Internet DRAFT - draft-ietf-bess-v4-v6-pe-all-safi
draft-ietf-bess-v4-v6-pe-all-safi
BESS Working Group G. Mishra
Internet-Draft Verizon Inc.
Intended status: Standards Track M. Mishra
Expires: 8 May 2024 Cisco Systems
J. Tantsura
Microsoft, Inc.
S. Madhavi
Juniper Networks, Inc.
Q. Yang
Arista Networks
A. Simpson
Nokia
S. Chen
Huawei Technologies
5 November 2023
IPv4-Only and IPv6-Only PE Design DESIGN ALL SAFI
draft-ietf-bess-v4-v6-pe-all-safi-00
Abstract
As Enterprises and Service Providers upgrade their brown field or
green field MPLS/SR core to an IPv6 transport, Multiprotocol BGP (MP-
BGP)now plays an important role in the transition of their Provider
(P) core network as well as Provider Edge (PE) Inter-AS peering
network from IPv4 to IPv6. Operators must have flexiblity to
continue to support IPv4 customers when both the Core and Edge
networks migrate to IPv6. As well as must be able to support IPv6
networks in cases where operators decide to remain on an IPv4 network
or during transition.
This document details the External BGP (eBGP) PE-PE Inter-AS and PE-
CE Edge peering IPv4-Only PE design where both IPv4 and IPv6 all
supported SAFI NLRI can be advertised over a single IPv4 peer and
IPv6-Only PE Design where all supported SAFI NLRI can be advertised
over a single IPv6 peer.
This document also defines a new IPv4 BGP next hop encoding standard
that uses an IPv4 address as the next hop and not an IPv4 mapped IPv6
address.
Mishra, et al. Expires 8 May 2024 [Page 1]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
This document also provides vendor specific test cases for the
IPv4-Only peering design and IPv6-Only PE design as well as test
results for the five major vendors stakeholders in the routing and
switching indusrty, Cisco, Juniper, Arista, Nokia and Huawei. With
the test results provided for the IPv6-Only Edge peering design, the
goal is that all other vendors around the world that have not been
tested will begin to adopt and implement the design.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 8 May 2024.
Copyright Notice
Copyright (c) 2023 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Requirements Language . . . . . . . . . . . . . . . . . . . . 8
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 8
4. Problem Statement . . . . . . . . . . . . . . . . . . . . . . 9
5. IPv6-Only PE-CE Design ALL SAFI Solution . . . . . . . . . . 10
6. IPv4-Only PE-CE Design ALL SAFI Solution . . . . . . . . . . 12
7. IPv6-Only Edge Peering Design ALL SAFI . . . . . . . . . . . 15
Mishra, et al. Expires 8 May 2024 [Page 2]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
7.1. IPv6-Only Edge Peering Packet Walk ALL SAFI . . . . . . . 15
7.2. IPv6-Only PE Design ALL SAFI over IPv4-Only Core Packet
Walk . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.3. IPv6-Only PE Design ALL SAFI over IPv6-Only Core Packet
Walk . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8. IPv4-Only Edge Peering Design . . . . . . . . . . . . . . . . 20
8.1. IPv4-Only Edge Peering Packet Walk ALL SAFI . . . . . . . 20
8.2. IPv4-Only PE Design ALL SAFI over IPv4-Only Core Packet
Walk . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8.3. IPv4-Only PE Design ALL SAFI over IPv6-Only Core Packet
Walk . . . . . . . . . . . . . . . . . . . . . . . . . . 22
9. IPv6-Only PE Design ALL SAFI RFC8950 Applicability . . . . . 25
9.1. IPv6-Only Edge Peering design next-hop encoding . . . . . 25
9.2. RFC8950 updates to RFC5549 applicability . . . . . . . . 25
10. IPv4 Next Hop Encoding . . . . . . . . . . . . . . . . . . . 26
11. IPv6-Only PE Design for ALL AFI/SAFI . . . . . . . . . . . . 27
11.1. IPv6-Only PE Design All SAFI Case-1 E2E IPv6-Only PE-CE,
Global Table over IPv4-Only Core(6PE) . . . . . . . . . 29
11.2. IPv6-Only PE Design All SAFI Case-2 E2E IPv6-Only PE-CE,
VPN over IPv4-Only Core . . . . . . . . . . . . . . . . 30
11.3. IPv6-Only PE Design All SAFI Case-3 E2E IPv6-Only PE-CE,
Global Table over IPv6-Only Core (4PE) . . . . . . . . 30
11.4. IPv6-Only PE Design All SAFI Case-4 E2E IPv6-Only PE-CE,
VPN over IPv6-Only Core . . . . . . . . . . . . . . . . 31
11.5. IPv6-Only PE Design All SAFI Case-5 E2E IPv6-Only PE-CE,
Global Table over IPv4-Only Core(6PE) - Inter-AS
Option-B . . . . . . . . . . . . . . . . . . . . . . . 31
11.6. IPv6-Only PE Design All SAFI Case-6 E2E IPv6-Only PE-CE,
Global Table over IPv4-Only Core(6PE) - Inter-AS
Option-C . . . . . . . . . . . . . . . . . . . . . . . 32
11.7. IPv6-Only PE Design All SAFI Case-7 E2E IPv6-Only PE-CE,
VPN over IPv4-Only - Inter-AS Option-B . . . . . . . . 32
11.8. IPv6-Only PE Design All SAFI Case-8 E2E IPv6-Only PE-CE,
VPN over IPv4-Only Core - Inter-AS Option-C . . . . . . 33
11.9. IPv6-Only PE Design All SAFI Case-9 E2E IPv6-Only PE-CE,
Global Table over IPv6-Only Core - Inter-AS Option-B . 33
11.10. IPv6-Only PE Design All SAFI Case-10 E2E IPv6-Only PE-CE,
Global Table over IPv6-Only Core - Inter-AS Option-C . 34
11.11. IPv6-Only PE Design All SAFI Case-4 E2E IPv6-Only PE-CE,
VPN over IPv6-Only Core - Inter-AS Option-B . . . . . . 34
11.12. IPv6-Only PE Design All SAFI Case-12 E2E IPv6-Only PE-CE,
VPN over IPv6-Only Core - Inter-AS Option-C . . . . . . 35
11.13. IPv6-Only PE-CE Operational Considerations Testing . . . 35
12. IPv4-Only PE Design for ALL AFI/SAFI . . . . . . . . . . . . 36
12.1. IPv4-Only PE Design All SAFI Case-1 E2E IPv4-Only PE-CE,
Global Table over IPv4-Only Core(6PE) . . . . . . . . . 37
12.2. IPv4-Only PE Design All SAFI Case-2 E2E IPv4-Only PE-CE,
VPN over IPv4-Only Core . . . . . . . . . . . . . . . . 38
Mishra, et al. Expires 8 May 2024 [Page 3]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
12.3. IPv4-Only PE Design All SAFI Case-3 E2E IPv4-Only PE-CE,
Global Table over IPv6-Only Core (4PE) . . . . . . . . 38
12.4. IPv4-Only PE Design All SAFI Case-4 E2E IPv4-Only PE-CE,
VPN over IPv6-Only Core . . . . . . . . . . . . . . . . 39
12.5. IPv4-Only PE Design All SAFI Case-5 E2E IPv4-Only PE-CE,
Global Table over IPv4-Only Core(6PE) - Inter-AS
Option-B . . . . . . . . . . . . . . . . . . . . . . . 39
12.6. IPv4-Only PE Design All SAFI Case-6 E2E IPv4-Only PE-CE,
Global Table over IPv4-Only Core(6PE) - Inter-AS
Option-C . . . . . . . . . . . . . . . . . . . . . . . 40
12.7. IPv4-Only PE Design All SAFI Case-7 E2E IPv4-Only PE-CE,
VPN over IPv4-Only - Inter-AS Option-B . . . . . . . . 40
12.8. IPv4-Only PE Design All SAFI Case-8 E2E IPv4-Only PE-CE,
VPN over IPv4-Only Core - Inter-AS Option-C . . . . . . 41
12.9. IPv4-Only PE Design All SAFI Case-9 E2E IPv4-Only PE-CE,
Global Table over IPv6-Only Core - Inter-AS Option-B . 41
12.10. IPv4-Only PE Design All SAFI Case-10 E2E IPv4-Only PE-CE,
Global Table over IPv6-Only Core - Inter-AS Option-C . 42
12.11. IPv4-Only PE Design All SAFI Case-11 E2E IPv4-Only PE-CE,
VPN over IPv6-Only Core - Inter-AS Option-B . . . . . . 42
12.12. IPv4-Only PE Design All SAFI Case-12 E2E IPv4-Only PE-CE,
VPN over IPv6-Only Core - Inter-AS Option-C . . . . . . 43
12.13. IPv4-Only PE-CE Operational Considerations Testing . . . 43
13. IPv4-Only PE Design and IPv6-Only PE Design ALL AFI/SFI
Operational Considerations . . . . . . . . . . . . . . . 44
14. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 45
15. Security Considerations . . . . . . . . . . . . . . . . . . . 45
16. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 45
17. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 45
18. References . . . . . . . . . . . . . . . . . . . . . . . . . 45
18.1. Normative References . . . . . . . . . . . . . . . . . . 45
18.2. Informative References . . . . . . . . . . . . . . . . . 49
Appendix A. SAFI LIST FOR PE-CE Edge Scenario . . . . . . . . . 51
Appendix B. SAFI LIST FOR Inter-AS PE-PE Scenario . . . . . . . 51
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 53
1. Introduction
As Enterprises and Service Providers upgrade their brown field or
green field MPLS/SR core to an IPv6 transport such as MPLS LDPv6, SR-
MPLSv6 or SRv6, Multiprotocol BGP (MP-BGP) now plays an important
role in the transition of the Provider (P) core networks and Provider
Edge (PE) edge networks from IPv4 to IPv6.
IXP are also facing IPv4 address depletion at their peering points,
which are large Layer 2 transit backbones that service providers peer
and exchange IPv4 and IPv6 Network Layer Reachability Information
(NLRI). Today, these transit exchange points are Dual Stacked. With
Mishra, et al. Expires 8 May 2024 [Page 4]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
this IPv6-only BGP peering design, only IPv6 MUST be configured on
the PE-PE inter-as peering interface, the Inter-AS Provider Edge (PE)
- Provider Edge (PE), the IPv6 BGP peer is now used to carry IPv4
(Network Layer Reachability Information) NLRI over an IPv6 next hop
using IPv6 next hop encoding defined in [RFC8950], while continuing
to forward both IPv4 and IPv6 packets. With this IPv6-Only PE
Design, ASBRs providing Inter-AS options peering PE to PE extending
L3 VPN services is now no longer Dual Stacked and as well can support
ALL AFI/SAFI.
This document also provides a solution for use cases where operators
are not yet ready to migrate to IPv6 or SRv6 core and would like to
stay on IPv4-Only Core short to long term and maybe even
indefinitely. With this design, operators can now remain with an
IPv4-Only Core and do not have to migrate to an IPv6-Only Core. From
a technical standpoint the underlay can remain IPv4 and still
transport IPv6 NLRI to support IPv6 customers, and so does not need
to be migrated to IPv6-Only underlay. With this IPv4-Only PE Design
solution , IPv4 addressing only needs to be provisioned for the
IPv4-Only PE-CE eBGP Edge peering design, thereby eliminating IPv6
provisioning at the Edge. This core and edge IPv4-Only peering
design can apply to any eBGP peering, public internet or private,
which can be either Core networks, Data Center networks, Access
networks or can be any eBGP peering scenario.
MP-BGP specifies that the set of usable next-hop address families is
determined by the Address Family Identifier (AFI) and the Subsequent
Address Family Identifier (SAFI). Historically the AFI/SAFI
definitions for the IPv4 address family only have provisions for
advertising a Next Hop address that belongs to the IPv4 protocol when
advertising IPv4 or VPN-IPv4. [RFC8950] specifies the extensions
necessary to allow advertising IPv4 NLRI, Virtual Private Network
Unicast (VPN-IPv4) NLRI, Multicast Virtual Private Network (MVPN-
IPv4) NLRI with a Next Hop address that belongs to the IPv6 protocol.
This comprises of an extended next hop encoding MP-REACH BGP
capability exchange to allow the address of the Next Hop for IPv4
NLRI, VPN-IPv4 NLRI and MVPN-IPv4 NLRI to also belong to the IPv6
Protocol. [RFC8950] defines the encoding of the Next Hop to
determine which of the protocols the address actually belongs to, and
a new BGP Capability allowing MP-BGP Peers to discover dynamically
whether they can exchange IPv4 NLRI and VPN-IPv4 NLRI with an IPv6
Next Hop.
With the new extensions defined in [RFC8950] supporting NLRI and next
hop address family mismatch, the BGP peer session can now be treated
as a pure TCP transport and carry both IPv4 and IPv6 NLRI at the
Provider Edge (PE) - Customer Edge (CE) over a single IPv6 TCP
session. This allows for the elimination of dual stack from the PE-
Mishra, et al. Expires 8 May 2024 [Page 5]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
PE Inter-AS peering point, and now enable the Inter-AS peering to be
IPv6-ONLY. The elimination of IPv4 Inter Provider ASBR tie point,
PE-PE Inter-AS peering points translates into OPEX expenditure
savings of point-to-point infrastructure links as well as /31 address
space savings and administration and network management of both IPv4
and IPv6 BGP peers. This reduction decreases the number of PE-PE
Inter-AS options BGP peers by fifty percent, which is a tremendous
cost savings for operators.
This document details an important External BGP (eBGP) PE-CE Edge and
PE-PE Inter-AS IPv4-Only PE Design and IPv6-Only PE Peering Design
that leverages the MP-BGP capability exchange by using single IPv4
peering or IPv6 peering as pure transport, allowing all IPv4 Network
Layer Reachability Information (NLRI) and IPv6 Network Layer
Reachability Information (NLRI)to be carried over the same (Border
Gateway Protocol) BGP TCP session for all supported Subsequent
Address Family Identifiers(SAFI).
The design change provides two new alternative to traditional Dual
Stacking implemnted today while providing the same Dual Stacking
functionality and capabilities that exists today with separate IPv4
and IPv6 BGP sessions, but now with this paradigm shift now only
requires a single IPv4 transport peer "IPv4-Only PE Design" or single
IPv6 transport peer "IPv6-Only PE Design".
IPv6-Only PE Design entails that an IPv4 address MUST not be
configured on the PE-CE or PE-PE interface and with the IPv6-Only PE
Design an IPv4 address must not be configured on the PE-CE or PE-PE
interface.
IPv4-Only PE Design entails that an IPv6 address MUST not be
configured on the PE-CE or PE-PE interface and with the IPv4-Only PE
Design an IPv6 address must not be configured on the PE-CE or PE-PE
interface.
From a control plane perspective with the IPv6-Only PE design a
single IPv6-Only peer is required for both IPv4 and IPv6 routing
updates and from a data plane forwarindg perspective an IPv6 address
need only be configured on the PE-CE Edge or PE-PE Inter-AS peering
interface for both IPv4 and IPv6 packet forwarding.
From a control plane perspective with the IPv4-Only PE design a
single IPv4-Only peer is required for both IPv4 and IPv6 routing
updates and from a data plane forwarindg perspective an IPv4 address
need only be configured on the PE-CE Edge or PE-PE Inter-AS peering
interface for both IPv4 and IPv6 packet forwarding.
Mishra, et al. Expires 8 May 2024 [Page 6]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
This document defines the IPv6-Only PE Design and IPv4-Only PE Design
as a new PE-CE Edge and ASBR-ASBR PE-PE Inter-AS BGP peering Standard
to support all IPv4 and IPv6 AFI AFI and corresponding SAFI
ubiquitously. As service providers migrate to Segment Routing
architecture SR-MPLS and SRv6, VPN overlay exsits as well, and thus
Inter-AS options Option-A, Option-B, Option-AB and Option-C are still
applicable and thus this pardigm shift to IPv4-Only or IPv6-Only
peering architecure is still very relevant to Segment Routing
architecture both SR-MPLS and SRv6.
With both the IPv4-Only PE Design and IPv6-Only PE Design, while the
savings exists at the Edge eBGP PE-PE Inter-AS peering, on the core
side iBGP PE to Route Reflector (RR) peering carrying <AFI/SAFI> IPv4
<1/1>, VPN-IPV4 <1/128>, and Multicasat VPN <1/129>, there is no
savings as the Provider (P) Core is IPv6 Only or IPv4-Only, thus can
only have an IPv6 peer and must use [RFC8950] extended next hop
encoding to carrying IPv4 NLRI IPV4 <2/1>, VPN-IPV4 <2/128>, and
Multicast VPN <2/129> over an IPv4 or IPv6 next hop.
The IPv4-Only PE Design and IPv6-Only PE ALL SAFI Design supports the
following IPv4 and IPv6 AFI and their corresponding SAFI below: <AFI/
SAFI> MCAST-VPN [RFC6514] <1/5>, NLRI Multi-Segment Pseudowires
[RFC7267] <1/6>, BGP Tunnel Encapsulation SAFI [RFC9012] <1/7>,
MCAST-VPLS [RFC7117] <1/8>, Tunnel SAFI
[I-D.nalawade-kapoor-tunnel-safi] <1/6>, BGP MDT SAFI [RFC6037]
<1/66>, BGP 4to6 SAFI [RFC5747] <1/67>, BGP 6to4 SAFI draft xx <1/8>,
Layer 1 VPN Auto-Discovery [RFC5195] <1/69>, SR-TE Policy SAFI draft
<1/73>, BGP 6to4 SAFI draft <1/8>, SDN WAN Capabilities draft <1/74>,
Classful-Transport SAFI draftxx <1/76>, Tunneled Traffic FlowSpec
draftxx <1/77>, MCAST-TREE SAFI draft xx <1/78>, Route Target
Constraints [RFC4684] <1/132>, Dissemination of Flow Specification
Rules [RFC8955] <1/133>, L3 VPN Dissemination of Flow Specification
Rules [RFC8955] <1/1344>, VPN Auto-Discovery SAFI draftxx <1/140>
This document provides proof of concept test results for the
IPv4-Only PE Design and IPv6-Only PE design for 12 of the most common
use cases with 3 of the most commonly used SAFI <AFI/SAFI> IPv4
<1/1>, VPN-IPV4 <1/128>, and Multicasat VPN <1/129>, with five major
vendors stakeholders in the routing and switching indusrty, Cisco,
Juniper, Arista, Nokia and Huawei. With the test results provided
for the IPv6-Only Edge peering design, the goal is that all other
vendors around the world that have not been tested will begin to
adopt and implement this new best practice for eBGP IPv6-Only Edge
peering. This will give confidence to operators to start the
proliferation of the IPv4-Only PE Design and IPv6-Only PE design
worldwide. This document provides a detalied analysis of all IPv4
and IPv6 address family and related SAFI that is supported with the
IPv4-Only PE Design and IPv6-Only PE Design in Section 4. Thus this
Mishra, et al. Expires 8 May 2024 [Page 7]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
draft provides a test use case basis with the three SAFI tested,
giving extensibility to all of the other SAFI that are supported for
future testing and deployment by operators.
This document also defines a new IPv4 next hop encoding for IPv6 NLRI
over IPv4 Next Hop to uses 4 byte IPv4 address for the next hop and
not a IPv4 mapped IPv6 address as the new standard. Today the IPv4
next hop encoding has mix of 4 octet IPv4 address for the next hop as
well as IPv4 mapped IPv6 address. This is discussed in detail in
section 10.
The Major benefit from the IPv4-Only PE design is IPv6 address space
savings and the ability to support IPv6 NLRI without configuring an
IPv6 address at the PE-CE edge and PE-PE inter-as boundary and avoid
having to upgrade to support IPv6 as well elimination of provisioning
of IPv6 addressing and Network Operations and monitoring costs of
tradditional Dual Stacked interfaces with IPv4 and IPv6 BGP peering
which now translating into CAPEX and OPEX Savings.
The Major benefit from the IPv6-Only PE design is IPv4 address space
savings solving IPv4 address depletion issues and the ability to
support IPv4 NLRI without configuring an IPv4 address at the PE-CE
edge and PE-PE inter-as boundary, as well elimination of provisioning
of IPv4 address and Network Operations and monitoring costs of
traditional Dual Stacked interfaces with IPv4 and IPv6 BGP peering
which now translates into CAPEX and OPEX Savings.
2. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
3. Terminology
Terminolgoy used in defining the IPv6-Only Edge specification.
AFBR: Address Family Border Router Provider Edge (PE).
Edge: PE-CE Edge Network Provider Edge - Customer Edge
Core: P Core Network Provider (P)
4to6 Softwire : IPv4 edge over an IPv6-Only core
6to4 Softwire: IPv6 edge over an IPv4-Only core
Mishra, et al. Expires 8 May 2024 [Page 8]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
E2E: End to End
4. Problem Statement
This specification addresses a real issue that has been discussed at
many operator with extremely large core networks around the world
related migration to IPv6 underlay transport which can now be put off
indefinitely. Operators around the world are clamoring for a
solution as well that can help solve issues related to IPv4 address
depletion at these large IXP peering points.
Problem Statement
Dual Stacked Dual Stacked
CE PE
+-------+ IPv4 BGP Peer +-------+
| |---------------| |
| CE | IPv6 BGP Peer | PE |
| |---------------| |
+-------+ +-------+
IPv4 forwarding IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 1: Problem Statement - Dual Stack Peering
________
Dual Stacked _____ / \ Dual Stacked
PE / CE / \__/ \___ PE / CE
+----+ +----+ / \ +------+ +-----+
| | | | |0====VPN Overlay Tunnel ==0| | | | |
| | | | | \ | | | |
| CE |--| PE |--\ IPv6-Only Core |----| PE |---| CE |
| | | | \0=========Underlay =======0| | | | |
+----+ +----+ \ __/ +------+ +-----+
IPv4 IPv6 BGP peer \ IP / MPLS / SR domain / IPv4 and IPv6 BGP peer
IPv4 forwarding \__ __ / IPv4 forwarding
IPv6 forwarding \_______/ \_____/ IPv6 forwarding
Figure 2: Problem Statement - E2E Dual Stack Edge
Mishra, et al. Expires 8 May 2024 [Page 9]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
5. IPv6-Only PE-CE Design ALL SAFI Solution
The IPv6-Only Edge design solution applies to ALL IPv4 Network Layer
Reachability Information (NLRI) and IPv6 Network Layer Reachability
Information (NLRI) over an IPv6-Only BGP Peering session.
IPv6-Only PE Design is applicable to infrastructure networks such as
Core networks, DC networks, Access networks as well as any PE-CE
public or private network can now utilize this IPv6-Only Edge
solution and reap the benefits immediately on IPv6 address space
saving and CAPEX and OPEX savings.
Six Groupings of AFI/SAFI Use Case Scenario for the IPv6-Only PE
Design ALL SAFI
* Group-1 PE-CE
* Group-2 PE-PE Inter-AS
* Group-3 L1 and L2 VPN
* Group-4 Multicast
* Group-5 Tunnel
* Group-6 BGP, BGP Flowspec, BGP Misc Policy
Group-1 Edge Customer IPv4/IPv6 NLRI PE-CE AFI / SAFI grouping (CP-
DP) - "UNICAST"
* AFI/SAFI 1/1 IPv4 Unicast 2/1 IPv6 Unicast
Group-1 Edge Customer IPv4/IPv6 NLRI PE-CE AFI / SAFI grouping (CP-
DP) - "MULTICAST"
* AFI/SAFI 1/2 IPv4 Multicast 2/2 IPv6 Multicast
* AFI/SAFI 1/78 IPv4 MCAST-TREE SAFI 2/78 MCAST-TREE SAFI
Group-2 ASBR-ASBR Inter-AS Customer IPv4/IPv6 NLRI AFI/SAFI grouping
(CP-DP) - "UNICAST"
Global Table
* AFI/SAFI 1/4 4PE
L3 VPN
Mishra, et al. Expires 8 May 2024 [Page 10]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
* AFI/SAFI 1/128 IPv4 VPN 2/128 IPv6 VPN
* AFI/SAFI 1/132 IPv4 RTC 2/132 IPv6 RTC
* AFI/SAFI 1/140 IPv4 VPN Auto Discovery 2/140 IPv6 VPN Auto
Discovery
Group-2 ASBR-ASBR Inter-AS Customer IPv4/IPv6 NLRI AFI/SAFI grouping
(CP-DP) - "MULTICAST"
Global Table
* AFI/SAFI 1/2 IPv4 Multicast 2/2 IPv6 Multicast
L3 VPN
* AFI/SAFI 1/129 IPv4 MVPN 2/129 IPv6 MVPN
* AFI/SAFI 1/5 IPv4 MCAST-VPN 2/5 IPv6 MCAST-VPN
* AFI/SAFI 1/66 IPv4 BGP MDT SAFI 2/66 IPv6 BGP MDT SAFI
* AFI/SAFI 1/78 IPv4 MCAST-TREE SAFI 2/78 MCAST-TREE SAFI
Group-3 - L1 and L2 VPN
* L2 VPN related NLRI control plane in BGP
* AFI/SAFI 1/6 IPv4 Multi Segment PW 2/6 IPv6 Multi Segment PW
* AFI/SAFI 1/69 L1 VPN Auto Discovery 2/69 L1 VPN Auto Discovery
Group-4 - Multicast
* AFI/SAFI 1/8 IPv4 MCAST-VPLS 2/8 IPv6 MCAST-VPLS
Group-5 - Tunnel
* AFI/SAFI 1/64 Tunnel-SAFI 2/64 Tunnel-SAFI
* AFI/SAFI 1/67 BGP 4over6 Tunnel SAFI 2/67 BGP 4over6 Tunnel SAFI
* AFI/SAFI 1/68 BGP 6over4 Tunnel SAFI 2/68 BGP 6over4 Tunnel SAFI
Group-6 - BGP, BGP Flowspec, BGP Misc Policy
* AFI/SAFI 1/73 SR-TE Policy SAFI 2/73 SR-TE Policy SAFI
Mishra, et al. Expires 8 May 2024 [Page 11]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
* AFI/SAFI 1/74 SD-WAN Capabilities 2/74 SD-WAN Capabilities
* AFI/SAFI 1/77 Tunneled Traffic Flowspec 2/77 Tunneled Traffic
Flowspec
* AFI/SAFI 1/133 Dissemination of Flowspec Rules 2/133 133
Dissemination of Flowspec Rules
* AFI/SAFI 1/134 L3 VPN 133 Dissemination of Flowspec Rules 2/134
L3VPN Dissemination of Flowspec Rules
* AFI/SAFI 1/79 BGP-DPS Arista 2/79 BGP-DPS Arista
* AFI/SAFI 1/83 BGP CAR 2/83 BGP CAR
* AFI/SAFI 1/84 BGP VPN CAR 2/84 BGP VPN CAR
* AFI/SAFI 1/85 BGP MUP SAFI 2/85 BGP MUP SAFI
Solution applicable to all AFI/SAFI
AFI/SAFI 1/X 2/X Where X = ALL SAFI
+-------+ +-------+
| AS1 | IPv6 Only | AS2 |
| PE1 |----------------| PE2 |
| (ASBR)| IPv6 BGP Peer |(ASBR) |
+-------+ +-------+
IPv4 forwarding IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 3: IPv6-Only PE Design Solution Applicability to ALL AFI/SAFI
6. IPv4-Only PE-CE Design ALL SAFI Solution
The IPv4-Only Edge design solution applies to ALL IPv4 Network Layer
Reachability Information (NLRI) and IPv6 Network Layer Reachability
Information (NLRI) over an IPv4-Only BGP Peering session.
IPv4-Only PE Design is applicable to infrastructure networks such as
Core networks, DC networks, Access networks as well as any PE-CE
public or private network can now utilize this IPv4-Only Edge
solution and reap the benefits immeditately of CAPEX and OPEX
savings.
Six Groupings of AFI/SAFI Use Case Scenario for the IPv6-Only PE
Design ALL SAFI
Mishra, et al. Expires 8 May 2024 [Page 12]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
* Group-1 PE-CE
* Group-2 PE-PE Inter-AS
* Group-3 L1 and L2 VPN
* Group-4 Multicast
* Group-5 Tunnel
* Group-6 BGP, BGP Flowspec, BGP Misc Policy
Group-1 Edge Customer IPv4/IPv6 NLRI PE-CE AFI / SAFI grouping (CP-
DP) - "UNICAST"
* AFI/SAFI 1/1 IPv4 Unicast 2/1 IPv6 Unicast
Group-1 Edge Customer IPv4/IPv6 NLRI PE-CE AFI / SAFI grouping (CP-
DP) - "MULTICAST"
* AFI/SAFI 1/2 IPv4 Multicast 2/2 IPv6 Multicast
* AFI/SAFI 1/78 IPv4 MCAST-TREE SAFI 2/78 MCAST-TREE SAFI
Group-2 ASBR-ASBR Inter-AS Customer IPv4/IPv6 NLRI AFI/SAFI grouping
(CP-DP) - "UNICAST"
Global Table
* AFI/SAFI 1/4 4PE
L3 VPN
* AFI/SAFI 1/128 IPv4 VPN 2/128 IPv6 VPN
* AFI/SAFI 1/132 IPv4 RTC 2/132 IPv6 RTC
* AFI/SAFI 1/140 IPv4 VPN Auto Discovery 2/140 IPv6 VPN Auto
Discovery
Group-2 ASBR-ASBR Inter-AS Customer IPv4/IPv6 NLRI AFI/SAFI grouping
(CP-DP) - "MULTICAST"
Global Table
* AFI/SAFI 1/2 IPv4 Multicast 2/2 IPv6 Multicast
L3 VPN
Mishra, et al. Expires 8 May 2024 [Page 13]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
* AFI/SAFI 1/129 IPv4 MVPN 2/129 IPv6 MVPN
* AFI/SAFI 1/5 IPv4 MCAST-VPN 2/5 IPv6 MCAST-VPN
* AFI/SAFI 1/66 IPv4 BGP MDT SAFI 2/66 IPv6 BGP MDT SAFI
* AFI/SAFI 1/78 IPv4 MCAST-TREE SAFI 2/78 MCAST-TREE SAFI
Group-3 - L1 and L2 VPN
* L2 VPN related NLRI control plane in BGP
* AFI/SAFI 1/6 IPv4 Multi Segment PW 2/6 IPv6 Multi Segment PW
* AFI/SAFI 1/69 L1 VPN Auto Discovery 2/69 L1 VPN Auto Discovery
Group-4 - Multicast
* AFI/SAFI 1/8 IPv4 MCAST-VPLS 2/8 IPv6 MCAST-VPLS
Group-5 - Tunnel
* AFI/SAFI 1/64 Tunnel-SAFI 2/64 Tunnel-SAFI
* AFI/SAFI 1/67 BGP 4over6 Tunnel SAFI 2/67 BGP 4over6 Tunnel SAFI
* AFI/SAFI 1/68 BGP 6over4 Tunnel SAFI 2/68 BGP 6over4 Tunnel SAFI
Group-6 - BGP, BGP Flowspec, BGP Misc Policy
* AFI/SAFI 1/73 SR-TE Policy SAFI 2/73 SR-TE Policy SAFI
* AFI/SAFI 1/74 SD-WAN Capabilities 2/74 SD-WAN Capabilities
* AFI/SAFI 1/77 Tunneled Traffic Flowspec 2/77 Tunneled Traffic
Flowspec
* AFI/SAFI 1/133 Dissemination of Flowspec Rules 2/133 133
Dissemination of Flowspec Rules
* AFI/SAFI 1/134 L3 VPN 133 Dissemination of Flowspec Rules 2/134
L3VPN Dissemination of Flowspec Rules
* AFI/SAFI 1/79 BGP-DPS Arista 2/79 BGP-DPS Arista
* AFI/SAFI 1/83 BGP CAR 2/83 BGP CAR
* AFI/SAFI 1/84 BGP VPN CAR 2/84 BGP VPN CAR
Mishra, et al. Expires 8 May 2024 [Page 14]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
* AFI/SAFI 1/85 BGP MUP SAFI 2/85 BGP MUP SAFI
Solution applicable to all AFI/SAFI
AFI/SAFI 1/X 2/X Where X = ALL SAFI
+-------+ +-------+
| AS1 | IPv6 Only | AS2 |
| PE1 |----------------| PE2 |
| (ASBR)| IPv6 BGP Peer |(ASBR) |
+-------+ +-------+
IPv4 forwarding IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 4: IPv4-Only PE Design Solution Applicability to ALL AFI/SAFI
________
IPv4-Only _____ / \ IPv4-Only
PE / CE / \__/ \___ PE / CE
+----+ +----+ / \ +------+ +-----+
| | | | |0====VPN Overlay Tunnel ==0| | | | |
| | | | | \ | | | |
| CE |--| PE |--\ IPv4-Only Core |----| PE |---| CE |
| | | | \0=========Underlay ===== ==0 | | | |
+----+ +----+ \ __/ +------+ +-----+
IPv6 BGP peer \IP / MPLS / SR domain / IPv6 BGP peer
IPv4 forwarding \__ __ / IPv4 forwarding
IPv6 forwarding \_______/ \_____/ IPv6 forwarding
Figure 5: E2E VPN Solutionv4
7. IPv6-Only Edge Peering Design ALL SAFI
7.1. IPv6-Only Edge Peering Packet Walk ALL SAFI
The IPv6-Only Edge Peering design utilizes two key E2E Softwire Mesh
Framework scenario's, 4to6 softwire and 6to4 softwire. The Softwire
mesh framework concept is based on the overlay and underlay MPLS or
SR based technology framework, where the underlay is the transport
layer and the overlay is a Virtual Private Network (VPN) layer, and
is the the tunneled virtualization layer containing the customer
payload. The concept of a 6to4 Softwire is based on transmission of
IPv6 packets at the edge of the network by tunneling the IPv6 packets
Mishra, et al. Expires 8 May 2024 [Page 15]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
over an IPv4-Only Core. The concept of a 4to6 Softwire is also based
on transmission of IPv4 packets at the edge of the network by
tunneling the IPv4 packets over an IPv6-Only Core.
This document describes End to End (E2E) test scenarios that follow a
packet flow from IPv6-Only attachment circuit from ingress PE-CE to
egress PE-CE tracing the routing protocol control plane and data
plane forwarding of IPv4 packets in a 4to6 softwire or 6to4 softwire
within the IPv4-Only or IPv6-Only Core network. In both secneario we
are focusing on IPv4 packets and the control plane and data plane
forwarding aspects of IPv4 packets from the PE-CE Edge network over
an IPv6-Only P (Provider) core network or IPv4-Only P (Provider) core
network. With this IPv6-Only Edge peering design, the Softwire Mesh
Framework is not extended beyond the Provider Edge (PE) and continues
to terminate on the PE router.
7.2. IPv6-Only PE Design ALL SAFI over IPv4-Only Core Packet Walk
6to4 softwire where IPv6-Edge eBGP IPv6 peering where IPv4 packets at
network Edge traverse a IPv4-Only Core
In the scenario where IPv4 packets originating from a PE-CE edge are
tunneled over an MPLS or Segment Routing IPv4 underlay core network,
the PE and CE only have an IPv6 address configured on the interface.
In this scenario the IPv4 packets that ingress the CE from within the
CE AS are over an IPv6-Only interface and are forwarded to an IPv4
NLRI destination prefix learned from the Pure Transport Single IPv6
BGP Peer. In the IPv6-Only Edge peering architecture the PE is
IPv6-Only as all PE-CE interfaces are IPv6-Only. However, on the CE,
the PE-CE interface is the only interface that is IPv6-Only and all
other interfaces may or may not be IPv6-Only. Following the data
plane packet flow, IPv4 packets are forwarded from the ingress CE to
the IPv6-Only ingress PE where the VPN label imposition push per
prefix, per-vrf, per-CE occurs and the labeled packet is forwarded
over a 6to4 softwire IPv4-Only core, to the egress PE where the VPN
label disposition pop occurs and the native IPv4 packet is forwarded
to the egress CE. In the reverse direction IPv4 packets are
forwarded from the egress CE to egress PE where the VPN label
imposition per prefix, per-vrf, per-CE push occurs and the labeled
packet is forwarded back over the 6to4 softwire IPv4-Only core, to
the ingress PE where the VPN label disposition pop occurs and the
native IPv4 packet is forwarded to the ingress CE. . The
functionality of the IPv4 forwarding plane in this scenario is
identical from a data plane forwarding perspective to Dual Stack IPv4
forwarding scenario.
Mishra, et al. Expires 8 May 2024 [Page 16]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
+--------+ +--------+
| IPv4 | | IPv4 |
| Client | | Client |
| Network| | Network|
+--------+ +--------+
| \ / |
| \ / |
| \ / |
| X |
| / \ |
| / \ |
| / \ |
+--------+ +--------+
| AFBR | | AFBR |
+--| IPv4/6 |---| IPv4/6 |--+
| +--------+ +--------+ |
+--------+ | | +--------+
| IPv4 | | | | IPv4 |
| Client | | | | Client |
| Network|------| IPv4 |-------| Network|
+--------+ | only | +--------+
| |
| +--------+ +--------+ |
+--| AFBR |---| AFBR |--+
| IPv4/6 | | IPv4/6 |
+--------+ +--------+
| \ / |
| \ / |
| \ / |
| X |
| / \ |
| / \ |
| / \ |
+--------+ +--------+
| IPv6 | | IPv4 |
| Client | | Client |
| Network| | Network|
+--------+ +--------+
Figure 6: IPv6-Only PE Design ALL SAFI 6to4 Softwire - IPv6 Edge
over an IPv4-Only Core
7.3. IPv6-Only PE Design ALL SAFI over IPv6-Only Core Packet Walk
4to6 softwire where IPv6-Edge eBGP IPv6 peering where IPv4 packets at
network Edge traverse a IPv6-Only Core
Mishra, et al. Expires 8 May 2024 [Page 17]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
In the scenario where IPv4 packets originating from a PE-CE edge are
tunneled over an MPLS or Segment Routing IPv4 underlay core network,
the PE and CE only have an IPv6 address configured on the interface.
In this scenario the IPv4 packets that ingress the CE from within the
CE AS are over an IPv6-Only interface and are forwarded to an IPv4
NLRI destination prefix learned from the Pure Transport Single IPv6
BGP Peer. In the IPv6-Only Edge peering architecture the PE is
IPv6-Only as all PE-CE interfaces are IPv6-Only. However, on the CE,
the PE-CE interface is the only interface that is IPv6-Only and all
other interfaces may or may not be IPv6-Only. Following the data
plane packet flow, IPv4 packets are forwarded from the ingress CE to
the IPv6-Only ingress PE where the VPN label imposition push per
prefix, per-vrf, per-CE occurs and the labeled packet is forwarded
over a 4to6 softwire IPv6-Only core, to the egress PE where the VPN
label disposition pop occurs and the native IPv4 packet is forwarded
to the egress CE. In the reverse direction IPv4 packets are
forwarded from the egress CE to egress PE where the VPN label
imposition per prefix, per-vrf, per-CE push occurs and the labeled
packet is forwarded back over the 4to6 softwire IPv6-Only core, to
the ingress PE where the VPN label disposition pop occurs and the
native IPv4 packet is forwarded to the ingress CE. . The
functionality of the IPv4 forwarding plane in this scenario is
identical from a data plane forwarding perspective to Dual Stack IPv4
forwarding scenario.
Mishra, et al. Expires 8 May 2024 [Page 18]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
+--------+ +--------+
| IPv4 | | IPv4 |
| Client | | Client |
| Network| | Network|
+--------+ +--------+
| \ / |
| \ / |
| \ / |
| X |
| / \ |
| / \ |
| / \ |
+--------+ +--------+
| AFBR | | AFBR |
+--| IPv4/6 |---| IPv4/6 |--+
| +--------+ +--------+ |
+--------+ | | +--------+
| IPv6 | | | | IPv6 |
| Client | | | | Client |
| Network|------| IPv6 |-------| Network|
+--------+ | only | +--------+
| |
| +--------+ +--------+ |
+--| AFBR |---| AFBR |--+
| IPv4/6 | | IPv4/6 |
+--------+ +--------+
| \ / |
| \ / |
| \ / |
| X |
| / \ |
| / \ |
| / \ |
+--------+ +--------+
| IPv4 | | IPv4 |
| Client | | Client |
| Network| | Network|
+--------+ +--------+
Figure 7: IPv6-Only PE Design ALL SAFI 4to6 Softwire - IPv4 Edge
over an IPv6-Only Core
Mishra, et al. Expires 8 May 2024 [Page 19]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
8. IPv4-Only Edge Peering Design
8.1. IPv4-Only Edge Peering Packet Walk ALL SAFI
The IPv4-Only Edge Peering design utilizes two key E2E Softwire Mesh
Framework scenario's, 4to6 softwire and 6to4 softwire. The Softwire
mesh framework concept is based on the overlay and underlay MPLS or
SR based technology framework, where the underlay is the transport
layer and the overlay is a Virtual Private Network (VPN) layer, and
is the the tunneled virtualization layer containing the customer
payload. The concept of a 6to4 Softwire is based on transmission of
IPv6 packets at the edge of the network by tunneling the IPv6 packets
over an IPv4-Only Core. The concept of a 4to6 Softwire is also based
on transmission of IPv4 packets at the edge of the network by
tunneling the IPv4 packets over an IPv6-Only Core.
This document describes End to End (E2E) test scenarios that follow a
packet flow from IPv4-Only attachment circuit from ingress PE-CE to
egress PE-CE tracing the routing protocol control plane and data
plane forwarding of IPv4 packets in a 4to6 softwire or 6to4 softwire
within the IPv4-Only or IPv6-Only Core network. In both secneario we
are focusing on IPv4 packets and the control plane and data plane
forwarding aspects of IPv4 packets from the PE-CE Edge network over
an IPv4-Only P (Provider) core network or IPv6-Only P (Provider) core
network. With this IPv4-Only Edge peering design, the Softwire Mesh
Framework is not extended beyond the Provider Edge (PE) and continues
to terminate on the PE router.
8.2. IPv4-Only PE Design ALL SAFI over IPv4-Only Core Packet Walk
6to4 softwire where IPv4-Edge eBGP IPv4 peering where IPv6 packets at
network Edge traverse a IPv4-Only Core
In the scenario where IPv6 packets originating from a PE-CE edge are
tunneled over an MPLS or Segment Routing IPv4 underlay core network,
the PE and CE only have an IPv6 address configured on the interface.
In this scenario the IPv6 packets that ingress the CE from within the
CE AS are over an IPv4-Only interface and are forwarded to an IPv6
NLRI destination prefix learned from the Pure Transport Single IPv4
BGP Peer. In the IPv4-Only Edge peering architecture the PE is
IPv4-Only as all PE-CE interfaces are IPv4-Only. However, on the CE,
the PE-CE interface is the only interface that is IPv4-Only and all
other interfaces may or may not be IPv4-Only. Following the data
plane packet flow, IPv4 packets are forwarded from the ingress CE to
the IPv4-Only ingress PE where the VPN label imposition push per
prefix, per-vrf, per-CE occurs and the labeled packet is forwarded
over a 6to4 softwire IPv4-Only core, to the egress PE where the VPN
label disposition pop occurs and the native IPv4 packet is forwarded
Mishra, et al. Expires 8 May 2024 [Page 20]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
to the egress CE. In the reverse direction IPv4 packets are
forwarded from the egress CE to egress PE where the VPN label
imposition per prefix, per-vrf, per-CE push occurs and the labeled
packet is forwarded back over the 6to4 softwire IPv4-Only core, to
the ingress PE where the VPN label disposition pop occurs and the
native IPv4 packet is forwarded to the ingress CE. . The
functionality of the IPv4 forwarding plane in this scenario is
identical from a data plane forwarding perspective to Dual Stack IPv4
forwarding scenario.
Mishra, et al. Expires 8 May 2024 [Page 21]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
+--------+ +--------+
| IPv4 | | IPv4 |
| Client | | Client |
| Network| | Network|
+--------+ +--------+
| \ / |
| \ / |
| \ / |
| X |
| / \ |
| / \ |
| / \ |
+--------+ +--------+
| AFBR | | AFBR |
+--| IPv4/6 |---| IPv4/6 |--+
| +--------+ +--------+ |
+--------+ | | +--------+
| IPv4 | | | | IPv4 |
| Client | | | | Client |
| Network|------| IPv4 |-------| Network|
+--------+ | only | +--------+
| |
| +--------+ +--------+ |
+--| AFBR |---| AFBR |--+
| IPv4/6 | | IPv4/6 |
+--------+ +--------+
| \ / |
| \ / |
| \ / |
| X |
| / \ |
| / \ |
| / \ |
+--------+ +--------+
| IPv6 | | IPv4 |
| Client | | Client |
| Network| | Network|
+--------+ +--------+
Figure 8: 6to4 Softwire - IPv6 Edge over an IPv4-Only Core Packet
Walk
8.3. IPv4-Only PE Design ALL SAFI over IPv6-Only Core Packet Walk
4to6 softwire where IPv4-Edge eBGP IPv4 peering where IPv6 packets at
network Edge traverse a IPv6-Only Core
Mishra, et al. Expires 8 May 2024 [Page 22]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
In the scenario where IPv6 packets originating from a PE-CE edge are
tunneled over an MPLS or Segment Routing IPv4 underlay core network,
the PE and CE only have an IPv4 address configured on the interface.
In this scenario the IPv6 packets that ingress the CE from within the
CE AS are over an IPv4-Only interface and are forwarded to an IPv6
NLRI destination prefix learned from the Pure Transport Single IPv4
BGP Peer. In the IPv4-Only Edge peering architecture the PE is
IPv4-Only as all PE-CE interfaces are IPv4-Only. However, on the CE,
the PE-CE interface is the only interface that is IPv4-Only and all
other interfaces may or may not be IPv4-Only. Following the data
plane packet flow, IPv6 packets are forwarded from the ingress CE to
the IPv4-Only ingress PE where the VPN label imposition push per
prefix, per-vrf, per-CE occurs and the labeled packet is forwarded
over a 4to6 softwire IPv6-Only core, to the egress PE where the VPN
label disposition pop occurs and the native IPv6 packet is forwarded
to the egress CE. In the reverse direction IPv6 packets are
forwarded from the egress CE to egress PE where the VPN label
imposition per prefix, per-vrf, per-CE push occurs and the labeled
packet is forwarded back over the 4to6 softwire IPv6-Only core, to
the ingress PE where the VPN label disposition pop occurs and the
native IPv6 packet is forwarded to the ingress CE. . The
functionality of the IPv4 forwarding plane in this scenario is
identical from a data plane forwarding perspective to Dual Stack IPv4
/ IPv6 forwarding scenario.
Mishra, et al. Expires 8 May 2024 [Page 23]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
+--------+ +--------+
| IPv4 | | IPv4 |
| Client | | Client |
| Network| | Network|
+--------+ +--------+
| \ / |
| \ / |
| \ / |
| X |
| / \ |
| / \ |
| / \ |
+--------+ +--------+
| AFBR | | AFBR |
+--| IPv4/6 |---| IPv4/6 |--+
| +--------+ +--------+ |
+--------+ | | +--------+
| IPv6 | | | | IPv6 |
| Client | | | | Client |
| Network|------| IPv6 |-------| Network|
+--------+ | only | +--------+
| |
| +--------+ +--------+ |
+--| AFBR |---| AFBR |--+
| IPv4/6 | | IPv4/6 |
+--------+ +--------+
| \ / |
| \ / |
| \ / |
| X |
| / \ |
| / \ |
| / \ |
+--------+ +--------+
| IPv4 | | IPv4 |
| Client | | Client |
| Network| | Network|
+--------+ +--------+
Figure 9: 4to6 Softwire - IPv4 Edge over an IPv6-Only Core Packet
Walk
Mishra, et al. Expires 8 May 2024 [Page 24]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
9. IPv6-Only PE Design ALL SAFI RFC8950 Applicability
9.1. IPv6-Only Edge Peering design next-hop encoding
This section describes [RFC8950] next hop encoding applicability to
this specification. IPv6-only eBGP Edge PE-CE peering to carry IPv4
Unicast NLRI <AFI/SAFI> IPv4 <1/1> over an IPv6 next hop BGP
capability extended hop encoding IANA capability codepoint value 5
defined is applicable to both [RFC5549] and [RFC8950] as IPv4 Unicast
NLRI <AFI/SAFI> IPv4 <1/1> does not change in the RFC updates.
IPv4 packets over an IPv6-Only core 4to6 Softwire E2E packet flow is
part of the IPv6-Only design vendor interoperaiblity test cases and
in that respect is applicable as [RFC8950] updates [RFC5549] with RD
equal 0 change for <AFI/SAFI> VPN-IPV4 <1/128>, and Multicasat VPN
<1/129>
9.2. RFC8950 updates to RFC5549 applicability
This section describes the [RFC8950] next hop encoding updates to
[RFC5549]
In [RFC5549] when AFI/SAFI 1/128 is used, the next-hop address is
encoded as an IPv6 address with a length of 16 or 32 bytes. This
document modifies how the next-hop address is encoded to accommodate
all existing implementations and bring consistency with VPNv4oIPv4
and VPNv6oIPv6 including RD field set to 0 which was missing in
[RFC5549]. The next-hop address is now encoded as a VPN-IPv6 address
with a length of 24 or 48 bytes [RFC8950]. Updates to [RFC8950] is
applicable to the IPv6-Only PE-CE edge design for the IPv6 next hop
encoding E2E test case of IPv4 packets over and IPv6-Only core 4to6
Softwire. In this test case IPv4 Unicast NLRI <AFI/SAFI> IPv4 <1/1>
is advertised over the PE to RR core peering 4to6 softwire in <AFI/
SAFI> VPN-IPV4 <1/128>, and Multicasat VPN <1/129>
[RFC5549] next hop encoding of MP_REACH_NLRI with:
* NLRI= NLRI as per current AFI/SAFI definition
Advertising with [RFC4760] MP_REACH_NLRI with:
* AFI = 1
* SAFI = 128 or 129
* Length of Next Hop Address = 16 or 32
* NLRI= NLRI as per current AFI/SAFI definition
Mishra, et al. Expires 8 May 2024 [Page 25]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
[RFC8950] next hop encoding of MP_REACH_NLRI with:
* NLRI= NLRI as per current AFI/SAFI definition
Advertising with [RFC4760] MP_REACH_NLRI with:
* AFI = 1
* SAFI = 128 or 129
* Length of Next Hop Address = 24 or 48
* Next Hop Address = VPN-IPv6 address of next hop with an 8-octet RD
set to zero (potentially followed by the link-local VPN-IPv6
address of the next hop with an 8-octet RD is set to zero).
* NLRI= NLRI as per current AFI/SAFI definition
10. IPv4 Next Hop Encoding
* RFC 4798 (6PE) section 2 defines how the next hop should be
encoded for IPv6 NLRI over an IPv4 next hop using IPv4 mapped IPv6
address ::FFFF:192.168.1.1.
* RFC 4659 BGP MPLS VPNs section 3.2.1.2 defines VPN SAFI next hop
encoding of IPv4 mapped IPv6 address ::FFFF:192.168.1.1.
* RFC 5549 and now updated by RFC 8950 defines the IPv6 next hop
encoding to carry IPv4 NLRI over an IPv6 next hop. The IPv6 next
hop encoding defined is not an IPv6 mapped IPv4 address. The IPv6
next hop encoding is 16/32 byte for Unicast SAFI 1, Multicast SAFI
2 and BGP-LU SAFI 4, and 24/48 byte for VPN SAFI 128, MVPN SAFI
129. The IANA BGP Capability codepoint defined with RFC 5549 is
value 5 for Extended Next hop encoding.
* The industry implementation uses a mix of IPv4 mapped IPv6 address
for IPv6 NLRI carried over an IPv4 address next hop and uses 4
byte field for IPv4 next hop address for Unicast SAFI 1, Multicast
SAFI2 and BGP-LU SAFI 4, and 12 byte next hop field, 4 byte IPv4
address plus 8 byte RD (Route Distinguisher) set to 0 for VPN SAFI
128, MVPN SAFI 129.
* This draft standardizes the encoding to use an IPv4 address next
hop and uses 4 byte field for IPv4 next hop address for Unicast
SAFI 1, Multicast SAFI2 and BGP-LU SAFI 4, and 12 byte next hop
field, 4 byte IPv4 address plus 8 byte RD (Route Distinguisher)
set to 0 for VPN SAFI 128, MVPN SAFI 129.
Mishra, et al. Expires 8 May 2024 [Page 26]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
* This draft standardizes that encoding to ensure interoperability
with IANA BGP Capability codepoint allocation thus providing
parity between the RFC 5549/RFC 8950 IPv6 next hop encoding where
the next hop address follows the underlay core protocol which is
an IPv6 core and how the next hop here being an IPv6 address and
not following the NLRI protocol with IPv6 mapped IPv4 address.
Now with this draft the next hop encoding follows the underlay
core which is an IPv4 core and so now the next hop being an IPv4
address and not following the NLRI with an IPv4 mapped IPv6
address. So this parity between IPv4 next encoding and IPv6 next
hop encoding savings in OPEX and operations troubleshooting as
well as interoperability that all vendor implementations now use
the same IPv4 next hop encoding is the reason the encoding must be
standardized.
* This IPv4 next hop encoding is applicable for IPv6 NLRI for both
iBGP control plane (CP) peering as well as eBGP PE-CE, PE-PE in-
line control / data plane (CP-DP) peering which is used for
IPv4-Only PE design as well as any IPv4 peering. The IPv4 Next
hop encoding updates both RFC 4271 next hop path attribute and RFC
MP-BGP RFC 4760 NLRI path attribute.
* Some of the major vendors across platforms even support a variety
of different encodings as well in some cases on the same platform
the control plane BGP encoding and hardware programming is even
differnet and does not match up.
* For interoperability if a vendor does not support the new next hop
encoding, it would continue to use the IPv4 mapped IPv6 address
format until the P2P send / receive neighbors MP-BGP MP_REACH BGP
capability exchange is for the new IPv4 Next hop encoding
codepoint.
11. IPv6-Only PE Design for ALL AFI/SAFI
Listed below are the following IPv6-Only PE Design, design scenario's
that have been tested with test results related to the 3 of the Most
Common SAFIs used today listed below:
<AFI/SAFI> IPv4 Unicast <1/1>, IPv6 Unicast <2/1>, VPN-IPV4 <1/128>,
VPN-IPV6 <2/128>, Multicasat VPN <1/129>, Multicasat VPN <2/129>,BGP-
LU IPV4 (GRT) <1/4>
IPv6-Only PE Design Proof of conept interoperability testing of the 3
most common SAFI with 12 of the most common design use cases between
the 5 vendors Cisco, Juniper, Arista, Nokia and Huawei.
Mishra, et al. Expires 8 May 2024 [Page 27]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
Cisco, Juniper, Arista, Nokia, Huawei, platform, code revision and
test results for all use cases
Cisco: Edge Router- XR ASR 9910 IOS XR 7.4.1, Core Router- NCS 6000
7.2.2, CRS-X 6.7.4
Juniper: Edge Router- MX platform MX480, MX960, Core Router- PTX
Platform PTX5000, PTC10K8 (JUNOS and EVO) Release 20.4R2
Tested v4 edge over v6 core in a virtual setup using vMX platforrm
and 20.4R2 and LDPv6 as underlay, but there were some data plane
forwarding issues. Tested same setup on latest release 21.4 and it
worked. Investigating what the minimum version is for this setup to
work.
Tested on above Juniper platforms. Completed IPv6-Only PE design
functionality test with PE-CE IPv6 peer carrying IPv4 and IPv6
prefixes control plane validation and data plane forwarding plane
validation and verified end to end reachability CE to CE forwarding
plane with Default Per-CE label allocation mode. Tested with
IPv4-Only Core and IPv6-Only Core and proved that the IPv6-Only PE
design solution works. Both IPv4 and IPv6 packets were forwarded
identical functionality of Dual Stack without having IPv4 address
configured.
Nokia: Edge and Core-7750 Service Router, Release R21
Huawei: Edge and Core-VRPv8, Release VRP-V800R020C10
Arista:
Intra-AS tests PE-CE Edge Peering IPv4-Only Core, IPv6-Only Core,
Global Table (GRT) and IP VPN
AFI/SAFI IPv4-Unicast SAFI IPv6-Unicast SAFI
IPv4 Core:
Test-1 Global table (6PE)
Test-2 IP VPN
Global table IPv6
IPv6 Core:
Test-3 Global table
Mishra, et al. Expires 8 May 2024 [Page 28]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
Test-4 IP VPN
Inter-AS Options tests IPv4-Only Core, IPv6-Only Core, Global
Table (GRT) and IP VPN
AFI/SAFI VPN and MVPN
IPv4-Only Core
Test-5 Global table 6PE Option-B (Segmented LSP stitched IPv4 Core -
Inter-AS Link IPv6-Only PE - IPv4 Core)
Test-6 Global table 6PE Option-C (Redistribute IPv4 Loopbacks into
BGP-LU AFI/SAFI 2/6)
Test-7 IP VPN Inter AS Option-B (Segmented LSP stitched IPv4 Core -
Inter-AS Link IPv6-Only PE - IPv4 Core)
Test-8 IP VPN Inter AS Option-C (Redistribute IPv4 Loopbacks into
BGP-LU AFI/SAFI 2/6)
IPv6-Only Core
Test-9 Global table Option-B
Test-10 Global table Option-C
Test-11 IP VPN Inter AS Option-B
Test-12 IP VPN Inter AS Option-C
11.1. IPv6-Only PE Design All SAFI Case-1 E2E IPv6-Only PE-CE, Global
Table over IPv4-Only Core(6PE)
Mishra, et al. Expires 8 May 2024 [Page 29]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
________
IPv6-Only _____ / \ IPv6-Only
PE / CE / \__/ \___ PE / CE
+----+ +----+ / \ +------+ +-----+
| | | | | |_ | | | |
| | | | | \ | | | |
| CE |--| PE |--\ IPv4-Only Core |----| PE |---| CE |
| | | | \0=========Underlay =======0| | | | |
+----+ +----+ \ __/ +------+ +-----+
IPv6 BGP peer \ MPLS / SR domain / IPv6 BGP peer
IPv4 forwarding \__ __ / IPv4 forwarding
IPv6 forwarding \_______/ \_____/ IPv6 forwarding
Figure 10: Design Solution-1 E2E IPv6-Only PE-CE, Global
Table over IPv4-Only Core (6PE)
11.2. IPv6-Only PE Design All SAFI Case-2 E2E IPv6-Only PE-CE, VPN over
IPv4-Only Core
________
IPv6-Only _____ / \ IPv6-Only
PE / CE / \__/ \___ PE / CE
+----+ +----+ / \ +------+ +-----+
| | | | | 0====VPN Overlay Tunnel ==0| | | | |
| | | | | \ | | | |
| CE |--| PE |--\ IPv4-Only Core |----| PE |---| CE |
| | | | \0=========Underlay =======0| | | | |
+----+ +----+ \ __/ +------+ +-----+
IPv6 BGP peer \ MPLS / SR domain / IPv6 BGP peer
IPv4 forwarding \__ __ / IPv4 forwarding
IPv6 forwarding \_______/ \_____/ IPv6 forwarding
Figure 11: Design Solution-2 E2E IPv6-Only PE-CE, VPN over
IPv4-Only Core
11.3. IPv6-Only PE Design All SAFI Case-3 E2E IPv6-Only PE-CE, Global
Table over IPv6-Only Core (4PE)
Mishra, et al. Expires 8 May 2024 [Page 30]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
________
IPv6-Only _____ / \ IPv6-Only
PE / CE / \__/ \___ PE / CE
+----+ +----+ / \ +------+ +-----+
| | | | | |_ | | | |
| | | | | \ | | | |
| CE |--| PE |--\ IPv6-Only Core |----| PE |---| CE |
| | | | \0=========Underlay =======0| | | | |
+----+ +----+ \ __/ +------+ +-----+
IPv6 BGP peer \ MPLS / SR domain / IPv6 BGP peer
IPv4 forwarding \__ __ / IPv4 forwarding
IPv6 forwarding \_______/ \_____/ IPv6 forwarding
Figure 12: Design Solution-3 E2E IPv6-Only PE-CE, Global
Table over IPv6-Only Core (4PE)
11.4. IPv6-Only PE Design All SAFI Case-4 E2E IPv6-Only PE-CE, VPN over
IPv6-Only Core
________
IPv6-Only _____ / \ IPv6-Only
PE / CE / \__/ \___ PE / CE
+----+ +----+ / \ +------+ +-----+
| | | | | 0====VPN Overlay Tunnel ==0| | | | |
| | | | | \ | | | |
| CE |--| PE |--\ IPv6-Only Core |----| PE |---| CE |
| | | | \0=========Underlay =======0| | | | |
+----+ +----+ \ __/ +------+ +-----+
IPv6 BGP peer \ MPLS / SR domain / IPv6 BGP peer
IPv4 forwarding \__ __ / IPv4 forwarding
IPv6 forwarding \_______/ \_____/ IPv6 forwarding
Figure 13: Design Solution-4 E2E IPv6-Only PE-CE, VPN over
IPv6-Only Core
11.5. IPv6-Only PE Design All SAFI Case-5 E2E IPv6-Only PE-CE, Global
Table over IPv4-Only Core(6PE) - Inter-AS Option-B
Mishra, et al. Expires 8 May 2024 [Page 31]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv4-Only Core|----|IPv4-Only Core|--|PE|-|CE|
| | | | |0=Underlay==0 | |0==Underlay==0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 14: Design Solution-5 E2E IPv6-Only PE-CE, Global
Table over IPv4-Only Core (6PE) - Inter-AS Option-B
11.6. IPv6-Only PE Design All SAFI Case-6 E2E IPv6-Only PE-CE, Global
Table over IPv4-Only Core(6PE) - Inter-AS Option-C
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv4-Only Core|----|IPv4-Only Core|--|PE|-|CE|
| | | | |0=Underlay==0 | |0==Underlay==0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 15: Design Solution-6 E2E IPv6-Only PE-CE, Global
Table over IPv4-Only Core (6PE) - Inter-AS Option-C
11.7. IPv6-Only PE Design All SAFI Case-7 E2E IPv6-Only PE-CE, VPN over
IPv4-Only - Inter-AS Option-B
Mishra, et al. Expires 8 May 2024 [Page 32]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv4-Only Core|----|IPv4-Only Core|--|PE|-|CE|
| | | | |0=Overlay===0 | |0==Overlay===0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 16: Design Solution-7 E2E IPv6-Only PE-CE, VPN over
IPv4-Only Core - Inter-AS Option-B
11.8. IPv6-Only PE Design All SAFI Case-8 E2E IPv6-Only PE-CE, VPN over
IPv4-Only Core - Inter-AS Option-C
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv4-Only Core|----|IPv4-Only Core|--|PE|-|CE|
| | | | |0=Overlay===0 | |0==Overlay===0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 17: Design Solution-8 E2E IPv6-Only PE-CE, VPN over
IPv4-Only Core - Inter-AS Option-C
11.9. IPv6-Only PE Design All SAFI Case-9 E2E IPv6-Only PE-CE, Global
Table over IPv6-Only Core - Inter-AS Option-B
Mishra, et al. Expires 8 May 2024 [Page 33]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv6-Only Core|----|IPv6-Only Core|--|PE|-|CE|
| | | | |0=Underlay==0 | |0==Underlay==0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 18: Design Solution-9 E2E IPv6-Only PE-CE, Global
Table over IPv6-Only Core - Inter-AS Option-B
11.10. IPv6-Only PE Design All SAFI Case-10 E2E IPv6-Only PE-CE, Global
Table over IPv6-Only Core - Inter-AS Option-C
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv6-Only Core|--- |IPv6-Only Core|--|PE|-|CE|
| | | | |0=Underlay==0 | |0==Underlay==0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 19: Design Solution-10 E2E IPv6-Only PE-CE, Global
Table over IPv6-Only Core - Inter-AS Option-C
11.11. IPv6-Only PE Design All SAFI Case-4 E2E IPv6-Only PE-CE, VPN
over IPv6-Only Core - Inter-AS Option-B
Mishra, et al. Expires 8 May 2024 [Page 34]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv6-Only Core|--- |IPv6-Only Core|--|PE|-|CE|
| | | | |0=Overlay===0 | |0==Overlay===0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 20: Design Solution-11 E2E IPv6-Only PE-CE, VPN over
IPv6-Only Core - Inter-AS Option-B
11.12. IPv6-Only PE Design All SAFI Case-12 E2E IPv6-Only PE-CE, VPN
over IPv6-Only Core - Inter-AS Option-C
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv6-Only Core|--- |IPv6-Only Core|--|PE|-|CE|
| | | | |0=Overlay===0 | |0==Overlay===0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 21: Design Solution-12 E2E IPv6-Only PE-CE, VPN over
IPv6-Only Core - Inter-AS Option-C
11.13. IPv6-Only PE-CE Operational Considerations Testing
Mishra, et al. Expires 8 May 2024 [Page 35]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
Ping CE to PE when destination prefix is withdrawn
Traceroute CE to PE and test all ICMPv4 and ICMPv6 type codes
+-------+ +-------+
| | IPv6 Only | |
| CE |----------------| PE |
| | IPv6 BGP Peer | |
+-------+ +-------+
IPv4 forwarding IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 22: Ping and Trace Test Case IPv6-Only PE Design
12. IPv4-Only PE Design for ALL AFI/SAFI
Listed below are the following IPv4-Only PE Design, design scenario's
that have been tested with test results related to the 3 of the Most
Common SAFIs used today listed below:
<AFI/SAFI> IPv4 Unicast <1/1>, IPv6 Unicast <2/1>, VPN-IPV4 <1/128>,
VPN-IPV6 <2/128>, Multicasat VPN <1/129>, Multicasat VPN <2/129>,BGP-
LU IPV4 (GRT) <1/4>
IPv4-Only PE Design Proof of conept interoperability testing of the 3
most common SAFI with 12 of the most common design use cases between
the 5 vendors Cisco, Juniper, Arista, Nokia and Huawei.
Cisco, Juniper, Arista, Nokia, Huawei, platform, code revision and
test results for all use cases
Cisco: Edge Router- XR ASR 9910 IOS XR 7.4.1, Core Router- NCS 6000
7.2.2, CRS-X 6.7.4
Juniper: Edge Router- MX platform MX480, MX960, Core Router- PTX
Platform PTX5000, PTC10K8 (JUNOS and EVO) Release 20.4R2
Nokia: Edge and Core-7750 Service Router, Release R21
Huawei: Edge and Core-VRPv8, Release VRP-V800R020C10
Arista:
Intra-AS tests PE-CE Edge Peering IPv4-Only Core, IPv6-Only Core,
Global Table (GRT) and IP VPN
AFI/SAFI IPv4-Unicast SAFI IPv6-Unicast SAFI
Mishra, et al. Expires 8 May 2024 [Page 36]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
IPv4 Core:
Test-1 Global table (6PE)
Test-2 IP VPN
Global table IPv6
IPv6 Core:
Test-3 Global table
Test-4 IP VPN
Inter-AS Options tests IPv4-Only Core, IPv6-Only Core, Global
Table (GRT) and IP VPN
AFI/SAFI VPN and MVPN
IPv4-Only Core
Test-5 Global table 6PE Option-B (Segmented LSP stitched IPv4 Core -
Inter-AS Link IPv6-Only PE - IPv4 Core)
Test-6 Global table 6PE Option-C (Redistribute IPv4 Loopbacks into
BGP-LU AFI/SAFI 2/6)
Test-7 IP VPN Inter AS Option-B (Segmented LSP stitched IPv4 Core -
Inter-AS Link IPv6-Only PE - IPv4 Core)
Test-8 IP VPN Inter AS Option-C (Redistribute IPv4 Loopbacks into
BGP-LU AFI/SAFI 2/6)
IPv6-Only Core
Test-9 Global table Option-B
Test-10 Global table Option-C
Test-11 IP VPN Inter AS Option-B
Test-12 IP VPN Inter AS Option-C
12.1. IPv4-Only PE Design All SAFI Case-1 E2E IPv4-Only PE-CE, Global
Table over IPv4-Only Core(6PE)
Mishra, et al. Expires 8 May 2024 [Page 37]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
________
IPv4-Only _____ / \ IPv4-Only
PE / CE / \__/ \___ PE / CE
+----+ +----+ / \ +------+ +-----+
| | | | | |_ | | | |
| | | | | \ | | | |
| CE |--| PE |--\ IPv4-Only Core |----| PE |---| CE |
| | | | \0=========Underlay =======0| | | | |
+----+ +----+ \ __/ +------+ +-----+
IPv4 BGP peer \ MPLS / SR domain / IPv4 BGP peer
IPv4 forwarding \__ __ / IPv4 forwarding
IPv6 forwarding \_______/ \_____/ IPv6 forwarding
Figure 23: Design Solution-1 E2E IPv4-Only PE-CE, Global
Table over IPv4-Only Core (6PE)
12.2. IPv4-Only PE Design All SAFI Case-2 E2E IPv4-Only PE-CE, VPN over
IPv4-Only Core
________
IPv4-Only _____ / \ IPv4-Only
PE / CE / \__/ \___ PE / CE
+----+ +----+ / \ +------+ +-----+
| | | | | 0====VPN Overlay Tunnel ==0| | | | |
| | | | | \ | | | |
| CE |--| PE |--\ IPv4-Only Core |----| PE |---| CE |
| | | | \0=========Underlay =======0| | | | |
+----+ +----+ \ __/ +------+ +-----+
IPv4 BGP peer \ MPLS / SR domain / IPv4 BGP peer
IPv4 forwarding \__ __ / IPv4 forwarding
IPv6 forwarding \_______/ \_____/ IPv6 forwarding
Figure 24: Design Solution-2 E2E IPv4-Only PE-CE, VPN over
IPv4-Only Core
Huawei: Edge and Core-VRPv8, Release VRP-V800R020C10
12.3. IPv4-Only PE Design All SAFI Case-3 E2E IPv4-Only PE-CE, Global
Table over IPv6-Only Core (4PE)
Mishra, et al. Expires 8 May 2024 [Page 38]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
________
IPv4-Only _____ / \ IPv4-Only
PE / CE / \__/ \___ PE / CE
+----+ +----+ / \ +------+ +-----+
| | | | | |_ | | | |
| | | | | \ | | | |
| CE |--| PE |--\ IPv4-Only Core |----| PE |---| CE |
| | | | \0=========Underlay =======0| | | | |
+----+ +----+ \ __/ +------+ +-----+
IPv4 BGP peer \ MPLS / SR domain / IPv4 BGP peer
IPv4 forwarding \__ __ / IPv4 forwarding
IPv6 forwarding \_______/ \_____/ IPv6 forwarding
Figure 25: Design Solution-3 E2E IPv4-Only PE-CE, Global
Table over IPv6-Only Core (4PE)
12.4. IPv4-Only PE Design All SAFI Case-4 E2E IPv4-Only PE-CE, VPN over
IPv6-Only Core
________
IPv4-Only _____ / \ IPv4-Only
PE / CE / \__/ \___ PE / CE
+----+ +----+ / \ +------+ +-----+
| | | | | 0====VPN Overlay Tunnel ==0| | | | |
| | | | | \ | | | |
| CE |--| PE |--\ IPv4-Only Core |----| PE |---| CE |
| | | | \0=========Underlay =======0| | | | |
+----+ +----+ \ __/ +------+ +-----+
IPv4 BGP peer \ MPLS / SR domain / IPv4 BGP peer
IPv4 forwarding \__ __ / IPv4 forwarding
IPv6 forwarding \_______/ \_____/ IPv6 forwarding
Figure 26: Design Solution-4 E2E IPv4-Only PE-CE, VPN over
IPv6-Only Core
12.5. IPv4-Only PE Design All SAFI Case-5 E2E IPv4-Only PE-CE, Global
Table over IPv4-Only Core(6PE) - Inter-AS Option-B
Mishra, et al. Expires 8 May 2024 [Page 39]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv4-Only Core|----|IPv4-Only Core|--|PE|-|CE|
| | | | |0=Underlay==0 | |0==Underlay==0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 27: Design Solution-5 E2E IPv4-Only PE-CE, Global
Table over IPv4-Only Core (6PE) - Inter-AS Option-B
12.6. IPv4-Only PE Design All SAFI Case-6 E2E IPv4-Only PE-CE, Global
Table over IPv4-Only Core(6PE) - Inter-AS Option-C
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv4-Only Core|----|IPv4-Only Core|--|PE|-|CE|
| | | | |0=Underlay==0 | |0==Underlay==0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 28: Design Solution-6 E2E IPv4-Only PE-CE, Global
Table over IPv4-Only Core (6PE) - Inter-AS Option-C
12.7. IPv4-Only PE Design All SAFI Case-7 E2E IPv4-Only PE-CE, VPN over
IPv4-Only - Inter-AS Option-B
Mishra, et al. Expires 8 May 2024 [Page 40]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv4-Only Core|----|IPv4-Only Core|--|PE|-|CE|
| | | | |0=Overlay===0 | |0==Overlay===0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 29: Design Solution-7 E2E IPv4-Only PE-CE, VPN over
IPv4-Only Core - Inter-AS Option-B
12.8. IPv4-Only PE Design All SAFI Case-8 E2E IPv4-Only PE-CE, VPN over
IPv4-Only Core - Inter-AS Option-C
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv4-Only Core|----|IPv4-Only Core|--|PE|-|CE|
| | | | |0=Overlay===0 | |0==Overlay===0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 30: Design Solution-8 E2E IPv4-Only PE-CE, VPN over
IPv4-Only Core - Inter-AS Option-C
12.9. IPv4-Only PE Design All SAFI Case-9 E2E IPv4-Only PE-CE, Global
Table over IPv6-Only Core - Inter-AS Option-B
Mishra, et al. Expires 8 May 2024 [Page 41]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv6-Only Core|----|IPv6-Only Core|--|PE|-|CE|
| | | | |0=Underlay==0 | |0==Underlay==0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 31: Design Solution-9 E2E IPv4-Only PE-CE, Global
Table over IPv6-Only Core - Inter-AS Option-B
12.10. IPv4-Only PE Design All SAFI Case-10 E2E IPv4-Only PE-CE, Global
Table over IPv6-Only Core - Inter-AS Option-C
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv6-Only Core|--- |IPv6-Only Core|--|PE|-|CE|
| | | | |0=Underlay==0 | |0==Underlay==0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 32: Design Solution-10 E2E IPv4-Only PE-CE, Global
Table over IPv6-Only Core - Inter-AS Option-C
12.11. IPv4-Only PE Design All SAFI Case-11 E2E IPv4-Only PE-CE, VPN
over IPv6-Only Core - Inter-AS Option-B
Mishra, et al. Expires 8 May 2024 [Page 42]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv6-Only Core|--- |IPv6-Only Core|--|PE|-|CE|
| | | | |0=Overlay===0 | |0==Overlay===0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 33: Design Solution-11 E2E IPv4-Only PE-CE, VPN over
IPv6-Only Core - Inter-AS Option-B
12.12. IPv4-Only PE Design All SAFI Case-12 E2E IPv4-Only PE-CE, VPN
over IPv6-Only Core - Inter-AS Option-C
Inter-AS ASBR-ASBR link is IPv6-Only PE
IPv6-Only __________ __________ IPv6-Only
PE / CE / \ / \ PE / CE
+--+ +----+ / \ / \ +--+ +--+
| | | | | AS 1 \ | AS 2 \ | | | |
| | | | | \IPv6| \ | | | |
|CE|-| PE |--| IPv6-Only Core|--- |IPv6-Only Core|--|PE|-|CE|
| | | | |0=Overlay===0 | |0==Overlay===0| | | | |
+--+ +----+ \ / \ / +--+ +--+
IPv6 BGP peer \ MPLS/SR / \ MPLS/SR / IPv6 BGP peer
IPv4 forwarding \_________/ \_________/ IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 34: Design Solution-12 E2E IPv4-Only PE-CE, VPN over
IPv6-Only Core - Inter-AS Option-C
12.13. IPv4-Only PE-CE Operational Considerations Testing
Mishra, et al. Expires 8 May 2024 [Page 43]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
Ping CE to PE when destination prefix is withdrawn
Traceroute CE to PE and test all ICMPv4 and ICMPv6 type codes
+-------+ +-------+
| | IPv4 Only | |
| CE |----------------| PE |
| | IPv4 BGP Peer | |
+-------+ +-------+
IPv4 forwarding IPv4 forwarding
IPv6 forwarding IPv6 forwarding
Figure 35: Ping and Trace Test Case
13. IPv4-Only PE Design and IPv6-Only PE Design ALL AFI/SFI Operational
Considerations
With a single IPv4 Peer or IPv6 Peer carrying both IPv4 and IPv6 NLRI
there are some operational considerations in terms of what changes
and what does not change.
What does not change with a single IPv6 transport peer carrying IPv4
NLRI and IPv6 NLRI below:
Routing Policy configuration is still separate for IPv4 and IPv6
configured by capability as previously.
Layer 1, Layer 2 issues such as one-way fiber or fiber cut will
impact both IPv4 and IPv6 as previously.
If the interface is in the Admin Down state, the IPv6 peer would go
down, and IPv4 NLRI and IPv6 NLRI would be withdrawn as previously.
Changes resulting from a single IPv6 transport peer carrying IPv4
NLRI and IPv6 NLRI below:
Physical interface is no longer dual stacked.
Any change in IPv6 address or DAD state will impact both IPv4 and
IPv6 NLRI exchange.
Single BFD session for both IPv4 and IPv6 NLRI fate sharing as the
session is now tied to the transport, which now is only IPv6 address
family.
Both IPv4 and IPv6 peer now exists under the IPv6 address family
configuration.
Mishra, et al. Expires 8 May 2024 [Page 44]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
Fate sharing of IPv4 and IPv6 address family from a logical
perspective now carried over a single physical IPv6 peer.
From an operations perspective, prior to elimination of IPv4 peers,
an audit is recommended to identify and IPv4 and IPv6 peering
incongruencies that may exist and to rectify them. No operational
impacts or issues are expected with this change.
With MPLS VPN overlay, per-CE next-hop label allcoation mode where
both IPv4 and IPv6 prefixes have the same label in no table lookup
pop-n-forward mode should be taken into consideration.
14. IANA Considerations
New IANA capability codepoint is requested for next hop encoding for
IPv4 next hop applicable to all SAFI for IPv4-Only PE design Inter-AS
scenarios as well as existing Intra-AS Scenarios.
15. Security Considerations
The extensions defined in this document allow BGP to propagate
reachability information about IPv4 prefixes over an MPLS or SR
IPv6-Only core network. As such, no new security issues are raised
beyond those that already exist in BGP-4 and the use of MP-BGP for
IPv6. Both IPv4 and IPv6 peers exist under the IPv6 address family
configuration. The security features of BGP and corresponding
security policy defined in the ISP domain are applicable. For the
inter-AS distribution of IPv6 routes according to case (a) of
Section 4 of this document, no new security issues are raised beyond
those that already exist in the use of eBGP for IPv6 [RFC2545].
16. Acknowledgments
Thanks to Kaliraj Vairavakkalai, Linda Dunbar, Aijun Wang, Eduardfor
Vasilenko, Joel Harlpern, Michael McBride, Ketan Talaulikar for
review comments.
17. Contributors
The following people contributed substantive text to this document:
Mohana Sundari
EMail: mohanas@juniper.net
18. References
18.1. Normative References
Mishra, et al. Expires 8 May 2024 [Page 45]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
[I-D.ietf-bess-bgp-multicast]
Zhang, Z. J., Giuliano, L., Patel, K., Wijnands, I.,
Mishra, M. P., and A. Gulko, "BGP Based Multicast", Work
in Progress, Internet-Draft, draft-ietf-bess-bgp-
multicast-05, 27 June 2023,
<https://datatracker.ietf.org/doc/html/draft-ietf-bess-
bgp-multicast-05>.
[I-D.ietf-bess-ipv6-only-pe-design]
Mishra, G. S., Mishra, M. P., Tantsura, J., Madhavi, S.,
Yang, Q., Simpson, A., and S. Chen, "IPv6-Only PE Design
for IPv4-NLRI with IPv6-NH", Work in Progress, Internet-
Draft, draft-ietf-bess-ipv6-only-pe-design-04, 20 May
2023, <https://datatracker.ietf.org/doc/html/draft-ietf-
bess-ipv6-only-pe-design-04>.
[I-D.ietf-idr-bgp-car]
Rao, D., Agrawal, S., and Co-authors, "BGP Color-Aware
Routing (CAR)", Work in Progress, Internet-Draft, draft-
ietf-idr-bgp-car-03, 23 October 2023,
<https://datatracker.ietf.org/doc/html/draft-ietf-idr-bgp-
car-03>.
[I-D.ietf-idr-flowspec-nvo3]
Eastlake, D. E., Weiguo, H., Zhuang, S., Li, Z., and R.
Gu, "BGP Dissemination of Flow Specification Rules for
Tunneled Traffic", Work in Progress, Internet-Draft,
draft-ietf-idr-flowspec-nvo3-18, 5 July 2023,
<https://datatracker.ietf.org/doc/html/draft-ietf-idr-
flowspec-nvo3-18>.
[I-D.ietf-idr-rpd]
Li, Z., Ou, L., Luo, Y., Mishra, G. S., Chen, H., and H.
Wang, "BGP Extensions for Routing Policy Distribution
(RPD)", Work in Progress, Internet-Draft, draft-ietf-idr-
rpd-17, 30 June 2023,
<https://datatracker.ietf.org/doc/html/draft-ietf-idr-rpd-
17>.
[I-D.ietf-idr-sdwan-edge-discovery]
Dunbar, L., Majumdar, K., Hares, S., Raszuk, R., and V.
Kasiviswanathan, "BGP UPDATE for SD-WAN Edge Discovery",
Work in Progress, Internet-Draft, draft-ietf-idr-sdwan-
edge-discovery-12, 14 October 2023,
<https://datatracker.ietf.org/doc/html/draft-ietf-idr-
sdwan-edge-discovery-12>.
Mishra, et al. Expires 8 May 2024 [Page 46]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
[I-D.ietf-idr-segment-routing-te-policy]
Previdi, S., Filsfils, C., Talaulikar, K., Mattes, P., and
D. Jain, "Advertising Segment Routing Policies in BGP",
Work in Progress, Internet-Draft, draft-ietf-idr-segment-
routing-te-policy-26, 23 October 2023,
<https://datatracker.ietf.org/doc/html/draft-ietf-idr-
segment-routing-te-policy-26>.
[I-D.ietf-l3vpn-bgpvpn-auto]
Ould-Brahim, H. H., "Using BGP as an Auto-Discovery
Mechanism for VR-based Layer-3 VPNs", Work in Progress,
Internet-Draft, draft-ietf-l3vpn-bgpvpn-auto-09, 25 April
2007, <https://datatracker.ietf.org/doc/html/draft-ietf-
l3vpn-bgpvpn-auto-09>.
[I-D.ietf-lsvr-bgp-spf]
Patel, K., Lindem, A., Zandi, S., and W. Henderickx, "BGP
Link-State Shortest Path First (SPF) Routing", Work in
Progress, Internet-Draft, draft-ietf-lsvr-bgp-spf-28, 29
August 2023, <https://datatracker.ietf.org/doc/html/draft-
ietf-lsvr-bgp-spf-28>.
[I-D.mpmz-bess-mup-safi]
Murakami, T., Patel, K., Matsushima, S., Zhang, Z. J.,
Agrawal, S., and D. Voyer, "BGP Extensions for the Mobile
User Plane (MUP) SAFI", Work in Progress, Internet-Draft,
draft-mpmz-bess-mup-safi-03, 5 November 2023,
<https://datatracker.ietf.org/doc/html/draft-mpmz-bess-
mup-safi-03>.
[I-D.nalawade-kapoor-tunnel-safi]
Nalawade, G., "BGP Tunnel SAFI", Work in Progress,
Internet-Draft, draft-nalawade-kapoor-tunnel-safi-05, 29
June 2006, <https://datatracker.ietf.org/doc/html/draft-
nalawade-kapoor-tunnel-safi-05>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC2545] Marques, P. and F. Dupont, "Use of BGP-4 Multiprotocol
Extensions for IPv6 Inter-Domain Routing", RFC 2545,
DOI 10.17487/RFC2545, March 1999,
<https://www.rfc-editor.org/info/rfc2545>.
Mishra, et al. Expires 8 May 2024 [Page 47]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
[RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing
Architecture", RFC 4291, DOI 10.17487/RFC4291, February
2006, <https://www.rfc-editor.org/info/rfc4291>.
[RFC4364] Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private
Networks (VPNs)", RFC 4364, DOI 10.17487/RFC4364, February
2006, <https://www.rfc-editor.org/info/rfc4364>.
[RFC4760] Bates, T., Chandra, R., Katz, D., and Y. Rekhter,
"Multiprotocol Extensions for BGP-4", RFC 4760,
DOI 10.17487/RFC4760, January 2007,
<https://www.rfc-editor.org/info/rfc4760>.
[RFC4761] Kompella, K., Ed. and Y. Rekhter, Ed., "Virtual Private
LAN Service (VPLS) Using BGP for Auto-Discovery and
Signaling", RFC 4761, DOI 10.17487/RFC4761, January 2007,
<https://www.rfc-editor.org/info/rfc4761>.
[RFC5195] Ould-Brahim, H., Fedyk, D., and Y. Rekhter, "BGP-Based
Auto-Discovery for Layer-1 VPNs", RFC 5195,
DOI 10.17487/RFC5195, June 2008,
<https://www.rfc-editor.org/info/rfc5195>.
[RFC5492] Scudder, J. and R. Chandra, "Capabilities Advertisement
with BGP-4", RFC 5492, DOI 10.17487/RFC5492, February
2009, <https://www.rfc-editor.org/info/rfc5492>.
[RFC5747] Wu, J., Cui, Y., Li, X., Xu, M., and C. Metz, "4over6
Transit Solution Using IP Encapsulation and MP-BGP
Extensions", RFC 5747, DOI 10.17487/RFC5747, March 2010,
<https://www.rfc-editor.org/info/rfc5747>.
[RFC6037] Rosen, E., Ed., Cai, Y., Ed., and IJ. Wijnands, "Cisco
Systems' Solution for Multicast in BGP/MPLS IP VPNs",
RFC 6037, DOI 10.17487/RFC6037, October 2010,
<https://www.rfc-editor.org/info/rfc6037>.
[RFC7117] Aggarwal, R., Ed., Kamite, Y., Fang, L., Rekhter, Y., and
C. Kodeboniya, "Multicast in Virtual Private LAN Service
(VPLS)", RFC 7117, DOI 10.17487/RFC7117, February 2014,
<https://www.rfc-editor.org/info/rfc7117>.
[RFC7267] Martini, L., Ed., Bocci, M., Ed., and F. Balus, Ed.,
"Dynamic Placement of Multi-Segment Pseudowires",
RFC 7267, DOI 10.17487/RFC7267, June 2014,
<https://www.rfc-editor.org/info/rfc7267>.
Mishra, et al. Expires 8 May 2024 [Page 48]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
[RFC7432] Sajassi, A., Ed., Aggarwal, R., Bitar, N., Isaac, A.,
Uttaro, J., Drake, J., and W. Henderickx, "BGP MPLS-Based
Ethernet VPN", RFC 7432, DOI 10.17487/RFC7432, February
2015, <https://www.rfc-editor.org/info/rfc7432>.
[RFC7752] Gredler, H., Ed., Medved, J., Previdi, S., Farrel, A., and
S. Ray, "North-Bound Distribution of Link-State and
Traffic Engineering (TE) Information Using BGP", RFC 7752,
DOI 10.17487/RFC7752, March 2016,
<https://www.rfc-editor.org/info/rfc7752>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8277] Rosen, E., "Using BGP to Bind MPLS Labels to Address
Prefixes", RFC 8277, DOI 10.17487/RFC8277, October 2017,
<https://www.rfc-editor.org/info/rfc8277>.
[RFC8955] Loibl, C., Hares, S., Raszuk, R., McPherson, D., and M.
Bacher, "Dissemination of Flow Specification Rules",
RFC 8955, DOI 10.17487/RFC8955, December 2020,
<https://www.rfc-editor.org/info/rfc8955>.
[RFC9012] Patel, K., Van de Velde, G., Sangli, S., and J. Scudder,
"The BGP Tunnel Encapsulation Attribute", RFC 9012,
DOI 10.17487/RFC9012, April 2021,
<https://www.rfc-editor.org/info/rfc9012>.
[RFC9015] Farrel, A., Drake, J., Rosen, E., Uttaro, J., and L.
Jalil, "BGP Control Plane for the Network Service Header
in Service Function Chaining", RFC 9015,
DOI 10.17487/RFC9015, June 2021,
<https://www.rfc-editor.org/info/rfc9015>.
18.2. Informative References
[I-D.ietf-idr-dynamic-cap]
Chen, E. and S. R. Sangli, "Dynamic Capability for BGP-4",
Work in Progress, Internet-Draft, draft-ietf-idr-dynamic-
cap-16, 21 October 2021,
<https://datatracker.ietf.org/doc/html/draft-ietf-idr-
dynamic-cap-16>.
[RFC4659] De Clercq, J., Ooms, D., Carugi, M., and F. Le Faucheur,
"BGP-MPLS IP Virtual Private Network (VPN) Extension for
IPv6 VPN", RFC 4659, DOI 10.17487/RFC4659, September 2006,
<https://www.rfc-editor.org/info/rfc4659>.
Mishra, et al. Expires 8 May 2024 [Page 49]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
[RFC4684] Marques, P., Bonica, R., Fang, L., Martini, L., Raszuk,
R., Patel, K., and J. Guichard, "Constrained Route
Distribution for Border Gateway Protocol/MultiProtocol
Label Switching (BGP/MPLS) Internet Protocol (IP) Virtual
Private Networks (VPNs)", RFC 4684, DOI 10.17487/RFC4684,
November 2006, <https://www.rfc-editor.org/info/rfc4684>.
[RFC4798] De Clercq, J., Ooms, D., Prevost, S., and F. Le Faucheur,
"Connecting IPv6 Islands over IPv4 MPLS Using IPv6
Provider Edge Routers (6PE)", RFC 4798,
DOI 10.17487/RFC4798, February 2007,
<https://www.rfc-editor.org/info/rfc4798>.
[RFC4925] Li, X., Ed., Dawkins, S., Ed., Ward, D., Ed., and A.
Durand, Ed., "Softwire Problem Statement", RFC 4925,
DOI 10.17487/RFC4925, July 2007,
<https://www.rfc-editor.org/info/rfc4925>.
[RFC5549] Le Faucheur, F. and E. Rosen, "Advertising IPv4 Network
Layer Reachability Information with an IPv6 Next Hop",
RFC 5549, DOI 10.17487/RFC5549, May 2009,
<https://www.rfc-editor.org/info/rfc5549>.
[RFC5565] Wu, J., Cui, Y., Metz, C., and E. Rosen, "Softwire Mesh
Framework", RFC 5565, DOI 10.17487/RFC5565, June 2009,
<https://www.rfc-editor.org/info/rfc5565>.
[RFC6074] Rosen, E., Davie, B., Radoaca, V., and W. Luo,
"Provisioning, Auto-Discovery, and Signaling in Layer 2
Virtual Private Networks (L2VPNs)", RFC 6074,
DOI 10.17487/RFC6074, January 2011,
<https://www.rfc-editor.org/info/rfc6074>.
[RFC6513] Rosen, E., Ed. and R. Aggarwal, Ed., "Multicast in MPLS/
BGP IP VPNs", RFC 6513, DOI 10.17487/RFC6513, February
2012, <https://www.rfc-editor.org/info/rfc6513>.
[RFC6514] Aggarwal, R., Rosen, E., Morin, T., and Y. Rekhter, "BGP
Encodings and Procedures for Multicast in MPLS/BGP IP
VPNs", RFC 6514, DOI 10.17487/RFC6514, February 2012,
<https://www.rfc-editor.org/info/rfc6514>.
[RFC8126] Cotton, M., Leiba, B., and T. Narten, "Guidelines for
Writing an IANA Considerations Section in RFCs", BCP 26,
RFC 8126, DOI 10.17487/RFC8126, June 2017,
<https://www.rfc-editor.org/info/rfc8126>.
Mishra, et al. Expires 8 May 2024 [Page 50]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
[RFC8950] Litkowski, S., Agrawal, S., Ananthamurthy, K., and K.
Patel, "Advertising IPv4 Network Layer Reachability
Information (NLRI) with an IPv6 Next Hop", RFC 8950,
DOI 10.17487/RFC8950, November 2020,
<https://www.rfc-editor.org/info/rfc8950>.
Appendix A. SAFI LIST FOR PE-CE Edge Scenario
IPv4-Only PE Design and IPv6-Only PE Design listing of PE-CE Edge ALL
applicable SAFI. Here we showing the catagorization grouping by
columns of the SAFI into 2 use case categories.
* Unicst
* Multicast
+============+=================+=========+===========+===========+
| SAFI Value | Description | Unicast | Multicast | Reference |
+============+=================+=========+===========+===========+
| 1 | Unicast | Yes | No | [RFC4760] |
+------------+-----------------+---------+-----------+-----------+
| 2 | Multicast | No | Yes | [RFC2545] |
+------------+-----------------+---------+-----------+-----------+
| 78 | MCAST-TREE SAFI | No | Yes | [RFC2545] |
+------------+-----------------+---------+-----------+-----------+
Table 1: IPv4-Only PE DESIGN and IPv6-Only PE DESIGN ALL
SAFI's PE-CE Edge Scenario
IPv4-Only PE design supports 25 / 32 IANA SAFI's of which the 7 not
supported do not use AFI=1 IPv4 or AFI=2 IPv6.
Appendix B. SAFI LIST FOR Inter-AS PE-PE Scenario
IPv4-Only PE Design and IPv6-Only PE Design listing of Inter-AS PE-PE
ALL applicable SAFI. Here we show the catagorization grouping by
columns of the SAFI into 5 use case categories.
* Unicst
* Multicast
* L1-L2 VPN
* Tunnel
* BGP Policy
Mishra, et al. Expires 8 May 2024 [Page 51]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
+=====+=============+=======+=========+=====+======+======+========================================+
|SAFI |Description |Unicast|Multicast|L1-L2|Tunnel| BGP | Reference |
|Value| | | | VPN | |Policy| |
+=====+=============+=======+=========+=====+======+======+========================================+
|1 |NLRI Unicast |Yes |No |No |No |No |[RFC4760] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|2 |NLRI |No |Yes |No |No |No |[RFC4760] |
| |Multicast | | | | | | |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|4 |NLRI MPLS |Yes |No |No |No |No |[RFC8277] |
| |Laels | | | | | | |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|5 |MCAST-VPN |No |Yes |No |No |No |[RFC6514] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|6 |Dynamic Multi|No |No |Yes |No |No |[RFC7267] |
| |Segment PW | | | | | | |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|8 |MCAST-VPLS |No |Yes |No |No |No |[RFC7117] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|9 |BGP-SFC |No |No |No |No |No |[RFC9015] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|64 |Tunnel SAFI |No |No |No |Yes |No |[I-D.nalawade-kapoor-tunnel-safi] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|65 |VPLS |No |No |No |No |No |[RFC4761] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|66 |BGP MDT SAFI |NO |Yes |No |No |No |[RFC6037] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|67 |BGP 4to6 SAFI|No |No |No |Yes |No |[RFC5747] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|68 |BGP 6to4 SAFI|No |No |No |Yes |No |[RFC5747] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|69 |L1 VPN Auto |No |No |Yes |No |No |[RFC5195] |
| |Discovery | | | | | | |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|70 |BGP EVPN |No |No |No |No |No |[RFC7432] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|71 |BGP-LS |No |No |No |No |No |[RFC7752] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|72 |BGP-LS-VPN |No |No |No |No |No |[RFC7752] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|73 |SR-TE Policy |No |No |No |No |Yes |[I-D.ietf-idr-segment-routing-te-policy]|
| |SAFI | | | | | | |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|74 |SD-WAN |No |No |No |No |Yes |[I-D.ietf-idr-sdwan-edge-discovery] |
| |Capabilities | | | | | | |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|75 |Routing |No |No |No |No |No |[I-D.ietf-idr-rpd] |
| |Policy SAFI | | | | | | |
Mishra, et al. Expires 8 May 2024 [Page 52]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|77 |Tunneled |No |No |No |Yes |No |[I-D.ietf-idr-flowspec-nvo3] |
| |Traffic | | | | | | |
| |Flowspec | | | | | | |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|78 |MCAST-TREE |No |Yes |No |No |No |[I-D.ietf-bess-bgp-multicast] |
| |SAFI | | | | | | |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|79 |BGP-DPS |No |No |No |No |Yes |Arista Dynamic Path Selection |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|80 |BGP-LS-SPF |No |No |No |No |No |[I-D.ietf-lsvr-bgp-spf] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|83 |BGP CAR |No |No |No |No |Yes |[I-D.ietf-idr-bgp-car] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|84 |BGP CAR VPN |No |No |No |No |Yes |[I-D.ietf-idr-bgp-car] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|85 |BGP MUP SAFI |No |No |No |No |Yes |[I-D.mpmz-bess-mup-safi] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|128 |MPLS VPN |Yes |No |No |No |No |[RFC4364] |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|129 |MPLS |No |Yes |No |No |No |[RFC6513] |
| |Multicast VPN| | | | | | |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|132 |Route Target |Yes |No |No |No |No |[RFC4684] |
| |Constrains | | | | | | |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|133 |Dissemination|No |No |No |No |Yes |[RFC8955] |
| |of Flowspec | | | | | | |
| |Rules | | | | | | |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|134 |L3VPN |No |No |No |No |Yes |[RFC8955] |
| |Dissemination| | | | | | |
| |of Flowspec | | | | | | |
| |Rules | | | | | | |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
|140 |VPN Auto |No |No |No |No |Yes |[I-D.ietf-l3vpn-bgpvpn-auto] |
| |Discovery | | | | | | |
+-----+-------------+-------+---------+-----+------+------+----------------------------------------+
Table 2: IPv4-Only PE DESIGN and IPv6-Only PE Design ALL SAFI's
Inter-AS PE-PE Scenario
IPv6-Only PE design supports 25 / 32 IANA SAFI's of which the 7 not
supported do not use AFI=1 IPv4 or AFI=2 IPv6.
Authors' Addresses
Mishra, et al. Expires 8 May 2024 [Page 53]
Internet-Draft IPv4-Only and IPv6-Only PE Design DESIGN November 2023
Gyan Mishra
Verizon Inc.
Email: gyan.s.mishra@verizon.com
Mankamana Mishra
Cisco Systems
821 Alder Drive,
MILPITAS
Email: mankamis@cisco.com
Jeff Tantsura
Microsoft, Inc.
Email: jefftant.ietf@gmail.com
Sudha Madhavi
Juniper Networks, Inc.
Email: smadhavi@juniper.net
Qing Yang
Arista Networks
Email: qyang@arista.com
Adam Simpson
Nokia
Email: adam.1.simpson@nokia.com
Shuanglong Chen
Huawei Technologies
Email: chenshuanglong@huawei.com
Mishra, et al. Expires 8 May 2024 [Page 54]