Internet DRAFT - draft-ietf-l2vpn-vpls-mcast
draft-ietf-l2vpn-vpls-mcast
Network Working Group R. Aggarwal (Editor)
Internet Draft Juniper Networks
Category: Proposed Standard
Expiration Date: May 2014 Y. Kamite
NTT Communications
L. Fang
Cisco Systems, Inc
November 22 2013
Multicast in VPLS
draft-ietf-l2vpn-vpls-mcast-16.txt
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that other
groups may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Copyright and License Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
Raggarwa, Kamite & Fang [Page 1]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Abstract
[RFC4761] and [RFC4762] describe a solution for Virtual Private LAN
Service (VPLS) multicast that relies on the use of point-to-point or
multipoint-to-point unicast Label Switched Paths (LSPs) for carrying
multicast traffic. This solution has certain limitations for certain
VPLS multicast traffic profiles. For example, it may result in highly
non-optimal bandwidth utilization when large amount of multicast
traffic is to be transported.
This document describes solutions for overcoming a subset of the
limitations of existing VPLS multicast solution. It describes
procedures for VPLS multicast that utilize multicast trees in the
service provider (SP) network. The solution described in this
document allows sharing of one such multicast tree among multiple
VPLS instances. Furthermore, the solution described in this document
allows a single multicast tree in the SP network to carry traffic
belonging only to a specified set of one or more IP multicast streams
from one or more VPLS instances.
Raggarwa, Kamite & Fang [Page 2]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
Table of Contents
1 Specification of requirements ......................... 4
2 Contributors .......................................... 4
3 Terminology ........................................... 5
4 Introduction .......................................... 5
5 Overview .............................................. 6
5.1 Inclusive and Selective Multicast Trees ............... 7
5.2 BGP-Based VPLS Membership Auto-Discovery .............. 8
5.3 IP Multicast Group Membership Discovery ............... 9
5.4 Advertising P-Multicast Tree to VPLS/C-Multicast Binding 10
5.5 Aggregation ........................................... 11
5.6 Inter-AS VPLS Multicast ............................... 12
6 Intra-AS Inclusive P-Multicast Tree Auto-discovery/Binding 12
6.1 Originating intra-AS VPLS A-D routes .................. 13
6.2 Receiving intra-AS VPLS A-D routes .................... 14
7 Demultiplexing P-Multicast Tree Traffic ............... 15
7.1 One P-Multicast Tree - One VPLS Mapping ............... 15
7.2 One P-Multicast Tree - Many VPLS Mapping .............. 15
8 Establishing P-Multicast Trees ........................ 16
8.1 Common Procedures ..................................... 16
8.2 RSVP-TE P2MP LSPs ..................................... 17
8.2.1 P2MP TE LSP - VPLS Mapping ............................ 17
8.3 Receiver Initiated P2MP LSP ........................... 18
8.3.1 P2MP LSP - VPLS Mapping ............................... 18
8.4 Encapsulation of Aggregate P-Multicast Trees .......... 19
9 Inter-AS Inclusive P-Multicast Tree A-D/Binding ....... 19
9.1 VSIs on the ASBRs ..................................... 19
9.1.1 Option (a): VSIs on the ASBRs ......................... 20
9.1.2 Option (e): VSIs on the ASBRs ......................... 20
9.2 Option (b) - Segmented Inter-AS Trees ................. 20
9.2.1 Segmented Inter-AS Trees VPLS Inter-AS A-D/Binding .... 21
9.2.2 Propagating BGP VPLS A-D routes to other ASes: Overview 22
9.2.2.1 Propagating Intra-AS VPLS A-D routes in EBGP .......... 23
9.2.2.2 Inter-AS A-D route received via EBGP .................. 24
9.2.2.3 Leaf A-D Route received via EBGP ...................... 26
9.2.2.4 Inter-AS A-D Route received via IBGP .................. 26
9.3 Option (c): Non-Segmented Tunnels ..................... 27
10 Optimizing Multicast Distribution via Selective Trees . 28
10.1 Protocol for Switching to Selective Trees ............. 29
10.2 Advertising (C-S, C-G) Binding to a Selective Tree .... 31
10.3 Receiving S-PMSI A-D routes by PEs .................... 33
Raggarwa, Kamite & Fang [Page 3]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
10.4 Inter-AS Selective Tree ............................... 35
10.4.1 VSIs on the ASBRs ..................................... 35
10.4.1.1 VPLS Inter-AS Selective Tree A-D Binding .............. 36
10.4.2 Inter-AS Segmented Selective Trees .................... 36
10.4.2.1 Handling S-PMSI A-D routes by ASBRs ................... 36
10.4.2.1.1 Merging Selective Tree into an Inclusive Tree ......... 37
10.4.3 Inter-AS Non-Segmented Selective trees ................ 38
11 BGP Extensions ........................................ 39
11.1 Inclusive Tree/Selective Tree Identifier .............. 39
11.2 MCAST-VPLS NLRI ....................................... 39
11.2.1 S-PMSI A-D route ...................................... 40
11.2.2 Leaf A-D route ........................................ 41
12 Aggregation Considerations ............................ 42
13 Data Forwarding ....................................... 43
13.1 MPLS Tree Encapsulation ............................... 43
13.1.1 Mapping multiple VPLS instances to a P2MP LSP ......... 43
13.1.2 Mapping one VPLS instance to a P2MP LSP ............... 44
14 VPLS Data Packet Treatment ............................ 45
15 Security Considerations ............................... 46
16 IANA Considerations ................................... 47
17 Acknowledgments ....................................... 48
18 Normative References .................................. 48
19 Informative References ................................ 49
20 Author's Address ...................................... 50
1. Specification of requirements
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
2. Contributors
Yakov Rekhter
Juniper Networks
Chaitanya Kodeboniya
Raggarwa, Kamite & Fang [Page 4]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
3. Terminology
This document uses terminology described in [RFC4761] and [RFC4762].
In this document we refer to various auto-discovery routes, as "A-D
routes".
This document uses the prefix 'C' to refer to the customer control or
data packets and 'P' to refer to the provider control or data
packets. An IP (multicast source, multicast group) tuple is
abbreviated to (S, G).
An "Inclusive tree" is a single multicast distribution tree in the
Service Provider network that carries all the multicast traffic from
one VPLS instance on a given PE.
An "Aggregate Inclusive tree" is a single multicast distribution tree
in the Service Provider network that carries all the multicast
traffic from more than one VPLS instance on a given PE.
A "Selective tree" is a single multicast distribution tree in the
Service Provider network that carries multicast traffic belonging
only to a specified set of IP multicast streams, and all these
streams belong to the same VPLS instance on a given PE.
An "Aggregate Selective tree" is a single multicast distribution tree
in the Service Provider network that carries multicast traffic
belonging only to a specified set of IP multicast streams, and all
these streams belong to more than one VPLS instance on a given PE.
4. Introduction
[RFC4761] and [RFC4762] describe a solution for VPLS
multicast/broadcast that relies on the use of pseudowires transported
over unicast point-to-point (P2P) RSVP-TE or multipoint-to-point
(MP2P) LDP Label Switched Paths (LSPs) ([RFC3209], [RFC5036]). In
this document we refer to this solution as "ingress replication".
With ingress replication when an ingress PE of a given VPLS instance
receives a multicast/broadcast packet from one of the CEs that belong
to that instance, the ingress PE replicates the packet for each
egress PE that belong to that instance, and sends the packet to each
such egress PE using unicast tunnels.
The solution based on ingress replication has certain limitations for
certain VPLS multicast/broadcast traffic profiles. For example, it
may result in highly non-optimal bandwidth utilization in the MPLS
Raggarwa, Kamite & Fang [Page 5]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
network when a large amount of multicast/broadcast traffic is to be
transported (for more see [RFC5501]).
Ingress replication may be an acceptable model when the bandwidth of
the multicast/broadcast traffic is low and/or there is a small number
of replications performed on each outgoing interface for a particular
VPLS customer multicast stream. If this is not the case, it is
desirable to utilize multicast trees in the SP network to transmit
VPLS multicast and/or broadcast packets [RFC5501].
This document describes procedures for overcoming the limitations of
existing VPLS multicast solutions. It describes procedures for using
MPLS point-to-multipoint (P2MP) LSPs in the Service Provider (SP)
network to transport VPLS multicast and/or broadcast packets, where
these LSPs are signaled by either P2MP RSVP-TE [RFC4875] or mLDP
[RFC6388].
The procedures described in this document are applicable to both
[RFC4761] and [RFC4762].
5. Overview
Procedures described in this document provide mechanisms that allow a
single multicast distribution tree in the Service Provider (SP)
network to carry all the multicast traffic from one or more VPLS
sites connected to a given PE, irrespective of whether these sites
belong to the same or different VPLS instances. We refer to such a
tree as an "Inclusive tree" if it carries multicast traffic from one
VPLS instance on a given PE. We refer to such a tree as an "Aggregate
Inclusive tree" if it carries multicast traffic from more than one
VPLS instance on a given PE. See section "Inclusive and Selective
Multicast Trees" for further discussion on Inclusive trees.
To further improve bandwidth utilization for IP multicast streams,
this document also provides procedures by which a single multicast
distribution tree in the SP network can be used to carry traffic
belonging only to a specified set of IP multicast streams, originated
in one or more VPLS sites connected to a given PE, irrespective of
whether these sites belong to the same or different VPLS instances.
We refer to such a tree as a "Selective tree" if it carries the IP
multicast stream(s) that belong to the same VPLS instance on a given
PE. We refer to such a tree as as an "Aggregate Selective tree" if it
carries the IP multicast streams that belong to different VPLS
instances on a given PE. Use of Selective and/or Aggregate Selective
trees allows multicast traffic, by default, to be carried on an
Inclusive tree, while traffic from some specific IP multicast
streams, e.g., high bandwidth streams, could be carried on one of the
Raggarwa, Kamite & Fang [Page 6]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
Selective trees. See section "Inclusive and Selective Multicast
Trees" for further discussion on Selective trees.
Note that this document covers the use of Selective trees only for
carrying IP multicast streams. Any other use of such trees is outside
the scope of this document.
Unicast packets destined to unknown MAC addresses (i.e., not learned
yet at the ingress PE) in a given VPLS instance are flooded to remote
PEs participating in the same VPLS instance. This flooding MAY still
use ingress replication (as specified in [RFC4761], [RFC4762]), or
MAY use the procedures defined in this document to optimize flooding
across the SP core.
While the use of multicast trees in the SP network can be beneficial
when the bandwidth of the multicast traffic is high, or when it is
desirable to optimize the number of copies of a multicast packet
transmitted on a given link, this benefit comes at a cost of state in
the SP network to build multicast trees and overhead to maintain this
state.
5.1. Inclusive and Selective Multicast Trees
Multicast trees used for VPLS can be of two types:
+ Inclusive trees. This option supports the use of a single
multicast distribution tree, referred to as an Inclusive P-
Multicast tree, in the SP network to carry all the multicast
traffic from a specified set of VPLS sites connected to a given
PE. There is no assumption made with respect to whether this
traffic is IP encapsulated or not. A particular P-Multicast tree
can be set up to carry the traffic originated by sites belonging
to a single VPLS instance, or to carry the traffic originated by
sites belonging to different VPLS instances. The ability to
carry the traffic of more than one VPLS instance on the same tree
is termed Aggregation. The tree needs to include every PE that is
a member of any of the VPLS instances that are using the tree.
This implies that a PE may receive multicast traffic for a
multicast stream even if it doesn't have any receivers that are
interested in receiving traffic for that stream.
An Inclusive P-Multicast tree as defined in this document is a
P2MP tree. Thus, a P2MP tree is used to carry traffic only from
VPLS sites that are connected to the PE that is the root of the
tree.
Raggarwa, Kamite & Fang [Page 7]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
+ Selective trees. A Selective P-Multicast tree is used by a PE to
send IP multicast traffic for one or more specific IP multicast
streams, received by the PE over PE-CE interfaces that belong to
the same or different VPLS instances, to a subset of the PEs that
belong to those VPLS instances. Each of the PEs in the subset
should be on the path to a receiver of one or more multicast
streams that are mapped onto the tree. The ability to use the
same tree for multicast streams that belong to different VPLS
instances is termed Aggregation. The reason for having Selective
P-Multicast trees is to provide a PE the ability to create
separate SP multicast trees for specific multicast streams, e.g.
high bandwidth multicast streams. This allows traffic for these
multicast streams to reach only those PE routers that have
receivers for these streams. This avoids flooding other PE
routers in the VPLS instance.
A SP can use both Inclusive P-Multicast trees and Selective P-
Multicast trees or either of them for a given VPLS on a PE, based on
local configuration. Inclusive P-Multicast trees can be used for both
IP and non-IP data multicast traffic, while Selective P-Multicast
trees, as previousely state, must be used only for IP multicast data
traffic. The use of Selective P-Multicast trees for non-IP multicast
traffic is outside the scope of this document.
P-Multicast trees in the SP network can be realized via a variety of
technologies. For both inclusive and selective P-Multicast trees,
these technologies include P2MP LSPs created by RSVP-TE or mLDP.
This document also describes the data plane encapsulations for
supporting these technologies. Other technologies for realizing P-
Multicast trees are outside the scope of this document.
5.2. BGP-Based VPLS Membership Auto-Discovery
In order to establish Inclusive P-Multicast trees for one or more
VPLS instances, when aggregation is performed (with either mLDP or
P2MP RSVP-TE as the tunneling technology), or when the tunneling
technology is P2MP RSVP-TE, the PE acting as a root of a P2MP LSP
must be able to discover the other PEs that have membership of these
VPLS instances. Once the root PE discovers these other PEs, it
includes them as leaves in the P-multicast tree (i.e., P2MP LSP) This
document uses the BGP-based procedures described in [RFC4761] and
[RFC6074] for discovering the VPLS membership of all PEs. For more on
aggregation see section "Aggregation Considerations". When no
aggregation is performed and the tunneling technology is mLDP, then
the root of the P2MP LSP need not discover the other PEs that are the
leaves of that LSP.
Raggarwa, Kamite & Fang [Page 8]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
The leaves of the Inclusive P-Multicast tree must also be able to
auto-discover the identifier of the tree (note that this applies when
the tree is established by either mLDP or P2MP RSVP-TE). Procedures
to accomplish this are described in section "Advertising P-Multicast
Tree to VPLS/C-Multicast Binding".
5.3. IP Multicast Group Membership Discovery
The setup of a Selective P-Multicast tree for one or more IP
multicast (C-S, C-G)s, requires the ingress PE to learn the PEs that
have receivers in one or more of these (C-S, C-G)s, in the following
cases:
+ When aggregation is used (with either mLDP or P2MP RSVP-TE as the
tunneling technology), OR
+ When the tunneling technology is P2MP RSVP-TE
+ If ingress replication is used and the ingress PE wants to send
traffic for (C-S, C-G)s to only those PEs that are on the path to
receivers for the (C-S,C-G)s.
For more on aggregation see section "Aggregation Considerations".
For discovering the IP multicast group membership, this document
describes procedures that allow an ingress PE to enable explicit
tracking of IP multicast membership. Thus, an ingress PE can request
the IP multicast membership from egress PEs for one or more C-
multicast streams. These procedures are described in section
"Optimizing Multicast Distribution via Selective Trees".
These procedures are applicable when IGMP ([RFC2236], [RFC3376]) or
MLD ([RFC2710], [RFC3810]) is used as the multicast signaling
protocol between the VPLS CEs. They are also applicable when PIM
([RFC4601]) in either the ASM (Any-Source Multicast) or the SSM
(Source-Specific Multicast) service model is used as the multicast
routing protocol between the VPLS CEs, and PIM join suppression is
disabled on all the CEs.
However these procedures do not apply when PIM is used as the
multicast routing protocol between the VPLS CEs and PIM join
suppression is not disabled on all the CEs. This is because when PIM
join suppression is not disabled on all the CEs, PEs connected to
these CEs can not rely on PIM to determine IP multicast membership of
the receivers behind these CEs. Procedures for this case are outside
Raggarwa, Kamite & Fang [Page 9]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
the scope of this document.
The leaves of the Selective P-Multicast trees must also be able to
discover the identifier of these trees. Procedures to accomplish this
are described in section "Advertising P-Multicast Tree to VPLS/C-
Multicast Binding".
5.4. Advertising P-Multicast Tree to VPLS/C-Multicast Binding
This document describes procedures based on BGP VPLS Auto-Discovery
(A-D) routes ([RFC4761],[RFC6074]) that are used by the root of an
Aggregate P-Multicast tree to advertise the Inclusive or Selective P-
Multicast tree binding and the de-multiplexing information to the
leaves of the tree. This document uses the Provider Multicast Service
Interface (PMSI) Tunnel attribute defined [RFC6514] for this purpose.
Once an ingress PE decides to bind a set of VPLS instances or
customer multicast groups to an Inclusive P-Multicast tree or a
Selective P-Multicast tree, the PE needs to announce this binding to
other PEs in the network. This procedure is referred to as Inclusive
P-Multicast tree or Selective P-Multicast tree binding distribution
and is performed using BGP. The decision to bind a set of VPLS
instances or customer multicast group is a local matter to the
ingress, and is controlled via provisioning/configuration on that PE.
When an Aggregated Inclusive P-Multicast tree is used by an ingress
PE, this binding distribution implies that (a) an ingress PE MUST
announce the binding of all VPLS instances bound to the Inclusive P-
Multicast tree, and (b) other PEs that have these instances receive
these announcements. The inner label assigned by the ingress PE for
each VPLS MUST be included if more than one VPLS is bound to the same
P-Multicast tree. The Inclusive P-Multicast tree Identifier MUST be
included.
For a Selective P-Multicast tree this binding distribution implies
announcing all the specific <C-S, C-G> entries bound to this P-
Multicast tree along with the Selective P-Multicast tree Identifier.
The inner label assigned for each <C-S, C-G> MUST be included if <C-
S, C-G>s from different VPLS instances are bound to the same P-
Multicast tree. The labels MUST be distinct on a per VPLS basis and
MAY be distinct on a per <C-S, C-G> basis. The Selective P-Multicast
tree Identifier MUST be included.
Raggarwa, Kamite & Fang [Page 10]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
5.5. Aggregation
As described earlier in this document, the ability to carry the
traffic of more than one VPLS on the same P-Multicast tree is termed
aggregation.
Aggregation enables the SP to place a bound on the amount of
multicast tree forwarding and control plane state which the P routers
must have. Let us call the number of VPLS instances aggregated onto a
single P-Multicast tree as the "Aggregation Factor". When Inclusive
source P-Multicast trees are used the number of trees that a PE is
the root of is proportional to Number of VPLS instances on the PE
divided by the Aggregation Factor.
In this case the state maintained by a P router, is proportional to:
AveVPLS NPE
------- X --------
Aggr AvePTree
Where:
AveVPLS is the average number of VPLS instances on a PE
Aggr is the aggregation factor
NPE is the number of PEs
AvePTree is the average number of P-multicast that transit
a given P-router
Thus, the state does not grow linearly with the number of VPLS
instances.
Aggregation requires a mechanism for the egresses of the P-Multicast
tree to demultiplex the multicast traffic received over the P-
Multicast tree. To enable the egress nodes to perform this
demultiplexing, upstream-assigned labels [RFC5331] MUST be assigned
and distributed by the root of the aggregate P-multicast tree.
Aggregation procedures would require two MPLS labels in the label
stack. This does not introduce any new implications on MTU, as even
VPLS multicast supported by ingress replication requires two MPLS
labels in the label stack.
Raggarwa, Kamite & Fang [Page 11]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
5.6. Inter-AS VPLS Multicast
This document defines four models of inter-AS VPLS service, referred
here as option (a), (b), (c), and (e). Options (a), (b), and (c)
defined in this document are very similar to the three methods,
method (a), method (b), and method (c), described in section "Multi-
AS VPLS" [RFC4761], which in turn extends the concepts of [RFC4364]
to inter-AS VPLS.
For option (a) and option (b) support, this document specifies a
model where Inter-AS VPLS service can be offered without requiring a
single P-Multicast tree to span multiple ASes. There are two variants
of this model and they are described in section "Inter-AS Inclusive
P-Multicast Tree A-D/Binding".
For option (c) support this document specifies a model where Inter-AS
VPLS service is offered by requiring a single P-Multicast tree to
span multiple ASes. This is because in the case of option (c) the
ASBRs do not exchange BGP-VPLS NLRIs or A-D routes.
In addition to options (a), (b), and (c), this document also
specifies option (e), which one may think of as a variant of option
(a).
For more on these inter-AS options see section "Inter-AS Inclusive P-
Multicast Tree A-D/Binding".
6. Intra-AS Inclusive P-Multicast Tree Auto-discovery/Binding
This section specifies procedures for the intra-AS auto-discovery of
VPLS membership and the distribution of information used to
instantiate P-Multicast Tunnels.
VPLS auto-discovery/binding consists of two components: intra-AS and
inter-AS. The former provides VPLS auto-discovery/binding within a
single AS. The latter provides VPLS auto-discovery/binding across
multiple ASes. Inter-AS auto-discovery/binding is described in
section "Inter-AS Inclusive P-Multicast Tree A-D/Binding".
VPLS auto-discovery using BGP as described in [RFC4761, RFC6074]
enables a PE to learn the VPLS instance membership of other PEs. A PE
that belongs to a particular VPLS instance announces a BGP Network
Layer Reachability Information (NLRI) that identifies the Virtual
Switch Instance (VSI). This NLRI is constructed from the <Route-
Distinguisher (RD), VPLS Edge Device Identifier (VE-ID)> tuple. The
NLRI defined in [RFC4761] comprises the <RD, VE-ID> tuple and label
blocks for pseudo-wire (PW) signaling. The VE-ID in this case is a
Raggarwa, Kamite & Fang [Page 12]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
two octet number. The NLRI defined in [RFC6074] comprises only the
<RD, VE-ID> where the VE-ID is a four octet number.
The procedures for constructing Inclusive intra-AS and inter-AS trees
as specified in this document require the BGP A-D NLRI to carry only
the <RD, VE-ID>. Hence these procedures can be used for both BGP-VPLS
and LDP-VPLS with BGP A-D.
It is to be noted that BGP A-D is an inherent feature of BGP-VPLS.
However it is not an inherent feature of LDP-VPLS. In fact there are
deployments and/or implementations of LDP-VPLS that require
configuration to enable a PE in a particular VPLS to determine other
PEs in the VPLS and exchange PW labels using FEC 128 (PWid FEC)
[RFC4447]. The use of BGP A-D for LDP-VPLS [RFC6074], to enable
automatic setup of PWs, requires FEC 129 (Generalized PWid FEC)
[RFC4447]. However FEC 129 is not required in order to use procedures
in this document for LDP-VPLS. An LDP-VPLS implementation that
supports this document MUST support the BGP A-D procedures to setup
P-Multicast trees, as described here, and it MAY support FEC 129 to
automate the signaling of PWs.
6.1. Originating intra-AS VPLS A-D routes
To participate in the VPLS auto-discovery/binding a PE router that
has a given VSI of a given VPLS instance originates a BGP VPLS intra-
AS A-D route and advertises this route in Multi-Protocol (MP) IBGP.
The route is constructed as described in [RFC4761] and [RFC6074].
The route carries a single L2VPN NLRI with the RD set to the RD of
the VSI, and the VE-ID set to the VE-ID of the VSI. The route also
carries one or more Route Targets (RTs) as specified in [RFC4761] and
[RFC6074].
If an Inclusive P-Multicast tree is used to instantiate the provider
tunnel for VPLS multicast on the PE, the advertising PE MUST
advertise the type and the identity of the P-Multicast tree in the
PMSI Tunnel attribute. This attribute is described in section
"Inclusive Tree/Selective Tree Identifier".
A PE that uses an Inclusive P-Multicast tree to instantiate the
provider tunnel MAY aggregate two or more VPLS instances present on
the PE onto the same tree. If the PE decides to perform aggregation
after it has already advertised the intra-AS VPLS A-D routes for
these VPLS instances, then aggregation requires the PE to re-
advertise these routes. The re-advertised routes MUST be the same as
the original ones, except for the PMSI Tunnel attribute (the re-
advertised route will replace of the previously advertised route). If
Raggarwa, Kamite & Fang [Page 13]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
the PE has not previously advertised intra-AS A-D routes for these
VPLS instances, then the aggregation requires the PE to advertise
(new) intra-AS A-D routes for these VPLS instances. The PMSI
attribute in the newly advertised/re-advertised routes MUST carry the
identity of the P-Multicast tree that aggregates the VPLS instances,
as well as an MPLS upstream-assigned label [RFC5331]. Each re-
advertised or newly advertised route MUST have a label that is
distinct within the scope of the PE that advertises the route.
Discovery of PE capabilities in terms of what tunnels types they
support is outside the scope of this document. Within a given AS PEs
participating in a VPLS are expected to advertise tunnel bindings
whose tunnel types are supported by all other PEs that are
participating in this VPLS and are part of the same AS.
6.2. Receiving intra-AS VPLS A-D routes
When a PE receives a BGP Update message that carries an intra-AS A-D
route such that (a) the route was originated by some other PE within
the same AS as the local PE, (b) at least one of the Route Targets of
the route matches one of the import Route Targets configured for a
particular VSI on the local PE, (c) the BGP route selection
determines that this is the best route with respect to the NLRI
carried by the route, and (d) the route carries the PMSI Tunnel
attribute, the PE performs the following:
+ If the Tunnel Type in the PMSI Tunnel attribute is set to LDP
P2MP LSP, the PE SHOULD join the P-Multicast tree whose identity
is carried in the PMSI Tunnel attribute.
+ If the Tunnel Type in the PMSI Tunnel attribute is set to RSVP-TE
P2MP LSP, the receiving PE has to establish the appropriate state
to properly handle the traffic received over that LSP. The PE
that originated the route MUST establish an RSVP-TE P2MP LSP with
the local PE as a leaf. This LSP MAY have been established before
the local PE receives the route.
+ If the PMSI Tunnel attribute does not carry a label, then all
packets that are received on the P-Multicast tree, as identified
by the PMSI Tunnel attribute, are forwarded using the VSIs that
have at least one of its import Route Targets that matches one of
the Route Targets of the received A-D route.
+ If the PMSI Tunnel attribute has the Tunnel Type set to LDP P2MP
LSP or RSVP-TE P2MP LSP, and the attribute also carries an MPLS
label, then the egress PE MUST treat this as an upstream-assigned
label, and all packets that are received on the P-Multicast tree,
Raggarwa, Kamite & Fang [Page 14]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
as identified by the PMSI Tunnel attribute, with that upstream
label are forwarded using the VSIs that have at least one of its
import Route Target that matches one of the Route Targets of the
received intra-AS A-D route.
Furthermore, if the local PE uses RSVP-TE P2MP LSP for sending
(multicast) traffic, originated by VPLS sites connected to the PE, to
the sites attached to other PEs then the local PE MUST use the
Originating Router's IP address information carried in the intra-AS
A-D route to add the PE, that originated the route, as a leaf node to
the LSP. This MUST be done irrespective of whether the received
Intra-AS A-D route carries the PMSI Tunnel attribute or not.
7. Demultiplexing P-Multicast Tree Traffic
Demultiplexing received VPLS traffic requires the receiving PE to
determine the VPLS instance the packet belongs to. The egress PE can
then perform a VPLS lookup to further forward the packet. It also
requires the egress PE to determine the identity of the ingress PE
for MAC learning, as described in section "VPLS Data Packet
Treatment".
7.1. One P-Multicast Tree - One VPLS Mapping
When a P-Multicast tree is mapped to only one VPLS, determining the
tree on which the packet is received is sufficient to determine the
VPLS instance on which the packet is received. The tree is determined
based on the tree encapsulation. If MPLS encapsulation is used,
e.g.,: RSVP-TE P2MP LSPs, the outer MPLS label is used to determine
the tree. Penultimate-hop-popping MUST be disabled on the MPLS LSP
(RSVP-TE P2MP LSP or mLDP P2MP LSP).
7.2. One P-Multicast Tree - Many VPLS Mapping
As traffic belonging to multiple VPLS instances can be carried over
the same tree, there is a need to identify the VPLS the packet
belongs to. This is done by using an inner label that determines the
VPLS for which the packet is intended. The ingress PE uses this label
as the inner label while encapsulating a customer multicast data
packet. Each of the egress PEs must be able to associate this inner
label with the same VPLS and use it to demultiplex the traffic
received over the Aggregate Inclusive tree or the Aggregate Selective
tree.
Raggarwa, Kamite & Fang [Page 15]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
If traffic from multiple VPLS instances is carried on a single tree,
upstream-assigned labels [RFC5331] MUST be used. Hence the inner
label is assigned by the ingress PE. When the egress PE receives a
packet over an Aggregate tree, the outer encapsulation (in the case
of MPLS P2MP LSPs, the outer MPLS label) specifies the label space to
perform the inner label lookup. The same label space MUST be used by
the egress PE for all P-Multicast trees that have the same root
[RFC5331].
If the tree uses MPLS encapsulation, as in RSVP-TE P2MP LSPs, the
outer MPLS label and optionally the incoming interface provides the
label space of the label beneath it. This assumes that penultimate-
hop-popping is disabled. The egress PE MUST NOT advertise IMPLICIT
NULL or EXPLICIT NULL for that tree once it is known to the egress PE
that the tree is bound to one or more VPLS instances. Once the label
representing the tree is popped off the MPLS label stack, the next
label is the demultiplexing information that allows the proper VPLS
instance to be determined.
The ingress PE informs the egress PEs about the inner label as part
of the tree binding procedures described in section "BGP Extensions".
8. Establishing P-Multicast Trees
This document supports only P2MP P-Multicast trees wherein it is
possible for egress PEs to identify the ingress PE to perform MAC
learning. Specific procedures are specified only for RSVP-TE P2MP
LSPs and mLDP P2MP LSPs. An implementation that supports this
document MUST support RSVP-TE P2MP LSPs and mLDP P2MP LSPs.
8.1. Common Procedures
The following procedures apply to both RSVP-TE P2MP and mLDP P2MP
LSPs.
Demultiplexing the C-multicast data packets at the egress PE requires
that the PE must be able to determine the P2MP LSP that the packets
are received on. This enables the egress PE to determine the VPLS
instances that the packet belongs to. To achieve this the LSP MUST be
signaled with penultimate-hop-popping (PHP) off and a non special
purpose MPLS label off as described in section "Demultiplexing P-
Multicast Tree Traffic". In other words an egress PE MUST NOT
advertise IMPLICIT NULL or EXPLICIT NULL for a P2MP LSP that is
carrying traffic for one or more VPLS instances. This is because the
egress PE needs to rely on the MPLS label, that it advertises to its
Raggarwa, Kamite & Fang [Page 16]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
upstream neighbor, to determine the P2MP LSP that a C-multicast data
packet is received on.
The egress PE also needs to identify the ingress PE to perform MAC
learning. When P2MP LSPs are used as P2MP trees, determining the P2MP
LSP that the packets are received on, is sufficient to determine the
ingress PE. This is because the ingress PE is the root of the P2MP
LSP.
The egress PE relies on receiving the PMSI Tunnel attribute in BGP to
determine the VPLS instance to P2MP LSP mapping.
8.2. RSVP-TE P2MP LSPs
This section describes procedures that are specific to the usage of
RSVP-TE P2MP LSPs for instantiating a P-Multicast tree. Procedures in
[RFC4875] are used to signal the P2MP LSP. The LSP is signaled as the
root of the P2MP LSP discovers the leaves. The egress PEs are
discovered using the procedures described in section "Intra-AS
Inclusive P-Multicast Tree Auto-discovery/Binding". Aggregation as
described in this document is supported.
8.2.1. P2MP TE LSP - VPLS Mapping
P2MP TE LSP to VPLS mapping is learned at the egress PEs using BGP
based advertisements of the P2MP TE LSP - VPLS mapping. They require
that the root of the tree include the P2MP TE LSP identifier as the
tunnel identifier in the BGP advertisements. This identifier contains
the following information elements:
- The type of the tunnel is set to RSVP-TE P2MP LSP
- RSVP-TE P2MP LSP's SESSION Object
This Tunnel Identifier is described in section "Inclusive
Tree/Selective Tree Identifier".
Once the egress PE receives the P2MP TE LSP to VPLS mapping:
+ If the egress PE already has RSVP-TE state for the P2MP TE LSP,
it MUST begin to assign an MPLS label from the non special
purpose label range, for the P2MP TE LSP and signal this to the
previous hop of the P2MP TE LSP. Further it MUST create
forwarding state to forward packets received on the P2MP LSP.
Raggarwa, Kamite & Fang [Page 17]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
+ If the egress PE does not have RSVP-TE state for the P2MP TE LSP,
it MUST retain this mapping. Subsequently when the egress PE
receives the RSVP-TE P2MP signaling message, it creates the RSVP-
TE P2MP LSP state. It MUST then assign an MPLS label from the
non-reserved label range, for the P2MP TE LSP, and signal this to
the previous hop of the P2MP TE LSP.
Note that if the signaling to set up an RSVP-TE P2MP LSP is
completed before a given egress PE learns, via a PMSI Tunnel
attribute, of the VPLS or set of VPLS instances to which the LSP
is bound, the PE MUST discard any traffic received on that LSP
until the binding is received. In order for the egress PE to be
able to discard such traffic it needs to know that the LSP is
associated with one or more VPLS instances and that the VPLS A-D
route that binds the LSP to a VPLS has not yet been received.
This is provided by extending [RFC4875] with [RFC6511].
8.3. Receiver Initiated P2MP LSP
Receiver initiated P2MP LSPs can also be used. The mLDP procedures
([RFC6388]) MUST be used to signal such LSPs. The LSP is signaled
once the leaves receive the LDP FEC for the tree from the root, as
described in section "Intra-AS Inclusive P-Multicast Tree Auto-
discovery/Binding". When aggregation is used, an ingress PE is
required to discover the egress PEs (see section "Aggregation
Considerations" for the rationale), and this is achieved using the
procedures in section "Intra-AS Inclusive P-Multicast Tree Auto-
discovery/Binding".
8.3.1. P2MP LSP - VPLS Mapping
P2MP LSP to VPLS mapping is learned at the egress PEs using BGP based
advertisements of the P2MP LSP - VPLS mapping. They require that the
root of the tree include the P2MP LSP identifier as the tunnel
identifier in the BGP advertisements. This identifier contains the
following information elements:
- The type of the tunnel is set to LDP P2MP LSP
- LDP P2MP FEC which includes an identifier generated by the root.
Each egress PE SHOULD "join" the P2MP MPLS tree by sending LDP label
mapping messages for the LDP P2MP FEC, that was learned in the BGP
advertisement, using procedures described in [RFC6388].
Raggarwa, Kamite & Fang [Page 18]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
8.4. Encapsulation of Aggregate P-Multicast Trees
An Aggregate Inclusive P-Multicast tree or an Aggregate Selective P-
Multicast tree MUST use MPLS encapsulation. The protocol type in the
data link header is as described in [RFC5332].
9. Inter-AS Inclusive P-Multicast Tree A-D/Binding
As stated earlier, this document defines four models of inter-AS VPLS
service, referred here as option (a), (b), (c) and (e). This section
contains procedures to support these models.
For supporting option (a), (b) and (e) this section specifies a model
where inter-AS VPLS service can be offered without requiring a single
P-Multicast tree to span multiple ASes. This allows individual ASes
to potentially use different P-tunneling technologies. There are two
variants of this model. One that requires MAC lookup on the ASBRs,
and applies to option (a) and (e). The other is one that does not
require MAC lookup on the ASBRs, and instead builds segmented inter-
AS Inclusive or Selective trees. This applies only to option (b).
For supporting option (c) this section specifies a model where Inter-
AS VPLS service is offered by requiring a single Inclusive P-
Multicast tree to span multiple ASes. This is referred to as a non-
segmented P-Multicast tree. This is because in the case of option (c)
the ASBRs do not exchange BGP-VPLS NLRIs or VPLS A-D routes.
Selective inter-AS trees for option (c) support may be segmented or
non-segmented.
An implementation MUST support options (a), (b), and (c), and MAY
support option(e). When there are multiple ways for implementing one
of these options, this section specifies which one is mandatory.
9.1. VSIs on the ASBRs
When VSIs are configured on ASBRs, the ASBRs MUST perform a MAC
lookup, in addition to any MPLS lookups, to determine the forwarding
decision on a VPLS packet. The P-Multicast trees are confined to an
AS. An ASBR on receiving a VPLS packet from another ASBR is required
to perform a MAC lookup to determine how to forward the packet. Thus
an ASBR is required to keep a VSI for the VPLS instance and MUST be
configured with its own VE ID for the VPLS instance. The BGP VPLS A-
D routes generated by PEs in an AS MUST NOT be propagated outside the
AS.
Raggarwa, Kamite & Fang [Page 19]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
9.1.1. Option (a): VSIs on the ASBRs
In option (a) an ASBR acts as a PE for the VPLSs that span the AS of
the ASBR and an AS to which the ASBR is connected. The local ASBR
views the ASBR in the neighboring AS as a CE connected to it by a
link with separate VLAN sub-interfaces for each such VPLS. Similarly,
the ASBR in the neighboring AS acts as a PE for such VPLS from the
neighboring AS's point of view, and views the local ASBR as a CE.
The local ASBR uses a combination of the incoming link and a
particular VLAN sub-interface on that link to detemine the VSI for
the packets it receives from the ASBR in the neighboring AS.
In option (a) the ASBRs do not exchange VPLS A-D routes.
An implementation MUST support option (a).
9.1.2. Option (e): VSIs on the ASBRs
The VSIs on the ASBRs scheme can be used such that the interconnect
between the ASBRs is a PW and MPLS encapsulation is used between the
ASBRs. An ASBR in one AS determines the VSI for packets received
from an adjoining ASBR in another AS based on the incoming MPLS PW
label. This is referred to as option (e). The only VPLS A-D routes
that are propagated outside the AS are the ones originated by ASBRs.
This MPLS PW connects the VSIs on the ASBRs and MUST be signaled
using the procedures defined in [RFC4761] or [RFC4762].
The P-Multicast trees for a VPLS are confined to each AS and the VPLS
auto-discovery/binding MUST follow the intra-AS procedures described
in section "Demultiplexing Multicast Tree Traffic".
An implementation MAY support option (e).
9.2. Option (b) - Segmented Inter-AS Trees
In this model, an inter-AS P-Multicast tree, rooted at a particular
PE for a particular VPLS instance, consists of a number of
"segments", one per AS, which are stitched together at ASBRs. These
are known as "segmented inter-AS trees". Each segment of a segmented
inter-AS tree may use a different multicast transport technology. In
this model, an ASBR is not required to keep a VSI for the VPLS
instance, and is not required to perform a MAC lookup in order to
forward the VPLS packet. This implies that an ASBR is not required to
be configured with a VE ID for the VPLS.
Raggarwa, Kamite & Fang [Page 20]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
An implementation MUST support option (b) using this model.
The construction of segmented Inter-AS trees requires the BGP-VPLS A-
D NLRI described in [RFC4761, RFC6074]. A BGP VPLS A-D route for a
<RD, VE ID> tuple advertised outside the AS, to which the originating
PE belongs, will be referred to as an inter-AS VPLS A-D route (though
this route is originated by a PE as an intra-AS route, and is
referred to as an inter-AS route outside the AS).
In addition to this, segmented inter-AS trees require support for the
PMSI Tunnel attribute described in section "Inclusive Tree/Selective
Tree Identifier". They also require additional procedures in BGP to
signal leaf A-D routes between ASBRs as explained in subsequent
sections.
9.2.1. Segmented Inter-AS Trees VPLS Inter-AS A-D/Binding
This section specifies the procedures for inter-AS VPLS A-D/binding
for segmented inter-AS trees.
An ASBR must be configured to support a particular VPLS as follows:
+ An ASBR MUST be configured with a set of (import) Route Targets
(RTs) that specify the set of VPLS instances supported by the
ASBR. These Route Targets control acceptance of BGP VPLS auto-
discovery routes by the ASBR. Note that instead of being
configured, the ASBR MAY obtain this set of (import) Route
Targets (RTs) by using Route Target Constrain [RFC4684].
+ The ASBR MUST be configured with the tunnel types for the intra-
AS segments of the VPLS instances supported by the ASBR, as well
as (depending on the tunnel type) the information needed to
create the PMSI Tunnel attribute for these tunnel types. Note
that instead of being configured, the ASBR MAY derive the tunnel
types from the intra-AS A-D routes received by the ASBR from the
PEs in its own AS.
If an ASBR is configured to support a particular VPLS instance, the
ASBR MUST participate in the intra-AS VPLS auto-discovery/binding
procedures for that VPLS instance within the ASBR's own AS, as
defined in this document.
Moreover, in addition to the above the ASBR performs procedures
specified in section "Propagating BGP VPLS A-D routes to other ASes:
Overview".
Raggarwa, Kamite & Fang [Page 21]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
9.2.2. Propagating BGP VPLS A-D routes to other ASes: Overview
A BGP VPLS A-D route for a given VPLS, originated by a PE within a
given AS, is propagated via BGP to other ASes. The precise rules for
distributing and processing the inter-AS A-D routes are given in
subsequent sections.
Suppose that an ASBR A receives and installs a BGP VPLS A-D route for
VPLS "X" and VE ID "V" that originated at a particular PE, PE1, that
is in the same AS as A. The BGP next hop of that received route
becomes A's "upstream neighbor" on a multicast distribution tree for
(X, V) that is rooted at PE1. Likewise, when A re-advertises this
route to ASBRs in A's neighboring ASes, from the perspective of these
ASBRs A becomes their "upstream neighbor" on the multicast
distribution tree for (X, V) that is rooted at PE1.
When the BGP VPLS A-D routes have been distributed to all the
necessary ASes, they define a "reverse path" from any AS that
supports VPLS X and VE ID V back to PE1. For instance, if AS2
supports VPLS X, then there will be a reverse path for VPLS X and VE
ID V from AS2 to AS1. This path is a sequence of ASBRs, the first of
which is in AS2, and the last of which is in AS1. Each ASBR in the
sequence is the BGP next hop of the previous ASBR in the sequence.
This reverse path information can be used to construct a
unidirectional multicast distribution tree for VPLS X and VE ID V,
containing all the ASes that support X, and having PE1 at the root.
We call such a tree an "inter-AS tree". Multicast data originating in
VPLS sites for VPLS X connected to PE1 will travel downstream along
the tree which is rooted at PE1.
The path along an inter-AS tree is a sequence of ASBRs. It is still
necessary to specify how the multicast data gets from a given ASBR to
the set of ASBRs which are immediately downstream of the given ASBR
along the tree. This is done by creating "segments": ASBRs in
adjacent ASes will be connected by inter-AS segments, ASBRs in the
same AS will be connected by "intra-AS segments".
For a given inter-AS tree and a given AS there MUST be only one ASBR
within that AS that accepts traffic flowing on that tree. Further
for a given inter-AS tree and a given AS there MUST be only one ASBR
in that AS that sends the traffic flowing on that tree to a
particular adjacent AS. The precise rules for accomplishing this are
given in subsequent sections.
An ASBR initiates creation of an intra-AS segment when the ASBR
receives an inter-AS A-D route from an EBGP neighbor. Creation of the
segment is completed as a result of distributing, via IBGP, this
Raggarwa, Kamite & Fang [Page 22]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
route within the ASBR's own AS.
For a given inter-AS tunnel each of its intra-AS segments could be
constructed by its own independent mechanism. Moreover, by using
upstream-assigned labels within a given AS multiple intra-AS segments
of different inter-AS tunnels of either the same or different VPLS
instances may share the same P-Multicast tree.
If the P-Multicast tree instantiating a particular segment of an
inter-AS tunnel is created by a multicast control protocol that uses
receiver-initiated joins (e.g, mLDP), and this P-Multicast tree does
not aggregate multiple segments, then all the information needed to
create that segment will be present in the inter-AS A-D routes
received by the ASBR from the neighboring ASBR. But if the P-
Multicast tree instantiating the segment is created by a protocol
that does not use receiver-initiated joins (e.g., RSVP-TE, ingress
unicast replication), or if this P-Multicast tree aggregates multiple
segments (irrespective of the multicast control protocol used to
create the tree), then the ASBR needs to learn the leaves of the
segment. These leaves are learned from A-D routes received from other
PEs in the AS, for the same VPLS as the one that the segment belongs
to.
The following sections specify procedures for propagation of inter-AS
A-D routes across ASes in order to construct inter-AS segmented
trees.
9.2.2.1. Propagating Intra-AS VPLS A-D routes in EBGP
For a given VPLS configured on an ASBR when the ASBR receives intra-
AS A-D routes originated by PEs in its own AS, the ASBR MUST
propagate each of these route in EBGP. This procedure MUST be
performed for each of the VPLS instances configured on the ASBR.
Each of these routes is constructed as follows:
+ The route carries a single BGP VPLS A-D NLRI with the RD and VE
ID being the same as the NLRI in the received intra-AS A-D route.
+ The Next Hop field of the MP_REACH_NLRI attribute is set to a
routable IP address of the ASBR.
+ The route carries the PMSI Tunnel attribute with the Tunnel Type
set to Ingress Replication; the attribute carries no MPLS labels.
Raggarwa, Kamite & Fang [Page 23]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
+ The route MUST carry the export Route Target used by the VPLS.
9.2.2.2. Inter-AS A-D route received via EBGP
When an ASBR receives from one of its EBGP neighbors a BGP Update
message that carries an inter-AS A-D route, if (a) at least one of
the Route Targets carried in the message matches one of the import
Route Targets configured on the ASBR, and (b) the ASBR determines
that the received route is the best route to the destination carried
in the NLRI of the route, the ASBR re-advertises this inter-AS A-D
route to other PEs and ASBRs within its own AS. The best route
selection procedures MUST ensure that for the same destination, all
ASBRs in an AS pick the same route as the best route. The best route
selection procedures are specified in [RFC4761] and clarified in
[MULTI-HOMING]. The best route procedures ensure that if multiple
ASBRs, in an AS, receive the same inter-AS A-D route from their EBGP
neighbors, only one of these ASBRs propagates this route in IBGP.
This ASBR becomes the root of the intra-AS segment of the inter-AS
tree and ensures that this is the only ASBR that accepts traffic into
this AS from the inter-AS tree.
When re-advertising an inter-AS A-D route the ASBR MUST set the Next
Hop field of the MP_REACH_NLRI attribute to a routable IP address of
the ASBR.
Depending on the type of a P-Multicast tunnel used to instantiate the
intra-AS segment of the inter-AS tunnel, the PMSI Tunnel attribute of
the re-advertised inter-AS A-D route is constructed as follows:
+ If the ASBR uses ingress replication to instantiate the intra-AS
segment of the inter-AS tunnel, the re-advertised route MUST NOT
carry the PMSI Tunnel attribute.
+ If the ASBR uses a P-Multicast tree to instantiate the intra-AS
segment of the inter-AS tunnel, the PMSI Tunnel attribute MUST
contain the identity of the tree that is used to instantiate the
segment (note that the ASBR could create the identity of the tree
prior to the actual instantiation of the segment). If in order to
instantiate the segment the ASBR needs to know the leaves of the
tree, then the ASBR obtains this information from the A-D routes
received from other PEs/ASBRs in ASBR's own AS.
+ An ASBR that uses a P-Multicast tree to instantiate the intra-AS
segment of the inter-AS tunnel MAY aggregate two or more VPLS
instances present on the ASBR onto the same tree. If the ASBR
already advertises inter-AS A-D routes for these VPLS instances,
then aggregation requires the ASBR to re-advertise these routes.
Raggarwa, Kamite & Fang [Page 24]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
The re-advertised routes MUST be the same as the original ones,
except for the PMSI Tunnel attribute. If the ASBR has not
previously advertised inter-AS A-D routes for these VPLS
instances, then the aggregation requires the ASBR to advertise
(new) inter-AS A-D routes for these VPLS instances. The PMSI
Tunnel attribute in the newly advertised/re-advertised routes
MUST carry the identity of the P-Multicast tree that aggregates
the VPLS instances, as well as an MPLS upstream-assigned label
[RFC5331]. Each newly advertised or re-advertised route MUST have
a label that is distinct within the scope of the ASBR.
In addition the ASBR MUST send to the EBGP neighbor, from whom it
receives the inter-AS A-D route, a BGP Update message that carries a
leaf A-D route. The exact encoding of this route is described in
section "BGP Extensions". This route contains the following
information elements:
+ The route carries a single NLRI with the Route Key field set to
the <RD, VE ID> tuple of the BGP VPLS A-D NLRI of the inter-AS A-
D route received from the EBGP neighbor. The NLRI also carries
the IP address of the ASBR (this MUST be a routable IP address).
+ The leaf A-D route MUST include the PMSI Tunnel attribute with
the Tunnel Type set to Ingress Replication, and the Tunnel
Identifier set to a routable address of the advertising router.
The PMSI Tunnel attribute MUST carry a downstream assigned MPLS
label that is used to demultiplex the VPLS traffic received over
a unicast tunnel by the advertising router.
+ The Next Hop field of the MP_REACH_NLRI attribute of the route
SHOULD be set to the same IP address as the one carried in the
Originating Router's IP Address field of the route.
+ To constrain the distribution scope of this route the route MUST
carry the NO_ADVERTISE BGP community ([RFC1997]).
+ The ASBR constructs an IP-based Route Target extended community
by placing the IP address carried in the next hop of the received
Inter-AS VPLS A-D route in the Global Administrator field of the
community, with the Local Administrator field of this community
set to 0, and sets the Extended Communities attribute of the leaf
A-D route to that community. Note that this Route Target is the
same as the ASBR Import RT of the EBGP neighbor from which the
ASBR received the inter-AS VPLS A-D route.
Raggarwa, Kamite & Fang [Page 25]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
9.2.2.3. Leaf A-D Route received via EBGP
When an ASBR receives via EBGP a leaf A-D route, the ASBR accepts the
route only if (a) at least one of the Route Targets carried in the
message matches one of the import Route Targets configured on the
ASBR, and (b) the ASBR determines that the received route is the best
route to the destination carried in the NLRI of the route.
If the ASBR accepts the leaf A-D route, the ASBR looks for an
existing A-D route whose BGP-VPLS A-D NLRI has the same value as the
<RD, VE-ID> field of the leaf A-D route just accepted. If such an A-D
route is found, then the MPLS label carried in the PMSI Tunnel
attribute of the leaf A-D route is used to stitch a one hop ASBR-ASBR
LSP to the tail of the intra-AS tunnel segment associated with the
found A-D route.
9.2.2.4. Inter-AS A-D Route received via IBGP
In the context of this section we use the term "PE/ASBR router" to
denote either a PE or an ASBR router.
Note that a given inter-AS A-D route is advertised within a given AS
by only one ASBR as described above.
When a PE/ASBR router receives from one of its IBGP neighbors a BGP
Update message that carries an inter-AS A-D route, if (a) at least
one of the Route Targets carried in the message matches one of the
import Route Targets configured on the PE/ASBR, and (b) the PE/ASBR
determines that the received route is the best route to the
destination carried in the NLRI of the route, the PE/ASBR performs
the following operations. The best route determination is based as
described in [RFC4761] and clarified in [MULTI-HOMING].
If the router is an ASBR then the ASBR propagates the route to its
EBGP neighbors. When propagating the route to the EBGP neighbors the
ASBR MUST set the Next Hop field of the MP_REACH_NLRI attribute to a
routable IP address of the ASBR.
If the received inter-AS A-D route carries the PMSI Tunnel attribute
with the Tunnel Type set to LDP P2MP LSP, the PE/ASBR SHOULD join the
P-Multicast tree whose identity is carried in the PMSI Tunnel
attribute.
If the received inter-AS A-D route carries the PMSI Tunnel attribute
with the Tunnel Identifier set to RSVP-TE P2MP LSP, then the ASBR
that originated the route MUST establish an RSVP-TE P2MP LSP with the
local PE/ASBR as a leaf. This LSP MAY have been established before
Raggarwa, Kamite & Fang [Page 26]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
the local PE/ASBR receives the route, or MAY be established after the
local PE receives the route.
If the received inter-AS A-D route carries the PMSI Tunnel attribute
with the Tunnel Type set to LDP P2MP LSP, or RSVP-TE P2MP LSP, but
the attribute does not carry a label, then the P-Multicast tree, as
identified by the PMSI Tunnel attribute, is an intra-AS LSP segment
that is part of the inter-AS Tunnel for the <VPLS, VE ID> advertised
by the inter-AS A-D route and rooted at the PE that originated the A-
D route. If the PMSI Tunnel attribute carries a (upstream-assigned)
label, then a combination of this tree and the label identifies the
intra-AS segment. If the receiving router is an ASBR, this intra-AS
segment may further be stitched to ASBR-ASBR inter-AS segment of the
inter-AS tunnel. If the PE/ASBR has local receivers in the VPLS,
packets received over the intra-AS segment must be forwarded to the
local receivers using the local VSI.
9.3. Option (c): Non-Segmented Tunnels
In this model, there is a multi-hop EBGP peering between the PEs (or
BGP Route Reflector) in one AS and the PEs (or BGP Route Reflector)
in another AS. The PEs exchange BGP-VPLS NLRI or BGP-VPLS A-D NLRI,
along with PMSI Tunnel attribute, as in the intra-AS case described
in section "Demultiplexing P-Multicast Tree Traffic".
The PEs in different ASes use a non-segmented inter-AS P2MP tunnel
for VPLS multicast. A non-segmented inter-AS tunnel is a single
tunnel which spans AS boundaries. The tunnel technology cannot change
from one point in the tunnel to the next, so all ASes through which
the tunnel passes must support that technology. In essence, AS
boundaries are of no significance to a non-segmented inter-AS P2MP
tunnel.
This model requires no VPLS A-D routes in the control plane or VPLS
MAC address learning in the data plane on the ASBRs. The ASBRs only
need to participate in the non-segmented P2MP tunnel setup in the
control plane, and do MPLS label forwarding in the data plane.
When the tunneling technology is P2MP LSP signaled with mLDP, and one
does not use [RFC6512], the setup of non-segmented inter-AS P2MP
tunnels requires the P-routers in one AS to have IP reachability to
the loopback addresses of the PE routers in another AS. That is, the
reachability to the loopback addresses of PE routers in one AS MUST
be present in the IGP in another AS.
The data forwarding in this model is the same as in the intra-AS case
described in section "Demultiplexing P-Multicast Tree Traffic".
Raggarwa, Kamite & Fang [Page 27]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
An implementation MUST support this model.
10. Optimizing Multicast Distribution via Selective Trees
Whenever a particular multicast stream is being sent on an Inclusive
P-Multicast tree, it is likely that the data of that stream is being
sent to PEs that do not require it as the sites connected to these
PEs may have no receivers for the stream. If a particular stream has
a significant amount of traffic, it may be beneficial to move it to a
Selective P-Multicast tree which has at its leaves only those PEs,
connected to sites that have receivers for the multicast stream (or
at least includes fewer PEs that are attached to sites with no
receivers compared to an Inclusive tree).
A PE connected to the multicast source of a particular multicast
stream may be performing explicit tracking - i.e., it may know the
PEs that have receivers in the multicast stream. Section "Receiving
S-PMSI A-D routes by PEs" describes procedures that enable explicit
tracking. If this is the case Selective P-Multicast trees can also be
triggered on other criteria. For instance there could be a "pseudo
wasted bandwidth" criteria: switching to a Selective tree would be
done if the bandwidth multiplied by the number of "uninterested" PEs
(PEs that are receiving the stream but have no receivers) is above a
specified threshold. The motivation is that (a) the total bandwidth
wasted by many sparsely subscribed low-bandwidth groups may be large,
and (b) there's no point to moving a high-bandwidth group to a
Selective tree if all the PEs have receivers for it.
Switching a (C-S, C-G) stream to a Selective P-Multicast tree may
require the root of the tree to determine the egress PEs that need to
receive the (C-S, C-G) traffic. This is true in the following cases:
+ If the tunnel is a P2MP tree, such as a RSVP-TE P2MP Tunnel, the
PE needs to know the leaves of the tree before it can instantiate
the Selective tree.
+ If a PE decides to send traffic for multicast streams, belonging
to different VPLS instances, using one P-Multicast Selective
tree, such a tree is termed an Aggregate tree with a selective
mapping. The setting up of such an Aggregate tree requires the
ingress PE to know all the other PEs that have receivers for
multicast groups that are mapped onto the tree (see section
"Aggregation Considerations" for the rationale).
Raggarwa, Kamite & Fang [Page 28]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
+ If ingress replication is used and the ingress PE wants to send
traffic for (C-S, C-G)s to only those PEs that are on the path to
receivers to the (C-S,C-G)s.
For discovering the IP multicast group membership, for the above
cases, this document describes procedures that allow an ingress PE to
enable explicit tracking. Thus an ingress PE can request the IP
multicast membership from egress PEs for one or more C-multicast
streams. These procedures are described in section "Receiving S-PMSI
A-D routes by PEs".
The root of the Selective P-Multicast tree MAY decide to do explicit
tracking of the IP multicast stream only after it has determined to
move the stream to a Selective tree, or it MAY have been doing
explicit tracking all along. This document also describes explicit
tracking for a wildcard source and/or group in section "Receiving S-
PMSI A-D routes by PEs", which facilitates a Selective P-Multicast
tree only mode in which IP multicast streams are always carried on a
Selective P-Multicast tree. In the description on Selective P-
Multicast trees the notation C-S, is intended to represent either a
specific source address or a wildcard. Similarly C-G is intended to
represent either a specific group address or a wildcard.
The PE at the root of the tree MUST signal the leaves of the tree
that the (C-S, C-G) stream is now bound to the Selective Tree. Note
that the PE could create the identity of the P-Multicast tree prior
to the actual instantiation of the tunnel.
If the Selective tree is instantiated by a RSVP-TE P2MP LSP the PE at
the root of the tree MUST establish the P2MP RSVP-TE LSP to the
leaves. This LSP MAY have been established before the leaves receive
the Selective tree binding, or MAY be established after the leaves
receive the binding. A leaf MUST NOT switch to the Selective tree
until it receives the binding and the RSVP-TE P2MP LSP is setup to
the leaf.
10.1. Protocol for Switching to Selective Trees
Selective trees provide a PE the ability to create separate P-
Multicast trees for certain <C-S, C-G> streams. The source PE, that
originates the Selective tree, and the egress PEs, MUST use the
Selective tree for the <C-S, C-G> streams that are mapped to it. This
may require the source and egress PEs to switch to the Selective tree
from an Inclusive tree if they were already using an Inclusive tree
for the <C-S, C-G> streams mapped to the Selective tree.
Raggarwa, Kamite & Fang [Page 29]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
Once a source PE decides to setup a Selective tree, it MUST announce
the mapping of the <C-S, C-G> streams (which may be in different VPLS
instances) that are mapped to the tree to the other PEs using BGP.
After the egress PEs receive the announcement they setup their
forwarding path to receive traffic on the Selective tree if they have
one or more receivers interested in the <C-S, C-G> streams mapped to
the tree. Setting up the forwarding path requires setting up the
demultiplexing forwarding entries based on the top MPLS label (if
there is no inner label) or the inner label (if present) as described
in section "Establishing P-Multicast Trees".
When the P2MP LSP is established using mLDP, the egress PEs MAY
perform this switch to the Selective tree once the announcement from
the ingress PE is received, or MAY wait for a preconfigured timer to
do so, after receiving the announcement.
When the P2MP LSP protocol is P2MP RSVP-TE, an egress PE MUST perform
this switch to the Selective tree only after the announcement from
the ingress PE is received and the RSVP-TE P2MP LSP has been setup to
the egress PE. This switch MAY be done after waiting for a
preconfigured timer after these two steps have been accomplished.
A source PE MUST use the following approach to decide when to start
transmitting data on the Selective tree, if it is currently using an
Inclusive tree. After announcing the <C-S, C-G> stream mapping to a
Selective tree, the source PE MUST wait for a "switch-over" delay
before sending <C-S, C-G> stream on the Selective tree. It is
RECOMMENDED to allow this delay to be configurable. Once the "switch-
over" delay has elapsed, the source PE MUST send <C-S, C-G> stream on
the Selective tree. In no case is any <C-S, C-G> packet sent on both
Selective and Inclusive trees.
When a <C-S, C-G> stream is switched from an Inclusive to a Selective
tree, the purpose of running a switch-over timer is to minimize
packet loss without introducing packet duplication. However, jitter
may be introduced due to the difference in transit delays between the
Inclusive and Selective trees.
For best effect, the switch-over timer should be configured to a
value that is "just long enough" (a) to allow all the PEs to learn
about the new binding of <C-S, C-G> to a Selective tree, and (b) to
allow the PEs to construct the P-tunnel associated with the Selective
tree, if it doesn't already exist.
Raggarwa, Kamite & Fang [Page 30]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
10.2. Advertising (C-S, C-G) Binding to a Selective Tree
The ingress PE informs all the PEs that are on the path to receivers
of the (C-S, C-G) of the binding of the Selective tree to the (C-S,
C-G), using BGP. The BGP announcement is done by sending update for
the MCAST-VPLS address family using what we referred to as an "S-PMSI
A-D route". The format of the NLRI of this route is described in
section "Inclusive Tree/Selective Tree Identifier". The NLRI MUST be
constructed as follows:
+ The Route Distinguisher (RD) MUST be set to the RD configured
locally for the VPLS. This is required to uniquely identify the
<C-S, C-G> as the addresses could overlap between different VPLS
instances. This MUST be the same RD value used in the VPLS auto-
discovery process.
+ The Multicast Source field MUST contain the source address
associated with the C-multicast stream, and the Multicast Source
Length field is set appropriately to reflect this. If the source
address is a wildcard the source address is set to 0.
+ The Multicast Group field MUST contain the group address
associated with the C-multicast stream, and the Multicast Group
Length field is set appropriately to reflect this. If the group
address is a wildcard the group address is set to 0.
+ The Originating Router's IP Address field MUST be set to the IP
address that the (local) PE places in the BGP next-hop of the
BGP-VPLS A-D routes. Note that the <RD, Originating Router's IP
address> tuple uniquely identifies a given VPLS instance on a PE.
The PE constructs the rest of the Selective A-D route as follows.
Depending on the type of a P-Multicast tree used for the P-tunnel,
the PMSI tunnel attribute of the S-PMSI A-D route is constructed as
follows:
+ The PMSI tunnel attribute MUST contain the identity of the P-
Multicast tree (note that the PE could create the identity of the
tree prior to the actual instantiation of the tree).
+ If in order to establish the P-Multicast tree the PE needs to
know the leaves of the tree within its own AS, then the PE
obtains this information from the leaf A-D routes received from
other PEs/ASBRs within its own AS (as other PEs/ASBRs originate
leaf A-D routes in response to receiving the S-PMSI A-D route) by
setting the Leaf Information Required flag in the PMSI Tunnel
Raggarwa, Kamite & Fang [Page 31]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
attribute to 1. This enables explicit tracking for the multicast
stream(s) advertised by the S-PMSI A-D route.
+ If a PE originates S-PMSI A-D routes with the Leaf Information
Required flag in the PMSI Tunnel attribute set to 1, then the PE
MUST be (auto)configured with an import Route Target, which
controls acceptance of leaf A-D routes by the PE. (Procedures for
originating leaf A-D routes by the PEs that receive the S-PMSI A-
D route are described in section "Receiving S-PMSI A-D routes by
PEs.")
This Route Target is IP address specific. The Global
Administrator field of this Route Target MUST be set to the IP
address carried in the Next Hop of all the S-PMSI A-D routes
advertised by this PE (if the PE uses different Next Hops, then
the PE MUST be (auto)configured with multiple import RTs, one per
each such Next Hop). The Local Administrator field of this Route
Target MUST be set to 0.
If the PE supports Route Target Constrain [RFC4684], the PE
SHOULD advertise this import Route Target within its own AS using
Route Target Constrains. To constrain distribution of the Route
Target Constrain routes to the AS of the advertising PE these
routes SHOULD carry the NO_EXPORT Community ([RFC1997]).
+ A PE MAY aggregate two or more S-PMSIs originated by the PE onto
the same P-Multicast tree. If the PE already advertises S-PMSI A-
D routes for these S-PMSIs, then aggregation requires the PE to
re-advertise these routes. The re-advertised routes MUST be the
same as the original ones, except for the PMSI tunnel attribute.
If the PE has not previously advertised S-PMSI A-D routes for
these S-PMSIs, then the aggregation requires the PE to advertise
(new) S-PMSI A-D routes for these S-PMSIs. The PMSI Tunnel
attribute in the newly advertised/re-advertised routes MUST carry
the identity of the P-Multicast tree that aggregates the S-PMSIs.
If at least some of the S-PMSIs aggregated onto the same P-
Multicast tree belong to different VPLS instances, then all these
routes MUST carry an MPLS upstream assigned label [RFC5331]. If
all these aggregated S-PMSIs belong to the same VPLS, then the
routes MAY carry an MPLS upstream assigned label [RFC5331]. The
labels MUST be distinct on a per VPLS instance basis, and MAY be
distinct on a per route basis.
The Next Hop field of the MP_REACH_NLRI attribute of the route SHOULD
be set to the same IP address as the one carried in the Originating
Router's IP Address field.
Raggarwa, Kamite & Fang [Page 32]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
By default the set of Route Targets carried by the route MUST be the
same as the Route Targets carried in the BGP-VPLS A-D route
originated from the VSI. The default could be modified via
configuration.
10.3. Receiving S-PMSI A-D routes by PEs
Consider a PE that receives an S-PMSI A-D route. If one or more of
the VSIs on the PE have their import Route Targets that contain one
or more of the Route Targets carried by the received S-PMSI A-D
route, then for each such VSI the PE performs the following.
Procedures for receiving an S-PMSI A-D route by a PE (both within and
outside of the AS of the PE that originates the route) are the same
as specified in section "Inter-AS A-D route received via IBGP" except
that (a) instead of Inter-AS A-D routes the procedures apply to S-
PMSI A-D routes, and (b) the rules for determining whether the
received S-PMSI A-D route is the best route to the destination
carried in the NLRI of the route, are the same as BGP path selection
rules and may be modified by policy, and (c) a PE performs procedures
specified in that section only if in addition to the criteria
specified in that section the following is true:
+ If as a result of multicast state snooping on the PE-CE
interfaces, the PE has snooped state for at least one multicast
join that matches the multicast source and group advertised in
the S-PMSI A-D route. Further if the oifs (outgoing interfaces)
for this state contains one or more interfaces to the locally
attached CEs. When the multicast signaling protocol among the CEs
is IGMP, then snooping and associated procedures are defined in
[RFC4541]. The snooped state is determined using these
procedures. When the multicast signaling protocol among the CEs
is PIM, the procedures in [RFC4541] are not sufficient to
determine the snooped state. The additional details required to
determine the snooped state when CE-CE protocol is PIM are for
further study. When such procedures are defined it is expected
that the procedures in this section will apply to the snooped
state created as a result of PIM as PE-CE protocol.
The snooped state is said to "match" the S-PMSI A-D route if any of
the following is true:
Raggarwa, Kamite & Fang [Page 33]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
+ The S-PMSI A-D route carries (C-S, C-G) and the snooped state is
for (C-S, C-G) or for (C-*, C-G), OR
+ The S-PMSI A-D route carries (C-*, C-G) and (a) the snooped
state is for (C-*, C-G) OR (b) the snooped state is for at least
one multicast join with the multicast group address equal to C-G
and there doesn't exist another S-PMSI A-D route that carries (C-
S, C-G) where C-S is the source address of the snooped state.
+ The S-PMSI A-D route carries (C-S, C-*) and (a) the snooped
state is for at least one multicast join with the multicast
source address equal to C-S, and (b) there doesn't exist another
S-PMSI A-D route that carries (C-S, C-G) where C-G is the group
address of the snooped state.
+ The S-PMSI A-D route carries (C-*, C-*) and there is no other S-
PMSI A-D route that matches the snooped state as per the above
conditions.
Note if the above conditions are true, and if the received S-PMSI A-D
route has a PMSI Tunnel attribute with the Leaf Information Required
flag set to 1, then the PE originates a leaf A-D route, constructed
as follows:
+ The route carries a single MCAST-VPLS NLRI with the Route Key
field set to the MCAST-VPLS NLRI of the received S-PMSI A-D
route.
+ The Originating Router's IP address set to the IP address of the
PE (this MUST be a routable IP address).
+ The PE constructs an IP-based Route Target Extended Community by
placing the IP address carried in the Next Hop of the received S-
PMSI A-D route in the Global Administrator field of the
Community, with the Local Administrator field of this Community
set to 0 and setting the Extended Communities attribute of the
leaf A-D route to that Community.
+ The Next Hop field of the MP_REACH_NLRI attribute of the route
MUST be set to the same IP address as the one carried in the
Originating Router's IP Address field of the route.
+ To constrain the distribution scope of this route, the route
MUST carry the NO_EXPORT Community [RFC1997], except for the
inter-AS scenario with option (c).
Once the leaf A-D route is constructed, the PE advertises this route
Raggarwa, Kamite & Fang [Page 34]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
into IBGP.
In addition to the procedures specified in section "Inter-AS A-D
route received via IBGP" the PE MUST set up its forwarding path to
receive traffic, for each multicast stream in the matching snooped
state, from the tunnel advertised by the S-PMSI A-D route (the PE
MUST switch to the Selective tree).
When a new snooped state is created by a PE then the PE MUST first
determine if there is a S-PMSI A-D route that matches the snooped
state as per the conditions described above. If such a S-PMSI A-D
route is found, then the PE MUST follow the procedures described in
this section, for that particular S-PMSI A-D route. If later on the
snooped state ages out and is deleted from the PE, the PE SHOULD
withdraw the leaf A-D route that it had originated in response to the
S-PMSI A-D route.
10.4. Inter-AS Selective Tree
Inter-AS Selective trees support all three options of inter-AS VPLS
service, option (a), (b) and (c), that are supported by Inter-AS
Inclusive trees. They are constructed in a manner that is very
similar to Inter-AS Inclusive trees.
For option (a) and option (b) support inter-AS Selective trees are
constructed without requiring a single P-Multicast tree to span
multiple ASes. This allows individual ASes to potentially use
different P-tunneling technologies. There are two variants of this.
One that requires MAC and IP multicast lookup on the ASBRs and
another that does not require MAC/IP multicast lookup on the ASBRs
and instead builds segmented inter-AS Selective trees.
Segmented Inter-AS Selective trees can also be used with option (c),
unlike Segmented Inter-AS Inclusive trees. This is because the S-PMSI
A-D routes can be exchanged via ASBRs (even though BGP VPLS A-D
routes are not exchanged via ASBRs).
In the case of Option (c) an Inter-AS Selective tree may also be a
non-segmented P-Multicast tree that spans multiple ASes.
10.4.1. VSIs on the ASBRs
The requirements on ASBRs, when VSIs are present on the ABSRs,
include the requirements presented in section "Inter-AS Inclusive P-
Multicast Tree A-D/Binding". The source ASBR (that receives traffic
from another AS) may independently decide whether it wishes to use
Raggarwa, Kamite & Fang [Page 35]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
Selective trees or not. If it uses Selective trees the source ASBR
MUST perform a MAC lookup to determine the Selective tree to forward
the VPLS packet on.
10.4.1.1. VPLS Inter-AS Selective Tree A-D Binding
The mechanisms for propagating S-PMSI A-D routes are the same as the
intra-AS case described in section "MCAST-VPLS NLRI". The BGP
Selective tree A-D routes generated by PEs in an AS MUST NOT be
propagated outside the AS.
10.4.2. Inter-AS Segmented Selective Trees
Inter-AS Segmented Selective trees MUST be used when option (b) is
used to provide the inter-AS VPLS service. They MAY be used when
option (c) is used to provide the inter-AS VPLS service.
A Segmented inter-AS Selective Tunnel is constructed similar to an
inter-AS Segmented Inclusive Tunnel. Namely, such a tunnel is
constructed as a concatenation of tunnel segments. There are two
types of tunnel segments: an intra-AS tunnel segment (a segment that
spans ASBRs within the same AS), and inter-AS tunnel segment (a
segment that spans adjacent ASBRs in adjacent ASes). ASes that are
spanned by a tunnel are not required to use the same tunneling
mechanism to construct the tunnel - each AS may pick up a tunneling
mechanism to construct the intra-AS tunnel segment of the tunnel, in
its AS.
The PE that decides to set up a Selective tree, advertises the
Selective tree to multicast stream binding using an S-PMSI A-D route
as per procedures in section "Advertising (C-S, C-G) Binding to a
Selective Tree", to the routers in its own AS.
An S-PMSI A-D route advertised outside the AS, to which the
originating PE belongs, will be referred to as an inter-AS Selective
Tree A-D route (although this route is originated by a PE as an
intra-AS route it is referred to as an inter-AS route outside the
AS).
10.4.2.1. Handling S-PMSI A-D routes by ASBRs
Procedures for handling an S-PMSI A-D route by ASBRs (both within and
outside of the AS of the PE that originates the route) are the same
as specified in section "Propagating VPLS BGP A-D routes to other
Raggarwa, Kamite & Fang [Page 36]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
ASes", except that instead of Inter-AS BGP-VPLS A-D routes and the
BGP-VPLS A-D NLRI these procedures apply to S-PMSI A-D routes and the
S-PMSI A-D NLRI.
In addition to these procedures an ASBR advertises a leaf A-D route
in response to an S-PMSI A-D route only if:
+ The S-PMSI A-D route was received via EBGP from another ASBR and
the ASBR merges the S-PMSI A-D route into an Inter-AS BGP VPLS A-
D route as described in the next section. OR
+ The ASBR receives a leaf A-D route from a downstream PE or ASBR
in response to the S-PMSI A-D route, received from an upstream PE
or ASBR, that the ASBR propagated inter-AS to downstream ASBRs
and PEs.
+ The ASBR has snooped state from local CEs that matches the NLRI
carried in the S-PMSI A-D route as per the following rules:
i) The NLRI encodes (C-S, C-G) which is the same as the snooped
(C-S, C-G)
ii) The NLRI encodes (*, C-G) and there is snooped state for at
least one (C-S, C-G) and there is no other matching S-PMSI A-D
route for (C-S, C-G) OR there is snooped state for (*, C-G)
iii) The NLRI encodes (*, *) and there is snooped state for at
least one (C-S, C-G) or (*, C-G) and there is no other matching
S-PMSI A-D route for that (C-S, C-G) or (*, C-G) respectively.
The C-multicast data traffic is sent on the Selective tree by the
originating PE. When it reaches an ASBR that is on the Inter-AS
segmented tree, it is delivered to local receivers, if any. It is
then forwarded on any inter-AS or intra-AS segments that exist on the
Inter-AS Selective Segmented tree. If the Inter-AS Segmented
Selective Tree is merged onto an Inclusive tree, as described in the
next section, the data traffic is forwarded onto the Inclusive tree.
10.4.2.1.1. Merging Selective Tree into an Inclusive Tree
Consider the situation where:
Raggarwa, Kamite & Fang [Page 37]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
+ An ASBR is receiving (or expecting to receive) inter-AS (C-S, C-
G) data from upstream via a Selective tree.
+ The ASBR is sending (or expecting to send) the inter-AS (C-S, C-
G) data downstream via an Inclusive tree.
This situation may arise if the upstream providers have a policy of
using Selective trees but the downstream providers have a policy of
using Inclusive trees. To support this situation, an ASBR MAY, under
certain conditions, merge one or more upstream Selective trees into a
downstream Inclusive tree. Note that this can be the case only for
option (b) and not for option (c) as for option (c) the ASBRs do not
have Inclusive tree state.
A Selective tree (corresponding to a particular S-PMSI A-D route) MAY
be merged by a particular ASBR into an Inclusive tree (corresponding
to a particular Inter-AS BGP VPLS A-D route) if and only if the
following conditions all hold:
+ The S-PMSI A-D route and the Inter-AS BGP VPLS A-D route
originate in the same AS. The Inter-AS BGP VPLS A-D route carries
the originating AS in the AS_PATH attribute of the route. The S-
PMSI A-D route carries the originating AS in the AS_PATH
attribute of the route.
+ The S-PMSI A-D route and the Inter-AS BGP VPLS A-D route have
exactly the same set of RTs.
An ASBR performs merging by stitching the tail end of the P-tunnel,
as specified in the PMSI Tunnel attribute of the S-PMSI A-D route
received by the ASBR, to the head of the P-tunnel, as specified in
the PMSI Tunnel attribute of the Inter-AS BGP VPLS A-D route re-
advertised by the ASBR.
An ASBR that merges an S-PMSI A-D route into an Inter-AS BGP VPLS A-D
route MUST NOT re-advertise the S-PMSI A-D route.
10.4.3. Inter-AS Non-Segmented Selective trees
Inter-AS Non-segmented Selective trees MAY be used in the case of
option (c).
In this method, there is a multi-hop EBGP peering between the PEs (or
a Route Reflector) in one AS and the PEs (or Route Reflector) in
another AS. The PEs exchange BGP Selective tree A-D routes, along
Raggarwa, Kamite & Fang [Page 38]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
with PMSI Tunnel attribute, as in the intra-AS case described in
section "Option (c): Non-Segmented Tunnels".
The PEs in different ASes use a non-segmented Selective inter-AS P2MP
tunnel for VPLS multicast.
This method requires no VPLS information (in either the control or
the data plane) on the ASBRs. The ASBRs only need to participate in
the non-segmented P2MP tunnel setup in the control plane, and do MPLS
label forwarding in the data plane.
The data forwarding in this model is the same as in the intra-AS case
described in section "Establishing P-Multicast Trees".
11. BGP Extensions
This section describes the encoding of the BGP extensions required by
this document.
11.1. Inclusive Tree/Selective Tree Identifier
Inclusive P-Multicast tree and Selective P-Multicast tree
advertisements carry the P-Multicast tree identifier.
This document reuses the BGP attribute, called PMSI Tunnel attribute
that is defined in [RFC6514].
This document supports only the following Tunnel Types when PMSI
Tunnel attribute is carried in VPLS A-D or VPLS S-PMSI A-D routes:
+ 0 - No tunnel information present
+ 1 - RSVP-TE P2MP LSP
+ 2 - LDP P2MP LSP
+ 6 - Ingress Replication
11.2. MCAST-VPLS NLRI
This document defines a new BGP NLRI, called the MCAST-VPLS NLRI.
Following is the format of the MCAST-VPLS NLRI:
+-----------------------------------+
| Route Type (1 octet) |
+-----------------------------------+
Raggarwa, Kamite & Fang [Page 39]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
| Length (1 octet) |
+-----------------------------------+
| Route Type specific (variable) |
+-----------------------------------+
The Route Type field defines encoding of the rest of MCAST-VPLS NLRI
(Route Type specific MCAST-VPLS NLRI).
The Length field indicates the length in octets of the Route Type
specific field of MCAST-VPLS NLRI.
This document defines the following Route Types for A-D routes:
+ 3 - Selective Tree A-D route;
+ 4 - Leaf A-D route.
The MCAST-VPLS NLRI is carried in BGP using BGP Multiprotocol
Extensions [RFC4760] with an AFI of 25 (L2VPN AFI), and an SAFI of
MCAST-VPLS. The NLRI field in the MP_REACH_NLRI/MP_UNREACH_NLRI
attribute contains the MCAST-VPLS NLRI (encoded as specified above).
In order for two BGP speakers to exchange labeled MCAST-VPLS NLRI,
they must use BGP Capabilities Advertisement to ensure that they both
are capable of properly processing such NLRI. This is done as
specified in [RFC4760], by using capability code 1 (multiprotocol
BGP) with an AFI of 25 and a SAFI of MCAST-VPLS.
The following describes the format of the Route Type specific MCAST-
VPLS NLRI for various Route Types defined in this document.
11.2.1. S-PMSI A-D route
An S-PMSI A-D route type specific MCAST-VPLS NLRI consists of the
following:
+-----------------------------------+
| RD (8 octets) |
+-----------------------------------+
| Multicast Source Length (1 octet) |
+-----------------------------------+
| Multicast Source (Variable) |
+-----------------------------------+
| Multicast Group Length (1 octet) |
+-----------------------------------+
| Multicast Group (Variable) |
+-----------------------------------+
| Originating Router's IP Addr |
Raggarwa, Kamite & Fang [Page 40]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
+-----------------------------------+
The RD is encoded as described in [RFC4364].
The Multicast Source field contains the C-S address i.e the address
of the multicast source. If the Multicast Source field contains an
IPv4 address, then the value of the Multicast Source Length field is
32. If the Multicast Source field contains an IPv6 address, then the
value of the Multicast Source Length field is 128. The value of the
Multicast Source Length field may be set to 0 to indicate a wildcard.
The Multicast Group field contains the C-G address i.e. the address
of the multicast group. If the Multicast Group field contains an IPv4
address, then the value of the Multicast Group Length field is 32.
If the Multicast Group field contains an IPv6 address, then the value
of the Multicast Group Length field is 128. The Multicast Group
Length field may be set to 0 to indicate a wildcard.
Whether the Originating Router's IP Address field carries an IPv4 or
IPv6 address is determined from the value of the Length field of the
MCAST-VPLS NLRI. If the Multicast Source field contains an IPv4
address and the Multicast Group field contains an IPv4 address, then
the value of the Length field is 22 bytes if the Originating Router's
IP address carries an IPv4 address and 34 bytes if it is an IPv6
address. If the Multicast Source and Multicast Group fields contain
IPv6 addresses, then the value of the Length field is 46 bytes if the
Originating Router's IP address carries an IPv4 address and 58 bytes
if it is an IPv6 address. The following table summarizes the above.
Multicast Multicast Originating Router's Length
Source Group IP Address
IPv4 IPv4 IPv4 22
IPv4 IPv4 IPv6 34
IPv6 IPv6 IPv4 46
IPv6 IPv6 IPv6 58
Usage of Selective Tree A-D routes is described in section
"Optimizing Multicast Distribution via Selective Trees".
11.2.2. Leaf A-D route
A leaf A-D route type specific MCAST-VPLS NLRI consists of the
following:
+-----------------------------------+
Raggarwa, Kamite & Fang [Page 41]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
| Route Key (variable) |
+-----------------------------------+
| Originating Router's IP Addr |
+-----------------------------------+
Whether the Originating Router's IP Address field carries an IPv4 or
IPv6 address is determined from the Length field of the MCAST-VPLS
NLRI and the length of the Route Key field. From these two length
fields one can compute the length of the Originating Router's IP
Address. If this computed length is 4 then the address is an IPv4
address and if its 16 then the address is an IPv6 address.
Usage of leaf A-D routes is described in sections "Inter-AS Inclusive
P-Multicast tree A-D/Binding" and "Optimizing Multicast Distribution
via Selective trees".
12. Aggregation Considerations
This document does not specify the mandatory implementation of any
particular set of rules for determining whether or not the Inclusive
or Selective trees of two particular VPLS instances are to be
instantiated by the same Aggregate Inclusive/Selective Tree. This
determination can be made by implementation-specific heuristics, by
configuration, or even perhaps by the use of offline tools.
This section discusses potential methodologies with respect to
aggregation.
In general the heuristic used to decide which VPLS instances or (C-S,
C-G) entries to aggregate is implementation dependent. It is also
conceivable that offline tools can be used for this purpose. This
section discusses some tradeoffs with respect to aggregation.
The "congruency" of aggregation is defined by the amount of overlap
in the leaves of the client trees that are aggregated on an SP tree.
For Aggregate Inclusive trees the congruency depends on the overlap
in the membership of the VPLS instances that are aggregated on the
Aggregate Inclusive tree. If there is complete overlap aggregation is
perfectly congruent. As the overlap between the VPLS instances that
are aggregated reduces, the congruency reduces.
From the above definition of "congruency" it follows that in order
for a given PE to determine the congruency of the client trees that
this PE could aggregate, the PE has to know the leaves of these
client trees. This is irrespective of whether the aggregated SP tree
is established using mLDP or RSVP-TE.
Raggarwa, Kamite & Fang [Page 42]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
If aggregation is done such that it is not perfectly congruent a PE
may receive traffic for VPLS instances to which it doesn't belong. As
the amount of multicast traffic in these unwanted VPLS instantes
increases aggregation becomes less optimal with respect to delivered
traffic. Hence there is a tradeoff between reducing multicast state
in the core and delivering unwanted traffic.
An implementation should provide knobs to control aggregation based
on the congruency of the tree to be aggregated. This will allow an SP
to deploy aggregation depending on the VPLS membership and traffic
profiles in its network. If different PEs are setting up Aggregate
Inclusive trees this will also allow an SP to engineer the maximum
amount of unwanted VPLS instances that a particular PE may receive
traffic for.
The state/bandwidth optimality trade-off can be further improved by
having a versatile many-to-many association between client trees and
provider trees. Thus a VPLS instance can be mapped to multiple
Aggregate trees. The mechanisms for achieving this are for further
study. Also it may be possible to use both ingress replication and an
Aggregate tree for a particular VPLS. Mechanisms for achieving this
are also for further study.
13. Data Forwarding
13.1. MPLS Tree Encapsulation
13.1.1. Mapping multiple VPLS instances to a P2MP LSP
The following diagram shows the progression of the VPLS multicast
packet as it enters and leaves the SP network when MPLS trees are
being used for multiple VPLS instances. RSVP-TE P2MP LSPs are
examples of such trees.
Packets received Packets in transit Packets forwarded
at ingress PE in the service by egress PEs
provider network
+---------------+
|MPLS Tree Label|
+---------------+
| VPLS Label |
++=============++ ++=============++ ++=============++
||C-Ether Hdr || || C-Ether Hdr || || C-Ether Hdr ||
Raggarwa, Kamite & Fang [Page 43]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
++=============++ >>>>> ++=============++ >>>>> ++=============++
|| C-IP Header || || C-IP Header || || C-IP Header ||
++=============++ >>>>> ++=============++ >>>>> ++=============++
|| C-Payload || || C-Payload || || C-Payload ||
++=============++ ++=============++ ++=============++
When an ingress PE receives a packet, the ingress PE using the
procedures defined in [RFC4761] [RFC4762] determines the VPLS
instance associated with the packet. If the packet is an IP multicast
packet, and the ingress PE uses an Aggregate Selective tree for the
(C-S, C-G) carried in the packet, then the ingress PE pushes the VPLS
Label associated with the VPLS instance on the ingress PE and the
MPLS Tree Label associate with the Aggregate Selective tree, and
sends the packet over the P2MP LSP associated with the Aggregate
Selective tree. Otherwise, if the ingress PE does not use an
Aggregate Selective tree for the (C-S, C-G), or the packet is either
non-IP multicast or broadcast, the ingress PE pushes the VPLS label
associated with the VPLS instance on the ingress PE and the MPLS Tree
Label associated with the Aggregate Inclusive tree, and sends the
packet over the P2MP LSP associated with the Aggregate Inclusive
tree.
The egress PE does a lookup on the outer MPLS tree label, and
determines the MPLS forwarding table in which to lookup the inner
MPLS label (VPLS label). This table is specific to the tree label
space (as identified by the MPLS Tree label). The inner label (VPLS
label) is unique within the context of the root of the tree (as it is
assigned by the root of the tree, without any coordination with any
other nodes). Thus it is not unique across multiple roots. So, to
unambiguously identify a particular VPLS one has to know the VPLS
label, and the context within which that label is unique. The context
is provided by the outer MPLS label (MPLS Tree label) [RFC5331].
The outer MPLS label is popped. The lookup of the resulting MPLS
label determines the VSI in which the egress PE needs to do the C-
multicast data packet lookup. It then pops the inner MPLS label and
sends the packet to the VSI for multicast data forwarding.
13.1.2. Mapping one VPLS instance to a P2MP LSP
The following diagram shows the progression of the VPLS multicast
packet as it enters and leaves the SP network when a given MPLS tree
is being used for a single VPLS instance. RSVP-TE P2MP LSPs are
examples of such trees.
Raggarwa, Kamite & Fang [Page 44]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
Packets received Packets in transit Packets forwarded
at ingress PE in the service by egress PEs
provider network
+---------------+
|MPLS Tree Label|
++=============++ ++=============++ ++=============++
||C-Ether Hdr || || C-Ether Hdr || || C-Ether Hdr ||
++=============++ >>>>> ++=============++ >>>>> ++=============++
|| C-IP Header || || C-IP Header || || C-IP Header ||
++=============++ >>>>> ++=============++ >>>>> ++=============++
|| C-Payload || || C-Payload || || C-Payload ||
++=============++ ++=============++ ++=============++
When an ingress PE receives a packet, the ingress PE using the
procedures defined in [RFC4761] [RFC4762] determines the VPLS
instance associated with the packet. If the packet is an IP multicast
packet, and the ingress PE uses a Selective tree for the (C-S, C-G)
carried in the packet, then the ingress PE pushes the MPLS Tree Label
associate with the Selective tree, and sends the packet over the P2MP
LSP associated with the Selective tree. Otherwise, if the ingress PE
does not use a Selective tree for the (C-S, C-G), or the packet is
either non-IP multicast or broadcast, the ingress PE pushes the MPLS
Tree Label associated with the Inclusive tree, and sends the packet
over the P2MP LSP associated with the Inclusive tree.
The egress PE does a lookup on the MPLS tree label and determines the
VSI in which the receiver PE needs to do the C-multicast data packet
lookup. It then pops the MPLS label and sends the packet to the VSI
for multicast data forwarding.
14. VPLS Data Packet Treatment
If the destination MAC address of a VPLS packet received by an
ingress PE from a VPLS site is a multicast address, a P-Multicast
tree SHOULD be used to transport the packet, if possible. If the
packet is an IP multicast packet and a Selective tree exists for that
multicast stream, the Selective tree MUST be used. Else if a (C-*,
C-*) Selective tree exists for the VPLS it SHOULD be used. Else if an
Inclusive tree exists for the VPLS, it SHOULD be used.
If the destination MAC address of a VPLS packet is a broadcast
address, it is flooded. If a (C-*, C-*) Selective tree exists for the
Raggarwa, Kamite & Fang [Page 45]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
VPLS the PE SHOULD flood over it. Else if Inclusive tree exists for
the VPLS the PE SHOULD flood over it. Else the PE MUST flood the
packet using the procedures in [RFC4761] or [RFC4762].
If the destination MAC address of a packet is a unicast address and
it has not been learned, the packet MUST be sent to all PEs in the
VPLS. Inclusive P-Multicast trees or a Selective P-Multicast tree
bound to (C-*, C-*) SHOULD be used for sending unknown unicast MAC
packets to all PEs. When this is the case the receiving PEs MUST
support the ability to perform MAC address learning for packets
received on a multicast tree. In order to perform such learning, the
receiver PE MUST be able to determine the sender PE when a VPLS
packet is received on a P-Multicast tree. This further implies that
the MPLS P-Multicast tree technology MUST allow the egress PE to
determine the sender PE from the received MPLS packet.
When a receiver PE receives a VPLS packet with a source MAC address,
that has not yet been learned, on a P-Multicast tree, the receiver PE
determines the PW to the sender PE. The receiver PE then creates
forwarding state in the VPLS instance with a destination MAC address
being the same as the source MAC address being learned, and the PW
being the PW to the sender PE.
It should be noted that when a sender PE that is sending packets
destined to an unknown unicast MAC address over a P-Multicast tree
learns the PW to use for forwarding packets destined to this unicast
MAC address, it might immediately switch to transport such packets
over this particular PW. Since the packets were initially being
forwarded using a P-Multicast tree, this could lead to packet
reordering. This constraint should be taken into consideration if
unknown unicast frames are forwarded using a P-Multicast tree,
instead of multiple PWs based on [RFC4761] or [RFC4762].
An implementation SHOULD support the ability to transport unknown
unicast traffic over Inclusive P-Multicast trees. Furthermore, an
implementation MUST support the ability to perform MAC address
learning for packets received on a P-Multicast tree.
15. Security Considerations
Security considerations discussed in [RFC4761] and [RFC4762] apply to
this document. This section describes additional considerations.
As mentioned in [RFC4761], there are two aspects to achieving data
privacy and protect against denial-of-service attacks in a VPLS:
securing the control plane and protecting the forwarding path.
Compromise of the control plane could result in a PE sending
Raggarwa, Kamite & Fang [Page 46]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
multicast data belonging to some VPLS to another VPLS, or black-
holing VPLS multicast data, or even sending it to an eavesdropper;
none of which are acceptable from a data privacy point of view. In
addition, compromise of the control plane could result in black-
holing VPLS multicast data and could provide opportunities for
unauthorized VPLS multicast usage (e.g., exploiting traffic
replication within a multicast tree to amplify a denial of service
attack based on sending large amounts of traffic).
The mechanisms in this document use BGP for the control plane. Hence
techniques such as in [RFC5925] help authenticate BGP messages,
making it harder to spoof updates (which can be used to divert VPLS
traffic to the wrong VPLS) or withdrawals (denial-of-service
attacks). In the multi-AS methods (b) and (c) described in section
"Inter-AS Inclusive P-Multicast Tree A-D/Binding" this also means
protecting the inter-AS BGP sessions, between the ASBRs, the PEs, or
the Route Reflectors.
Note that [RFC5925] will not help in keeping MPLS labels, associated
with P2MP LSPs or the upstream MPLS labels used for aggregation,
private -- knowing the labels, one can eavesdrop on VPLS traffic.
However, this requires access to the data path within a Service
Provider network, which is assumed to be composed of trusted
nodes/links.
One of the requirements for protecting the data plane is that the
MPLS labels are accepted only from valid interfaces. This applies
both to MPLS labels associated with P2MP LSPs and also applies to the
upstream assigned MPLS labels. For a PE, valid interfaces comprise
links from other routers in PE's own AS. For an ASBR, valid
interfaces comprise links from other routers in ASBR's own AS, and
links from other ASBRs in ASes that have instances of a given VPLS.
It is especially important in the case of multi-AS VPLS instances
that one accept VPLS packets only from valid interfaces.
16. IANA Considerations
This document defines a new NLRI, called MCAST-VPLS, to be carried in
BGP using multiprotocol extensions. It requires assignment of a new
SAFI. This is to be assigned by IANA.
This document defines a BGP optional transitive attribute, called
PMSI attribute. This is the same attribute as the one defined in
[RFC6514] and the code point for this attribute has already been
assigned by IANA as 22 [BGP-IANA]. Hence no further action is
required from IANA regarding this attribute.
Raggarwa, Kamite & Fang [Page 47]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
17. Acknowledgments
Many thanks to Thomas Morin for his support of this work.
We would also like to thank authors of [RFC6514] and [RFC6513], as
the details of the inter-AS segmented tree procedures in this
document, as well as some text that describes these procedures have
benefited from those in [RFC6514] and [RFC6513]. The same applies to
the notion of Inclusive and Selective trees, as well as the
procedures for switching from Inclusive to Selective trees.
We would also like to thank Nabil Bitar, Stewart Bryant, Wim
Henderickx, and Eric Rosen for their review and comments.
18. Normative References
[RFC2119] S. Bradner, "Key words for use in RFCs to Indicate
Requirement Levels.", RFC 2119, March 1997
[RFC3209] D. Awduche, et. al., "RSVP-TE: Extensions to RSVP for LSP
Tunnels", RFC 3209, December 2001
[RFC4760] T. Bates, et. al., "Multiprotocol Extensions for BGP-4",
RFC 4760, January 2007.
[RFC4761] K. Kompella, Y. Rekther, "Virtual Private LAN Service using
BGP for Auto-Discovery and Signaling", RFC 4761, January 2007.
[RFC4762] M. Lasserre, V. Kompella, "Virtual Private LAN Services
over MPLS Label Distribution Protocol (LDP) Signaling", RFC 4762,
January 2007.
[RFC5036] L. Andersson, et. al., "LDP Specification", RFC 5036,
October 2007
[RFC5331] R. Aggarwal, Y. Rekhter, E. Rosen, "MPLS Upstream Label
Assignment and Context Specific Label Space", RFC 5331, August 2008.
[RFC6511] Z. Ali, G. Swallow, R. Aggarwal, "Non PHP behavior and
out-of-band mapping for RSVP-TE LSPs", RFC 6511, February 2012.
[RFC6512] IJ. Wijnands, et. al., "Using Multipoint LDP When the
Backbone Has No Route to the Root", RFC6512, February 2012
Raggarwa, Kamite & Fang [Page 48]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
19. Informative References
[RFC6514] R. Aggarwal, E. Rosen, Y. Rekhter, T. Morin, "BGP Encodings
for Multicast in MPLS/BGP IP VPNs". RFC 6514, February 2012.
[RFC6513] E. Rosen, R. Aggarwal, "Multicast in MPLS/BGP IP VPNs", RFC
6513, February 2012.
[RFC6388] I. Minei et. al, "Label Distribution Protocol Extensions
for Point-to-Multipoint and Multipoint-to-Multipoint Label Switched
Paths", RFC 6388, November 2011.
[RFC6074] E. Rosen et. al., "Provisioning, Autodiscovery, and
Signaling in L2VPNs", RFC 6074, January 2011.
[RFC5925] J. Touch, et. al., "The TCP Authentication Option",
RFC5925, June 2010.
[RFC5501] Y. kamite, et. al., "Requirements for Multicast Support in
Virtual Private LAN Services", RFC 5501, January 2009.
[RFC5332] T. Eckert, E. Rosen, R. Aggarwal, Y. Rekhter, "MPLS
Multicast Encapsulations", RFC 5332, August 2008.
[RFC4684] P. Marques et. al., "Constrained Route Distribution for
Border Gateway Protocol/MultiProtocol Label Switching (BGP/MPLS)
Internet Protocol (IP) Virtual Private Networks (VPNs)", RFC 4684,
November 2006.
[RFC4875] R. Aggarwal et. al, "Extensions to RSVP-TE for Point to
Multipoint TE LSPs", RFC 4857, May 2007.
[RFC4601] B. Fenner, et. al., "PIM-SM Protocol Specification", RFC
4601, August 2006.
[RFC4541] M. Christensen et. al., "Considerations for Internet Group
Management Protocol (IGMP) and Multicast Listener Discovery (MLD)
Snooping Switches", RFC 4541, May 2006.
[RFC4447] L. Martini et. al., "Pseudowire Setup and Maintenance Using
the Label Distribution Protocol (LDP)", RFC 4447, April 2006.
[RFC4364] "BGP MPLS VPNs", E. Rosen, Y.Rekhter, RFC4364, February
2006.
[RFC3810] R. Vida, et. al., "Multicast Listener Discovery Version 2
(MLDv2) for IPv6", RFC 3810, June 2004
Raggarwa, Kamite & Fang [Page 49]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
[RFC3376] B. Cain, et. al., "Internet Group Management Protocol,
Version 3", RFC3376, October 2002
[RFC2710] S., Deering, et. al., "Multicast Listener Discovery (MLD)
for IPv6", RFC2710, October 1999
[RFC2236] W. Fenner, "Internet Group Management Protocol, Version 2",
RFC2236, November 1997
[RFC1997] R. Chandra, et. al., "BGP Communities Attribute", RFC 1997,
August 1996.
[MULTI-HOMING] K. Kompella et. al., "Multi-homing in BGP-based
Virtual Private LAN Service", draft-ietf-l2vpn-vpls-multihoming Work
in Progress.
[BGP-IANA] http://www.iana.org/assignments/bgp-parameters
20. Author's Address
Rahul Aggarwal
998 Lucky Avenue
Menlo Park, CA 94025
USA
Phone: +1-415-806-5527
Email: raggarwa_1@yahoo.com
Yuji Kamite
NTT Communications Corporation
Tokyo Opera City Tower
3-20-2 Nishi Shinjuku, Shinjuku-ku,
Tokyo 163-1421,
Japan
Email: y.kamite@ntt.com
Luyuan Fang
Cisco Systems
111 Wood Avenue South
Iselin, NJ 08830
USA
Email: lufang@cisco.com
Yakov Rekhter
Juniper Networks
Raggarwa, Kamite & Fang [Page 50]
Internet Draft draft-ietf-l2vpn-vpls-mcast-16.txt November 2013
1194 North Mathilda Ave.
Sunnyvale, CA 94089
USA
Email: yakov@juniper.net
Chaitanya Kodeboniya
Cisco Systems
Email: ckodeboy@cisco.com
Raggarwa, Kamite & Fang [Page 51]
