| Network Working Group | Q. Sun |
| Internet-Draft | Y. Cui |
| Intended status: Standards Track | Tsinghua University |
| Expires: October 13, 2013 | M. Siodelski |
| ISC | |
| S. Krishnan | |
| Ericsson | |
| I. Farrer | |
| Deutsche Telekom AG | |
| April 11, 2013 |
DHCPv4 over DHCPv6 Transport
draft-scskf-dhc-dhcpv4-over-dhcpv6-01
This document describes a mechanism for obtaining IPv4 parameters in IPv6 networks by carrying DHCPv4 messages over DHCPv6 transport.
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."
This Internet-Draft will expire on October 13, 2013.
Copyright (c) 2013 IETF Trust and the persons identified as the document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.
As the migration towards IPv6 continues, IPv6 only networks will become more prevalent. However, IPv4 connectivity will continue to be provided as a service over these IPv6 only networks. In addition to providing IPv4 addresses for clients of this service, other IPv4 configuration parameters may also need to be provided, (e.g. addresses of IPv4-only services).
Several approaches for provisioning such information have been already been proposed. This document describes one such approach.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119].
This document makes use of the following terms:
The architecture described in this document addresses a typical use case, whereby a DHCP client's uplink supports IPv6 only and the Service Provider's network supports IPv6 and limited IPv4 services. In this scenario, the client can only use the IPv6 network to access IPv4 services and so it must configure IPv4 services using IPv6 as the underlying transport protocol.
Although the purpose of this document is to address the problem of communication between DHCPv4 client and DHCPv4 server, the mechanisms it describes do not restrict the transported types of messages to DHCPv4. In additional, BOOTP messages can be transported using the same mechanism.
DHCP clients can be running on CPE devices, end hosts or any other device which supports the DHCP client function. At the time of writing, DHCP clients on CPE devices are relatively easier to modify compared to those implemented on end hosts. As a result, this document uses the CPE as an example for describing the mechanism. This doesn't preclude end hosts from implementing the mechanism in the future.
This mechanism works by carrying encapsulated DHCPv4 messages over DHCPv6 messages. Figure 1, below, illustrates one possible deployment architecture.
The DHCP client implements a new DHCPv6 message called BOOTREQUESTV6, which contains a new option called the BOOTP Message Option. The format of the option is described in Section 5. The client sends all DHCPv6 packets, including DHCPv4 over DHCPv6 packets, to the well-known All_DHCP_Relay_Agents_and_Servers multicast address on the DHCPv6 server port (UDP port 547).
The DHCPv6 packet can be transmitted either via Relay Agents or directly to the server. The server is referred in this document as a "Unified Server" for its capability of processing regular DHCPv6 traffic as well as DHCPv4 packets wrapped in the BOOTP Message Option. Server replies with a relevant DHCPv6 packet carrying DHCPv4 response wrapped with the BOOTP Message Option. Clients receive a response on UDP port 546.
_____________ _____________
/ \ / \
| | | |
+--------+-+ IPv6 +-+-----------+-+ IPv6 +-+--------+
| DHCP | network | DHCP | network | Unified |
| Client +---------+ Relay Agent +---------+ Server |
| (on CPE) | | | | |
+--------+-+ +-+-----------+-+ +-+--------+
| | | |
\_____________/ \_____________/
Figure 1: Architecture Overview
The BOOTP Message option carries a BOOTP message that is sent by the client or the server. Such BOOTP messages exclude any IP or UDP headers.
The format of the BOOTP Message Option is:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_BOOTP_MSG | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
. BOOTP-message .
. .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: BOOTP Message Option Format
When a client requires an IPv4 address and/or other IPv4 configuration parameters, it MUST generate a DHCPv4 message to obtain them from a DHCP server. This message is stored verbatim in the BOOTP Message Option carried by the BOOTREQUESTV6 message. A Client MUST put exactly one BOOTP Message Option into a single BOOTREQUESTV6 message. The Client sends out the BOOTREQUESTV6 message to the Well-Known multicast address, i.e. All_DHCP_Relay_Agents_and_Servers on multicast address defined in [RFC3315].
When a client receives a BOOTREPLYV6 message, it MUST look for the BOOTP Message Option within this message. If this option is not found, the BOOTREPLYV6 message is discarded. If the BOOTP Message Option is found, the client extracts the DHCPv4 message it contains and processes it as described in section 4.4 of [RFC2131].
As the DHCPv4 and DHCPv6 clients are running on the same host, the client MUST implement [RFC4361] to ensure that the device correctly identifies itself.
When a DHCPv6 relay agent receives a BOOTREQUESTV6 message, it MUST handle the message as described in section 20.1.1 of [RFC3315].
A DHCPv6 relay agent MUST implement the Relay behaviour described in section 20.1.1 of [RFC3315].
Additionally, the DHCPv6 relay agent MAY allow the configuration of a dedicated DHCPv4 over DHCPv6 specific destination addresses, differing from the addresses of the DHCPv6 only server(s). To implement this function, the relay checks the received DHCPv6 message type and forwards according to the following logic:
The above logic only allows for separate relay destinations configured on the relay agent closest to the client (single relay hop). Multiple relaying hops are not considered in this document.
When a Unified Server receives a BOOTREQUESTV6 message from a client, it searches for a BOOTP Message Option. If this option is missing, the server discards the packet. The Server MAY notify an administrator about the receipt of a malformed packet. The mechanism for this notification is out of scope for this document
If the server finds a valid BOOTP Message Option, it extracts the original DHCPv4 message sent by the client. This message is passed to the DHCPv4 server engine, which generates a response to the as specified in [RFC2131]. The server places the DHCPv4 response message, in the payload of a BOOTP Message Option, which it puts into the BOOTREPLYV6 message.
If the BOOTREQUESTV6 message was received directly by the server, the BOOTREPLYV6 message MUST be unicast from the interface on which the original message was received.
If the BOOTREQUESTV6 message was received in a Relay-forward message, the server creates a Relay-reply message with the BOOTREPLYV6 message in the payload of a Relay Message Option. This is analogous to other types of DHCPv6 messages as described in [RFC3315]. The server unicasts the Relay-reply message directly to the IP address of the relay agent from which the Relay-forward message was received.
In this specification, DHCPv6 is made a 'transport protocol' for DHCPv4 messages over an IPv6 network. In order to bypass firewalls or network authentication gateways, a malicious attacker may leverage this feature to convey other messages using DHCPv6, i.e. use DHCPv6 as a type of tunnel. However, the potential risk from this is no greater than with current DHCPv4 and DHCPv6 practice.
IANA is kindly requested to allocate one DHCPv6 option code to the OPTION_BOOTP_MSG and two DHCPv6 message type codes to the BOOTREQUESTV6 and BOOTREPLYV6.
Many thanks to Ted Lemon, Bernie Volz, Tomek Mrugalski, Yuchi Chen and Cong Liu, for their great contributions to the draft.
| [RFC2131] | Droms, R., "Dynamic Host Configuration Protocol", RFC 2131, March 1997. |
| [RFC3315] | Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C. and M. Carney, "Dynamic Host Configuration Protocol for IPv6 (DHCPv6)", RFC 3315, July 2003. |
| [RFC4361] | Lemon, T. and B. Sommerfeld, "Node-specific Client Identifiers for Dynamic Host Configuration Protocol Version Four (DHCPv4)", RFC 4361, February 2006. |
| [RFC2119] | Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. |
| [I-D.ietf-dhc-dhcpv4-over-ipv6] | Cui, Y., Wu, P., Wu, J. and T. Lemon, "DHCPv4 over IPv6 Transport", Internet-Draft draft-ietf-dhc-dhcpv4-over-ipv6-05, September 2012. |