmark conducted according to Section 26.1 of [RFC2544] for all [RFC2544]-RECOMMENDED frame sizes MUST be available to reduce the tested frame size list, or to note invalid results for individual frame sizes (because the burst length may be essentially infinite for large frame sizes).
Note that:[RFC1242] MUST be measured directly by the tester. Additional measurement requirements are described below in Section 5.
The Back-to-back Benchmark described in Section 3.1 of
Objective: To characterize the ability of a DUT to process back-to-back frames as defined in [RFC1242].
The Procedure follows.
From the list of RECOMMENDED Frame sizes (Section 9 of [RFC2544]), select the subset of Frame sizes whose measured Throughput was less than the maximum theoretical Frame Rate. These are the only Frame sizes where it is possible to produce a burst of frames that cause the DUT buffers to fill and eventually overflow, producing one or more discarded frames.
Each trial in the test requires the tester to send a burst of frames (after idle time) with the minimum inter-frame gap, and to count the corresponding frames forwarded by the DUT.
The duration of the trial MUST be at least 2 seconds, to allow DUT buffers to deplete.
If all frames have been received, the tester increases the length of the burst according to the search algorithm and performs another trial.
If the received frame count is less than the number of frames in the burst, then the limit of DUT processing and buffering may have been exceeded, and the burst length is determined by the search algorithm for the next trial.
@@@@ OPNFV VSPERF Test Results presented at IETF-102 will have relevance for answering these questions.
@@@@ Should a particular search algorithm be included? @@@@ Yes, probably more than one. There are multiple roles for benchmark tests (Highly repetitive CI and Highly Accurate & Repeatable Experiments).
@@@@ Should the search include trial repetition whenever frame loss is observed, to avoid the effects of background loss (un-related to buffer overflow)? @@@@ Yes, OPNFV VSPERF results illustrate the value of this, and ETSI NFV TST009 Annex B describes the theory behind this new algorithm.
The Back-to-back Frame value is the longest burst of frames that the DUT can successfully process and buffer without frame loss, as determined from the series of trials. The tester may impose a (configurable) minimum step size for burst length, and the step size MUST be reported with the results (as this influences the accuracy and variation of test results).
The test MUST be repeated N times for each frame size in the subset list, and each Back-to-back Frame value made available for further processing (below).
For each Frame size, calculate the following summary statistics for Back-to-back Frame values over the N tests:
Implied DUT Buffer Time = Average num of Back-to-back Frames / Max Theoretical Frame Rate
Further, calculate the Implied DUT Buffer Time and the Corrected DUT Buffer Time in seconds, as follows:
Corrected DUT Buffer Time =
Measured Throughput
= Implied DUT Buffer Time * --------------------------
Max Theoretical Frame Rate
The back-to-back results SHOULD be reported in the format of a table with a row for each of the tested frame sizes. There SHOULD be columns for the frame size and for the resultant average frame count for each type of data stream tested.
The number of tests Averaged for the Benchmark, N, MUST be reported.
The Minimum, Maximum, and Standard Deviation across all complete tests SHOULD also be reported.
The Corrected DUT Buffer Time SHOULD also be reported.
If the tester operates using a maximum burst length in frames, then this maximum length SHOULD be reported.
| Frame Size, octets | Ave B2B Length, frames | Min,Max,StdDev | Corrected Buff Time, Sec |
|---|---|---|---|
| 64 | 26000 | 25500,27000,20 | 0.00004 |
Static and configuration parameters:
Number of test repetitions, N
Minimum Step Size (during searches), in frames.
Benchmarking activities as described in this memo are limited to technology characterization using controlled stimuli in a laboratory environment, with dedicated address space and the other constraints [RFC2544].
The benchmarking network topology will be an independent test setup and MUST NOT be connected to devices that may forward the test traffic into a production network, or misroute traffic to the test management network. See [RFC6815].
Further, benchmarking is performed on a "black-box" basis, relying solely on measurements observable external to the DUT/SUT.
Special capabilities SHOULD NOT exist in the DUT/SUT specifically for benchmarking purposes. Any implications for network security arising from the DUT/SUT SHOULD be identical in the lab and in production networks.
This memo makes no requests of IANA.
Thanks to Trevor Cooper, Sridhar Rao, and Martin Klozik of the VSPERF project for many contributions to the testing [VSPERF-b2b]. Yoshiaki Itou has also investigated the topic, and made useful suggestions.
| [OPNFV-2017] | Cooper, T., Morton, A. and S. Rao, "Dataplane Performance, Capacity, and Benchmarking in OPNFV", June 2017. |
| [RFC8239] | Avramov, L. and J. Rapp, "Data Center Benchmarking Methodology", RFC 8239, DOI 10.17487/RFC8239, August 2017. |
| [VSPERF-b2b] | Morton, A., "Back2Back Testing Time Series (from CI)", June 2017. |