Internet DRAFT - draft-ietf-dhc-dhcpv6-reconfigure-rebind
draft-ietf-dhc-dhcpv6-reconfigure-rebind
Network Working Group D. Evans
Internet-Draft ARRIS International, Inc.
Intended status: Standards Track R. Droms
Updates: 3315 Cisco Systems, Inc.
Expires: October 18, 2012 S. Jiang
Huawei Technologies Co., Ltd
April 16, 2012
Rebind Capability in DHCPv6 Reconfigure Messages
draft-ietf-dhc-dhcpv6-reconfigure-rebind-10.txt
Abstract
This document updates RFC 3315 (DHCPv6) to allow the Rebind message
type to appear in the Reconfigure Message option of a Reconfigure
message. It extends the Reconfigure message to allow a DHCPv6 server
to cause a DHCPv6 client to send a Rebind message. The document also
clarifies how a DHCPv6 client responds to a received Reconfigure
message.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on October 18, 2012.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
Evans, et al. Expires October 18, 2012 [Page 1]
Internet-Draft DHCPv6 Reconfigure with Rebind April 2012
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Evans, et al. Expires October 18, 2012 [Page 2]
Internet-Draft DHCPv6 Reconfigure with Rebind April 2012
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. The Reconfigure Message option of the DHCPv6 Reconfigure
Message . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Server Behavior . . . . . . . . . . . . . . . . . . . . . . . 5
5. Client Behavior . . . . . . . . . . . . . . . . . . . . . . . 8
6. Clarification of section 19.4.2, RFC 3315 . . . . . . . . . . 9
7. Security Considerations . . . . . . . . . . . . . . . . . . . 9
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 9
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 10
10. Change log [RFC Editor please remove] . . . . . . . . . . . . 10
11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 10
11.1. Normative References . . . . . . . . . . . . . . . . . . 10
11.2. Informative References . . . . . . . . . . . . . . . . . 10
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 11
Evans, et al. Expires October 18, 2012 [Page 3]
Internet-Draft DHCPv6 Reconfigure with Rebind April 2012
1. Introduction
DHCPv6 [RFC3315] allows a server to send an unsolicited Reconfigure
message to a client. The client's response to a Reconfigure message,
according to section 19 of RFC 3315 is either a Renew or an
Information-Request message, depending on the contents of the msg-
type field in the Reconfigure Message option of the Reconfigure
message. If the client sends a Renew message, it includes a Server
Identifier option in the Renew message to specify the server that
should respond to the Renew message. The RFC 3315 specification is
only suitable for the scenarios that client would communicate with
the same DHCPv6 servers.
There are also scenarios that the client must communicate with a
different server: for example, a network administrator may choose to
shut down a DHCPv6 server and move these clients who most recently
communicated with it to another different server. Hence, this
document expands the allowed values of the message type field with in
reconfiguration message to allow the server to indicate the client to
send a Rebind message, which does not include a Server Identifier
option and allows any server to respond to the client.
RFC 3315 does not specify that a Reconfigure message must be sent
from the server with which the client most recently communicated, and
it does not specify which server the client should identify with a
Server Identifier option when the client responds to the Reconfigure
message. This document clarifies that the client should send a Renew
message in response to a Reconfigure message with a Server Identifier
option identifying the same server that the client would have
identified if the client had sent the Renew message after expiration
of the timer T1.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
This document uses IPv6 and DHCPv6 terms as defined in section 4 of
[RFC3315].
3. The Reconfigure Message option of the DHCPv6 Reconfigure Message
This section modifies section 22.19 of RFC 3315 to allow the
specification of the Rebind message in a Reconfigure message.
Evans, et al. Expires October 18, 2012 [Page 4]
Internet-Draft DHCPv6 Reconfigure with Rebind April 2012
A server includes a Reconfigure Message option in a Reconfigure
message to indicate to the client whether the client responds with a
Renew, an Information-request, or a Rebind message.
The format of this option is:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_RECONF_MSG | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| msg-type |
+-+-+-+-+-+-+-+-+
option-code OPTION_RECONF_MSG (19).
option-len 1.
msg-type 5 for Renew message, 6 for Rebind, 11 for
Information-request message.
4. Server Behavior
This section updates specific text in sections 19.1, and 19.2 of RFC
3315.
Section 19.1.1:
OLD:
The server MUST include a Reconfigure Message option (defined in
section 22.19) to select whether the client responds with a Renew
message or an Information-Request message.
The server MUST NOT include any other options in the Reconfigure
except as specifically allowed in the definition of individual
options.
A server sends each Reconfigure message to a single DHCP client,
using an IPv6 unicast address of sufficient scope belonging to the
DHCP client. If the server does not have an address to which it can
send the Reconfigure message directly to the client, the server uses
a Relay-reply message (as described in section 20.3) to send the
Reconfigure message to a relay agent that will relay the message to
the client. The server may obtain the address of the client (and the
appropriate relay agent, if required) through the information the
server has about clients that have been in contact with the server,
or through some external agent.
Evans, et al. Expires October 18, 2012 [Page 5]
Internet-Draft DHCPv6 Reconfigure with Rebind April 2012
To reconfigure more than one client, the server unicasts a separate
message to each client. The server may initiate the reconfiguration
of multiple clients concurrently; for example, a server may send a
Reconfigure message to additional clients while previous
reconfiguration message exchanges are still in progress.
The Reconfigure message causes the client to initiate a Renew/Reply
or Information-request/Reply message exchange with the server. The
server interprets the receipt of a Renew or Information-request
message (whichever was specified in the original Reconfigure message)
from the client as satisfying the Reconfigure message request.
NEW:
The server MUST include a Reconfigure Message option (as defined in
Section 3) to select whether the client responds with a Renew
message, a Rebind message or an Information-Request message.
The server MUST NOT include any other options in the Reconfigure
except as specifically allowed in the definition of individual
options.
A server sends each Reconfigure message to a single DHCP client,
using an IPv6 unicast address of sufficient scope belonging to the
DHCP client. If the server does not have an address to which it can
send the Reconfigure message directly to the client, the server uses
a Relay-reply message (as described in section 20.3) to send the
Reconfigure message to a relay agent that will relay the message to
the client. The server may obtain the address of the client (and the
appropriate relay agent, if required) through the information the
server has about clients that have been in contact with the server,
or through some external agent.
To reconfigure more than one client, the server unicasts a separate
message to each client. The server may initiate the reconfiguration
of multiple clients concurrently; for example, a server may send a
Reconfigure message to additional clients while previous
reconfiguration message exchanges are still in progress.
The Reconfigure message causes the client to initiate a Renew/Reply,
a Rebind/Reply message exchange or an Information-request/Reply
message exchange. The server interprets the receipt of a Renew, a
Rebind or an Information-request message (whichever was specified in
the original Reconfigure message) from the client as satisfying the
Reconfigure message request.
Section 19.1.2:
Evans, et al. Expires October 18, 2012 [Page 6]
Internet-Draft DHCPv6 Reconfigure with Rebind April 2012
OLD:
If the server does not receive a Renew or Information-request message
from the client in REC_TIMEOUT milliseconds, the server retransmits
the Reconfigure message, doubles the REC_TIMEOUT value and waits
again. The server continues this process until REC_MAX_RC
unsuccessful attempts have been made, at which point the server
SHOULD abort the reconfigure process for that client.
NEW:
If the server does not receive a Renew, Rebind or Information-request
message from the client in REC_TIMEOUT milliseconds, the server
retransmits the Reconfigure message, doubles the REC_TIMEOUT value
and waits again. The server continues this process until REC_MAX_RC
unsuccessful attempts have been made, at which point the server
SHOULD abort the reconfigure process for that client.
Section 19.2:
OLD:
19.2. Receipt of Renew or Rebind Messages
The server generates and sends a Reply message to the client as
described in sections 18.2.3 and 18.2.8, including options for
configuration parameters.
The server MAY include options containing the IAs and new values for
other configuration parameters in the Reply message, even if those
IAs and parameters were not requested in the Renew message from the
client.
NEW:
19.2. Receipt of Renew Messages
In response to a Renew message, the server generates and sends a
Reply message to the client as described in sections 18.2.3 and
18.2.8, including options for configuration parameters.
In response to a Rebind message, the server generates and sends a
Reply message to the client as described in sections 18.2.4 and
18.2.8, including options for configuration parameters.
The server MAY include options containing the IAs and new values for
other configuration parameters in the Reply message, even if those
IAs and parameters were not requested in the Renew or Rebind message
Evans, et al. Expires October 18, 2012 [Page 7]
Internet-Draft DHCPv6 Reconfigure with Rebind April 2012
from the client.
5. Client Behavior
This section updates specific text in section 19.4 of RFC 3315.
Section 19.4.1:
OLD:
Upon receipt of a valid Reconfigure message, the client responds with
either a Renew message or an Information-request message as indicated
by the Reconfigure Message option (as defined in section 22.19). The
client ignores the transaction-id field in the received Reconfigure
message. While the transaction is in progress, the client silently
discards any Reconfigure messages it receives.
NEW:
Upon receipt of a valid Reconfigure message, the client responds with
a Renew message, a Rebind message or an Information-request message
as indicated by the Reconfigure Message option (as defined in Section
3). The client ignores the transaction-id field in the received
Reconfigure message. While the transaction is in progress, the
client silently discards any Reconfigure messages it receives.
Section 19.4.2:
ADD new second and third paragraphs:
When responding to a Reconfigure, the client creates and sends the
Rebind message in exactly the same manner as outlined in section
18.1.4 of RFC 3315, with the exception that the client copies the
Option Request option and any IA options from the Reconfigure message
into the Rebind message.
If a client is currently sending Rebind messages, as described in
section 18.1.4 of RFC 3315, the client ignores any received
Reconfigure messages.
Section 19.4.4:
OLD:
The client uses the same variables and retransmission algorithm as it
does with Renew or Information-request messages generated as part of
a client-initiated configuration exchange. See sections 18.1.3 and
Evans, et al. Expires October 18, 2012 [Page 8]
Internet-Draft DHCPv6 Reconfigure with Rebind April 2012
18.1.5 for details. If the client does not receive a response from
the server by the end of the retransmission process, the client
ignores and discards the Reconfigure message.
NEW:
The client uses the same variables and retransmission algorithm as it
does with Renew, Rebind or Information-request messages generated as
part of a client-initiated configuration exchange. See sections
18.1.3, 18.1.4 and 18.1.5 of RFC 3315 for details. If the client
does not receive a response from the server by the end of the
retransmission process, the client ignores and discards the
Reconfigure message.
6. Clarification of section 19.4.2, RFC 3315
When sending a Renew message in response to the receipt of a
Reconfigure message, the client MUST include a Server Identifier
option identifying the server the client most recently communicated
with.
7. Security Considerations
This document allows the Rebind message type to appear in the
Reconfigure Message option of a Reconfigure message so that the
client rebinds to a different DHCPv6 server. A malicious attacker
may use a faked Reconfigure message to force the client to disconnect
from the current server and relink to a faked server by quickly
responding to the client's Rebind message. A similar attack is
available in DHCPv6 by an attacker spoofing itself as a valid DHCPv6
server in response to a Solicit or Request message. These attacks
can be prevented by using the AUTH option [RFC3315]. DHCPv6 clients
that support Reconfigure-Rebind MUST implement the Reconfigure Key
authentication protocol as described in [RFC3315] section 21.5.
Other authentication mechanisms may optionally be implemented. For
example, the Secure DHCPv6 [I-D.ietf-dhc-secure-dhcpv6], based on
Cryptographically Generated Addresses (CGA) [RFC3972], can provide
source address ownership validation, message origin authentication
and message integrity without requesting symmetric key pairs or
supporting from any key management system.
8. Acknowledgements
Valuable comments were made by Jari Arkko, Sean Turner, Ted Lemon and
Stephen Farrell.
Evans, et al. Expires October 18, 2012 [Page 9]
Internet-Draft DHCPv6 Reconfigure with Rebind April 2012
9. IANA Considerations
There are no actions for IANA associated with this document.
10. Change log [RFC Editor please remove]
Revision -05
Clarified description of this feature in introduction.
Clarified action of client if it receives a Reconfigure while sending
Rebind messages.
Revision -08
Add a new co-author. Refreshed expired draft. Refine the motivation
and suitable scenarios, also add some new security considerations.
Correct the intended status to standard track.
Revision-10
Adopt OLD-NEW style according to IESG comment and address other IESG
comments.
11. References
11.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3315] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C.,
and M. Carney, "Dynamic Host Configuration Protocol for
IPv6 (DHCPv6)", RFC 3315, July 2003.
[RFC3972] Aura, T., "Cryptographically Generated Addresses (CGA)",
RFC 3972, March 2005.
11.2. Informative References
[I-D.ietf-dhc-secure-dhcpv6]
Jiang, S. and S. Shen, "Secure DHCPv6 Using CGAs",
draft-ietf-dhc-secure-dhcpv6-06 (work in progress),
March 2012.
Evans, et al. Expires October 18, 2012 [Page 10]
Internet-Draft DHCPv6 Reconfigure with Rebind April 2012
Authors' Addresses
D. R. Evans
ARRIS International, Inc.
IPfonix, Inc., 330 WCR 16 1/2
Longmont, CO 80504-9467
USA
Phone: +1 303.682.2412
Email: N7DR@ipfonix.com
Ralph Droms
Cisco Systems, Inc.
1414 Massachusetts Avenue
Boxborough, MA 01719
USA
Phone: +1 978.936.1674
Email: rdroms@cisco.com
Sheng Jiang
Huawei Technologies Co., Ltd
Q14, Huawei Campus, No.156 Beiqing Road
Hai-Dian District, Beijing, 100095
P.R. China
Email: jiangsheng@huawei.com
Evans, et al. Expires October 18, 2012 [Page 11]
