Internet DRAFT - draft-ietf-mpls-rfc3107bis
draft-ietf-mpls-rfc3107bis
Internet Engineering Task Force E. Rosen
Internet-Draft Juniper Networks, Inc.
Obsoletes: 3107 (if approved) August 17, 2017
Intended status: Standards Track
Expires: February 18, 2018
Using BGP to Bind MPLS Labels to Address Prefixes
draft-ietf-mpls-rfc3107bis-04
Abstract
This document specifies a set of procedures for using BGP to
advertise that a specified router has bound a specified MPLS label
(or a specified sequence of MPLS labels, organized as a contiguous
part of a label stack) to a specified address prefix. This can be
done by sending a BGP UPDATE message whose Network Layer Reachability
Information field contains both the prefix and the MPLS label(s), and
whose Next Hop field identifies the node at which said prefix is
bound to said label(s). This document obsoletes RFC 3107.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on February 18, 2018.
Copyright Notice
Copyright (c) 2017 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
Rosen Expires February 18, 2018 [Page 1]
Internet-Draft BGP and Labeled Address Prefixes August 2017
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Using BGP to Bind an Address Prefix to One or More MPLS
Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1. Multiple Labels Capability . . . . . . . . . . . . . . . 5
2.2. NLRI Encoding when the Multiple Labels Capability is
Not Used . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3. NLRI Encoding when the Multiple Labels Capability is Used 10
2.4. How to Explicitly Withdraw the Binding of a Label to a
Prefix . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.5. Changing the Label that is Bound to a Prefix . . . . . . 12
3. Installing and/or Propagating SAFI-4 or SAFI-128 Routes . . . 13
3.1. Comparability of Routes . . . . . . . . . . . . . . . . . 13
3.2. Modification of Label(s) Field When Propagating . . . . . 14
3.2.1. When the Next Hop Field is Unchanged . . . . . . . . 14
3.2.2. When the Next Hop Field is Changed . . . . . . . . . 14
4. Data Plane . . . . . . . . . . . . . . . . . . . . . . . . . 15
5. Relationship Between SAFI-4 and SAFI-1 Routes . . . . . . . . 17
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 18
7. Security Considerations . . . . . . . . . . . . . . . . . . . 19
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 20
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 20
9.1. Normative References . . . . . . . . . . . . . . . . . . 20
9.2. Informative References . . . . . . . . . . . . . . . . . 22
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . 22
1. Introduction
[RFC3107] specifies encodings and procedures for using BGP to
indicate that a particular router has bound either a single MPLS
label or a sequence of MPLS labels (organized as a contiguous part of
an MPLS label stack) ([RFC3031], [RFC3032]) to a particular address
prefix. This is done by sending a BGP UPDATE message whose Network
Layer Reachability Information field contains both the prefix and the
MPLS label(s), and whose Next Hop field identifies the node at which
said prefix is bound to said label(s). Each such UPDATE also
advertises a path to the specified prefix, via the specified next
hop.
Although there are many implementations and deployments of [RFC3107],
there are a number of issues with [RFC3107] that have impeded
Rosen Expires February 18, 2018 [Page 2]
Internet-Draft BGP and Labeled Address Prefixes August 2017
interoperability in the past, and may potentially impede
interoperability in the future:
o Although [RFC3107] specifies an encoding that allows a sequence of
MPLS labels (rather than just a single label) to be bound to a
prefix, it does not specify the semantics of binding a sequence of
labels to a prefix.
o Many implementations of [RFC3107] assume that only one label will
be bound to a prefix, and cannot properly process a BGP UPDATE
message that binds a sequence of labels to a prefix. Thus an
implementation attempting to provide this feature is likely to
experience problems interoperating with other implementations.
o [RFC3107]'s procedures for withdrawing the binding of a label or
sequence of labels to a prefix are not specified clearly and
correctly.
o [RFC3107] specifies an optional feature, known as "Advertising
Multiple Routes to a Destination", that, to the best of the
author's knowledge, has never been implemented as specified. The
functionality that this feature was intended to provide can and
has been implemented in a different way using the procedures of
[RFC7911], which were not available at the time that [RFC3107] was
written. In [RFC3107], this feature was controlled by a BGP
Capability Code that has never been implemented, and is now
essentially obsolete.
o It is possible for a BGP speaker to receive two BGP UPDATEs that
advertise paths to the same address prefix, where one UPDATE binds
a label (or sequence of labels) to the prefix and the other does
not. [RFC3107] is silent on the issue of how the presence of two
such UPDATEs impacts the BGP decision process, and does not say
explicitly whether one or the other or both of these UPDATEs
should be propagated. This has led different implementations to
handle this situation in different ways.
o Much of [RFC3107] applies to the VPN-IPv4 ([RFC4364]) and VPN-IPv6
([RFC4659]) address families, but those address families are not
mentioned in [RFC3107].
This document replaces and obsoletes [RFC3107]. It defines a new BGP
Capability to be used when binding a sequence of labels to a prefix;
by using this Capability, the interoperability problems alluded to
above can be avoided. This document also removes the unimplemented
"Advertising Multiple Routes to a Destination" feature (see Section 4
of [RFC3107]), while specifying how to use [RFC7911] to provide the
same functionality. This document also addresses the issue of the
Rosen Expires February 18, 2018 [Page 3]
Internet-Draft BGP and Labeled Address Prefixes August 2017
how UPDATEs that bind labels to a given prefix interact with UPDATEs
that advertise paths to that prefix but do not bind labels to it.
However, for backwards compatibility, it declares most of these
interactions to be matters of local policy.
The places where this specification differs from [RFC3107] are
indicated in the text. It is believed that implementations that
conform to the current document will interoperate correctly with
existing deployed implementations of [RFC3107].
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
[RFC2119].
2. Using BGP to Bind an Address Prefix to One or More MPLS Labels
BGP may be used to advertise that a particular node, call it N, has
bound a particular MPLS label, or a particular sequence of MPLS
labels (organized as a contiguous part of an MPLS label stack), to a
particular address prefix. This is done by sending a Multiprotocol
BGP UPDATE message, i.e., an UPDATE message with an MP_REACH_NLRI
attribute ([RFC4760]). The "Network Address of Next Hop" field of
that attribute contains an IP address of node N. The label(s) and
the prefix are encoded in the NLRI field of the MP_REACH_NLRI. The
encoding of the NLRI field is specified in Sections 2.2 and 2.3.
If the prefix is an IPv4 address prefix or a VPN-IPv4 ([RFC4364])
address prefix, the Address Family Identifier (AFI) of the
MP_REACH_NLRI attribute is set to 1. If the prefix is an IPv6
address prefix or a VPN-IPv6 prefix ([RFC4659]), the AFI is set to 2.
If the prefix is an IPv4 address prefix or an IPv6 address prefix,
the Subsequent Address Family Identifier (SAFI) field is set to 4.
If the prefix is a VPN-IPv4 address prefix or a VPN-IPv6 address
prefix, the SAFI is set to 128.
The use of SAFI 4 or SAFI 128 when the AFI is other than 1 or 2 is
outside the scope of this document.
This document does not specify the format of the "Network Address of
Next Hop" field of the MP_REACH_NLRI attribute. The format of the
next hop field depends upon a number of factors, and is discussed in
a number of other RFCs: see [RFC4364], [RFC4659], [RFC4798], and
[RFC5549].
There are a variety of applications that make use of alternative
methods of using BGP to advertise MPLS label bindings. See, e.g.,
Rosen Expires February 18, 2018 [Page 4]
Internet-Draft BGP and Labeled Address Prefixes August 2017
[RFC7432], [RFC6514], or [TUNNEL-ENCAPS]. The method described in
the current document is not claimed to be the only way of using BGP
to advertise MPLS label bindings. Discussion of which method to use
for which application is outside the scope of the current document.
In the remainder of this document, we will use the term "SAFI-x
UPDATE" to refer to a BGP UPDATE message containing an MP_REACH_NLRI
attribute or an MP_UNREACH_NLRI attribute ([RFC4760]) whose SAFI
field contains the value x.
This document defines a BGP Optional Capabilities parameter
([RFC5492]) known as the "Multiple Labels Capability".
o Unless this Capability is sent on a given BGP session by both of
that session's BGP speakers, a SAFI-4 or SAFI-128 UPDATE message
sent on that session from either speaker MUST bind a prefix to
only a single label, and MUST use the encoding of Section 2.2.
o If this Capability is sent by both BGP speakers on a given
session, an UPDATE message on that session, from either speaker,
MUST use the encoding of Section 2.3, and MAY bind a prefix to a
sequence of more than one label.
The encoding of the Multiple Labels Capability is specified in
Section 2.1.
Procedures for explicitly withdrawing a label binding are given in
Section 2.4. Procedures for changing the label(s) bound to a given
prefix by a given node are given in Section 2.5.
Procedures for propagating SAFI-4 and SAFI-128 UPDATEs are discussed
in Section 3.
When a BGP speaker installs and propagates a SAFI-4 or SAFI-128
update, and if it changes the value of the Network Address of Next
Hop field, it must program its data plane appropriately. This is
discussed in Section 4.
2.1. Multiple Labels Capability
[RFC5492] defines the "Capabilities Optional Parameter". A BGP
speaker can include a Capabilities Optional Parameter in a BGP OPEN
message. The Capabilities Optional Parameter is a triple including a
one-octet Capability Code, a one-octet Capability length, and a
variable-length Capability Value.
This document defines a Capability Code, known as the "Multiple
Labels Capability" code. IANA will assign a codepoint for this
Rosen Expires February 18, 2018 [Page 5]
Internet-Draft BGP and Labeled Address Prefixes August 2017
Capability Code. (This Capability Code is new to this document and
does not appear in [RFC3107].)
If a BGP speaker has not sent the Multiple Labels Capability in its
BGP Open message on a particular BGP session, or if it has not
received the Multiple Labels Capability in the BGP Open message from
its peer on that BGP session, that BGP speaker MUST NOT send on that
session any UPDATE message that binds more than one MPLS label to any
given prefix. Further, when advertising the binding of a single
label to a prefix, the BGP speaker MUST use the encoding specified in
Section 2.2.
The value field of the Multiple Labels Capability (shown in Figure 1)
consists of one or more triples, where each triple consists of four
octets. The first two octets of a triple specify an AFI value, the
third octet specifies a SAFI value, and the fourth specifies a Count.
If one of the triples is <AFI,SAFI,Count>, the Count is the maximum
number of labels that the BGP speaker sending the Capability can
process in a received UPDATE of the specified AFI/SAFI. If the count
is 255, then no limit has been placed on the number of labels that
can be processed in a received UPDATE of the specified AFI/SAFI.
Any implementation that sends a Multiple Labels Capability MUST be
able to support at least two labels in the NLRI. However, there may
be deployment scenarios in which a larger number of labels is needed.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| AFI | SAFI | Count ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ AFI | SAFI | Count |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: Value Field of Multiple Labels Capability
If the Capability contains more than one triple with a given AFI/
SAFI, all but the first MUST be ignored.
A triple of the form <AFI=x,SAFI=y,Count=0> or <AFI=x,SAFI=y,Count=1>
MUST NOT be sent. If such a triple is received, it MUST be ignored.
A Multiple Labels Capability whose length is not a multiple of four
MUST be considered to be malformed.
[RFC4724] ("Graceful Restart Mechanism for BGP") describes a
procedure that allows routes learned over a given BGP session to be
maintained when the session fails and then restarts. This procedure
Rosen Expires February 18, 2018 [Page 6]
Internet-Draft BGP and Labeled Address Prefixes August 2017
requires the entire RIB to be transmitted when the session restarts.
If the Multiple Labels Capability for a given AFI/SAFI had been
exchanged on the failed session, but is not exchanged on the
restarted session, then any prefixes advertised in that AFI/SAFI with
multiple labels MUST be explicitly withdrawn. Similarly, if the
maximum label count, specified in the Capability for a given AFI/SAFI
is reduced, any prefixes advertised with more labels than are valid
for the current session MUST be explicitly withdrawn.
[Enhanced-GR] ("Accelerated Routing Convergence for BGP Graceful
Restart") describes another procedure that allows the routes learned
over a given BGP session to be maintained when the session fails and
then restarts. These procedures MUST NOT be applied if either of the
following conditions hold:
o The Multiple Labels Capability for a given AFI/SAFI had been
exchanged prior to the restart, but has not been exchanged on the
restarted session.
o The Multiple Labels Capability for a given AFI/SAFI had been
exchanged with a given Count prior to the restart, but has been
exchanged with a smaller count on the restarted session.
If either of these conditions hold, the complete set of routes for of
the given AFI/SAFI MUST be exchanged.
If a BGP OPEN message contains multiple copies of the Multiple Labels
Capability, only the first copy is significant; subsequent copies
MUST be ignored.
If a BGP speaker has sent the Multiple Labels Capability in its BGP
OPEN message for a particular BGP session, and has also received the
Multiple Labels Capability in its peer's BGP OPEN message for that
session, and if both Capabilities specify AFI/SAFI x/y, then:
when using an UPDATE of AFI x and SAFI y to advertise the binding
of a label or sequence of labels to a given prefix, the BGP
speaker MUST use the encoding of Section 2.3. This encoding MUST
be used even if only one label is being bound to a given prefix.
If both BGP speakers of a given BGP session have sent the Multiple
Labels Capability, but AFI/SAFI x/y has not been specified in both
Capabilities, then UPDATES of AFI/SAFI x/y on that session MUST use
the encoding of Section 2.2, and such UPDATEs can only bind one label
to a prefix.
A BGP speaker SHOULD NOT send an UPDATE that binds more labels to a
given prefix than its peer is capable of receiving, as specified in
Rosen Expires February 18, 2018 [Page 7]
Internet-Draft BGP and Labeled Address Prefixes August 2017
the Multiple Labels Capability sent by that peer. If a BGP speaker
receives an UPDATE that binds more labels to a given prefix than the
number of labels the BGP speaker is prepared to receive (as announced
in its Multiple Labels Capability), the BGP speaker MUST apply the
"treat-as-withdraw" strategy of [RFC7606] to that UPDATE.
Notwithstanding the number of labels that a BGP speaker has claimed
to be able to receive, its peer MUST NOT attempt to send more labels
than can be properly encoded in the NLRI field of the MP_REACH_NLRI
attribute. Please note that there is only a limited amount of space
in the NLRI field for labels:
o per [RFC4760] the size of this field is limited to 255 bits (not
255 octets), including the number of bits in the prefix;
o in a SAFI-128 update, the prefix is at least 64 bits long, and may
be as long as 192 bits (e.g., in a VPN-IPv6 host route).
2.2. NLRI Encoding when the Multiple Labels Capability is Not Used
If the Multiple Labels Capability has not been both sent and received
on a given BGP session, then in a BGP UPDATE on that session whose
MP_REACH_NLRI attribute contains one of the AFI/SAFI combinations
specified in Section 2, the NLRI field is encoded as shown in
Figure 2:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Length | Label |Rsrv |S|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Prefix ~
~ |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: NLRI With One Label
- Length:
The Length field consists of a single octet. It specifies the
length in bits of the remainder of the NLRI field.
Note that the length will always be the sum of 20 (number of bits
in label field) plus 3 (number of bits in Rsrv field) plus 1
(number of bits in S field) plus the length in bits of the prefix.
In an MP_REACH_NLRI attribute whose AFI/SAFI is 1/4, the prefix
length will be 32 bits or less. In an MP_REACH_NLRI attribute
Rosen Expires February 18, 2018 [Page 8]
Internet-Draft BGP and Labeled Address Prefixes August 2017
whose AFI/SAFI is 2/4, the prefix length will be 128 bits or less.
In an MP_REACH_NLRI attribute whose SAFI is 128, the prefix will
be 96 bits or less if the AFI is 1, and will be 192 bits or less
if the AFI is 2.
As specified in [RFC4760], the actual length of the NLRI field
will be the number of bits specified in the length field, rounded
up to the nearest integral number of octets.
- Label:
The Label field is a 20-bit field, containing an MPLS label value
(see [RFC3032]).
- Rsrv:
This 3-bit field SHOULD be set to zero on transmission, and MUST
be ignored on reception.
- S:
This 1-bit field MUST be set to one on transmission, and MUST be
ignored on reception.
Note that the UPDATE message not only advertises the binding between
the prefix and the label, it also advertises a path to the prefix via
the node identified in the "Network Address of Next Hop" field of the
MP_REACH_NLRI attribute.
[RFC3107] requires that if only a single label is bound to a prefix,
the S bit must be set. If the S bit is not set, [RFC3107] specifies
that additional labels will appear in the NLRI. However, some
implementations assume that the NLRI will contain only a single
label, and do not check the setting of the S bit. The procedures
specified in the current document will interwork with such
implementations. As long as the Multiple Labels Capability is not
sent and received by both BGP speakers on a given BGP session, this
document REQUIRES that only one label be specified in the NLRI, that
the S bit be set on transmission, and that it be ignored on
reception.
If the procedures of [RFC7911] are being used, a four-octet "path
identifier" (as defined in Section 3 of [RFC7911]) is part of the
NLRI, and precedes the Length field.
Rosen Expires February 18, 2018 [Page 9]
Internet-Draft BGP and Labeled Address Prefixes August 2017
2.3. NLRI Encoding when the Multiple Labels Capability is Used
If the Multiple Labels Capability has been both sent and received on
a given BGP session, then in a BGP UPDATE on that session whose
MP_REACH_NLRI attribute contains one of the AFI/SAFI combinations
specified in Section 2, the NLRI field is encoded as shown in
Figure 3:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+
| Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Label |Rsrv |S~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Label |Rsrv |S|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Prefix ~
~ |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: NLRI With Multiple Labels
- Length:
The Length field consists of a single octet. It specifies the
length in bits of the remainder of the NLRI field.
Note that for each label, the length is increased by 24 bits (20
bits in label field plus 3 bits in Rsrv field plus 1 S bit).
In an MP_REACH_NLRI attribute whose AFI/SAFI is 1/4, the prefix
length will be 32 bits or less. In an MP_REACH_NLRI attribute
whose AFI/SAFI is 2/4, the prefix length will be 128 bits or less.
In an MP_REACH_NLRI attribute whose SAFI is 128, the prefix will
be 96 bits or less if the AFI is 1, and will be 192 bits or less
if the AFI is 2.
As specified in [RFC4760], the actual length of the NLRI field
will be the number of bits specified in the length field, rounded
up to the nearest integral number of octets.
- Label:
The Label field is a 20-bit field, containing an MPLS label value
([RFC3032]).
- Rsrv:
Rosen Expires February 18, 2018 [Page 10]
Internet-Draft BGP and Labeled Address Prefixes August 2017
This 3-bit field SHOULD be set to zero on transmission, and MUST
be ignored on reception.
- S:
In all labels except the last (i.e., in all labels except the one
immediately preceding the prefix), the S bit MUST be 0. In the
last label, the S bit MUST be 1.
Note that failure to set the S bit in the last label will make it
impossible to parse the NLRI correctly. See Section 3 paragraph j
of [RFC7606] for a discussion of error handling when the NLRI
cannot be parsed.
Note that the UPDATE message not only advertises the binding between
the prefix and the labels, it also advertises a path to the prefix
via the node identified in the "next hop" field of the MP_REACH_NLRI
attribute.
If the procedures of [RFC7911] are being used, a four-octet "path
identifier" (as defined in Section 3 of [RFC7911]) is part of the
NLRI, and precedes the Length field.
2.4. How to Explicitly Withdraw the Binding of a Label to a Prefix
Suppose a BGP speaker has announced, on a given BGP session, the
binding of a given label or sequence of labels to a given prefix.
Suppose it now wishes to withdraw that binding. To do so, it may
send a BGP UPDATE message with an MP_UNREACH_NLRI attribute. The
NLRI field of this attribute is encoded as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Length | Compatibility |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Prefix ~
~ |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4: NLRI For Withdrawal
Upon transmission, the Compatibility field SHOULD be set to 0x800000.
Upon reception, the value of the Compatibility field MUST be ignored.
This encoding is used for explicitly withdrawing the binding, on a
given BGP session, between the specified prefix and whatever label or
sequence of labels had previously been bound by the procedures of
Rosen Expires February 18, 2018 [Page 11]
Internet-Draft BGP and Labeled Address Prefixes August 2017
this document to that prefix on the given session. This encoding is
used whether or not the Multiple Labels Capability has been sent or
received on the session. Note that label/prefix bindings that were
not advertised on the given session cannot be withdrawn by this
method. (However, if the bindings were advertised on a previous
session with the same peer, and the current session is the result of
a "graceful restart" ([RFC4724]) of the previous session, then this
withdrawal method may be used.)
When using an MP_UNREACH_NLRI attribute to withdraw a route whose
NLRI was previously specified in an MP_REACH_NLRI attribute, the
lengths and values of the respective prefixes must match, and the
respective AFI/SAFIs must match. If the procedures of [RFC7911] are
being used, the respective values of the "path identifier" fields
must match as well. Note that the prefix length is not the same as
the NLRI length; to determine the prefix length of a prefix in an
MP_UNREACH_NLRI, the length of the Compatibility field must be
subtracted from the length of the NLRI.
An explicit withdrawal in a SAFI-x UPDATE on a given BGP session not
only withdraws the binding between the prefix and the label(s), it
also withdraws the path to that prefix that was previously advertised
in a SAFI-x UPDATE on that session.
[RFC3107] allowed one to specify a particular label value in the
Compatibility field. However, the functionality that required the
presence of a particular label value (or sequence of label values)
was never implemented, and that functionality is not present in the
current document. Hence the value of this field is of no
significance; there is never any reason for this field to contain a
label value or a sequence of label values.
[RFC3107] also allowed one to withdraw a binding without specifying
the label explicitly, by setting the Compatibility field to 0x800000.
However, some implementations set it to 0x000000. In order to ensure
backwards compatibility, it is RECOMMENDED by this document that the
Compatibility field be set to 0x800000, but it is REQUIRED that it be
ignored upon reception.
2.5. Changing the Label that is Bound to a Prefix
Suppose a BGP speaker, S1, has received on a given BGP session, a
SAFI-4 or SAFI-128 UPDATE, U1, that specifies label (or sequence of
labels) L1, prefix P, and next hop N1. As specified above, this
indicates that label (or sequence of labels) L1 is bound to prefix P
at node N1. Suppose that S1 now receives, on the same session, an
UPDATE, U2, of the same AFI/SAFI, that specifies label (or sequence
of labels) L2, prefix P, and the same next hop, N1.
Rosen Expires February 18, 2018 [Page 12]
Internet-Draft BGP and Labeled Address Prefixes August 2017
o If [RFC7911] is not being used, UPDATE U2 MUST be interpreted as
meaning that L2 is now bound to P at N1, and that L1 is no longer
bound to P at N1. That is, the UPDATE U1 is implicitly withdrawn,
and is replaced by UPDATE U2.
o Suppose that [RFC7911] is being used, that UPDATE U1 has Path
Identifier I1, and that UPDATE U2 has Path Identifier I2.
* If I1 is the same as I2, UPDATE U2 MUST be interpreted as
meaning that L2 is now bound to P at N1, and that L1 is no
longer bound to P at N1. UPDATE U1 is implicitly withdrawn.
* If I1 is not the same as I2, U2 MUST be interpreted as meaning
that L2 is now bound to P at N1, but MUST NOT be interpreted as
meaning that L1 is no longer bound to P at N1. Under certain
conditions (specification of which is outside the scope of this
document), S1 may choose to load-balance traffic between the
path represented by U1 and the path represented by U2. To send
traffic on the path represented by U1, S1 uses the label(s)
advertised in U1; to send traffic on the path represented by
U2, S1 uses the label(s) advertised in U2. (Although these two
paths have the same next hop, one must suppose that they
diverge further downstream.)
Suppose a BGP speaker, S1, has received, on a given BGP session, a
SAFI-4 or SAFI-128 UPDATE that specifies label L1, prefix P, and next
hop N1. Suppose that S1 now receives, on a different BGP session, an
UPDATE, of the same AFI/SAFI, that specifies label L2, prefix P, and
the same next hop, N1. BGP speaker S1 SHOULD treat this as
indicating that N1 has at least two paths to P, and S1 MAY use this
fact to do load-balancing of any traffic that it has to send to P.
Note that this section discusses only the case where two UPDATEs have
the same next hop. Procedures for the case where two UPDATEs have
different next hops are adequately described in [RFC4271].
3. Installing and/or Propagating SAFI-4 or SAFI-128 Routes
3.1. Comparability of Routes
Suppose a BGP speaker has received two SAFI-4 UPDATEs specifying the
same Prefix, and that either:
o the two UPDATEs are received on different BGP sessions, or
o the two UPDATES are received on the same session, add-paths is
used on that session, and the NLRIs of the two updates have
different path identifiers.
Rosen Expires February 18, 2018 [Page 13]
Internet-Draft BGP and Labeled Address Prefixes August 2017
These two routes MUST be considered to be comparable, even if they
specify different labels. Thus the BGP bestpath selection procedures
(Section 9.1 of [RFC4271]) are applied to select one of them as the
better path. If the procedures of [RFC7911] are not being used on a
particular BGP session, only the best path is propagated on that
session. If the procedures of [RFC7911] are being used on a
particular BGP session, then both paths may be propagated on that
session, though with different path identifiers.
The same applies to SAFI-128 routes.
3.2. Modification of Label(s) Field When Propagating
3.2.1. When the Next Hop Field is Unchanged
When a SAFI-4 or SAFI-128 route is propagated, if the "Network
Address of Next Hop" field is left unchanged, the label field(s) MUST
also be left unchanged.
Note that a given route MUST NOT be propagated to a given peer if the
route's NLRI has multiple labels, but the "Multiple Labels"
Capability was not negotiated with the peer. Similarly, a given
route MUST NOT be propagated to a given peer if the route's NLRI has
more labels than the peer has announced (through its "Multiple
Labels" Capability) that it can handle. In either case, if a
previous route with the same AFI, SAFI, and prefix (but with fewer
labels) has already been propagated to the peer, that route MUST be
withdrawn from that peer, using the procedure of Section 2.4.
3.2.2. When the Next Hop Field is Changed
If the "Network Address of Next Hop" field is changed before a SAFI-4
or SAFI-128 route is propagated, the label field(s) of the propagated
route MUST contain the label(s) that that is (are) bound to the
prefix at the new next hop.
Suppose BGP speaker S1 has received an UPDATE that binds a particular
sequence of one or more labels to a particular prefix. If S1 chooses
to propagate this route after changing its next hop, S1 may change
the label in any of the following ways, depending upon local policy:
o A single label may be replaced by a single label, of the same or
different value.
o A sequence of multiple labels may be replaced by a single label.
o A single label may be replaced by a sequence of multiple labels.
Rosen Expires February 18, 2018 [Page 14]
Internet-Draft BGP and Labeled Address Prefixes August 2017
o A sequence of multiple labels may be replaced by a sequence of
multiple labels; the number of labels may be left the same, or may
be changed.
Of course, when deciding whether to propagate, to a given BGP peer,
an UPDATE binding a sequence of more than one label, a BGP speaker
must attend to the information provided by the Multiple Labels
Capability (see Section 2.1). A BGP speaker MUST NOT send multiple
labels to a peer with which it has not exchanged the "Multiple
Labels" Capability, and MUST NOT send more labels to a given peer
than the peer has announced (via the "Multiple Labels" Capability)
than it can handle.
It is possible that a BGP speaker's local policy will tell it to
encode N labels in a given route's NLRI before propagating the route,
but that one of the BGP speaker's peers cannot handle N labels in the
NLRI. In this case, the BGP speaker has two choices:
o It can propagate the route to the given peer with fewer than N
labels. However, whether this makes sense, and if so, how to
choose the labels, is also a matter of local policy.
o It can decide not to propagate the route to the given peer. In
that case, if a previous route with the same AFI, SAFI, and prefix
(but with fewer labels) has already been propagated to that peer,
that route MUST be withdrawn from that peer, using the procedure
of Section 2.4.
4. Data Plane
In the following, we will use the phrase "node S tunnels packet P to
node N", where packet P is an MPLS packet. By this phrase, we mean
that node S encapsulates packet P and causes packet P to be delivered
to node N, in such a way that P's label stack before encapsulation
will be seen unchanged by N, but will not be seen by the nodes (if
any) between S and N.
If the tunnel is a Label Switched Path (LSP), encapsulating the
packet may be as simple as pushing on another MPLS label. If node N
is a layer 2 adjacency of node S, a layer 2 encapsulation may be all
that is needed. Other sorts of tunnels (e.g., IP tunnels, GRE
tunnels, UDP tunnels) may also be used, depending upon the particular
deployment scenario.
Suppose BGP speaker S1 receives a SAFI-4 or SAFI-128 BGP UPDATE with
an MP_REACH_NLRI specifying label L1, prefix P, and next hop N1, and
suppose S1 installs this route as its (or one of its) bestpath(s)
towards P. And suppose S1 propagates this route after changing the
Rosen Expires February 18, 2018 [Page 15]
Internet-Draft BGP and Labeled Address Prefixes August 2017
next hop to itself and changing the label to L2. Suppose further
that S1 receives an MPLS data packet, and in the process of
forwarding that MPLS data packet, S1 sees label L2 rise to the top of
the packet's label stack. Then to forward the packet further, S1
must replace L2 with L1 as the top entry in the packet's label stack,
and S1 must then tunnel the packet to N1.
Suppose that the route received by S1 specified not a single label,
but a sequence of k labels <L11, L12, ..., L1k>, where L11 is the
first label appearing in the NLRI, and L1k is the last. And suppose
again that S1 propagates this route after changing the next hop to
itself and changing the label field to the single label L2. Suppose
further that S1 receives an MPLS data packet, and in the process of
forwarding that MPLS data packet, S1 sees label L2 rise to the top of
the packet's label stack. In this case, instead of simply replacing
L2 with L1, S1 removes L2 from the top of the label stack, and then
pushes labels L1k through L11 onto the label stack, such that L11 is
now at the top of the label stack. Then S1 must tunnel the packet to
N1. (Note that L1k will not be at the bottom of the packet's label
stack, and hence will not have the "bottom of stack" bit set, unless
L2 had previously been at the bottom of the packet's label stack.)
The above paragraph assumes that when S1 propagates a SAFI-4 or
SAFI-128 route after setting the next hop to itself, it replaces the
label or labels specified in the NLRI of that route with a single
label. However, it is also possible, as determined by local policy,
for a BGP speaker to specify multiple labels when it propagates a
SAFI-4 or SAFI-128 route after setting the next hop to itself.
Suppose, for example, that S1 supports context labels ([RFC5331]).
Let L21 be a context label supported by S1, and let L22 be a label
that is in the label space identified (at S1) by L21. Suppose S1
receives a SAFI-4 or SAFI-128 UPDATE whose prefix is P, whose label
field is <L11,L12,...L1k>, and whose next hop is N1. Before
propagating the UPDATE, S1 may set the next hop to itself (by
replacing N1 with S1), and may replace the label stack
<L11,L12,...L1k> with the pair of labels <L21,L22>.
In this case, if S1 receives an MPLS data packet whose top label is
L21 and whose second label is L22, S1 will remove both L21 and L22
from the label stack, and replace them with <L11,L12,...L1k>. Note
that the fact that L21 is a context label is known only to S1; other
BGP speakers do not know how S1 will interpret L21 (or L22).
The ability to replace one or more labels by one or more labels can
provide great flexibility, but must be done carefully. Let's suppose
again that S1 receives an UPDATE that specifies prefix P, label stack
<L11,L12,...,L1k>, and next hop N1. And suppose that S1 propagates
Rosen Expires February 18, 2018 [Page 16]
Internet-Draft BGP and Labeled Address Prefixes August 2017
this UPDATE to BGP speaker S2 after setting next hop self and after
replacing the label field with <L21,L22,...L2k>. Finally, suppose
that S1 programs its data plane so that when it processes a received
MPLS packet whose top label is L21, it replaces L21 with
<L11,L12,...,L1k>, and then tunnels the packet to N1.
In this case, BGP speaker S2 will have received a route with prefix
P, label field <L21,L22,...L2k>, and next hop S1. If S2 decides to
forward an IP packet according to this route, it will push
<L21,L22,...L2k> onto the packet's label stack, and tunnel the packet
to S1. S1 will replace L21 with <L11,L12,...,L1k>, and will tunnel
the packet to N1. N1 will receive the packet with the following
label stack: <L11,L12,...L1k,L22,...L2k>. While this may be useful
in certain scenarios, it may provide unintended results in other
scenarios.
Procedures for choosing, setting up, maintaining, or determining the
liveness of a particular tunnel or type of tunnel, are outside the
scope of this document.
When pushing labels onto a packet's label stack, the Time-to-Live
(TTL) field ([RFC3032], [RFC3443]) and the Traffic Class (TC) field
([RFC3032], [RFC5462]) of each label stack entry must of course be
set. This document does not specify any set of rules for setting
these fields; that is a matter of local policy.
This document does not specify any new rules for processing the label
stack of an incoming data packet.
It is a matter of local policy whether SAFI-4 routes can be used as
the basis for forwarding IP packets, or whether SAFI-4 routes can
only be used for forwarding MPLS packets. If BGP speaker S1 is
forwarding IP packets according to SAFI-4 routes, then consider an IP
packet with destination address D, such that P is the "longest prefix
match" for D from among the routes that are being used to forward IP
packets. And suppose the packet is being forwarded according to a
SAFI-4 route whose prefix is P, whose next hop is N1, and whose
sequence of labels is L1. To forward the packet according to this
route, S1 must create a label stack for the packet, push on the
sequence of labels L1, and then tunnel the packet to N1.
5. Relationship Between SAFI-4 and SAFI-1 Routes
It is possible that a BGP speaker will receive both a SAFI-1 route
for prefix P and a SAFI-4 route for prefix P. Different
implementations treat this situation in different ways.
Rosen Expires February 18, 2018 [Page 17]
Internet-Draft BGP and Labeled Address Prefixes August 2017
For example, some implementations may regard SAFI-1 routes and SAFI-4
routes as completely independent, and may treat them in a "ships in
the night" fashion. In this case, bestpath selection for the two
SAFIs is independent, and there will be a best SAFI-1 route to P as
well as a best SAFI-4 route to P. Which packets get forwarded
according to the routes of which SAFI is then a matter of local
policy.
Other implementations may treat the SAFI-1 and SAFI-4 routes for a
given prefix as comparable, such that the best route to prefix P is
either a SAFI-1 route or a SAFI-4 route, but not both. In such
implementations, if load-balancing is done among a set of equal cost
routes, some of the equal cost routes may be SAFI-1 routes and some
may be SAFI-4 routes. Whether this is allowed is again a matter of
local policy.
Some implementations may allow a single BGP session to carry UPDATES
of both SAFI-1 and SAFI-4; other implementations may disallow this.
Some implementations that allow both SAFIs on the same session may
treat the receipt of a SAFI-1 route for prefix P on a given session
as an implicit withdrawal of a previous SAFI-4 route for prefix P on
that session, and vice versa. Other implementations may have
different behavior.
A BGP speaker may receive a SAFI-4 route over a given BGP session,
but may have other BGP sessions for which SAFI-4 is not enabled. In
this case, the BGP speaker MAY convert the SAFI-4 route to a SAFI-1
route and then propagate the result over the session on which SAFI-4
is not enabled. Whether this is done is a matter of local policy.
These differences in the behavior of different implementations may
result in unexpected behavior or lack of interoperability. In some
cases, it may be difficult or impossible to achieve the desired
policies with certain implementations or combinations of
implementations.
6. IANA Considerations
IANA is requested to assign a codepoint for "Multiple Labels
Capability" in the "BGP Capability Codes" registry, with this
document as the reference.
IANA is requested to modify the "BGP Capability Codes" registry to
mark Capability Code 4 ("Multiple routes to a destination") as
deprecated, with this document as the reference.
IANA is requested to change the reference for SAFI 4 in the
"Subsequent Address Family Identifiers (SAFI) Parameters" to this
Rosen Expires February 18, 2018 [Page 18]
Internet-Draft BGP and Labeled Address Prefixes August 2017
document. IANA is also requested to add this document as a reference
for SAFI 128 in that same registry.
7. Security Considerations
The security considerations of the BGP specification ([RFC4271])
apply.
If a BGP implementation, not conformant with the current document,
encodes multiple labels in the NLRI but has not sent and received the
"Multiple Labels" Capability, a BGP implementation that does conform
with the current document will likely reset the BGP session.
This document specifies that certain data packets be "tunneled" from
one BGP speaker to another. This requires that the packets be
encapsulated while in flight. This document does not specify the
encapsulation to be used. However, if a particular encapsulation is
used, the security considerations of that encapsulation are
applicable.
If a particular tunnel encapsulation does not provide integrity and
authentication, it is possible that a data packet's label stack can
be modified, through error or malfeasance, while the packet is in
flight. This can result in misdelivery of the packet. It should be
noted that the tunnel encapsulation (MPLS) most commonly used in
deployments of this specification does not provide integrity or
authentication; neither do the other tunnel encapsulations mentioned
in Section 4.
There are various techniques one can use to constrain the
distribution of BGP UPDATE messages. If a BGP UPDATE advertises the
binding of a particular (set of) label(s) to a particular address
prefix, such techniques can be used to control the set of BGP
speakers that are intended to learn of that binding. However, if BGP
sessions do not provide privacy, other routers may learn of that
binding.
When a BGP speaker processes a received MPLS data packet whose top
label it advertised, there is no guarantee that the label in question
was put on the packet by a router that was intended to know about
that label binding. If a BGP speaker is using the procedures of this
document, it may be useful for that speaker to distinguish its
"internal" interfaces from its "external" interfaces, and to avoid
advertising the same labels to BGP speakers reached on internal
interfaces as to BGP speakers reached on external interfaces. Then a
data packet can be discarded if its top label was not advertised over
the type of interface from which the packet was received. This
Rosen Expires February 18, 2018 [Page 19]
Internet-Draft BGP and Labeled Address Prefixes August 2017
reduces the likelihood of forwarding packets whose labels have been
"spoofed" by untrusted sources.
8. Acknowledgements
This draft obsoletes RFC 3107. We wish to thank Yakov Rekhter, co-
author of RFC 3107, for his work on that document. We also wish to
thank Ravi Chandra, Enke Chen, Srihari R. Sangli, Eric Gray, and
Liam Casey for their review of and comments on that document.
We thank Alexander Okonnikov and David Lamparter for pointing out a
number of the errors in RFC 3107.
We wish to thank Lili Wang and Kaliraj Vairavakkalai for their help
and advice during the preparation of this document.
We also thank Mach Chen, Bruno Decraene, Jie Dong, Adrian Farrel,
Jeff Haas, Jonathan Hardwick, Jakob Heitz, Alexander Okonnikov, Keyur
Patel, Kevin Wang, and Lucy Yong for their review of and comments on
this document.
9. References
9.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997, <https://www.rfc-
editor.org/info/rfc2119>.
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon, "Multiprotocol
Label Switching Architecture", RFC 3031,
DOI 10.17487/RFC3031, January 2001, <https://www.rfc-
editor.org/info/rfc3031>.
[RFC3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y.,
Farinacci, D., Li, T., and A. Conta, "MPLS Label Stack
Encoding", RFC 3032, DOI 10.17487/RFC3032, January 2001,
<https://www.rfc-editor.org/info/rfc3032>.
[RFC3107] Rekhter, Y. and E. Rosen, "Carrying Label Information in
BGP-4", RFC 3107, DOI 10.17487/RFC3107, May 2001,
<https://www.rfc-editor.org/info/rfc3107>.
[RFC3443] Agarwal, P. and B. Akyol, "Time To Live (TTL) Processing
in Multi-Protocol Label Switching (MPLS) Networks",
RFC 3443, DOI 10.17487/RFC3443, January 2003,
<https://www.rfc-editor.org/info/rfc3443>.
Rosen Expires February 18, 2018 [Page 20]
Internet-Draft BGP and Labeled Address Prefixes August 2017
[RFC4271] Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A
Border Gateway Protocol 4 (BGP-4)", RFC 4271,
DOI 10.17487/RFC4271, January 2006, <https://www.rfc-
editor.org/info/rfc4271>.
[RFC4364] Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private
Networks (VPNs)", RFC 4364, DOI 10.17487/RFC4364, February
2006, <https://www.rfc-editor.org/info/rfc4364>.
[RFC4659] De Clercq, J., Ooms, D., Carugi, M., and F. Le Faucheur,
"BGP-MPLS IP Virtual Private Network (VPN) Extension for
IPv6 VPN", RFC 4659, DOI 10.17487/RFC4659, September 2006,
<https://www.rfc-editor.org/info/rfc4659>.
[RFC4760] Bates, T., Chandra, R., Katz, D., and Y. Rekhter,
"Multiprotocol Extensions for BGP-4", RFC 4760,
DOI 10.17487/RFC4760, January 2007, <https://www.rfc-
editor.org/info/rfc4760>.
[RFC4798] De Clercq, J., Ooms, D., Prevost, S., and F. Le Faucheur,
"Connecting IPv6 Islands over IPv4 MPLS Using IPv6
Provider Edge Routers (6PE)", RFC 4798,
DOI 10.17487/RFC4798, February 2007, <https://www.rfc-
editor.org/info/rfc4798>.
[RFC5462] Andersson, L. and R. Asati, "Multiprotocol Label Switching
(MPLS) Label Stack Entry: "EXP" Field Renamed to "Traffic
Class" Field", RFC 5462, DOI 10.17487/RFC5462, February
2009, <https://www.rfc-editor.org/info/rfc5462>.
[RFC5492] Scudder, J. and R. Chandra, "Capabilities Advertisement
with BGP-4", RFC 5492, DOI 10.17487/RFC5492, February
2009, <https://www.rfc-editor.org/info/rfc5492>.
[RFC5549] Le Faucheur, F. and E. Rosen, "Advertising IPv4 Network
Layer Reachability Information with an IPv6 Next Hop",
RFC 5549, DOI 10.17487/RFC5549, May 2009,
<https://www.rfc-editor.org/info/rfc5549>.
[RFC7606] Chen, E., Ed., Scudder, J., Ed., Mohapatra, P., and K.
Patel, "Revised Error Handling for BGP UPDATE Messages",
RFC 7606, DOI 10.17487/RFC7606, August 2015,
<https://www.rfc-editor.org/info/rfc7606>.
Rosen Expires February 18, 2018 [Page 21]
Internet-Draft BGP and Labeled Address Prefixes August 2017
9.2. Informative References
[Enhanced-GR]
Patel, K., Chen, E., Fernando, R., and J. Scudder,
"Accelerated Routing Convergence for BGP Graceful
Restart", internet-draft draft-ietf-idr-enhanced-gr-06,
June 2016.
[RFC4724] Sangli, S., Chen, E., Fernando, R., Scudder, J., and Y.
Rekhter, "Graceful Restart Mechanism for BGP", RFC 4724,
DOI 10.17487/RFC4724, January 2007, <https://www.rfc-
editor.org/info/rfc4724>.
[RFC5331] Aggarwal, R., Rekhter, Y., and E. Rosen, "MPLS Upstream
Label Assignment and Context-Specific Label Space",
RFC 5331, DOI 10.17487/RFC5331, August 2008,
<https://www.rfc-editor.org/info/rfc5331>.
[RFC6514] Aggarwal, R., Rosen, E., Morin, T., and Y. Rekhter, "BGP
Encodings and Procedures for Multicast in MPLS/BGP IP
VPNs", RFC 6514, DOI 10.17487/RFC6514, February 2012,
<https://www.rfc-editor.org/info/rfc6514>.
[RFC7432] Sajassi, A., Ed., Aggarwal, R., Bitar, N., Isaac, A.,
Uttaro, J., Drake, J., and W. Henderickx, "BGP MPLS-Based
Ethernet VPN", RFC 7432, DOI 10.17487/RFC7432, February
2015, <https://www.rfc-editor.org/info/rfc7432>.
[RFC7911] Walton, D., Retana, A., Chen, E., and J. Scudder,
"Advertisement of Multiple Paths in BGP", RFC 7911,
DOI 10.17487/RFC7911, July 2016, <https://www.rfc-
editor.org/info/rfc7911>.
[TUNNEL-ENCAPS]
Rosen, E., Patel, K., and G. Vandevelde, "The BGP Tunnel
Encapulation Attribute", internet-draft draft-ietf-idr-
tunnel-encaps-07, July 2017.
Author's Address
Eric C. Rosen
Juniper Networks, Inc.
10 Technology Park Drive
Westford, Massachusetts 01886
United States
Email: erosen@juniper.net
Rosen Expires February 18, 2018 [Page 22]
