Internet DRAFT - draft-ietf-6man-rfc6434-bis
draft-ietf-6man-rfc6434-bis
Internet Engineering Task Force T. Chown
Internet-Draft Jisc
Obsoletes: 6434 (if approved) J. Loughney
Intended status: Best Current Practice Intel
Expires: January 17, 2019 T. Winters
UNH-IOL
July 16, 2018
IPv6 Node Requirements
draft-ietf-6man-rfc6434-bis-09
Abstract
This document defines requirements for IPv6 nodes. It is expected
that IPv6 will be deployed in a wide range of devices and situations.
Specifying the requirements for IPv6 nodes allows IPv6 to function
well and interoperate in a large number of situations and
deployments.
This document obsoletes RFC 6434, and in turn RFC 4294.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on January 17, 2019.
Copyright Notice
Copyright (c) 2018 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
Chown, et al. Expires January 17, 2019 [Page 1]
Internet-Draft IPv6 Node Requirements July 2018
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Scope of This Document . . . . . . . . . . . . . . . . . 4
1.2. Description of IPv6 Nodes . . . . . . . . . . . . . . . . 4
2. Requirements Language . . . . . . . . . . . . . . . . . . . . 5
3. Abbreviations Used in This Document . . . . . . . . . . . . . 5
4. Sub-IP Layer . . . . . . . . . . . . . . . . . . . . . . . . 5
5. IP Layer . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5.1. Internet Protocol Version 6 - RFC 8200 . . . . . . . . . 6
5.2. Support for IPv6 Extension Headers . . . . . . . . . . . 7
5.3. Protecting a node from excessive EH options . . . . . . . 8
5.4. Neighbor Discovery for IPv6 - RFC 4861 . . . . . . . . . 9
5.5. SEcure Neighbor Discovery (SEND) - RFC 3971 . . . . . . . 10
5.6. IPv6 Router Advertisement Flags Option - RFC 5175 . . . . 11
5.7. Path MTU Discovery and Packet Size . . . . . . . . . . . 11
5.7.1. Path MTU Discovery - RFC 8201 . . . . . . . . . . . . 11
5.7.2. Minimum MTU considerations . . . . . . . . . . . . . 12
5.8. ICMP for the Internet Protocol Version 6 (IPv6) - RFC
4443 . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.9. Default Router Preferences and More-Specific Routes - RFC
4191 . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.10. First-Hop Router Selection - RFC 8028 . . . . . . . . . . 12
5.11. Multicast Listener Discovery (MLD) for IPv6 - RFC 3810 . 12
5.12. Explicit Congestion Notification (ECN) - RFC 3168 . . . . 13
6. Addressing and Address Configuration . . . . . . . . . . . . 13
6.1. IP Version 6 Addressing Architecture - RFC 4291 . . . . . 13
6.2. Host Address Availability Recommendations . . . . . . . . 13
6.3. IPv6 Stateless Address Autoconfiguration - RFC 4862 . . . 14
6.4. Privacy Extensions for Address Configuration in IPv6 -
RFC 4941 . . . . . . . . . . . . . . . . . . . . . . . . 15
6.5. Stateful Address Autoconfiguration (DHCPv6) - RFC 3315 . 15
6.6. Default Address Selection for IPv6 - RFC 6724 . . . . . . 16
7. DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8. Configuring Non-Address Information . . . . . . . . . . . . . 16
8.1. DHCP for Other Configuration Information . . . . . . . . 16
8.2. Router Advertisements and Default Gateway . . . . . . . . 17
8.3. IPv6 Router Advertisement Options for DNS
Configuration - RFC 8106 . . . . . . . . . . . . . . . . 17
8.4. DHCP Options versus Router Advertisement Options for Host
Configuration . . . . . . . . . . . . . . . . . . . . . . 17
9. Service Discovery Protocols . . . . . . . . . . . . . . . . . 18
Chown, et al. Expires January 17, 2019 [Page 2]
Internet-Draft IPv6 Node Requirements July 2018
10. IPv4 Support and Transition . . . . . . . . . . . . . . . . . 18
10.1. Transition Mechanisms . . . . . . . . . . . . . . . . . 18
10.1.1. Basic Transition Mechanisms for IPv6 Hosts and
Routers - RFC 4213 . . . . . . . . . . . . . . . . . 18
11. Application Support . . . . . . . . . . . . . . . . . . . . . 18
11.1. Textual Representation of IPv6 Addresses - RFC 5952 . . 18
11.2. Application Programming Interfaces (APIs) . . . . . . . 18
12. Mobility . . . . . . . . . . . . . . . . . . . . . . . . . . 19
13. Security . . . . . . . . . . . . . . . . . . . . . . . . . . 20
13.1. Requirements . . . . . . . . . . . . . . . . . . . . . . 21
13.2. Transforms and Algorithms . . . . . . . . . . . . . . . 21
14. Router-Specific Functionality . . . . . . . . . . . . . . . . 21
14.1. IPv6 Router Alert Option - RFC 2711 . . . . . . . . . . 22
14.2. Neighbor Discovery for IPv6 - RFC 4861 . . . . . . . . . 22
14.3. Stateful Address Autoconfiguration (DHCPv6) - RFC 3315 . 22
14.4. IPv6 Prefix Length Recommendation for Forwarding - BCP
198 . . . . . . . . . . . . . . . . . . . . . . . . . . 23
15. Constrained Devices . . . . . . . . . . . . . . . . . . . . . 23
16. IPv6 Node Management . . . . . . . . . . . . . . . . . . . . 23
16.1. Management Information Base (MIB) Modules . . . . . . . 23
16.1.1. IP Forwarding Table MIB . . . . . . . . . . . . . . 24
16.1.2. Management Information Base for the Internet
Protocol (IP) . . . . . . . . . . . . . . . . . . . 24
16.1.3. Interface MIB . . . . . . . . . . . . . . . . . . . 24
16.2. YANG Data Models . . . . . . . . . . . . . . . . . . . . 24
16.2.1. IP Management YANG Model . . . . . . . . . . . . . . 24
16.2.2. Interface Management YANG Model . . . . . . . . . . 24
17. Security Considerations . . . . . . . . . . . . . . . . . . . 24
18. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 24
19. Authors and Acknowledgments . . . . . . . . . . . . . . . . . 24
19.1. Authors and Acknowledgments (Current Document) . . . . . 25
19.2. Authors and Acknowledgments from RFC 6434 . . . . . . . 25
19.3. Authors and Acknowledgments from RFC 4294 . . . . . . . 25
20. Appendix: Changes from RFC 6434 . . . . . . . . . . . . . . . 25
21. Appendix: Changes from RFC 4294 . . . . . . . . . . . . . . . 27
22. References . . . . . . . . . . . . . . . . . . . . . . . . . 28
22.1. Normative References . . . . . . . . . . . . . . . . . . 28
22.2. Informative References . . . . . . . . . . . . . . . . . 35
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 40
1. Introduction
This document defines common functionality required by both IPv6
hosts and routers. Many IPv6 nodes will implement optional or
additional features, but this document collects and summarizes
requirements from other published Standards Track documents in one
place.
Chown, et al. Expires January 17, 2019 [Page 3]
Internet-Draft IPv6 Node Requirements July 2018
This document tries to avoid discussion of protocol details and
references RFCs for this purpose. This document is intended to be an
applicability statement and to provide guidance as to which IPv6
specifications should be implemented in the general case and which
specifications may be of interest to specific deployment scenarios.
This document does not update any individual protocol document RFCs.
Although this document points to different specifications, it should
be noted that in many cases, the granularity of a particular
requirement will be smaller than a single specification, as many
specifications define multiple, independent pieces, some of which may
not be mandatory. In addition, most specifications define both
client and server behavior in the same specification, while many
implementations will be focused on only one of those roles.
This document defines a minimal level of requirement needed for a
device to provide useful internet service and considers a broad range
of device types and deployment scenarios. Because of the wide range
of deployment scenarios, the minimal requirements specified in this
document may not be sufficient for all deployment scenarios. It is
perfectly reasonable (and indeed expected) for other profiles to
define additional or stricter requirements appropriate for specific
usage and deployment environments. For example, this document does
not mandate that all clients support DHCP, but some deployment
scenarios may deem it appropriate to make such a requirement. For
example, NIST has defined profiles for specialized requirements for
IPv6 in target environments (see [USGv6]).
As it is not always possible for an implementer to know the exact
usage of IPv6 in a node, an overriding requirement for IPv6 nodes is
that they should adhere to Jon Postel's Robustness Principle: "Be
conservative in what you do, be liberal in what you accept from
others" [RFC0793].
1.1. Scope of This Document
IPv6 covers many specifications. It is intended that IPv6 will be
deployed in many different situations and environments. Therefore,
it is important to develop requirements for IPv6 nodes to ensure
interoperability.
1.2. Description of IPv6 Nodes
From the Internet Protocol, Version 6 (IPv6) Specification [RFC8200],
we have the following definitions:
Chown, et al. Expires January 17, 2019 [Page 4]
Internet-Draft IPv6 Node Requirements July 2018
IPv6 node - a device that implements IPv6.
IPv6 router - a node that forwards IPv6 packets not explicitly
addressed to itself.
IPv6 host - any IPv6 node that is not a router.
2. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119]
8174 [RFC8174] when, and only when, they appear in all capitals, as
show here.
3. Abbreviations Used in This Document
AH Authentication Header
DAD Duplicate Address Detection
ESP Encapsulating Security Payload
ICMP Internet Control Message Protocol
IKE Internet Key Exchange
MIB Management Information Base
MLD Multicast Listener Discovery
MTU Maximum Transmission Unit
NA Neighbor Advertisement
NBMA Non-Broadcast Multiple Access
ND Neighbor Discovery
NS Neighbor Solicitation
NUD Neighbor Unreachability Detection
PPP Point-to-Point Protocol
4. Sub-IP Layer
An IPv6 node MUST include support for one or more IPv6 link-layer
specifications. Which link-layer specifications an implementation
should include will depend upon what link-layers are supported by the
hardware available on the system. It is possible for a conformant
IPv6 node to support IPv6 on some of its interfaces and not on
others.
As IPv6 is run over new layer 2 technologies, it is expected that new
specifications will be issued. In the following, we list some of the
layer 2 technologies for which an IPv6 specification has been
developed. It is provided for informational purposes only and may
not be complete.
- Transmission of IPv6 Packets over Ethernet Networks [RFC2464]
Chown, et al. Expires January 17, 2019 [Page 5]
Internet-Draft IPv6 Node Requirements July 2018
- Transmission of IPv6 Packets over Frame Relay Networks
Specification [RFC2590]
- Transmission of IPv6 Packets over IEEE 1394 Networks [RFC3146]
- Transmission of IPv6, IPv4, and Address Resolution Protocol (ARP)
Packets over Fibre Channel [RFC4338]
- Transmission of IPv6 Packets over IEEE 802.15.4 Networks [RFC4944]
- Transmission of IPv6 via the IPv6 Convergence Sublayer over IEEE
802.16 Networks [RFC5121]
- IP version 6 over PPP [RFC5072]
In addition to traditional physical link-layers, it is also possible
to tunnel IPv6 over other protocols. Examples include:
- Teredo: Tunneling IPv6 over UDP through Network Address
Translations (NATs) [RFC4380]
- Section 3 of "Basic Transition Mechanisms for IPv6 Hosts and
Routers" [RFC4213]
5. IP Layer
5.1. Internet Protocol Version 6 - RFC 8200
The Internet Protocol Version 6 is specified in [RFC8200]. This
specification MUST be supported.
The node MUST follow the packet transmission rules in RFC 8200.
All conformant IPv6 implementations MUST be capable of sending and
receiving IPv6 packets; forwarding functionality MAY be supported.
Nodes MUST always be able to send, receive, and process fragment
headers.
IPv6 nodes MUST not create overlapping fragments. Also, when
reassembling an IPv6 datagram, if one or more of its constituent
fragments is determined to be an overlapping fragment, the entire
datagram (and any constituent fragments) MUST be silently discarded.
See [RFC5722] for more information.
As recommended in [RFC8021], nodes MUST NOT generate atomic
fragments, i.e., where the fragment is a whole datagram. As per
[RFC6946], if a receiving node reassembling a datagram encounters an
atomic fragment, it should be processed as a fully reassembled
Chown, et al. Expires January 17, 2019 [Page 6]
Internet-Draft IPv6 Node Requirements July 2018
packet, and any other fragments that match this packet should be
processed independently.
To mitigate a variety of potential attacks, nodes SHOULD avoid using
predictable fragment Identification values in Fragment Headers, as
discussed in [RFC7739].
All nodes SHOULD support the setting and use of the IPv6 Flow Label
field as defined in the IPv6 Flow Label specification [RFC6437].
Forwarding nodes such as routers and load distributors MUST NOT
depend only on Flow Label values being uniformly distributed. It is
RECOMMENDED that source hosts support the flow label by setting the
Flow Label field for all packets of a given flow to the same value
chosen from an approximation to a discrete uniform distribution.
5.2. Support for IPv6 Extension Headers
RFC 8200 specifies extension headers and the processing for these
headers.
Extension headers (except for the Hop-by-Hop Options header) are not
processed, inserted, or deleted by any node along a packet's delivery
path, until the packet reaches the node (or each of the set of nodes,
in the case of multicast) identified in the Destination Address field
of the IPv6 header.
Any unrecognized extension headers or options MUST be processed as
described in RFC 8200. Note that where Section 4 of RFC 8200 refers
to the action to be taken when a Next Header value in the current
header is not recognized by a node, that action applies whether the
value is an unrecognized Extension Header or an unrecognized upper
layer protocol (ULP).
An IPv6 node MUST be able to process these extension headers. An
exception is Routing Header type 0 (RH0), which was deprecated by
[RFC5095] due to security concerns and which MUST be treated as an
unrecognized routing type.
Further, [RFC7045] adds specific requirements for processing of
Extension Headers, in particular that any forwarding node along an
IPv6 packet's path, which forwards the packet for any reason, SHOULD
do so regardless of any extension headers that are present.
As per RFC 8200, when a node fragments an IPv6 datagram, it MUST
include the entire IPv6 Header Chain in the first fragment. The Per-
Fragment headers MUST consist of the IPv6 header plus any extension
headers that MUST be processed by nodes en route to the destination,
that is, all headers up to and including the Routing header if
Chown, et al. Expires January 17, 2019 [Page 7]
Internet-Draft IPv6 Node Requirements July 2018
present, else the Hop-by-Hop Options header if present, else no
extension headers. On reassembly, if the first fragment does not
include all headers through an Upper-Layer header, then that fragment
SHOULD be discarded and an ICMP Parameter Problem, Code 3, message
SHOULD be sent to the source of the fragment, with the Pointer field
set to zero. See [RFC7112] for a discussion of why oversized IPv6
Extension Header chains are avoided.
Defining new IPv6 extension headers is not recommended, unless there
are no existing IPv6 extension headers that can be used by specifying
a new option for that IPv6 extension header. A proposal to specify a
new IPv6 extension header MUST include a detailed technical
explanation of why an existing IPv6 extension header can not be used
for the desired new function, and in such cases need to follow the
format described in Section 8 of RFC 8200. For further background
reading on this topic, see [RFC6564].
5.3. Protecting a node from excessive EH options
As per RFC 8200, end hosts are expected to process all extension
headers, destination options, and hop-by-hop options in a packet.
Given that the only limit on the number and size of extension headers
is the MTU, the processing of received packets could be considerable.
It is also conceivable that a long chain of extension headers might
be used as a form of denial-of-service attack. Accordingly, a host
may place limits on the number and sizes of extension headers and
options it is willing to process.
A host MAY limit the number of consecutive PAD1 options in
destination options or hop-by-hop options to seven. In this case, if
the more than seven consecutive PAD1 options are present the packet
MAY be silently discarded. The rationale is that if padding of eight
or more bytes is required than the PADN option SHOULD be used.
A host MAY limit number of bytes in a PADN option to be less than
eight. In such a case, if a PADN option is present that has a length
greater than seven then the packet SHOULD be silently discarded. The
rationale for this guideline is that the purpose of padding is for
alignment and eight bytes is the maximum alignment used in IPv6.
A host MAY disallow unknown options in destination options or hop-by-
hop options. This SHOULD be configurable where the default is to
accept unknown options and process them per [RFC8200]. If a packet
with unknown options is received and the host is configured to
disallow them, then the packet SHOULD be silently discarded.
A host MAY impose a limit on the maximum number of non-padding
options allowed in the destination options and hop-by-hop extension
Chown, et al. Expires January 17, 2019 [Page 8]
Internet-Draft IPv6 Node Requirements July 2018
headers. If this feature is supported the maximum number SHOULD be
configurable and the default value SHOULD be set to eight. The
limits for destination options and hop-by-hop options may be
separately configurable. If a packet is received and the number of
destination or hop-by-hop options exceeds the limit, then the packet
SHOULD be silently discarded.
A host MAY impose a limit on the maximum length of destination
options or hop-by-hop options extension header. This value SHOULD be
configurable and the default is to accept options of any length. If
a packet is received and the length of destination or hop-by-hop
options extension header exceeds the length limit, then the packet
SHOULD be silently discarded.
5.4. Neighbor Discovery for IPv6 - RFC 4861
Neighbor Discovery is defined in [RFC4861]; the definition was
updated by [RFC5942]. Neighbor Discovery SHOULD be supported. RFC
4861 states:
Unless specified otherwise (in a document that covers operating IP
over a particular link type) this document applies to all link
types. However, because ND uses link-layer multicast for some of
its services, it is possible that on some link types (e.g., Non-
Broadcast Multi-Access (NBMA) links), alternative protocols or
mechanisms to implement those services will be specified (in the
appropriate document covering the operation of IP over a
particular link type). The services described in this document
that are not directly dependent on multicast, such as Redirects,
next-hop determination, Neighbor Unreachability Detection, etc.,
are expected to be provided as specified in this document. The
details of how one uses ND on NBMA links are addressed in
[RFC2491].
Some detailed analysis of Neighbor Discovery follows:
Router Discovery is how hosts locate routers that reside on an
attached link. Hosts MUST support Router Discovery functionality.
Prefix Discovery is how hosts discover the set of address prefixes
that define which destinations are on-link for an attached link.
Hosts MUST support Prefix Discovery.
Hosts MUST also implement Neighbor Unreachability Detection (NUD) for
all paths between hosts and neighboring nodes. NUD is not required
for paths between routers. However, all nodes MUST respond to
unicast Neighbor Solicitation (NS) messages.
Chown, et al. Expires January 17, 2019 [Page 9]
Internet-Draft IPv6 Node Requirements July 2018
[RFC7048] discusses NUD, in particular cases where it behaves too
impatiently. It states that if a node transmits more than a certain
number of packets, then it SHOULD use the exponential backoff of the
retransmit timer, up to a certain threshold point.
Hosts MUST support the sending of Router Solicitations and the
receiving of Router Advertisements. The ability to understand
individual Router Advertisement options is dependent on supporting
the functionality making use of the particular option.
[RFC7559] discusses packet loss resiliency for Router Solicitations,
and requires that nodes MUST use a specific exponential backoff
algorithm for RS retransmissions.
All nodes MUST support the sending and receiving of Neighbor
Solicitation (NS) and Neighbor Advertisement (NA) messages. NS and
NA messages are required for Duplicate Address Detection (DAD).
Hosts SHOULD support the processing of Redirect functionality.
Routers MUST support the sending of Redirects, though not necessarily
for every individual packet (e.g., due to rate limiting). Redirects
are only useful on networks supporting hosts. In core networks
dominated by routers, Redirects are typically disabled. The sending
of Redirects SHOULD be disabled by default on routers intended to
deployed on core networks. They MAY be enabled by default on routers
intended to support hosts on edge networks.
"IPv6 Host-to-Router Load Sharing" [RFC4311] includes additional
recommendations on how to select from a set of available routers.
[RFC4311] SHOULD be supported.
5.5. SEcure Neighbor Discovery (SEND) - RFC 3971
SEND [RFC3971] and Cryptographically Generated Addresses (CGAs)
[RFC3972] provide a way to secure the message exchanges of Neighbor
Discovery. SEND has the potential to address certain classes of
spoofing attacks, but it does not provide specific protection for
threats from off-link attackers.
There have been relatively few implementations of SEND in common
operating systems and platforms since its publication in 2005, and
thus deployment experience remains very limited to date.
At this time, support for SEND is considered optional. Due to the
complexity in deploying SEND, and its heavyweight provisioning, its
deployment is only likely to be considered where nodes are operating
in a particularly strict security environment.
Chown, et al. Expires January 17, 2019 [Page 10]
Internet-Draft IPv6 Node Requirements July 2018
5.6. IPv6 Router Advertisement Flags Option - RFC 5175
Router Advertisements include an 8-bit field of single-bit Router
Advertisement flags. The Router Advertisement Flags Option extends
the number of available flag bits by 48 bits. At the time of this
writing, 6 of the original 8 single-bit flags have been assigned,
while 2 remain available for future assignment. No flags have been
defined that make use of the new option, and thus, strictly speaking,
there is no requirement to implement the option today. However,
implementations that are able to pass unrecognized options to a
higher-level entity that may be able to understand them (e.g., a
user-level process using a "raw socket" facility) MAY take steps to
handle the option in anticipation of a future usage.
5.7. Path MTU Discovery and Packet Size
5.7.1. Path MTU Discovery - RFC 8201
"Path MTU Discovery for IP version 6" [RFC8201] SHOULD be supported.
From [RFC8200]:
It is strongly recommended that IPv6 nodes implement Path MTU
Discovery [RFC8201], in order to discover and take advantage of
path MTUs greater than 1280 octets. However, a minimal IPv6
implementation (e.g., in a boot ROM) may simply restrict itself to
sending packets no larger than 1280 octets, and omit
implementation of Path MTU Discovery.
The rules in [RFC8200] and [RFC5722] MUST be followed for packet
fragmentation and reassembly.
As described in RFC 8201, nodes implementing Path MTU Discovery and
sending packets larger than the IPv6 minimum link MTU are susceptible
to problematic connectivity if ICMPv6 messages are blocked or not
transmitted. For example, this will result in connections that
complete the TCP three-way handshake correctly but then hang when
data is transferred. This state is referred to as a black-hole
connection [RFC2923]. Path MTU Discovery relies on ICMPv6 Packet Too
Big (PTB) to determine the MTU of the path (and thus these MUST not
be filtered, as per the recommendation in [RFC4890]).
An alternative to Path MTU Discovery defined in RFC 8201 can be found
in [RFC4821], which defines a method for Packetization Layer Path MTU
Discovery (PLPMTUD) designed for use over paths where delivery of
ICMPv6 messages to a host is not assured.
Chown, et al. Expires January 17, 2019 [Page 11]
Internet-Draft IPv6 Node Requirements July 2018
5.7.2. Minimum MTU considerations
While an IPv6 link MTU can be set to 1280 bytes, it is recommended
that for IPv6 UDP in particular, which includes DNS operation, the
sender use a large MTU if they can, in order to avoid gratuitous
fragmentation-caused packet drops.
5.8. ICMP for the Internet Protocol Version 6 (IPv6) - RFC 4443
ICMPv6 [RFC4443] MUST be supported. "Extended ICMP to Support Multi-
Part Messages" [RFC4884] MAY be supported.
5.9. Default Router Preferences and More-Specific Routes - RFC 4191
"Default Router Preferences and More-Specific Routes" [RFC4191]
provides support for nodes attached to multiple (different) networks,
each providing routers that advertise themselves as default routers
via Router Advertisements. In some scenarios, one router may provide
connectivity to destinations the other router does not, and choosing
the "wrong" default router can result in reachability failures. In
order to resolve this scenario IPv6 Nodes MUST implement [RFC4191]
and SHOULD implement the Type C host role defined in RFC4191.
5.10. First-Hop Router Selection - RFC 8028
In multihomed scenarios, where a host has more than one prefix, each
allocated by an upstream network that is assumed to implement BCP 38
ingress filtering, the host may have multiple routers to choose from.
Hosts that may be deployed in such multihomed environments SHOULD
follow the guidance given in [RFC8028].
5.11. Multicast Listener Discovery (MLD) for IPv6 - RFC 3810
Nodes that need to join multicast groups MUST support MLDv2
[RFC3810]. MLD is needed by any node that is expected to receive and
process multicast traffic and in particular MLDv2 is required for
support for source-specific multicast (SSM) as per [RFC4607].
Previous versions of this document only required MLDv1 ([RFC2710]) to
be implemented on all nodes. Since participation of any MLDv1-only
nodes on a link require that all other nodeas on the link then
operate in version 1 compatibility mode, the requirement to support
MLDv2 on all nodes was upgraded to a MUST. Further, SSM is now the
preferred multicast distribution method, rather than ASM.
Chown, et al. Expires January 17, 2019 [Page 12]
Internet-Draft IPv6 Node Requirements July 2018
Note that Neighbor Discovery (as used on most link types -- see
Section 5.4) depends on multicast and requires that nodes join
Solicited Node multicast addresses.
5.12. Explicit Congestion Notification (ECN) - RFC 3168
An ECN-aware router sets a mark in the IP header in order to signal
impending congestion, rather than dropping a packet. The receiver of
the packet echoes the congestion indication to the sender, which can
then reduce its transmission rate as if it detected a dropped packet.
Nodes SHOULD support [RFC3168] by implementing an interface for the
upper layer to access and set the ECN bits in the IP header. The
benefits of using ECN are documented in [RFC8087].
6. Addressing and Address Configuration
6.1. IP Version 6 Addressing Architecture - RFC 4291
The IPv6 Addressing Architecture [RFC4291] MUST be supported.
The current IPv6 Address Architecture is based on a 64-bit boundary
for subnet prefixes. The reasoning behind this decision is
documented in [RFC7421].
Implementations MUST also support the Multicast flag updates
documented in [RFC7371]
6.2. Host Address Availability Recommendations
Hosts may be configured with addresses through a variety of methods,
including SLAAC, DHCPv6, or manual configuration.
[RFC7934] recommends that networks provide general-purpose end hosts
with multiple global IPv6 addresses when they attach, and it
describes the benefits of and the options for doing so. Routers
SHOULD support [RFC7934] for assigning multiple address to a host.
Host SHOULD support assigning multiple addresses as described in
[RFC7934].
Nodes SHOULD support the capability to be assigned a prefix per host
as documented in [RFC8273]. Such an approach can offer improved host
isolation and enhanced subscriber management on shared network
segments.
Chown, et al. Expires January 17, 2019 [Page 13]
Internet-Draft IPv6 Node Requirements July 2018
6.3. IPv6 Stateless Address Autoconfiguration - RFC 4862
Hosts MUST support IPv6 Stateless Address Autoconfiguration. It is
RECOMMENDED, as described in [RFC8064], that unless there is a
specific requirement for MAC addresses to be embedded in an IID,
nodes follow the procedure in [RFC7217] to generate SLAAC-based
addresses, rather than using [RFC4862]. Addresses generated through
RFC7217 will be the same whenever a given device (re)appears on the
same subnet (with a specific IPv6 prefix), but the IID will vary on
each subnet visited.
Nodes that are routers MUST be able to generate link-local addresses
as described in [RFC4862].
From RFC 4862:
The autoconfiguration process specified in this document applies
only to hosts and not routers. Since host autoconfiguration uses
information advertised by routers, routers will need to be
configured by some other means. However, it is expected that
routers will generate link-local addresses using the mechanism
described in this document. In addition, routers are expected to
successfully pass the Duplicate Address Detection procedure
described in this document on all addresses prior to assigning
them to an interface.
All nodes MUST implement Duplicate Address Detection. Quoting from
Section 5.4 of RFC 4862:
Duplicate Address Detection MUST be performed on all unicast
addresses prior to assigning them to an interface, regardless of
whether they are obtained through stateless autoconfiguration,
DHCPv6, or manual configuration, with the following [exceptions
noted therein].
"Optimistic Duplicate Address Detection (DAD) for IPv6" [RFC4429]
specifies a mechanism to reduce delays associated with generating
addresses via Stateless Address Autoconfiguration [RFC4862]. RFC
4429 was developed in conjunction with Mobile IPv6 in order to reduce
the time needed to acquire and configure addresses as devices quickly
move from one network to another, and it is desirable to minimize
transition delays. For general purpose devices, RFC 4429 remains
optional at this time.
[RFC7527] discusses enhanced DAD, and describes an algorithm to
automate the detection of looped back IPv6 ND messages used by DAD.
Nodes SHOULD implement this behaviour where such detection is
beneficial.
Chown, et al. Expires January 17, 2019 [Page 14]
Internet-Draft IPv6 Node Requirements July 2018
6.4. Privacy Extensions for Address Configuration in IPv6 - RFC 4941
A node using Stateless Address Autoconfiguration [RFC4862] to form a
globally unique IPv6 address using its MAC address to generate the
IID will see that IID remain the same on any visited network, even
though the network prefix part changes. Thus it is possible for 3rd
party device to track the activities of the node they communicate
with, as that node moves around the network. Privacy Extensions for
Stateless Address Autoconfiguration [RFC4941] address this concern by
allowing nodes to configure an additional temporary address where the
IID is effectively randomly generated. Privacy addresses are then
used as source addresses for new communications initiated by the
node.
General issues regarding privacy issues for IPv6 addressing are
discussed in [RFC7721].
RFC 4941 SHOULD be supported. In some scenarios, such as dedicated
servers in a data center, it provides limited or no benefit, or may
complicate network management. Thus devices implementing this
specification MUST provide a way for the end user to explicitly
enable or disable the use of such temporary addresses.
Note that RFC4941 can be used independently of traditional SLAAC, or
of RFC7217-based SLAAC.
Implementers of RFC 4941 should be aware that certain addresses are
reserved and should not be chosen for use as temporary addresses.
Consult "Reserved IPv6 Interface Identifiers" [RFC5453] for more
details.
6.5. Stateful Address Autoconfiguration (DHCPv6) - RFC 3315
DHCPv6 [RFC3315] can be used to obtain and configure addresses. In
general, a network may provide for the configuration of addresses
through SLAAC, DHCPv6, or both. There will be a wide range of IPv6
deployment models and differences in address assignment requirements,
some of which may require DHCPv6 for stateful address assignment.
Consequently, all hosts SHOULD implement address configuration via
DHCPv6.
In the absence of observed Router Advertisement messages, IPv6 nodes
MAY initiate DHCP to obtain IPv6 addresses and other configuration
information, as described in Section 5.5.2 of [RFC4862].
Where devices are likely to be carried by users and attached to
multiple visisted networks, DHCPv6 client anonymity profiles SHOULD
be supported as described in [RFC7844] to minimise the disclosure of
Chown, et al. Expires January 17, 2019 [Page 15]
Internet-Draft IPv6 Node Requirements July 2018
identifying information. Section 5 of RFC7844 describes operational
considerations on the use of such anonymity profiles.
6.6. Default Address Selection for IPv6 - RFC 6724
IPv6 nodes will invariably have multiple addresses configured
simultaneously, and thus will need to choose which addresses to use
for which communications. The rules specified in the Default Address
Selection for IPv6 [RFC6724] document MUST be implemented. [RFC8028]
updates rule 5.5 from [RFC6724]; implementations SHOULD implement
this rule.
7. DNS
DNS is described in [RFC1034], [RFC1035], [RFC3363], and [RFC3596].
Not all nodes will need to resolve names; those that will never need
to resolve DNS names do not need to implement resolver functionality.
However, the ability to resolve names is a basic infrastructure
capability on which applications rely, and most nodes will need to
provide support. All nodes SHOULD implement stub-resolver [RFC1034]
functionality, as in [RFC1034], Section 5.3.1, with support for:
- AAAA type Resource Records [RFC3596];
- reverse addressing in ip6.arpa using PTR records [RFC3596];
- Extension Mechanisms for DNS (EDNS0) [RFC6891] to allow for DNS
packet sizes larger than 512 octets.
Those nodes are RECOMMENDED to support DNS security extensions
[RFC4033] [RFC4034] [RFC4035].
A6 Resource Records, which were only ever defined with Experimental
status in [RFC3363], are now classified as Historic, as per
[RFC6563].
8. Configuring Non-Address Information
8.1. DHCP for Other Configuration Information
DHCP [RFC3315] Specifies a mechanism for IPv6 nodes to obtain address
configuration information (see Section 6.5) and to obtain additional
(non-address) configuration. If a host implementation supports
applications or other protocols that require configuration that is
only available via DHCP, hosts SHOULD implement DHCP. For
specialized devices on which no such configuration need is present,
DHCP may not be necessary.
Chown, et al. Expires January 17, 2019 [Page 16]
Internet-Draft IPv6 Node Requirements July 2018
An IPv6 node can use the subset of DHCP (described in [RFC3736]) to
obtain other configuration information.
If an IPv6 node implements DHCP it MUST implement the DNS options
[RFC3646] as most deployments will expect these options are
available.
8.2. Router Advertisements and Default Gateway
There is no defined DHCPv6 Gateway option.
Nodes using the Dynamic Host Configuration Protocol for IPv6 (DHCPv6)
are thus expected to determine their default router information and
on-link prefix information from received Router Advertisements.
8.3. IPv6 Router Advertisement Options for DNS Configuration - RFC 8106
Router Advertisement Options have historically been limited to those
that are critical to basic IPv6 functionality. Originally, DNS
configuration was not included as an RA option, and DHCP was the
recommended way to obtain DNS configuration information. Over time,
the thinking surrounding such an option has evolved. It is now
generally recognized that few nodes can function adequately without
having access to a working DNS resolver, and thus a Standards Track
document has been published to provide this capability [RFC8106].
Implementations MUST include support for the DNS RA option [RFC8106].
8.4. DHCP Options versus Router Advertisement Options for Host
Configuration
In IPv6, there are two main protocol mechanisms for propagating
configuration information to hosts: Router Advertisements (RAs) and
DHCP. RA options have been restricted to those deemed essential for
basic network functioning and for which all nodes are configured with
exactly the same information. Examples include the Prefix
Information Options, the MTU option, etc. On the other hand, DHCP
has generally been preferred for configuration of more general
parameters and for parameters that may be client-specific. Generally
speaking, however, there has been a desire to define only one
mechanism for configuring a given option, rather than defining
multiple (different) ways of configuring the same information.
One issue with having multiple ways of configuring the same
information is that interoperability suffers if a host chooses one
mechanism but the network operator chooses a different mechanism.
For "closed" environments, where the network operator has significant
influence over what devices connect to the network and thus what
Chown, et al. Expires January 17, 2019 [Page 17]
Internet-Draft IPv6 Node Requirements July 2018
configuration mechanisms they support, the operator may be able to
ensure that a particular mechanism is supported by all connected
hosts. In more open environments, however, where arbitrary devices
may connect (e.g., a WIFI hotspot), problems can arise. To maximize
interoperability in such environments, hosts would need to implement
multiple configuration mechanisms to ensure interoperability.
9. Service Discovery Protocols
[RFC6762] and [RFC6763] describe multicast DNS (mDNS) and DNS-Based
Service Discovery (DNS-SD) respectively. These protocols,
collectively commonly referred to as the 'Bonjour' protocols after
their naming by Apple, provide the means for devices to discover
services within a local link and, in the absence of a unicast DNS
service, to exchange naming information.
Where devices are to be deployed in networks where service dicovery
would be beneficial, e.g., for users seeking to discover printers or
display devices, mDNS and DNS-SD SHOULD be supported.
10. IPv4 Support and Transition
IPv6 nodes MAY support IPv4.
10.1. Transition Mechanisms
10.1.1. Basic Transition Mechanisms for IPv6 Hosts and Routers - RFC
4213
If an IPv6 node implements dual stack and tunneling, then [RFC4213]
MUST be supported.
11. Application Support
11.1. Textual Representation of IPv6 Addresses - RFC 5952
Software that allows users and operators to input IPv6 addresses in
text form SHOULD support "A Recommendation for IPv6 Address Text
Representation" [RFC5952].
11.2. Application Programming Interfaces (APIs)
There are a number of IPv6-related APIs. This document does not
mandate the use of any, because the choice of API does not directly
relate to on-the-wire behavior of protocols. Implementers, however,
would be advised to consider providing a common API or reviewing
existing APIs for the type of functionality they provide to
applications.
Chown, et al. Expires January 17, 2019 [Page 18]
Internet-Draft IPv6 Node Requirements July 2018
"Basic Socket Interface Extensions for IPv6" [RFC3493] provides IPv6
functionality used by typical applications. Implementers should note
that RFC3493 has been picked up and further standardized by the
Portable Operating System Interface (POSIX) [POSIX].
"Advanced Sockets Application Program Interface (API) for IPv6"
[RFC3542] provides access to advanced IPv6 features needed by
diagnostic and other more specialized applications.
"IPv6 Socket API for Source Address Selection" [RFC5014] provides
facilities that allow an application to override the default Source
Address Selection rules of [RFC6724].
"Socket Interface Extensions for Multicast Source Filters" [RFC3678]
provides support for expressing source filters on multicast group
memberships.
"Extension to Sockets API for Mobile IPv6" [RFC4584] provides
application support for accessing and enabling Mobile IPv6 [RFC6275]
features.
12. Mobility
Mobile IPv6 [RFC6275] and associated specifications [RFC3776]
[RFC4877] allow a node to change its point of attachment within the
Internet, while maintaining (and using) a permanent address. All
communication using the permanent address continues to proceed as
expected even as the node moves around. The definition of Mobile IP
includes requirements for the following types of nodes:
- mobile nodes
- correspondent nodes with support for route optimization
- home agents
- all IPv6 routers
At the present time, Mobile IP has seen only limited implementation
and no significant deployment, partly because it originally assumed
an IPv6-only environment rather than a mixed IPv4/IPv6 Internet.
Recently, additional work has been done to support mobility in mixed-
mode IPv4 and IPv6 networks [RFC5555].
More usage and deployment experience is needed with mobility before
any specific approach can be recommended for broad implementation in
all hosts and routers. Consequently, [RFC6275], [RFC5555], and
Chown, et al. Expires January 17, 2019 [Page 19]
Internet-Draft IPv6 Node Requirements July 2018
associated standards such as [RFC4877] are considered a MAY at this
time.
IPv6 for 3GPP [RFC7066] lists a snapshot of required IPv6
Functionalities at the time the document was published that would
need to be implemented, going above and beyond the recommendations in
this document. Additionally a 3GPP IPv6 Host MAY implement [RFC7278]
for delivering IPv6 prefixes on the LAN link.
13. Security
This section describes the specification for security for IPv6 nodes.
Achieving security in practice is a complex undertaking. Operational
procedures, protocols, key distribution mechanisms, certificate
management approaches, etc., are all components that impact the level
of security actually achieved in practice. More importantly,
deficiencies or a poor fit in any one individual component can
significantly reduce the overall effectiveness of a particular
security approach.
IPsec either can provide end-to-end security between nodes or or can
provide channel security (for example, via a site-to-site IPsec VPN),
making it possible to provide secure communication for all (or a
subset of) communication flows at the IP layer between pairs of
internet nodes. IPsec has two standard operating modes, Tunnel-mode
and Transport-mode. In Tunnel-mode, IPsec provides network-layer
security and protects an entire IP packet by encapsulating the
orginal IP packet and then pre-pending a new IP header. In
Transport-mode, IPsec provides security for the transport-layer (and
above) by encapsulating only the transport-layer (and above) portion
of the IP packet (i.e., without adding a 2nd IP header).
Although IPsec can be used with manual keying in some cases, such
usage has limited applicability and is not recommended.
A range of security technologies and approaches proliferate today
(e.g., IPsec, Transport Layer Security (TLS), Secure SHell (SSH), TLS
VPNS, etc.) No one approach has emerged as an ideal technology for
all needs and environments. Moreover, IPsec is not viewed as the
ideal security technology in all cases and is unlikely to displace
the others.
Previously, IPv6 mandated implementation of IPsec and recommended the
key management approach of IKE. This document updates that
recommendation by making support of the IPsec Architecture [RFC4301]
a SHOULD for all IPv6 nodes. Note that the IPsec Architecture
requires (e.g., Section 4.5 of RFC 4301) the implementation of both
Chown, et al. Expires January 17, 2019 [Page 20]
Internet-Draft IPv6 Node Requirements July 2018
manual and automatic key management. Currently, the recommended
automated key management protocol to implement is IKEv2 [RFC7296].
This document recognizes that there exists a range of device types
and environments where approaches to security other than IPsec can be
justified. For example, special-purpose devices may support only a
very limited number or type of applications, and an application-
specific security approach may be sufficient for limited management
or configuration capabilities. Alternatively, some devices may run
on extremely constrained hardware (e.g., sensors) where the full
IPsec Architecture is not justified.
Because most common platforms now support IPv6 and have it enabled by
default, IPv6 security is an issue for networks that are ostensibly
IPv4-only; see [RFC7123] for guidance on this area.
13.1. Requirements
"Security Architecture for the Internet Protocol" [RFC4301] SHOULD be
supported by all IPv6 nodes. Note that the IPsec Architecture
requires (e.g., Section 4.5 of [RFC4301]) the implementation of both
manual and automatic key management. Currently, the default
automated key management protocol to implement is IKEv2. As required
in [RFC4301], IPv6 nodes implementing the IPsec Architecture MUST
implement ESP [RFC4303] and MAY implement AH [RFC4302].
13.2. Transforms and Algorithms
The current set of mandatory-to-implement algorithms for the IPsec
Architecture are defined in "Cryptographic Algorithm Implementation
Requirements For ESP and AH" [RFC8221]. IPv6 nodes implementing the
IPsec Architecture MUST conform to the requirements in [RFC8221].
Preferred cryptographic algorithms often change more frequently than
security protocols. Therefore, implementations MUST allow for
migration to new algorithms, as RFC 8221 is replaced or updated in
the future.
The current set of mandatory-to-implement algorithms for IKEv2 are
defined in "Cryptographic Algorithms for Use in the Internet Key
Exchange Version 2 (IKEv2)" [RFC8247]. IPv6 nodes implementing IKEv2
MUST conform to the requirements in [RFC8247] and/or any future
updates or replacements to [RFC8247].
14. Router-Specific Functionality
This section defines general host considerations for IPv6 nodes that
act as routers. Currently, this section does not discuss detailed
Chown, et al. Expires January 17, 2019 [Page 21]
Internet-Draft IPv6 Node Requirements July 2018
routing-specific requirements. For the case of typical home routers,
[RFC7084] defines basic requirements for customer edge routers.
14.1. IPv6 Router Alert Option - RFC 2711
The IPv6 Router Alert Option [RFC2711] is an optional IPv6 Hop-by-Hop
Header that is used in conjunction with some protocols (e.g., RSVP
[RFC2205] or Multicast Listener Discovery (MLDv2) [RFC3810]). The
Router Alert option will need to be implemented whenever such
protocols that mandate its use are implemented. See Section 5.11.
14.2. Neighbor Discovery for IPv6 - RFC 4861
Sending Router Advertisements and processing Router Solicitations
MUST be supported.
Section 7 of [RFC6275] includes some mobility-specific extensions to
Neighbor Discovery. Routers SHOULD implement Sections 7.3 and 7.5,
even if they do not implement Home Agent functionality.
14.3. Stateful Address Autoconfiguration (DHCPv6) - RFC 3315
A single DHCP server ([RFC3315] or [RFC4862]) can provide
configuration information to devices directly attached to a shared
link, as well as to devices located elsewhere within a site.
Communication between a client and a DHCP server located on different
links requires the use of DHCP relay agents on routers.
In simple deployments, consisting of a single router and either a
single LAN or multiple LANs attached to the single router, together
with a WAN connection, a DHCP server embedded within the router is
one common deployment scenario (e.g., [RFC7084]). There is no need
for relay agents in such scenarios.
In more complex deployment scenarios, such as within enterprise or
service provider networks, the use of DHCP requires some level of
configuration, in order to configure relay agents, DHCP servers, etc.
In such environments, the DHCP server might even be run on a
traditional server, rather than as part of a router.
Because of the wide range of deployment scenarios, support for DHCP
server functionality on routers is optional. However, routers
targeted for deployment within more complex scenarios (as described
above) SHOULD support relay agent functionality. Note that "Basic
Requirements for IPv6 Customer Edge Routers" [RFC7084] requires
implementation of a DHCPv6 server function in IPv6 Customer Edge (CE)
routers.
Chown, et al. Expires January 17, 2019 [Page 22]
Internet-Draft IPv6 Node Requirements July 2018
14.4. IPv6 Prefix Length Recommendation for Forwarding - BCP 198
Forwarding nodes MUST conform to BCP 198 [RFC7608] and thus IPv6
implementations of nodes that may forward packets MUST conform to the
rules specified in Section 5.1 of [RFC4632].
15. Constrained Devices
The target for this document is general IPv6 nodes. In this Section,
we briefly discuss considerations for constrained devices.
In the case of constrained nodes, with limited CPU, memory, bandwidth
or power, support for certain IPv6 functionality may need to be
considered due to those limitations. While the requirements of this
document are RECOMMENDED for all nodes, including constrained nodes,
compromises may need to be made in certain cases. Where such
compromises are made, the interoperability of devices should be
strongly considered, paticularly where this may impact other nodes on
the same link, e.g., only supporting MLDv1 will affect other nodes.
The IETF 6LowPAN (IPv6 over Low Power LWPAN) WG defined six RFCs,
including a general overview and problem statement ([RFC4919], the
means by which IPv6 packets are transmitted over IEEE 802.15.4
networks [RFC4944] and ND optimisations for that medium [RFC6775].
IPv6 nodes that are battery-powered SHOULD implement the
recommendations in [RFC7772].
16. IPv6 Node Management
Network management MAY be supported by IPv6 nodes. However, for IPv6
nodes that are embedded devices, network management may be the only
possible way of controlling these nodes.
Existing network management protocols include SNMP [RFC3411], NETCONF
[RFC6241] and RESTCONF [RFC8040].
16.1. Management Information Base (MIB) Modules
[RFC8096] clarifies the obsoleted status of various IPv6-specific MIB
modules.
The following two MIB modules SHOULD be supported by nodes that
support a Simple Network Management Protocol (SNMP) agent.
Chown, et al. Expires January 17, 2019 [Page 23]
Internet-Draft IPv6 Node Requirements July 2018
16.1.1. IP Forwarding Table MIB
The IP Forwarding Table MIB [RFC4292] SHOULD be supported by nodes
that support an SNMP agent.
16.1.2. Management Information Base for the Internet Protocol (IP)
The IP MIB [RFC4293] SHOULD be supported by nodes that support an
SNMP agent.
16.1.3. Interface MIB
The Interface MIB [RFC2863] SHOULD be supported by nodes the support
an SNMP agent.
16.2. YANG Data Models
The following YANG data models SHOULD be supported by nodes that
support a NETCONF or RESTCONF agent.
16.2.1. IP Management YANG Model
The IP Management YANG Model [I-D.ietf-netmod-rfc7277bis] SHOULD be
supported by nodes that support NETCONF or RESTCONF.
16.2.2. Interface Management YANG Model
The Interface Management YANG Model [I-D.ietf-netmod-rfc7223bis]
SHOULD be supported by nodes that support NETCONF or RESTCONF.
17. Security Considerations
This document does not directly affect the security of the Internet,
beyond the security considerations associated with the individual
protocols.
Security is also discussed in Section 13 above.
18. IANA Considerations
This document does not require any IANA actions.
19. Authors and Acknowledgments
Chown, et al. Expires January 17, 2019 [Page 24]
Internet-Draft IPv6 Node Requirements July 2018
19.1. Authors and Acknowledgments (Current Document)
For this version of the IPv6 Node Requirements document, the authors
would like to thank Brian Carpenter, Dave Thaler, Tom Herbert, Erik
Kline, Mohamed Boucadair, and Michayla Newcombe for their
contributions.
19.2. Authors and Acknowledgments from RFC 6434
Ed Jankiewicz and Thomas Narten were named authors of the previous
iteration of this document, RFC6434.
For this version of the document, the authors thanked Hitoshi Asaeda,
Brian Carpenter, Tim Chown, Ralph Droms, Sheila Frankel, Sam Hartman,
Bob Hinden, Paul Hoffman, Pekka Savola, Yaron Sheffer, and Dave
Thaler.
19.3. Authors and Acknowledgments from RFC 4294
The original version of this document (RFC 4294) was written by the
IPv6 Node Requirements design team, which had the following members:
Jari Arkko, Marc Blanchet, Samita Chakrabarti, Alain Durand, Gerard
Gastaud, Jun-ichiro Itojun Hagino, Atsushi Inoue, Masahiro Ishiyama,
John Loughney, Rajiv Raghunarayan, Shoichi Sakane, Dave Thaler, and
Juha Wiljakka.
The authors would like to thank Ran Atkinson, Jim Bound, Brian
Carpenter, Ralph Droms, Christian Huitema, Adam Machalek, Thomas
Narten, Juha Ollila, and Pekka Savola for their comments. Thanks to
Mark Andrews for comments and corrections on DNS text. Thanks to
Alfred Hoenes for tracking the updates to various RFCs.
20. Appendix: Changes from RFC 6434
There have been many editorial clarifications as well as significant
additions and updates. While this section highlights some of the
changes, readers should not rely on this section for a comprehensive
list of all changes.
1. Restructured sections
2. Added 6LoWPAN to link layers as it has some deployment.
3. Removed DOD IPv6 Profile as it hasn't been updated.
4. Updated to MLDv2 support to a MUST since nodes are restricted if
MLDv1 is used.
Chown, et al. Expires January 17, 2019 [Page 25]
Internet-Draft IPv6 Node Requirements July 2018
5. Require DNS RA Options so SLAAC-only devices can get DNS,
RFC8106 is a MUST.
6. Require RFC3646 DNS Options for DHCPv6 implementations.
7. Added RESTCONF and NETCONF as possible options to Network
management.
8. Added section on constrained devices.
9. Added text on RFC7934, address availability to hosts (SHOULD).
10. Added text on RFC7844, anonymity profiles for DHCPv6 clients.
11. mDNS and DNS-SD added as updated service discovery.
12. Added RFC8028 as a SHOULD as a method for solving multi-prefix
network
13. Added ECN RFC3168 as a SHOULD
14. Added reference to RFC7123 for Security over IPv4-only networks
15. Removed Jumbograms RFC2675 as they aren't deployed.
16. Updated Obseleted RFCs to the new version of the RFC including
2460, 1981, 7321, 4307
17. Added RFC7772 for power comsumptions considerations
18. Added why /64 boundries for more detail - RFC 7421
19. Added a Unique IPv6 Prefix per Host to support currently
deployed IPv6 networks
20. Clarified RFC7066 was snapshot for 3GPP
21. Updated 4191 as a MUST, SHOULD for Type C Host as it helps solve
multi-prefix problem
22. Removed IPv6 over ATM since there aren't many deployments
23. Added a note in Section 6.6 for RFC6724 Section 5.5/
24. Added MUST for BCP 198 for forwarding IPv6 packets
25. Added reference to RFC8064 for stable address creation.
Chown, et al. Expires January 17, 2019 [Page 26]
Internet-Draft IPv6 Node Requirements July 2018
26. Added text on protection from excessive EH options
27. Added text on dangers of 1280 MTU UDP, esp. wrt DNS traffic
28. Added text to clarify RFC8200 behaviour for unrecognized EHs or
unrecognized ULPs
29. Removed dated email addresses from design team acknowledgements
for RFC 4294.
21. Appendix: Changes from RFC 4294
There have been many editorial clarifications as well as significant
additions and updates. While this section highlights some of the
changes, readers should not rely on this section for a comprehensive
list of all changes.
1. Updated the Introduction to indicate that this document is an
applicability statement and is aimed at general nodes.
2. Significantly updated the section on Mobility protocols, adding
references and downgrading previous SHOULDs to MAYs.
3. Changed Sub-IP Layer section to just list relevant RFCs, and
added some more RFCs.
4. Added section on SEND (it is a MAY).
5. Revised section on Privacy Extensions [RFC4941] to add more
nuance to recommendation.
6. Completely revised IPsec/IKEv2 section, downgrading overall
recommendation to a SHOULD.
7. Upgraded recommendation of DHCPv6 to SHOULD.
8. Added background section on DHCP versus RA options, added SHOULD
recommendation for DNS configuration via RAs (RFC6106), and
cleaned up DHCP recommendations.
9. Added recommendation that routers implement Sections 7.3 and 7.5
of [RFC6275].
10. Added pointer to subnet clarification document [RFC5942].
11. Added text that "IPv6 Host-to-Router Load Sharing" [RFC4311]
SHOULD be implemented.
Chown, et al. Expires January 17, 2019 [Page 27]
Internet-Draft IPv6 Node Requirements July 2018
12. Added reference to [RFC5722] (Overlapping Fragments), and made
it a MUST to implement.
13. Made "A Recommendation for IPv6 Address Text Representation"
[RFC5952] a SHOULD.
14. Removed mention of "DNAME" from the discussion about [RFC3363].
15. Numerous updates to reflect newer versions of IPv6 documents,
including [RFC4443], [RFC4291], [RFC3596], and [RFC4213].
16. Removed discussion of "Managed" and "Other" flags in RAs. There
is no consensus at present on how to process these flags, and
discussion of their semantics was removed in the most recent
update of Stateless Address Autoconfiguration [RFC4862].
17. Added many more references to optional IPv6 documents.
18. Made "A Recommendation for IPv6 Address Text Representation"
[RFC5952] a SHOULD.
19. Added reference to [RFC5722] (Overlapping Fragments), and made
it a MUST to implement.
20. Updated MLD section to include reference to Lightweight MLD
[RFC5790].
21. Added SHOULD recommendation for "Default Router Preferences and
More-Specific Routes" [RFC4191].
22. Made "IPv6 Flow Label Specification" [RFC6437] a SHOULD.
22. References
22.1. Normative References
[RFC1034] Mockapetris, P., "Domain names - concepts and facilities",
STD 13, RFC 1034, DOI 10.17487/RFC1034, November 1987,
<https://www.rfc-editor.org/info/rfc1034>.
[RFC1035] Mockapetris, P., "Domain names - implementation and
specification", STD 13, RFC 1035, DOI 10.17487/RFC1035,
November 1987, <https://www.rfc-editor.org/info/rfc1035>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
Chown, et al. Expires January 17, 2019 [Page 28]
Internet-Draft IPv6 Node Requirements July 2018
[RFC2710] Deering, S., Fenner, W., and B. Haberman, "Multicast
Listener Discovery (MLD) for IPv6", RFC 2710,
DOI 10.17487/RFC2710, October 1999,
<https://www.rfc-editor.org/info/rfc2710>.
[RFC2711] Partridge, C. and A. Jackson, "IPv6 Router Alert Option",
RFC 2711, DOI 10.17487/RFC2711, October 1999,
<https://www.rfc-editor.org/info/rfc2711>.
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, DOI 10.17487/RFC2863, June 2000,
<https://www.rfc-editor.org/info/rfc2863>.
[RFC3168] Ramakrishnan, K., Floyd, S., and D. Black, "The Addition
of Explicit Congestion Notification (ECN) to IP",
RFC 3168, DOI 10.17487/RFC3168, September 2001,
<https://www.rfc-editor.org/info/rfc3168>.
[RFC3315] Droms, R., Ed., Bound, J., Volz, B., Lemon, T., Perkins,
C., and M. Carney, "Dynamic Host Configuration Protocol
for IPv6 (DHCPv6)", RFC 3315, DOI 10.17487/RFC3315, July
2003, <https://www.rfc-editor.org/info/rfc3315>.
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
Architecture for Describing Simple Network Management
Protocol (SNMP) Management Frameworks", STD 62, RFC 3411,
DOI 10.17487/RFC3411, December 2002,
<https://www.rfc-editor.org/info/rfc3411>.
[RFC3596] Thomson, S., Huitema, C., Ksinant, V., and M. Souissi,
"DNS Extensions to Support IP Version 6", STD 88,
RFC 3596, DOI 10.17487/RFC3596, October 2003,
<https://www.rfc-editor.org/info/rfc3596>.
[RFC3736] Droms, R., "Stateless Dynamic Host Configuration Protocol
(DHCP) Service for IPv6", RFC 3736, DOI 10.17487/RFC3736,
April 2004, <https://www.rfc-editor.org/info/rfc3736>.
[RFC3810] Vida, R., Ed. and L. Costa, Ed., "Multicast Listener
Discovery Version 2 (MLDv2) for IPv6", RFC 3810,
DOI 10.17487/RFC3810, June 2004,
<https://www.rfc-editor.org/info/rfc3810>.
[RFC4033] Arends, R., Austein, R., Larson, M., Massey, D., and S.
Rose, "DNS Security Introduction and Requirements",
RFC 4033, DOI 10.17487/RFC4033, March 2005,
<https://www.rfc-editor.org/info/rfc4033>.
Chown, et al. Expires January 17, 2019 [Page 29]
Internet-Draft IPv6 Node Requirements July 2018
[RFC4034] Arends, R., Austein, R., Larson, M., Massey, D., and S.
Rose, "Resource Records for the DNS Security Extensions",
RFC 4034, DOI 10.17487/RFC4034, March 2005,
<https://www.rfc-editor.org/info/rfc4034>.
[RFC4035] Arends, R., Austein, R., Larson, M., Massey, D., and S.
Rose, "Protocol Modifications for the DNS Security
Extensions", RFC 4035, DOI 10.17487/RFC4035, March 2005,
<https://www.rfc-editor.org/info/rfc4035>.
[RFC4213] Nordmark, E. and R. Gilligan, "Basic Transition Mechanisms
for IPv6 Hosts and Routers", RFC 4213,
DOI 10.17487/RFC4213, October 2005,
<https://www.rfc-editor.org/info/rfc4213>.
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, DOI 10.17487/RFC4291, February
2006, <https://www.rfc-editor.org/info/rfc4291>.
[RFC4292] Haberman, B., "IP Forwarding Table MIB", RFC 4292,
DOI 10.17487/RFC4292, April 2006,
<https://www.rfc-editor.org/info/rfc4292>.
[RFC4293] Routhier, S., Ed., "Management Information Base for the
Internet Protocol (IP)", RFC 4293, DOI 10.17487/RFC4293,
April 2006, <https://www.rfc-editor.org/info/rfc4293>.
[RFC4301] Kent, S. and K. Seo, "Security Architecture for the
Internet Protocol", RFC 4301, DOI 10.17487/RFC4301,
December 2005, <https://www.rfc-editor.org/info/rfc4301>.
[RFC4303] Kent, S., "IP Encapsulating Security Payload (ESP)",
RFC 4303, DOI 10.17487/RFC4303, December 2005,
<https://www.rfc-editor.org/info/rfc4303>.
[RFC4311] Hinden, R. and D. Thaler, "IPv6 Host-to-Router Load
Sharing", RFC 4311, DOI 10.17487/RFC4311, November 2005,
<https://www.rfc-editor.org/info/rfc4311>.
[RFC4443] Conta, A., Deering, S., and M. Gupta, Ed., "Internet
Control Message Protocol (ICMPv6) for the Internet
Protocol Version 6 (IPv6) Specification", STD 89,
RFC 4443, DOI 10.17487/RFC4443, March 2006,
<https://www.rfc-editor.org/info/rfc4443>.
[RFC4607] Holbrook, H. and B. Cain, "Source-Specific Multicast for
IP", RFC 4607, DOI 10.17487/RFC4607, August 2006,
<https://www.rfc-editor.org/info/rfc4607>.
Chown, et al. Expires January 17, 2019 [Page 30]
Internet-Draft IPv6 Node Requirements July 2018
[RFC4632] Fuller, V. and T. Li, "Classless Inter-domain Routing
(CIDR): The Internet Address Assignment and Aggregation
Plan", BCP 122, RFC 4632, DOI 10.17487/RFC4632, August
2006, <https://www.rfc-editor.org/info/rfc4632>.
[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
DOI 10.17487/RFC4861, September 2007,
<https://www.rfc-editor.org/info/rfc4861>.
[RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
Address Autoconfiguration", RFC 4862,
DOI 10.17487/RFC4862, September 2007,
<https://www.rfc-editor.org/info/rfc4862>.
[RFC4941] Narten, T., Draves, R., and S. Krishnan, "Privacy
Extensions for Stateless Address Autoconfiguration in
IPv6", RFC 4941, DOI 10.17487/RFC4941, September 2007,
<https://www.rfc-editor.org/info/rfc4941>.
[RFC5095] Abley, J., Savola, P., and G. Neville-Neil, "Deprecation
of Type 0 Routing Headers in IPv6", RFC 5095,
DOI 10.17487/RFC5095, December 2007,
<https://www.rfc-editor.org/info/rfc5095>.
[RFC5453] Krishnan, S., "Reserved IPv6 Interface Identifiers",
RFC 5453, DOI 10.17487/RFC5453, February 2009,
<https://www.rfc-editor.org/info/rfc5453>.
[RFC5722] Krishnan, S., "Handling of Overlapping IPv6 Fragments",
RFC 5722, DOI 10.17487/RFC5722, December 2009,
<https://www.rfc-editor.org/info/rfc5722>.
[RFC5790] Liu, H., Cao, W., and H. Asaeda, "Lightweight Internet
Group Management Protocol Version 3 (IGMPv3) and Multicast
Listener Discovery Version 2 (MLDv2) Protocols", RFC 5790,
DOI 10.17487/RFC5790, February 2010,
<https://www.rfc-editor.org/info/rfc5790>.
[RFC5942] Singh, H., Beebee, W., and E. Nordmark, "IPv6 Subnet
Model: The Relationship between Links and Subnet
Prefixes", RFC 5942, DOI 10.17487/RFC5942, July 2010,
<https://www.rfc-editor.org/info/rfc5942>.
[RFC5952] Kawamura, S. and M. Kawashima, "A Recommendation for IPv6
Address Text Representation", RFC 5952,
DOI 10.17487/RFC5952, August 2010,
<https://www.rfc-editor.org/info/rfc5952>.
Chown, et al. Expires January 17, 2019 [Page 31]
Internet-Draft IPv6 Node Requirements July 2018
[RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
<https://www.rfc-editor.org/info/rfc6241>.
[RFC6437] Amante, S., Carpenter, B., Jiang, S., and J. Rajahalme,
"IPv6 Flow Label Specification", RFC 6437,
DOI 10.17487/RFC6437, November 2011,
<https://www.rfc-editor.org/info/rfc6437>.
[RFC6564] Krishnan, S., Woodyatt, J., Kline, E., Hoagland, J., and
M. Bhatia, "A Uniform Format for IPv6 Extension Headers",
RFC 6564, DOI 10.17487/RFC6564, April 2012,
<https://www.rfc-editor.org/info/rfc6564>.
[RFC6724] Thaler, D., Ed., Draves, R., Matsumoto, A., and T. Chown,
"Default Address Selection for Internet Protocol Version 6
(IPv6)", RFC 6724, DOI 10.17487/RFC6724, September 2012,
<https://www.rfc-editor.org/info/rfc6724>.
[RFC6762] Cheshire, S. and M. Krochmal, "Multicast DNS", RFC 6762,
DOI 10.17487/RFC6762, February 2013,
<https://www.rfc-editor.org/info/rfc6762>.
[RFC6763] Cheshire, S. and M. Krochmal, "DNS-Based Service
Discovery", RFC 6763, DOI 10.17487/RFC6763, February 2013,
<https://www.rfc-editor.org/info/rfc6763>.
[RFC6775] Shelby, Z., Ed., Chakrabarti, S., Nordmark, E., and C.
Bormann, "Neighbor Discovery Optimization for IPv6 over
Low-Power Wireless Personal Area Networks (6LoWPANs)",
RFC 6775, DOI 10.17487/RFC6775, November 2012,
<https://www.rfc-editor.org/info/rfc6775>.
[RFC6891] Damas, J., Graff, M., and P. Vixie, "Extension Mechanisms
for DNS (EDNS(0))", STD 75, RFC 6891,
DOI 10.17487/RFC6891, April 2013,
<https://www.rfc-editor.org/info/rfc6891>.
[RFC6946] Gont, F., "Processing of IPv6 "Atomic" Fragments",
RFC 6946, DOI 10.17487/RFC6946, May 2013,
<https://www.rfc-editor.org/info/rfc6946>.
[RFC7045] Carpenter, B. and S. Jiang, "Transmission and Processing
of IPv6 Extension Headers", RFC 7045,
DOI 10.17487/RFC7045, December 2013,
<https://www.rfc-editor.org/info/rfc7045>.
Chown, et al. Expires January 17, 2019 [Page 32]
Internet-Draft IPv6 Node Requirements July 2018
[RFC7048] Nordmark, E. and I. Gashinsky, "Neighbor Unreachability
Detection Is Too Impatient", RFC 7048,
DOI 10.17487/RFC7048, January 2014,
<https://www.rfc-editor.org/info/rfc7048>.
[RFC7112] Gont, F., Manral, V., and R. Bonica, "Implications of
Oversized IPv6 Header Chains", RFC 7112,
DOI 10.17487/RFC7112, January 2014,
<https://www.rfc-editor.org/info/rfc7112>.
[RFC7217] Gont, F., "A Method for Generating Semantically Opaque
Interface Identifiers with IPv6 Stateless Address
Autoconfiguration (SLAAC)", RFC 7217,
DOI 10.17487/RFC7217, April 2014,
<https://www.rfc-editor.org/info/rfc7217>.
[I-D.ietf-netmod-rfc7223bis]
Bjorklund, M., "A YANG Data Model for Interface
Management", draft-ietf-netmod-rfc7223bis-03 (work in
progress), January 2018.
[I-D.ietf-netmod-rfc7277bis]
Bjorklund, M., "A YANG Data Model for IP Management",
draft-ietf-netmod-rfc7277bis-03 (work in progress),
January 2018.
[RFC7296] Kaufman, C., Hoffman, P., Nir, Y., Eronen, P., and T.
Kivinen, "Internet Key Exchange Protocol Version 2
(IKEv2)", STD 79, RFC 7296, DOI 10.17487/RFC7296, October
2014, <https://www.rfc-editor.org/info/rfc7296>.
[RFC7527] Asati, R., Singh, H., Beebee, W., Pignataro, C., Dart, E.,
and W. George, "Enhanced Duplicate Address Detection",
RFC 7527, DOI 10.17487/RFC7527, April 2015,
<https://www.rfc-editor.org/info/rfc7527>.
[RFC7559] Krishnan, S., Anipko, D., and D. Thaler, "Packet-Loss
Resiliency for Router Solicitations", RFC 7559,
DOI 10.17487/RFC7559, May 2015,
<https://www.rfc-editor.org/info/rfc7559>.
[RFC7608] Boucadair, M., Petrescu, A., and F. Baker, "IPv6 Prefix
Length Recommendation for Forwarding", BCP 198, RFC 7608,
DOI 10.17487/RFC7608, July 2015,
<https://www.rfc-editor.org/info/rfc7608>.
Chown, et al. Expires January 17, 2019 [Page 33]
Internet-Draft IPv6 Node Requirements July 2018
[RFC8021] Gont, F., Liu, W., and T. Anderson, "Generation of IPv6
Atomic Fragments Considered Harmful", RFC 8021,
DOI 10.17487/RFC8021, January 2017,
<https://www.rfc-editor.org/info/rfc8021>.
[RFC8028] Baker, F. and B. Carpenter, "First-Hop Router Selection by
Hosts in a Multi-Prefix Network", RFC 8028,
DOI 10.17487/RFC8028, November 2016,
<https://www.rfc-editor.org/info/rfc8028>.
[RFC8040] Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
<https://www.rfc-editor.org/info/rfc8040>.
[RFC8064] Gont, F., Cooper, A., Thaler, D., and W. Liu,
"Recommendation on Stable IPv6 Interface Identifiers",
RFC 8064, DOI 10.17487/RFC8064, February 2017,
<https://www.rfc-editor.org/info/rfc8064>.
[RFC8106] Jeong, J., Park, S., Beloeil, L., and S. Madanapalli,
"IPv6 Router Advertisement Options for DNS Configuration",
RFC 8106, DOI 10.17487/RFC8106, March 2017,
<https://www.rfc-editor.org/info/rfc8106>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8200] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", STD 86, RFC 8200,
DOI 10.17487/RFC8200, July 2017,
<https://www.rfc-editor.org/info/rfc8200>.
[RFC8201] McCann, J., Deering, S., Mogul, J., and R. Hinden, Ed.,
"Path MTU Discovery for IP version 6", STD 87, RFC 8201,
DOI 10.17487/RFC8201, July 2017,
<https://www.rfc-editor.org/info/rfc8201>.
[RFC8221] Wouters, P., Migault, D., Mattsson, J., Nir, Y., and T.
Kivinen, "Cryptographic Algorithm Implementation
Requirements and Usage Guidance for Encapsulating Security
Payload (ESP) and Authentication Header (AH)", RFC 8221,
DOI 10.17487/RFC8221, October 2017,
<https://www.rfc-editor.org/info/rfc8221>.
Chown, et al. Expires January 17, 2019 [Page 34]
Internet-Draft IPv6 Node Requirements July 2018
[RFC8247] Nir, Y., Kivinen, T., Wouters, P., and D. Migault,
"Algorithm Implementation Requirements and Usage Guidance
for the Internet Key Exchange Protocol Version 2 (IKEv2)",
RFC 8247, DOI 10.17487/RFC8247, September 2017,
<https://www.rfc-editor.org/info/rfc8247>.
22.2. Informative References
[RFC0793] Postel, J., "Transmission Control Protocol", STD 7,
RFC 793, DOI 10.17487/RFC0793, September 1981,
<https://www.rfc-editor.org/info/rfc793>.
[RFC2205] Braden, R., Ed., Zhang, L., Berson, S., Herzog, S., and S.
Jamin, "Resource ReSerVation Protocol (RSVP) -- Version 1
Functional Specification", RFC 2205, DOI 10.17487/RFC2205,
September 1997, <https://www.rfc-editor.org/info/rfc2205>.
[RFC2464] Crawford, M., "Transmission of IPv6 Packets over Ethernet
Networks", RFC 2464, DOI 10.17487/RFC2464, December 1998,
<https://www.rfc-editor.org/info/rfc2464>.
[RFC2491] Armitage, G., Schulter, P., Jork, M., and G. Harter, "IPv6
over Non-Broadcast Multiple Access (NBMA) networks",
RFC 2491, DOI 10.17487/RFC2491, January 1999,
<https://www.rfc-editor.org/info/rfc2491>.
[RFC2590] Conta, A., Malis, A., and M. Mueller, "Transmission of
IPv6 Packets over Frame Relay Networks Specification",
RFC 2590, DOI 10.17487/RFC2590, May 1999,
<https://www.rfc-editor.org/info/rfc2590>.
[RFC2923] Lahey, K., "TCP Problems with Path MTU Discovery",
RFC 2923, DOI 10.17487/RFC2923, September 2000,
<https://www.rfc-editor.org/info/rfc2923>.
[RFC3146] Fujisawa, K. and A. Onoe, "Transmission of IPv6 Packets
over IEEE 1394 Networks", RFC 3146, DOI 10.17487/RFC3146,
October 2001, <https://www.rfc-editor.org/info/rfc3146>.
[RFC3363] Bush, R., Durand, A., Fink, B., Gudmundsson, O., and T.
Hain, "Representing Internet Protocol version 6 (IPv6)
Addresses in the Domain Name System (DNS)", RFC 3363,
DOI 10.17487/RFC3363, August 2002,
<https://www.rfc-editor.org/info/rfc3363>.
Chown, et al. Expires January 17, 2019 [Page 35]
Internet-Draft IPv6 Node Requirements July 2018
[RFC3493] Gilligan, R., Thomson, S., Bound, J., McCann, J., and W.
Stevens, "Basic Socket Interface Extensions for IPv6",
RFC 3493, DOI 10.17487/RFC3493, February 2003,
<https://www.rfc-editor.org/info/rfc3493>.
[RFC3542] Stevens, W., Thomas, M., Nordmark, E., and T. Jinmei,
"Advanced Sockets Application Program Interface (API) for
IPv6", RFC 3542, DOI 10.17487/RFC3542, May 2003,
<https://www.rfc-editor.org/info/rfc3542>.
[RFC3646] Droms, R., Ed., "DNS Configuration options for Dynamic
Host Configuration Protocol for IPv6 (DHCPv6)", RFC 3646,
DOI 10.17487/RFC3646, December 2003,
<https://www.rfc-editor.org/info/rfc3646>.
[RFC3678] Thaler, D., Fenner, B., and B. Quinn, "Socket Interface
Extensions for Multicast Source Filters", RFC 3678,
DOI 10.17487/RFC3678, January 2004,
<https://www.rfc-editor.org/info/rfc3678>.
[RFC6275] Perkins, C., Ed., Johnson, D., and J. Arkko, "Mobility
Support in IPv6", RFC 6275, DOI 10.17487/RFC6275, July
2011, <https://www.rfc-editor.org/info/rfc6275>.
[RFC3776] Arkko, J., Devarapalli, V., and F. Dupont, "Using IPsec to
Protect Mobile IPv6 Signaling Between Mobile Nodes and
Home Agents", RFC 3776, DOI 10.17487/RFC3776, June 2004,
<https://www.rfc-editor.org/info/rfc3776>.
[RFC3971] Arkko, J., Ed., Kempf, J., Zill, B., and P. Nikander,
"SEcure Neighbor Discovery (SEND)", RFC 3971,
DOI 10.17487/RFC3971, March 2005,
<https://www.rfc-editor.org/info/rfc3971>.
[RFC3972] Aura, T., "Cryptographically Generated Addresses (CGA)",
RFC 3972, DOI 10.17487/RFC3972, March 2005,
<https://www.rfc-editor.org/info/rfc3972>.
[RFC4191] Draves, R. and D. Thaler, "Default Router Preferences and
More-Specific Routes", RFC 4191, DOI 10.17487/RFC4191,
November 2005, <https://www.rfc-editor.org/info/rfc4191>.
[RFC4302] Kent, S., "IP Authentication Header", RFC 4302,
DOI 10.17487/RFC4302, December 2005,
<https://www.rfc-editor.org/info/rfc4302>.
Chown, et al. Expires January 17, 2019 [Page 36]
Internet-Draft IPv6 Node Requirements July 2018
[RFC4338] DeSanti, C., Carlson, C., and R. Nixon, "Transmission of
IPv6, IPv4, and Address Resolution Protocol (ARP) Packets
over Fibre Channel", RFC 4338, DOI 10.17487/RFC4338,
January 2006, <https://www.rfc-editor.org/info/rfc4338>.
[RFC4380] Huitema, C., "Teredo: Tunneling IPv6 over UDP through
Network Address Translations (NATs)", RFC 4380,
DOI 10.17487/RFC4380, February 2006,
<https://www.rfc-editor.org/info/rfc4380>.
[RFC4429] Moore, N., "Optimistic Duplicate Address Detection (DAD)
for IPv6", RFC 4429, DOI 10.17487/RFC4429, April 2006,
<https://www.rfc-editor.org/info/rfc4429>.
[RFC4584] Chakrabarti, S. and E. Nordmark, "Extension to Sockets API
for Mobile IPv6", RFC 4584, DOI 10.17487/RFC4584, July
2006, <https://www.rfc-editor.org/info/rfc4584>.
[RFC4821] Mathis, M. and J. Heffner, "Packetization Layer Path MTU
Discovery", RFC 4821, DOI 10.17487/RFC4821, March 2007,
<https://www.rfc-editor.org/info/rfc4821>.
[RFC4877] Devarapalli, V. and F. Dupont, "Mobile IPv6 Operation with
IKEv2 and the Revised IPsec Architecture", RFC 4877,
DOI 10.17487/RFC4877, April 2007,
<https://www.rfc-editor.org/info/rfc4877>.
[RFC4884] Bonica, R., Gan, D., Tappan, D., and C. Pignataro,
"Extended ICMP to Support Multi-Part Messages", RFC 4884,
DOI 10.17487/RFC4884, April 2007,
<https://www.rfc-editor.org/info/rfc4884>.
[RFC4890] Davies, E. and J. Mohacsi, "Recommendations for Filtering
ICMPv6 Messages in Firewalls", RFC 4890,
DOI 10.17487/RFC4890, May 2007,
<https://www.rfc-editor.org/info/rfc4890>.
[RFC4919] Kushalnagar, N., Montenegro, G., and C. Schumacher, "IPv6
over Low-Power Wireless Personal Area Networks (6LoWPANs):
Overview, Assumptions, Problem Statement, and Goals",
RFC 4919, DOI 10.17487/RFC4919, August 2007,
<https://www.rfc-editor.org/info/rfc4919>.
[RFC4944] Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler,
"Transmission of IPv6 Packets over IEEE 802.15.4
Networks", RFC 4944, DOI 10.17487/RFC4944, September 2007,
<https://www.rfc-editor.org/info/rfc4944>.
Chown, et al. Expires January 17, 2019 [Page 37]
Internet-Draft IPv6 Node Requirements July 2018
[RFC5014] Nordmark, E., Chakrabarti, S., and J. Laganier, "IPv6
Socket API for Source Address Selection", RFC 5014,
DOI 10.17487/RFC5014, September 2007,
<https://www.rfc-editor.org/info/rfc5014>.
[RFC5072] Varada, S., Ed., Haskins, D., and E. Allen, "IP Version 6
over PPP", RFC 5072, DOI 10.17487/RFC5072, September 2007,
<https://www.rfc-editor.org/info/rfc5072>.
[RFC5121] Patil, B., Xia, F., Sarikaya, B., Choi, JH., and S.
Madanapalli, "Transmission of IPv6 via the IPv6
Convergence Sublayer over IEEE 802.16 Networks", RFC 5121,
DOI 10.17487/RFC5121, February 2008,
<https://www.rfc-editor.org/info/rfc5121>.
[RFC5555] Soliman, H., Ed., "Mobile IPv6 Support for Dual Stack
Hosts and Routers", RFC 5555, DOI 10.17487/RFC5555, June
2009, <https://www.rfc-editor.org/info/rfc5555>.
[RFC6563] Jiang, S., Conrad, D., and B. Carpenter, "Moving A6 to
Historic Status", RFC 6563, DOI 10.17487/RFC6563, March
2012, <https://www.rfc-editor.org/info/rfc6563>.
[RFC7066] Korhonen, J., Ed., Arkko, J., Ed., Savolainen, T., and S.
Krishnan, "IPv6 for Third Generation Partnership Project
(3GPP) Cellular Hosts", RFC 7066, DOI 10.17487/RFC7066,
November 2013, <https://www.rfc-editor.org/info/rfc7066>.
[RFC7084] Singh, H., Beebee, W., Donley, C., and B. Stark, "Basic
Requirements for IPv6 Customer Edge Routers", RFC 7084,
DOI 10.17487/RFC7084, November 2013,
<https://www.rfc-editor.org/info/rfc7084>.
[RFC7123] Gont, F. and W. Liu, "Security Implications of IPv6 on
IPv4 Networks", RFC 7123, DOI 10.17487/RFC7123, February
2014, <https://www.rfc-editor.org/info/rfc7123>.
[RFC7278] Byrne, C., Drown, D., and A. Vizdal, "Extending an IPv6
/64 Prefix from a Third Generation Partnership Project
(3GPP) Mobile Interface to a LAN Link", RFC 7278,
DOI 10.17487/RFC7278, June 2014,
<https://www.rfc-editor.org/info/rfc7278>.
[RFC7371] Boucadair, M. and S. Venaas, "Updates to the IPv6
Multicast Addressing Architecture", RFC 7371,
DOI 10.17487/RFC7371, September 2014,
<https://www.rfc-editor.org/info/rfc7371>.
Chown, et al. Expires January 17, 2019 [Page 38]
Internet-Draft IPv6 Node Requirements July 2018
[RFC7421] Carpenter, B., Ed., Chown, T., Gont, F., Jiang, S.,
Petrescu, A., and A. Yourtchenko, "Analysis of the 64-bit
Boundary in IPv6 Addressing", RFC 7421,
DOI 10.17487/RFC7421, January 2015,
<https://www.rfc-editor.org/info/rfc7421>.
[RFC7721] Cooper, A., Gont, F., and D. Thaler, "Security and Privacy
Considerations for IPv6 Address Generation Mechanisms",
RFC 7721, DOI 10.17487/RFC7721, March 2016,
<https://www.rfc-editor.org/info/rfc7721>.
[RFC7739] Gont, F., "Security Implications of Predictable Fragment
Identification Values", RFC 7739, DOI 10.17487/RFC7739,
February 2016, <https://www.rfc-editor.org/info/rfc7739>.
[RFC7772] Yourtchenko, A. and L. Colitti, "Reducing Energy
Consumption of Router Advertisements", BCP 202, RFC 7772,
DOI 10.17487/RFC7772, February 2016,
<https://www.rfc-editor.org/info/rfc7772>.
[RFC7844] Huitema, C., Mrugalski, T., and S. Krishnan, "Anonymity
Profiles for DHCP Clients", RFC 7844,
DOI 10.17487/RFC7844, May 2016,
<https://www.rfc-editor.org/info/rfc7844>.
[RFC7934] Colitti, L., Cerf, V., Cheshire, S., and D. Schinazi,
"Host Address Availability Recommendations", BCP 204,
RFC 7934, DOI 10.17487/RFC7934, July 2016,
<https://www.rfc-editor.org/info/rfc7934>.
[RFC8087] Fairhurst, G. and M. Welzl, "The Benefits of Using
Explicit Congestion Notification (ECN)", RFC 8087,
DOI 10.17487/RFC8087, March 2017,
<https://www.rfc-editor.org/info/rfc8087>.
[RFC8096] Fenner, B., "The IPv6-Specific MIB Modules Are Obsolete",
RFC 8096, DOI 10.17487/RFC8096, April 2017,
<https://www.rfc-editor.org/info/rfc8096>.
[RFC8273] Brzozowski, J. and G. Van de Velde, "Unique IPv6 Prefix
per Host", RFC 8273, DOI 10.17487/RFC8273, December 2017,
<https://www.rfc-editor.org/info/rfc8273>.
[POSIX] IEEE, "IEEE Std. 1003.1-2008 Standard for Information
Technology -- Portable Operating System Interface (POSIX),
ISO/IEC 9945:2009", <http://www.ieee.org>.
Chown, et al. Expires January 17, 2019 [Page 39]
Internet-Draft IPv6 Node Requirements July 2018
[USGv6] National Institute of Standards and Technology, "A Profile
for IPv6 in the U.S. Government - Version 1.0", July 2008,
<https://doi.org/10.6028/NIST.SP.500-267Ar1>.
Authors' Addresses
Tim Chown
Jisc
Lumen House, Library Avenue
Harwell Oxford, Didcot OX11 0SG
United Kingdom
Email: tim.chown@jisc.ac.uk
John Loughney
Intel
Santa Clara, CA
USA
Email: john.loughney@gmail.com
Timothy Winters
University of New Hampshire, Interoperability Lab (UNH-IOL)
Durham, NH
United States
Email: twinters@iol.unh.edu
Chown, et al. Expires January 17, 2019 [Page 40]
