Internet DRAFT - draft-defoy-5g-session-continuity-support-in-mptcp
draft-defoy-5g-session-continuity-support-in-mptcp
Network Working Group X. de Foy
Internet-Draft U. Olvera-Hernandez
Intended status: Informational InterDigital Communications
Expires: April 22, 2019 U. Chunduri
Huawei USA
Oct 19, 2018
5G Session Continuity Support in MPTCP
draft-defoy-5g-session-continuity-support-in-mptcp-00
Abstract
This document describes how 5G session continuity can affect MPTCP.
For now only potential performance issues are identified. This
document aims to document discussions that took place at the IETF on
this subject, to facilitate future deployment of MPTCP over 5G.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 22, 2019.
Copyright Notice
Copyright (c) 2018 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
de Foy, et al. Expires April 22, 2019 [Page 1]
Internet-Draft MPTCP IN 5G Oct 2018
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction and Goal . . . . . . . . . . . . . . . . . . . . 2
2. Problem Statement . . . . . . . . . . . . . . . . . . . . . . 2
2.1. 5G Will Not Hide Session Continuity from MPTCP Any Longer 2
2.2. Detailed Issues . . . . . . . . . . . . . . . . . . . . . 3
3. Potential Solutions . . . . . . . . . . . . . . . . . . . . . 3
3.1. Alternative #1: No Change to MPTCP Protocol . . . . . . . 4
3.2. Alternative #2: Explicit signaling of Session Continuity
Type . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.3. Alternative #3: Client-Driven Handling . . . . . . . . . 6
4. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 6
5. Security Considerations . . . . . . . . . . . . . . . . . . . 7
6. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 7
7. Informative References . . . . . . . . . . . . . . . . . . . 7
Appendix A. IP Address Session Continuity Service Type . . . . . 8
Appendix B. Overview of 5G Session and Service Continuity . . . 8
B.1. SSC mode 1 . . . . . . . . . . . . . . . . . . . . . . . 9
B.2. SSC mode 2 . . . . . . . . . . . . . . . . . . . . . . . 9
B.3. SSC mode 3 . . . . . . . . . . . . . . . . . . . . . . . 9
Appendix C. Example of MPTCP Client Implementations Behavior
with 5G SSC . . . . . . . . . . . . . . . . . . . . 10
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 11
1. Introduction and Goal
MPTCP [RFC6824] is being deployed and widely adopted in today's smart
devices, which typically have multiple network interfaces such as
Cellular and Wifi. It provides reliability, bandwidth aggregation
capability, and handover efficiency.
This document describes how 5G session continuity can affect MPTCP.
For now only potential performance issues are identified. This
document aims to document discussions that took place at the IETF on
this subject, to facilitate future deployment of MPTCP over 5G.
2. Problem Statement
2.1. 5G Will Not Hide Session Continuity from MPTCP Any Longer
In 4G [_3GPP.23.401], a single long-term IP address was provided to
the end device. Session continuity was performed through a fixed
anchor, and effectively hidden from MPTCP.
de Foy, et al. Expires April 22, 2019 [Page 2]
Internet-Draft MPTCP IN 5G Oct 2018
In 5G, session continuity won't always be hidden from MPTCP. 3
session continuity modes are defined in [_3GPP.23.501]: in some
cases, what used to be a single IP address will now be visible by
MPTCP as multiple successive and possibly concurrent IP addresses.
More details on session continuity in 5G are provided in Appendix B.
In particular, the 5G term for session continuity is Session and
Service Continuity (SSC), and the 3 SSC modes correspond to: fixed
anchor (mode 1), distributed anchor with break-before-make (mode 2),
and distributed anchor with make-before-break (mode 3).
While it could be possible to hide 5G session continuity to MPTCP by
limiting its usage to SSC mode 1, it would limit the range of
applications that can benefit from MPTCP, since SSC modes 2 and 3
enable low-latency mobility. In the rest of this document, we will
study how MPTCP can deal with any SSC mode.
2.2. Detailed Issues
Overall we don't expect SSC modes 2 and 3 will cause MPTCP to break,
but we do expect inefficiencies in some scenarios. The following
potential inefficiencies have been identified:
*Supporting make-before-break (MBB) without wasting resources*:
the old IP address should be released shortly after a MBB handover
has been performed. Not too early (wait for traffic using the new
IP address to ramp up), and not too late (to release resources to
the mobile network). Today's MPTCP implementations are likely to
keep using the old IP address as long as it is available, which
will prevent the network from releasing the resources early.
*Supporting break-before-make (BBM) without temporarily switching
to backup*: if there is a backup IP address, MPTCP peers should
not switch to using this backup IP address immediately, and
instead should wait for a new replacement IP address to be used
after BBM handover. Today's MPTCP implementations are likely to
switch back-and-forth between active and backup IP addresses,
which can lead to network and power consumption inefficiencies.
3. Potential Solutions
Locally on the mobile node itself, a MPTCP implementation will need
some information to support session continuity. For each IP address,
MPTCP should be aware of the following information:
Is the IP address provided by a mobile network, and, if
applicable, what is the session continuity type associated with
de Foy, et al. Expires April 22, 2019 [Page 3]
Internet-Draft MPTCP IN 5G Oct 2018
the IP address? Session continuity type overview and references
are listed in Appendix A.
The original IP address of the session this IP address is a part
of (unless this IP address is the original IP address itself).
The client can use this (address type, original IP address) tuple to
locally support session continuity. An example of implementation
behavior is given in Appendix C. For example, a local MPTCP client
implementation can use this tuple to appropriately mark new subflows
as "backup", when they replace original subflows marked as "backup".
With regards to the behavior of the remote MPTCP peer, three
alternatives are identified at this point:
In alternative #1, we do not implement any specific support in the
MPTCP protocol.
In alternative #2, the MPTCP client sends to its remote peer, over
MPTCP signaling, the tuple (address type, original IP address) for
each IP address.
In alternative #3, we use an hybrid solution, where the tuple
(address type, original IP address) is not sent to the remote
peer; instead, the local MPTCP client influences the remote peer
using modified MPTCP signaling.
Some enhancements to the MPTCP protocol are proposed in alternatives
#2 and #3. Further discussions and analysis are expected to
determine which alternative is best suited for MPTCP.
3.1. Alternative #1: No Change to MPTCP Protocol
This section evaluates the impact of not implementing any specific
support in the MPTCP protocol, for the issues mentioned earlier
(although the MPTCP client implementation on a 5G device should still
be updated to be session continuity-aware, as in all 3 alternatives,
to implement client-side behavior such as properly assigning the
"backup" property).
*Supporting make-before-break (MBB) without wasting resources*:
not implementing any specific support in MPTCP can be acceptable
(1) if the impact on the network resource usage is acceptable, and
(2) if the impact on performances is acceptable. Both those
impacts are likely to vary in practice. About (1): unmodified
MPTCP will keep using the old IP address until the network
physically reclaims the network resources when the lifetime of the
old IP address is over. This lifetime is not specified and may be
de Foy, et al. Expires April 22, 2019 [Page 4]
Internet-Draft MPTCP IN 5G Oct 2018
implementation specific. About (2): when the old IP address is
brought down by the network, some in-flight segments will need to
be re-sent on other subflows. The impact may therefore vary
depending on throughput and the nature of the application.
*Supporting break-before-make (BBM) without temporarily switching
to backup*: if we do not attempt to address this issue, we count
on the fact that (1) the effect of temporarily switching back and
forth between radios has an "acceptable impact", and/or (2) the
problem is rare enough. Again, these are points that may be best
estimated after deployment, and that could evolve over time, with
applications usage patterns. About (2): this issue is specific to
SSC mode 2; applications that exchange bursts of traffic (e.g.
browsers), which are well suited for mode 2, may reduce the rate
of occurrence.
3.2. Alternative #2: Explicit signaling of Session Continuity Type
In this case, options that implicitly or explicitly add a new IP
address (MP_CAPABLE, ADD_ADDR, MP_JOIN) are associated with
additional fields (address type, original IP address index). This
way, both MPTCP peers share the same information about the IP
address, with regards to session continuity.
*Supporting make-before-break (MBB) without wasting resources*:
after the local client creates a new subflow using the new IP
address, local client and remote peer both start using it. They
continue sending traffic on the old subflow (i.e. subflow using
the old IP address), until the traffic usage ramps up on the new
subflow. At this point, both peers stop sending new segments on
the the old subflow. Once in-flight segments are received and
acked, the local client resets the old subflow and then remove the
old IP address, which makes it possible for the network to
ultimately reclaim the network resources.
*Supporting break-before-make (BBM) without temporarily switching
to backup*: remote peer and local client are both aware that a BBM
is a normal occurrence for IP addresses associated with a "non
persistent" type. Therefore, remote peer and local client should
both wait for a given time before using a backup subflow. This
"BBM timeout" parameter may for example be sent in a new field by
the local client to the remote peer, when explicitly or implicitly
adding the original "non persistent" IP address.
de Foy, et al. Expires April 22, 2019 [Page 5]
Internet-Draft MPTCP IN 5G Oct 2018
3.3. Alternative #3: Client-Driven Handling
In this case, session continuity type is not sent over MPTCP
signaling. The local client uses "generic" (i.e. non-session-
continuity-specific) MPTCP signaling to control the behavior of the
remote peer. Some minor modifications of the MPTCP protocol may be
needed.
*Supporting make-before-break (MBB) without wasting resources*:
the local client creates a new subflow using the new IP address.
After enough time passed for traffic to ramp up on the new
subflow, the local client instructs the remote peer to stop using
the old subflow (i.e. subflow using the old IP address), without
abruptly closing the subflow, to avoid re-sending segments on the
new subflow and affect performance. To do this, the local client
sets the priority of the old subflow to "backup", and then waits
until in-flight segments are received and acked. At this point,
the local client resets the old, now unused subflow. Once no more
subflows are using the old IP address, the local client removes it
using REMOVE_ADDR.
A new subflow reset reason code "path management decision" may
be defined to indicate that a peer took the decision to
permanently remove a subflow (this new reason code may also be
useful in alternative #1).
As a minor improvement, a new priority "inactive" may also be
defined. "Inactive" would be similar to backup, except that it
would never become active, even if no other active subflow
exist. This could avoid rare issues when losing active
subflows while removing an old subflow.
*Supporting break-before-make (BBM) without temporarily switching
to backup*: the local client associates a timer value to a backup
priority on a subflow, e.g. using a new field in the MP_PRIO
option. When all active subflows are lost, MPTCP peers must wait
for the specified time before using the backup subflow. To avoid
switching between backup and active subflows in BBM, the local
client should ensure that all backup priority timers are set to a
value that is higher that the maximum BBM transition time.
4. IANA Considerations
This document requests no IANA actions.
de Foy, et al. Expires April 22, 2019 [Page 6]
Internet-Draft MPTCP IN 5G Oct 2018
5. Security Considerations
No new security considerations are identified at this time.
6. Acknowledgements
Thanks to following people for contributing through discussions or
reviews: Christoph Paasch, Michelle Perras, Debashish Purkayastha,
Akbar Rahman, Sri Gundavelli, Philip Eardley, Yoshifumi Nishida.
7. Informative References
[_3GPP.23.401]
3GPP, "General Packet Radio Service (GPRS) enhancements
for Evolved Universal Terrestrial Radio Access Network
(E-UTRAN) access", 3GPP TS 23.401 15.3.0, 3 2018,
<http://www.3gpp.org/ftp/Specs/html-info/23401.htm>.
[_3GPP.23.501]
3GPP, "System Architecture for the 5G System", 3GPP
TS 23.501 15.14.0, 3 2018,
<http://www.3gpp.org/ftp/Specs/html-info/23501.htm>.
[I-D.feng-dmm-ra-prefixtype]
Feng, W. and D. Moses, "Router Advertisement Prefix Option
Extension for On-Demand Mobility", draft-feng-dmm-ra-
prefixtype-03 (work in progress), September 2018.
[I-D.ietf-dmm-ondemand-mobility]
Yegin, A., Moses, D., Kweon, K., Lee, J., Park, J., and S.
Jeon, "On Demand Mobility Management", draft-ietf-dmm-
ondemand-mobility-15 (work in progress), July 2018.
[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
DOI 10.17487/RFC4861, September 2007,
<https://www.rfc-editor.org/info/rfc4861>.
[RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
Address Autoconfiguration", RFC 4862,
DOI 10.17487/RFC4862, September 2007,
<https://www.rfc-editor.org/info/rfc4862>.
[RFC6824] Ford, A., Raiciu, C., Handley, M., and O. Bonaventure,
"TCP Extensions for Multipath Operation with Multiple
Addresses", RFC 6824, DOI 10.17487/RFC6824, January 2013,
<https://www.rfc-editor.org/info/rfc6824>.
de Foy, et al. Expires April 22, 2019 [Page 7]
Internet-Draft MPTCP IN 5G Oct 2018
Appendix A. IP Address Session Continuity Service Type
The "session continuity service type" (SCS type) characterises the
session continuity properties an IP address allocated by a mobile
network. It has been defined for on-demand mobility management
[I-D.ietf-dmm-ondemand-mobility], as:
FIXED IP address: valid for a very long time, for session
continuity and IP address reachability.
SESSION_LASTING IP address: valid for the lifetime of an IP
session, even if the mobility host moves.
NON_PERSISTENT IP address: which does not provide session
continuity nor IP address reachability.
GRACEFUL_REPLACEMENT IP address: similar to a non-persistent
address, but adding a limited graceful period for the transition
from one address to another.
This information can be conveyed to the device by the network that
allocates the address: for example, as described in
[I-D.feng-dmm-ra-prefixtype], the SCS type of an IP address may be
conveyed through router advertisements.
The session continuity service types are planned to be used in the 5G
specification from 3GPP, as properties of the IP addresses allocated
by the network to mobile devices. There is a 1:1 relationship
between the session continuity service type of the initial IP address
of a session and the SSC mode of this session (SSC mode is a 3GPP
concept discussed in the following section).
Appendix B. Overview of 5G Session and Service Continuity
One of the goals of 5G systems, as outlined in [_3GPP.23.501], is to
enable low latency services and access to local data networks where
mobility anchors can be deployed close to devices, thereby satisfying
use cases with stringent transmission delay and high reliability.
Mobility in 4G networks, as described at the architecture level in
[_3GPP.23.401], was based on a central mobility solution that made it
difficult to relocate mobility anchors closer to the end user. In
contrast, 5G uses a distributed mobility solution based on multiple
anchors providing different IP addresses as the device moves from one
area to another.
In 5G, every unit of a network connectivity service (PDU session) has
a type which can be IP (IPv4 or IPv6), Ethernet or unstructured.
Different PDU sessions will typically correspond to distinct network
de Foy, et al. Expires April 22, 2019 [Page 8]
Internet-Draft MPTCP IN 5G Oct 2018
interfaces on the device (though this is not explicit in the
standard, and some implementations may possibly behave differently).
In 4G networks, session continuity is enabled by anchoring a PDN
Connection (as PDU Sessions are referred to in 4G networks) to a P-GW
which allocates an IP address to the mobile device: PDN connection
and IP address allocation are maintained as long as the device
remains attached to the network, even when the device moves around.
In 5G, different types of session continuity can be provided, and are
indicated by a "Session and Service Continuity" (SSC) mode value of
1, 2 or 3 (defined in [_3GPP.23.501] section 5.6.9). Every PDU
session is associated with a single SSC mode, which cannot be changed
on this PDU session. The following sub-sections will study how 5G
handles each SSC mode, and potential effects on MPTCP.
B.1. SSC mode 1
In SSC mode 1 the same network anchor is kept regardless of device
location. An application running on the device will therefore be
able to keep using the same IP address on the same interface.
Additionally, in SSC mode 1, the network may decide to add and
remove, dynamically, additional network anchors (and therefore IP
addresses) to the PDU session, while always keeping the initial one.
This would result in a second IP address being allocated on the
network interface with which the long-term IP address is associated.
This second IP address may be brought down at any time.
B.2. SSC mode 2
SSC mode 2 has a break-before-make behavior. When the device leaves
the service area of its first network anchor, the network stops using
it and starts using a second network anchor closer to the device.
(Such service areas may have a highly variable size depending on
network deployments.) On the device, this can result in the
currently used network interface being brought down, and after a
short time a new network interface being brought up. The time
between these 2 events is not standardized and implementation
dependent.
B.3. SSC mode 3
SSC mode 3 has a make-before-break behavior. When the device leaves
the service area of its first network anchor, the network selects a
second network anchor closer to the device, and either creates a new
PDU session (i.e. new IP address on new network interface) or share
the existing PDU session (i.e. new IP address on same network
interface). The first network anchor keeps being used for a given
de Foy, et al. Expires April 22, 2019 [Page 9]
Internet-Draft MPTCP IN 5G Oct 2018
time period, which is communicated to the device by the network using
the "valid lifetime" field of a prefix information option in a router
advertisement ([RFC4861], [RFC4862]). 5G specifications does not
mandate a specific range for this valid lifetime. The first/older IP
address should not be used to create any new traffic ([RFC4862]
section 5.5.4). In some implementations, the network (SMF) may
decide to release the first network anchor as soon as it stops
carrying traffic.
There is no limit set by the 5G standard for the number of
concurrently used network anchors. We expect that in usual cases the
first network anchor will be released before a third network anchor
starts being used. Nevertheless, to our knowledge nothing prevents a
5G system deployment to allow a third network anchor to be selected
while the first one is still in use.
On the 5G device, when using SSC mode 3, mobility will therefore
result in a new IP address being configured, either on the same
network interface initially used, or on a different network
interface. In general, an application will see a single cellular-
facing IP address, and during transient phase it will see 2 IP
addresses (with a possibility for more than 2 concurrent IP addresses
on some 5G system implementations).
Appendix C. Example of MPTCP Client Implementations Behavior with 5G
SSC
The following describes at high level how a MPTCP implementation
could be modified to locally support 5G session continuity. A
discussion of how this behavior can be extended to the remote MPTCP
peer is a core subject of this draft, and discussed in the body of
the draft.
For simplicity, we consider a case where MPTCP is used in a client
with 2 IP addresses, one of them being provided by a mobile network.
The behaviors described here depend on the session continuity type of
the initial mobile network-provided IP address, which has a 1:1
mapping to the 5G SCC mode used.
When the initial IP address session continuity type is FIXED or
SESSION_LASTING (i.e. in SCC mode 1):
MPTCP should not close all subflows originated from this original
IP address at any point during the session, since this IP address
is the only one that is guaranteed, under normal circumstances, to
be maintained over time for this application.
de Foy, et al. Expires April 22, 2019 [Page 10]
Internet-Draft MPTCP IN 5G Oct 2018
At any time during the session, a new IP address of SCS type
NON_PERSISTENT may become available. MPTCP may create new
subflows for the application, using this IP address (this IP
address is likely to provide shorter path subflows, but may
disappear at any time).
When the initial IP address session continuity type is NON_PERSISTENT
(i.e. in SCC mode 2):
At any point in time, the current NON_PERSISTENT IP address may be
taken down by the network stack. The MPTCP stack should wait for
another NON_PERSISTENT IP address to be made available by the
network stack. If such an address is made available within a
given time limit, the MPTCP stack should create new subflows using
this new address (effectively following the existing break-before-
make behavior present in MPTCP).
Additionally, if an initial backup IP address is a NON_PERSISTENT
address, the MPTCP stack should consider any subsequent
NON_PERSISTENT IP address as a backup IP address in replacement of
the initial NON_PERSISTENT address.
When the initial IP address session continuity type is
GRACEFUL_REPLACEMENT (i.e. in SCC mode 3):
At any point in time, a new GRACEFUL_REPLACEMENT IP address may be
made available by the network stack. The MPTCP stack must create
new subflows using this new address, gracefully transfer traffic
to these new subflow(s), and close subflow(s) using the previous
GRACEFUL_REPLACEMENT IP address before its scheduled closing
(known by obtaining the valid lifetime of the IP address from the
operating system).
Additionally, if an initial backup IP address is a
GRACEFUL_REPLACEMENT address, the MPTCP stack should consider any
subsequent GRACEFUL_REPLACEMENT IP address as the new backup IP
address, in replacement of the first GRACEFUL_REPLACEMENT IP
address.
Authors' Addresses
Xavier de Foy
InterDigital Communications, LLC
1000 Sherbrooke West
Montreal H3A 3G4
Canada
Email: Xavier.Defoy@InterDigital.com
de Foy, et al. Expires April 22, 2019 [Page 11]
Internet-Draft MPTCP IN 5G Oct 2018
Ulises Olvera-Hernandez
InterDigital Communications, LLC
64 Great Eastern Street
London EC2A 3QR
England
Email: Ulises.Olvera-Hernandez@InterDigital.com
Uma Chunduri
Huawei USA
2330 Central Expressway
Santa Clara, CA 95050
USA
Email: uma.chunduri@huawei.com
de Foy, et al. Expires April 22, 2019 [Page 12]