Internet DRAFT - draft-ietf-grow-irr-routing-policy-considerations
draft-ietf-grow-irr-routing-policy-considerations
GROW Working Group D. McPherson
Internet-Draft Verisign, Inc.
Intended status: Informational S. Amante
Expires: January 21, 2016 Apple, Inc.
E. Osterweil
Verisign, Inc.
L. Blunk
Merit Network, Inc.
D. Mitchell
Singularity Networks
July 20, 2015
IRR & Routing Policy Configuration Considerations
<draft-ietf-grow-irr-routing-policy-considerations-06>
Abstract
The purpose of this document is to catalog past issues influencing
the efficacy of Internet Routing Registries (IRR) for inter-domain
routing policy specification and application in the global routing
system over the past two decades. Additionally, it provides a
discussion regarding which of these issues are still problematic in
practice, and which are simply artifacts that are no longer
applicable but continue to stifle inter-provider policy-based
filtering adoption and IRR utility to this day.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on January 21, 2016.
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
McPherson, et al. Expires January 21, 2016 [Page 1]
Internet-Draft IRR & Routing Policy Considerations July 2015
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Background . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Historical Artifacts Influencing IRR Efficacy . . . . . . . . 4
4. Accuracy and Integrity of Data Contained within the IRR . . . 5
4.1. Lack of Resource Certification . . . . . . . . . . . . . . 5
4.2. Incentives to Maintain Data within the IRR . . . . . . . . 6
4.3. Inability for Third Parties to Remove (Stale)
Information from the IRRs . . . . . . . . . . . . . . . . 7
4.4. Lack of Authoritative IRR for Resources . . . . . . . . . 8
4.5. Client-Side Considerations . . . . . . . . . . . . . . . . 9
4.6. Conclusions with respect to Data in the IRR . . . . . . . 9
5. Operation of the IRR Infrastructure . . . . . . . . . . . . . 9
5.1. Replication of Resources Among IRRs . . . . . . . . . . . 9
5.2. Updating Routing Policies from Updated IRR Resources . . . 11
6. Historical BGP Protocol Limitations . . . . . . . . . . . . . 12
7. Historical Limitations of Routers . . . . . . . . . . . . . . 14
7.1. Incremental Updates to Policy on Routers . . . . . . . . . 14
7.2. Storage Requirements for Policy on Routers . . . . . . . . 14
7.3. Updating Configuration on Routers . . . . . . . . . . . . 15
8. Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
9. Security Considerations . . . . . . . . . . . . . . . . . . . 16
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 17
11. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 17
12. Informative References . . . . . . . . . . . . . . . . . . . . 17
McPherson, et al. Expires January 21, 2016 [Page 2]
Internet-Draft IRR & Routing Policy Considerations July 2015
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 19
McPherson, et al. Expires January 21, 2016 [Page 3]
Internet-Draft IRR & Routing Policy Considerations July 2015
1. Introduction
The purpose of this document is to catalog past issues influencing
the efficacy of Internet Routing Registries (IRR) for inter-domain
routing policy specification and application in the global routing
system over the past two decades. Additionally, it provides a
discussion regarding which of these issues still pose problems in
practice, and which are no longer obstacles, but whose perceived
drawbacks continue to stifle inter-provider policy-based filtering
support and IRR utility to this day.
2. Background
IRRs can be used to express a multitude of Internet number bindings
and policy objectives, to include bindings between an origin AS and a
given prefix, AS and community import and export policies for a given
AS, as well as AS macros (as-sets in RPSL-speak) that convey the set
of ASes for which a given AS intends to include in some common group.
As quoted from Section 7 of [RFC1787], Routing in a Multi-Provider
Internet:
While ensuring Internet-wide coordination may be more and more
difficult, as the Internet continues to grow, stability and
consistency of the Internet-wide routing could significantly
benefit if the information about routing requirements of various
organizations could be shared across organizational boundaries.
Such information could be used in a wide variety of situations
ranging from troubleshooting to detecting and eliminating
conflicting routing requirements. The scale of the Internet
implies that the information should be distributed. Work is
currently underway to establish depositories of this information
(Routing Registries), as well as to develop tools that analyze, as
well as utilize this information.
3. Historical Artifacts Influencing IRR Efficacy
The term IRR is often used, incorrectly, as a broad catch-all term to
categorize issues related to the accuracy of data in the IRR, the
Routing Policy Specification Language (RPSL) and the operational
deployment of policy (derived from RPSL contained within the IRR) to
routers. It is important to classify these issues into distinct
categories so that the reader can understand which categories of
issues are historical artifacts that are no longer applicable and
which categories of issues still exist and might be addressed by the
IETF.
McPherson, et al. Expires January 21, 2016 [Page 4]
Internet-Draft IRR & Routing Policy Considerations July 2015
The following sections will separate out challenges related to the
IRR into the following categories. First, accuracy and integrity of
data contained within the IRR. Second, the Resource Policy
Specification Language (RPSL) used to represent various types of data
in the IRR. Third, operation of the IRR infrastructure, i.e.:
synchronization of resources from one IRR to other IRRs. Finally,
the methods related to extraction of policy from the IRR and the
input plus activation of that policy within routers.
4. Accuracy and Integrity of Data Contained within the IRR
The following section will examine issues related to accuracy and
integrity of data contained within the IRR.
4.1. Lack of Resource Certification
Internet number resources include IPv4 addresses, IPv6 addresses,
Autonomous System Numbers (ASNs), and more. While these resources
are generally allocated by hierarchical authorities, a general
mechanism for formally verifying (such as through cryptographic
mechanisms) when parties have been allocated resource remains an open
challenge. We generally define such a system a Resource
Certification System, and we note that some candidate examples of how
such a general system might be implemented and deployed exist
[TASRS], [RC_HotNetsX], [RFC6480].
One of the largest weaknesses often cited with the IRR system is that
the data contained within the IRRs is out of date or lacks integrity.
This is largely attributable to the fact that existing IRR mechanisms
do not provide ways for a relying party to (cryptographically) verify
the validity of an IRR object. That is, there has never existed a
resource certification infrastructure that enables a resource holder
to authorize a particular autonomous system to originate network
layer reachability advertisements for a given IPv4 or IPv6 prefix.
It should be noted that this is not a weakness of the underlying
Routing Policy Specification Language (RPSL) [RFC2622], but rather,
was largely the result of no clear demand by the operator community
for Internet Number Resource Registries to provide sufficient
resource certification infrastructure that would enable a resource
holder to develop a cryptographic binding between, for example, a
given AS number and an IP prefix.
Another noteworthy (but slightly different) deficiency in the IRR
system is the absence of a tangible tie between the resource and the
resource holder. That is, generally there is no assurance of the
validity of objects at their creation time (except for a subset of,
for example, the RIPE IRR where RPSS [RFC2725] attests for RIPE
McPherson, et al. Expires January 21, 2016 [Page 5]
Internet-Draft IRR & Routing Policy Considerations July 2015
address holders and RIPE ASN holders). If a resource holder's
authorization cannot be certified, then consumers cannot verify
attestations made. In effect, without resource certification,
consumers are basically only certifying the assertions that the
creator / maintainer of the resource object has made (not if that
assertion is valid).
The RIPE community addressed this last issue by putting in a
foundation policy [RIPE2007-01], which requires a contractual link
between the RIPE NCC and the end user in direct assignment + ASN
assignment cases, which weren't previously covered by LIR contracts
for address allocations. There were a couple of intentions with this
policy:
1. There was an encumbrance placed in the policy for the LIR to
charge the end-user for provider independent resources. This
action created a collection mechanism for PI address resources
(IPv4 / IPv6 space, ASNs).
2. It guaranteed that all RIPE NCC allocated/assigned space would be
subject to a contractual link, and that this contractual chain
might end up actually meaning something when it came to the issue
of who made what claim about what number resource.
3. It tied into the RIPE NCC's object grandfathering policy which
ties the registration details of the end-user to the object
registered in the IRR database.
While this policy specifically addressed PI/portable space holders,
other regions address this issue, too. Further, it is indeed a
prerequisite for resource certification, though it does not directly
address the IRR deficiencies.
One of the central observations of this policy was that without a
chain-of-ownership functionality in IRR databases, the discussion of
certifying their contents becomes moot.
4.2. Incentives to Maintain Data within the IRR
A second problem with data contained in the IRRs is that the
incentives for resource holders to maintain both accurate and up-to-
date information in one, or more, IRRs; including deletion of out-of-
date or stale data from the IRRs can diminish rapidly when changing
their peering policies (such as switching transit providers).
Specifically, there is a very strong incentive for an ISP's customers
to register new routing information in the IRR, because some ISPs
enforce a strict policy that they will only build or update a
customer's prefix-lists applied to the customer's inbound eBGP
McPherson, et al. Expires January 21, 2016 [Page 6]
Internet-Draft IRR & Routing Policy Considerations July 2015
sessions based off information found within the IRRs. Unfortunately,
there is little incentive for an ISP's customers to remove out-of-
date information from an IRR, most likely attributed to the fact that
some ISPs do not use, or enforce use of, data contained within the
IRRs to automatically build incoming policy applied to customer's
eBGP sessions. For example, if a customer is terminating service
from one ISP that requires use of IRR data to build incoming policy
and, at the same time, enabling service with another ISP that does
not require use of IRR data, then that customer will likely let the
data in the IRR become stale or inaccurate.
Further, policy filters are almost exclusively generated based on the
origin AS information contained within IRR route objects and used by
providers to filter downstream transit customers. Since providers
only look for route objects containing the origin AS of their
downstream customer(s), stale route objects with historical and,
possibly, incorrect origin AS information are ignored. Assuming that
the downstream customer(s) do not continue to announce those routes
with historical, or incorrect, origin AS information in BGP to the
upstream provider, there is no significant incentive to remove them
as they do not impact offline policy filter generation nor routing on
the Internet. On the other hand, the main incentive that causes the
Service Provider to work with downstream customer(s) is when the
resultant filter list becomes too large that it is difficult for it
to be stored on-board PE routers; however, this is more practically
an operational issue with very old, legacy PE routers, not more
modern PE router hardware with more robust Control Plane Engines.
4.3. Inability for Third Parties to Remove (Stale) Information from the
IRRs
A third challenge with data contained in IRRs is that it is not
possible for IRR operators, and ISPs who use them, to proactively
remove (perceived) out-of-date or "stale" resources in an IRR, on
behalf of resource holders who may not be diligent in maintaining
this information themselves. The reason is that, according to the
Resource Policy Specification Language (RPSL) [RFC2622], only the
resource holder ('mntner') specified in a 'mnt-by' value field of an
RPSL resource is authorized to add, modify or delete their own
resources within the IRR. To address this issue, the 'auth-override'
mechanism [RFC2725] was later developed that would have enabled a
third party to update and/or remove "stale" resources from the IRR.
While it is unclear if this was ever implemented or deployed, it does
provide language semantics needed to overcome this obstacle.
Nevertheless, with such a mechanism in place, there is still a risk
that the original RPSL resource holder would not receive
notifications (via the 'notify' attribute in various RPSL resources)
McPherson, et al. Expires January 21, 2016 [Page 7]
Internet-Draft IRR & Routing Policy Considerations July 2015
about the pending or actual removal of a resource from the IRR in
time to halt that action if those resources were still being used.
In this case, if the removal of a resource was not suspended, it
could potentially result in an unintentional denial of service for
the RPSL resource holder when, for example, ISPs automatically
generated and deployed a new policy based on the newly removed
resources from the IRR, thus dropping any reachability announcement
for the removed resource in eBGP.
4.4. Lack of Authoritative IRR for Resources
According to [RFC2622], within an RPSL resource "the source attribute
specifies the registry where the object is registered." Note that
this source attribute only exists within the RPSL resource itself.
Unfortunately, given a specific resource, (e.g.: a specific IPv4 or
IPv6 prefix), most of the time it is impossible to tell a priori the
authoritative IRR where to query and retrieve an authoritative copy
of that resource.
This makes it difficult for consumers of data from the IRR to
automatically know the authoritative IRR of a resource holder, which
will contain their most up-to-date set of resources. This is
typically not a problem for an ISP that has a direct (customer)
relationship with the resource holder, because the ISP will ask the
resource holder which (authoritative) IRR to pull their resources
from on, for example, a "Customer BGP Order Form". However, third
parties that do not have a direct relationship with the resource
holder, have a difficult time attempting to infer the authoritative
IRR, preferred by the resource holder, that likely contains the most
up-to-date set of resources. As a result, it would be helpful for
third parties if there was a robust referral mechanism so that a
query to one IRR would be automatically redirected toward the
authoritative IRR for the most up-to-date and authoritative copy of
that particular resource. This problem is worked around by
individual IRR operators storing a local copy of other IRR's
resources, through periodic mirroring, which allows the individual
IRR to respond to a client's query with all registered instances of a
particular IRR resource that exist in both the local IRR and all
other IRRs. Of course, the problem with this approach is that an
individual IRR operator is under no obligation to mirror all other
IRRs and, in practice, some IRRs do not mirror the resources from all
other IRRs. This could lead to the false impression that a
particular resource is not registered or maintained at a particular
IRR. Furthermore, the authentication process of accepting updates by
any given IRR may, or may not, be robust enough to overcome
impersonation attacks. As a result, there is no rigorous assurance
that a mirrored RPSL statement was actually made by the authorized
resource holder.
McPherson, et al. Expires January 21, 2016 [Page 8]
Internet-Draft IRR & Routing Policy Considerations July 2015
4.5. Client-Side Considerations
There are no provisions in the IRR mode for ensuring the
confidentiality component for clients issuing queries. The overall
Confidentiality, Integrity, and Availability (CIA) model of the
system does lack this component, because the interface to IRRs is
over an unencrypted TCP connection to port 43. This leaves the
transaction open to inspection such that an adversary could be able
to inspect the query and the response. However, the IRR system is
intended to be composed of public policy information, and protection
of queries was not part of the protection calculus when it was
designed, though the use of Transport Layer Security (TLS) [RFC5246]
would address protections of query information.
4.6. Conclusions with respect to Data in the IRR
All of the aforementioned issues related to integrity and accuracy of
data within the IRR stem from a distinct lack of resource
certification for resources contained within the IRR. Only now is an
experimental test bed that reports to provide this function (under
the auspices of the Resource PKI [RFC6480]) being formally discussed,
which could also aid in certification of resources within the IRR.
It should be noted that the RPKI is only currently able to support
signing of Route Origin Authorization (ROA) resources that are the
equivalent of 'route' resources in the IRR. There has been some
sentiment that the RPKI currently is not scoped to address the same
set of issues and the nuanced policy applications that providers
leverage in RPSL. It is unclear if, in the future, the RPKI will be
extended to support additional resources that already exist in the
IRR, e.g.: aut-num, as-net, route-set, etc. Finally, a seemingly
equivalent resource certification specification for all resources in
the IRR has already been developed [RFC2725], however it is unclear
how widely it was ever implemented or deployed.
5. Operation of the IRR Infrastructure
5.1. Replication of Resources Among IRRs
Currently, several IRRs [IRR_LIST] use a Near-Real-Time Mirroring
(NRTM) protocol to replicate each others contents. However, this
protocol has a several weaknesses. Namely, there is no way to
validate that the copy of mirrored source is correct and
synchronization issues have often resulted. Furthermore, the NRTM
protocol does not employ any security mechanisms. The NRTM protocol
relies on a pull mechanism and is generally configured with a poll
interval of 5 to 10 minutes. There is currently no mechanism to
notify an IRR when an update has occurred in a mirrored IRR so that
McPherson, et al. Expires January 21, 2016 [Page 9]
Internet-Draft IRR & Routing Policy Considerations July 2015
an immediate update can be made.
Some providers employ a process of mirroring an instance of an IRR
that involves downloading a flat text file copy of the IRR that is
made available via FTP [RFC0959]. These FTP files are exported at
regular intervals of typically anywhere between 2 and 24 hours by the
IRRs. When a provider fetches those text files, it will process them
to identify any updates and reflect changes within its own internally
maintained database. The use of an internally maintained database is
out-of-scope of this document, but is generally used to assist with
more straightforward access to or modification of data by the IRR
operator. Providers typically employ a 24 hour cycle to pull updated
resources from IRRs. Thus, depending on when resource holders
submitted their changes to an IRR, it may take up to 24 hours for
those changes to be reflected in their policy configurations. In
practice, it appears that the RPKI will also employ a 24 hour cycle
whereby changes in resources are pushed out to other RPKI caches
[RPKI_SIZING].
IRRs originated from Section 7 of [RFC1787], specifically: "The scale
of the Internet implies that the [routing requirements] information
should be distributed." Regardless, the practical effect of an
organization maintaining its own local cache of IRR resources is an
increase in resource resiliency (due to multiple copies of the same
resource being geographically distributed), a reduction in query time
for resources and, likely, a reduction in inter-domain bandwidth
consumption and associated costs. This is particularly beneficial
when, for example, an ISP is evaluating resources in an IRR just to
determine if there are any modifications to those resources that will
ultimately be reflected in a new routing policy that will get
propagated to (edge) routers in the ISP's network. Cache locality
results in reduced inter-domain bandwidth utilization for each round
trip.
On the other hand, it is unclear from where the current provider
replication interval of 24 hours originated or even whether it still
provides enough freshness in the face of available resources,
particularly in today's environment where a typical IRR system
consists of a (multi-core) multi-GHz CPU connected to a network via a
physical connection of 100 Mbps or, more likely, higher bandwidth.
In addition, increasing bandwidth demands have shifted demand towards
circuit sizes used by ISPs to 10 Gbps, thus eliminating bandwidth as
a significant factor in the transfer of data between IRRs.
Furthermore, it should be noted that Merit's Internet Routing
Registry Daemon (IRRd) [MERIT-IRRD], uses 10 minutes as its default
for "irr_mirror_interval".
Lastly, it should be noted that [RFC2769], Routing Policy System
McPherson, et al. Expires January 21, 2016 [Page 10]
Internet-Draft IRR & Routing Policy Considerations July 2015
Replication, attempted to offer a more methodical solution for
distributed replication of resources between IRRs. It is unclear why
this RFC failed to gain traction, but it is suspected that this was
due to that specification's reliance on [RFC2725], Routing Policy
System Security, that addressed "the need to assure integrity of the
data by providing an authentication and authorization model."
Indeed, [RFC2725] attempts to add an otherwise absent security model
to the integrity of policy statements made in RPSL. Without formal
protections, it is possible for anyone to author a policy statement
about an arbitrary set of resources, and publish it (as discussed
above in Section Section 4.1.
5.2. Updating Routing Policies from Updated IRR Resources
Ultimately, the length of time it takes to replicate resources among
IRRs is, generally, the dominant factor in reflecting changes to
resources in policy that is eventually applied within the Control
Plane of routers. The length of time to update network elements will
vary considerably depending on the size of the ISP and the number of
IRR resources that were updated during any given interval. However,
there are a variety of common techniques, that are outside the scope
of this document, that allow for this automated process to be
optimized to considerably reduce the length of time it takes to
update policies in the ISP's network.
An ISP will begin the process of updating the policy in their
network, by first fetching IRR resources associated with, for
example, a customer ASN attached to their network. Next, the ISP
constructs a new policy associated to that customer and then
evaluates if that new policy is different from existing policy
associated with that same customer. If there are no changes between
the new and existing policy associated with that customer, then the
ISP does not make any changes to the policy in their routers specific
to that customer. On the other hand, if the new policy does reflect
changes from the existing policy for that customer, then the ISP
begins a process of uploading the new policy to the routers attached
to that customer.
The process of constructing a new policy involves use of a set of
programs, e.g.: IRRtoolset, that performs recursive expansion of an
RPSL aut-num resource, that comprises an arbitrary combination of
other RPSL aut-num, as-set, route and route-set resources, according
to procedures defined by RPSL. The end result of this process is,
traditionally, a router vendor dependent configuration snippet that
defines the routing policy for that customer. This routing policy
may consist of the set of IPv4 or IPv6 prefixes, associated prefix
lengths and AS_PATH's that are supposed to be accepted from a
customer's eBGP session. However, if indicated in the appropriate
McPherson, et al. Expires January 21, 2016 [Page 11]
Internet-Draft IRR & Routing Policy Considerations July 2015
RPSL resource, the policy may also set certain BGP Attributes, such
as MED, AS_PATH prepend value, LOCAL_PREF, etc., at either the
incoming eBGP session from the customer or on static routes that are
originated by the resource holder.
An ISP's customers may not adequately plan for pre-planned
maintenance or, more likely, need to rapidly begin announcing a new
IP prefix as a result of, for example, an emergency turn-up of the
ISP customer's new downstream customer. Unfortunately, the routine,
automated process employed by the ISP means that they may not begin
updating their routing policy on their network for up to 24 hours,
because the ISP or the IRRs the ISP uses might only mirror changes to
IRR resources once every 24 hours. The time interval for the
routine/automated process is not responsive to the needs of directly
paying customer(s) who need rapid changes in their policy in rare
situations. In these situations, when a customer has an urgent need
for updates to take effect immediately, they will call the Network
Operations Center (NOC) of their ISP and request that the ISP
immediately fetch new IRR objects and push those changes out to their
network. This is often accomplished in as little as five minutes
from the time a customer contacts their ISP's NOC to the time a new
filtering policy is pushed out to the PE routers that are attached to
that customer's Attachment Circuits (AC's). It is conceivable that
some ISPs automate this using out-of-band mechanisms as well,
although the authors are unaware of any existing mechanisms that
support this.
Ultimately, the aforementioned latency with respect to "emergency
changes" in IRR resources that need to be reflected in near-real-time
in the network is compounded if the IRR resources were being used by
third party ISPs to perform filtering on their peering circuits,
where typically no such policies are employed today for this very
reason. It is likely that the length of time that it takes IRRs to
mirror changes will have to be dramatically reduced. There will need
to be a corresponding reduction in the time needed by ISPs to
evaluate whether those changes need to be re-compiled and reflected
in router policies, which would then get pushed out to ASBR's and
connected to peering circuits on their network.
6. Historical BGP Protocol Limitations
As mentioned previously, after a resource holder made changes to
their resources in an IRR, those changes would automatically be
distributed to other IRRs, ISPs would then learn of those changes,
generate a new BGP policies, and then apply those to the appropriate
subset of routers in their ASes. However, in the past, one
additional step is necessary in order to have any of those new BGP
McPherson, et al. Expires January 21, 2016 [Page 12]
Internet-Draft IRR & Routing Policy Considerations July 2015
policies take effect in the Control Plane and to allow/deny the
updated resource from a customer to their ISP and from their
immediately upstream ISP to the ISP's peers. It was necessary (often
manually) to actually induce BGP on each router to apply the new
policy within the Control Plane, thus learning of a newly announced/
changed IP prefix (or, dropping a deleted IP prefix). Unfortunately,
most of these methods were not only highly operationally impactful,
but also affected traffic forwarding to IP destinations that were
unrelated to the most recent changes to the BGP policy.
Historically, a customer would have to (re-)announce the new IP
prefix toward their ISP, but only after the ISP had placed the new
BGP policies into affect. Alternatively, the ISP would have to reset
the entire PE-CE eBGP session either by: a) bouncing the entire
interface toward the customer, (e.g.: shutdown/no shutdown); or, b)
clearing the eBGP session toward the customer, (e.g.: clear ip bgp
neighbor >IP address of CE router<). The latter two cases were, of
course, the most highly impactful and thus could generally only be
performed off-hours during a maintenance window.
Once the new IP prefix has been successfully announced by the
customer and permitted by the newly updated policy at the ISP's PE's
(attached to that customer), it would be propagated to that ISP's
ASBR's, attached to peers, at the perimeter of the ISP network.
Unfortunately, if those peers had either not yet learned of the
changes to resources in the IRR or pushed out new BGP policies (and,
reset their BGP sessions immediately afterward) incorporating those
changes, then the newly announced route would also get dropped at the
ingress ASBR's of the peers.
Ultimately, either of the two scenarios above further lengthen the
effective time it would take for changes in IRR resources to take
effect within BGP in the network. Fortunately, BGP has been enhanced
over the last several years in order that changes within BGP policy
will take affect without requiring a service impacting reset of BGP
sessions. Specifically, BGP soft-reconfiguration ([RFC2918] Section
1) and, later, Route Refresh Capability for BGP-4 [RFC2918] were
developed so that ISPs, or their customers, could induce BGP to apply
a new policy while leaving both the existing eBGP session active as
well as (unaffected) routes active in both the Loc-RIB and, more
importantly, FIB of the router. Thus, using either of these
mechanisms, an ISP or its peers currently will deploy a newly
generated BGP policy, based on changes to resources within the IRR,
and immediately trigger a non-service impacting notification to the
BGP process to have those changes take effect in their Control Plane,
either allowing a new IP prefix to be announced or an old IP prefix
to be dropped. This dramatically reduces the length of time after
changes are propagated throughout the IRRs to when those changes are
McPherson, et al. Expires January 21, 2016 [Page 13]
Internet-Draft IRR & Routing Policy Considerations July 2015
actually operational within BGP policy in an ISP's network.
7. Historical Limitations of Routers
7.1. Incremental Updates to Policy on Routers
Routers in the mid 1990's rarely supported incrementally updatable
prefix filters for BGP, and therefore, if new information was
received from a policy or internal configuration database that would
impact a policy applied to a given eBGP peer, the entire prefix list
or access list would need to be deleted and rewritten, compiled, and
installed. This was very tedious and commonly led to leaked routes
during the time when the policy was being rewritten, compiled, and
applied on a router. Furthermore, application of a new policy would
not automatically result in new ingress or egress reachability
advertisements, from that new policy, because routers at the time
would require a reset of the eBGP sessions for routing information to
be evaluated by the new policy. Of course, resetting of an eBGP
session had implications on traffic forwarding during the time the
eBGP session was reestablished and new routing information was
learned.
Routers now support the ability to perform incremental, and in situ,
updates to filter lists consisting of IP prefixes and/or AS_PATH's
that are used within an ingress or egress BGP policy. In addition,
routers also can apply those incremental updates to policy, with no
traffic disruption, using BGP soft-reconfiguration or BGP Route
Refresh, as discussed in the previous section.
7.2. Storage Requirements for Policy on Routers
Historically, routers had very limited storage capacity and would
have difficulty in storing an extremely large BGP policy on-board.
This was typically the result of router hardware vendors using an
extremely limited amount of NVRAM for storage of router
configurations.
Another challenge with historical router hardware was that writing to
NVRAM was extremely slow. For example, when the router configuration
had changed as a result of updating a BGP policy that needed to
accommodate changes in IRR resources, this would result in extremely
long times to write out these configuration changes. Sometimes, due
to bugs, this would result in loss of protocol keep-alives. This
would cause an impact to routing or forwarding of packets through the
platform.
The above limitations have largely been resolved with more modern
McPherson, et al. Expires January 21, 2016 [Page 14]
Internet-Draft IRR & Routing Policy Considerations July 2015
equipment from the last few years shipping with increasing amounts of
non-volatile storage such as: PCMCIA or USB Flash Cards, Hard Disk
Drives or Solid State Disk Drives.
However, as capacities and technologies have evolved on modern
routing hardware, so have some of the scaling requirements of the
data. In some large networks, configuration growth has begun to
"pose challenges" [IEPG89_NTT]. While the enhancements of hardware
have overcome some historical limitations, evidence suggests that
further optimizations in configuration processing may be needed in
some cases. Some of the more recent operational issues include
scheduler slips and protracted commit times. This suggests that even
though many historical hurdles have been overcome, there are still
motivations to optimize and modernize IRR technologies.
7.3. Updating Configuration on Routers
Historically, there has not been a standardized network configuration
modeling language or an associated method to update router
configurations. When an ISP detected a change in resources within
the IRR, it would fashion a router vendor dependent BGP policy and
upload that to the router usually via the following method.
First, an updated BGP policy configuration 'snippet' is generated via
processes running on an out-of-band server. Next, the operator uses
either telnet or SSH [RFC4253] to login to the CLI of a target router
and issue router vendor dependent CLI commands that will trigger the
target router to fetch the new configuration snippet via TFTP, FTP or
Secure Copy (SCP) stored on the out-of-band server. The target
router will then perform syntax checking on that configuration
snippet and, if that passes, merge that configuration snippet into
the running configuration of the router's Control Software. At this
point, the new BGP policy configuration 'snippet' is active within
the Control Plane of the router. One last step remains, which is the
operator will issue a CLI command to induce the router to perform a
"soft reset", via BGP soft-reconfiguration or BGP Route Refresh, of
the associated BGP session in order to trigger the router to apply
the new policy to routes learned from that BGP session without
disrupting traffic forwarding.
More recently, operators have the ability to use NETCONF [RFC6241] /
SSH (or, TLS) from an out-of-band server to push a BGP configuration
'snippet' from an out-of-band server toward a target router that has
that capability. However, this activity is still dependent on
generating, via the out-of-band server, a router vendor dependent XML
configuration snippet that would get uploaded via SSH or TLS to the
target router.
McPherson, et al. Expires January 21, 2016 [Page 15]
Internet-Draft IRR & Routing Policy Considerations July 2015
In the future, the ability to upload new Route Origin Authorization
(ROA) information may be provided from the RPKI to routers via the
RPKI-RTR [RFC6810] protocol. However, this will not allow operators
the ability to upload other configuration information such as BGP
policy information, such as AS_PATH's, BGP communities, etc. that
might be associated with that ROA information, like they can from IRR
generated BGP policies.
8. Summary
As discussed above, many of the problems that have traditionally
stifled IRR deployment have, themselves, become historical. However,
there are still real operational considerations that limit IRR usage
from realizing its full effectiveness. The potential for IRRs to
express inter-domain routing policy, and to allow relying parties to
learn policy, has always positioned it as a strong candidate to aid
the security postures of operators. However, while routing density
and complexity have grown, so have some of the challenges facing IRRs
(even today). Because of this state increase, the potential to model
all policies for all ASes in all routers may still remain illusive.
In addition, without an operationally deployed resource certification
framework that can tie policies to resource holders, there is a
fundamental limitation that still exists.
9. Security Considerations
One of the central concerns with IRRs is the ability of an IRR
operator to remotely influence the routing operations of an external
consumer. Specifically, if the processing of IRR contents can become
burdensome, or if the policy statements can be crafted to introduce
routing problems or anomalies, then operators may want to be
circumspect about ingesting contents from external parties. A
resource certification framework should be used to address the
authorization of IRR statements to make attestations and to
assertions (as mentioned in Section 4.1, and discussed above in
Section Section 5.1).
Additionally, the external and systemic dependencies introduced by
IRRs and other such systems employed to inform routing policy, and
how tightly or loosely coupled those systems are to the global
routing system and operational networks, introduces additional
vectors that operators and system architects should consider when
evaluating attack surface and service dependencies associated with
those elements. These attributes and concerns are certainly not
unique to IRRs, and operators should evaluate the implications of
external systems and varying degrees of coupling and operational
McPherson, et al. Expires January 21, 2016 [Page 16]
Internet-Draft IRR & Routing Policy Considerations July 2015
buffers that might be installed in their environments.
10. IANA Considerations
There are no IANA considerations.
11. Acknowledgements
The editors would like to acknowledge and thank Chris Morrow, Jeff
Haas, Wes George, and John Curran for their help and constructive
feedback.
12. Informative References
[IEPG89_NTT]
"NTT BGP Configuration Size and Scope", IEPG 89 http://
iepg.org/2014-03-02-ietf89/ietf89_iepg_jmauch.pdf.
[IRR_LIST]
Merit Network, Inc., "List of Routing Registries", List of
Routing Registries http://www.irr.net/docs/list.html.
[MERIT-IRRD]
Merit, "IRRd - Internet Routing Registry Daemon",
http://www.irrd.net.
[RC_HotNetsX]
Osterweil, E., Amante, S., McPherson, D., and D. Massey,
"The Great IPv4 Land Grab: Resource Certification for the
IPv4 Grey Market",
HotNets-X http://dl.acm.org/citation.cfm?id=2070574.
[RFC0959] Postel, J. and J. Reynolds, "File Transfer Protocol",
STD 9, RFC 959, DOI 10.17487/RFC0959, October 1985,
<http://www.rfc-editor.org/info/rfc959>.
[RFC1787] Rekhter, Y., "Routing in a Multi-provider Internet",
RFC 1787, DOI 10.17487/RFC1787, April 1995,
<http://www.rfc-editor.org/info/rfc1787>.
[RFC2622] Alaettinoglu, C., Villamizar, C., Gerich, E., Kessens, D.,
Meyer, D., Bates, T., Karrenberg, D., and M. Terpstra,
"Routing Policy Specification Language (RPSL)", RFC 2622,
DOI 10.17487/RFC2622, June 1999,
<http://www.rfc-editor.org/info/rfc2622>.
McPherson, et al. Expires January 21, 2016 [Page 17]
Internet-Draft IRR & Routing Policy Considerations July 2015
[RFC2725] Villamizar, C., Alaettinoglu, C., Meyer, D., and S.
Murphy, "Routing Policy System Security", RFC 2725,
DOI 10.17487/RFC2725, December 1999,
<http://www.rfc-editor.org/info/rfc2725>.
[RFC2769] Villamizar, C., Alaettinoglu, C., Govindan, R., and D.
Meyer, "Routing Policy System Replication", RFC 2769,
DOI 10.17487/RFC2769, February 2000,
<http://www.rfc-editor.org/info/rfc2769>.
[RFC2918] Chen, E., "Route Refresh Capability for BGP-4", RFC 2918,
DOI 10.17487/RFC2918, September 2000,
<http://www.rfc-editor.org/info/rfc2918>.
[RFC4253] Ylonen, T. and C. Lonvick, Ed., "The Secure Shell (SSH)
Transport Layer Protocol", RFC 4253, DOI 10.17487/RFC4253,
January 2006, <http://www.rfc-editor.org/info/rfc4253>.
[RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security
(TLS) Protocol Version 1.2", RFC 5246, DOI 10.17487/
RFC5246, August 2008,
<http://www.rfc-editor.org/info/rfc5246>.
[RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
<http://www.rfc-editor.org/info/rfc6241>.
[RFC6480] Lepinski, M. and S. Kent, "An Infrastructure to Support
Secure Internet Routing", RFC 6480, DOI 10.17487/RFC6480,
February 2012, <http://www.rfc-editor.org/info/rfc6480>.
[RFC6810] Bush, R. and R. Austein, "The Resource Public Key
Infrastructure (RPKI) to Router Protocol", RFC 6810,
DOI 10.17487/RFC6810, January 2013,
<http://www.rfc-editor.org/info/rfc6810>.
[RIPE2007-01]
RIPE NCC, "DRAFT: Autonomous System (AS) Number Assignment
Policies and Procedures", Foundation
Policy http://www.ripe.net/ripe/docs/ripe-452.
[RPKI_SIZING]
Osterweil, E., Manderson, T., White, R., and D. McPherson,
"Sizing Estimates for a Fully Deployed RPKI", Verisign
Labs Technical Report 1120005 version 2 http://
techreports.verisignlabs.com/
tr-lookup.cgi?trid=1120005&rev=2.
McPherson, et al. Expires January 21, 2016 [Page 18]
Internet-Draft IRR & Routing Policy Considerations July 2015
[TASRS] Osterweil, E., Amante, S., and D. McPherson, "TASRS:
Towards a Secure Routing System Through Internet Number
Resource Certification", Verisign Labs Technical Report
1130009 http://techreports.verisignlabs.com /tr-
lookup.cgi?trid=1130009&rev=1.
Authors' Addresses
Danny McPherson
Verisign, Inc.
Email: dmcpherson@verisign.com
Shane Amante
Apple, Inc.
Eric Osterweil
Verisign, Inc.
Email: eosterweil@verisign.com
Larry J. Blunk
Merit Network, Inc.
Email: ljb@merit.edu
Dave Mitchell
Singularity Networks
McPherson, et al. Expires January 21, 2016 [Page 19]
