Internet DRAFT - draft-ietf-snadlc-mib
draft-ietf-snadlc-mib
Internet Draft SNADLC MIB October 1993
Definitions of Managed Objects
for SNA Data Link Control
October 13, 1993
Jeff Hilgeman (chair)
Apertus Technologies, Inc.
7275 Flying Cloud Dr.
Eden Prarie, MN 55344
jeffh@apertus.com
Shannon D. Nix
Netlink, Inc.
3214 Spring Forest Rd.
Raleigh, NC 27604
sdn@netlink.com
Alan Bartkey
Sync Research, Inc.
7 Studebaker
Irvine, CA 92718
alan@sync.com
Wayne Clark (editor)
cisco Systems, Inc.
1525 O'Brien Dr.
Menlo Park, CA 94025
wclark@cisco.com
1. Status of this Memo
This document is an Internet Draft. Internet Drafts are
working documents of the Internet Engineering Task Force
(IETF), its Areas, and its Working Groups. Note that other
groups may also distribute working documents as Internet
Drafts.
9
9Expires April 13, 1994 [Page 1]
Internet Draft SNADLC MIB October 1993
Internet Drafts are draft documents valid for a maximum of six
months. Internet Drafts may be updated, replaced, or obsoleted
by other documents at any time. It is not appropriate to use
Internet Drafts as reference material or to cite them other
than as a "working draft" or "work in progress."
Please check the I-D abstract listing contained in each
Internet Draft directory to learn the current status of this
or any other Internet Draft.
2. Abstract
This Internet-Draft defines an extension to the Management
Information Base (MIB) for use with SNMP-based network
management. In particular, it defines objects for managing
the configuration, monitoring and control of data link
controls in an SNA environment. This draft identifies managed
objects for SNA Synchronous Data Link Control (SDLC) links
only. 2, 3.
This memo does not specify a standard for the Internet
community.
9
9Expires April 13, 1994 [Page 2]
Internet Draft SNADLC MIB October 1993
3. The SNMPv2 Network Management Framework
The SNMPv2 Network Management Framework consists of four major
components. They are:
o RFC 1441 which defines the SMI, the mechanisms used for
describing and naming objects for the purpose of
management.
o RFC 1213 defines MIB-II, the core set of managed objects
for the Internet suite of protocols.
o RFC 1445 which defines the administrative and other
architectural aspects of the framework.
o RFC 1448 which defines the protocol used for network
access to managed objects.
The Framework permits new objects to be defined for the
purpose of experimentation and evaluation.
3.1. Object Definitions
Managed objects are accessed via a virtual information store,
termed the Management Information Base or MIB. Objects in the
MIB are defined using the subset of Abstract Syntax Notation
One (ASN.1) defined in the SMI. In particular, each object
object type is named by an OBJECT IDENTIFIER, an
administratively assigned name. The object type together with
an object instance serves to uniquely identify a specific
instantiation of the object. For human convenience, we often
use a textual string, termed the descriptor, to refer to the
object type.
9
9Expires April 13, 1994 [Page 3]
Internet Draft SNADLC MIB October 1993
4. Overview
The SNADLC MIB is composed of two managed entities with, at
most, three tables each. The two managed entities for SDLC
are:
o Ports: the physical connection, and
o Link Stations: the logical connections on the Port.
The three management tables are:
o Adminstration: objects used for configuring and
controlling the operation of a Port or Link Station,
o Operational: objects that reflect the run-time state of
the Port or Link Station, and
o Statistics: objects that reflect the operating metrics of
the Port or Link Station.
Not all managed entities have all three tables. The following
are the actual tables found in this MIB:
1) Port Administration Table,
2) Port Operation Table,
3) Link Station Administration Table,
4) Link Station Operation Table,
5) Link Station Statistics Table,
There is no Port Statistics Table since most of the statistics
relevant to a particular port are a part of the RS-232 MIB in
RFC1317.
9
9Expires April 13, 1994 [Page 4]
Internet Draft SNADLC MIB October 1993
5. Definitions
SNA-DLC-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
Counter
FROM SNMPv2-SMI
DisplayString
FROM RFC1213-MIB
OBJECT-TYPE
FROM RFC-1212
experimental
FROM SNMPv2-SMI
DisplayString
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF;
-- This MIB Module uses the extended OBJECT-TYPE macro as
-- defined in RFC 1212.
snaDLC OBJECT IDENTIFIER ::= { experimental ? }
--
-- The following data link controls are modelled in this MIB module:
--
-- 1. SDLC
--
sdlc OBJECT IDENTIFIER ::= { snaDLC 1 }
--
-- THE SDLC GROUP
--
-- The following resources are modelled in the SDLC group of this MIB module:
--
-- 1. PORTS
-- 2. LINK STATIONS
sdlcPortGroup OBJECT IDENTIFIER ::= { sdlc 1 } -- Physical Ports
sdlcLstnGroup OBJECT IDENTIFIER ::= { sdlc 2 } -- Logical Link Stations
sdlcGlobals OBJECT IDENTIFIER ::= { sdlc 3 } -- Global SDLC Objects
Expires April 13, 1994 [Page 5]
Internet Draft SNADLC MIB October 1993
--
-- THE SDLC PORT GROUP
--
-- The following classes of information is modelled for each SDLC port:
--
-- 1. ADMINISTRATIVE ( read/write)
-- 2. OPERATIONAL ( read-only)
-- 3. STATISTICS (contained in RFC1317)
-- Information not found in this group is found in tables described in
-- the following RFCs:
--
-- 1. RFC1213 - MIB-II
--
-- TABLE INDEX
-- -------------------- ------------------
-- a. ifTable ifIndex
--
-- 2. RFC1317 - The RS232-like MIB
--
-- TABLE INDEX
-- -------------------- ------------------
-- a. rs232PortTable rs232PortIndex
-- b. rs232SyncPortTable rs232SyncPortIndex
-- c. rs232InSigTable rs232InSigPortIndex, rs232InSigName
-- d. rs232OutSigTable rs232OutSigPortIndex, rs232OutSigName
-- ** e. rs232AsyncPortTable rs232AsyncPortIndex
--
-- ** rs232AsyncPortTable for ISO 3309.3 ( Start-Stop SDLC).
-- *************************************************************
-- * *
-- * THE SDLC PORT ADMINISTRATIVE TABLE *
-- * *
-- *************************************************************
sdlcPortAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF SdlcPortAdminEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table contains objects that can be changed to
manage an SDLC port. Changing one of these
parameters may take effect in the operating port
immediately or may wait until the interface is
Expires April 13, 1994 [Page 6]
Internet Draft SNADLC MIB October 1993
restarted depending on the details of the
implementation.
Most of the objects in this read-write table
have corresponding read-only objects in the
sdlcPortOperTable that return the current operating
value.
The operating values may be different from these
configured values if a configured parameter
was changed after the interface was started."
::= { sdlcPortGroup 1 }
sdlcPortAdminEntry OBJECT-TYPE
SYNTAX SdlcPortAdminEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of configured values for an SDLC port."
INDEX { sdlcPortAdminIndex }
::= { sdlcPortAdminTable 1 }
SdlcPortAdminEntry ::= SEQUENCE
{
sdlcPortAdminIndex INTEGER,
sdlcPortAdminName DisplayString,
sdlcPortAdminType INTEGER,
sdlcPortAdminTopology INTEGER,
sdlcPortAdminISTATUS INTEGER,
sdlcPortAdminACTIVTO INTEGER,
sdlcPortAdminPAUSE INTEGER,
sdlcPortAdminSERVLIM INTEGER,
sdlcPortAdminSlowPollTimer INTEGER,
sdlcPortAdminRole INTEGER
}
sdlcPortAdminIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the SDLC port."
::= { sdlcPortAdminEntry 1 }
sdlcPortAdminName OBJECT-TYPE
Expires April 13, 1994 [Page 7]
Internet Draft SNADLC MIB October 1993
SYNTAX DisplayString (SIZE (1..8))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"An octet string that defines the physical port to
which this interface is assigned. It has
implementation-specific significance. Its value
shall be unique within the administered system.
It must contain only ASCII printable characters.
Should an implementation choose to accept a write
operation for this object, it causes the logical
port definition associated with the table instance
to be moved to a different physical port. A write
operation shall not take effect until the port is
cycled inactive."
::= { sdlcPortAdminEntry 2 }
sdlcPortAdminType OBJECT-TYPE
SYNTAX INTEGER
{
leased(1),
switched(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This parameter defines whether the SDLC port is
to connect to a leased or switched line. A write
operation to this administrative value shall not
take effect until the SDLC port has been cycled
inactive."
DEFVAL { leased }
::= { sdlcPortAdminEntry 3 }
sdlcPortAdminTopology OBJECT-TYPE
SYNTAX INTEGER
{
point-to-point(1),
multipoint(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This parameter defines whether the SDLC port is
operate in a point-to-point or multidropped
Expires April 13, 1994 [Page 8]
Internet Draft SNADLC MIB October 1993
topology. A write operation to this administrative
value shall not take effect until the SDLC port has
been cycled inactive."
DEFVAL { point-to-point }
::= { sdlcPortAdminEntry 4 }
sdlcPortAdminISTATUS
SYNTAX INTEGER
{
inactive(1),
active(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This parameter controls the initial value of the
administrative status, ifAdminStatus, of this SDLC
port at system start-up. Depending on the
implementation, a write operation to this
administrative object may not take effect until
the SDLC port has been cycled inactive."
DEFVAL { active }
::= { sdlcPortAdminEntry 5 }
sdlcPortAdminACTIVTO OBJECT-TYPE
SYNTAX INTEGER (0..120)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This parameter defines the period of time, in
seconds, the port will allow a switched line to
remain inactive ( no I-Frames) before disconnecting.
A value of zero indicates no timeout. Depending
on the implementation, a write operation to this
administered value may not take effect until the
port is cycled inactive.
This object is optional and does not have to be
implemented."
DEFVAL { 0 }
::= { sdlcPortAdminEntry 6 }
sdlcPortAdminPAUSE OBJECT-TYPE
SYNTAX INTEGER (1..6000)
ACCESS read-write
Expires April 13, 1994 [Page 9]
Internet Draft SNADLC MIB October 1993
STATUS mandatory
DESCRIPTION
"This object defines the minimum elapsed time, in
tenths of seconds, between any two traversals of
the poll list for a primary SDLC port. Depending
on the implementation, a write operation to this
administered value may not take effect until the
port is cycled inactive.
This object has meaning for primary SDLC ports only."
DEFVAL { 20 }
::= { sdlcPortAdminEntry 7 }
sdlcPortAdminSERVLIM OBJECT-TYPE
SYNTAX INTEGER (1..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object defines the number of times the active
poll list will be traversed before polling a station
on the slow poll list for a primary, multipoint SDLC
port. Depending on the implementation, a write
operation to this administered value may not take
effect until the port is cycled inactive.
This object has meaning for primary, multipoint SDLC
ports only."
DEFVAL { 20 }
::= { sdlcPortAdminEntry 9 }
sdlcPortAdminSlowPollTimer OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object describes the elapsed time between
polls for failed secondary link station addresses.
Depending on the implementation, a write operation
to this administered value may not take effect
until the port is cycled inactive.
This object has meaning for primary, multipoint SDLC
ports only."
DEFVAL { 20 }
::= { sdlcPortAdminEntry 10 }
Expires April 13, 1994 [Page 10]
Internet Draft SNADLC MIB October 1993
sdlcPortAdminRole OBJECT-TYPE
SYNTAX INTEGER
{
primary(1),
secondary(2),
negotiable(3)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object describes the role that the link
station shall assume the next time a connection is
established.
Even though this is defined as a port object, it
is a link station attribute in the sense that
a role is per link station. However, it is not
possible to vary link station roles on a particular
port (e.g. SDLC multidrop)."
::= { sdlcPortAdminEntry 11 }
-- *************************************************************
-- * *
-- * THE SDLC PORT OPERATIONAL TABLE *
-- * *
-- *************************************************************
sdlcPortOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF SdlcPortOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table contains current SDLC port parameters.
Many of these objects have corresponding objects
inthe sdlcPortAdmnTable."
::= { sdlcPortGroup 2 }
sdlcPortOperEntry OBJECT-TYPE
SYNTAX SdlcPortOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Currently set parameters for a specific SDLC port."
INDEX { sdlcPortOperIndex }
::= { sdlcPortOperTable 1 }
Expires April 13, 1994 [Page 11]
Internet Draft SNADLC MIB October 1993
SdlcPortOperEntry ::= SEQUENCE
{
sdlcPortOperIndex INTEGER,
sdlcPortOperName DisplayString,
sdlcPortOperType INTEGER,
sdlcPortOperTopology INTEGER,
sdlcPortOperISTATUS INTEGER,
sdlcPortOperACTIVTO INTEGER,
sdlcPortOperPAUSE INTEGER,
sdlcPortOperSlowPollMethod INTEGER,
sdlcPortOperSERVLIM INTEGER,
sdlcPortOperSlowPollTimer INTEGER,
sdlcPortOperRole INTEGER,
sdlcPortOperCreateTime TimeTicks,
sdlcPortOperLastModifyTime TimeTicks,
sdlcPortOperLastChangeTime TimeTicks,
sdlcPortOperLastFailTime TimeTicks,
sdlcPortOperLastFailCause INTEGER
}
sdlcPortOperIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the SDLC port."
::= { sdlcPortOperEntry 1 }
sdlcPortOperName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"An octet string that describes the physical port
to which this interface is currently attached. It
has implementation-specific significance."
::= { sdlcPortOperEntry 2 }
sdlcPortOperType OBJECT-TYPE
SYNTAX INTEGER
{
leased(1),
switched(2)
}
Expires April 13, 1994 [Page 12]
Internet Draft SNADLC MIB October 1993
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This parameter defines whether the SDLC port is
currently operating as though connected to a
leased or switched line."
::= { sdlcPortOperEntry 3 }
sdlcPortOperTopology OBJECT-TYPE
SYNTAX INTEGER
{
point-to-point(1),
multipoint(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This parameter defines whether the SDLC port is
currently operating in a point-to-point or
multidropped topology."
::= { sdlcPortOperEntry 4 }
sdlcPortOperISTATUS OBJECT-TYPE
SYNTAX INTEGER
{
inactive(1),
active(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This parameter describes the initial value of the
administrative status, ifAdminStatus, of this SDLC
port at last system start-up."
::= { sdlcPortOperEntry 5 }
sdlcPortOperACTIVTO OBJECT-TYPE
SYNTAX INTEGER (0..120)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This parameter describes the period of time, in
seconds, the port will allow a switched line to
remain inactive ( no I-Frames) before disconnecting.
Expires April 13, 1994 [Page 13]
Internet Draft SNADLC MIB October 1993
A value of zero indicates no timeout. "
::= { sdlcPortOperEntry 6 }
sdlcPortOperPAUSE OBJECT-TYPE
SYNTAX INTEGER (1..6000)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the current minimum elapsed
time, in tenths of seconds, between any two
traversals of the poll list for a primary SDLC port.
This object has meaning for primary SDLC ports only."
::= { sdlcPortOperEntry 7 }
sdlcPortOperSlowPollMethod OBJECT-TYPE
SYNTAX INTEGER
{
servlim(1),
pollpause(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object defines the exact method that is in
effect for periodically polling failed secondary
link station addresses.
This object has meaning for primary, multipoint SDLC
ports only."
DEFVAL { 20 }
::= { sdlcPortOperEntry 8 }
sdlcPortOperSERVLIM OBJECT-TYPE
SYNTAX INTEGER (1..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the number of times the active
poll list is currently being traversed before
polling a station on the slow poll list for a
primary, multipoint SDLC port.
This object has meaning for primary, multipoint
SDLC ports only."
Expires April 13, 1994 [Page 14]
Internet Draft SNADLC MIB October 1993
::= { sdlcPortOperEntry 9 }
sdlcPortOperSlowPollTimer OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the elapsed time between
polls for failed secondary link station addresses.
This object has meaning for primary, multipoint
SDLC ports only."
::= { sdlcPortOperEntry 10 }
sdlcPortOperRole OBJECT-TYPE
SYNTAX INTEGER
{
primary(1),
secondary(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the role that the link
station has assumed on this connection.
Even though this is defined as a port object, it
is a link station attribute in the sense that
a role is per link station. Note however, it is
not possible to vary link station roles on a
particular port (e.g. SDLC multidrop)."
::= { sdlcPortOperEntry 11 }
sdlcPortOperCreateTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the elapsed time, in
1/100ths of seconds, between system initialization and the
creation of this SDLC port."
::= { sdlcPortOperEntry 12 }
sdlcPortOperLastModifyTime OBJECT-TYPE
Expires April 13, 1994 [Page 15]
Internet Draft SNADLC MIB October 1993
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the elapsed time, in
1/100ths of seconds, between system initialization
and the last modification of this SDLC port. If
the port has not been modified, then this value
shall be zero."
::= { sdlcPortOperEntry 13 }
sdlcPortOperLastChangeTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the elapsed time, in
1/100ths of seconds, between system initialization
and the last state change for this SDLC port."
::= { sdlcPortOperEntry 14 }
sdlcPortOperLastFailTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the elapsed time, in
1/100ths of seconds, between system initialization
and the last failure of this SDLC port. If the
port has not failed, then this value shall be zero."
::= { sdlcPortOperEntry 15 }
sdlcPortOperLastFailCause OBJECT-TYPE
SYNTAX INTEGER
{
invalid(1),
physical(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This enumerated object describes the cause of the
last failure of this SDLC port. If the port has
not failed, then this value has no meaning."
::= { sdlcPortOperEntry 16 }
Expires April 13, 1994 [Page 16]
Internet Draft SNADLC MIB October 1993
--
-- THE SDLC LINK STATION GROUP
--
-- The following classes of information is modelled for each SDLC link
-- station:
--
-- 1. ADMINISTRATIVE ( read/write)
-- 2. OPERATIONAL ( read-only)
-- 3. STATISTICS ( read-only)
-- *************************************************************
-- * *
-- * THE SDLC LINK STATION ADMINISTRATIVE TABLE *
-- * *
-- *************************************************************
sdlcLSAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF SdlcLSAdminEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table contains objects that can be changed to
manage an SDLC link station. Changing one of these
parameters may take effect in the operating link
immediately or may wait until the link is restarted
depending on the details of the implementation.
Most of the objects in this read-write table have
corresponding read-only objects in the
sdlcLSOperTable that return the current operating
value.
The operating values may be different from these
configured values if changed by XID negotiation or
if a configured parameter was changed after the link
was started."
::= { sdlcLSGroup 1 }
sdlcLSAdminEntry OBJECT-TYPE
SYNTAX SdlcLSAdminEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of configured values for an SDLC link
Expires April 13, 1994 [Page 17]
Internet Draft SNADLC MIB October 1993
station."
INDEX { sdlcLSAdminIfIndex, sdlcLSAdminAddress }
::= { sdlcLSAdminTable 1 }
SdlcLSAdminEntry ::= SEQUENCE
{
sdlcLSAdminIfIndex INTEGER,
sdlcLSAdminAddress INTEGER,
sdlcLSAdminName INTEGER,
sdlcLSAdminState INTEGER,
sdlcLSAdminISTATUS INTEGER,
sdlcLSAdminMAXDATA INTEGER,
sdlcLSAdminREPLYTO INTEGER,
sdlcLSAdminMAXIN INTEGER,
sdlcLSAdminMAXOUT INTEGER,
sdlcLSAdminMODULO INTEGER,
sdlcLSAdminRETRIESm INTEGER,
sdlcLSAdminRETRIESt INTEGER,
sdlcLSAdminRETRIESn INTEGER,
sdlcLSAdminRNRLIMIT INTEGER,
sdlcLSAdminDATMODE INTEGER,
sdlcLSAdminGPoll INTEGER,
sdlcLSAdminXid INTEGER
}
sdlcLSAdminIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the SDLC port which
owns this link station."
::= { sdlcLSAdminEntry 1 }
sdlcLSAdminAddress OBJECT-TYPE
SYNTAX INTEGER(1..255)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This value is the poll address of the secondary
link station for this SDLC link. It uniquely
identifies the SDLC link station within a single
SDLC port."
::= { sdlcLSAdminEntry 2 }
9
9Expires April 13, 1994 [Page 18]
Internet Draft SNADLC MIB October 1993
sdlcLSAdminName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
ACCESS read-write
STATUS mandatory
DESCRIPTION
"An octet string that defines the local name of the
adjacent link station at the XID sender."
::= { sdlcLSAdminEntry 3 }
sdlcLSAdminState OBJECT-TYPE
SYNTAX INTEGER
{
inactive(1),
active(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the desired state of the SDLC
station. The managed system shall attempt to keep
the operational state, sdlcLSOperState, consistent
with this value."
DEFVAL { active }
::= { sdlcLSAdminEntry 4 }
sdlcLSAdminISTATUS OBJECT-TYPE
SYNTAX INTEGER
{
inactive(1),
active(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This parameter controls the desired state,
sdlcLSAdminState, of the SDLC link station at
system start-up."
DEFVAL { active }
::= { sdlcPortAdminEntry 5 }
sdlcLSAdminMAXDATA OBJECT-TYPE
SYNTAX INTEGER
{
265,
Expires April 13, 1994 [Page 19]
Internet Draft SNADLC MIB October 1993
521,
1033,
2057
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the maximum PDU size allowed
for the logical link. This value includes
the Transmission Header (TH) and Request Header (RH).
For link stations on switched SDLC lines, certain
implementions may choose to override this
administered value with the value negotiated in
the XID exchange.
Depending on implementation, a write operation to
this administrative value may not change the
operational value, sdlcLSOperMAXDATA, until the
link station has been cycled inactive."
::= { sdlcLSAdminEntry 6 }
sdlcLSAdminREPLYTO OBJECT-TYPE
SYNTAX INTEGER (1..600)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the reply timeout, in
tenths of seconds, for an SDLC link station. If the
link station does not receive a repsonse to a poll
or message before the specified time expires then
the appropriate error recovery shall be initiated.
Depending on the implementation, a write operation
to this administered value may not change the
operational value, sdlcLSOperREPLYTO, until the link
station is cycled inactive.
This object has no meaning for secondary SDLC link
stations."
DEFVAL { 10 }
::= { sdlcLSAdminEntry 7 }
sdlcLSAdminMAXIN OBJECT-TYPE
SYNTAX INTEGER (1..127)
Expires April 13, 1994 [Page 20]
Internet Draft SNADLC MIB October 1993
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the maximum number of
unacknowledged frames which an SDLC link station
may receive. This should range from one to modulus
minus one. The modulus is controlled by the object:
sdlcLSAdminModulus.
Depending on the implementation, a write operation
to this administered value may not change the
operational value, sdlcLSOperMAXIN, until the link
station is cycled inactive."
DEFVAL { 7 }
::= { sdlcLSAdminEntry 8 }
sdlcLSAdminMAXOUT OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the maximum consequetive
unacknowledged frames which an SDLC link station
shall send without an acknowledgement. This shall
range from one to modulus minus one. The modulus
is controlled by the object: sdlcLSAdminMODULO.
For link stations on switched SDLC lines, certain
implementions may choose to override this
administered value with the value negotiated in
the XID exchange.
Depending on the implementation, a write operation
to this administered value may not change the
operational value, sdlcLSOperMAXOUT, until the link
station is cycled inactive.
An implementation can support only modulo 8, only
modulo 128, or both."
DEFVAL { 1 }
::= { sdlcLSAdminEntry 9 }
sdlcLSAdminMODULO OBJECT-TYPE
SYNTAX INTEGER { 8, 128}
ACCESS read-write
Expires April 13, 1994 [Page 21]
Internet Draft SNADLC MIB October 1993
STATUS mandatory
DESCRIPTION
"This object controls the modulus for an SDLC link
station. This modulus determines the size of the
rotating acknowledgement window used the SDLC link
station pair.
Depending on the implementation, a write operation
to this administered value may not change the
operational value, sdlcLSOperMAXOUT, until the link
station is cycled inactive.
An implementation can support only modulo 8, only
modulo 128, or both."
DEFVAL { 8 }
::= { sdlcLSAdminEntry 10 }
sdlcLSAdminRETRIESm OBJECT-TYPE
SYNTAX INTEGER (0..128)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls number of retries in a retry
sequence for an SDLC link station. A retry sequence
is a series of retransmitted frames ( data or
control) for which no positive acknowledgement
is received.
The number of times that the retry sequence
is to be repeated is controlled by the object:
sdlcLSOperRETRIESn. The interval between
retry sequences is controlled by the object:
sdlcLSOperRETRIESt.
Depending on the implementation, a write operation
to this administered value may not change the
operational value, sdlcLSOperRETRIESm, until the
link station is cycled inactive."
DEFVAL { 15 }
::= { sdlcLSAdminEntry 11 }
sdlcLSAdminRETRIESt OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-write
STATUS mandatory
Expires April 13, 1994 [Page 22]
Internet Draft SNADLC MIB October 1993
DESCRIPTION
"This object controls the interval, in seconds,
between retry sequences for an SDLC link station if
multiple retry sequences are specified . A retry
sequence is a series of retransmitted frames ( data
or control) for which no positive acknowledgement
is received.
The number of repeated retries sequences is
controlled by the object: sdlcLSAdminRETRIESn.
The retries per sequence is controlled by the object:
sdlcLSAdminRETRIESm.
Depending on the implementation, a write operation
to this administered value may not change the
operational value, sdlcLSOperRETRIESt, until the
link station is cycled inactive."
DEFVAL { 0 }
::= { sdlcLSAdminEntry 12 }
sdlcLSAdminRETRIESn OBJECT-TYPE
SYNTAX INTEGER (0..127)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the number of times that
a retry sequence is repeated for an SDLC link
station. A retry sequence is a series of
retransmitted frames ( data or control) for which
no positive acknowledgement is received.
The interval between retry sequences is controlled
by the object: sdlcLSAdminRETRIESn. The retries
per sequence is controlled by the object:
sdlcLSAdminRETRIESm.
Depending on the implementation, a write operation
to this administered value may not change the
operational value, sdlcLSOperRETRIESn, until the
link station is cycled inactive."
DEFVAL { 0 }
::= { sdlcLSAdminEntry 13 }
sdlcLSAdminRNRLIMIT OBJECT-TYPE
SYNTAX INTEGER (1..90)
Expires April 13, 1994 [Page 23]
Internet Draft SNADLC MIB October 1993
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the length of time, in
minutes, that an SDLC link station will allow its
adjacent link station to remain in a busy (RNR)
state before declaring it inoperative.
Depending on the implementation, a write operation
to this administered value may not change the
operational value, sdlcLSOperRNRLIMIT, until the
link station is cycled inactive."
DEFVAL { 3 }
::= { sdlcLSAdminEntry 14 }
sdlcLSAdminDATMODE OBJECT-TYPE
SYNTAX INTEGER
{
half(1),
full(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls whether communications mode
with the adjacent link station is two-way-alternate
(half) or two-way-simultaneous (full).
Depending on the implementation, a write operation
to this administered value may not change the
operational value, sdlcLSOperDATMODE, until the
link station is cycled inactive."
DEFVAL { half }
::= { sdlcLSAdminEntry 15 }
sdlcLSAdminGPoll OBJECT-TYPE
SYNTAX INTEGER (0..254)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object describes the group poll address for
this link station instance.
Depending on the implementation, a write operation
to this administered value may not change the
Expires April 13, 1994 [Page 24]
Internet Draft SNADLC MIB October 1993
operational value, sdlcLSOperGPoll, until the
link station is cycled inactive."
::= { sdlcLSAdminEntry 16 }
sdlcLSAdminXid OBJECT-TYPE
SYNTAX INTEGER
{
no(1),
yes(2)
}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object controls the transmission of XID at
startup time.
Need more verbage on this from Alan Bartky of
Sync Research.
Depending on the implementation, a write operation
to this administered value may not change the
operational value, sdlcLSOperGPoll, until the
link station is cycled inactive."
::= { sdlcLSAdminEntry 17 }
-- *************************************************************
-- * *
-- * THE SDLC LINK STATION OPERATIONAL TABLE *
-- * *
-- *************************************************************
sdlcLSOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF SdlcLSOperEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"This table contains current SDLC link parameters.
Many of these objects have corresponding objects
inthe sdlcLSAdmnTable."
::= { sdlcLSGroup 2 }
sdlcLSOperEntry OBJECT-TYPE
SYNTAX SdlcLSOperEntry
ACCESS not-accessible
STATUS mandatory
Expires April 13, 1994 [Page 25]
Internet Draft SNADLC MIB October 1993
DESCRIPTION
"A list of status and control values for an
SDLC link station."
INDEX { sdlcLSOperIfIndex, sdlcLSOperAddress }
::= { sdlcLSOperTable 1 }
SdlcLSOperEntry ::= SEQUENCE
{
sdlcLSOperIfIndex INTEGER,
sdlcLSOperAddress INTEGER,
sdlcLSOperRole INTEGER,
sdlcLSOperState INTEGER,
sdlcLSOperMAXDATA INTEGER,
sdlcLSOperREPLYTO INTEGER,
sdlcLSOperMAXIN INTEGER,
sdlcLSOperMAXOUT INTEGER,
sdlcLSOperMODULO INTEGER,
sdlcLSOperRETRIESm INTEGER,
sdlcLSOperRETRIESt INTEGER,
sdlcLSOperRETRIESn INTEGER,
sdlcLSOperRNRLIMIT INTEGER,
sdlcLSOperDATMODE INTEGER,
sdlcLSOperCreateTime TimeTicks,
sdlcLSOperLastModifyTime TimeTicks,
sdlcLSOperLastChangeTime TimeTicks,
sdlcLSOperLastFailTime TimeTicks,
sdlcLSOperLastFailCause INTEGER,
sdlcLSOperLastFailCtrlIn OCTET STRING,
sdlcLSOperLastFailCtrlOut OCTET STRING,
sdlcLSOperLastFailFRMRInfo OCTET STRING,
sdlcLSOperLastFailREPLYTOs Counter,
sdlcLSOperEcho INTEGER,
sdlcLSOperGPoll INTEGER
}
sdlcLSOperIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the SDLC port which
owns this link station."
::= { sdlcLSOperEntry 1 }
sdlcLSOperAddress OBJECT-TYPE
Expires April 13, 1994 [Page 26]
Internet Draft SNADLC MIB October 1993
SYNTAX INTEGER(1..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value is the poll address of the secondary
link station in this SDLC link. It uniquely
identifies the SDLC link station within a single
SDLC port."
::= { sdlcLSOperEntry 2 }
sdlcLSOperRole OBJECT-TYPE
SYNTAX INTEGER
{
primary(1),
secondary(2),
negotiable(3)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current role that the link
station is assuming. This can only have a value of
negotiable(3) if the link station has an operational
state ( sdlcLSOperState) of discontacted(1)."
::= { sdlcLSOperEntry 3 }
sdlcLSOperState OBJECT-TYPE
SYNTAX INTEGER
{
discontacted(1),
contactPending(2),
contacted(3),
discontactPending(4)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the operational state of the
SDLC link station. The managed system shall attempt
to keep this value consistent with the administered
state, sdlcLSAdminState"
::= {sdlcLSOperEntry 4 }
sdlcLSOperMAXDATA OBJECT-TYPE
SYNTAX INTEGER
Expires April 13, 1994 [Page 27]
Internet Draft SNADLC MIB October 1993
{
265,
521,
1033,
2057
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current maximum PDU size
allowed for the logical link. This value includes
the Transmission Header (TH) and Request Header (RH).
This value may controlled by the administered MAXDATA,
sdlcLSAdminMAXDATA, or by the value negotiated in
the XID exchange for link stations on a switched
SDLC line."
::= { sdlcLSOperEntry 5 }
sdlcLSOperREPLYTO OBJECT-TYPE
SYNTAX INTEGER (1..600)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current reply timeout, in
tenths of seconds, for an SDLC link station. If the
link station does not receive a repsonse to a poll
or message before the specified time expires then
the appropriate error recovery shall be initiated.
This object has no meaning for secondary SDLC link
stationss."
::= { sdlcLSOperEntry 6 }
sdlcLSOperMAXIN OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current maximum number of
unacknowledged frames which an SDLC link station
may receive. This shall range from one to modulus
minus one."
::= { sdlcLSOperEntry 7 }
9
9Expires April 13, 1994 [Page 28]
Internet Draft SNADLC MIB October 1993
sdlcLSOperMAXOUT OBJECT-TYPE
SYNTAX INTEGER (1..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object controls the maximum consequetive
unacknowledged frames which an SDLC link station
shall send without an acknowledgement. This shall
range from one to modulus minus one. The modulus
is controlled by the object: sdlcLSAdminMODULO.
This value may controlled by the administered MAXOUT,
sdlcLSAdminMAXOUT, or by the value negotiated in
the XID exchange for link stations on a switched
SDLC line."
::= { sdlcLSOperEntry 8 }
sdlcLSOperMODULO OBJECT-TYPE
SYNTAX INTEGER { 8, 128}
ACCESS read-write
STATUS mandatory
DESCRIPTION
"This object reflects the current modulus for an SDLC
link station. This modulus determines the size of
rotating acknowledgement window used by the SDLC
link station pair."
DEFVAL { 8 }
::= { sdlcLSOperEntry 9 }
sdlcLSOperRETRIESm OBJECT-TYPE
SYNTAX INTEGER (0..128)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object controls number of retries in a retry
sequence for an SDLC link station. A retry sequence
is a series of retransmitted frames ( data or
control) for which no positive acknowledgement
is received.
The current number of times that the retry sequence
is to be repeated is reflected by the object:
sdlcLSOperRETRIESn. The current interval between
retry sequences is reflected by the object:
sdlcLSOperRETRIESt."
Expires April 13, 1994 [Page 29]
Internet Draft SNADLC MIB October 1993
::= { sdlcLSOperEntry 10 }
sdlcLSOperRETRIESt OBJECT-TYPE
SYNTAX INTEGER (0..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current interval, in
seconds, between retry sequences for an SDLC link
station if multiple retry sequences are specified.
A retry sequence is a series of retransmitted frames
( data or control) for which no positive
acknowledgement is received.
The current number of repeated retries sequences is
reflected by the object: sdlcLSOperRETRIESn.
The current retries per sequence is reflected by the
object: sdlcLSOperRETRIESm."
::= { sdlcLSOperEntry 11 }
sdlcLSOperRETRIESn OBJECT-TYPE
SYNTAX INTEGER (0..127)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current number of times
that a retry sequence is repeated for an SDLC link
station. A retry sequence is a series of
retransmitted frames ( data or control) for which
no positive acknowledgement is received.
The current interval between retry sequences is
reflected by the object: sdlcLSOperRETRIESn.
The current retries per sequence is reflected by
the object: sdlcLSOperRETRIESm."
::= { sdlcLSOperEntry 12 }
sdlcLSOperRNRLIMIT OBJECT-TYPE
SYNTAX INTEGER (1..90)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the current length of time, in
minutes, that an SDLC link station will allow its
adjacent link station to remain in a busy (RNR)
Expires April 13, 1994 [Page 30]
Internet Draft SNADLC MIB October 1993
state before declaring it inoperative."
::= { sdlcLSOperEntry 13 }
sdlcLSOperDATMODE OBJECT-TYPE
SYNTAX INTEGER
{
half(1),
full(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects whether the current
communications mode with the adjacent link station
is two-way-alternate (half) ortwo-way-simultaneous
(full)."
::= { sdlcLSOperEntry 14 }
sdlcLSOperCreateTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the elapsed time, in
1/100ths of seconds, between system initialization
and the creation of this SDLC link station."
::= { sdlcLSOperEntry 15 }
sdlcLSOperLastModifyTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the elapsed time, in
1/100ths of seconds, between system initialization
and the last modification of this SDLC link station.
If the link station has not been modified, then this
value shall be zero."
::= { sdlcLSOperEntry 16 }
sdlcLSOperLastChangeTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
Expires April 13, 1994 [Page 31]
Internet Draft SNADLC MIB October 1993
"This object describes the elapsed time, in
1/100ths of seconds, between system initialization
and the last state change for this SDLC link
station."
::= { sdlcLSOperEntry 17 }
sdlcLSOperLastFailTime OBJECT-TYPE
SYNTAX TimeTicks
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the elapsed time, in
1/100ths of seconds, between system initialization
and the last failure of this SDLC link station. If
the link station has not failed, then this value
shall be zero."
::= { sdlcLSOperEntry 18}
sdlcLSOperLastFailCause OBJECT-TYPE
SYNTAX INTEGER
{
invalid(1),
rxFRMR(2),
txFRMR(3),
noResponse(4),
protocolErr(5),
noActivity(6),
rnrLimit(7),
retriesExpired(8)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This enumerated object reflects the cause of the
last failure of this SDLC link station. If the link
station has not failed, then this value has no
meaning."
::= { sdlcLSOperEntry 19}
sdlcLSOperLastFailCtrlIn OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(2))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the last control octet or octets
Expires April 13, 1994 [Page 32]
Internet Draft SNADLC MIB October 1993
(depending on modulus) received by this SDLC link
station at the time of the last failure. If the link
station has not failed, then this value has no
meaning."
::= { sdlcLSOperEntry 20 }
sdlcLSOperLastFailCtrlOut OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(2))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the last control octet or octets
(depending on modulus) sent by this SDLC link
station at the time of the last failure. If the link
station has not failed, then this value has no
meaning."
::= { sdlcLSOperEntry 21 }
sdlcLSOperLastFailFRMRInfo OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(3))
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the information field of the
FRMR frame if the last failure for this SDLC link
station was as a result of an invalid frame.
Otherwise, this field has no meaning."
::= { sdlcLSOperEntry 22 }
sdlcLSOperLastFailREPLYTOs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object reflects the number of times that the
REPLYTO timer had expired for an SDLC link
station at the time of the last failure. If the link
station has not failed, then this value has no
meaning."
::= { sdlcLSOperEntry 23 }
sdlcLSOperEcho OBJECT-TYPE
SYNTAX INTEGER
{
no(1),
Expires April 13, 1994 [Page 33]
Internet Draft SNADLC MIB October 1993
yes(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object identifies whether the echo bit is
in effect for this particular link station."
DEFVAL { no }
::= { sdlcLSOperEntry 24 }
sdlcLSOperGPoll OBJECT-TYPE
SYNTAX INTEGER (0..254)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This object describes the group poll address
in effect for this link station instance."
DEFVAL { 0 }
::= { sdlcLSOperEntry 14 }
-- *************************************************************
-- * *
-- * THE SDlC LINK STATION STATISTICS TABLE *
-- * *
-- *************************************************************
sdlcLSStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF SdlcLSStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"Each entry in this table contains statistics
for a specific SDLC link station."
::= { sdlcLSGroup 3 }
sdlcLSStatsEntry OBJECT-TYPE
SYNTAX SdlcLSStatsEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTION
"A list of statistics for an SDLC link station."
INDEX { sdlcLSStatsIfIndex, sdlcLSStatsAddress }
::= { sdlcLSStatsTable 1 }
9
9Expires April 13, 1994 [Page 34]
Internet Draft SNADLC MIB October 1993
SdlcLSStatsEntry ::= SEQUENCE
{
sdlcLSStatsIfIndex INTEGER,
sdlcLSStatsAddress INTEGER,
sdlcLSStatsBLUsIn Counter,
sdlcLSStatsBLUsOut Counter,
sdlcLSStatsOctetsIn Counter,
sdlcLSStatsOctetsOut Counter,
sdlcLSStatsPollsIn Counter,
sdlcLSStatsPollsOut Counter,
sdlcLSStatsPollRspIn Counter,
sdlcLSStatsPollRspOut Counter,
sdlcLSStatsLocalBusies Counter,
sdlcLSStatsRemoteBusies Counter,
sdlcLSStatsIFramesIn Counter,
sdlcLSStatsIFramesOut Counter,
sdlcLSStatsRetransmits Counter,
sdlcLSStatsIOctetsIn Counter,
sdlcLSStatsIOctetsOut Counter,
sdlcLSStatsUIFramesIn Counter,
sdlcLSStatsUIFramesOut Counter,
sdlcLSStatsXIDsIn Counter,
sdlcLSStatsXIDsOut Counter,
sdlcLSStatsTESTsIn Counter,
sdlcLSStatsTESTsOut Counter,
sdlcLSStatsREJsIn Counter,
sdlcLSStatsREJsOut Counter,
sdlcLSStatsFRMRsIn Counter,
sdlcLSStatsFRMRsOut Counter,
sdlcLSStatsProtocolErrs Counter,
sdlcLSStatsActivityTOs Counter,
sdlcLSStatsRNRLIMITs Counter,
sdlcLSStatsRetriesExps Counter
}
sdlcLSStatsIfIndex OBJECT-TYPE
SYNTAX INTEGER
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The ifIndex value for the SDLC port which
owns this link station."
::= { sdlcLSStatsEntry 1 }
sdlcLSStatsAddress OBJECT-TYPE
Expires April 13, 1994 [Page 35]
Internet Draft SNADLC MIB October 1993
SYNTAX INTEGER(1..255)
ACCESS read-only
STATUS mandatory
DESCRIPTION
"This value is the poll address of the secondary
link station in this SDLC link. It uniquely
identifies the SDLC link station within a single
SDLC port."
::= { sdlcLSStatsEntry 2 }
sdlcLSStatsBLUsIn OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total basic link units
(BLUs; frames) received from an adjacent SDLC link
station since system startup."
::= { sdlcLSStatsEntry 3}
sdlcLSStatsBLUsOut OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total basic link units
(BLUs; frames), transmitted to an adjacent SDLC
link station since system startup."
::= { sdlcLSStatsEntry 4}
sdlcLSStatsOctetsIn OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total octets received from
an adjacent SDLC link station since system startup."
::= { sdlcLSStatsEntry 5}
sdlcLSStatsOctetsOut OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total octets transmitted to
Expires April 13, 1994 [Page 36]
Internet Draft SNADLC MIB October 1993
an adjacent SDLC link station since system startup."
::= { sdlcLSStatsEntry 6}
sdlcLSStatsPollsIn OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total polls received from
an adjacent SDLC link station since system startup."
::= { sdlcLSStatsEntry 7}
sdlcLSStatsPollsOut OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total polls sent to
an adjacent SDLC link station since system startup."
::= { sdlcLSStatsEntry 8}
sdlcLSStatsPollRspsOut OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total polls responded to
by an adjacent SDLC link station since system startup."
::= { sdlcLSStatsEntry 9}
sdlcLSStatsPollRspsIn OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total polls responded to
by the local SDLC link station since system startup."
::= { sdlcLSStatsEntry 10}
sdlcLSStatsLocalBusies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total number of times that
Expires April 13, 1994 [Page 37]
Internet Draft SNADLC MIB October 1993
the local SDLC link station has entered a busy state
(RNR) since system startup."
::= { sdlcLSStatsEntry 11}
sdlcLSStatsRemoteBusies OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total number of times that
an adjacent ( remote) SDLC link station has entered a
busy state (RNR) since system startup."
::= { sdlcLSStatsEntry 12}
sdlcLSStatsIFramesIn OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total I-frames received
from an adjacent SDLC link station since system
startup."
::= { sdlcLSStatsEntry 13}
sdlcLSStatsIFramesOut OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total I-frames transmitted
to an adjacent SDLC link station since system startup."
::= { sdlcLSStatsEntry 14}
sdlcLSStatsRetransmits OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total frames retransmitted
to an adjacent SDLC link station since system startup."
::= { sdlcLSStatsEntry 15}
sdlcLSStatsIOctetsIn OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
Expires April 13, 1994 [Page 38]
Internet Draft SNADLC MIB October 1993
STATUS mandatory
DESRIPTION
"This object reflects the total octets contained in
I-frames received from an adjacent SDLC link station
since system startup."
::= { sdlcLSStatsEntry 16}
sdlcLSStatsIOctetsOut OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total octets contained in
I-frames transmitted to an adjacent SDLC link station
since system startup."
::= { sdlcLSStatsEntry 17}
sdlcLSStatsUIFramesIn OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total UI-frames received
from an adjacent SDLC link station since system
startup."
::= { sdlcLSStatsEntry 18}
sdlcLSStatsUIFramesOut OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total UI-frames transmitted
to an adjacent SDLC link station since system startup."
::= { sdlcLSStatsEntry 19}
sdlcLSStatsXIDsIn OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total XID frames received
from an adjacent SDLC link station since system
startup."
::= { sdlcLSStatsEntry 20}
Expires April 13, 1994 [Page 39]
Internet Draft SNADLC MIB October 1993
sdlcLSStatsXIDsOut OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total XID frames transmitted
to an adjacent SDLC link station since system startup."
::= { sdlcLSStatsEntry 21}
sdlcLSStatsTESTsIn OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total TEST frames, commands
or responses, received from an adjacent SDLC link
station since system startup."
::= { sdlcLSStatsEntry 22}
sdlcLSStatsTESTsOut OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total TEST frames, commands or
responses, transmitted to an adjacent SDLC link station
since system startup."
::= { sdlcLSStatsEntry 23}
sdlcLSStatsREJsIn OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total REJ frames received
from an adjacent SDLC link station since system
startup."
::= { sdlcLSStatsEntry 24}
sdlcLSStatsREJsOut OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
Expires April 13, 1994 [Page 40]
Internet Draft SNADLC MIB October 1993
"This object reflects the total REJ frames transmitted
to an adjacent SDLC link station since system startup."
::= { sdlcLSStatsEntry 25}
sdlcLSStatsFRMRsIn OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total frame reject (FRMR)
frames received from an adjacent SDLC link station
since system startup."
::= { sdlcLSStatsEntry 26}
sdlcLSStatsFRMRsOut OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total frame reject (FRMR)
frames transmitted to an adjacent SDLC link station
since system startup."
::= { sdlcLSStatsEntry 27}
sdlcLSStatsProtocolErrs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total occurrences, since
startup, where this SDLC link station has inactivated
the link as a result of receiving a frame from its
adjacent link station which was in violation of the
protocol."
::= { sdlcLSStatsEntry 28}
sdlcLSStatsActivityTOs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total occurrences, since
startup, where this SDLC link station has inactivated
the link as a result of no activity on the link.
Expires April 13, 1994 [Page 41]
Internet Draft SNADLC MIB October 1993
Implementation of this object is optional."
::= { sdlcLSStatsEntry 29}
sdlcLSStatsRNRLIMITs OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total occurrences, since
startup, where this SDLC link station has inactivated
the link as a result of its RNRLIMIT timer expiring."
::= { sdlcLSStatsEntry 30}
sdlcLSStatsRetriesExps OBJECT-TYPE
SYNTAX Counter
ACCESS read-only
STATUS mandatory
DESRIPTION
"This object reflects the total occurrences, since
startup, where this SDLC link station has inactivated
the link as a result of a retry sequence being
exhausted."
::= { sdlcLSStatsEntry 31}
--
-- TRAP DEFINITIONS
--
sdlcPortStatusChange TRAP-TYPE
ENTERPRISE sdlc
VARIABLES { sdlcPortOperIfIndex,
sdlcPortOperState,
sdlcPortAdminState,
sdlcPortOperLastFailTime,
sdlcPortOperLastFailCause
}
DESCRIPTION
"This trap indicates that the state of an SDLC port
has transitioned to active or inactive."
::= 1
sdlcLSStatusChange TRAP-TYPE
ENTERPRISE sdlc
VARIABLES { sdlcLSOperIfIndex,
sdlcLSOperAddress
Expires April 13, 1994 [Page 42]
Internet Draft SNADLC MIB October 1993
sdlcLSOperState,
sdlcLSAdminState,
sdlcLSOperLastFailTime,
sdlcLSOperLastFailCause,
sdlcLSOperLastFailFRMRInfo,
sdlcLSOperLastFailCtrlIn,
sdlcLSOperLastFailCtrlOut,
sdlcLSOperLastFailREPLYTOs
}
DESCRIPTION
"This trap indicates that the state of an SDLC link
station has transitioned to contacted or
discontacted."
::= 2
END
LAST-UPDATED "931013"
ORGANIZATION "IETF SNA DLC MIB Working Group"
CONTACT-INFO
" Wayne Clark
Postal: Cisco Systems, Inc.
1525 O'Brien Drive
Menlo Park, CA 94025
Tel: 415 688 4627
Fax: 415 688 4575
E-mail: wclark@cisco.com
DESCRIPTION
"The MIB module for SNA Data Link Control"
::= { experimental xx }
SNA-DLC-MIBObjects OBJECT IDENTIFIER ::= { SNADLCMIB 1 }
9
9Expires April 13, 1994 [Page 43]
Internet Draft SNADLC MIB October 1993
6. Acknowledgements
Thanks goes to the SNADLC MIB working group for reviewing this
MIB and for their infinite patience through the editing
process.
9
9Expires April 13, 1994 [Page 44]
Internet Draft SNADLC MIB October 1993
7. References
[1] B. Stewart, "Definitions of Managed Objects for RS-232-
like Hardware Devices", Request for Comments 1317, April
1992.
9
9Expires April 13, 1994 [Page 45]
Internet Draft SNADLC MIB October 1993
8. Security Considerations
Security issues are not discussed in this memo.
9. Author's Address
Jeff Hilgeman (chair)
Apertus Technologies, Inc.
7275 Flying Cloud Dr.
Eden Prarie, MN 55344
Phone: 612/828-0668
Email: jeffh@apertus.com
Shannon D. Nix
Netlink, Inc.
3214 Spring Forest Rd.
Raleigh, NC 27604
Phone: 919/878-8612
Email: sdn@netlink.com
Alan Bartkey
Sync Research, Inc.
7 Studebaker
Irvine, CA 92718
Phone: 714/588-2070
Email: alan@sync.com
Wayne Clark (editor)
cisco Systems, Inc.
1525 O'Brien Dr.
Menlo Park, CA 94025
Phone: 415/688-4627
Email: wclark@cisco.com
9
9Expires April 13, 1994 [Page 46]
Internet Draft SNADLC MIB October 1993
Table of Contents
1 Status of this Memo ................................... 1
2 Abstract .............................................. 2
3 The SNMPv2 Network Management Framework ............... 3
3.1 Object Definitions .................................. 3
4 Overview .............................................. 4
5 Definitions ........................................... 5
6 Acknowledgements ...................................... 44
7 References ............................................ 45
8 Security Considerations ............................... 46
9 Author's Address ...................................... 46
9
9Expires April 13, 1994 [Page 47]