Internet DRAFT - draft-ietf-ntp-implementation-guidance
draft-ietf-ntp-implementation-guidance
NTP Working Group A. Malhotra
Internet-Draft Boston University
Intended status: Informational K. Teichel
Expires: May 22, 2020 PTB
M. Hoffmann
W. Toorop
NLnet Labs
November 19, 2019
On Implementing Time
draft-ietf-ntp-implementation-guidance-00
Abstract
This document describes the properties of different types of clocks
available on digital systems. It provides implementors of
applications with guidance on choices they have to make when working
with time to provide basic functionality and security guarantees.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on May 22, 2020.
Copyright Notice
Copyright (c) 2019 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
Malhotra, et al. Expires May 22, 2020 [Page 1]
Internet-Draft implementation-advice November 2019
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Scope of the document . . . . . . . . . . . . . . . . . . . . 3
3. Expressing Time . . . . . . . . . . . . . . . . . . . . . . . 3
3.1. Absolute Time . . . . . . . . . . . . . . . . . . . . . . 4
3.2. Relative Time . . . . . . . . . . . . . . . . . . . . . . 4
4. Keeping Time: Different Clocks . . . . . . . . . . . . . . . 4
4.1. Native Clock . . . . . . . . . . . . . . . . . . . . . . 4
4.2. World Clock . . . . . . . . . . . . . . . . . . . . . . . 5
5. Implementation Approaches . . . . . . . . . . . . . . . . . . 6
6. Accessing the Native Clock on Selected Operating Systems . . 7
6.1. POSIX . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6.2. Microsoft Window . . . . . . . . . . . . . . . . . . . . 7
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 7
8. Security Considerations . . . . . . . . . . . . . . . . . . . 7
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 8
9.1. Normative References . . . . . . . . . . . . . . . . . . 8
9.2. Informative References . . . . . . . . . . . . . . . . . 8
Appendix A. Acknowledgements . . . . . . . . . . . . . . . . . . 8
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 8
1. Introduction
It is hard to overstate the importance of time in modern digital
systems. The functionality and security of applications (distributed
or local to one system) and that of network protocols generally hinge
on some notion of time. For implementation, these applications and
protocols have to choose one of the types of clocks available on
their system, each of which has its own specific properties.
However, currently many of these applications seem to be oblivious to
the implications of choosing one or the other clock for
implementation. This behavior can be attributed to:
a. the lack of clear understanding of the distinct properties of
these clocks,
b. trade-offs of using one or the other for an application, and
c. availability and compatibility of these clocks on different
systems.
This document discusses a) and b).
Malhotra, et al. Expires May 22, 2020 [Page 2]
Internet-Draft implementation-advice November 2019
More specifically, in this document we first define different methods
used by protocols and applications to express time. We then define
properties of clocks maintained by modern digital systems. Next we
describe how systems obtain these values from these clocks and the
security considerations of using these values to implement protocols
and applications that use time. Finally we discuss trade-offs
between security and precision of choosing a clock. The document
aims to provide guidance to the implementors make an informed choice
with an example of POSIX system.
2. Scope of the document
This document aims to provide software developers implementing
protocols and applications that have to deal with time with the
knowledge and understanding to make informed decisions regarding the
available clocks and their respective trade-offs.
It does not describe functionality that is specific to the
architecture of a PC, or other devices such as phones, IoT devices,
switches, routers, base stations, or synchrophasors. Nor is the
document applicable to a specific operating system. Throughout the
document we assume that one or the other clock is available on most
devices. How these clocks are available on different PCs or other
devices is out of scope of this document.
We do not exactly recommend which clock should be used. We discuss
the available options and trade-offs. The final decision would vary
depending on the availability of clocks and the security requirements
of the specific application under implementation.
Note: Since there is a lack of standards on terminology related to
time, we define some terms in the following section. Also,
throughout the document, we define the terms as they become relevant.
Different systems, depending on their OS, may use different terms for
the same types of clocks. A survey on this is not in the scope of
this document. We provide a discussion on how to access these values
on POSIX and Windows systems. On other systems, implementors will
have to determine themselves which of these values are available.
3. Expressing Time
Protocols and applications can express time in several forms,
depending on whether they need to express a point in time or a time
interval.
Malhotra, et al. Expires May 22, 2020 [Page 3]
Internet-Draft implementation-advice November 2019
3.1. Absolute Time
Absolute time expresses a universally agreed upon reference to a
specific point in time. Such a reference can be expressed in
different ways. For instance, Unix Time refers to the number of
seconds since midnight UTC, January 1st, 1970, while in everyday
life, we referenced such a point through year, month, day, and so on.
Because absolute time expresses a shared view of time, a system needs
to synchronize its clock with a common reference clock, for instance
one base on UTC.
Absolute time is often used to express the start or end of the
validity of objects with a limited lifetime that are shared over the
network.
3.2. Relative Time
Relative time measures the time interval that has elapsed from some
well-defined reference point (e.g., 20 minutes from the time of your
query).
Relative time is commonly used in network protocols, for instance to
determine when a packet should be considered dropped or to express
Time To Live (TTL) values that govern the length of time for which an
object is valid or usable.
Since relative time does not express a point in time, it does not
rely on synchronized clocks between systems but only on a shared
clock rate.
4. Keeping Time: Different Clocks
In this section, we will have a look at the different clocks a system
uses and how it maintains these clocks
4.1. Native Clock
Each system has its own perception of time. It gains access it via
its native clock. Typcially, this clock counts cycles of an
oscillator but some systems use process CPU times or thread CPU
timers (via timers provided by the CPU). The quality of the native
clock therefore dependends on either the stability of the oscillator
or the CPU timer.
The timescale of the native clock is a purely subjective -- no
general meaning can be attached to any specific clock value. One can
only obtain relative time by comparing two values. Because the value
Malhotra, et al. Expires May 22, 2020 [Page 4]
Internet-Draft implementation-advice November 2019
of the native clock always grows at a steady pace, never decreases,
never make unexpected jumps, and never skips, the difference between
two clock values provides the time intervall between the two
measurements.
The independence of the native clock from any external time sources
renders it resistant to any manipulation but in return there is no
guarantee that its clock rate is similar to that of any other system.
This difference in rate, especially when compared to a reference
clock, is called clock drift.
Clock drift depends on the quality of the clock itself but also on
factors such as system load or ambient temperatur which makes it hard
to predict.
4.2. World Clock
The native clock only provides means to measure relative time. In
order to be able to also process absolute time, it needs to be
synchronized with a global reference clock. Since this clock strives
to be the same on all systems, we call it the world clock.
There are a number of ways to maintain the world clock based on the
system's native clock.
o The first is to manually maintain an offset between values of the
native clock and the reference world clock. Because of the clock
drift of the native clock, this offset needs to be updated from
time to time if a minimal divergence from the reference clock is
to be maintained.
o Secondly, a hardware clock provided by the system and set to be
equivalent to the reference time can be used, allowing the system
to retain the offset across reboots.
o Finally, the reference clock can be obtained from an external time
source. Typically, the Internet is used through a variety of
timing protocols including the Network Time Protocol2 (NTP),
Chrony, SNTP, OpenNTP and others.
Each of these approaches has own problems attached to it.
o Manual configurations can be subject to errors and
misconfiguration.
o Accessing the hardware clock requires an I/O operation which is
resource intensive, therefore many systems use the hardware clock
Malhotra, et al. Expires May 22, 2020 [Page 5]
Internet-Draft implementation-advice November 2019
only upon reboot, to initialize the clock offset; subsequent
updates are made either manually or through timing protocols.
Further, on many systems the quality of the hardware clock isn't
very high, leading to a large clock drift if solely relying on it.
Worse, systems like microcontrollers that operate within embedded
systems (e.g., Raspberry Pi, Arduino, etc.) often lack hardware
clocks altogether. These systems rely on external time sources
upon reboot and have no means to process absolute time until
synchronization with these sources has completed.
o Relying on Internet timing protocols opens up the system time to
attack. Recent papers show vulnerabilities in NTP
[ANTP][ANABM][SECNTP] and SNTP [BPHSTS] that allow attackers to
maliciously alter system's world clock -- pushing it into the past
or even into the future. Moreover, many of these time-shifting
attacks can be performed by off-path attackers, who do not occupy
a privileged position on the network between the victim system and
its time sources on the Internet. Researchers have also
demonstrated off-path denial of service attacks on timing
protocols that prevent systems from synchronizing their clocks.
In other words, the process of obtaining the offset necessary to
provide a world clock creates dependencies that can be exploited.
5. Implementation Approaches
Because absolute time relies on a shared interpretation of a value
expressing time, the world clock is necessary when processing such
values.
For relative time, however, where only the rate of passage of time
needs to be close enough to that of the other systems involved, there
is no need to rely on the world clock when determining whether an
interval has passed.
Instead, by obtaining a value from the native clock when the interval
has started only the native clock is necessary to determine when this
interval ends. As the native clock does not rely on any external
time sources, the implementation becomes resistant to the
difficulties of coordinating with these sources.
However, using the native clock in this way comes with a caveat.
Since the native clock is not subject to any adjustments by timing
protocols, it is not adjusted for the error introduced by clock
drift. While this is likely of little consequence for short
intervals, it may become significant for intervals that span long
periods of time.
Malhotra, et al. Expires May 22, 2020 [Page 6]
Internet-Draft implementation-advice November 2019
The choice of clock to be used is situation-specific. If a certain
amount of clock drift can be tolerated or if time intervals are
short, implementors may prefer to use the native clock. However, if
precise timing over long periods is required, then the implementors
have no choice but to fall back to world clock
6. Accessing the Native Clock on Selected Operating Systems
In most operating systems, the standard functions to access time use
the world clock since that is normally what users would expect. This
section provides an overview how the native clock can be accesses on
some common operating systems.
6.1. POSIX
POSIX defines a system C API function which may provide native time:
"clock_gettime()", when used with a "clock_id" of "CLOCK_MONOTONIC".
Note that on some systems "CLOCK_MONOTONIC" is still influenced by an
external time source (for syntonizing the clock rate) and the non-
standard "CLOCK_MONITONIC_RAW" needs to be used for clock values not
influenced by an external time source and not susceptible for time-
shifting attacks.
6.2. Microsoft Window
In the Microsoft Windows operating system, native time is called
'Windows Time' and can be accessed through the "GetTickCount" and
"GetTickCount64" API functions. The returned value is nomially the
number of milliseconds since system start. "GetTickCount" will
return a 32 bit value while "GetTickCount64" returns a value 64 bits
wide that will wrap around less
7. IANA Considerations
This memo includes no request to IANA.
8. Security Considerations
Time is a fundamental component for the security guarantees claimed
by various applications. A system that uses a time distribution
protocol may be affected by the security aspects of the time
protocol. The security considerations of time protocols in general
are discussed in [RFC7384]. This document discusses the security
considerations with respect to implementing time values in
applications in various sections.
Malhotra, et al. Expires May 22, 2020 [Page 7]
Internet-Draft implementation-advice November 2019
9. References
9.1. Normative References
[RFC7384] Mizrahi, T., "Security Requirements of Time Protocols in
Packet Switched Networks", RFC 7384, DOI 10.17487/RFC7384,
October 2014, <https://www.rfc-editor.org/info/rfc7384>.
9.2. Informative References
[ANABM] Malhotra, A. and S. Goldberg, "Attacking NTP's
Authenticated Broadcast Mode", 2016,
<https://eprint.iacr.org/2016/055>.
[ANTP] Malhotra, A., Cohen, I., Brakke, E., and S. Goldberg,
"Attacking the Network Time Protocol", 2015,
<https://eprint.iacr.org/2015/1020>.
[BPHSTS] Jose, J., "Bypassing HTTP Strict Transport Security",
2014, <https://www.blackhat.com/docs/eu-14/materials/eu-
14-Selvi-Bypassing-HTTP-Strict-Transport-Security-wp.pdf>.
[SECNTP] Malhotra, A., Gundy, M., Varia, M., Kennedy, H., Gardner,
J., and S. Goldberg, "The Security of NTP's Datagram
Protocol", 2016, <http://eprint.iacr.org/2016/1006>.
Appendix A. Acknowledgements
We are thankful to Sharon Goldberg and Benno Overreinder for useful
discussions. Thanks to Dieter Sibold, Joachim Fabini and Denis
Reilly, for value input and suggestions.
Authors' Addresses
Aanchal Malhotra
Boston University
111 Cummington Mall
Boston 02215
USA
Email: aanchal4@bu.edu
Malhotra, et al. Expires May 22, 2020 [Page 8]
Internet-Draft implementation-advice November 2019
Kristof Teichel
Physikalisch-Technische Bundesanstalt
Bundesallee 100
Braunschweig D-38116
Germany
Email: kristof.teichel@ptb.de
Martin Hoffmann
NLnet Labs
Science Park 400
Amsterdam 1098 XH
Netherlands
Email: martin@nlnetlabs.nl
Willem Toorop
NLnet Labs
Science Park 400
Amsterdam 1098 XH
Netherlands
Email: willem@nlnetlabs.nl
Malhotra, et al. Expires May 22, 2020 [Page 9]