Internet DRAFT - draft-ietf-6man-ug
draft-ietf-6man-ug
6MAN B. Carpenter
Internet-Draft Univ. of Auckland
Updates: 4291 (if approved) S. Jiang
Intended status: Standards Track Huawei Technologies Co., Ltd
Expires: June 5, 2014 December 2, 2013
Significance of IPv6 Interface Identifiers
draft-ietf-6man-ug-06
Abstract
The IPv6 addressing architecture includes a unicast interface
identifier that is used in the creation of many IPv6 addresses.
Interface identifiers are formed by a variety of methods. This
document clarifies that the bits in an interface identifier have no
meaning and that the entire identifier should be treated as an opaque
value. In particular, RFC 4291 defines a method by which the
Universal and Group bits of an IEEE link-layer address are mapped
into an IPv6 unicast interface identifier. This document clarifies
that those two bits are significant only in the process of deriving
interface identifiers from an IEEE link-layer address, and updates
RFC 4291 accordingly.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on June 5, 2014.
Copyright Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
Carpenter & Jiang Expires June 5, 2014 [Page 1]
Internet-Draft IPv6 IID significance December 2013
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3
2. Problem statement . . . . . . . . . . . . . . . . . . . . . . 3
3. Usefulness of the U and G Bits . . . . . . . . . . . . . . . 5
4. The Role of Duplicate Address Detection . . . . . . . . . . . 6
5. Clarification of Specifications . . . . . . . . . . . . . . . 6
6. Security Considerations . . . . . . . . . . . . . . . . . . . 7
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 8
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 8
9. Change log [RFC Editor: Please remove] . . . . . . . . . . . 8
10. References . . . . . . . . . . . . . . . . . . . . . . . . . 9
10.1. Normative References . . . . . . . . . . . . . . . . . . 9
10.2. Informative References . . . . . . . . . . . . . . . . . 9
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 11
1. Introduction
IPv6 unicast addresses consist of a prefix followed by an Interface
Identifier (IID). The IID is supposed to be unique on the links
reached by routing to that prefix, giving an IPv6 address that is
unique within the applicable scope (link local or global). According
to the IPv6 addressing architecture [RFC4291], when a 64-bit IPv6
unicast IID is formed on the basis of an IEEE EUI-64 address, usually
itself expanded from a 48-bit MAC address, a particular format must
be used:
"For all unicast addresses, except those that start with the binary
value 000, Interface IDs are required to be 64 bits long and to be
constructed in Modified EUI-64 format."
Thus the specification assumes that the normal case is to transform
an Ethernet-style address into an IID, but in practice, there are
various methods of forming such an interface identifier.
The Modified EUI-64 format preserves the information provided by two
particular bits in the MAC address:
Carpenter & Jiang Expires June 5, 2014 [Page 2]
Internet-Draft IPv6 IID significance December 2013
o The "u/l" bit in a MAC address [IEEE802] is set to 0 to indicate
universal scope (implying uniqueness) or to 1 to indicate local
scope (without implying uniqueness). In an IID formed from a MAC
address, this bit is simply known as the "u" bit and its value is
inverted, i.e., 1 for universal scope and 0 for local scope.
According to RFC 4291 and [RFC7042], the reason for this was to
make it easier for network operators to manually configure local-
scope IIDs.
In an IID, this bit is in position 6, i.e., position 70 in the
complete IPv6 address.
o The "i/g" bit in a MAC address is set to 1 to indicate group
addressing (link-layer multicast). The value of this bit is
preserved in an IID, where it is known as the "g" bit.
In an IID, this bit is in position 7, i.e., position 71 in the
complete IPv6 address.
This document discusses problems observed with the "u" and "g" bits
as a result of the above requirements and the fact that various other
methods of forming an IID have been defined, quite independently of
the method described in Appendix A of RFC 4291. It then discusses
the usefulness of these two bits and the significance of the bits in
an IID in general. Finally, it updates RFC 4291 accordingly.
1.1. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
2. Problem statement
In addition to IIDs formed from IEEE EUI-64 addresses, various new
forms of IID have been defined, including temporary addresses
[RFC4941], Cryptographically Generated Addresses (CGAs) [RFC3972]
[RFC4982], Hash-Based Addresses (HBAs) [RFC5535], and ISATAP
addresses [RFC5214]. Other methods have been proposed, such as
stable privacy addresses [I-D.ietf-6man-stable-privacy-addresses],
and mapped addresses for 4rd [I-D.ietf-softwire-4rd]. In each case,
the question of how to set the "u" and "g" bits has to be decided.
For example, RFC 3972 specifies that they are both zero in CGAs, and
RFC 4982 describes them as if they were reserved bits. The same
applies to HBAs. On the other hand, RFC 4941 specifies that "u" must
be zero but leaves "g" variable. The NAT64 addressing format
[RFC6052] sets the whole byte containing "u" and "g" to zero.
Carpenter & Jiang Expires June 5, 2014 [Page 3]
Internet-Draft IPv6 IID significance December 2013
Another case where the "u" and "g" bits are specified is in the
Reserved IPv6 Subnet Anycast Address format [RFC2526], which states
that "for interface identifiers in EUI-64 format, the universal/local
bit in the interface identifier MUST be set to 0" (i.e., local) and
requires that "g" bit to be set to 1. However, the text neither
states nor implies any semantics for these bits in anycast addresses.
A common operational practice for well-known servers is to manually
assign a small number as the IID, in which case "u" and "g" are both
zero.
These cases illustrate that the statement quoted above from RFC 4291
requiring "Modified EUI-64 format" is inapplicable when applied to
forms of IID that are not in fact based on an underlying EUI-64
address. In practice, the IETF has chosen to assign some 64-bit IIDs
that have nothing to do with EUI-64.
A particular case is that of /127 prefixes for point-to-point links
between routers, as standardised by [RFC6164]. The addresses on
these links are undoubtedly global unicast addresses, but they do not
have a 64-bit IID. The bits in the positions named "u" and "g" in
such an IID have no special significance and their values are not
specified.
Each time a new IID format is proposed, the question arises whether
these bits have any meaning. Section 2.2.1 of RFC 7042 discusses the
mechanics of the bit allocations but does not explain the purpose or
usefulness of these bits in an IID. There is an IANA registry for
reserved IID values [RFC5453] but again there is no explanation of
the purpose of the "u" and "g" bits.
There was a presumption when IPv6 was designed and the IID format was
first specified that a universally unique IID might prove to be very
useful, for example to contribute to solving the multihoming problem.
Indeed, the addressing architecture [RFC4291] states this explicitly:
"The use of the universal/local bit in the Modified EUI-64 format
identifier is to allow development of future technology that can take
advantage of interface identifiers with universal scope."
However, this has not so far proved to be the case. Also, there is
evidence from the field that MAC addresses with universal scope are
sometimes assigned to multiple MAC interfaces. There are recurrent
reports of manufacturers assigning the same MAC address to multiple
devices, and significant re-use of the same virtual MAC address is
reported in virtual machine environments. Once transformed into IID
format (with "u" = 1) these identifiers would purport to be
universally unique but would in fact be ambiguous. This has no known
Carpenter & Jiang Expires June 5, 2014 [Page 4]
Internet-Draft IPv6 IID significance December 2013
harmful effect as long as the replicated MAC addresses and IIDs are
used on different layer 2 links. If they are used on the same link,
of course there will be a problem, very likely interfering with link-
layer transmission. If not, the problem will be detected by
duplicate address detection [RFC4862] [RFC6775], but such an error
can usually only be resolved by human intervention.
The conclusion from this is that the "u" bit is not a reliable
indicator of universal uniqueness.
We note that Identifier-Locator Network Protocol (ILNP), a
multihoming solution that might be expected to benefit from
universally unique IIDs in modified EUI-64 format, does not in fact
rely on them. ILNP uses its own format, defined as a Node Identifier
[RFC6741]. ILNP has the constraint that a given Node Identifier must
be unique within the context of a given Locator (i.e. within a single
given IPv6 subnetwork). As we have just shown, the state of the "u"
bit does not in any way guarantee such uniqueness, but duplicate
address detection is available.
Thus, we can conclude that the value of the "u" bit in IIDs has no
particular meaning. In the case of an IID created from a MAC address
according to RFC 4291, its value is determined by the MAC address,
but that is all.
An IPv6 IID should not be created from a MAC group address, so the
"g" bit will normally be zero, but this value also has no particular
meaning. Additionally, the "u" and the "g" bits are both meaningless
in the format of an IPv6 multicast group ID [RFC3306] [RFC3307].
None of the above implies that there is a problem with using the "u"
and "g" bits in MAC addresses as part of the process of generating
IIDs from MAC addresses, or with specifying their values in other
methods of generating IIDs. What it does imply is that, after an IID
is generated by any method, no reliable deductions can be made from
the state of the "u" and "g" bits; in other words, these bits have no
useful semantics in an IID.
Once this is recognised, we can avoid the problematic confusion
caused by these bits each time that a new form of IID is proposed.
3. Usefulness of the U and G Bits
Given that the "u" and "g" bits do not have a reliable meaning in an
IID, it is relevant to consider what usefulness they do have.
If an IID is known or guessed to have been created according to RFC
4291, it could be transformed back into a MAC address. This can be
Carpenter & Jiang Expires June 5, 2014 [Page 5]
Internet-Draft IPv6 IID significance December 2013
very helpful during operational fault diagnosis. For that reason,
mapping the IEEE "u" and "g" bits into the IID has operational
usefulness. However, it should be stressed that an IID with "u" = 1
and "g" = 0 might not be formed from a MAC address; on the contrary,
it might equally result from another method. With other methods,
there is no reverse transformation available.
Given that the values of the "u" and "g" bits in an IID have no
particular meaning, new methods of IID formation are at liberty to
use them as they wish, for example as additional pseudo-random bits
to reduce the chances of duplicate IIDs.
4. The Role of Duplicate Address Detection
As mentioned above, Duplicate Address Detection (DAD) [RFC4862] is
able to detect any case where a collision of two IIDs on the same
link leads to a duplicated IPv6 address. The scope of DAD may be
extended to a set of links by a DAD proxy [RFC6957] or by Neighbor
Discovery Optimization [RFC6775]. Since DAD is mandatory for all
nodes, there will be almost no case in which an IID collision,
however unlikely it may be, is not detected. It is out of scope of
most existing specifications to define the recovery action after a
DAD failure, which is an implementation issue. If a manually created
IID, or an IID derived from a MAC address according to RFC 4291,
leads to a DAD failure, human intervention will most likely be
required. However, as mentioned above, some methods of IID formation
might produce IID values with "u" = 1 and "g" = 0 that are not based
on a MAC address. With very low probability, such a value might
collide with an IID based on a MAC address.
As stated in RFC 4862:
"On the other hand, if the duplicate link-local address is not formed
from an interface identifier based on the hardware address, which is
supposed to be uniquely assigned, IP operation on the interface MAY
be continued."
Continued operation is only possible if a new IID is created. The
best procedure to follow for this will depend on the IID formation
method in use. For example, if an IID is formed by a pseudo-random
process, that process could simply be repeated.
5. Clarification of Specifications
This section describes clarifications to the IPv6 specifications that
result from the above discussion. Their aim is to reduce confusion
while retaining the useful aspects of the "u" and "g" bits in IIDs.
Carpenter & Jiang Expires June 5, 2014 [Page 6]
Internet-Draft IPv6 IID significance December 2013
The EUI-64 to IID transformation defined in the IPv6 addressing
architecture [RFC4291] MUST be used for all cases where an IPv6 IID
is derived from an IEEE MAC or EUI-64 address. With any other form
of link layer address, an equivalent transformation SHOULD be used.
Specifications of other forms of 64-bit IID MUST specify how all 64
bits are set, but a generic semantic meaning for the "u" and "g" bits
MUST NOT be defined. However, the method of generating IIDs for
specific link types MAY define some local significance for certain
bits.
In all cases, the bits in an IID have no generic semantics; in other
words, they have opaque values. In fact, the whole IID value MUST be
viewed as an opaque bit string by third parties, except possibly in
the local context.
The following statement in section 2.5.1 of the IPv6 addressing
architecture [RFC4291]:
"For all unicast addresses, except those that start with the binary
value 000, Interface IDs are required to be 64 bits long and to be
constructed in Modified EUI-64 format."
is replaced by:
"For all unicast addresses, except those that start with the binary
value 000, Interface IDs are required to be 64 bits long. If derived
from an IEEE MAC-layer address, they must be constructed in Modified
EUI-64 format."
The following statement in section 2.5.1 of the IPv6 addressing
architecture [RFC4291] is obsoleted:
"The use of the universal/local bit in the Modified EUI-64 format
identifier is to allow development of future technology that can take
advantage of interface identifiers with universal scope."
As far as is known, no existing implementation will be affected by
these changes. The benefit is that future design discussions are
simplified.
6. Security Considerations
No new security exposures or issues are raised by this document.
In some contexts, unpredictable IID values are considered beneficial
to enhance privacy and defeat scanning attacks. The recognition that
the IID value should be regarded as an opaque bit string is
Carpenter & Jiang Expires June 5, 2014 [Page 7]
Internet-Draft IPv6 IID significance December 2013
consistent with methods of IID formation that result in
unpredictable, pseudo-random values.
7. IANA Considerations
This document requests no immediate action by IANA. However, the
following should be noted when considering any future proposed
addition to the registry of reserved IID values, which requires
Standards Action according to [RFC5453].
Full deployment of a new reserved IID value would require updates to
IID generation code in every deployed IPv6 stack, so the technical
justification for such a Standards Action would need to be extremely
strong.
The preceding sentence and a reference to this document should be
added to the Reserved IPv6 Interface Identifiers registry.
8. Acknowledgements
Valuable comments were received from Ran Atkinson, Remi Despres,
Ralph Droms, Fernando Gont, Eric Gray, Brian Haberman, Joel Halpern,
Bob Hinden, Christian Huitema, Ray Hunter, Tatuya Jinmei, Roger
Jorgensen, Mark Smith, Bernie Volz and other participants in the 6MAN
working group.
Brian Carpenter was a visitor at the Computer Laboratory, Cambridge
University during part of this work.
This document was produced using the xml2rfc tool [RFC2629].
9. Change log [RFC Editor: Please remove]
draft-ietf-6man-ug-06: IETF Last Call comments - clarifications,
2013-12-02.
draft-ietf-6man-ug-05: AD comments - clarifications, 2013-11-14.
draft-ietf-6man-ug-04: corrected interpretation of 802.1, removed a
content-free paragraph, minor fixes, 2013-10-02.
draft-ietf-6man-ug-03: some clarifications, text on unpredictable
IIDs, minor corrections, 2013-08-26.
draft-ietf-6man-ug-02: incorporated WG Last Call comments: removed
open issue, clarified IEEE bit names, clarified DAD text, updated
references, minor editorial corrections, 2013-08-06.
Carpenter & Jiang Expires June 5, 2014 [Page 8]
Internet-Draft IPv6 IID significance December 2013
draft-ietf-6man-ug-01: emphasised "opaque" nature of IID, added text
about DAD failures, expanded IANA considerations, 2013-05-25.
draft-ietf-6man-ug-00: first WG version, text clarified, added
possibility of link-local significance, 2013-03-28.
draft-carpenter-6man-ug-01: numerous clarifications following WG
comments, discussed DAD, added new section on the usefulness of the u
/g bits, expanded IANA considerations, set intended status,
2013-02-21.
draft-carpenter-6man-ug-00: original version, 2013-01-31.
10. References
10.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, February 2006.
[RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
Address Autoconfiguration", RFC 4862, September 2007.
[RFC5453] Krishnan, S., "Reserved IPv6 Interface Identifiers", RFC
5453, February 2009.
[RFC7042] Eastlake, D. and J. Abley, "IANA Considerations and IETF
Protocol and Documentation Usage for IEEE 802 Parameters",
BCP 141, RFC 7042, October 2013.
10.2. Informative References
[I-D.ietf-6man-stable-privacy-addresses]
Gont, F., "A Method for Generating Semantically Opaque
Interface Identifiers with IPv6 Stateless Address
Autoconfiguration (SLAAC)", draft-ietf-6man-stable-
privacy-addresses-14 (work in progress), October 2013.
[I-D.ietf-softwire-4rd]
Despres, R., Jiang, S., Penno, R., Lee, Y., Chen, G., and
M. Chen, "IPv4 Residual Deployment via IPv6 - a Stateless
Solution (4rd)", draft-ietf-softwire-4rd-07 (work in
progress), October 2013.
Carpenter & Jiang Expires June 5, 2014 [Page 9]
Internet-Draft IPv6 IID significance December 2013
[IEEE802] , "IEEE Standard for Local and Metropolitan Area Networks:
Overview and Architecture", IEEE Std 802-2001 (R2007),
2007.
[RFC2526] Johnson, D. and S. Deering, "Reserved IPv6 Subnet Anycast
Addresses", RFC 2526, March 1999.
[RFC2629] Rose, M., "Writing I-Ds and RFCs using XML", RFC 2629,
June 1999.
[RFC3306] Haberman, B. and D. Thaler, "Unicast-Prefix-based IPv6
Multicast Addresses", RFC 3306, August 2002.
[RFC3307] Haberman, B., "Allocation Guidelines for IPv6 Multicast
Addresses", RFC 3307, August 2002.
[RFC3972] Aura, T., "Cryptographically Generated Addresses (CGA)",
RFC 3972, March 2005.
[RFC4941] Narten, T., Draves, R., and S. Krishnan, "Privacy
Extensions for Stateless Address Autoconfiguration in
IPv6", RFC 4941, September 2007.
[RFC4982] Bagnulo, M. and J. Arkko, "Support for Multiple Hash
Algorithms in Cryptographically Generated Addresses
(CGAs)", RFC 4982, July 2007.
[RFC5214] Templin, F., Gleeson, T., and D. Thaler, "Intra-Site
Automatic Tunnel Addressing Protocol (ISATAP)", RFC 5214,
March 2008.
[RFC5535] Bagnulo, M., "Hash-Based Addresses (HBA)", RFC 5535, June
2009.
[RFC6052] Bao, C., Huitema, C., Bagnulo, M., Boucadair, M., and X.
Li, "IPv6 Addressing of IPv4/IPv6 Translators", RFC 6052,
October 2010.
[RFC6164] Kohno, M., Nitzan, B., Bush, R., Matsuzaki, Y., Colitti,
L., and T. Narten, "Using 127-Bit IPv6 Prefixes on Inter-
Router Links", RFC 6164, April 2011.
[RFC6741] Atkinson,, RJ., "Identifier-Locator Network Protocol
(ILNP) Engineering Considerations", RFC 6741, November
2012.
[RFC6775] Shelby, Z., Chakrabarti, S., Nordmark, E., and C. Bormann,
"Neighbor Discovery Optimization for IPv6 over Low-Power
Carpenter & Jiang Expires June 5, 2014 [Page 10]
Internet-Draft IPv6 IID significance December 2013
Wireless Personal Area Networks (6LoWPANs)", RFC 6775,
November 2012.
[RFC6957] Costa, F., Combes, J-M., Pougnard, X., and H. Li,
"Duplicate Address Detection Proxy", RFC 6957, June 2013.
Authors' Addresses
Brian Carpenter
Department of Computer Science
University of Auckland
PB 92019
Auckland 1142
New Zealand
Email: brian.e.carpenter@gmail.com
Sheng Jiang
Huawei Technologies Co., Ltd
Q14, Huawei Campus
No.156 Beiqing Road
Hai-Dian District, Beijing 100095
P.R. China
Email: jiangsheng@huawei.com
Carpenter & Jiang Expires June 5, 2014 [Page 11]
