Internet DRAFT - draft-ietf-roll-security-threats
draft-ietf-roll-security-threats
Routing Over Low-Power and Lossy Networks T. Tsao
Internet-Draft R. Alexander
Intended status: Informational Cooper Power Systems
Expires: April 05, 2015 M. Dohler
CTTC
V. Daza
A. Lozano
Universitat Pompeu Fabra
M. Richardson, Ed.
Sandelman Software Works
October 02, 2014
A Security Threat Analysis for Routing Protocol for Low-power and lossy
networks (RPL)
draft-ietf-roll-security-threats-11
Abstract
This document presents a security threat analysis for the Routing
Protocol for Low-power and lossy networks (RPL, ROLL). The
development builds upon previous work on routing security and adapts
the assessments to the issues and constraints specific to low-power
and lossy networks. A systematic approach is used in defining and
evaluating the security threats. Applicable countermeasures are
application specific and are addressed in relevant applicability
statements.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 05, 2015.
Copyright Notice
Tsao, et al. Expires April 05, 2015 [Page 1]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
Copyright (c) 2014 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Relationship to other documents . . . . . . . . . . . . . . . 4
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Considerations on RPL Security . . . . . . . . . . . . . . . 5
4.1. Routing Assets and Points of Access . . . . . . . . . . . 6
4.2. The ISO 7498-2 Security Reference Model . . . . . . . . . 8
4.3. Issues Specific to or Amplified in LLNs . . . . . . . . . 10
4.4. RPL Security Objectives . . . . . . . . . . . . . . . . . 12
5. Threat Sources . . . . . . . . . . . . . . . . . . . . . . . 13
6. Threats and Attacks . . . . . . . . . . . . . . . . . . . . . 13
6.1. Threats due to failures to Authenticate . . . . . . . . . 14
6.1.1. Node Impersonation . . . . . . . . . . . . . . . . . 14
6.1.2. Dummy Node . . . . . . . . . . . . . . . . . . . . . 14
6.1.3. Node Resource Spam . . . . . . . . . . . . . . . . . 14
6.2. Threats due to failure to keep routing information
confidential . . . . . . . . . . . . . . . . . . . . . . 15
6.2.1. Routing Exchange Exposure . . . . . . . . . . . . . . 15
6.2.2. Routing Information (Routes and Network Topology)
Exposure . . . . . . . . . . . . . . . . . . . . . . 15
6.3. Threats and Attacks on Integrity . . . . . . . . . . . . 16
6.3.1. Routing Information Manipulation . . . . . . . . . . 16
6.3.2. Node Identity Misappropriation . . . . . . . . . . . 17
6.4. Threats and Attacks on Availability . . . . . . . . . . . 17
6.4.1. Routing Exchange Interference or Disruption . . . . . 17
6.4.2. Network Traffic Forwarding Disruption . . . . . . . . 17
6.4.3. Communications Resource Disruption . . . . . . . . . 19
6.4.4. Node Resource Exhaustion . . . . . . . . . . . . . . 19
7. Countermeasures . . . . . . . . . . . . . . . . . . . . . . . 20
7.1. Confidentiality Attack Countermeasures . . . . . . . . . 20
7.1.1. Countering Deliberate Exposure Attacks . . . . . . . 20
7.1.2. Countering Passive Wiretapping Attacks . . . . . . . 21
7.1.3. Countering Traffic Analysis . . . . . . . . . . . . . 22
7.1.4. Countering Remote Device Access Attacks . . . . . . . 23
Tsao, et al. Expires April 05, 2015 [Page 2]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
7.2. Integrity Attack Countermeasures . . . . . . . . . . . . 23
7.2.1. Countering Unauthorized Modification Attacks . . . . 23
7.2.2. Countering Overclaiming and Misclaiming Attacks . . . 24
7.2.3. Countering Identity (including Sybil) Attacks . . . . 24
7.2.4. Countering Routing Information Replay Attacks . . . . 25
7.2.5. Countering Byzantine Routing Information Attacks . . 25
7.3. Availability Attack Countermeasures . . . . . . . . . . . 26
7.3.1. Countering HELLO Flood Attacks and ACK Spoofing
Attacks . . . . . . . . . . . . . . . . . . . . . . . 26
7.3.2. Countering Overload Attacks . . . . . . . . . . . . . 27
7.3.3. Countering Selective Forwarding Attacks . . . . . . . 28
7.3.4. Countering Sinkhole Attacks . . . . . . . . . . . . . 29
7.3.5. Countering Wormhole Attacks . . . . . . . . . . . . . 30
8. RPL Security Features . . . . . . . . . . . . . . . . . . . . 31
8.1. Confidentiality Features . . . . . . . . . . . . . . . . 31
8.2. Integrity Features . . . . . . . . . . . . . . . . . . . 32
8.3. Availability Features . . . . . . . . . . . . . . . . . . 33
8.4. Key Management . . . . . . . . . . . . . . . . . . . . . 33
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 34
10. Security Considerations . . . . . . . . . . . . . . . . . . . 34
11. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 34
12. References . . . . . . . . . . . . . . . . . . . . . . . . . 34
12.1. Normative References . . . . . . . . . . . . . . . . . . 34
12.2. Informative References . . . . . . . . . . . . . . . . . 35
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 38
1. Introduction
In recent times, networked electronic devices have found an
increasing number of applications in various fields. Yet, for
reasons ranging from operational application to economics, these
wired and wireless devices are often supplied with minimum physical
resources; the constraints include those on computational resources
(RAM, clock speed, storage), communication resources (duty cycle,
packet size, etc.), but also form factors that may rule out user
access interfaces (e.g., the housing of a small stick-on switch), or
simply safety considerations (e.g., with gas meters). As a
consequence, the resulting networks are more prone to loss of traffic
and other vulnerabilities. The proliferation of these low-power and
lossy networks (LLNs), however, are drawing efforts to examine and
address their potential networking challenges. Securing the
establishment and maintenance of network connectivity among these
deployed devices becomes one of these key challenges.
This document presents a threat analysis for securing the Routing
Protocol for LLNs (RPL). The process requires two steps. First, the
analysis will be used to identify pertinent security issues. The
second step is to identify necessary countermeasures to secure RPL.
Tsao, et al. Expires April 05, 2015 [Page 3]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
As there are multiple ways to solve the problem and the specific
tradeoffs are deployment specific, the specific countermeasure to be
used is detailed in applicability statements.
This document uses [ISO.7498-2.1988]] model, which describes
Authentication, Access Control, Data Confidentiality, Data Integrity,
and Non-Repudiation security services and to which Availability is
added. As explained below, Non-Repudiation does not apply to routing
protocols.
Many of the issues in this document were also covered in The IAB
Smart Object Workshop [RFC6574], and The IAB Smart Object Security
Workshop [I-D.gilger-smart-object-security-workshop].
All of this document concerns itself with securing the control plane
traffic. As such it does not address authorization or authentication
of application traffic. RPL uses multicast as part of its protocol,
and therefore mechanisms which RPL uses to secure this traffic might
also be applicable to MPL control traffic as well: the important part
is that the threats are similar.
2. Relationship to other documents
ROLL has specified a set of routing protocols for Lossy and Low-
resource Networks (LLN) [RFC6550]. A number of applicability texts
describes a subset of these protocols and the conditions which make
the subset the correct choice. The text recommends and motivates the
accompanying parameter value ranges. Multiple applicability domains
are recognized including: Building and Home, and Advanced Metering
Infrastructure. The applicability domains distinguish themselves in
the way they are operated, their performance requirements, and the
most probable network structures. Each applicability statement
identifies the distinguishing properties according to a common set of
subjects described in as many sections.
The common set of security threats herein are referred to by the
applicability statements, and that series of documents describes the
preferred security settings and solutions within the applicability
statement conditions. This applicability statements may recommend
more light weight security solutions and specify the conditions under
which these solutions are appropriate.
3. Terminology
This document adopts the terminology defined in [RFC6550], in
[RFC4949], and in [RFC7102].
Tsao, et al. Expires April 05, 2015 [Page 4]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
The terms control plane and forwarding plane are used consistently
with section 1 of [RFC6192].
The term DODAG is from [RFC6550].
EAP-TLS is defined in [RFC5216].
PANA is defined in [RFC5191].
CCM mode is defined in [RFC3610].
[RFC7102] introduces the term Sleepy Node, referring to a node which
may somtimes go into a low-power state, suspending protocol
communications
The terms SSID, ESSID and PAN refer to network identifiers, defined
in [IEEE.802.11] and [IEEE.802.15.4].
Although this is not a protocol specification, the key words "MUST",
"MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT",
"RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119] in order to
clarify and emphasize the guidance and directions to implementers and
deployers of LLN nodes that utilize RPL.
4. Considerations on RPL Security
Routing security, in essence, ensures that the routing protocol
operates correctly. It entails implementing measures to ensure
controlled state changes on devices and network elements, both based
on external inputs (received via communications) or internal inputs
(physical security of device itself and parameters maintained by the
device, including, e.g., clock). State changes would thereby involve
not only authorization of injector's actions, authentication of
injectors, and potentially confidentiality of routing data, but also
proper order of state changes through timeliness, since seriously
delayed state changes, such as commands or updates of routing tables,
may negatively impact system operation. A security assessment can
therefore begin with a focus on the assets [RFC4949] that may be the
target of the state changes and the access points in terms of
interfaces and protocol exchanges through which such changes may
occur. In the case of routing security, the focus is directed
towards the elements associated with the establishment and
maintenance of network connectivity.
This section sets the stage for the development of the analysis by
applying the systematic approach proposed in [Myagmar2005] to the
routing security, while also drawing references from other reviews
Tsao, et al. Expires April 05, 2015 [Page 5]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
and assessments found in the literature, particularly, [RFC4593] and
[Karlof2003] (i.e. selective forwarding, wormhole and sinkhole
attacks). The subsequent subsections begin with a focus on the
elements of a generic routing process that is used to establish
routing assets and points of access to the routing functionality.
Next, the [ISO.7498-2.1988] security model is briefly described.
Then, consideration is given to issues specific to or amplified in
LLNs. This section concludes with the formulation of a set of
security objectives for RPL.
4.1. Routing Assets and Points of Access
An asset is an important system resource (including information,
process, or physical resource), the access to, corruption or loss of
which adversely affects the system. In the control plane context, an
asset is information about the network, processes used to manage and
manipulate this data, and the physical devices on which this data is
stored and manipulated. The corruption or loss of these assets may
adversely impact the control plane of the network. Within the same
context, a point of access is an interface or protocol that
facilitates interaction between control plane assets. Identifying
these assets and points of access will provide a basis for
enumerating the attack surface of the control plane.
A level-0 data flow diagram [Yourdon1979] is used here to identify
the assets and points of access within a generic routing process.
The use of a data flow diagram allows for a clear and concise model
of the way in which routing nodes interact and process information,
and hence provides a context for threats and attacks. The goal of
the model is to be as detailed as possible so that corresponding
assets, points of access, and process in an individual routing
protocol can be readily identified.
Figure 1 shows that nodes participating in the routing process
transmit messages to discover neighbors and to exchange routing
information; routes are then generated and stored, which may be
maintained in the form of the protocol forwarding table. The nodes
use the derived routes for making forwarding decisions.
...................................................
: :
: :
|Node_i|<------->(Routing Neighbor _________________ :
: Discovery)------------>Neighbor Topology :
: -------+--------- :
: | :
|Node_j|<------->(Route/Topology +--------+ :
Tsao, et al. Expires April 05, 2015 [Page 6]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
: Exchange) | :
: | V ______ :
: +---->(Route Generation)--->Routes :
: ---+-- :
: | :
: Routing on a Node Node_k | :
...................................................
|
|Forwarding |
|On Node_l|<-------------------------------------------+
Notation:
(Proc) A process Proc
________
topology A structure storing neighbor adjacency (parent/child)
--------
________
routes A structure storing the forwarding information base (FIB)
--------
|Node_n| An external entity Node_n
-------> Data flow
Figure 1: Data Flow Diagram of a Generic Routing Process
It is seen from Figure 1 that
o Assets include
* routing and/or topology information;
* route generation process;
* communication channel resources (bandwidth);
* node resources (computing capacity, memory, and remaining
energy);
* node identifiers (including node identity and ascribed
attributes such as relative or absolute node location).
o Points of access include
Tsao, et al. Expires April 05, 2015 [Page 7]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
* neighbor discovery;
* route/topology exchange;
* node physical interfaces (including access to data storage).
A focus on the above list of assets and points of access enables a
more directed assessment of routing security; for example, it is
readily understood that some routing attacks are in the form of
attempts to misrepresent routing topology. Indeed, the intention of
the security threat analysis is to be comprehensive. Hence, some of
the discussion which follows is associated with assets and points of
access that are not directly related to routing protocol design but
nonetheless provided for reference since they do have direct
consequences on the security of routing.
4.2. The ISO 7498-2 Security Reference Model
At the conceptual level, security within an information system in
general and applied to RPL in particular is concerned with the
primary issues of authentication, access control, data
confidentiality, data integrity, and non-repudiation. In the context
of RPL:
Authentication
Authentication involves the mutual authentication of the
routing peers prior to exchanging route information (i.e., peer
authentication) as well as ensuring that the source of the
route data is from the peer (i.e., data origin authentication).
[RFC5548] points out that LLNs can be drained by
unauthenticated peers before configuration. [RFC5673] requires
availability of open and untrusted side channels for new
joiners, and it requires strong and automated authentication so
that networks can automatically accept or reject new joiners.
Access Control
Access Control provides protection against unauthorized use of
the asset, and deals with the authorization of a node.
Confidentiality
Tsao, et al. Expires April 05, 2015 [Page 8]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
Confidentiality involves the protection of routing information
as well as routing neighbor maintenance exchanges so that only
authorized and intended network entities may view or access it.
Because LLNs are most commonly found on a publicly accessible
shared medium, e.g., air or wiring in a building, and sometimes
formed ad hoc, confidentiality also extends to the neighbor
state and database information within the routing device since
the deployment of the network creates the potential for
unauthorized access to the physical devices themselves.
Integrity
Integrity entails the protection of routing information and
routing neighbor maintenance exchanges, as well as derived
information maintained in the database, from unauthorized
modification, insertions, deletions or replays. to be addressed
beyond the routing protocol.
Non-repudiation
Non-repudiation is the assurance that the transmission and/or
reception of a message cannot later be denied. The service of
non-repudiation applies after-the-fact and thus relies on the
logging or other capture of on-going message exchanges and
signatures. Routing protocols typically do not have a notion
of repudiation, so non-repudiation services are not required.
Further, with the LLN application domains as described in
[RFC5867] and [RFC5548], proactive measures are much more
critical than retrospective protections. Finally, given the
significant practical limits to on-going routing transaction
logging and storage and individual device digital signature
verification for each exchange, non-repudiation in the context
of routing is an unsupportable burden that bears no further
considered as an RPL security issue.
It is recognized that, besides those security issues captured in the
ISO 7498-2 model, availability, is a security requirement:
Availability
Availability ensures that routing information exchanges and
forwarding services need to be available when they are required
for the functioning of the serving network. Availability will
apply to maintaining efficient and correct operation of routing
and neighbor discovery exchanges (including needed information)
and forwarding services so as not to impair or limit the
network's central traffic flow function
Tsao, et al. Expires April 05, 2015 [Page 9]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
It should be emphasized here that for RPL security the above
requirements must be complemented by the proper security policies and
enforcement mechanisms to ensure that security objectives are met by
a given RPL implementation.
4.3. Issues Specific to or Amplified in LLNs
The requirements work detailed in Urban Requirements ([RFC5548]),
Industrial Requirements ([RFC5673]), Home Automation ([RFC5826], and
Building Automation ([RFC5867]) have identified specific issues and
constraints of routing in LLNs. The following is a list of
observations from those requirements and evaluation of their impact
on routing security considerations.
Limited energy, memory, and processing node resources
As a consequence of these constraints, there is an even more
critical need than usual for a careful study of trade-offs on
which and what level of security services are to be afforded
during the system design process. The chosen security
mechanisms also needs to work within these constraints.
Synchronization of security states with sleepy nodes [RFC7102]
is yet another issue. A non-rechargeable battery powered node
may well be limited in energy for it's lifetime: once
exchausted, it may well never function again.
Large scale of rolled out network
The possibly numerous nodes to be deployed make manual on-site
configuration unlikely. For example, an urban deployment can
see several hundreds of thousands of nodes being installed by
many installers with a low level of expertise. Nodes may be
installed and not activated for many years, and additional
nodes may be added later on, which may be from old inventory.
The lifetime of the network is measured in decades, and this
complicates the operation of key management.
Autonomous operations
Self-forming and self-organizing are commonly prescribed
requirements of LLNs. In other words, a routing protocol
designed for LLNs needs to contain elements of ad hoc
networking and in most cases cannot rely on manual
configuration for initialization or local filtering rules.
Network topology/ownership changes, partitioning or merging, as
well as node replacement, can all contribute to complicating
the operations of key management.
Highly directional traffic
Some types of LLNs see a high percentage of their total traffic
traverse between the nodes and the LLN Border Routers (LBRs)
Tsao, et al. Expires April 05, 2015 [Page 10]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
where the LLNs connect to non-LLNs. The special routing status
of and the greater volume of traffic near the LBRs have routing
security consequences as a higher valued attack target. In
fact, when Point-to-MultiPoint (P2MP) and MultiPoint-to-Point
(MP2P) traffic represents a majority of the traffic, routing
attacks consisting of advertising incorrect preferred routes
can cause serious damage.
While it might seem that nodes higher up in the acyclic graph
(i.e. those with lower rank) should be secured in a stronger
fashion, it is not in general easy to predict which nodes will
occupy those positions until after deployment. Issues of
redundancy and inventory control suggests that any node might
wind up in such a sensitive attack position, so all nodes to be
capable of being fully secured.
In addition, even if it were possible to predict which nodes
will occupy positions of lower rank and provision them with
stronger security mechanisms, in the absense of a strong
authorization model, any node could advertise an incorrect
preferred route.
Unattended locations and limited physical security
Many applications have the nodes deployed in unattended or
remote locations; furthermore, the nodes themselves are often
built with minimal physical protection. These constraints
lower the barrier of accessing the data or security material
stored on the nodes through physical means.
Support for mobility
On the one hand, only a limited number of applications require
the support of mobile nodes, e.g., a home LLN that includes
nodes on wearable health care devices or an industry LLN that
includes nodes on cranes and vehicles. On the other hand, if a
routing protocol is indeed used in such applications, it will
clearly need to have corresponding security mechanisms.
Additionally nodes may appear to move from one side of a wall
to another without any actual motion involved, the result of
changes to electromagnetic properties, such as opening and
closing of a metal door.
Support for multicast and anycast
Support for multicast and anycast is called out chiefly for
large-scale networks. Since application of these routing
mechanisms in autonomous operations of many nodes is new, the
consequence on security requires careful consideration.
Tsao, et al. Expires April 05, 2015 [Page 11]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
The above list considers how an LLN's physical constraints, size,
operations, and variety of application areas may impact security.
However, it is the combinations of these factors that particularly
stress the security concerns. For instance, securing routing for a
large number of autonomous devices that are left in unattended
locations with limited physical security presents challenges that are
not found in the common circumstance of administered networked
routers. The following subsection sets up the security objectives
for the routing protocol designed by the ROLL WG.
4.4. RPL Security Objectives
This subsection applies the ISO 7498-2 model to routing assets and
access points, taking into account the LLN issues, to develop a set
of RPL security objectives.
Since the fundamental function of a routing protocol is to build
routes for forwarding packets, it is essential to ensure that:
o routing/topology information integrity remains intact during
transfer and in storage;
o routing/topology information is used by authorized entities;
o routing/topology information is available when needed.
In conjunction, it is necessary to be assured that
o authorized peers authenticate themselves during the routing
neighbor discovery process;
o the routing/topology information received is generated according
to the protocol design.
However, when trust cannot be fully vested through authentication of
the principals alone, i.e., concerns of insider attack, assurance of
the truthfulness and timeliness of the received routing/topology
information is necessary. With regard to confidentiality, protecting
the routing/topology information from unauthorized exposure may be
desirable in certain cases but is in itself less pertinent in general
to the routing function.
One of the main problems of synchronizing security states of sleepy
nodes, as listed in the last subsection, lies in difficulties in
authentication; these nodes may not have received in time the most
recent update of security material. Similarly, the issues of minimal
manual configuration, prolonged rollout and delayed addition of
nodes, and network topology changes also complicate key management.
Tsao, et al. Expires April 05, 2015 [Page 12]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
Hence, routing in LLNs needs to bootstrap the authentication process
and allow for flexible expiration scheme of authentication
credentials.
The vulnerability brought forth by some special-function nodes, e.g.,
LBRs, requires the assurance, particularly in a security context,
o of the availability of communication channels and node resources;
o that the neighbor discovery process operates without undermining
routing availability.
There are other factors which are not part of RPL but directly
affecting its function. These factors include weaker barrier of
accessing the data or security material stored on the nodes through
physical means; therefore, the internal and external interfaces of a
node need to be adequate for guarding the integrity, and possibly the
confidentiality, of stored information, as well as the integrity of
routing and route generation processes.
Each individual system's use and environment will dictate how the
above objectives are applied, including the choices of security
services as well as the strengths of the mechanisms that must be
implemented. The next two sections take a closer look at how the RPL
security objectives may be compromised and how those potential
compromises can be countered.
5. Threat Sources
[RFC4593] provides a detailed review of the threat sources: outsiders
and byzantine. RPL has the same threat sources.
6. Threats and Attacks
This section outlines general categories of threats under the ISO
7498-2 model and highlights the specific attacks in each of these
categories for RPL. As defined in [RFC4949], a threat is "a
potential for violation of security, which exists when there is a
circumstance, capability, action, or event that could breach security
and cause harm."
An attack is "an assault on system security that derives from an
intelligent threat, i.e., an intelligent act that is a deliberate
attempt (especially in the sense of a method or technique) to evade
security services and violate the security policy of a system."
The subsequent subsections consider the threats and the attacks that
can cause security breaches under the ISO 7498-2 model to the routing
Tsao, et al. Expires April 05, 2015 [Page 13]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
assets and via the routing points of access identified in
Section 4.1. The assessment steps through the security concerns of
each routing asset and looks at the attacks that can exploit routing
points of access. The threats and attacks identified are based on
the routing model analysis and associated review of the existing
literature. The source of the attacks is assumed to be from either
inside or outside attackers. While some attackers inside the network
will be using compromised nodes, and therefore are only able to do
what an ordinary node can ("node-equivalent"), other attacks may not
limited in memory, CPU, power consumption or long term storage.
Moore's law favours the attacker with access to the latest
capabilities, while the defenders will remain in place for years to
decades.
6.1. Threats due to failures to Authenticate
6.1.1. Node Impersonation
If an attacker can join a network using any identity, then it may be
able to assume the role of a legitimate (and existing node). It may
be able to report false readings (in metering applications), or
provide inappropriate control messages (in control systems involving
actuators) if the security of the application is implied by the
security of the routing system.
Even in systems where there application layer security, the ability
to impersonate a node would permit an attacker to direct traffic to
itself. This may permit various on-path attacks which would
otherwise be difficult, such replaying, delaying, or duplicating
(application) control messages.
6.1.2. Dummy Node
If an attacker can join a network using any identify, then it can
pretend to be a legitimate node, receiving any service legitimate
nodes receive. It may also be able to report false readings (in
metering applications), or provide inappropriate authorizations (in
control systems involving actuators), or perform any other attacks
that are facilitated by being able to direct traffic towards itself.
6.1.3. Node Resource Spam
If an attacker can join a network with any identify, then it can
continously do so with new (random) identities. This act may drain
down the resources of the network (battery, RAM, bandwidth). This
may cause legitimate nodes of the network to be unable to
communicate.
Tsao, et al. Expires April 05, 2015 [Page 14]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
6.2. Threats due to failure to keep routing information confidential
The assessment in Section 4.2 indicates that there are attacks
against the confidentiality of routing information at all points of
access. This threat may result in disclosure, as described in
Section 3.1.2 of [RFC4593], and may involve a disclosure of routing
information.
6.2.1. Routing Exchange Exposure
Routing exchanges include both routing information as well as
information associated with the establishment and maintenance of
neighbor state information. As indicated in Section 4.1, the
associated routing information assets may also include device
specific resource information, such as available memory, remaining
power, etc., that may be metrics of the routing protocol.
The routing exchanges will contain reachability information, which
would identify the relative importance of different nodes in the
network. Nodes higher up in the DODAG, to which more streams of
information flow, would be more interesting targets for other
attacks, and routing exchange exposures can identify them.
6.2.2. Routing Information (Routes and Network Topology) Exposure
Routes (which may be maintained in the form of the protocol
forwarding table) and neighbor topology information are the products
of the routing process that are stored within the node device
databases.
The exposure of this information will allow attackers to gain direct
access to the configuration and connectivity of the network thereby
exposing routing to targeted attacks on key nodes or links. Since
routes and neighbor topology information is stored within the node
device, attacks on the confidentiality of the information will apply
to the physical device including specified and unspecified internal
and external interfaces.
The forms of attack that allow unauthorized access or disclosure of
the routing information will include:
o Physical device compromise;
o Remote device access attacks (including those occurring through
remote network management or software/field upgrade interfaces).
Both of these attack vectors are considered a device specific issue,
and are out of scope for RPL to defend against. In some
Tsao, et al. Expires April 05, 2015 [Page 15]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
applications, physical device compromise may be a real threat and it
may be necessary to provide for other devices to securely detect a
compromised device and react quickly to exclude it.
6.3. Threats and Attacks on Integrity
The assessment in Section 4.2 indicates that information and identity
assets are exposed to integrity threats from all points of access.
In other words, the integrity threat space is defined by the
potential for exploitation introduced by access to assets available
through routing exchanges and the on-device storage.
6.3.1. Routing Information Manipulation
Manipulation of routing information that range from neighbor states
to derived routes will allow unauthorized sources to influence the
operation and convergence of the routing protocols and ultimately
impact the forwarding decisions made in the network.
Manipulation of topology and reachability information will allow
unauthorized sources to influence the nodes with which routing
information is exchanged and updated. The consequence of
manipulating routing exchanges can thus lead to sub-optimality and
fragmentation or partitioning of the network by restricting the
universe of routers with which associations can be established and
maintained.
A sub-optimal network may use too much power and/or may congest some
routes leading to premature failure of a node, and a denial of
service on the entire network.
In addition, being able to attract network traffic can make a
blackhole attack more damaging.
The forms of attack that allow manipulation to compromise the content
and validity of routing information include
o Falsification, including overclaiming and misclaiming (claiming
routes to devices which the device can not in fact reach);
o Routing information replay;
o Byzantine (internal) attacks that permit corruption of routing
information in the node even where the node continues to be a
validated entity within the network (see, for example, [RFC4593]
for further discussions on Byzantine attacks);
o Physical device compromise or remote device access attacks.
Tsao, et al. Expires April 05, 2015 [Page 16]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
6.3.2. Node Identity Misappropriation
Falsification or misappropriation of node identity between routing
participants opens the door for other attacks; it can also cause
incorrect routing relationships to form and/or topologies to emerge.
Routing attacks may also be mounted through less sophisticated node
identity misappropriation in which the valid information broadcast or
exchanged by a node is replayed without modification. The receipt of
seemingly valid information that is however no longer current can
result in routing disruption, and instability (including failure to
converge). Without measures to authenticate the routing participants
and to ensure the freshness and validity of the received information
the protocol operation can be compromised. The forms of attack that
misuse node identity include
o Identity attacks, including Sybil attacks (see [Sybil2002]) in
which a malicious node illegitimately assumes multiple identities;
o Routing information replay.
6.4. Threats and Attacks on Availability
The assessment in Section 4.2 indicates that the process and
resources assets are exposed to threats against availability; attacks
in this category may exploit directly or indirectly information
exchange or forwarding (see [RFC4732] for a general discussion).
6.4.1. Routing Exchange Interference or Disruption
Interference is the threat action and disruption is threat
consequence that allows attackers to influence the operation and
convergence of the routing protocols by impeding the routing
information exchange.
The forms of attack that allow interference or disruption of routing
exchange include:
o Routing information replay;
o ACK spoofing;
o Overload attacks. (Section 7.3.2)
In addition, attacks may also be directly conducted at the physical
layer in the form of jamming or interfering.
6.4.2. Network Traffic Forwarding Disruption
Tsao, et al. Expires April 05, 2015 [Page 17]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
The disruption of the network traffic forwarding capability will
undermine the central function of network routers and the ability to
handle user traffic. This affects the availability of the network
because of the potential to impair the primary capability of the
network.
In addition to physical layer obstructions, the forms of attack that
allows disruption of network traffic forwarding include [Karlof2003]
o Selective forwarding attacks;
|Node_1|--(msg1|msg2|msg3)-->|Attacker|--(msg1|msg3)-->|Node_2|
Figure 2: Selective forwarding example
o Wormhole attacks;
|Node_1|-------------Unreachable---------x|Node_2|
| ^
| Private Link |
'-->|Attacker_1|===========>|Attacker_2|--'
Figure 3: Wormhole Attacks
o Sinkhole attacks.
Tsao, et al. Expires April 05, 2015 [Page 18]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
|Node_1| |Node_4|
| |
`--------. |
Falsify as \ |
Good Link \ | |
To Node_5 \ | |
\ V V
|Node_2|-->|Attacker|--Not Forwarded---x|Node_5|
^ ^ \
| | \ Falsify as
| | \Good Link
/ | To Node_5
,-------' |
| |
|Node_3| |Node_i|
Figure 4: sinkhole attack example
These attacks are generally done to both control plane and forwarding
plane traffic. A system that prevents control plane traffic (RPL
messages) from being diverted in these ways will also prevent actual
data from being diverted.
6.4.3. Communications Resource Disruption
Attacks mounted against the communication channel resource assets
needed by the routing protocol can be used as a means of disrupting
its operation. However, while various forms of Denial of Service
(DoS) attacks on the underlying transport subsystem will affect
routing protocol exchanges and operation (for example physical layer
RF jamming in a wireless network or link layer attacks), these
attacks cannot be countered by the routing protocol. As such, the
threats to the underlying transport network that supports routing is
considered beyond the scope of the current document. Nonetheless,
attacks on the subsystem will affect routing operation and so must be
directly addressed within the underlying subsystem and its
implemented protocol layers.
6.4.4. Node Resource Exhaustion
A potential threat consequence can arise from attempts to overload
the node resource asset by initiating exchanges that can lead to the
exhaustion of processing, memory, or energy resources. The
establishment and maintenance of routing neighbors opens the routing
process to engagement and potential acceptance of multiple
neighboring peers. Association information must be stored for each
peer entity and for the wireless network operation provisions made to
Tsao, et al. Expires April 05, 2015 [Page 19]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
periodically update and reassess the associations. An introduced
proliferation of apparent routing peers can therefore have a negative
impact on node resources.
Node resources may also be unduly consumed by attackers attempting
uncontrolled topology peering or routing exchanges, routing replays,
or the generating of other data traffic floods. Beyond the
disruption of communications channel resources, these consequences
may be able to exhaust node resources only where the engagements are
able to proceed with the peer routing entities. Routing operation
and network forwarding functions can thus be adversely impacted by
node resources exhaustion that stems from attacks that include:
o Identity (including Sybil) attacks (see [Sybil2002]);
o Routing information replay attacks;
o HELLO-type flood attacks;
o Overload attacks. (Section 7.3.2)
7. Countermeasures
By recognizing the characteristics of LLNs that may impact routing,
this analysis provides the basis for understanding the capabilities
within RPL used to deter the identified attacks and mitigate the
threats. The following subsections consider such countermeasures by
grouping the attacks according to the classification of the ISO
7498-2 model so that associations with the necessary security
services are more readily visible.
7.1. Confidentiality Attack Countermeasures
Attacks to disclosure routing information may be mounted at the level
of the routing information assets, at the points of access associated
with routing exchanges between nodes, or through device interface
access. To gain access to routing/topology information, the attacker
may rely on a compromised node that deliberately exposes the
information during the routing exchange process, may rely on passive
wiretapping or traffic analysis, or may attempt access through a
component or device interface of a tampered routing node.
7.1.1. Countering Deliberate Exposure Attacks
A deliberate exposure attack is one in which an entity that is party
to the routing process or topology exchange allows the routing/
topology information or generated route information to be exposed to
an unauthorized entity.
Tsao, et al. Expires April 05, 2015 [Page 20]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
For instance, due to mis-configuration or inappropriate enabling of a
diagnostic interface, an entity might be copying ("bridging") traffic
from a secured ESSID/PAN to an unsecured interface.
A prerequisite to countering this attack is to ensure that the
communicating nodes are authenticated prior to data encryption
applied in the routing exchange. The authentication ensures the LLN
starts with trusted nodes, but it does not provide an indication of
whether the node has been compromised.
Reputation systems could be be used to help when some nodes may sleep
for extended periods of times. It is also unclear if resulting
dataset would even fit into constrained devices.
To mitigate the risk of deliberate exposure, the process that
communicating nodes use to establish session keys must be peer-to-
peer (i.e., between the routing initiating and responding nodes). As
is pointed out in [RFC4107], automatic key management is critical for
good security. This helps ensure that neither node is exchanging
routing information with another peer without the knowledge of both
communicating peers. For a deliberate exposure attack to succeed,
the comprised node will need to be more overt and take independent
actions in order to disclose the routing information to 3rd party.
Note that the same measures which apply to securing routing/topology
exchanges between operational nodes must also extend to field tools
and other devices used in a deployed network where such devices can
be configured to participate in routing exchanges.
7.1.2. Countering Passive Wiretapping Attacks
A passive wiretap attack seeks to breach routing confidentiality
through passive, direct analysis and processing of the information
exchanges between nodes.
Passive wiretap attacks can be directly countered through the use of
data encryption for all routing exchanges. Only when a validated and
authenticated node association is completed will routing exchange be
allowed to proceed using established session keys and an agreed
encryption algorithm. The mandatory to implement CCM mode AES-128
method, is described in [RFC3610], and is believed to be secure
against a brute force attack by even the most well-equipped
adversary.
Tsao, et al. Expires April 05, 2015 [Page 21]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
The significant challenge for RPL is in the provisioning of the key,
which in some modes of RFC6550 is used network-wide. RFC6550 does
not solve this problem, and it is the subject of significant future
work: see, for instance: [AceCharterProposal], [SolaceProposal],
[SmartObjectSecurityWorkshop].
A number of deployments, such as [ZigBeeIP] specify no layer-3/RPL
encryption or authentication and rely upon similiar security at
layer-2. These networks are immune to outside wiretapping attacks,
but are vulnerable to passive (and active) routing attacks through
compromises of nodes. (see Section 8.2).
Section 10.9 of [RFC6550] specifies AES-128 in CCM mode with a 32-bit
MAC.
Section 5.6 Zigbee IP [ZigBeeIP] specifies use of CCM, with PANA and
EAP-TLS for key management.
7.1.3. Countering Traffic Analysis
Traffic analysis provides an indirect means of subverting
confidentiality and gaining access to routing information by allowing
an attacker to indirectly map the connectivity or flow patterns
(including link-load) of the network from which other attacks can be
mounted. The traffic analysis attack on an LLN, especially one
founded on shared medium, is passive and relies on the ability to
read the immutable source/destination layer-2 and/or layer-3 routing
information that must remain unencrypted to permit network routing.
One way in which passive traffic analysis attacks can be muted is
through the support of load balancing that allows traffic to a given
destination to be sent along diverse routing paths. RPL does not
generally support multi-path routing within a single DODAG. Multiple
DODAGs are supported in the protocol, and an implementation could
make use of that. RPL does not have any inherent or standard way to
guarantee that the different DODAGs would have significantly diverse
paths. Having the diverse DODAGs routed at different border routers
might work in some instances, and this could be combined with a
multipath technology like MPTCP ([RFC6824]. It is unlikely that it
will be affordable in many LLNs, as few deployments will have memory
space for more than a few sets of DODAG tables.
Another approach to countering passive traffic analysis could be for
nodes to maintain constant amount of traffic to different
destinations through the generation of arbitrary traffic flows; the
drawback of course would be the consequent overhead and energy
expenditure.
Tsao, et al. Expires April 05, 2015 [Page 22]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
The only means of fully countering a traffic analysis attack is
through the use of tunneling (encapsulation) where encryption is
applied across the entirety of the original packet source/destination
addresses. Deployments which use layer-2 security that includes
encryption already do this for all traffic.
7.1.4. Countering Remote Device Access Attacks
Where LLN nodes are deployed in the field, measures are introduced to
allow for remote retrieval of routing data and for software or field
upgrades. These paths create the potential for a device to be
remotely accessed across the network or through a provided field
tool. In the case of network management a node can be directly
requested to provide routing tables and neighbor information.
To ensure confidentiality of the node routing information against
attacks through remote access, any local or remote device requesting
routing information must be authenticated, and must be authorized for
that access. Since remote access is not invoked as part of a routing
protocol, security of routing information stored on the node against
remote access will not be addressable as part of the routing
protocol.
7.2. Integrity Attack Countermeasures
Integrity attack countermeasures address routing information
manipulation, as well as node identity and routing information
misuse. Manipulation can occur in the form of falsification attack
and physical compromise. To be effective, the following development
considers the two aspects of falsification, namely, the unauthorized
modifications and the overclaiming and misclaiming content. The
countering of physical compromise was considered in the previous
section and is not repeated here. With regard to misuse, there are
two types of attacks to be deterred, identity attacks and replay
attacks.
7.2.1. Countering Unauthorized Modification Attacks
Unauthorized modifications may occur in the form of altering the
message being transferred or the data stored. Therefore, it is
necessary to ensure that only authorized nodes can change the portion
of the information that is allowed to be mutable, while the integrity
of the rest of the information is protected, e.g., through well-
studied cryptographic mechanisms.
Tsao, et al. Expires April 05, 2015 [Page 23]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
Unauthorized modifications may also occur in the form of insertion or
deletion of messages during protocol changes. Therefore, the
protocol needs to ensure the integrity of the sequence of the
exchange sequence.
The countermeasure to unauthorized modifications needs to:
o implement access control on storage;
o provide data integrity service to transferred messages and stored
data;
o include sequence number under integrity protection.
7.2.2. Countering Overclaiming and Misclaiming Attacks
Both overclaiming and misclaiming aim to introduce false routes or a
false topology that would not occur otherwise, while there are not
necessarily unauthorized modifications to the routing messages or
information. In order to counter overclaiming, the capability to
determine unreasonable routes or topology is required.
The counter to overclaiming and misclaiming may employ:
o comparison with historical routing/topology data;
o designs which restrict realizable network topologies.
RPL includes no specific mechanisms in the protocol to counter
overclaims or misclaims. An implementation could have specific
heuristics implemented locally.
7.2.3. Countering Identity (including Sybil) Attacks
Identity attacks, sometimes simply called spoofing, seek to gain or
damage assets whose access is controlled through identity. In
routing, an identity attacker can illegitimately participate in
routing exchanges, distribute false routing information, or cause an
invalid outcome of a routing process.
A perpetrator of Sybil attacks assumes multiple identities. The
result is not only an amplification of the damage to routing, but
extension to new areas, e.g., where geographic distribution is
explicitly or implicitly an asset to an application running on the
LLN, for example, the LBR in a P2MP or MP2P LLN.
RPL includes specific public key based authentication at layer-3 that
provide for authorization. Many deployments use layer-2 security
Tsao, et al. Expires April 05, 2015 [Page 24]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
that includes admission controls at layer-2 using mechanisms such as
PANA.
7.2.4. Countering Routing Information Replay Attacks
In many routing protocols, message replay can result in false
topology and/or routes. This is often counted with some kind of
counter to ensure the freshness of the message. Replay of a current,
literal RPL message are in general idempotent to the topology. An
older (lower DODAGVersionNumber) message, if replayed would be
rejected as being stale. The trickle algorithm further dampens the
effect of any such replay, as if the message was current, then it
would contain the same information as before, and it would cause no
network changes.
Replays may well occur in some radio technologies (not very likely,
802.15.4) as a result of echos or reflections, and so some replays
must be assumed to occur naturally.
Note that for there to be no affect at all, the replay must be done
with the same apparent power for all nodes receiving the replay. A
change in apparent power might change the metrics through changes to
the ETX and therefore might affect the routing even though the
contents of the packet were never changed. Any replay which appears
to be different should be analyzed as a Selective Forwarding Attack,
Sinkhole Attack or Wormhole Attack.
7.2.5. Countering Byzantine Routing Information Attacks
Where a node is captured or compromised but continues to operate for
a period with valid network security credentials, the potential
exists for routing information to be manipulated. This compromise of
the routing information could thus exist in spite of security
countermeasures that operate between the peer routing devices.
Consistent with the end-to-end principle of communications, such an
attack can only be fully addressed through measures operating
directly between the routing entities themselves or by means of
external entities able to access and independently analyze the
routing information. Verification of the authenticity and liveliness
of the routing entities can therefore only provide a limited counter
against internal (Byzantine) node attacks.
For link state routing protocols where information is flooded with,
for example, areas (OSPF [RFC2328]) or levels (ISIS [RFC7142]),
countermeasures can be directly applied by the routing entities
through the processing and comparison of link state information
received from different peers. By comparing the link information
Tsao, et al. Expires April 05, 2015 [Page 25]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
from multiple sources decisions can be made by a routing node or
external entity with regard to routing information validity; see
Chapter 2 of [Perlman1988] for a discussion on flooding attacks.
For distance vector protocols, such as RPL, where information is
aggregated at each routing node it is not possible for nodes to
directly detect Byzantine information manipulation attacks from the
routing information exchange. In such cases, the routing protocol
must include and support indirect communications exchanges between
non-adjacent routing peers to provide a secondary channel for
performing routing information validation. S-RIP [Wan2004] is an
example of the implementation of this type of dedicated routing
protocol security where the correctness of aggregate distance vector
information can only be validated by initiating confirmation
exchanges directly between nodes that are not routing neighbors.
RPL does not provide any direct mechanisms like S-RIP. It does
listen to multiple parents, and may switch parents if it begins to
suspect that it is being lied to.
7.3. Availability Attack Countermeasures
As alluded to before, availability requires that routing information
exchanges and forwarding mechanisms be available when needed so as to
guarantee proper functioning of the network. This may, e.g., include
the correct operation of routing information and neighbor state
information exchanges, among others. We will highlight the key
features of the security threats along with typical countermeasures
to prevent or at least mitigate them. We will also note that an
availability attack may be facilitated by an identity attack as well
as a replay attack, as was addressed in Section 7.2.3 and
Section 7.2.4, respectively.
7.3.1. Countering HELLO Flood Attacks and ACK Spoofing Attacks
HELLO Flood [Karlof2003],[I-D.suhopark-hello-wsn] and ACK Spoofing
attacks are different but highly related forms of attacking an LLN.
They essentially lead nodes to believe that suitable routes are
available even though they are not and hence constitute a serious
availability attack.
A HELLO attack mounted against RPL would involve sending out (or
replaying) DIO messages by the attacker. Lower power LLN nodes might
then attempt to join the DODAG at a lower rank than they would
otherwise.
The most effective method from [I-D.suhopark-hello-wsn] is the verify
bidirectionality. A number of layer-2 links are arranged in
Tsao, et al. Expires April 05, 2015 [Page 26]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
controller/spoke arrangements, and continuously are validating
connectivity at layer 2.
In addition, in order to calculate metrics, the ETX must be computed,
and this involves, in general, sending a number of messages between
nodes which are believed to be adjacent.
[I-D.kelsey-intarea-mesh-link-establishment] is one such protocol.
In order to join the DODAG, a DAO message is sent upwards. In RPL
the DAO is acknowledged by the DAO-ACK message. This clearly checks
bidirectionality at the control plane.
As discussed in section 5.1, [I-D.suhopark-hello-wsn] a receiver with
a sensitive receiver could well hear the DAOs, and even send DAO-ACKs
as well. Such a node is a form of wormhole attack.
These attacks are also all easily defended against using either
layer-2 or layer-3 authentication. Such an attack could only be made
against a completely open network (such as might be used for
provisioning new nodes), or by a compromised node.
7.3.2. Countering Overload Attacks
Overload attacks are a form of DoS attack in that a malicious node
overloads the network with irrelevant traffic, thereby draining the
nodes' energy store more quickly, when the nodes rely on batteries or
energy scavenging. It thus significantly shortens the lifetime of
networks of energy-constrained nodes and constitutes another serious
availability attack.
With energy being one of the most precious assets of LLNs, targeting
its availability is a fairly obvious attack. Another way of
depleting the energy of an LLN node is to have the malicious node
overload the network with irrelevant traffic. This impacts
availability since certain routes get congested which:
o renders them useless for affected nodes and data can hence not be
delivered;
o makes routes longer as shortest path algorithms work with the
congested network;
o depletes battery and energy scavenging nodes more quickly and thus
shortens the network's availability at large.
Overload attacks can be countered by deploying a series of mutually
non-exclusive security measures:
Tsao, et al. Expires April 05, 2015 [Page 27]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
o introduce quotas on the traffic rate each node is allowed to send;
o isolate nodes which send traffic above a certain threshold based
on system operation characteristics;
o allow only trusted data to be received and forwarded.
As for the first one, a simple approach to minimize the harmful
impact of an overload attack is to introduce traffic quotas. This
prevents a malicious node from injecting a large amount of traffic
into the network, even though it does not prevent said node from
injecting irrelevant traffic at all. Another method is to isolate
nodes from the network at the network layer once it has been detected
that more traffic is injected into the network than allowed by a
prior set or dynamically adjusted threshold. Finally, if
communication is sufficiently secured, only trusted nodes can receive
and forward traffic which also lowers the risk of an overload attack.
Receiving nodes that validate signatures and sending nodes that
encrypt messages need to be cautious of cryptographic processing
usage when validating signatures and encrypting messages. Where
feasible, certificates should be validated prior to use of the
associated keys to counter potential resource overloading attacks.
The associated design decision needs to also consider that the
validation process requires resources and thus itself could be
exploited for attacks. Alternatively, resource management limits can
be placed on routing security processing events (see the comment in
Section 6, paragraph 4, of [RFC5751]).
7.3.3. Countering Selective Forwarding Attacks
Selective forwarding attacks are a form of DoS attack which impacts
the availability of the generated routing paths.
A selective forwarding attack may be done by a node involved with the
routing process, or it may be done by what otherwise appears to be a
passive antenna or other RF feature or device, but is in fact an
active (and selective) device. An RF antenna/repeater which is not
selective, is not a threat.
Tsao, et al. Expires April 05, 2015 [Page 28]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
An insider malicious node basically blends neatly in with the network
but then may decide to forward and/or manipulate certain packets. If
all packets are dropped, then this attacker is also often referred to
as a "black hole". Such a form of attack is particularly dangerous
if coupled with sinkhole attacks since inherently a large amount of
traffic is attracted to the malicious node and thereby causing
significant damage. In a shared medium, an outside malicious node
would selectively jam overheard data flows, where the thus caused
collisions incur selective forwarding.
Selective Forwarding attacks can be countered by deploying a series
of mutually non-exclusive security measures:
o multipath routing of the same message over disjoint paths;
o dynamically selecting the next hop from a set of candidates.
The first measure basically guarantees that if a message gets lost on
a particular routing path due to a malicious selective forwarding
attack, there will be another route which successfully delivers the
data. Such a method is inherently suboptimal from an energy
consumption point of view; it is also suboptimal from a network
utilization perspective. The second method basically involves a
constantly changing routing topology in that next-hop routers are
chosen from a dynamic set in the hope that the number of malicious
nodes in this set is negligible. A routing protocol that allows for
disjoint routing paths may also be useful.
7.3.4. Countering Sinkhole Attacks
In sinkhole attacks, the malicious node manages to attract a lot of
traffic mainly by advertising the availability of high-quality links
even though there are none [Karlof2003]. It hence constitutes a
serious attack on availability.
The malicious node creates a sinkhole by attracting a large amount
of, if not all, traffic from surrounding neighbors by advertising in
and outwards links of superior quality. Affected nodes hence eagerly
route their traffic via the malicious node which, if coupled with
other attacks such as selective forwarding, may lead to serious
availability and security breaches. Such an attack can only be
executed by an inside malicious node and is generally very difficult
to detect. An ongoing attack has a profound impact on the network
topology and essentially becomes a problem of flow control.
Sinkhole attacks can be countered by deploying a series of mutually
non-exclusive security measures:
Tsao, et al. Expires April 05, 2015 [Page 29]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
o use geographical insights for flow control;
o isolate nodes which receive traffic above a certain threshold;
o dynamically pick up next hop from set of candidates;
o allow only trusted data to be received and forwarded.
A canary node could periodically call home (using a cryptographic
process), with the home system noting if it fails to call in. This
provides detection of a problem, but does not mitigate it, and it may
have significant energy consequences for the LLN.
Some LLNs may provide for geolocation services, often derived from
solving triangulation equations from radio delay calculations, such
calculations could in theory be subverted by a sinkhole that
transmitted at precisely the right power in a node to node fashion.
While geographic knowledge could help assure that traffic always went
in the physical direction desired, it would not assure that the
traffic was taking the most efficient route, as the lowest cost real
route might be match the physical topology; such as when different
parts of an LLN are connected by high-speed wired networks.
7.3.5. Countering Wormhole Attacks
In wormhole attacks at least two malicious nodes claim to have a
short path between themselves [Karlof2003]. This changes the
availability of certain routing paths and hence constitutes a serious
security breach.
Essentially, two malicious insider nodes use another, more powerful,
transmitter to communicate with each other and thereby distort the
would-be-agreed routing path. This distortion could involve
shortcutting and hence paralyzing a large part of the network; it
could also involve tunneling the information to another region of the
network where there are, e.g., more malicious nodes available to aid
the intrusion or where messages are replayed, etc.
In conjunction with selective forwarding, wormhole attacks can create
race conditions which impact topology maintenance, routing protocols
as well as any security suits built on "time of check" and "time of
use".
A pure wormhole attack is nearly impossible to detect. A wormhole
which is used in order to subsequently mount another kind of attack
would be defeated by defeating the other attack. A perfect wormhole,
in which there is nothing adverse that occurs to the traffic, would
Tsao, et al. Expires April 05, 2015 [Page 30]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
be difficult to call an attack. The worst thing that a benign
wormhole can do in such a situation is to cease to operate (become
unstable), causing the network to have to recalculate routes.
A highly unstable wormhole is no different than a radio opaque (i.e.
metal) door that opens and closes a lot. RPL includes hysteresis in
its objective functions [RFC6719] in an attempt to deal with frequent
changes to the ETX between nodes.
8. RPL Security Features
The assessments and analysis in Section 6 examined all areas of
threats and attacks that could impact routing, and the
countermeasures presented in Section 7 were reached without confining
the consideration to means only available to routing. This section
puts the results into perspective; dealing with those threats which
are endemic to this field, those which have been mitigated through
RPL protocol design, and those which require specific decisions to be
made as part of provisioning a network.
The first part of this section, Section 8.1 to Section 8.3, is a
description of RPL security features that address specific threats.
The second part of this section, Section 8.4, discusses issues of
provisioning of security aspects that may impact routing but that
also require considerations beyond the routing protocol, as well as
potential approaches.
RPL employs multicast and so these alternative communications modes
MUST be secured with the same routing security services specified in
this section. Furthermore, irrespective of the modes of
communication, nodes MUST provide adequate physical tamper resistance
commensurate with the particular application domain environment to
ensure the confidentiality, integrity, and availability of stored
routing information.
8.1. Confidentiality Features
With regard to confidentiality, protecting the routing/topology
information from unauthorized disclosure is not directly essential to
maintaining the routing function. Breaches of confidentiality may
lead to other attacks or the focusing of an attacker's resources (see
Section 6.2) but does not of itself directly undermine the operation
of the routing function. However, to protect against, and reduce
consequences from other more direct attacks, routing information
should be protected. Thus, to secure RPL:
o implement payload encryption using layer-3 mechanisms described in
[RFC6550];
Tsao, et al. Expires April 05, 2015 [Page 31]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
o or: implement layer-2 confidentiality;
Where confidentiality is incorporated into the routing exchanges,
encryption algorithms and key lengths need to be specified in
accordance with the level of protection dictated by the routing
protocol and the associated application domain transport network.
For most networks, this means use of AES128 in CCM mode, but this
needs to be specified clearly in the applicability statement.
In terms of the life time of the keys, the opportunity to
periodically change the encryption key increases the offered level of
security for any given implementation. However, where strong
cryptography is employed, physical, procedural, and logical data
access protection considerations may have more significant impact on
cryptoperiod selection than algorithm and key size factors.
Nevertheless, in general, shorter cryptoperiods, during which a
single key is applied, will enhance security.
Given the mandatory protocol requirement to implement routing node
authentication as part of routing integrity (see Section 8.2), key
exchanges may be coordinated as part of the integrity verification
process. This provides an opportunity to increase the frequency of
key exchange and shorten the cryptoperiod as a complement to the key
length and encryption algorithm required for a given application
domain.
8.2. Integrity Features
The integrity of routing information provides the basis for ensuring
that the function of the routing protocol is achieved and maintained.
To protect integrity, RPL must either run using only the Secure
versions of the messages, or must run over a layer-2 that uses
channel binding between node identity and transmissions.
Some layer-2 security mechanisms use a single key for the entire
network, and these networks can not provide significant amount of
integrity protection, as any node that has that key may impersonate
any other node. This mode of operation is likely acceptable when an
entire deployment is under the control of a single administrative
entity.
Other layer-2 security mechanisms form a unique session key for every
pair of nodes that needs to communicate; this is often called a per-
link key. Such networks can provide a strong degree of origin
authentication and integrity on unicast messages.
However, some RPL messages are broadcast, and even when per-node
layer-2 security mechanisms are used, the integrity and origin
Tsao, et al. Expires April 05, 2015 [Page 32]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
authentication of broadcast messages can not be as trusted due to the
proliferation of the key used to secure them.
RPL has two specific options which are broadcast in RPL Control
Messages: the DODAG Information Object (DIO), and the DODAG
Information Solicitation (DIS). The purpose of the DIS is to cause
potential parents to reply with a DIO, so the integrity of the DIS is
not of great concern. The DIS may also be unicast.
The DIO is a critical piece of routing and carries many critical
parameters. RPL provides for asymmetric authentication at layer 3 of
the RPL Control Message carrying the DIO and this may be warranted in
some deployments. A node could, if it felt that the DIO that it had
received was suspicious, send a unicast DIS message to the node in
question, and that node would reply with a unicast DIS. Those
messages could be protected with the per-link key.
8.3. Availability Features
Availability of routing information is linked to system and network
availability which in the case of LLNs require a broader security
view beyond the requirements of the routing entities. Where
availability of the network is compromised, routing information
availability will be accordingly affected. However, to specifically
assist in protecting routing availability, nodes:
o MAY restrict neighborhood cardinality;
o MAY use multiple paths;
o MAY use multiple destinations;
o MAY choose randomly if multiple paths are available;
o MAY set quotas to limit transmit or receive volume;
o MAY use geographic information for flow control.
8.4. Key Management
The functioning of the routing security services requires keys and
credentials. Therefore, even though not directly a RPL security
requirement, an LLN MUST have a process for initial key and
credential configuration, as well as secure storage within the
associated devices. Anti-tampering SHOULD be a consideration in
physical design. Beyond initial credential configuration, an LLN is
also encouraged to have automatic procedures for the revocation and
replacement of the maintained security credentials.
Tsao, et al. Expires April 05, 2015 [Page 33]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
While RPL has secure modes, but some modes are impractical without
use of public key cryptography believed to be too expensive by many.
RPL layer-3 security will often depend upon existing LLN layer-2
security mechanisms, which provides for node authentication, but
little in the way of node authorization.
9. IANA Considerations
This memo includes no request to IANA.
10. Security Considerations
The analysis presented in this document provides security analysis
and design guidelines with a scope limited to RPL. Security services
are identified as requirements for securing RPL. The specific
mechanisms to be used to deal with each threat is specified in link-
layer and deployment specific applicability statements.
11. Acknowledgments
The authors would like to acknowledge the review and comments from
Rene Struik and JP Vasseur. The authors would also like to
acknowledge the guidance and input provided by the RPL Chairs, David
Culler, and JP Vasseur, and the Area Director Adrian Farrel.
This document started out as a combined threat and solutions
document. As a result of a series of security reviews performed by
Steve Kent, the document was split up by RPL co-Chair Michael
Richardson and security Area Director Sean Turner as it went through
the IETF publication process. The solutions to the threats are
application and layer-2 specific, and have therefore been moved to
the relevant applicability statements.
Ines Robles and Robert Cragie kept track of the many issues that were
raised during the development of this document
12. References
12.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4107] Bellovin, S. and R. Housley, "Guidelines for Cryptographic
Key Management", BCP 107, RFC 4107, June 2005.
[RFC6550] Winter, T., Thubert, P., Brandt, A., Hui, J., Kelsey, R.,
Levis, P., Pister, K., Struik, R., Vasseur, JP., and R.
Tsao, et al. Expires April 05, 2015 [Page 34]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
Alexander, "RPL: IPv6 Routing Protocol for Low-Power and
Lossy Networks", RFC 6550, March 2012.
[RFC6719] Gnawali, O. and P. Levis, "The Minimum Rank with
Hysteresis Objective Function", RFC 6719, September 2012.
[RFC7102] Vasseur, JP., "Terms Used in Routing for Low-Power and
Lossy Networks", RFC 7102, January 2014.
[ZigBeeIP]
ZigBee Public Document 15-002r00, "ZigBee IP
Specification", 2013.
12.2. Informative References
[AceCharterProposal]
Li, Kepeng., Ed., "Authentication and Authorization for
Constrained Environment Charter (work-in-progress)",
December 2013, <http://trac.tools.ietf.org/wg/core/trac/
wiki/ACE_charter>.
[I-D.gilger-smart-object-security-workshop]
Gilger, J. and H. Tschofenig, "Report from the 'Smart
Object Security Workshop', March 23, 2012, Paris, France",
draft-gilger-smart-object-security-workshop-02 (work in
progress), October 2013.
[I-D.kelsey-intarea-mesh-link-establishment]
Kelsey, R., "Mesh Link Establishment", draft-kelsey-
intarea-mesh-link-establishment-05 (work in progress),
February 2013.
[I-D.suhopark-hello-wsn]
Park, S., "Routing Security in Sensor Network: HELLO Flood
Attack and Defense", draft-suhopark-hello-wsn-00 (work in
progress), December 2005.
[IEEE.802.11]
, "Draft Standard for Information Technology -
Telecommunications and information exchange between
systems - Local and metropolitan area networks Specific
requirements - Part 11: Wireless LAN Medium Access Control
(MAC) and Physical Layer (PHY) specifications ", IEEE
802.11-REVma, 2006.
[IEEE.802.15.4]
, "Information technology - Telecommunications and
information exchange between systems - Local and
Tsao, et al. Expires April 05, 2015 [Page 35]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
metropolitan area networks - Specific requirements - Part
15.4: Wireless Medium Access Control (MAC) and Physical
Layer (PHY) Specifications for Low Rate Wireless Personal
Area Networks (LR-WPANs) ", IEEE Std 802.15.4-2006, June
2006, <http://standards.ieee.org/getieee802/802.15.html>.
[ISO.7498-2.1988]
International Organization for Standardization,
"Information Processing Systems - Open Systems
Interconnection Reference Model - Security Architecture",
ISO Standard 7498-2, 1988.
[Karlof2003]
Karlof, C. and D. Wagner, "Secure routing in wireless
sensor networks: attacks and countermeasures", Elsevier
AdHoc Networks Journal, Special Issue on Sensor Network
Applications and Protocols, 1(2):293-315, September 2003,
<http://nest.cs.berkeley.edu/papers/sensor-route-
security.pdf>.
[Myagmar2005]
Myagmar, S., Lee, AJ., and W. Yurcik, "Threat Modeling as
a Basis for Security Requirements", in Proceedings of the
Symposium on Requirements Engineering for Information
Security (SREIS'05), Paris, France, pp. 94-102, Aug 29,
2005.
[Perlman1988]
Perlman, N., "Network Layer Protocols with Byzantine
Robustness", MIT LCS Tech Report, 429, 1988.
[RFC2328] Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998.
[RFC3610] Whiting, D., Housley, R., and N. Ferguson, "Counter with
CBC-MAC (CCM)", RFC 3610, September 2003.
[RFC4593] Barbir, A., Murphy, S., and Y. Yang, "Generic Threats to
Routing Protocols", RFC 4593, October 2006.
[RFC4732] Handley, M., Rescorla, E., IAB, "Internet Denial-of-
Service Considerations", RFC 4732, December 2006.
[RFC4949] Shirey, R., "Internet Security Glossary, Version 2", RFC
4949, August 2007.
[RFC5191] Forsberg, D., Ohba, Y., Patil, B., Tschofenig, H., and A.
Yegin, "Protocol for Carrying Authentication for Network
Access (PANA)", RFC 5191, May 2008.
Tsao, et al. Expires April 05, 2015 [Page 36]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
[RFC5216] Simon, D., Aboba, B., and R. Hurst, "The EAP-TLS
Authentication Protocol", RFC 5216, March 2008.
[RFC5548] Dohler, M., Watteyne, T., Winter, T., and D. Barthel,
"Routing Requirements for Urban Low-Power and Lossy
Networks", RFC 5548, May 2009.
[RFC5673] Pister, K., Thubert, P., Dwars, S., and T. Phinney,
"Industrial Routing Requirements in Low-Power and Lossy
Networks", RFC 5673, October 2009.
[RFC5751] Ramsdell, B. and S. Turner, "Secure/Multipurpose Internet
Mail Extensions (S/MIME) Version 3.2 Message
Specification", RFC 5751, January 2010.
[RFC5826] Brandt, A., Buron, J., and G. Porcu, "Home Automation
Routing Requirements in Low-Power and Lossy Networks", RFC
5826, April 2010.
[RFC5867] Martocci, J., De Mil, P., Riou, N., and W. Vermeylen,
"Building Automation Routing Requirements in Low-Power and
Lossy Networks", RFC 5867, June 2010.
[RFC6192] Dugal, D., Pignataro, C., and R. Dunn, "Protecting the
Router Control Plane", RFC 6192, March 2011.
[RFC6574] Tschofenig, H. and J. Arkko, "Report from the Smart Object
Workshop", RFC 6574, April 2012.
[RFC6824] Ford, A., Raiciu, C., Handley, M., and O. Bonaventure,
"TCP Extensions for Multipath Operation with Multiple
Addresses", RFC 6824, January 2013.
[RFC7142] Shand, M. and L. Ginsberg, "Reclassification of RFC 1142
to Historic", RFC 7142, February 2014.
[SmartObjectSecurityWorkshop]
Klausen, T., Ed., "Workshop on Smart Object Security",
March 2012, <http://www.lix.polytechnique.fr/hipercom/
SmartObjectSecurity>.
[SolaceProposal]
Bormann, C., Ed., "Notes from the SOLACE ad-hoc at IETF85
(work-in-progress)", November 2012, <http://www.ietf.org/
mail-archive/web/solace/current/msg00015.html>.
[Sybil2002]
Tsao, et al. Expires April 05, 2015 [Page 37]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
Douceur, J., "The Sybil Attack", First International
Workshop on Peer-to-Peer Systems , March 2002.
[Wan2004] Wan, T., Kranakis, E., and PC. van Oorschot, "S-RIP: A
Secure Distance Vector Routing Protocol", in Proceedings
of the 2nd International Conference on Applied
Cryptography and Network Security, Yellow Mountain, China,
pp. 103-119, Jun. 8-11 2004.
[Yourdon1979]
Yourdon, E. and L. Constantine, "Structured Design",
Yourdon Press, New York, Chapter 10, pp. 187-222, 1979.
Authors' Addresses
Tzeta Tsao
Cooper Power Systems
910 Clopper Rd. Suite 201S
Gaithersburg, Maryland 20878
USA
Email: tzeta.tsao@cooperindustries.com
Roger K. Alexander
Cooper Power Systems
910 Clopper Rd. Suite 201S
Gaithersburg, Maryland 20878
USA
Email: roger.alexander@cooperindustries.com
Mischa Dohler
CTTC
Parc Mediterrani de la Tecnologia, Av. Canal Olimpic S/N
Castelldefels, Barcelona 08860
Spain
Email: mischa.dohler@cttc.es
Tsao, et al. Expires April 05, 2015 [Page 38]
Internet-Draft Security Threat Analysis for ROLL RPL October 2014
Vanesa Daza
Universitat Pompeu Fabra
P/ Circumval.lacio 8, Oficina 308
Barcelona 08003
Spain
Email: vanesa.daza@upf.edu
Angel Lozano
Universitat Pompeu Fabra
P/ Circumval.lacio 8, Oficina 309
Barcelona 08003
Spain
Email: angel.lozano@upf.edu
Michael Richardson (ed) (editor)
Sandelman Software Works
470 Dawson Avenue
Ottawa, ON K1Z5V7
Canada
Email: mcr+ietf@sandelman.ca
Tsao, et al. Expires April 05, 2015 [Page 39]
