Internet DRAFT - draft-ietf-ippm-stamp-srpm
draft-ietf-ippm-stamp-srpm
IPPM Working Group R. Gandhi, Ed.
Internet-Draft C. Filsfils
Intended status: Standards Track Cisco Systems, Inc.
Expires: 5 February 2024 M. Chen
Huawei
B. Janssens
Colt
R. Foote
Nokia
4 August 2023
Simple TWAMP (STAMP) Extensions for Segment Routing Networks
draft-ietf-ippm-stamp-srpm-18
Abstract
Segment Routing (SR) leverages the source routing paradigm. SR is
applicable to both Multiprotocol Label Switching (SR-MPLS) and IPv6
(SRv6) forwarding planes. This document specifies RFC 8762 (Simple
Two-Way Active Measurement Protocol (STAMP)) extensions for SR
networks, for both SR-MPLS and SRv6 forwarding planes by augmenting
the optional extensions defined in RFC 8972.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 5 February 2024.
Copyright Notice
Copyright (c) 2023 IETF Trust and the persons identified as the
document authors. All rights reserved.
Gandhi, et al. Expires 5 February 2024 [Page 1]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Conventions Used in This Document . . . . . . . . . . . . . . 3
2.1. Requirements Language . . . . . . . . . . . . . . . . . . 3
2.2. Abbreviations . . . . . . . . . . . . . . . . . . . . . . 3
2.3. Reference Topology . . . . . . . . . . . . . . . . . . . 3
3. Destination Node Address TLV . . . . . . . . . . . . . . . . 4
4. Return Path TLV . . . . . . . . . . . . . . . . . . . . . . . 6
4.1. Return Path Sub-TLVs . . . . . . . . . . . . . . . . . . 7
4.1.1. Return Path Control Code Sub-TLV . . . . . . . . . . 8
4.1.2. Return Address Sub-TLV . . . . . . . . . . . . . . . 9
4.1.3. Return Segment List Sub-TLVs . . . . . . . . . . . . 10
5. Interoperability with TWAMP Light . . . . . . . . . . . . . . 12
6. Security Considerations . . . . . . . . . . . . . . . . . . . 13
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 13
8. References . . . . . . . . . . . . . . . . . . . . . . . . . 16
8.1. Normative References . . . . . . . . . . . . . . . . . . 16
8.2. Informative References . . . . . . . . . . . . . . . . . 16
Appendix A. Destination Node Address TLV Use-case Example . . . 17
Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 18
Contributors . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 18
1. Introduction
Segment Routing (SR) leverages the source routing paradigm for
Software Defined Networks (SDNs). SR is applicable to both
Multiprotocol Label Switching (SR-MPLS) and IPv6 (SRv6) forwarding
planes [RFC8402]. SR Policies as defined in [RFC9256] are used to
steer traffic through a specific, user-defined paths using a stack of
Segments. A comprehensive SR Performance Measurement (PM) toolset is
one of the essential requirements to measure network performance to
provide Service Level Agreements (SLAs).
The Simple Two-Way Active Measurement Protocol (STAMP) provides
capabilities for the measurement of various performance metrics in IP
networks [RFC8762] without the use of a control channel to pre-signal
session parameters. [RFC8972] defines optional extensions, in the
Gandhi, et al. Expires 5 February 2024 [Page 2]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
form of TLVs, for STAMP. Note that the YANG data model defined in
[I-D.ietf-ippm-stamp-yang] can be used to provision the STAMP
Session-Sender and STAMP Session-Reflector.
The STAMP test packets are transmitted along an IP path between a
Session-Sender and a Session-Reflector to measure performance delay
and packet loss along that IP path. It may be desired in SR networks
that the same path (same set of links and nodes) between the Session-
Sender and Session-Reflector is used for the STAMP test packets in
both directions. This is achieved by using the STAMP [RFC8762]
extensions for SR-MPLS and SRv6 networks specified in this document
by augmenting the optional extensions defined in [RFC8972].
2. Conventions Used in This Document
2.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
2.2. Abbreviations
MPLS: Multiprotocol Label Switching.
SID: Segment Identifier.
SR: Segment Routing.
SR-MPLS: Segment Routing with MPLS forwarding plane.
SRv6: Segment Routing with IPv6 forwarding plane.
SSID: STAMP Session Identifier.
STAMP: Simple Two-Way Active Measurement Protocol.
2.3. Reference Topology
In the reference topology shown below, the STAMP Session-Sender S1
initiates a STAMP test packet and the STAMP Session-Reflector R1
transmits a reply STAMP test packet. The reply test packet may be
transmitted to the Session-Sender S1 on the same path (same set of
links and nodes) or a different path in the reverse direction from
the path taken towards the Session-Reflector R1. The T1 is a
transmit timestamp and T4 is a receive timestamp added by node S1 in
Gandhi, et al. Expires 5 February 2024 [Page 3]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
the STAMP test packet. The T2 is a receive timestamp and T3 is a
transmit timestamp added by node R1 in the STAMP test packet.
The nodes S1 and R1 may be connected via a link or an SR path
[RFC8402]. The link may be a physical interface, virtual link, or
Link Aggregation Group (LAG) [IEEE802.1AX], or LAG member. The SR
path may be an SR Policy [RFC9256] on node S1 (called head-end) with
destination to node R1 (called tail-end).
T1 T2
/ \
+-------+ Test Packet +-------+
| | - - - - - - - - - ->| |
| S1 |=====================| R1 |
| |<- - - - - - - - - - | |
+-------+ Reply Test Packet +-------+
\ /
T4 T3
STAMP Session-Sender STAMP Session-Reflector
Reference Topology
3. Destination Node Address TLV
The Session-Sender may need to transmit test packets to the Session-
Reflector with a destination address that is not a routable (i.e.,
suitable for use as the Source Address of the reply test packet)
address of the Session-Reflector. This can be facilitated, for
example, by encapsulating the STAMP packet by a tunneling protocol,
see Appendix A, for a worked example.
[RFC8972] defines STAMP Session-Sender and Session-Reflector test
packets that can include one or more optional TLVs. In this
document, the TLV type (value 9 for IPv4 and IPv6) is defined for the
Destination Node Address TLV for the STAMP test packet [RFC8972].
The formats of the Destination Node Address TLVs are shown in
Figure 1:
Gandhi, et al. Expires 5 February 2024 [Page 4]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|STAMP TLV Flags| Type=9 | Length=4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv4 Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|STAMP TLV Flags| Type=9 | Length=16 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| IPv6 Address |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: Destination Node Address TLV Format
TLV fields are defined as follows:
STAMP TLV Flags : The STAMP TLV Flags follow the procedures described
in [RFC8972] and this document.
Type : Type (value 9) for IPv4 Destination Node Address TLV or IPv6
Destination Node Address TLV.
Length : A two-octet field equal to the length of the Address field
in octets. The length is 4 octets for IPv4 address and 16 octets for
IPv6 address.
The Destination Node Address TLV indicates an address of the intended
Session-Reflector node of the test packet. If the received
Destination Node Address is one of the addresses of the Session-
Reflector, it SHOULD be used as the Source Address in the IP header
of the reply test packet. If the Destination Node Address TLV is
sent, the SSID MUST also be sent.
Gandhi, et al. Expires 5 February 2024 [Page 5]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
A Session-Reflector that recognizes this TLV, MUST set the U flag
[RFC8972] in the reply test packet to 1 if the Session-Reflector
determined that it is not the intended Destination as identified in
the Destination Node Address TLV. In this case, the Session-
Reflector does not use the received Destination Node Address as the
Source Address in the IP header of the reply test packet. Otherwise,
the Session-Reflector MUST set the U flag in the Destination Node
Address TLV in the reply test packet to 0.
4. Return Path TLV
For end-to-end SR paths, the Session-Reflector may need to transmit
the reply test packet on a specific return path. The Session-Sender
can request this in the test packet to the Session-Reflector using a
Return Path TLV. With this TLV carried in the Session-Sender test
packet, signaling and maintaining dynamic SR network state for the
STAMP sessions on the Session-Reflector are avoided.
There are two modes defined for the behaviors on the Session-
Reflector in Section 4 of [RFC8762]. A Stateful Session-Reflector
that requires configuration that must match all Session-Sender
parameters, including Source Address, Destination Address, Source UDP
Port, Destination UDP Port, and possibly SSID (assuming the SSID is
configurable and not auto-generated). In this case, a local policy
can be used to direct the test packet by creating additional states
for the STAMP sessions on the Session-Reflector. In the case of
promiscuous operation, the Stateless Session-Reflector will require
an indication of how to return the test packet on a specific path,
for example, for measurement in an ECMP environment.
For links, the Session-Reflector may need to transmit the reply test
packet on the same incoming link in the reverse direction. The
Session-Sender can request this in the test packet to the Session-
Reflector using a Return Path TLV.
[RFC8972] defines STAMP test packets that can include one or more
optional TLVs. In this document, the TLV Type (value 10) is defined
for the Return Path TLV that carries the return path for the Session-
Sender test packet. The format of the Return Path TLV is shown in
Figure 2:
Gandhi, et al. Expires 5 February 2024 [Page 6]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|STAMP TLV Flags| Type=10 | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Return Path Sub-TLVs |
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: Return Path TLV
TLV fields are defined as follows:
STAMP TLV Flags : The STAMP TLV Flags follow the procedures described
in [RFC8972] and this document.
Type : Type (value 10) for Return Path TLV.
Length : A two-octet field equal to the length of the Return Path
Sub-TLVs field in octets.
Return Path Sub-TLVs : As defined in Section 4.1.
A Session-Sender MUST NOT insert more than one Return Path TLV in the
STAMP test packet. A Session-Reflector that supports this TLV MUST
only process the first Return Path TLV in the test packet and ignore
other Return Path TLVs if present. A Session-Reflector that supports
this TLV MUST reply using the Return Path received in the Session-
Sender test packet, if no error was encountered while processing the
TLV.
A Session-Reflector that recognizes this TLV, MUST set the U flag
[RFC8972] in the reply test packet to 1 if the Session-Reflector
determined that it cannot use the return path in the test packet to
transmit the reply test packet. Otherwise, the Session-Reflector
MUST set the U flag in the reply test packet to 0.
4.1. Return Path Sub-TLVs
The Return Path TLV contains one or more Sub-TLVs to carry the
information for the requested return path. A Return Path Sub-TLV can
carry Return Path Control Code, Return Path IP Address or Return Path
Segment List.
The STAMP Sub-TLV Flags are set using the procedures described in
[RFC8972].
Gandhi, et al. Expires 5 February 2024 [Page 7]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
A Return Path TLV MUST NOT contain more than one Control Code Sub-TLV
or more than one Return Address Sub-TLV or more than one Segment List
Sub-TLV in Session-Sender test packet.
A Return Path TLV MUST NOT contain both Control Code Sub-TLV as well
as Return Address or Return Segment List Sub-TLV in Session-Sender
test packet.
A Return Path TLV MAY contain both Return Address as well as Return
Segment List Sub-TLV in Session-Sender test packet.
4.1.1. Return Path Control Code Sub-TLV
The format of the Return Path Control Code Sub-TLV is shown in
Figure 3.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|STAMP TLV Flags| Type=1 | Length=4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Control Code Flags |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: Control Code Sub-TLV in Return Path TLV
TLV fields are defined as follows:
* Type (value 1): Return Path Control Code. The Session-Sender can
request the Session-Reflector to transmit the reply test packet
based on the flags defined in the Control Code Flags field.
STAMP TLV Flags : The STAMP TLV Flags follow the procedures described
in [RFC8972] and this document.
Length : A two-octet field equal to the length of the Control Code
flags which is 4 octets.
Control Code Flags (32-bit): Reply Request Flag at bit 31 (least
significant bit) is defined as follows.
0x0 : No Reply Requested.
0x1 : Reply Requested on the Same Link.
All other bits are reserved and must be transmitted as 0 and ignored
by the receiver.
Gandhi, et al. Expires 5 February 2024 [Page 8]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
When Control Code flag for Reply Request is set to 0x0 in the
Session-Sender test packet, the Session-Reflector does not transmit
reply test packet to the Session-Sender and terminates the STAMP test
packet. Only the one-way measurement is applicable in this case.
Optionally, the Session-Reflector may locally stream performance
metrics via telemetry using the information from the received test
packet. All other Return Path Sub-TLVs MUST be ignored in this case.
When Control Code flag for Reply Request is set to 0x1 in the
Session-Sender test packet, the Session-Reflector transmits the reply
test packet over the same incoming link where the test packet is
received in the reverse direction towards the Session-Sender. The
link may be a physical interface, virtual link, or Link Aggregation
Group (LAG) [IEEE802.1AX], or LAG member. All other Return Path Sub-
TLVs MUST be ignored in this case. When using LAG member links,
STAMP extension for Micro-Session ID TLV defined in
[I-D.ietf-ippm-stamp-on-lag] can be used to identify the link.
4.1.2. Return Address Sub-TLV
The STAMP reply test packet may be transmitted to the Session-Sender
to the specified Return Address in the Return Address Sub-TLV instead
of transmitting to the Source Address in the Session-Sender test
packet.
The formats of the IPv4 and IPv6 Return Address Sub-TLVs are shown in
Figure 4.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|STAMP TLV Flags| Type=2 | Length=4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Return IPv4 Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|STAMP TLV Flags| Type=2 | Length=16 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Return IPv6 Address |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4: Return Address Sub-TLV in Return Path TLV
Gandhi, et al. Expires 5 February 2024 [Page 9]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
The TLV fields are defined as follows:
* Type : Type (value 2) for IPv4 Return Address or IPv6 Return
Address.
The Return Address requests that the Session-Reflector reply test
packet be sent to the specified address, rather than to the Source
Address in the Session-Sender test packet.
STAMP TLV Flags : The STAMP TLV Flags follow the procedures described
in [RFC8972] and this document.
Length : A two-octet field equal to the length of the Return Address
field in octets. The length is 4 octets for IPv4 address and 16
octets for IPv6 address.
4.1.3. Return Segment List Sub-TLVs
The format of the Segment List Sub-TLVs in the Return Path TLV is
shown in Figures 5 and 6. The Segments carried in Segment List Sub-
TLVs are described in [RFC8402]. The segment entries MUST be in
network order.
The Session-Sender MUST only insert one Segment List Return Path Sub-
TLV in the test packet and Segment List MUST contain at least one
Segment. The Session-Reflector MUST only process the first Segment
List Return Path Sub-TLV in the test packet and ignore other Segment
List Return Path Sub-TLVs if present.
TLV fields are defined as follows:
The Segment List Sub-TLV can be one of the following Types:
* Type (value 3): SR-MPLS Label Stack of the Return Path
* Type (value 4): SRv6 Segment List of the Return Path
STAMP TLV Flags : The STAMP TLV Flags follow the procedures described
in [RFC8972] and this document.
Length : A two-octet field equal to the length of the Segment List
field in octets. Length MUST NOT be 0.
4.1.3.1. Return Path SR-MPLS Segment-List Sub-TLV
Gandhi, et al. Expires 5 February 2024 [Page 10]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|STAMP TLV Flags| Type=3 | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Segment(1) | TC |S| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. .
. .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Segment(n) (bottom of stack) | TC |S| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5: SR-MPLS Segment List Sub-TLV in Return Path TLV
The SR-MPLS Label Stack contains a list of 32-bit Label Stack Entry
(LSE) that includes a 20-bit label value, 8-bit Time-To-Live (TTL)
value, 3-bit Traffic Class (TC) value and 1-bit End-Of-Stack (S)
field. Length of the Sub-TLV modulo 4 MUST be 0.
As an example, an SR-MPLS Label Stack Sub-TLV could carry only the
Binding SID Label [I-D.ietf-pce-binding-label-sid] of the Return SR-
MPLS Policy. The Binding SID Label of the Return SR-MPLS Policy is
local to the Session-Reflector. The mechanism to signal the Binding
SID Label to the Session-Sender is outside the scope of this
document.
As another example, an SR-MPLS Label Stack Sub-TLV could include the
Path Segment Identifier Label of the Return SR-MPLS Policy in the
Segment List of the SR-MPLS Policy.
4.1.3.2. Return Path SRv6 Segment-List Sub-TLV
Gandhi, et al. Expires 5 February 2024 [Page 11]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|STAMP TLV Flags| Type=4 | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Segment(1) (128-bit IPv6 address) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. .
. .
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Segment(n) (128-bit IPv6 address) (bottom of stack) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6: SRv6 Segment List Sub-TLV in Return Path TLV
The SRv6 Segment List contains a list of 128-bit IPv6 addresses
representing the SRv6 SIDs. Length of the Sub-TLV modulo 16 MUST be
0.
As an example, an SRv6 Segment List Sub-TLV could carry only the SRv6
Binding SID [I-D.ietf-pce-binding-label-sid] of the Return SRv6
Policy. The SRv6 Binding SID of the Return SRv6 Policy is local to
the Session-Reflector. The mechanism to signal the SRv6 Binding SID
to the Session-Sender is outside the scope of this document.
As another example, an SRv6 Segment List Sub-TLV could include the
SRv6 Path Segment Identifier of the Return SRv6 Policy in the Segment
List of the SRv6 Policy.
5. Interoperability with TWAMP Light
This document does not introduce any additional considerations for
interoperability with TWAMP Light than those described in Section 4.6
of [RFC8762].
As described in [RFC8762], there are two possible combinations for
such an interoperability use case:
- STAMP Session-Sender with TWAMP Light Session-Reflector
- TWAMP Light Session-Sender with STAMP Session-Reflector
Gandhi, et al. Expires 5 February 2024 [Page 12]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
If any of STAMP extensions defined in this document are used by STAMP
Session-Sender, the TWAMP Light Session-Reflector will view them as
the Packet Padding field.
6. Security Considerations
The security considerations specified in [RFC8762] and [RFC8972] also
apply to the extensions defined in this document. Specifically, the
authenticated mode and the message integrity protection using HMAC,
as defined in [RFC8762] Section 4.4, also apply to the procedure
described in this document.
STAMP uses the well-known UDP port number that could become a target
of denial of service (DoS) or could be used to aid on-path attacks.
Thus, the security considerations and measures to mitigate the risk
of the attack documented in Section 6 of [RFC8545] equally apply to
the STAMP extensions in this document.
If desired, attacks can be mitigated by performing basic validation
checks of the timestamp fields (such as T2 is later than T1 in the
Reference Topology in Section 2.3) in received reply test packets at
the Session-Sender. The minimal state associated with these
protocols also limit the extent of measurement disruption that can be
caused by a corrupt or invalid test packet to a single test cycle.
The usage of STAMP extensions defined in this document is intended
for deployment in a single network administrative domain. As such,
the Session-Sender address, Session-Reflector address, and Return
Path are provisioned by the operator for the STAMP session. It is
assumed that the operator has verified the integrity of the Return
Path and identity of the far-end Session-Reflector.
The STAMP extensions defined in this document may be used for
potential address spoofing. For example, a Session-Sender may
specify a Return Path IP Address that is different from the Session-
Sender address. The Session-Reflector MAY drop the Session-Sender
test packet when it cannot determine whether the Return Path IP
Address is local on the Session-Sender. To help Session-Reflector to
make that determination, the Return Path IP Address may also be
provisioned by the operator, for example, in an access control list.
7. IANA Considerations
IANA has created the "STAMP TLV Types" registry for [RFC8972]. IANA
has early allocated a value for the Destination Address TLV Type and
a value for the Return Path TLV Type from the IETF Review TLV range
of the same registry.
Gandhi, et al. Expires 5 February 2024 [Page 13]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
+======================+======================+===========+
| Value | Description | Reference |
+======================+======================+===========+
| 9 (Early Allocation) | Destination Node | This |
| | IPv4 or IPv6 Address | document |
+----------------------+----------------------+-----------+
| 10 (Early | Return Path | This |
| Allocation) | | document |
+----------------------+----------------------+-----------+
Table 1: STAMP TLV Types
IANA is requested to create a sub-registry for "Return Path Sub-TLV
Type". All code points in the range 1 through 175 in this registry
shall be allocated according to the "IETF Review" procedure as
specified in [RFC8126]. Code points in the range 176 through 239 in
this registry shall be allocated according to the "First Come, First
Served" procedure as specified in [RFC8126]. Remaining code points
are allocated according to Table 2:
+===========+==========================+===============+
| Value | Description | Reference |
+===========+==========================+===============+
| 0 - 175 | IETF Review | This document |
+-----------+--------------------------+---------------+
| 176 - 239 | First Come, First Served | This document |
+-----------+--------------------------+---------------+
| 240 - 251 | Experimental Use | This document |
+-----------+--------------------------+---------------+
| 252 - 255 | Private Use | This document |
+-----------+--------------------------+---------------+
Table 2: Return Path Sub-TLV Type Registry
IANA is requested to allocate the values for the following Sub-TLV
Types from this registry.
Gandhi, et al. Expires 5 February 2024 [Page 14]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
+======+========================================+===============+
| Type | Description | Reference |
+======+========================================+===============+
| 0 | Reserved | This document |
+------+----------------------------------------+---------------+
| 1 | Return Path Control Code | This document |
+------+----------------------------------------+---------------+
| 2 | Return IPv4 or IPv6 Address | This document |
+------+----------------------------------------+---------------+
| 3 | SR-MPLS Label Stack of the Return Path | This document |
+------+----------------------------------------+---------------+
| 4 | SRv6 Segment List of the Return Path | This document |
+------+----------------------------------------+---------------+
| 255 | Reserved | This document |
+------+----------------------------------------+---------------+
Table 3: Return Path Sub-TLV Types
IANA is requested to create a sub-registry for "Return Path Control
Code Flags" for the Return Path Control Code Sub-TLV. All code
points in the bit position 31 (counting from bit 31 as the least
significant bit) through 12 in this registry shall be allocated
according to the "IETF Review" procedure as specified in [RFC8126].
Code points in the bit position 11 through 8 in this registry shall
be allocated according to the "First Come, First Served" procedure as
specified in [RFC8126]. Remaining code points are allocated
according to Table 4:
+=========+==========================+===============+
| Bit | Description | Reference |
+=========+==========================+===============+
| 31 - 12 | IETF Review | This document |
+---------+--------------------------+---------------+
| 11 - 8 | First Come, First Served | This document |
+---------+--------------------------+---------------+
| 7 - 4 | Experimental Use | This document |
+---------+--------------------------+---------------+
| 3 - 0 | Private Use | This document |
+---------+--------------------------+---------------+
Table 4: Return Path Control Code Flags Registry
IANA is requested to allocate the value for the following Return Path
Control Code Flag from this registry.
Gandhi, et al. Expires 5 February 2024 [Page 15]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
+=====+===============+===============+
| Bit | Description | Reference |
+=====+===============+===============+
| 31 | Reply Request | This document |
+-----+---------------+---------------+
Table 5: Return Path Control Code Flags
8. References
8.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8762] Mirsky, G., Jun, G., Nydell, H., and R. Foote, "Simple
Two-Way Active Measurement Protocol", RFC 8762,
DOI 10.17487/RFC8762, March 2020,
<https://www.rfc-editor.org/info/rfc8762>.
[RFC8972] Mirsky, G., Min, X., Nydell, H., Foote, R., Masputra, A.,
and E. Ruffini, "Simple Two-Way Active Measurement
Protocol Optional Extensions", RFC 8972,
DOI 10.17487/RFC8972, January 2021,
<https://www.rfc-editor.org/info/rfc8972>.
8.2. Informative References
[RFC8402] Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,
Decraene, B., Litkowski, S., and R. Shakir, "Segment
Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,
July 2018, <https://www.rfc-editor.org/info/rfc8402>.
[RFC8126] Cotton, M., Leiba, B., and T. Narten, "Guidelines for
Writing an IANA Considerations Section in RFCs", BCP 26,
RFC 8126, DOI 10.17487/RFC8126, June 2017,
<https://www.rfc-editor.org/info/rfc8126>.
Gandhi, et al. Expires 5 February 2024 [Page 16]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
[RFC8545] Morton, A., Ed. and G. Mirsky, Ed., "Well-Known Port
Assignments for the One-Way Active Measurement Protocol
(OWAMP) and the Two-Way Active Measurement Protocol
(TWAMP)", RFC 8545, DOI 10.17487/RFC8545, March 2019,
<https://www.rfc-editor.org/info/rfc8545>.
[RFC9256] Filsfils, C., Talaulikar, K., Voyer, D., Bogdanov, A., and
P. Mattes, "Segment Routing Policy Architecture",
RFC 9256, DOI 10.17487/RFC9256, July 2022,
<https://www.rfc-editor.org/info/rfc9256>.
[I-D.ietf-pce-binding-label-sid]
Sivabalan, S., Filsfils, C., Tantsura, J., Previdi, S.,
and C. L. (editor), "Carrying Binding Label/Segment
Identifier in PCE-based Networks.", Work in Progress,
Internet-Draft, draft-ietf-pce-binding-label-sid-16, 27
March 2023, <https://www.ietf.org/archive/id/draft-ietf-
pce-binding-label-sid-16.txt>.
[I-D.ietf-ippm-stamp-yang]
Mirsky, G., Min, X., and W. S. Luo, "Simple Two-way Active
Measurement Protocol (STAMP) Data Model", Work in
Progress, Internet-Draft, draft-ietf-ippm-stamp-yang-11,
13 March 2023, <https://www.ietf.org/archive/id/draft-
ietf-ippm-stamp-yang-11.txt>.
[I-D.ietf-ippm-stamp-on-lag]
Li, Z., Zhou, T., Guo, J., Mirsky, G., and R. Gandhi,
"Simple Two-Way Active Measurement Protocol Extensions for
Performance Measurement on LAG", Work in Progress,
Internet-Draft, draft-ietf-ippm-stamp-on-lag-03, 2 July
2023, <https://www.ietf.org/archive/id/draft-ietf-ippm-
stamp-on-lag-03.txt>.
[IEEE802.1AX]
IEEE Std. 802.1AX, "IEEE Standard for Local and
metropolitan area networks - Link Aggregation", November
2008.
Appendix A. Destination Node Address TLV Use-case Example
The STAMP test packets can be encapsulated with an SR-MPLS Segment
List and IPv4 header containing destination IPv4 address from 127/8
range or STAMP test packets encapsulated with outer IPv6 header and
Segment Routing Header (SRH) with inner IPv6 header containing IPv6
destination IPv6 address ::1/128.
Gandhi, et al. Expires 5 February 2024 [Page 17]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
In an ECMP environment, the hashing function in forwarding may decide
the outgoing path using the source address, destination address, UDP
ports, IPv6 flow-label, etc. from the packet. Hence, for IPv4, for
example, different values of IPv4 destination address from 127/8
range may be used in the IPv4 header of the STAMP test packets to
measure different ECMP paths. For IPv6, for example, different
values of flow-label may be used in the IPv6 header of the STAMP test
packets to measure different ECMP paths.
In those cases, the STAMP test packets may reach a node that is not
the Session-Reflector for this STAMP session in an error condition,
and this un-intended node may transmit reply test packet that can
result in reporting of invalid measurement metrics. The intended
Session-Reflector address can be carried in the Destination Node
Address TLV to help detect this error.
Acknowledgments
The authors would like to thank Thierry Couture for the discussions
on the use-cases for Performance Measurement in Segment Routing. The
authors would also like to thank Greg Mirsky, Mike Koldychev, Gyan
Mishra, Tianran Zhou, Al Mortons, Reshad Rahman, Zhenqiang Li, Frank
Brockners, Henrik Nydell, and Cheng Li for providing comments and
suggestions. Thank you Joel Halpern for Gen-ART review, Martin Duke
for AD review, and Kathleen Moriarty for Security review. The
authors would like to thank Robert Wilton, Eric Vyncke, Paul Wouters,
John Scudder, Roman Danyliw, and Jim Guichard for IESG review.
Contributors
The following people have substantially contributed to this document:
Daniel Voyer
Bell Canada
Email: daniel.voyer@bell.ca
Authors' Addresses
Rakesh Gandhi (editor)
Cisco Systems, Inc.
Canada
Email: rgandhi@cisco.com
Clarence Filsfils
Cisco Systems, Inc.
Email: cfilsfil@cisco.com
Gandhi, et al. Expires 5 February 2024 [Page 18]
Internet-Draft Simple TWAMP Extensions for SR Networks August 2023
Mach(Guoyi) Chen
Huawei
Email: mach.chen@huawei.com
Bart Janssens
Colt
Email: Bart.Janssens@colt.net
Richard Foote
Nokia
Email: footer.foote@nokia.com
Gandhi, et al. Expires 5 February 2024 [Page 19]