Internet DRAFT - draft-iab-smart-object-workshop
draft-iab-smart-object-workshop
Network Working Group H. Tschofenig
Internet-Draft Nokia Siemens Networks
Intended status: Informational J. Arkko
Expires: August 1, 2012 Ericsson
January 29, 2012
Report from the 'Interconnecting Smart Objects with the Internet'
Workshop, 25th March 2011, Prague
draft-iab-smart-object-workshop-10.txt
Abstract
This document provides an overview of a workshop held by the Internet
Architecture Board (IAB) on 'Interconnecting Smart Objects with the
Internet'. The workshop took place in Prague on March, 25th. The
main goal of the workshop was to solicit feedback from the wider
community on their experience with deploying IETF protocols in
constrained environments. This report summarizes the discussions and
lists the conclusions and recommendations to the Internet Engineering
Task Force (IETF) community.
Note that this document is a report on the proceedings of the
workshop. The views and positions documented in this report are
those of the workshop participants and do not necessarily reflect IAB
views and positions.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 1, 2012.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
Tschofenig & Arkko Expires August 1, 2012 [Page 1]
Internet-Draft Smart Object Workshop Report January 2012
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Constrained Nodes and Networks . . . . . . . . . . . . . . . . 5
3. Workshop Structure . . . . . . . . . . . . . . . . . . . . . . 7
3.1. Architecture . . . . . . . . . . . . . . . . . . . . . . . 7
3.1.1. One Internet vs. Islands . . . . . . . . . . . . . . . 7
3.1.2. Domain Specific Stacks and Profiles . . . . . . . . . 8
3.1.3. Which Layer? . . . . . . . . . . . . . . . . . . . . . 10
3.2. Sleeping Nodes . . . . . . . . . . . . . . . . . . . . . . 11
3.3. Security . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.4. Routing . . . . . . . . . . . . . . . . . . . . . . . . . 14
4. Conclusions and Next Steps . . . . . . . . . . . . . . . . . . 17
5. Security Considerations . . . . . . . . . . . . . . . . . . . 21
6. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 22
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 23
8. Informative References . . . . . . . . . . . . . . . . . . . . 24
Appendix A. Program Committee . . . . . . . . . . . . . . . . . . 29
Appendix B. Workshop Materials . . . . . . . . . . . . . . . . . 30
Appendix C. Accepted Position Papers . . . . . . . . . . . . . . 31
Appendix D. Workshop Participants . . . . . . . . . . . . . . . . 36
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 39
Tschofenig & Arkko Expires August 1, 2012 [Page 2]
Internet-Draft Smart Object Workshop Report January 2012
1. Introduction
The Internet Architecture Board (IAB) holds occasional workshops
designed to consider long-term issues and strategies for the
Internet, and to suggest future directions for the Internet
architecture. This long-term planning function of the IAB is
complementary to the ongoing engineering efforts performed by working
groups of the Internet Engineering Task Force (IETF), under the
leadership of the Internet Engineering Steering Group (IESG) and area
directorates.
Today's Internet is experienced by users as a set of applications,
such as email, instant messaging, and services on the Web. While
these applications do not require users to be present at the time of
service execution, in many cases they are. There are also
substantial differences in performance among the various end devices,
but in general end devices participating in the Internet are
considered to have high performance.
There are, however, a large number of deployed embedded devices and
there is substantial value in interconnecting them with the Internet.
The term "Internet of Things" denotes a trend where a large number of
devices employ communication services offered by the Internet
Protocols. Many of these devices are not directly operated by
humans, but exist as components in buildings, vehicles, and the
environment. There is a large variation in the computing power,
available memory, (electrical) power, and communications bandwidth
between different types of devices.
Many of these devices offer a range of new possibilities or provide
additional value for previously unconnected devices. Some devices
have been connected using proprietary communication networks in the
past but are now migrating to the use of the Internet Protocol suite
in order to share the same communication network between all
applications and to enable rich communications services.
Much of this development can simply run on existing Internet
protocols. For instance, home entertainment and monitoring systems
often offer a web interface to the end user. In many cases the new,
constrained environments can benefit from additional protocols and
protocol extensions that help optimize the communications and lower
the computational requirements. Examples of currently ongoing
standardization efforts targeted for these environments include the
"Constrained RESTful Environments (CoRE)", "IPv6 over Low power WPAN
(6LoWPAN)", "Routing Over Low power and Lossy networks (ROLL)", and
the "Light-Weight Implementation Guidance (LWIG)" working groups at
the IETF.
Tschofenig & Arkko Expires August 1, 2012 [Page 3]
Internet-Draft Smart Object Workshop Report January 2012
This workshop explored the experiences of researchers and developers
when considering the characteristics of constrained devices.
Engineers know that many design considerations need to be taken into
account when developing protocols and architecture. Balancing
between the conflicting goals of code size, economic incentives,
power consumption, usability and security is often difficult, as
illustrated by Clark, et al. in "Tussle in Cyberspace: Defining
Tomorrow's Internet" [Tussle].
Participants at the workshop discussed the experience and approaches
taken when designing protocols and architectures for interconnecting
smart objects to the Internet. The scope of the investigations
included constrained nodes as well as constrained networks.
The call for position papers suggested investigating the area of
integration with the Internet in the following categories:
o Scalability
o Power efficiency
o Interworking between different technologies and network domains
o Usability and manageability
o Security and Privacy
The goals of the workshop can be summarized as follows:
As many deployed smart objects demonstrate, running protocols like
the Internet Protocol Version 4 [RFC0791] and Version 6 [RFC2460],
the User Datagram Protocol (UDP) [RFC0768], the Transmission
Control Protocol (TCP) [RFC0793], the Hypertext Transfer Protocol
(HTTP) [RFC2616], etc., on constrained devices is clearly
possible. Still, protocol designers, system architects and
developers have to keep various limitations in mind. The
organizers were interested to discuss the experience with
deploying IETF protocols in different constrained environments.
Furthermore, the organizers were seeking to identify either issues
where current implementers do not yet have solutions or where
researchers predict potential issues.
The workshop served as a venue to identify problems and to
discover common interests that may turn into new work or into
changes in direction of already ongoing work at the IETF and or
the Internet Research Task Force (IRTF).
Tschofenig & Arkko Expires August 1, 2012 [Page 4]
Internet-Draft Smart Object Workshop Report January 2012
2. Constrained Nodes and Networks
The workshop was spurred by the increasing presence of constrained
devices on the network. It is quite natural to ask how these
limitations impact the design of the affected nodes. Note that not
all nodes suffer from the same set of limitations.
Energy constraints:
Since wireless communication can be a large portion of the power-
budget for wireless devices, reducing unnecessary communication
can significantly increase the battery life of a low-end device.
The choice of low-power radio can also significantly impact the
overall energy consumption, as can sleeping periodically, when the
device is not in use. In some cases, these nodes will only wake
periodically to handle needed communications. This constraint is
quite in contrast to the "always on" paradigm found in regular
Internet hosts. Even in the case of non-battery operated devices,
power is a constraint with respect to energy efficiency goals.
Bandwidth constraints:
Various low power radio networks offer only ~100 kbit/s or even
only a few KBits/s, and show high packet loss as well as high link
quality variability. Nodes may be used in usually highly unstable
radio environments. The physical layer packet size may be limited
(~100 bytes).
Memory constraints:
The amount of volatile and persistent storage impacts the program
execution has important implications for the functionality of the
protocol stack. The Arduino UNO board, for example, provides a
developer with 2 KByte RAM and 32 KByte flash memory (without any
extensions, such as microSD cards).
A system designer also needs to consider CPU constraints, which often
relate to energy constraints: a processor with lower performance
consumes less energy. As described later in this document, the
design of the mainboard may allow certain components to be put to
sleep to further lower energy consumption. In general, embedded
systems are often purpose built with only the hardware components
needed for the given task while general purpose personal computers
are less constrained with regard to their mainboard layout and
typically offer a huge number of optional plug-in peripherals to be
connected. A factor that also has to be taken into consideration is
the intended usage environment. For example, a humidity sensor
deployed outside a building may need to deal with temperatures from
Tschofenig & Arkko Expires August 1, 2012 [Page 5]
Internet-Draft Smart Object Workshop Report January 2012
-50 C to +85 C. There are often physical size limitations for smart
objects. While traditional mainboards are rather large, such as the
Advanced Technology eXtended (ATX) design with a board size of 305 x
244 mm available in many PCs or the mini-ITX design typically found
in home theater PCs with 170 x 170 mm, mainboard layouts for embedded
systems are typically much smaller, such as the CoreExpress layout
with 58 x 65 mm, or even smaller. In addition to the plain mainboard
additional sensors, peripherals, a power adapter/battery, and a case
have to be taken into consideration. Finally, there are cost
restrictions as well.
The situation becomes more challenging when not only the hosts are
constrained but also the network nodes themselves.
While there are constantly improvements being made, Moore's law tends
to be less effective in the embedded system space than in personal
computing devices: Gains made available by increases in transistor
count and density are more likely to be invested in reductions of
cost and power requirements than into continual increases in
computing power.
Tschofenig & Arkko Expires August 1, 2012 [Page 6]
Internet-Draft Smart Object Workshop Report January 2012
3. Workshop Structure
With the ongoing work on connecting smart objects to the Internet
there are many challenges the workshop participants raised in more
than 70 accepted position papers. With a single workshop day
discussions had to be focused and priority was given to those topics
that had been raised by many authors. A summary of the identified
issues are captured in the subsections below.
3.1. Architecture
A number of architectural questions were brought up in the workshop.
This is natural, as the architectural choices affect the required
technical solutions and the need for standards. At this workshop
questions regarding the separation of traffic, the need for profiling
for application specific domains, the demand for data model specific
standardization, as well as the design choices of the layer at which
functionality should be put were discussed and are briefly summarized
below.
3.1.1. One Internet vs. Islands
Devices that used to be in proprietary or application-specific
networks are today migrating to IP networks. There is, however, the
question of whether these smart objects are now on the same IP
network as any other application. Controlled applications, like the
fountains in front of the Bellagio hotel in Las Vegas that are
operated as a distributed control system [Dolin], probably are not
exchanging their control messages over the same network that is also
used by hotel guests for their Internet traffic. The same had been
argued for smart grids, which are described as "A smart grid is a
digitally enabled electrical grid that gathers, distributes, and acts
on information about the behavior of all participants (suppliers and
consumers) in order to improve the efficiency, reliability,
economics, and sustainability of electricity services." [SmartGrid].
The question that was raised during the workshop is therefore in what
sense are we talking about one Internet or about using IP technology
for a separate, walled garden network that is independent of the
Internet?
Cullen Jennings compared the current state of smart object deployment
with the evolution of voice-over-IP: "Initially, many vendors
recommended to run VoIP over a separate VLAN or a separate
infrastructure. Nobody could imagine how to make the type of real-
time guarantees, how to debug it, and how to get it to work because
the Internet is not ideally suited for making any types of guarantees
for real-time systems. As time went on people got better at making
voice work across that type of IP network. They suddenly noticed
Tschofenig & Arkko Expires August 1, 2012 [Page 7]
Internet-Draft Smart Object Workshop Report January 2012
that having voice running on a separate virtual network than their
other applications was a disaster. They couldn't decide if a PC was
running a softphone and whether it went on a voice or a data network.
At that point people realized that they needed a converged network
and all moved to one. I wouldn't be surprised to see the same
happens here. Initially, we will see very separated networks. Then,
those will be running over the same hardware to take advantage of the
cost benefits of not having to deploy multiple sets of wires around
buildings. Over time there will be strong needs to directly
communicate with each other. We need to be designing the system for
the long run. Assume everything will end up on the same network even
if you initially plan to run it in separate networks."
It is clearly possible to let sensors in a building communicate
through the wireless access points and through the same
infrastructure used for Internet access, if you want to. Those who
want separation at the physical layer can do so as well. What is
important is to make sure that these different deployment
philosophies do not force loss of interoperability.
The level of interoperability that IP accomplished fostered
innovation at the application layer. Ralph Droms reinforced this
message by saying: "Bright people will take a phone, build an
application and connect it, with the appropriate security controls in
place, to the things in my house in ways we have never thought about
before. Otherwise we are just building another telephone network."
3.1.2. Domain Specific Stacks and Profiles
Imagine a building network scenario where a new light bulb is
installed that should, out of the box without further configuration,
interoperate with the already present light switch from a different
vendor in the room. For many this is the desired level of
interoperability in the area of smart object design. To accomplish
this level of interoperability it is not sufficient to provide
interoperability only at the network layer. Even running the same
transport protocol and application layer protocol (e.g., HTTP) is
insufficient since both devices need to understand the semantics of
the payloads for "Turn the light on" as well.
Standardizing the entire protocol stack for this specific "light
switch/light bulb" scenario is possible. A possible stack would, for
example, use IPv6 with a specific address configuration mechanism
(such as stateless address autoconfiguration), a network access
authentication security mechanism such as Protocol for carrying
Authentication for Network Access (PANA) [RFC5191], a service
discovery mechanism (e.g., multicast DNS with DNS-SD
[I-D.cheshire-dnsext-dns-sd]), an application layer protocol, for
Tschofenig & Arkko Expires August 1, 2012 [Page 8]
Internet-Draft Smart Object Workshop Report January 2012
example, Constrained Application Protocol (CoAP) [I-D.ietf-core-coap]
(which uses UDP), and the syntax and semantic for the light on/off
functionality.
As this list shows there is already some amount of protocol
functionality that has to be agreed on by various stakeholders to
make this scenario work seamlessly. As we approach more complex
protocol interactions the functionality quickly becomes more complex:
IPv4 and IPv6 on the network layer, various options at the transport
layer (such as UDP, TCP, the Stream Control Transmission Protocol
(SCTP) [RFC4960], and the Datagram Congestion Control Protocol (DCCP)
[RFC4340]), and there are plenty of choices at the application layer
with respect to communication protocols, data formats and data
models. Different requirements have led to the development of a
variety of communication protocols: client-server protocols in the
style of the original HTTP, publish-subscribe protocols (like Session
Initiation Protocol (SIP) [RFC3261] or Extensible Messaging and
Presence Protocol (XMPP) [RFC3921]), store-and-forward messaging
(borrowed from the delay tolerant networking community). Along with
the different application layer communication protocols come various
identity and security mechanisms.
With the smart object constraints it feels natural to develop these
stacks since each application domain (e.g., health-care, smart grids,
building networking) will have their unique requirements and their
own community involved in the design process. How likely are these
profiles going to be the right match for the future, specifically for
the new innovations that will come? How many of these stacks are we
going to have? Will the differences in the profiles purely be the
result of different requirements coming from the individual
application domains or will these mismatches reflect the spirit,
understanding and preferences of the community designing them? How
many stacks will multi-purpose devices have to implement?
Standardizing profiles independently for each application is not the
only option. Another option is to let many different applications
utilize a common foundation, i.e., a protocol stack that is
implemented and utilized by every device. This, however, requires
various application domains to be analyzed for their common
characteristics and to identify requirements that are common across
all of them. The level of difficulty for finding an agreement of how
such a foundation stack should look depends on how many layers it
covers and how lightweight it has to be.
From the discussions at the workshop it was clear that the available
options are not ideal and further discussions are needed.
Tschofenig & Arkko Expires August 1, 2012 [Page 9]
Internet-Draft Smart Object Workshop Report January 2012
3.1.3. Which Layer?
The end-to-end principle states that functionality should be put into
the end points instead of into the networks. An additional
recommendation, which is equally important, is to put functionality
higher up in the protocol stack. While it is useful to make common
functionality available as building blocks to higher layers the wide
range of requirements by different applications led to a model where
lower layers provide only very basic functionality and more
sophisticated features were made available by various applications.
Still, there has been the desire to put application layer
functionality into the lower layers of the networking stack. A
common belief is that performance benefits can be gained if
functionality is placed at the lower layers of the protocol stack.
This new functionality may be offered in the form of a gateway, which
bridges different communication technologies, acts on behalf of other
nodes, and offers more generic functionality (such as name-based
routing and caching).
Two examples of functionality offered at the network layer discussed
during the workshops were location and name-based routing:
Location:
The notion of location gives each network node the understanding
of proximity (e.g., 'I am a light bulb and in the same room as the
light switch.'). Today, a router may provide information as to
whether other nodes belong to the same subnet or they may provide
location information (for example, in the form of GPS based
coordinates). However, providing a sense of the specific
environment (e.g., a room, building, campus, etc.) is not possible
without manual configuration. While it has been a desirable
feature for many ubiquitous computing applications to know this
type of information and to use it for richer application layer
interactions, widespread deployment has not happened yet.
Name-based Routing:
With the work on recent clean slate architecture proposals, such
as named data networking, flexible naming concepts are being
researched to allow application developers to express their
application layer concepts in a way that they can be used natively
by the underlying networking stack without translation. For
example, Jeff Burke provided the example of his work in a theater
with a distributed control system of technical equipment (such as
projectors, dimmers, and light systems). Application developers
name their equipment with human readable identifiers, which may
Tschofenig & Arkko Expires August 1, 2012 [Page 10]
Internet-Draft Smart Object Workshop Report January 2012
change after the end of a rehearsal, and address them using these
names. These variable length based naming concepts raise
questions regarding scalability.
The workshop participants were not able to come to an agreement about
what functionality should be moved from the application layer to the
network layer.
3.2. Sleeping Nodes
One limitation of smart objects is their available energy. To extend
battery life, for example of a watch battery or single AAA battery
for months, these low power devices have to sleep 99% to 99.5% of
their time. For example, a light sensor may only wake up to check
whether it is night-time to turn on light bulbs. Most parts of the
system, particularly communication components, are put into a
sleeping state (e.g., WLAN radio interface) and selected components,
such as sensors, periodically check for relevant events and, if
necessary, turn on other hardware modules. Every bit is precious, as
is every round trip, and every millisecond of radio activity.
Many IETF protocols are implicitly designed to be always-on, i.e.,
the protocol implementation waits for and reacts to incoming
messages, and may maintain session state (at various layers of the
stack). These protocols work well when energy consumption is not a
concern and where receiving and sending messages happens at a low
cost. It should be understood that energy is consumed both in
transmitting messages (and often more importantly) in keeping the
receiver awake. Allowing devices to sleep most of the time preserves
energy but creates challenges for protocol designs.
The inherent issue encountered by a stationary node resuming from
sleep is that another node may have chosen the same address while the
node was asleep. A number of steps have to be taken before sending a
packet. A new address may have to be obtained, for example using the
Dynamic Host Configuration Protocol (DHCP) or stateless address
autoconfiguration. Optionally, Detecting Network Attachment (DNA)
procedures (see [RFC4436] and [RFC6059]) can be used to shorten the
setup time by noticing that the node is using the same default
gateway.
The issue with a mobile node that is sleeping is that the node may
have been moved to another network (e.g., a sleeping laptop being
transported to a new environment) where on resumption it may discover
that its address has become invalid.
The following design considerations should be taken into account when
energy efficiency is a concern:
Tschofenig & Arkko Expires August 1, 2012 [Page 11]
Internet-Draft Smart Object Workshop Report January 2012
1. Rethink the Always-On Assumption
When designing a protocol that assumes that the nodes are always
on, alternatives need to be considered. This could involve
eliminating functionality (e.g., not implementing DNA or
duplicate address detection) or considering the use of a sleep
proxy. While sleep proxies (e.g., proxZzzy [proxZzzy]) enable
periodic messages to be sent on behalf of sleeping nodes, this
approach assumes that that energy management constraints do not
apply to the sleep proxy, which may not always be the case (e.g.,
if the entire network is deployed in the field without access to
power). Yet another option is for devices to explicitly
communicate sleep cycles so that they can only check for messages
periodically (be it measured in msec, sec, or hours). This is
the approach taken in IEEE 802.11, which supports multiple energy
conservation mechanisms designed to enable a station to spend a
large fraction of the time sleeping.
2. Reduce Network Attachment Costs
As noted above, the procedures for obtaining an address and
assuring its uniqueness can be costly. In a network where nodes
spend a large fraction of the time sleeping, but are not
necessarily mobile, are all of these procedures really necessary?
Can we find ways to reduce the number of protocol interactions
without sacrificing correctness? The main focus of past
investigations has been on IPv6 and neighbor discovery but other
protocols do also deserve a deeper investigation, such as DNS,
and DHCP.
3. Avoid Verbose Protocols
Protocols involving multiple roundtrips and/or lengthy messages
with verbose encodings (e.g., XML) are not always well suited for
constrained environments. Low-power nodes utilizing verbose
protocols have to use more energy in sending messages and have to
stay powered on for a longer period of time as they wait for the
multi-roundtrip protocol exchanges to complete.
The best way to address these problems is to ensure that the
simplest possible protocol exchanges are used when the protocols
in question are designed. In some cases alternative encoding
formats and compression may also help.
4. Think about System-Wide Efficiency
While energy efficiency is critical for low-power devices running
Tschofenig & Arkko Expires August 1, 2012 [Page 12]
Internet-Draft Smart Object Workshop Report January 2012
on batteries, it is also beneficial for other devices as well,
including notebooks, desktops and smartphones. However, if the
goal is energy efficiency as opposed to battery life extension
for low-power devices, then it is important to consider the total
energy consumption of all the elements of the system.
For example, consider energy consumption in a home environment.
In these scenarios it is important to evaluate the energy usage
of the entire system. A light bulb utilizing Internet technology
described in this document may use less power but there is also
the device that controls the bulb that may consume a lot of
energy. If the goal is to reduce overall energy usage, then it
is important to consider these two devices (and potentially many
others) together.
3.3. Security
In the development of smart object applications, as with any other
protocol application solution, security has to be considered early in
the design process. As such, the recommendations currently provided
to IETF protocol architects, such as RFC 3552 [RFC3552], and RFC 4101
[RFC4101], apply also to the smart object space.
While there are additional constraints, as described in Section 2,
security has to be a mandatory part of the solution. The hope is
that this will lead to implementations that provide security
features, deployments that utilize these, and finally that this leads
to use of better security mechanisms. It is important to point out
that the lack of direct user interaction will place hard requirements
on deployment models, configuration mechanisms, and software upgrade/
crypto agility mechanisms.
Since many of the security mechanisms allow for customization,
particularly with regard to the cryptographic primitives utilized,
many believe that IETF security solutions are usable without
modifications in a large part of the smart object domain. Others
call for new work on cryptographic primitives that make use of a
single primitive (such as the Advanced Encryption Standard (AES)
[AES]) as a building block for all cryptographic functions with the
benefit of a smaller footprint of the overall solution, specifically
with respect to hardware limitations (e.g., the hardware architecture
of certain embedded devices prevents pipelining from being used). In
the excitement for new work on optimizations of cryptograhpic
primitives other factors have to be taken into consideration that
influence successful deployment, such as widespread support in
libraries, as well as intellectual property rights (IPR). As an
example of the latter aspect, the struggle of Elliptic Curve
Cryptography (ECC)-based cryptographic algorithms [ECC] to find
Tschofenig & Arkko Expires August 1, 2012 [Page 13]
Internet-Draft Smart Object Workshop Report January 2012
deployment can partially be attributed to its IPR situation. The
reuse of libraries providing cryptographic functions is clearly an
important way to use available memory resources in a more efficient
way. To deal with the performance and footprint concerns
investigations into offloading certain resource-hungry functions to
parties that possess more cryptographic power have been considered.
For example, the ability to delegate certificate validation to
servers has been standardized in the IETF before; for the support of
the Online Certificate Status Protocol (OCSP) in the Internet Key
Exchange protocol version 2 (IKEv2) and in Transport Layer Security
(TLS), see [RFC4806] and [RFC3546], respectively.
Focusing only on the cryptographic primitives would be shortsighted;
many would argue that this is the easy part of a smart object
security solution. Key management and credential enrollment,
however, are considered a big challenge by many particularly when
usability requirements have to be taken into account. Another group
of challenges concern privacy; with smart grids, for example, some
have voiced concerns regarding the ability of third parties to keep
track of an individual's energy consumption (and draw associated
conclusions). As another example, it is easy to see how a scale that
is connected to the Internet for uploading weight information to a
social network could lead to privacy concerns. While security
mechanisms used to offer protection of the communication between
different parties also provide a certain degree of privacy protection
they are clearly not enough to address all concerns. Even with the
best communication security and access control mechanisms in place
one still needs additional safeguards against the concerns mentioned
in the examples.
While a lot can be said about how desirable it would be to deploy
more security protocols on the entire Internet, practical
considerations regarding usability and the incentives of the
stakeholders involved have often lead to slower adoption.
3.4. Routing
A smart object network environment may also employ routers under
similar constraints as the end devices. Currently two approaches to
routing in these low power and lossy networks are under
consideration, namely mesh-under and route-over. The so-called mesh-
under approach places routing functions at the link layer and
consequently all devices appear as immediate neighbors at the network
layer. With the route-over approach routing is done at the IP layer
and none in the link layer. Each physical hop appears as a single IP
hop (ignoring devices that just extend the physical range of
signaling, such as repeaters). Routing in this context means running
a routing protocol. IPv6 Routing Protocol for Low power and Lossy
Tschofenig & Arkko Expires August 1, 2012 [Page 14]
Internet-Draft Smart Object Workshop Report January 2012
Networks (RPL) [I-D.ietf-roll-rpl], for example, belongs to the
route-over category.
From an architectural point of view there are several questions that
arise from where routing is provided, for example:
o Protocols often assume that link characteristics are predictable
when communicating with any device attached to the same link.
Latency, throughput, and reliability may vary considerably between
different devices that are multiple link layer hops away. What
timeout should be used? What happens if a device is unreachable?
In case of default router selection two advertised routers may be
a different number of hops away. Should a device have visibility
into the path to make a decision and what path characteristics
would be useful to have?
o Scoped message delivery to a neighboring IP hop (via link-local
addressing) allows certain types of IP protocols to communicate
with their immediate neighbors and to therefore scope their
recipients. A link-local multicast message will be received by
all nodes in the same IP link local realm unless some special
optimizations are provided by the link layer.
o When path computations are done at the link layer as well as on
the network layer then what coordination needs to take place?
When multiple different link layer technologies are involved in a
network design, routing at layer 3 has to be provided in any case.
[I-D.routing-architecture-iot] talks about these tradeoffs between
route-over and mesh-under in detail. Furthermore, those who decide
about the deployment have to determine how to connect smart objects
to the Internet infrastructure and a number of wired and wireless
technologies may be suitable for a specific deployment. Depending on
the chosen technologies the above-mentioned mesh-under vs. route-over
approach will have to be decided and further decisions will have to
be made about the choice of a specific routing protocol.
In 2008 the IETF formed the Routing Over Low power and Lossy networks
(ROLL) working group to specify a routing solution for smart object
environments. During its first year of existence, the working group
studied routing requirements in detail (see [RFC5867], [RFC5826],
[RFC5673], [RFC5548]), worked on a protocol survey comparing a number
of existing routing protocols, including Ad hoc On-Demand Distance
Vector (AODV)-style of protocols [RFC3561], against the identified
requirements. The protocol survey [I-D.ietf-roll-protocols-survey]
was inconclusive and abandoned without giving rise to publication of
an RFC.
Tschofenig & Arkko Expires August 1, 2012 [Page 15]
Internet-Draft Smart Object Workshop Report January 2012
The ROLL WG concluded that a new routing protocol satisfying the
documented requirements has to be developed and the work on the RPL
was started as the IETF routing protocol for smart object networks.
Nevertheless, controversial discussions at the workshop about which
routing protocols is best in a given environment are still ongoing.
Thomas Clausen, for example, argued for using an AODV-like routing
protocol in [Clausen].
Tschofenig & Arkko Expires August 1, 2012 [Page 16]
Internet-Draft Smart Object Workshop Report January 2012
4. Conclusions and Next Steps
The workshop allowed the participants to get exposed to interesting
applications and their requirements (buildings, fountains, theater,
etc.), to have discussions about radically different architectures
and their issues (e.g., information centric networking), to look at
existing technology from a new angle (sleeping nodes, energy
consumption), to focus on some details of the protocol stack
(neighbor discovery, security, routing) and to learn about
implementation experience.
One goal of the workshop was to identify areas that require further
investigation. The list below reflects the thoughts of the workshop
participants as expressed on the day of the workshop. Note that the
suggested items concern potential work by the IETF and the IRTF and
the order does not imply a particular preference.
Security:
A discussion of security is provided in Section 3.3. In general,
security related protocol exchanges and the required amount of
computational resource requirements can contribute significantly
to the overall processing. Therefore, it remains a challenge to
accomplish performance improvements without sacrificing the
overall security level, taking the usability of the entire system
into consideration.
Another challenge is how to balance the security and performance
needs of smart objects with the interoperability requirements of
hosts on the Internet since different suites of algorithms may
tend to be chosen for these different environments. This involves
trade-offs between performance on the smart objects versus end-to-
end security. Solutions that mandate a "trusted" middlebox whose
only role is to terminate security associations tend to be frowned
upon from the security perspective, especially since end-users of
challenged devices (where those exist) are unlikely to understand
the security consequences of such middleboxes.
The discussion concluded with the following recommendations:
* Investigate usability in cryptographic protocol design with
regard to credential management. As an example, the Bluetooth
pairing mechanism was mentioned as a simple and yet reasonably
secure method of introducing devices into a new environment.
In fact, the IETF working group 'Credential and Provisioning
(ENROLL)' was established years ago to deal with residential
networks but was terminated prematurely due to lack of
progress. The email archive still exists and is available
Tschofenig & Arkko Expires August 1, 2012 [Page 17]
Internet-Draft Smart Object Workshop Report January 2012
[enroll] and may provide useful historical information.
* Standardized authentication and key exchange mechanisms should
be surveyed for suitability in smart object environments with
respect to message size, computational performance, number of
messages, codesize, and main memory requirements. A starting
point of such an investigation (in case of IKEv2) was provided
by Tero Kivinen with [I-D.kivinen-ipsecme-ikev2-minimal] and a
suitable venue for discussion could be the recently established
Light-Weight Implementation Guidance (LWIG) working group
[LWIG].
* Research has to be done in the area of lightweight
cryptographic primitives, namely block ciphers, stream ciphers,
and cryptographic hash functions. Worthwhile to mention is
early work with the National Institute of Standards and
Technology (NIST) new cryptographic hash algorithm 'SHA-3'
competition [SHA3]. A suitable forum for discussion is the
IRTF Crypto Forum Research Group (CFRG) [CFRG].
The difficulty and impact of choosing specialised algorithms for
smart objects should not be underestimated. Issues that arise
include the additional specification complexity (e.g., TLS already
has 100's of ciphersuites defined, most of which are unused in
practice), the long latency in terms of roll out (many hosts are
still using deprecated algorithms 5-10 years after those
algorithms were deprecated) and the barriers that IPR-encumbered
schemes present to widespread deployment. While research on this
topic within CFRG and the cryptographic research community is a
very worthwhile goal, any such algorithms will likely have to
offer very significant benefits before they will be broadly
adopted. 20% less CPU is unlikely to be a winning argument no
matter what an algorithm inventor believes.
Energy Design Considerations:
One part of the workshop was focused on the discussion of energy
implications for IETF protocol design with proposals being made
about how to extend protocols to better support nodes that are
mostly sleeping. Discussion are encouraged to take place at the
RECIPE mailing list [RECIPE]. The workshop position paper
[Wasserman] by Margaret Wasserman provides a good starting point
for further investigations.
Information/Content Centric Networking:
Information/Content Centric Networking is about accessing named
content and a number of research projects have emerged around this
Tschofenig & Arkko Expires August 1, 2012 [Page 18]
Internet-Draft Smart Object Workshop Report January 2012
theme. At this point in time the work is not yet ready for
standardization in the IETF. Instead, the formation of an IRTF
research group has been proposed and more details are available on
the IRTF DISCUSS mailing list [irtf-discuss].
Architectural Guidelines:
Participants suggested developing an architectural write-up about
what can be done with the IETF protocols we have today and how
these different elements may be combined to offer an explanation
for the broader community. This would be a task for the Internet
Architecture Board (IAB). An example of prior work that serves as
input is [RFC6272].
Network Management:
While this topic did not make it onto the workshop agenda it was
considered useful to start a discussion about how to implement
network management protocols, such as Network Configuration
Protocol (NETCONF) [RFC6241], on smart objects. The following
position papers may be useful as a starting point for further
discussions [Ersue], [Schoenwaelde]. An IETF draft is also
available [I-D.hamid-6lowpan-snmp-optimizations].
Congestion Control:
When smart objects transmit sensor readings to some server on the
Internet then these protocol interactions often carry a small
amount of data and happen infrequently, although regularly. With
the work on new application protocols, like the CoAP
[I-D.ietf-core-coap], the question of whether a congestion control
mechanism should be used at the underlying transport protocol or
by the application protocol itself arises.
[I-D.eggert-core-congestion-control] is a starting point for the
CoAP protocol but further work is needed.
Data Models:
Standardization of application layer protocols is important but
does not ensure that, for example, a light switch and a light bulb
are able to interact with each other. One area where participants
saw the need for further work was in the area of data models.
While prior IETF standardization work on, for example, location
[GEOPRIV] can be re-used the question was raised where the IETF
should focus its standardization efforts since domain expertise in
each area will be needed. As a potential example, energy pricing
was discussed, with an example provided by
[I-D.jennings-energy-pricing].
Tschofenig & Arkko Expires August 1, 2012 [Page 19]
Internet-Draft Smart Object Workshop Report January 2012
Discovery:
Additional extensions to developed discovery protocols (such as
mDNS) may be needed for the smart object environment.
Building Networking:
Network architectures in residential as well as commercial
buildings should take the presence of smart objects and dedicated
subnetworks focusing on smart objects into account. A new working
group, Home Networking (HOMENET) [FUN], has been created after the
workshop to look at this topic.
Routing:
Changing radio conditions and link fluctuation may lead to the
need for re-numbering. Workshop participants argued that work
should be started on the multi-link subnetworks to mitigate this
problem, i.e., to extend the notion of a subnet to be able to span
multiple links. With the publication of RFC 4903 [RFC4903] the
Internet Architecture Board had looked into this topic already and
provided pros and cons.
The applicability of specific routing protocols designed for smart
object networks needs further investigation. The ROLL working
group is chartered with the task of constructing an applicability
document for the RPL protocol, for instance.
Tschofenig & Arkko Expires August 1, 2012 [Page 20]
Internet-Draft Smart Object Workshop Report January 2012
5. Security Considerations
The workshop discussions covered a range of potential engineering
activities, each with its own security considerations. As the IETF
community begins to pursue specific avenues arising out of this
workshop, addressing relevant security requirements will be crucial.
As described in this report part of the agenda was focused on the
discussion of security, see Section 3.3.
Tschofenig & Arkko Expires August 1, 2012 [Page 21]
Internet-Draft Smart Object Workshop Report January 2012
6. Acknowledgements
We would like to thank all the participants for their position
papers. The authors of the accepted position papers were invited to
the workshop.
Big thanks to Elwyn Davies for helping us to fix language bugs. We
would also like to thank Andrei Robachevsky, Ulrich Herberg, Thomas
Clausen, Bruce Nordman, Alissa Cooper, Dave Thaler, Bernard Aboba,
and Henning Schulzrinne for their review comments.
Additionally, we would like to thank Ericsson and Nokia Siemens
Networks for their financial support.
Tschofenig & Arkko Expires August 1, 2012 [Page 22]
Internet-Draft Smart Object Workshop Report January 2012
7. IANA Considerations
This document does not require actions by IANA.
Tschofenig & Arkko Expires August 1, 2012 [Page 23]
Internet-Draft Smart Object Workshop Report January 2012
8. Informative References
[AES] "Wikipedia Entry for 'Advanced Encryption Standard'",
http://en.wikipedia.org/wiki/
Advanced_Encryption_Standard , Dec 2011.
[CFRG] McGrew (Chair), D., "IRTF Crypto Forum Research Group
(CFRG)", http://irtf.org/cfrg , June 2011.
[Clausen] Clausen, T. and U. Herberg, "Some Considerations on
Routing in Particular and Lossy Environments", IAB
Interconnecting Smart Objects with the Internet Workshop,
Prague, Czech Republic, http://www.iab.org/wp-content/
IAB-uploads/2011/03/Clausen.pdf, March 2011.
[Dolin] Dolin, B., "Application Communications Requirements for
'The Internet of Things'", IAB Interconnecting Smart
Objects with the Internet Workshop, Prague, Czech Republic
, http://www.iab.org/wp-content/IAB-uploads/2011/03/
Ersue.pdf, March 2011.
[ECC] "Wikipedia Entry for 'Elliptic Curve Cryptography'",
http://en.wikipedia.org/wiki/Elliptic_curve_cryptography ,
Dec 2011.
[Ersue] Ersue, M. and J. Korhonen, "Ersue / Korhonen Smart Object
Workshop Position Paper", IAB Interconnecting Smart
Objects with the Internet Workshop, Prague, Czech Republic
, http://www.iab.org/wp-content/IAB-uploads/2011/03/
Ersue.pdf, March 2011.
[FUN] "FUture home Networking (FUN) Mailing List",
https://www.ietf.org/mailman/listinfo/fun , June 2011.
[GEOPRIV] "IETF Geographic Location/Privacy Working Group",
http://datatracker.ietf.org/wg/geopriv/ , June 2011.
[I-D.cheshire-dnsext-dns-sd]
Cheshire, S. and M. Krochmal, "DNS-Based Service
Discovery", draft-cheshire-dnsext-dns-sd-11 (work in
progress), December 2011.
[I-D.eggert-core-congestion-control]
Eggert, L., "Congestion Control for the Constrained
Application Protocol (CoAP)",
draft-eggert-core-congestion-control-01 (work in
progress), January 2011.
Tschofenig & Arkko Expires August 1, 2012 [Page 24]
Internet-Draft Smart Object Workshop Report January 2012
[I-D.hamid-6lowpan-snmp-optimizations]
Schoenwaelder, J., Mukhtar, H., Joo, S., and K. Kim, "SNMP
Optimizations for Constrained Devices",
draft-hamid-6lowpan-snmp-optimizations-03 (work in
progress), October 2010.
[I-D.ietf-core-coap]
Shelby, Z., Hartke, K., Bormann, C., and B. Frank,
"Constrained Application Protocol (CoAP)",
draft-ietf-core-coap-08 (work in progress), October 2011.
[I-D.ietf-roll-protocols-survey]
Tavakoli, A., Dawson-Haggerty, S., and P. Levis, "Overview
of Existing Routing Protocols for Low Power and Lossy
Networks", draft-ietf-roll-protocols-survey-07 (work in
progress), April 2009.
[I-D.ietf-roll-rpl]
Winter, T., Thubert, P., Brandt, A., Clausen, T., Hui, J.,
Kelsey, R., Levis, P., Pister, K., Struik, R., and J.
Vasseur, "RPL: IPv6 Routing Protocol for Low power and
Lossy Networks", draft-ietf-roll-rpl-19 (work in
progress), March 2011.
[I-D.jennings-energy-pricing]
Jennings, C. and B. Nordman, "Communication of Energy
Price Information", draft-jennings-energy-pricing-01 (work
in progress), July 2011.
[I-D.kivinen-ipsecme-ikev2-minimal]
Kivinen, T., "Minimal IKEv2",
draft-kivinen-ipsecme-ikev2-minimal-00 (work in progress),
February 2011.
[I-D.routing-architecture-iot]
Hui, J. and J. Vasseur, "Routing Architecture in Low-Power
and Lossy Networks (LLNs)",
draft-routing-architecture-iot-00 (work in progress),
March 2011.
[LWIG] "IETF Light-Weight Implementation Guidance (LWIG) Working
Group", http://datatracker.ietf.org/wg/lwig/charter/ ,
June 2011.
[RECIPE] "Reducing Energy Consumption with Internet Protocols
Exploration (RECIPE) Mailing List",
https://www.ietf.org/mailman/listinfo/recipe , June 2011.
Tschofenig & Arkko Expires August 1, 2012 [Page 25]
Internet-Draft Smart Object Workshop Report January 2012
[RFC0768] Postel, J., "User Datagram Protocol", STD 6, RFC 768,
August 1980.
[RFC0791] Postel, J., "Internet Protocol", STD 5, RFC 791,
September 1981.
[RFC0793] Postel, J., "Transmission Control Protocol", STD 7,
RFC 793, September 1981.
[RFC2222] Myers, J., "Simple Authentication and Security Layer
(SASL)", RFC 2222, October 1997.
[RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 2460, December 1998.
[RFC2616] Fielding, R., Gettys, J., Mogul, J., Frystyk, H.,
Masinter, L., Leach, P., and T. Berners-Lee, "Hypertext
Transfer Protocol -- HTTP/1.1", RFC 2616, June 1999.
[RFC2743] Linn, J., "Generic Security Service Application Program
Interface Version 2, Update 1", RFC 2743, January 2000.
[RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
A., Peterson, J., Sparks, R., Handley, M., and E.
Schooler, "SIP: Session Initiation Protocol", RFC 3261,
June 2002.
[RFC3546] Blake-Wilson, S., Nystrom, M., Hopwood, D., Mikkelsen, J.,
and T. Wright, "Transport Layer Security (TLS)
Extensions", RFC 3546, June 2003.
[RFC3552] Rescorla, E. and B. Korver, "Guidelines for Writing RFC
Text on Security Considerations", BCP 72, RFC 3552,
July 2003.
[RFC3561] Perkins, C., Belding-Royer, E., and S. Das, "Ad hoc On-
Demand Distance Vector (AODV) Routing", RFC 3561,
July 2003.
[RFC3748] Aboba, B., Blunk, L., Vollbrecht, J., Carlson, J., and H.
Levkowetz, "Extensible Authentication Protocol (EAP)",
RFC 3748, June 2004.
[RFC3921] Saint-Andre, P., Ed., "Extensible Messaging and Presence
Protocol (XMPP): Instant Messaging and Presence",
RFC 3921, October 2004.
[RFC4101] Rescorla, E. and IAB, "Writing Protocol Models", RFC 4101,
Tschofenig & Arkko Expires August 1, 2012 [Page 26]
Internet-Draft Smart Object Workshop Report January 2012
June 2005.
[RFC4340] Kohler, E., Handley, M., and S. Floyd, "Datagram
Congestion Control Protocol (DCCP)", RFC 4340, March 2006.
[RFC4436] Aboba, B., Carlson, J., and S. Cheshire, "Detecting
Network Attachment in IPv4 (DNAv4)", RFC 4436, March 2006.
[RFC4806] Myers, M. and H. Tschofenig, "Online Certificate Status
Protocol (OCSP) Extensions to IKEv2", RFC 4806,
February 2007.
[RFC4903] Thaler, D., "Multi-Link Subnet Issues", RFC 4903,
June 2007.
[RFC4960] Stewart, R., "Stream Control Transmission Protocol",
RFC 4960, September 2007.
[RFC5191] Forsberg, D., Ohba, Y., Patil, B., Tschofenig, H., and A.
Yegin, "Protocol for Carrying Authentication for Network
Access (PANA)", RFC 5191, May 2008.
[RFC5548] Dohler, M., Watteyne, T., Winter, T., and D. Barthel,
"Routing Requirements for Urban Low-Power and Lossy
Networks", RFC 5548, May 2009.
[RFC5582] Schulzrinne, H., "Location-to-URL Mapping Architecture and
Framework", RFC 5582, September 2009.
[RFC5673] Pister, K., Thubert, P., Dwars, S., and T. Phinney,
"Industrial Routing Requirements in Low-Power and Lossy
Networks", RFC 5673, October 2009.
[RFC5826] Brandt, A., Buron, J., and G. Porcu, "Home Automation
Routing Requirements in Low-Power and Lossy Networks",
RFC 5826, April 2010.
[RFC5867] Martocci, J., De Mil, P., Riou, N., and W. Vermeylen,
"Building Automation Routing Requirements in Low-Power and
Lossy Networks", RFC 5867, June 2010.
[RFC6059] Krishnan, S. and G. Daley, "Simple Procedures for
Detecting Network Attachment in IPv6", RFC 6059,
November 2010.
[RFC6241] Enns, R., Bjorklund, M., Schoenwaelder, J., and A.
Bierman, "Network Configuration Protocol (NETCONF)",
RFC 6241, June 2011.
Tschofenig & Arkko Expires August 1, 2012 [Page 27]
Internet-Draft Smart Object Workshop Report January 2012
[RFC6272] Baker, F. and D. Meyer, "Internet Protocols for the Smart
Grid", RFC 6272, June 2011.
[SHA3] "NIST Cryptographic Hash Algorithm Competition",
http://csrc.nist.gov/groups/ST/hash/sha-3/index.html ,
Dec 2011.
[Schoenwaelde]
Schoenwaelde, J., Tsou, T., and B. Sarikaya, "Protocol
Profiles for Constrained Devices", IAB Interconnecting
Smart Objects with the Internet Workshop, Prague, Czech Re
public, http://www.iab.org/wp-content/IAB-uploads/2011/03/
Schoenwaelder.pdf, March 2011.
[SmartGrid]
"Wikipedia Entry for 'Smart Grid'",
http://en.wikipedia.org/wiki/Smart_grid , Dec 2011.
[Tussle] Clark, D., Wroslawski, J., Sollins, K., and R. Braden,
"Tussle in Cyberspace: Defining Tomorrow's Internet", In
Proc. ACM SIGCOMM ,
http://www.acm.org/sigcomm/sigcomm2002/papers/tussle.html,
2002.
[Wasserman]
Wasserman, M., "It's Not Easy Being "Green"", IAB
Interconnecting Smart Objects with the Internet Workshop,
Prague, Czech Republic, http://www.iab.org/wp-content/
IAB-uploads/2011/03/Wasserman.pdf, March 2011.
[enroll] "IETF Credential and Provisioning Working Group Mailing
List", http://mailman.mit.edu/pipermail/ietf-enroll/ ,
June 2011.
[irtf-discuss]
"Draft ICN RG Charter on IRTF DISCUSS Mailing List", http:
//www.ietf.org/mail-archive/web/irtf-discuss/current/
msg00041.html , May 2011.
[proxZzzy]
ECMA, "proxZZZyTM for sleeping hosts, ECMA-393", http://
www.ecma-international.org/publications/standards/
Ecma-393.htm , Feb 2010.
Tschofenig & Arkko Expires August 1, 2012 [Page 28]
Internet-Draft Smart Object Workshop Report January 2012
Appendix A. Program Committee
The following persons are responsible for the organization of the
associated workshop and are responsible also for this event: Jari
Arkko, Hannes Tschofenig, Bernard Aboba, Carsten Bormann, David
Culler, Lars Eggert, JP Vasseur, Stewart Bryant, Adrian Farrel, Ralph
Droms, Geoffrey Mulligan, Alexey Melnikov, Peter Saint-Andre, Marcelo
Bagnulo, Zach Shelby, Isidro Ballesteros Laso, Fred Baker, Cullen
Jennings, Manfred Hauswirth, and Lukas Kencl.
Tschofenig & Arkko Expires August 1, 2012 [Page 29]
Internet-Draft Smart Object Workshop Report January 2012
Appendix B. Workshop Materials
Information about the workshop can be found at the IAB webpage:
http://www.iab.org/about/workshops/smartobjects/
The position papers can be retrieved from:
http://www.iab.org/about/workshops/smartobjects/papers/
The slides are available for download at the following webpage:
http://www.iab.org/about/workshops/smartobjects/agenda.html
Detailed meeting minutes are published here:
http://www.iab.org/about/workshops/smartobjects/minutes.html
Tschofenig & Arkko Expires August 1, 2012 [Page 30]
Internet-Draft Smart Object Workshop Report January 2012
Appendix C. Accepted Position Papers
1. Deployment Experience with Low Power Lossy Wireless Sensor
Networks by C. Adjih, E. Baccelli, P. Jacquet, P. Minet, M.
Philipp, and G. Wittenburg
2. CoAP improvements to meet embedded device hardware constraints
by Davide Barbieri
3. Unified Device Networking Protocols for Smart Objects by Daniel
Barisic and Anton Pfefferseder
4. Simplified neighbour cache implementation in RPL/6LoWPAN by
Dominique Barthel
5. Home Control in a consumer's perspective by Anders Brandt
6. Authoring Place-based Experiences with an Internet of Things:
Tussles of Expressive, Operational, and Participatory Goals by
Jeff Burke
7. A Dynamic Distributed Federated Approach for the Internet of
Things by Diego Casado Mansilla, Juan Ramon Velasco Perez, and
Mario Lopez-Ramos
8. Quickly interoperable Internet of Things using simple
transparent gateways by Angelo P. Castellani, Salvatore Loreto,
Nicola Bui, and Michele Zorzi
9. Position Paper of the Brno University of Technology Department
of Telecommunications by Vladimir Cervenka, Lubomir Mraz, Milan
Simek, Karel Pavlata
10. Secure Access to IOT Network: An Application-based Group Key
Approach by Samita Chakrabarti, and Wassim Haddad
11. Domain-Insulated Autonomous Network Architecture (DIANA) by W.
Chun
12. Yet Another Definition on Name, Address, ID, and Locator
(YANAIL) by W. Chun
13. The Challenge of Mobility in Low Power Networks by E. Davies
14. If the routing protocol is so smart, why should neighbour
discovery be so dumb? by Nicolas Dejean
Tschofenig & Arkko Expires August 1, 2012 [Page 31]
Internet-Draft Smart Object Workshop Report January 2012
15. Making Smart Objects IPv6 Ready: Where are we? by M. Durvy and
M. Valente
16. Position Paper on "Interconnecting Smart Objects with the
Internet" by Mehmet Ersue, and Jouni Korhonen
17. The Real-time Enterprise: IoT-enabled Business Processes by
Stephan Haller, and Carsten Magerkurth
18. Making Internet-Connected Objects readily useful by Manfred
Hauswirth, Dennis Pfisterer, Stefan Decker
19. Some Considerations on Routing in Particular and Lossy
Environments by Thomas Clausen, and Ulrich Herberg
20. A Security Protocol Adaptation Layer for the IP-based Internet
of Things by Rene Hummen, Tobias Heer, and Klaus Wehrle
21. Simplified SIP Approach for the Smart Object by Ryota Ishibashi,
Takumi Ohba, Arata Koike, and Akira Kurokawa
22. Mobility support for the small and smart Future Internet devices
by Antonio J. Jara, and Antonio F. G. Skarmeta
23. The Need for Efficient Reliable Multicast in Smart Grid Networks
by J. Jetcheva, D. Popa, M.G. Stuber, and H. Van Wyk
24. Lightweight Cryptography for the Internet of Things by Masanobu
Katagi, and Shiho Moriai
25. Thoughts on Reliability in the Internet of Things by James
Kempf, Jari Arkko, Neda Beheshti, and Kiran Yedavalli
26. IKEv2 and Smart Objects by Tero Kivinen
27. Position Paper on Thing Name Service (TNS) for the Internet of
Things (IoT) by Ning Kong, and Shuo Shen
28. Connecting Smart Objects to Wireless WANs by Suresh Krishnan
29. Towards an Information-Centric Internet with more Things by D.
Kutscher, and S. Farrell
30. Application of 6LoWPAN for the Real-Time Positioning of
Manufacturing Assets by Jaacan Martinez and Jose L. M. Lastra
31. Lighting interface to wireless network by Jaroslav Meduna
Tschofenig & Arkko Expires August 1, 2012 [Page 32]
Internet-Draft Smart Object Workshop Report January 2012
32. Social-driven Internet of Connected Objects by Paulo Mendes
33. Protocols should go forward that are required by non IP based
protocols by Tsuyoshi Momose
34. Web services for Wireless Sensor and Actuator Networks by Guido
Moritz
35. Connecting BT-LE sensors to the Internet using Ipv6 by Markus
Isomaeki, Kanji Kerai, Jari Mutikainen, Johanna Nieminen,
Basavaraj Patil, Teemu Savolainen, and Zach Shelby
36. Building Networks by Bruce Nordman
37. Issues and Challenges in Provisioning Keys to Smart Objects by
Yoshihiro Ohba, and Subir Das
38. Challenges and Solutions of Secure Smart Environments by Eila
Ovaska and Antti Evesti
39. Research Experiences about Internetworking Mechanisms to
Integrate Embedded Wireless Networks into Traditional Networks
by Jose F. Martinez, Ivan Corredor, and Miguel S. Familiar
40. Scalable Video Coding in Networked Environment by Naeem Ramzan,
Tomas Piatrik, and Ebroul Izquierdo
41. Challenges in Opportunistic Networking by Mikko Pitkaenen, and
Teemu Kaerkkaeinen
42. Position Statement by Neeli R. Prasad, and Sateesh Addepalli
43. A Gateway Architecture for Interconnecting Smart Objects to the
Internet by Akbar Rahman, Dorothy Gellert, Dale Seed
44. Routing Challenges and Directions for Smart Objects in Future
Internet of Things by T. A. Ramrekha, E. Panaousis, and C.
Politis
45. 6LoWPAN Extension for IPsec by Shahid Raza, Thiemo Voigt, and
Utz Roedig
46. Connected Vehicle as Smart Object(s) by Ryuji Wakikawa
47. Problem and possible approach of development and operation of
Smart Objects by Shoichi Sakane
Tschofenig & Arkko Expires August 1, 2012 [Page 33]
Internet-Draft Smart Object Workshop Report January 2012
48. Connecting Passive RFID Tags to the Internet of Things by Sandra
Dominikus, and Joern-Marc Schmidt
49. Protocol Profiles for Constrained Devices by Juergen
Schoenwaelde, Tina Tsou, and Behcet Sarikaya
50. Multihoming for Sensor Networks by J. Soininen
51. Internet Objects for Building Control by Peter van der Stok, and
Nicolas Riou
52. Optimal information placement for Smart Objects by Shigeya
Suzuki
53. Multi-National Initiative for Cloud Computing in Health Care
(MUNICH) by Christoph Thuemmler
54. The time of the hourglass has elapsed by Laurent Toutain,
Nicolas Montavont, and Dominique Barthel
55. Sensor and Actuator Resource Architecture by Vlasios Tsiatsis,
Jan Hoeller, and Richard Gold
56. IT'S NOT EASY BEING "GREEN" by Margaret Wasserman
57. Trustworthy Wireless Industrial Sensor Networks by Markus
Wehner, Thomas Bartzsch, Dirk Burggraf, Sven Zeisberg, Alexis
Olivereau, and Oualha Nouha
58. Interconnecting smart objects through an overlay networking
architecture by Anastasios Zafeiropoulos, Athanassios
Liakopoulos and Panagiotis Gouvas
59. Building trust among Virtual Interconnecting Smart Objects in
the Future Internet by Theodore Zahariadic, Helen C. Leligou,
Panagiotis Trakadas, and Mischa Dohler
60. Experience and Challenges of Integrating Smart Devices with the
Mobile Internet by Zhen Cao, and Hui Deng
61. The "mesh-under" versus "route over" debate in IP Smart Objects
Networks by JP Vasseur, and Jonathan Hui
62. Identification and Authentication of IoT Devices by Alper Yegin
63. Security Challenges For the Internet of Things by Tim Polk, and
Sean Turner
Tschofenig & Arkko Expires August 1, 2012 [Page 34]
Internet-Draft Smart Object Workshop Report January 2012
64. Application Communications Requirements for 'The Internet of
Things' by Bob Dolin
65. Interoperability Concerns in the Internet of Things by Jari
Arkko
66. Privacy in Ubiquitous Computing by Ivan Gudymenko, and Katrin
Borcea-Pfitzmann
67. The 10 Laws of Smart Object Security Design by Hannes
Tschofenig, and Bernard Aboba
68. Position Paper on "In-Network Object Cloud" Architecture and
Design Goals by Alex Galis, and Stuart Clayman
69. Temptations and Difficulties of Protocols for Smart Objects and
the Internet by Alexandru Petrescu
70. The Internet of Things - Challenge for a New Architecture from
Problems by Gyu Myoung Lee, and Noel Crespi
71. Garrulity and Fluff by Carsten Bormann, and Klaus Hartke
Tschofenig & Arkko Expires August 1, 2012 [Page 35]
Internet-Draft Smart Object Workshop Report January 2012
Appendix D. Workshop Participants
We would like to than the following workshop participants for
attending the workshop:
Adrian Farrel
Akbar Rahman
Alissa Cooper
Alper Yegin
Anastasios Zafeiropoulos
Anders Brandt
Angelo P. Castellani
Antonio F. G. Skarmeta
Antonio Jara
Arvind Ramrekha
Behcet Sarikaya
Bernard Aboba
Bruce Nordman
Carsten Bormann
Cullen Jennings
Daniel Barisic
Dave Thaler
Davide Barbieri
Diego Casado Mansilla
Dirk Kutscher
Dominique Barthel
Dorothy Gellert
Elwyn Davis
Emmanuel Baccelli
Fred Baker
Guido Moritz
Gyu Myoung Lee
Hannes Tschofenig
Hui Deng
Ivan Gudymenko
Jaacan Martinez
Jari Arkko
Jaroslav Meduna
Jeff Burke
Johanna Nieminen
Jonathan Hui
Jonne Soininen
Jouni Korhonen
JP Vasseur
Karel Pavlata
Klaus Hartke
Lars Eggert
Tschofenig & Arkko Expires August 1, 2012 [Page 36]
Internet-Draft Smart Object Workshop Report January 2012
Laura Gheorghe
Laurent Toutain
Lukas Kencl
Marcelo Bagnulo
Marco Valente
Margaret Wasserman
Markus Isomaki
Markus Wehner
Masanobu Katagi
Mathilde Durvy
Mehmet Ersue
Mikko Pitkaenen
Milan Simek
Neeli R. Prasad
Nicolas Dejean
Ning Kong
Pascal Thubert
Paulo Mendes
Pete Resnick
Peter van der Stok
Ralph Droms
Rene Hummen
Ross Callon
Ruediger Martin
Russ Housley
Ryota Ishibashi
Ryuji Wakikawa
Samita Chakrabarti
Sandra Dominikus
Sean Shen
Sean Turner
Shahid Raza
Shoichi Sakane
Spencer Dawkins
Stephan Haller
Stephen Farrell
Stewart Bryant
Subir Das
Suresh Krishnan
Tea Sang Choi
Tero Kivinen
Theodore Zahariadis
Thomas Clausen
Tim Polk
Tina Tsou
Tsuyoshi Momose
Vladimir Cervenka
Wassim Haddad
Tschofenig & Arkko Expires August 1, 2012 [Page 37]
Internet-Draft Smart Object Workshop Report January 2012
Woojik Chun
Zach Shelby
Tschofenig & Arkko Expires August 1, 2012 [Page 38]
Internet-Draft Smart Object Workshop Report January 2012
Authors' Addresses
Hannes Tschofenig
Nokia Siemens Networks
Linnoitustie 6
Espoo 02600
Finland
Phone: +358 (50) 4871445
Email: Hannes.Tschofenig@gmx.net
URI: http://www.tschofenig.priv.at
Jari Arkko
Ericsson
Jorvas 02420
Finland
Email: jari.arkko@piuha.net
Tschofenig & Arkko Expires August 1, 2012 [Page 39]
