Internet DRAFT - draft-herbert-gue

draft-herbert-gue



 



Internet Draft                                                T. Herbert
<draft-herbert-gue-03.txt>                                        Google
Category: Standard track                                         L. Yong
Expires September 2015                                        Huawei USA
                                                                  O. Zia
                                                               Microsoft
                                                           March 6, 2015

                       Generic UDP Encapsulation
                       <draft-herbert-gue-03.txt>

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.  

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress." 

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt 

   The list of Internet-Draft Shadow Directories can be accessed at 
   http://www.ietf.org/shadow.html

   This Internet-Draft will expire on September 7, 2015.

Copyright Notice

   Copyright (c) 2014 IETF Trust and the persons identified as the
   document authors. All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document. Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.



 


Herbert, Yong, Zia       Expires September 2015                 [Page 1]

Internet Draft              herbert-gue.txt                March 6, 2015


Abstract          

   This specification describes Generic UDP Encapsulation (GUE), which
   is a scheme for using UDP to encapsulate packets of arbitrary IP
   protocols for transport across layer 3 networks. By encapsulating
   packets in UDP, specialized capabilities in networking hardware for
   efficient handling of UDP packets can be leveraged. GUE specifies
   basic encapsulation methods upon which higher level constructs, such
   tunnels and overlay networks for network virtualization, can be
   constructed. GUE is extensible by allowing optional data fields as
   part of the encapsulation, and is generic in that it can encapsulate
   packets of various IP protocols.

Table of Contents

   1. Introduction  . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2. Packet formats  . . . . . . . . . . . . . . . . . . . . . . . .  4
     2.1. GUE header preamble . . . . . . . . . . . . . . . . . . . .  4
     2.2. GUE header  . . . . . . . . . . . . . . . . . . . . . . . .  5
     2.3. Flags and optional fields . . . . . . . . . . . . . . . . .  6
     2.4 Private data . . . . . . . . . . . . . . . . . . . . . . . .  7
   3. Message types . . . . . . . . . . . . . . . . . . . . . . . . .  7
     3.1. Control messages  . . . . . . . . . . . . . . . . . . . . .  7
     3.2. Data messages . . . . . . . . . . . . . . . . . . . . . . .  8
   4. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .  8
     4.1. Network tunnel encapsulation  . . . . . . . . . . . . . . .  9
     4.2. Transport layer encapsulation . . . . . . . . . . . . . . .  9
     4.3. Encapsulator operation  . . . . . . . . . . . . . . . . . .  9
     4.4. Decapsulator operation  . . . . . . . . . . . . . . . . . .  9
     4.5. Router and switch operation . . . . . . . . . . . . . . . . 10
     4.6. Middlebox interactions  . . . . . . . . . . . . . . . . . . 10
     4.7. NAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
     4.8. Checksum Handling . . . . . . . . . . . . . . . . . . . . . 11
       4.8.1. Checksum requirements . . . . . . . . . . . . . . . . . 11
       4.8.2. GUE header checksum . . . . . . . . . . . . . . . . . . 11
       4.8.3. UDP Checksum with IPv4  . . . . . . . . . . . . . . . . 11
       4.8.4. UDP Checksum with IPv6  . . . . . . . . . . . . . . . . 12
     4.9. MTU and fragmentation issues  . . . . . . . . . . . . . . . 13
     4.10 Congestion control  . . . . . . . . . . . . . . . . . . . . 13
   5. Inner flow identifier properties  . . . . . . . . . . . . . . . 13
     5.1. Flow classification . . . . . . . . . . . . . . . . . . . . 13
     5.2. Inner flow identifier properties  . . . . . . . . . . . . . 14
   6. Motivation for GUE  . . . . . . . . . . . . . . . . . . . . . . 15
   7. Security Considerations . . . . . . . . . . . . . . . . . . . . 16
     7.1. GUE security fields . . . . . . . . . . . . . . . . . . . . 17
     7.2. GUE and IPsec . . . . . . . . . . . . . . . . . . . . . . . 17
   8. IANA Consideration  . . . . . . . . . . . . . . . . . . . . . . 17
   9. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . . . 18
 


Herbert, Yong, Zia       Expires September 2015                 [Page 2]

Internet Draft              herbert-gue.txt                March 6, 2015


   10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 18
     10.1. Normative References . . . . . . . . . . . . . . . . . . . 18
     10.2. Informative References . . . . . . . . . . . . . . . . . . 18
   Appendix A: NIC processing for GUE . . . . . . . . . . . . . . . . 19
     A.1. Receive multi-queue . . . . . . . . . . . . . . . . . . . . 20
     A.2. Checksum offload  . . . . . . . . . . . . . . . . . . . . . 20
       A.2.1. Transmit checksum offload . . . . . . . . . . . . . . . 20
       A.2.2. Receive checksum offload  . . . . . . . . . . . . . . . 21
     A.3. Transmit Segmentation Offload . . . . . . . . . . . . . . . 22
     A.4. Large Receive Offload . . . . . . . . . . . . . . . . . . . 22
   Appendix B: Privileged ports . . . . . . . . . . . . . . . . . . . 23
   Appendix C: Inner flow identifier as a route selector  . . . . . . 23
   Appendix D: Hardware protocol implementation considerations  . . . 23
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 24

1. Introduction

   This specification describes Generic UDP Encapsulation (GUE) which is
   a general method for encapsulating packets of arbitrary IP protocols
   within User Datagram Protocol (UDP) [RFC0768] packets. Encapsulating
   packets in UDP facilitates efficient transport across networks.
   Networking devices widely provide protocol specific processing and
   optimizations for UDP (as well as TCP) packets. Packets for atypical
   IP protocols (those not usually parsed by networking hardware) can be
   encapsulated in UDP packets to maximize deliverability and to
   leverage flow specific mechanisms for routing and packet steering.

   GUE provides an extensible header format for including optional data
   in the encapsulation header. This data potentially covers items such
   as virtual networking identifier, security data for validating or
   authenticating the GUE header, congestion control data, etc. GUE also
   allows private optional data in the encapsulation header. This
   feature can be used by a site or implementation to define local
   custom optional data, and allows experimentation of options that may
   eventually become standard.













 


Herbert, Yong, Zia       Expires September 2015                 [Page 3]

Internet Draft              herbert-gue.txt                March 6, 2015


2. Packet formats

   A GUE packet is comprised of a UDP packet whose payload is a GUE
   header followed by a payload which is either an encapsulated packet
   of some IP protocol or a control message (like an OAM message). A GUE
   packet has the general format:

   +-------------------------------+
   |                               |
   |        UDP/IP header          |
   |                               |
   |-------------------------------|
   |                               |
   |         GUE Header            |
   |                               |
   |-------------------------------| 
   |                               |                              
   |      Encapsulated packet      |
   |      or control message       |
   |                               |
   +-------------------------------+

   The GUE header is variable length as determined by the presence of
   optional fields.

2.1. GUE header preamble

   The first byte of the GUE header provides the GUE protocol version
   number, indicator of a control or data message, and header length:

    0
    0 1 2 3 4 5 6 7
   +-+-+-+-+-+-+-+-+ 
   |Ver|C|   Hlen  |        
   +-+-+-+-+-+-+-+-+

   Contents are:

      o Ver: GUE protocol version. The rest of the fields after the
        preamble are defined based on the version. This field is two
        bits allowing four possible values.

      o Control flag: When set indicates a control message, not set
        indicates a data message.

      o Hlen: Length in 32-bit words of the GUE header, including
        optional fields but not the first four bytes of the header.
        Computed as (header_len - 4) / 4. All GUE headers are a multiple
 


Herbert, Yong, Zia       Expires September 2015                 [Page 4]

Internet Draft              herbert-gue.txt                March 6, 2015


        of four bytes in length. Maximum header length is 132 bytes.


2.2. GUE header

   The header format for version 0x0 of GUE in UDP is:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |        Source port            |      Destination port         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           Length              |          Checksum             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0x0|C|   Hlen  |  Proto/ctype  |            Flags            |E|
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   ~                       Fields (optional)                       ~
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                   Extension flags (optional)                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   ~                    Extension fields (optional)                ~
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   ~                    Private data (optional)                    ~
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The contents of the UDP header are:

      o Source port (inner flow identifier): This should be set to a
        value that represents the encapsulated flow. The properties of
        the inner flow identifier are described below.

      o Destination port: The GUE assigned port number, 6080.

      o Length: Canonical length of the UDP packet (length of UDP header
        and payload).

      o Checksum: Standard UDP checksum.

   The GUE header consists of:

      o Preamble byte: Version number (0x0), C bit, and header length.

 


Herbert, Yong, Zia       Expires September 2015                 [Page 5]

Internet Draft              herbert-gue.txt                March 6, 2015


      o Proto/ctype: When the C bit is set this field contains a control
        message type for the payload. When C bit is not set, the field
        holds the IP protocol number for the encapsulated packet in the
        payload. The control message or encapsulated packet begins at
        the offset provided by Hlen.

      o Flags. Header flags that may be allocated for various purposes
        and may indicate presence of optional fields. Undefined header
        flag bits must be set to zero on transmission.

      o 'E' Extension flag. Indicates presence of extension flags option
        in the optional fields.

      o Fields: Optional fields whose presence is indicated by
        corresponding flags. 

      o Extension flags: An optional field indicated by the E bit. This
        field provides an additional set of 32 header bit flags for the
        header.

      o Extension fields: Optional fields whose presence is indicated by
        corresponding extension flags.

      o Private data: Optional private data. If private data is present
        it immediately follows that last field present in the header.
        The length of this data is determined by subtracting the
        starting offset from the header length.

2.3. Flags and optional fields

   Flags and associated optional fields are the primary mechanism of
   extensibility in GUE. There are sixteens flag bits in the primary GUE
   header with one being reserved to indicate that an optional extension
   flags field is present. The extension flags field contains an
   additional thirty-two flag bits.

   A flag may indicate presence of optional fields. The size of an
   optional field indicated by a flag must be fixed.

   Flags may be paired together to allow different lengths for an
   optional field. For example, if two flag bits are paired, a field may
   possibly be three different lengths. Regardless of how flag bits may
   be paired, the lengths and offsets of optional fields corresponding
   to a set of flags must be well defined.

   Optional fields are placed in order of the flags. New flags should be
   allocated from high to low order bit contiguously without holes.
   Flags allow random access, for instance to inspect the field
 


Herbert, Yong, Zia       Expires September 2015                 [Page 6]

Internet Draft              herbert-gue.txt                March 6, 2015


   corresponding to the Nth flag bit, an implementation only considers
   the previous N-1 flags to determine the offset. Flags after the Nth
   flag are not pertinent in calculating the offset of the Nth flag.

   Flags (or paired flags) are idempotent such that new flags should not
   cause reinterpretation of old flags. Also, new flags should not alter
   interpretation of other elements in the GUE header nor how the
   message is parsed (for instance, in a data message the proto/ctype
   field always holds an IP protocol number as an invariant).

2.4 Private data

   An implementation may use private data for its own use. The private
   data immediately follows the last field in the GUE header and is not
   a fixed length. This data is considered part of the GUE header and
   must be accounted for in header length (Hlen). The length of the
   private data must be a multiple of four and is determined by
   subtracting the offset of private data in the GUE header from the
   header length. Specifically:

      Private_length = (Hlen * 4) - Length(flags)

   Where "Length(flags)" returns the sum of lengths of all the optional
   fields present in the GUE header. When there is no private data
   present, length of the private data is zero.

   The semantics and interpretation of private data are implementation
   specific. A encapsulator and decapsulator MUST agree on the meaning
   of private data before using it. The private data may be structured
   as necessary, for instance it might contain its own set of flags and
   optional fields.

   If a decapsulator receives a GUE packet with private data, it MUST
   validate the private data appropriately. If a decapsulator does not
   expect private data from an encapsulator the packet MUST be dropped.
   If a decapsulator cannot validate the contents of private data per
   the provided semantics the packet MUST also be dropped. An
   implementation may place security data in GUE private data which must
   be verified for packet acceptance.

3. Message types

3.1. Control messages

   Control messages are indicated in the GUE header when the C bit is
   set. The payload is interpreted as a control message with type
   specified in the proto/ctype field. The format and contents of the
   control message are indicated by the type and can be variable length.
 


Herbert, Yong, Zia       Expires September 2015                 [Page 7]

Internet Draft              herbert-gue.txt                March 6, 2015


   Other than interpreting the proto/ctype field as a control message
   type, the meaning and semantics of the rest of the elements in the
   GUE header are the same as that of data messages. Forwarding and
   routing of control messages should be the same as that of a data
   message with the same outer IP and UDP header and GUE flags-- this
   ensures that a control message can be created which follows the same
   path as a data message.

   Control messages can be defined for OAM type messages. For instance,
   an echo request and corresponding echo reply message may be defined
   to test for liveness.

3.2. Data messages

   Data messages are indicated in GUE header with C bit not set. The
   payload of a data message is interpreted as an encapsulated packet of
   an IP protocol indicated in the proto/ctype field. The packet
   immediately follows the GUE header.

   Data messages are a primary means of encapsulation and can be used to
   create tunnels for overlay networks.

4. Operation

   The figure below illustrates the use of GUE encapsulation between two
   servers. Sever 1 is sending packets to server 2. An encapsulator
   performs encapsulation of packets from server 1. These encapsulated
   packets traverse the network as UDP packets. At the decapsulator,
   packets are decapsulated and sent on to server 2. Packet flow in the
   reverse direction need not be symmetric; GUE encapsulation is not
   required in the reverse path.

   +---------------+                       +---------------+
   |               |                       |               |
   |   Server 1    |                       |    Server 2   |
   |               |                       |               |
   +---------------+                       +---------------+
          |                                        ^
          V                                        |
   +---------------+   +---------------+   +---------------+
   |               |   |               |   |               |
   | Encapsulator  |-->|    Layer 3    |-->| Decapsulator  |
   |               |   |    Network    |   |               |
   +---------------+   +---------------+   +---------------+

   The encapsulator and decapsulator may be co-resident with the
   corresponding servers, or may be on separate nodes in the network.

 


Herbert, Yong, Zia       Expires September 2015                 [Page 8]

Internet Draft              herbert-gue.txt                March 6, 2015


4.1. Network tunnel encapsulation

   Network tunneling can be achieved by encapsulating layer 2 or layer 3
   packets. In this case the encapsulator and decapsulator nodes are the
   tunnel endpoints. These could be routers that provide network tunnels
   on behalf of communicating servers.

4.2. Transport layer encapsulation

   When encapsulating layer 4 packets, the encapsulator and decapsulator
   should be co-resident with the servers. In this case, the
   encapsulation headers are inserted between the IP header and the
   transport packet. The addresses in the IP header refer to both the
   endpoints of the encapsulation and the endpoints for terminating the
   the transport protocol.

4.3. Encapsulator operation

   Encapsulators create GUE data messages, set the source port to the
   inner flow identifier, set flags and optional fields in the GUE
   header, and forward packets to a decapsulator.

   An encapsulator may be an end host originating the packets of a flow,
   or may be a network device performing encapsulation on behalf of
   servers (routers implementing tunnels for instance). In either case,
   the intended target (decapsulator) is indicated by the outer
   destination IP address.

   If an encapsulator is tunneling packets, that is encapsulating
   packets of layer 2 or layer 3 protocols (e.g. EtherIP, IPIP, ESP
   tunnel mode), it should follow standard conventions for tunneling of
   one IP protocol over another. Diffserv interaction with tunnels is
   described in [RFC2983], ECN propagation for tunnels is described in
   [RFC6040].

4.4. Decapsulator operation

   A decapsulator performs decapsulation of GUE packets. A decapsulator
   is addressed by the outer destination IP address of a GUE packet. 
   The decapsulator validates packets, including fields of the GUE
   header. If a packet is acceptable, the UDP and GUE headers are
   removed and the packet is resubmitted for IP protocol processing or
   control message processing if it is a control message.

   If a decapsulator receives a GUE packet with an unsupported version,
   unknown flag, bad header length (too small for included optional
   fields), unknown control message type, or an otherwise malformed
   header, it must drop the packet and may log the event. No error
 


Herbert, Yong, Zia       Expires September 2015                 [Page 9]

Internet Draft              herbert-gue.txt                March 6, 2015


   message is returned back to the encapsulator. Note that set flags in
   GUE that are unknown to a decapsulator MUST NOT be ignored. If a GUE
   packet is received by a decapsulator with unknown flags, the packet
   MUST be dropped.

4.5. Router and switch operation

   Routers and switches should forward GUE packets as standard UDP/IP
   packets. The outer five-tuple should contain sufficient information
   to perform flow classification corresponding to the flow of the inner
   packet. A switch should not normally need to parse a GUE header, and
   none of the flags or optional fields in the GUE header should affect
   routing.

   A router should not modify a GUE header when forwarding a packet. It
   may encapsulate a GUE packet in another GUE packet, for instance to
   implement a network tunnel. In this case the router takes the role of
   an encapsulator, and the corresponding decapsulator is the logical
   endpoint of the tunnel.

4.6. Middlebox interactions

   A middle box may interpret some flags and optional fields of the GUE
   header for classification purposes, but is not required to understand
   all flags and fields in GUE packets. A middle box should not drop a
   GUE packet because there are flags unknown to it. The header length
   in the GUE header allows a middlebox to inspect the payload packet
   without needing to parse the flags or optional fields. 

   A middlebox may infer bidirectional connection semantics to a UDP
   flow. For instance a stateful firewall may create a five-tuple rule
   to match flows on egress, and a corresponding five-tuple rule for
   matching ingress packets where the roles of source and destination
   are reversed for the IP addresses and UDP port numbers. To operate in
   this environment, a GUE tunnel must assume connected semantics
   defined by the UDP five tuple and the use of GUE encapsulation must
   be symmetric between both endpoints. The source port set in the UDP
   header must be the destination port the peer would set for replies.

4.7. NAT

   IP address and port translation can be performed on the UDP/IP
   headers adhering to the requirements for NAT with UDP [RFC478]. In
   the case of stateful NAT, connection semantics must be applied to a
   GUE tunnel as described above.

   When using transport mode encapsulation and traversing a NAT, the IP
   addresses may be changed such that the pseudo header checksum used
 


Herbert, Yong, Zia       Expires September 2015                [Page 10]

Internet Draft              herbert-gue.txt                March 6, 2015


   for checksum calculation is modified and the checksum will be found
   invalid at the receiver. To compensate for this, A GUE option can be
   added which contains the checksum over the source and destination
   addresses when the packet is transmitted. Upon receiving this option,
   the delta of the pseudo header checksum is computed by subtracting
   the checksum over the source and and destination addresses from the
   checksum value in the option. The resultant value is then added into
   checksum calculation when validating the inner transport checksum.

4.8. Checksum Handling

   This section describes the requirements around the UDP checksum and
   GUE header checksum. Checksums are an important consideration in that
   that they can provide end to end validation and protect against
   packet mis-delivery. The latter is allowed by the inclusion of a
   pseudo header that covers the IP addresses and UDP ports of the
   encapsulating headers.

4.8.1. Checksum requirements

   The potential for mis-delivery of packets due to corruption of IP,
   UDP, or GUE headers must be considered. One of the following
   requirements must be met:

  o UDP checksums are enabled (for IPv4 or IPv6).

  o The GUE header checksum is used.

  o Zero UDP checksums are used in accordance with applicable
    requirements in [GREUDP], [RFC6935], and [RFC6936].

4.8.2. GUE header checksum

    The GUE header checksum provides a UDP-lite [RFC3828] type of
    checksum capability as an optional field of the GUE header. The GUE
    header checksum minimally covers the GUE header and a GUE pseudo
    header. The GUE pseudo header includes the corresponding IP
    addresses as well as the UDP ports of the encapsulating headers.
    This checksum should provide adequate protection against address
    corruption in IPv6 when the UDP checksum is zero. Additionally, the
    GUE checksum provides protection of the GUE header when the UDP
    checksum is set to zero with either IPv4 or IPv6. The GUE header
    checksum is defined in [GUECSUM].

4.8.3. UDP Checksum with IPv4

    For UDP in IPv4, the UDP checksum MUST be processed as specified in
    [RFC768] and [RFC1122] for both transmit and receive. An
 


Herbert, Yong, Zia       Expires September 2015                [Page 11]

Internet Draft              herbert-gue.txt                March 6, 2015


    encapsulator MAY set the UDP checksum to zero for performance or
    implementation considerations. The IPv4 header includes a checksum
    which protects against mis-delivery of the packet due to corruption
    of IP addresses. The UDP checksum potentially provides protection
    against corruption of the UDP header, GUE header, and GUE payload.
    Enabling or disabling the use of checksums is a deployment
    consideration that should take into account the risk and effects of
    packet corruption, and whether the packets in the network are
    already adequately protected by other, possibly stronger mechanisms
    such as the Ethernet CRC. If an encapsulator sets a zero UDP
    checksum for IPv4 it SHOULD use the GUE header checksum as described
    in section 4.8.2.

    When a decapsulator receives a packet, the UDP checksum field MUST
    be processed. If the UDP checksum is non-zero, the decapsulator MUST
    verify the checksum before accepting the packet. By default a
    decapsulator SHOULD accept UDP packets with a zero checksum. A node
    MAY be configured to disallow zero checksums per [RFC1122]; this may
    be done selectively, for instance disallowing zero checksums from
    certain hosts that are known to be sending over paths subject to
    packet corruption. If verification of a non-zero checksum fails, a
    decapsulator lacks the capability to verify a non-zero checksum, or
    a packet with a zero-checksum was received and the decapsulator is
    configured to disallow, the packet MUST be dropped and an event MAY
    be logged.

4.8.4. UDP Checksum with IPv6

    For UDP in IPv6, the UDP checksum MUST be processed as specified in
    [RFC768] and [RFC2460] for both transmit and receive. Unlike IPv4,
    there is no header checksum in IPv6 that protects against mis-
    delivery due to address corruption. Therefore, when GUE is used over
    IPv6, either the UDP checksum must be enabled or the GUE header
    checksum must be used. An encapsulator MAY set a zero UDP checksum
    for performance or implementation reasons, in which case the GUE
    header checksum MUST be used or applicable requirements for using
    zero UDP checksums in [GREUDP] MUST be met. If the UDP checksum is
    enabled, then the GUE header checksum should not be used since it is
    mostly redundant.

    When a decapsulator receives a packet, the UDP checksum field MUST
    be processed. If the UDP checksum is non-zero, the decapsulator MUST
    verify the checksum before accepting the packet. By default a
    decapsulator MUST only accept UDP packets with a zero checksum if
    the GUE header checksum is used and is verified. If verification of
    a non-zero checksum fails, a decapsulator lacks the capability to
    verify a non-zero checksum, or a packet with a zero-checksum and no
    GUE header checksum was received, the packet MUST be dropped and an
 


Herbert, Yong, Zia       Expires September 2015                [Page 12]

Internet Draft              herbert-gue.txt                March 6, 2015


    event MAY be logged.

4.9. MTU and fragmentation issues

    Standard conventions for handling of MTU (Maximum Transmission Unit)
    and fragmentation in conjunction with networking tunnels
    (encapsulation of layer 2 or layer 3 packets) should be followed.
    Details are described in MTU and Fragmentation Issues with In-the-
    Network Tunneling [RFC4459]

    If a packet is fragmented before encapsulation in GUE, all the
    related fragments must be encapsulated using the same source port
    (inner flow identifier). An operator may set MTU to account for
    encapsulation overhead and reduce the likelihood of fragmentation.

4.10 Congestion control

    Per requirements of [RFC5405], if the IP traffic encapsulated with
    GUE implements proper congestion control no additional mechanisms
    should be required.

    In the case that the encapsulated traffic does not implement any or
    sufficient control, or it is not known rather a transmitter will
    consistently implement proper congestion control, then congestion
    control at the encapsulation layer must be provided. Note this case
    applies to a significant use case in network virtualization in which
    guests run third party networking stacks that cannot be implicitly
    trusted to implement conformant congestion control.

    Out of band mechanisms such as rate limiting, Managed Circuit
    Breaker, or traffic isolation may used to provide rudimentary
    congestion control. For finer grained congestion control that allow
    alternate congestion control algorithms, reaction time within an
    RTT, and interaction with ECN, in band mechanisms may warranted.

    DCCP may be used to provide congestion control for encapsulated
    flows. In this case, the protocol stack for an IP tunnel may be IP-
    GUE-DCCP-IP. Alternatively, GUE can be extended to include
    congestion control (related data carried in GUE optional fields).
    Congestion control mechanisms for GUE will be elaborated in other
    specifications.

5. Inner flow identifier properties

5.1. Flow classification

    A major objective of using GUE is that a network device can perform
    flow classification corresponding to the flow of the inner
 


Herbert, Yong, Zia       Expires September 2015                [Page 13]

Internet Draft              herbert-gue.txt                March 6, 2015


    encapsulated packet based on the contents in the outer headers.

    Hardware devices commonly perform hash computations on packet
    headers to classify packets into flows or flow buckets. Flow
    classification is done to support load balancing (statistical
    multiplexing) of flows across a set of networking resources.
    Examples of such load balancing techniques are Equal Cost Multipath
    routing (ECMP), port selection in Link Aggregation, and NIC device
    Receive Side Scaling (RSS).  Hashes are usually either a three-tuple
    hash of IP protocol, source address, and destination address; or a
    five-tuple hash consisting of IP protocol, source address,
    destination address, source port, and destination port. Typically,
    networking hardware will compute five-tuple hashes for TCP and UDP,
    but only three-tuple hashes for other IP protocols. Since the five-
    tuple hash provides more granularity, load balancing can be finer
    grained with better distribution. When a packet is encapsulated with
    GUE, the source port in the outer UDP packet is set to reflect the
    flow of the inner packet. When a device computes a five-tuple hash
    on the outer UDP/IP header of a GUE packet, the resultant value
    classifies the packet per its inner flow.

    To support flow classification, the source port of the UDP header in
    GUE is set to a value that maps to the inner flow. This is referred
    to as the inner flow identifier. The inner flow identifier is set by
    the encapsulator; it can be computed on the fly based on packet
    contents or retrieved from a state maintained for the inner flow.

    Examples of deriving an inner flow identifier are:

      o If the encapsulated packet is a layer 4 packet, TCP/IPv4 for
        instance, the inner flow identifier could be based on the
        canonical five-tuple hash of the inner packet.

      o If the encapsulated packet is an AH transport mode packet with
        TCP as next header, the inner flow identifier could be a hash
        over a three-tuple: TCP protocol and TCP ports of the
        encapsulated packet.

      o If a node is encrypting a packet using ESP tunnel mode and GUE
        encapsulation, the inner flow identifier could be based on the
        contents of clear-text packet. For instance, a canonical five-
        tuple hash for a TCP/IP packet could be used.

5.2. Inner flow identifier properties

        The inner flow identifier is the value set in the UDP source
        port of a GUE packet. The inner flow identifier should adhere to
        the following properties:
 


Herbert, Yong, Zia       Expires September 2015                [Page 14]

Internet Draft              herbert-gue.txt                March 6, 2015


      o The value set in the source port should be within the ephemeral
        port range. IANA suggests this range to be 49152 to 65535, where
        the high order two bits of the port are set to one. This
        provides fourteen bits of entropy for the inner flow identifier.

      o The inner flow identifier should have a uniform distribution
        across encapsulated flows.

      o An encapsulator may occasionally change the inner flow
        identifier used for an inner flow per its discretion (for
        security, route selection, etc). Changing the value should
        happen no more than once every thirty seconds.

      o Decapsulators, or any networking devices, should not attempt any
        interpretation of the inner flow identifier, nor should they
        attempt to reproduce any hash calculation. They may use the
        value to match further receive packets for steering decisions,
        but cannot assume that the hash uniquely or permanently
        identifies a flow. 

      o Input to the inner flow identifier is not restricted to ports
        and addresses; input could include flow label from an IPv6
        packet, SPI from an ESP packet, or other flow related state in
        the encapsulator that is not necessarily conveyed in the packet.

      o The assignment function for inner flow identifiers should be
        randomly seeded to mitigate denial of service attacks. The seed
        may be changed periodically.

6. Motivation for GUE

   This section presents the motivation for GUE with respect to other
   encapsulation methods.

   A number of different encapsulation techniques have been proposed for
   the encapsulation of one protocol over another. EtherIP [RFC3378]
   provides layer 2 tunneling of Ethernet frames over IP. GRE [RFC2784],
   MPLS [RFC4023], and L2TP [RFC2661] provide methods for tunneling
   layer 2 and layer 3 packets over IP. NVGRE [NVGRE] and VXLAN
   [RFC7348] are proposals for encapsulation of layer 2 packets for
   network virtualization. IPIP [RFC2003] and Generic packet tunneling
   in IPv6 [RFC2473] provide methods for tunneling IP packets over IP. 

   Several proposals exist for encapsulating packets over UDP including
   ESP over UDP [RFC3948], TCP directly over UDP [TCPUDP], VXLAN, LISP
   [RFC6830] which encapsulates layer 3 packets, and Generic UDP
   Encapsulation for IP Tunneling (GRE over UDP)[GREUDP]. Generic UDP
   tunneling [GUT] is a proposal similar to GUE in that it aims to
 


Herbert, Yong, Zia       Expires September 2015                [Page 15]

Internet Draft              herbert-gue.txt                March 6, 2015


   tunnel packets of IP protocols over UDP.

   GUE has the following discriminating features:

      o UDP encapsulation leverages specialized network device
        processing for efficient transport. The semantics for using the
        UDP source port as an identifier for an inner flow are defined.

      o GUE permits encapsulation of arbitrary IP protocols, which
        includes layer 2 3, and 4 protocols. This potentially allows
        nearly all traffic within a data center to be normalized to be
        either TCP or UDP on the wire.

      o Multiple protocols can be multiplexed over a single UDP port
        number. This is in contrast to techniques to encapsulate
        protocols over UDP using a protocol specific port number (such
        as ESP/UDP, GRE/UDP, SCTP/UDP). GUE provides a uniform and
        extensible mechanism for encapsulating all IP protocols in UDP
        with minimal overhead (four bytes of additional header).

      o GUE is extensible. New flags and optional fields can be defined.

      o The GUE header includes a header length field. This allows a
        network node to inspect an encapsulated packet without needing
        to parse the full encapsulation header.

      o Private data in the encapsulation header allows local
        customization and experimentation while being compatible with
        processing in network nodes (routers and middleboxes).

      o GUE includes both data messages (encapsulation of packets) and
        control messages (such as OAM).

7. Security Considerations

        Encapsulation of IP protocols within GUE should not increase
        security risk, nor provide additional security in itself. As
        suggested in section 5 the source port for of UDP packets in GUE
        should be randomly seeded to mitigate some possible denial
        service attacks.

        GUE is most useful when it is in the outermost header of a
        packet which allows for flow hash calculation as well as making
        GUE header data (such as virtual network identifier) visible to
        switches and middleboxes. GUE must be amenable to encapsulating
        (and being encapsulated within) IPsec. Also, we allow provisions
        to secure the GUE header itself without external protocol.

 


Herbert, Yong, Zia       Expires September 2015                [Page 16]

Internet Draft              herbert-gue.txt                March 6, 2015


        Security for Generic UDP Encapsulation is described in more
        detail in [GUESEC].

7.1. GUE security fields

        Security fields should be used to provide integrity and
        authentication of the GUE header. Security negotiation
        (algorithms, interpretation of security field, key management,
        etc.) is expected to be done out of band between hosts.

7.2. GUE and IPsec

        GUE may be used to encapsulate IPsec packets. This allows the
        benefits of deriving a flow hash for the inner, potentially
        encrypted, packet. In this case the protocol stack may be:

        +-------------------------------+
        |                               |
        |        UDP/IP header          |
        |                               |
        |-------------------------------|
        |                               |
        |         GUE Header            |
        |                               |
        |-------------------------------| 
        |                               |                              
        |     ESP/AH/private security   |
        |                               |
        |-------------------------------| 
        |                               |                              
        |       Encapsulated packet     |
        |                               |
        +-------------------------------+

        Note that IPsec would not cover the GUE header in this case
        (does not authenticate it for instance). GUE security optional
        fields may be used to provide authentication or integrity of the
        GUE header.

8. IANA Consideration

        A user UDP port number assignment for GUE has been assigned:

          Service Name: gue
          Transport Protocol(s): UDP
          Assignee: Tom Herbert <therbert@google.com>
          Contact: Tom Herbert <therbert@google.com>
          Description: Generic UDP Encapsulation
 


Herbert, Yong, Zia       Expires September 2015                [Page 17]

Internet Draft              herbert-gue.txt                March 6, 2015


          Reference: draft-herbert-gue
          Port Number: 6080
          Service Code: N/A
          Known Unauthorized Uses: N/A
          Assignment Notes: N/A

9. Acknowledgements

        The authors would like to thank David Liu for valuable input on
        this draft.

                           

10. References

10.1. Normative References


   [RFC0768] Postel, J., "User Datagram Protocol", STD 6, RFC 768,
   August 1980.

   [RFC2434] Narten, T. and H. Alvestrand, "Guidelines for Writing an
   IANA Considerations Section in RFCs", RFC 2434, October 1998.

   [RFC2983] Black, D., "Differentiated Services and Tunnels", RFC 2983,
   October 2000.

   [RFC6040] Briscoe, B., "Tunnelling of Explicit Congestion
   Notification", RFC 6040, November 2010.

   [RFC6936] Fairhurst, G. and M. Westerlund, "Applicability Statement
   for the Use of IPv6 UDP Datagrams with Zero Checksums", RFC 6936,
   April 2013.

   [RFC4459] Savola, P., "MTU and Fragmentation Issues with In-the-
   Network Tunneling", RFC 4459, April 2006.

10.2. Informative References

   [RFC2003] Perkins, C., "IP Encapsulation within IP", RFC 2003,
   October 1996.

   [RFC3948] Huttunen, A., Swander, B., Volpe, V., DiBurro, L., and M.
   Stenberg, "UDP Encapsulation of IPsec ESP Packets", RFC 3948, January
   2005.

   [RFC6830] Farinacci, D., Fuller, V., Meyer, D., and D. Lewis, "The
   Locator/ID Separation Protocol (LISP)", RFC 6830, January 2013.
 


Herbert, Yong, Zia       Expires September 2015                [Page 18]

Internet Draft              herbert-gue.txt                March 6, 2015


   [RFC3378] Housley, R. and S. Hollenbeck, "EtherIP: Tunneling Ethernet
   Frames in IP Datagrams", RFC 3378, September 2002.

   [RFC2784] Farinacci, D., Li, T., Hanks, S., Meyer, D., and P. Traina,
   Generic Routing Encapsulation (GRE)", RFC 2784, March 2000.

   [RFC4023] Worster, T., Rekhter, Y., and E. Rosen, Ed., "Encapsulating
   MPLS in IP or Generic Routing Encapsulation (GRE)", RFC 4023, March
   2005.

   [RFC2661] Townsley, W., Valencia, A., Rubens, A., Pall, G., Zorn, G.,
   and B. Palter, "Layer Two Tunneling Protocol "L2TP"", RFC 2661,
   August 1999.

   [RFC5925] Touch, J., Mankin, A., and R. Bonica, "The TCP
   Authentication Option", RFC 5925, June 2010.

   [RFC3828] Larzon, L-A., Degermark, M., Pink, S., Jonsson, L-E., Ed.,
   and G. Fairhurst, Ed., "The Lightweight User Datagram Protocol (UDP-
   Lite)", RFC 3828, July 2004, <http://www.rfc-
   editor.org/info/rfc3828>.

   [RFC7348] Mahalingam, M., Dutt, D., Duda, K., Agarwal, P., Kreeger,
   L., Sridhar, T., Bursell, M., and C. Wright, "Virtual eXtensible
   Local Area Network (VXLAN): A Framework for Overlaying Virtualized
   Layer 2 Networks over Layer 3 Networks", RFC 7348, August 2014,
   <http://www.rfc-editor.org/info/rfc7348>.

   [NVGRE] NVGRE: Network Virtualization using Generic Routing
   Encapsulation draft-sridharan-virtualization-nvgre-03

   [TCPUDP] Encapsulation of TCP and other Transport Protocols over UDP
   draft-cheshire-tcp-over-udp-00

   [GREUDP] Generic UDP Encapsulation for IP Tunneling draft-yong-tsvwg-
   gre-in-udp-encap-02

   [GUESEC] Yong, L., Herbert, T., "Generic UDP Encapsulation  (GUE) for
   Secure Transport", draft-hy-gue-4-secure-transport-00, work in
   progress.

   [GUT] Generic UDP Tunnelling (GUT) draft-manner-tsvwg-gut-02.txt

   [REMCSUM] Remote Checksum Offload draft-herbert-remotecsumoffload-00

Appendix A: NIC processing for GUE

   This appendix provides some guidelines for Network Interface Cards
 


Herbert, Yong, Zia       Expires September 2015                [Page 19]

Internet Draft              herbert-gue.txt                March 6, 2015


   (NICs) to implement common offloads and accelerations to support GUE.
   Note that most of this discussion is generally applicable to other
   methods of UDP based encapsulation.

A.1. Receive multi-queue

   Contemporary NICs support multiple receive descriptor queues (multi-
   queue). Multi-queue enables load balancing of network processing for
   a NIC across multiple CPUs. On packet reception, a NIC must select
   the appropriate queue for host processing. Receive Side Scaling is a
   common method which uses the flow hash for a packet to index an
   indirection table where each entry stores a queue number. Flow
   Director and Accelerated Receive Flow Steering (aRFS) allow a host to
   program the queue that is used for a given flow which is identified
   either by an explicit five-tuple or by the flow's hash.

   GUE encapsulation should be compatible with multi-queue NICs that
   support five-tuple hash calculation for UDP/IP packets as input to
   RSS. The inner flow identifier (source port) ensures classification
   of the encapsulated flow even in the case that the outer source and
   destination addresses are the same for all flows (e.g. all flows are
   going over a single tunnel).

   By default, UDP RSS support is often disabled in NICs to avoid out of
   order reception that can occur when UDP packets are fragmented. As
   discussed above, fragmentation of GUE packets should be mitigated by
   fragmenting packets before entering a tunnel, path MTU discovery in
   higher layer protocols, or operator adjusting MTUs. Other UDP traffic
   may not implement such procedures to avoid fragmentation, so enabling
   UDP RSS support in the NIC should be a considered tradeoff during
   configuration.

A.2. Checksum offload

   Many NICs provide capabilities to calculate standard ones complement
   payload checksum for packets in transmit or receive. When using GUE
   encapsulation there are at least two checksums that may be of
   interest: the encapsulated packet's transport checksum, and the UDP
   checksum in the outer header.

A.2.1. Transmit checksum offload

   NICs may provide a protocol agnostic method to offload transmit
   checksum (NETIF_F_HW_CSUM in Linux parlance) that can be used with
   GUE. In this method the host provides checksum related parameters in
   a transmit descriptor for a packet. These parameters include the
   starting offset of data to checksum, the length of data to checksum,
   and the offset in the packet where the computed checksum is to be
 


Herbert, Yong, Zia       Expires September 2015                [Page 20]

Internet Draft              herbert-gue.txt                March 6, 2015


   written. The host initializes the checksum field to pseudo header
   checksum.

   In the case of GUE, the checksum for an encapsulated transport layer
   packet, a TCP packet for instance, can be offloaded by setting the
   appropriate checksum parameters.

   NICs typically can offload only one transmit checksum per packet, so
   simultaneously offloading both an inner transport packet's checksum
   and the outer UDP checksum is likely not possible. In this case
   setting UDP checksum to zero (per above discussion) and offloading
   the inner transport packet checksum might be acceptable.

   If an encapsulator is co-resident with a host, then checksum offload
   may be performed using remote checksum offload [REMCSUM]. Remote
   checksum offload relies on NIC offload of the simple UDP/IP checksum
   which is commonly supported even in legacy devices. In remote
   checksum offload the outer UDP checksum is set and the GUE header
   includes an option indicating the start and offset of the inner
   "offloaded" checksum. The inner checksum is initialized to the pseudo
   header checksum. When a decapsulator receives a GUE packet with the
   remote checksum offload option, it completes the offload operation by
   determining the packet checksum from the indicated start point to the
   end of the packet, and then adds this into the checksum field at the
   offset given in the option. Computing the checksum from the start to
   end of packet is efficient if checksum-complete is provided on the
   receiver.

A.2.2. Receive checksum offload

   GUE is compatible with NICs that perform a protocol agnostic receive
   checksum (CHECKSUM_COMPLETE in Linux parlance). In this technique, a
   NIC computes a ones complement checksum over all (or some predefined
   portion) of a packet. The computed value is provided to the host
   stack in the packet's receive descriptor. The host driver can use
   this checksum to "patch up" and validate any inner packet transport
   checksum, as well as the outer UDP checksum if it is non-zero.

   Many legacy NICs don't provide checksum-complete but instead provide
   an indication that a checksum has been verified (CHECKSUM_UNNECESSARY
   in Linux). Usually, such validation is only done for simple TCP/IP or
   UDP/IP packets. If a NIC indicates that a UDP checksum is valid, the
   checksum-complete value for the UDP packet is the "not" of the pseudo
   header checksum. In this way, checksum-unnecessary can be converted
   to checksum-complete. So if the NIC provides checksum-unnecessary for
   the outer UDP header in an encapsulation, checksum conversion can be
   done so that the checksum-complete value is derived and can be used
   by the stack to validate an checksums in the encapsulated packet.
 


Herbert, Yong, Zia       Expires September 2015                [Page 21]

Internet Draft              herbert-gue.txt                March 6, 2015


A.3. Transmit Segmentation Offload

   Transmit Segmentation Offload (TSO) is a NIC feature where a host
   provides a large (>MTU size) TCP packet to the NIC, which in turn
   splits the packet into separate segments and transmits each one. This
   is useful to reduce CPU load on the host.

   The process of TSO can be generalized as:

      - Split the TCP payload into segments which allow packets with
        size less than or equal to MTU.

      - For each created segment:

        1. Replicate the TCP header and all preceding headers of the
           original packet.

        2. Set payload length fields in any headers to reflect the
           length of the segment.

        3. Set TCP sequence number to correctly reflect the offset of
           the TCP data in the stream.

        4. Recompute and set any checksums that either cover the payload
           of the packet or cover header which was changed by setting a
           payload length.

   Following this general process, TSO can be extended to support TCP
   encapsulation in GUE.  For each segment the Ethernet, outer IP, UDP
   header, GUE header, inner IP header if tunneling, and TCP headers are
   replicated. Any packet length header fields need to be set properly
   (including the length in the outer UDP header), and checksums need to
   be set correctly (including the outer UDP checksum if being used).

   To facilitate TSO with GUE it is recommended that optional fields
   should not contain values that must be updated on a per segment
   basis-- for example the GUE fields should not include checksums,
   lengths, or sequence numbers that refer to the payload. If the GUE
   header does not contain such fields then the TSO engine only needs to
   copy the bits in the GUE header when creating each segment and does
   not need to parse the GUE header. 

A.4. Large Receive Offload

   Large Receive Offload (LRO) is a NIC feature where packets of a TCP
   connection are reassembled, or coalesced, in the NIC and delivered to
   the host as one large packet. This feature can reduce CPU utilization
   in the host.
 


Herbert, Yong, Zia       Expires September 2015                [Page 22]

Internet Draft              herbert-gue.txt                March 6, 2015


   LRO requires significant protocol awareness to be implemented
   correctly and is difficult to generalize. Packets in the same flow
   need to be unambiguously identified. In the presence of tunnels or
   network virtualization, this may require more than a five-tuple match
   (for instance packets for flows in two different virtual networks may
   have identical five-tuples). Additionally, a NIC needs to perform
   validation over packets that are being coalesced, and needs to
   fabricate a single meaningful header from all the coalesced packets.

   The conservative approach to supporting LRO for GUE would be to
   assign packets to the same flow only if they have identical five-
   tuple and were encapsulated the same way. That is the outer IP
   addresses, the outer UDP ports, GUE protocol, GUE flags and fields,
   and inner five tuple are all identical. 

Appendix B: Privileged ports

   Using the source port to contain an inner flow identifier value
   disallows the security method of a receiver enforcing that the source
   port be a privileged port. Privileged ports are defined by some
   operating systems to restrict source port binding. Unix, for
   instance, considered port number less than 1024 to be privileged.

   Enforcing that packets are sent from a privileged port is widely
   considered an inadequate security mechanism and has been mostly
   deprecated. To approximate this behavior, an implementation could
   restrict a user from sending a packet destined to the GUE port
   without proper credentials.

Appendix C: Inner flow identifier as a route selector

   An encapsulator generating an inner flow identifier may modulate the
   value to perform a type of multipath source routing. Assuming that
   networking switches perform ECMP based on the flow hash, a sender can
   affect the path by altering the inner flow identifier.  For instance,
   a host may store a flow hash in its PCB for an inner flow, and may
   alter the value upon detecting that packets are traversing a lossy
   path. Changing the inner flow identifier for a flow should be subject
   to hysteresis (at most once every thirty seconds) to limit the number
   of out of order packets.

Appendix D: Hardware protocol implementation considerations

   A low level protocol, such is GUE, is likely interesting to being
   supported by high speed network devices. Variable length header (VLH)
   protocols like GUE are often considered difficult to efficiently
   implement in hardware. In order to retain the important
   characteristics of an extensible and robust protocol, hardware
 


Herbert, Yong, Zia       Expires September 2015                [Page 23]

Internet Draft              herbert-gue.txt                March 6, 2015


   vendors may practice "constrained flexibility". In this model, only
   certain combinations or protocol header parameterizations are
   implemented in hardware fast path. Each such parameterization is
   fixed length so that the particular instance can be optimized as a
   fixed length protocol. In the case of GUE this constitutes specific
   combinations of GUE flags, fields, and next protocol. The selected
   combinations would naturally be the most common cases which form the
   "fast path", and other combinations are assumed to take the "slow
   path".

   In time, needs and requirements of the protocol may change which may
   manifest themselves as new parameterizations to be supported in the
   fast path. To allow allow this extensibility, a device practicing
   constrained flexibility should allow the fast path parameterizations
   to be programmable.

Authors' Addresses

   Tom Herbert
   Google
   1600 Amphitheatre Parkway
   Mountain View, CA
   US

   EMail: tom@herbertland.com


   Lucy Yong
   Huawei USA
   5340 Legacy Dr.
   Plano, TX  75024
   US

   Osama Zia
   Microsoft
   osamaz@microsoft.com















Herbert, Yong, Zia       Expires September 2015                [Page 24]