Internet DRAFT - draft-irtf-dtnrg-dtnmp
draft-irtf-dtnrg-dtnmp
Delay-Tolerant Networking Research Group E. Birrane
Internet-Draft V. Ramachandran
Intended status: Experimental Johns Hopkins Applied Physics Laboratory
Expires: July 4, 2015 December 31, 2014
Delay Tolerant Network Management Protocol
draft-irtf-dtnrg-dtnmp-01
Abstract
This draft describes the Delay/Disruption Tolerant Network Management
Protocol (DTNMP). The DTNMP provides monitoring and configuration
services between managing devices and managed devices, some of which
may operate on the far side of high-delay or high-disruption links.
The protocol is designed to minimize the number of transmitted bytes,
to operate without sessions or (concurrent) two-way links, and to
function autonomously when there is no timely contact with a network
operator.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on July 4, 2015.
Copyright Notice
Copyright (c) 2014 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
Birrane & Ramachandran Expires July 4, 2015 [Page 1]
Internet-Draft DTNMP December 2014
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2. Technical Notes . . . . . . . . . . . . . . . . . . . . . 4
1.3. Scope . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3.1. Protocol Scope . . . . . . . . . . . . . . . . . . . 5
1.3.2. Specification Scope . . . . . . . . . . . . . . . . . 5
1.4. Requirements Language . . . . . . . . . . . . . . . . . . 5
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. System Model . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2. Roles and Responsibilities . . . . . . . . . . . . . . . 8
3.3. Data Flows . . . . . . . . . . . . . . . . . . . . . . . 10
3.4. Control Flow by Role . . . . . . . . . . . . . . . . . . 11
3.4.1. Notation . . . . . . . . . . . . . . . . . . . . . . 11
3.4.2. Serialized Management . . . . . . . . . . . . . . . . 11
3.4.3. Multiplexed Management . . . . . . . . . . . . . . . 12
3.4.4. Data Fusion . . . . . . . . . . . . . . . . . . . . . 14
4. Component Model . . . . . . . . . . . . . . . . . . . . . . . 15
4.1. Data Representation . . . . . . . . . . . . . . . . . . . 15
4.1.1. Types . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1.2. Categories . . . . . . . . . . . . . . . . . . . . . 15
4.1.3. Data Model . . . . . . . . . . . . . . . . . . . . . 16
4.2. Primitive Types . . . . . . . . . . . . . . . . . . . . . 17
4.2.1. Self-Delimiting Numeric Value (SDNV) . . . . . . . . 17
4.2.2. Timestamp (TS) . . . . . . . . . . . . . . . . . . . 17
4.2.3. Data Collections (DC) . . . . . . . . . . . . . . . . 17
4.3. Naming and Identification . . . . . . . . . . . . . . . . 17
4.4. Special Types . . . . . . . . . . . . . . . . . . . . . . 21
4.4.1. MID Collections (MC) . . . . . . . . . . . . . . . . 21
4.4.2. Expressions (EXPR) . . . . . . . . . . . . . . . . . 21
4.4.3. Predicate (PRED) . . . . . . . . . . . . . . . . . . 22
5. Functional Specification . . . . . . . . . . . . . . . . . . 22
5.1. Message Group Format . . . . . . . . . . . . . . . . . . 23
5.2. Message Format . . . . . . . . . . . . . . . . . . . . . 24
5.3. Register Agent (0x00) . . . . . . . . . . . . . . . . . . 25
5.4. Data Report (0x12) . . . . . . . . . . . . . . . . . . . 26
5.5. Perform Control (0x20) . . . . . . . . . . . . . . . . . 26
6. Appliation Data Model Template . . . . . . . . . . . . . . . 27
6.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . 27
6.2. ADM Types . . . . . . . . . . . . . . . . . . . . . . . . 27
6.3. Template . . . . . . . . . . . . . . . . . . . . . . . . 28
6.3.1. ADM Metadata . . . . . . . . . . . . . . . . . . . . 29
Birrane & Ramachandran Expires July 4, 2015 [Page 2]
Internet-Draft DTNMP December 2014
6.3.2. ADM Information Capture . . . . . . . . . . . . . . . 29
7. DTNMP Agent Application Data Model . . . . . . . . . . . . . 30
7.1. Data Definitions . . . . . . . . . . . . . . . . . . . . 30
7.2. Metadata Definitions . . . . . . . . . . . . . . . . . . 31
7.3. Data Definitions . . . . . . . . . . . . . . . . . . . . 31
7.3.1. Atomic Data . . . . . . . . . . . . . . . . . . . . . 31
7.3.2. Computed Data . . . . . . . . . . . . . . . . . . . . 32
7.3.3. Reports . . . . . . . . . . . . . . . . . . . . . . . 32
7.4. Operators . . . . . . . . . . . . . . . . . . . . . . . . 33
7.5. Controls . . . . . . . . . . . . . . . . . . . . . . . . 35
7.5.1. Control Summary . . . . . . . . . . . . . . . . . . . 35
7.5.2. Control Specification . . . . . . . . . . . . . . . . 37
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 55
9. Security Considerations . . . . . . . . . . . . . . . . . . . 55
10. Normative References . . . . . . . . . . . . . . . . . . . . 55
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 55
1. Introduction
This document presents the Delay/Disruption Tolerant Network
Management Protocol (DTNMP) providing application-layer network
management services over links where propagation delays or link
disruptions prevent timely communications between a network operator
and a managed device.[RFC4838].
1.1. Overview
A network management protocol defines the messages that implement
management functions amongst managed and managing devices in a
network. Management functions include the definition, production,
and reporting of performance data, the application of administrative
and security policy, and the configuration of behavior based on local
time and state measurements.
DTNs contain nodes whose communication links are characterized by
signal propagation delays and/or transmission disruptions that make
timely data exchange difficult or impossible. Management protocols
that rely on timely data exchange, such as those that rely on
negotiated sessions or other synchronized acknowledgment, do not
function in the DTN environment. For example, the Internet approach
of network management via closed-loop, synchronous messaging does not
work when network disruptions increase in frequency and severity.
While no protocol delivers data in the absence of a networking link,
protocols that eliminate or drastically reduce overhead and end-point
coordination require smaller transmission windows and continue to
function when confronted with scaling delays and disruptions in the
network.
Birrane & Ramachandran Expires July 4, 2015 [Page 3]
Internet-Draft DTNMP December 2014
DTNMP accomplishes the network management function using open-loop,
intelligent-push, asynchronous mechanisms that better scale as link
challenges scale. The protocol is designed to support five desirable
properties:
Intelligent Push of Information
The intelligent push of information eliminates the need for round-
trip data exchange in the management protocol. This is a
necessary consequence of operating in open-loop systems where
reliable round-trip communication may not exist. DTNMP is
designed to operate even in uni-directional networks.
Small Message Sizes
Smaller messages require smaller periods of viable transmission
for communication, incur less re-transmission cost, and consume
less resources when persistently stored en-route in the network.
DTNMP minimizes the size of a message whenever practical, to
include packing and unpacking binary data, variable-length fields,
and pre-configured data definitions.
Fine-grained, Flexible Data Identification
Fine-grained identification allows data in the system to be
explicitly addressed while flexible data identification allows
users to define their own customized, addressed data collections.
In both cases, the ability to define precisely the data required
removes the need to query and transmit large data sets only to
filter/downselect desired data at a receiving device.
Asynchronous Operation
DTNMP does not rely on session establishment or round-trip data
exchange to perform network management functions. Wherever
possible, the DTNMP is designed to be stateless. Where state is
required, the DTNMP provides mechanisms to support transactions
and graceful degredation when nodes in the network fail to
synchronize on common definitions.
Compatibility with Low-Latency Network Management Protocols
DTNMP adopts an identifier approach compatible with the Managed
Information Base (MIB) format used by Internet management
protocols such as the Simple Network Management Protocol (SNMP),
thus enabling management interfaces between DTNs and other types
of networks.
1.2. Technical Notes
All multi-byte values are assumed to be communicated in network-byte
order. Bit-fields are specified in Little-Endian format with bit
Birrane & Ramachandran Expires July 4, 2015 [Page 4]
Internet-Draft DTNMP December 2014
position 0 holding the least-significant bit (LSB). When illustrated
in this manuscript, the LSB appears on the right.
1.3. Scope
1.3.1. Protocol Scope
The DTNMP provides data monitoring, administration, and configuration
for applications operating above the data link layer of the OSI
networking model. While the DTNMP may be configured to support the
management of network layer protocols (such as the Internet Protocol
and Bundle Protocol) it also uses these protocols stacks to
encapsulate and communicate its own DTNMP messages.
It is assumed that the protocols used to carry DTNMP messages provide
addressing, confidentiality, integrity, security, fragmentation
support and other network/session layer functions. Therefore, these
items are not discussed in the scope of this document.
1.3.2. Specification Scope
This document describes the format of the DTNMP messages exchanged
amongst managing and managed devices in a DTN. This document further
describes the rationale behind key design decisions to the extent
that such a description informs the operational deployment and
configuration of DTNMP implementations. This document does not
address specific data configurations of DTNMP-enabled devices, nor
does it discuss the interface between DTNMP and other management
protocols, such as SNMP.
1.4. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. Terminology
This section identifies those terms critical to understanding the
proper operation of the DTNMP. Whenever possible, these terms align
in both word selection and meaning with their analogs from other
management protocols.
Actor
A software service running on either managed or managing
devices implementing an end-point in the DTNMP. Actors may
implement the "Manager" role, "Agent" role, or both.
Birrane & Ramachandran Expires July 4, 2015 [Page 5]
Internet-Draft DTNMP December 2014
Agent Role
A role within the DTNMP, associated with a managed device,
responsible for reporting performance data, enforcing
administrative policies, and accepting/performing actions.
Agents exchange information with DTNMP managers operating
either on the same device or on a remote managing device.
Application Data Model (ADM)
The set of predefined data definitions, reports, literals,
operations, and controls given to a DTNMP actor to manage a
particular application or protocol. DTNMP actors support
multiple ADMs, one for each application/protocol being
managed.
Atomic Data
Globally unique, managed data definitions, similar to those
defined in a Management Information Base (MIB), whose
definition does not change based on the configuration of a
DTNMP actor. Atomic data comprise the "lingua franca" within
the DTNMP. All messages in the protocol operate either
directly on atomic data or on data derived from atomic data.
Computed Data
Data items that are computed dynamically by a DTNMP actor
from some combination of Atomic Data and other Computed Data.
Controls
Operations that may be undertaken by a DTNMP actor to change
the behavior, configuration, or state of an application
managed by the DTNMP.
Macros
A named, ordered collection of controls.
Managed Item Definition (MID)
A parameterized structure used to uniquely identify all data
and control definitions within the DTNMP. MIDs are a super-
set of Object Identifiers (OIDs) and the mechanism by which
the DTNMP maintains data compatibility with other management
protocols.
Manager
A role within the DTNMP associated with a managing device
responsible for configuring the behavior of, and
receiving/processing/visualizing information from, DTNMP
agents. DTNMP managers also provide gateways to non-DTNMP
management protocols as part of conditioning the data
returned from agents. Managers interact with one or more
Birrane & Ramachandran Expires July 4, 2015 [Page 6]
Internet-Draft DTNMP December 2014
agents located on the same device and/or on remote devices in
the network.
Report
A named, ordered collection of data items gathered by one or
more DTNMP agents and provided to one or more DTNMP managers.
Reports may contain atomic data, computed data, and other
reports. Individual data within a report are not named; the
report itself is named to reduce the size of the report
message.
3. System Model
3.1. Overview
DTNMP performs the core network management functions of
configuration, performance reporting, control, and administration, as
follows.
Configuration
The configuration function synchronizes definitions amongst
DTNMP actors in the DTN. Managers and Agents must agree on
what ADMs are supported by what nodes. Further, these Actors
must agree on the definitions of customized information, such
as data production schedules, report definitions, and state-
based autonomous actions.
Performance Reporting
Since DTNMP operates asynchronously, performance *monitoring*
is replaced by performance *reporting*. As there is no
expectation of closed-loop control of a managed device across
a delayed/disrupted link, the best action that a managing
device can undertake is to collect and operate on whatever
data is received by managed devices.
Reporting the performance of a managed device involves the
local collection of reports and the communication of those
reports to appropriate managing devices.
Control
Part of the ADM for a supported application/protocol includes
a list of controls/commands that may be run by a DTNMP actor
based on local time or local state. Controls comprise the
basic autonomy mechanism within the DTNMP.
Administration
The mappings amongst agents and managers within a network may
be complex, especially in networks comprising multiple
administrative domains. The administrative management
Birrane & Ramachandran Expires July 4, 2015 [Page 7]
Internet-Draft DTNMP December 2014
function defines what managers may control what agents, for
what types of information.
3.2. Roles and Responsibilities
By definition, DTNMP agents reside on managed devices and DTNMP
managers reside on managing devices. These roles naturally map to
the transmit and receipt of various DTNMP messages. This section
describes how each of these roles participate in the network
management functions outlined in the prior section.
Agent Responsibilities
Local Data Collection
Agents MUST collect and report the data defined in
all ADMs for which they have been configured for the
local managed device. Agents MAY also collect data
for network nodes that do not have their own DTNMP
agents. In this scenario, the DTNMP agent acts as a
proxy agent.
Autonomous Control
Agents MUST determine, without manager intervention,
whether a configured control should be invoked.
Agents MUST periodically evaluate the conditions
associated with configured controls and invoke those
controls based on local state. Agents MAY also
invoke controls on other devices within a regional,
low-latency network.
Data Conditioning
DTNMP agents MUST accept computed data definitions
that specify how a single data value may be
constructed from the transformation of one or more
other data values in the system, using the expression
syntax specified in this manuscript. Further, agents
MUST produce this data when requested by Managers
with the appropriate security persmissions. Agents
MUST produce the list of computer data definitions
when requested by a Manager. Agents MUST detect when
a computed data definition references other data
definitions that are unknown to the agent and respond
in a way consistent with the logging/error-handling
configuration of the agent.
Report Definition
Agents MUST support the ability to accept and store
definitions for custom report definitions. Agents
Birrane & Ramachandran Expires July 4, 2015 [Page 8]
Internet-Draft DTNMP December 2014
MUST conform to the security policies associated with
custom reports when determining if a Manager may
request a report defined by a different Manager in
the network. Agents MUST provide a listing of custom
report definitions to appropriate managing devices
when requested. Agents MUST detect requests for
custom reports that are not configured on the agent,
or are not appropriate for the requesting Manager,
and respond in a way consistent with the logging/
error-handling configuration of the agent.
Consolidate Messages
Agents SHOULD produce as few messages as possible
when sending information. For example, rather than
sending multiple report messages to a manager, an
agent SHOULD prefer to send a single message
containing multiple reports.
Regional Proxy
Agents MAY perform any of their responsibilities on
behalf of other network nodes that, themselves, do
not have a DTNMP agent. In such a configuration, the
DTNMP agent acts as a proxy agent for these other
network nodes.
Manager Responsibilities
Agent/ADM Mapping
Managers MUST understand what ADMs are supported by
the various agents with which they communicate.
Managers SHOULD NOT attempt to request, invoke, or
refer to ADM information for ADMs unsupported by an
agent.
Data Collection
Managers MUST receive information from agents by
asynchronously configuring the production of data
reports and then waiting for, and collecting,
responses from agents over time. Managers SHOULD
implement internal time-outs to detect conditions
where agent information has not been received within
network-specific timespans.
Custom Definitions
Managers SHOULD provide the ability to define custom
data and report definitions. Any defined custom
definitions MUST be transmitted to appropriate agents
and these definitions MUST be remembered to interpret
Birrane & Ramachandran Expires July 4, 2015 [Page 9]
Internet-Draft DTNMP December 2014
the reporting of these custom values from an agent in
the future.
Data Translation
Managers SHOULD provide some interface to other
network management protocols, such as the SNMP.
Managers MAY accomplish this by accumulating a
repository of push-data from high-latency parts of
the network from which data may be pulled by low-
latency parts of the network.
Data Fusion
Managers MAY support the fusion of data from multiple
agents with the purpose of transmitting fused data
results to other managers within the network.
Managers MAY receive fused reports from other
managers pursuant to appropriate security and
administrative configurations.
3.3. Data Flows
We identify three significant data flows within the DTNMP: control
flows from managers to agents, reports flows from agents to managers,
and fusion reports from managers to other managers. These data flows
are illustrated in Figure 1.
DTNMP Data Flows
+---------+ +------------------------+ +---------+
| Node A | | Node B | | Node C |
| | | | | |
|+-------+| |+-------+ +-------+| |+-------+|
|| ||=====>>|| DTNMP |====>>| DTNMP ||====>>|| ||
|| ||<<=====|| Mgr B |<<====|Agent B||<<====|| ||
|| DTNMP || |+--++---+ +-------+| || DTNMP ||
|| Agent || +---||-------------------+ || Mgr C ||
|| A || || || ||
|| ||<<=========||==========================|| ||
|| ||===========++========================>>|| ||
|+-------+| |+-------+|
+---------+ +---------+
Figure 1
In this data flow, the agent on node A receives configurations from
managers on nodes B and C, and replies with reports back to these
managers. Similarly, the agent on node B interacts with the local
manager on node B and the remote manager on node C. Finally, the
Birrane & Ramachandran Expires July 4, 2015 [Page 10]
Internet-Draft DTNMP December 2014
manager on node B may fuse data reports received from agents at nodes
A and B and send these fused reports back to the manager on node C.
From this figure, we see many-to-many relationships amongst managers,
amongst agents, and between agents and managers. Note that agents
and managers are roles, not necessarily differing software
applications. Node A may represent a single software application
fulfilling only the agent role, whereas node B may have a single
software application fulfilling both the agent and manager roles.
The specifics of how these roles are realized is an implementation
matter.
3.4. Control Flow by Role
This section describes three common configurations of DTNMP agents
and managers and the flow of messages between them. These
configurations involve local and remote management and data fusion.
3.4.1. Notation
The notation outlined in Table 1 describes the types of control
messages exchanged between DTNMP agents and managers.
+-------------+---------------------------------------+-------------+
| Term | Definition | Example |
+-------------+---------------------------------------+-------------+
| AD# | Atomic data definition, from ADM. | AD1 |
| | | |
| CD# | Custom data definition. | CD1 = AD1 + |
| | | CD0. |
| | | |
| DEF([ACL], | Define id from expression. Allow | DEF([*], |
| ID,EXPR) | managers in access control list (ACL) | CD1, AD1 + |
| | to request this id. | AD2) |
| | | |
| PROD(P,ID) | Produce ID according to predicate P. | PROD(1s, |
| | P may be a time period (1s) or an | AD1) |
| | expression (AD1 > 10). | |
| | | |
| RPT(ID) | A report identified by ID. | RPT(AD1) |
+-------------+---------------------------------------+-------------+
Table 1: Terminology
3.4.2. Serialized Management
This is a nominal configuration of network management where a
managing device interacts with a set of managed devices, with a DTNMP
manager installed on the managing device and a DTNMP agent installed
Birrane & Ramachandran Expires July 4, 2015 [Page 11]
Internet-Draft DTNMP December 2014
on each managed device. The control flows for this are outlined in
Figure 2.
Serialized Management Control Flow
+----------+ +---------+ +---------+
| Manager | | Agent A | | Agent B |
+----+-----+ +----+----+ +----+----+
| | |
|-----PROD(1s, AD1)---->| |(Step 1)
|----------------------------PROD(1s, AD1)--->|
| | |
| | |
|<-------RPT(AD1)-------| |(Step 2)
|<-----------------------------RPT(AD1)-------|
| | |
| | |
|<-------RPT(AD1)-------| |
|<-----------------------------RPT(AD1)-------|
| | |
| | |
|<-------RPT(AD1)-------| |
|<-----------------------------RPT(AD1)-------|
| | |
In a simple network, a manager interacts with multiple agents.
Figure 2
In this figure, the manager configures agents A and B to produce
atomic data AD1 every second in (Step 1). At some point in the
future, upon receiving and configuring this message, agents A and B
then build a report containing AD1 and send those reports back to the
manager in (Step 2).
3.4.3. Multiplexed Management
Networks spanning multiple administrative domains may require
multiple managing devices (for example, one per domain). When a
manager defines custom reports/data to an agent, that definition may
be tagged with an access control list (ACL) to limit what other
managers will be privy to this information. Managers in such
networks SHOULD synchronize with those other managers granted access
to their custom data definitions. When agents generate messages,
they MUST only send messages to managers according to these ACLs, if
present. The control flows in this scenario are outlined in
Figure 3.
Birrane & Ramachandran Expires July 4, 2015 [Page 12]
Internet-Draft DTNMP December 2014
Multiplexed Management Control Flow
+-----------+ +-------+ +-----------+
| Manager A | | Agent | | Manager B |
+-----+-----+ +---+---+ +-----+-----+
| | |
|--DEF(A,CD1,AD1*2)--->|<--DEF(B, CD2, AD2*2)-|(Step 1)
| | |
|---PROD(1s, CD1)----->|<---PROD(1s, CD2)-----|(Step 2)
| | |
|<-------RPT(CD1)------| |(Step 3)
| |--------RPT(CD2)----->|
|<-------RPT(CD1)------| |
| |--------RPT(CD2)----->|
| | |
| |<---PROD(1s, CD1)-----|(Step 4)
| | |
| |--ERR(CD1 no perm.)-->|
| | |
|--DEF(*,CD3,AD3*3)--->| |(Step 5)
| | |
|---PROD(1s, CD3)----->| |(Step 6)
| | |
| |<---PROD(1s, CD3)-----|
| | |
|<-------RPT(CD3)------|--------RPT(CD3)----->|(Step 7)
|<-------RPT(CD1)------| |
| |--------RPT(CD2)----->|
|<-------RPT(CD3)------|--------RPT(CD3)----->|
|<-------RPT(CD1)------| |
| |--------RPT(CD2)----->|
Complex networks require multiple managers interfacing with agents.
Figure 3
In more complex networks, managers may choose to define custom
reports and data definitions, and agents may need to accept such
definitions from multiple managers. Custom data definitions may
include an ACL that describes who may query and otherwise understand
the custom definition. In (Step 1), Manager A defines CD1 only for A
while Manager B defines CD2 only for B. Managers may, then, request
the production of reports containing these custom definitions, as
shown in (Step 2). Agents produce different data for different
managers in accordance with configured production rules, as shown in
(Step 3). If a manager requests an operation, such as a production
rule, for a custom data definition for which the manager has no
permissions, a response consistent with the configured logging policy
Birrane & Ramachandran Expires July 4, 2015 [Page 13]
Internet-Draft DTNMP December 2014
on the agent should be implemented, as shown in (Step 4).
Alternatively, as shown in (Step 5), a manager may define custom data
with no restrictions allowing all other managers to request and use
this definition. This allows all managers to request the production
of reports containing this definition, shown in (Step 6) and have all
managers receive this and other data going forward, as shown in (Step
7).
3.4.4. Data Fusion
In many networks, agents do not want to individually transmit their
data to a manager, preferring instead to fuse reporting data with
local nodes prior to transmission. This approach reduces the number
and size of messages in the network and reduces overall transmission
energy expenditure. DTNMP supports fusion of NM reports by co-
locating agents and managers on managed devices and offloading fusion
activities to the manager. This process is illustrated in Figure 4.
Data Fusion Control Flow
+-----------+ +-----------+ +---------+ +---------+
| Manager A | | Manager B | | Agent B | | Agent C |
+---+-------+ +-----+-----+ +----+----+ +----+----+
| | | |
|--DEF(A,CD0,AD1+AD2)->| | |(Step 1)
|--PROD(AD1&AD2, CD0)->| | |
| | | |
| |--PROD(1s,AD1)-->| |(Step 2)
| |-------------------PROD(1s, AD2)->|
| | | |
| |<---RPT(AD1)-----| |(Step 3)
| |<-------------------RPT(AD2)------|
| | | |
|<-----RPT(A,CD0)------| | |(Step 4)
| | | |
Data fusion in DTNMP accours amongst managers in the network.
Figure 4
In this example, Manager A requires the production of a computed data
set, CD0, from node B, as shown in (Step 1). The manager role
understands what data is available from what agents in the subnetwork
local to B, understanding that AD1 is available locally and AD2 is
available remotely. Production messages are produced in (Step 2) and
data collected in (Step 3). This allows the manager at node B to
fuse the collected data reports into CD0 and return it in (Step 4).
While a trivial example, the mechanism of associating fusion with the
Birrane & Ramachandran Expires July 4, 2015 [Page 14]
Internet-Draft DTNMP December 2014
manager function rather than the agent function scales with fusion
complexity, though it is important to reiterate that agent and
manager designations are roles, not individual software components.
There may be a single software application running on node B
implementing both Manager B and Agent B roles.
4. Component Model
This section identifies the components that comprise the data
communicated within the DTNMP, the way in which these components are
named, and those special types associated with DTNMP messages.
4.1. Data Representation
4.1.1. Types
Components within the DTNMP are represented as one of four basic data
types: Data, Controls, Literals, and Operators:
Data Data consist of values collected by an agent and reported to
managers within the DTNMP. This includes definitions from an
ADM, derived data as configured from managers, and reports
which are collections of data elements.
Controls Controls consist of actions that may be invoked on agents
and managers to change behavior in response to some external
event (such as local state changes or time). Controls
include application-specific functions specified as part of
an ADM and macros which are collections of these controls.
Literals Literals are constant numerical values that may be used in
the evaluation of expressions and predicates.
Operator Operators are those mathematical functions that operate on
series of Data and Literals, such as addition, subtraction,
multiplication, and division.
4.1.2. Categories
Components within the DTNMP can be categorized as Atomic, Computed,
or Collection.
Atomic
Atomic components are those components that are directly
implemented by the underlying software/firmware of a network
node. Atomic components may also refer to components whose
definitions may not be changed. Examples of atomic
components are Data, Controls, Literals, and Operators
Birrane & Ramachandran Expires July 4, 2015 [Page 15]
Internet-Draft DTNMP December 2014
specified by an ADM. Atomic component identifiers MUST be
unique and SHOULD be managed by a registration authority,
similar to the mechanisms used to assign Object Identifiers
(OIDs). Atomic components must be understood by both DTNMP
managers and agents in a network.
Computed
Computed components are those components that are not
directly implemented by the underlying software/firmware of a
network node. The definition of a computed component MAY be
dynamically defined by DTNMP managers and communicated to one
or more DTNMP agents in a network. The definition of a
computed component may include other computed components or
other atomic components. The identifier of a computed
component is not guaranteed to be universally unique but
SHOULD be unique within the context of a particular network
or internetwork.
Collection
A collection component is a set of other components (to
include other collection components). DTNMP implementations
MUST prevent circular definitions when implementing
collections that include other collections.
4.1.3. Data Model
Each component of the DTNMP data model can be identified as a
combination of type and category, as illustrated in Table 2. In this
table type/catgory combinations that are unsupported are listed as N/
A. Specifically, DTNMP does not support user-defined controls,
constants, or operations; any value that specifies action on an agent
MUST be pre-configured as part of an ADM.
+------------+------------------+----------+----------+----------+
| | Data | Controls | Literals | Operator |
+------------+------------------+----------+----------+----------+
| Atomic | Measured Value | Control | Constant | Operator |
| | | | | |
| Computed | Calculated Value | N/A | N/A | N/A |
| | | | | |
| Collection | Report | Macro | N/A | N/A |
+------------+------------------+----------+----------+----------+
Table 2
Birrane & Ramachandran Expires July 4, 2015 [Page 16]
Internet-Draft DTNMP December 2014
4.2. Primitive Types
4.2.1. Self-Delimiting Numeric Value (SDNV)
The data type "SDNV" refers to a Self-Delimiting Numerical Value
(SDNV) described in [RFC6256]. SDNVs are used in the DTNMP to
capture any data items that are expected to be 8 bytes or less in
total length. DTNMP actors MAY reject any SDNV value that is greater
than 8 bytes in length.
4.2.2. Timestamp (TS)
For compatibility with a variety of protocols, the use of UTC time is
selected to represent all time values in the DTNMP. However,
timestamps in DTNMP may represent either absolute or relative time
based on the associated epoch. DTNMP uses September 9th, 2012 as the
timestamp epoch (UTC time 1348025776). Values less than this value
MUST be considered as relative times. Values greater than or equal
to this epoch MUST be considered as absolute times. In all cases,
the DTNMP timestamp is encoded as an SDNV.
4.2.3. Data Collections (DC)
A Data collection is comprised of a value identifiying the number of
bytes in the collection, followed by each byte, as illustrated in
Figure 5. Data collections are used in the DTNMP to capture variable
data sets that are too large to place in an SDNV.
Data Collection
+---------+--------+--------+ +--------+
| # Bytes | BYTE 1 | BYTE 2 | ... | BYTE N |
| [SDNV] | [BYTE] | [BYTE] | | [BYTE] |
+---------+--------+--------+ +--------+
Figure 5
4.3. Naming and Identification
While all components within the DTNMP can be uniquely identified by
an Object Identifier (OID), several annotations exist to assist with
the filtering and access control associated with components beyond
what is efficiently represented in the OID structure. These
annotations include the type and category of the component, an
optional identifier naming the issuer of the component, and an
optional tag value holding issuer-specific information about the
component.
Birrane & Ramachandran Expires July 4, 2015 [Page 17]
Internet-Draft DTNMP December 2014
The DTNMP Managed Identifier (MID) provides a single, variable length
structure that encapsulates all of the information necessary to
identify a DTNMP component and its useful annotations.
The MID structure, illustrated in Figure 6, is comprised of up to
four fields. In this illustration, each field is named, the type of
each field is given in []'s, and the string "(opt.)" indicates that
the field is optional, pending on the values found in the flags byte.
MID format
+--------+--------+--------+--------+
| Flags | Issuer | OID | Tag |
| [BYTE] | [SDNV] |[VARIED]| [SDNV] |
| | (opt.) | | (opt.) |
+--------+--------+--------+--------+
Figure 6
The MID fields are defined as follows.
Flags
Flags are used to describe the type of component identified
by the MID, identify which optional fields in the MID are
present, and the encoding used to capture the component's
OID. The layout of the flag byte is illustrated in Figure 7.
MID Flag Format
+-----+---+---+-----+------+
| OID |TAG|ISS| CAT | TYPE |
+-----+---+---+-----+------+
| 7 6 | 5 | 4 | 3 2 | 1 0 |
+-----+---+---+-----+------+
MSB LSB
Figure 7
MID Type (TYPE)
The type of the component encapsulated by the MID,
enumerated as data (0), control (1), literal (2), or
operator (3).
MID Category (CAT)
The category of the component encapsulated by the
MID, enumerated as atomic (0), computed (1), and
collection (2).
Birrane & Ramachandran Expires July 4, 2015 [Page 18]
Internet-Draft DTNMP December 2014
Issuer Present (ISS)
Whether the issuer field is present (1) or not (0)
for this MID. If this flag has a value of 1 then the
issuer field MUST be present in the MID. Otherwise,
the issuer field MUST NOT be present in the MID.
Tag Present (TAG)
Whether the tag field is present (1) or not (0) for
this MID. If this flag has a value of 1 then the tag
field MUST be present in the MID. Otherwise, the tag
field MUST NOT be present.
OID Type (OID)
Whether the contained OID field represents an full
OID (0), a parameterized OID (1), a compressed full
OID (2), or a compressed, parameterized OID (3).
For example, a MID flag byte of 0x00 indicates an atomic data
value with no issuer or tag field encapsulating a full OID.
A MID flag byte of 0x94 indicates a computed data value with
an issuer field, but no tag field encapsulating a compressed
OID.
Issuer
This is a binary identifier representing a predetermined
issuer name. The DTNMP protocol does not parse or validate
this identifier, using it only as a distinguishing bit
pattern to assure MID uniqueness. This value, for example,
may come from a global registry of organizations, an issuing
node address, or some other network-unique marking.
OID
The core of a MID is its encapsulated Object Identifier
(OID). Aside from the flag byte, this is the only other
mandatory element within a MID. The DTNMP defines four types
of OID references for this part of the MID structure: Full
OIDs, Parameterized OIDs, Compressed Full OIDs, and
Compressed Parameterized OIDs.
Full OID
This is a binary representation of the full OID
associated with the named value. The OID is encoded
using a modified form of the ASN.1 Basic Encoding
Rules (BER) for Object Identifiers (type value of
0x06). In the standard ASN.1 encoding, four octet
sets are defined: identifier octets, length octets,
contents octets, and end-of-contents octets. A DTNMP
Full OID does not use the identifier, length, or end-
Birrane & Ramachandran Expires July 4, 2015 [Page 19]
Internet-Draft DTNMP December 2014
of-contents octets. Instead, a DTNMP Full OID is
comprised of two fields: the length in bytes of the
encoded OID captured in an SDNV followed by the OID
contents octets, as illustrated in Figure 8.
Full OID Format
+------------+--------------------+
| OID Length | OID Content Octets |
| [SDNV] | [ASN.1 BER] |
+------------+--------------------+
Figure 8
Parameterized OID
The parameterized OID is represented as the non-
parameterized portions of the OID followed by one or
more parameters. Parameterized OIDs are used to
templatize the specification of data items and
otherwise provide parameters to controls without
requiring potentially unmanagable growth of a Full
OID namespace. The format of a parameterized OID is
given in Figure 9.
Parameterized OID Format
+----------+---------+--------+ +--------+
| Base OID | # Parms | Parm 1 | ... | Parm N |
| [VAR] | [SDNV] | [DC] | | [DC] |
+----------+---------+--------+ +--------+
Figure 9
Compressed Full OID
Since many related OIDs share a common and lengthy
hierarchy there is opportunity for significant
message size savings by defining a shorthand for
commonly-used portions of the OID tree. A partial
OID is a tuple consisting of a nickname for a pre-
defined portion of the OID tree (as an SDNV),
followed by a relative OID.
Compressed Parameterized OID
A compressed, parameterized OID is similar to a
compressed OID. In this instance, the tuple
contained in this field is the nickname for the pre-
defined portion of the OID tree (as an SDNV) followed
Birrane & Ramachandran Expires July 4, 2015 [Page 20]
Internet-Draft DTNMP December 2014
by a parameterized OID whose hierarchy begins at the
place identified by the nickname.
Tag
A value used to disambiguate multiple MIDs with the same OID/
Issuer combination. The definition of the tag is left to the
discretion of the MID issuer. Proper name objects do not
require a tag as their OIDs are guaranteed to be globally
unique. Options for tag values include an issuer-known
version number or a hashing of the data associated with a
non-proper-name MIDs. The tag field MUST NOT be present for
the atomic category.
4.4. Special Types
In addition to the primitive data types already mentioned, the
following special data types are also defined.
4.4.1. MID Collections (MC)
A MID collection is comprised of a value identifiying the number of
MIDs in the collection, followed by each MID, as illustrated in
Figure 10.
MID Collection
+--------+-------+ +-------+
| # MIDs | MID 1 | ... | MID N |
| [SDNV] | [MID] | | [MID] |
+--------+-------+ +-------+
Figure 10
4.4.2. Expressions (EXPR)
Expressions apply operations to data and literal values to generate
new data values. The expression type in DTNMP is a collection of
MIDs that represent a postfix notation stack of Data, Literal, and
Operation types. For example, the infix expression A * (B * C) is
represented as the sequence A B C * *. The format of an expression is
illustrated in Figure 11.
Birrane & Ramachandran Expires July 4, 2015 [Page 21]
Internet-Draft DTNMP December 2014
Expression Format
+----------+------------+
| Priority | Expression |
| [SDNV] | [MC] |
+----------+------------+
Figure 11
Priority
The priority of this expression relative to any other
expression configured on the DTNMP actor. Priorities are
used when one expression MUST be evaluated before some other
expression is evaluated. This field represents an unsigned
integer value with larger values indicating higher priority.
Unless otherwise specified, a default priority value of 0
SHALL be used for any defined expression.
Expression
An expression is represented in the DTNMP as a MID
collection, where each MID in the ordered collection
represents the data, literals, and operations that comprise
the expression.
4.4.3. Predicate (PRED)
Predicates are expressions whose values are interpretted as a
Boolean. The value of zero MUST be considered "false" and all other
values MUST be considered "true". Similar to an expression, a
predicate is represented as a MID collection.
5. Functional Specification
This section describes the format of the messages that comprise the
DTNMP protocol. When discussing the format/types of data that
comprise message fields, the following conventions are used.
Birrane & Ramachandran Expires July 4, 2015 [Page 22]
Internet-Draft DTNMP December 2014
+-----------+---------------------------------+
| Type Name | Description |
+-----------+---------------------------------+
| BYTE | Unsigned, 8-bit byte. |
| | |
| DC | Data Collection |
| | |
| EXPR | Expression |
| | |
| MC | MID Collection |
| | |
| MID | Managed Identifier |
| | |
| PRED | Predicate |
| | |
| SDNV | Self-Delimiting Numerical Value |
| | |
| TS | Timestamp |
| | |
| VAR | Variable field. |
+-----------+---------------------------------+
5.1. Message Group Format
Individual messages within the DTNMP are combined into a single group
for communication with another DTNMP actor. Messages within a group
MUST be received and applied as an atomic unit. The format of a
message group is illustrated in Figure 12. These message groups are
assumed communicated amongst agents and managers as the payloads of
encapsulating protocols, such as the Bundle Protocol or Internet
Protocol, which MAY provide additional security and data integrity
features.
DTNMP Message Group Format
+--------+-----------+-----------+ +-----------+
| # Msgs | Timestamp | Message 1 | ... | Message N |
| [SDNV] | [TS] | [VAR] | | [VAR] |
+--------+-----------+-----------+ +-----------+
Figure 12
# Msgs
The number of messages that are together in this message
group.
Timestamp
Birrane & Ramachandran Expires July 4, 2015 [Page 23]
Internet-Draft DTNMP December 2014
The creation time for this messaging group. This timestamp
MUST be an absolute time. Individual messages may have their
own creation timestamps based on their type, but the group
timestamp also serves as the default creation timestamp for
every message in the group.
Message N
The Nth message in the group.
5.2. Message Format
Each message identified in the DTNMP specification adheres to a
common message format, illustrated in Figure 13, consisting of a
message header, a message body, and an optional trailer.
DTNMP Message Format
+--------+-------+---------+
| Header | Body | Trailer |
| [BYTE] | [VAR] | [VAR] |
| | | (opt.) |
+--------+-------+---------+
Figure 13
Header
The message header byte is shown in Figure 14. The header
identifies a message context and opcode as well as flags that
control whether a report should be generated on message
success (Ack) and whether a report should be generated on
message failure (Nack).
DTNMP Common Message Header
+--------+----+---+---------+-------+
|ACL Used|Nack|Ack| Context |Opcode |
+--------+----+---+---------+-------+
| 7 | 6 | 5 | 4 3 | 2 1 0 |
+--------+----+---+---------+-------+
MSB LSB
Figure 14
Opcode
The opcode field identifies the opcode of the
message, within the associated message context.
ACK Flag
Birrane & Ramachandran Expires July 4, 2015 [Page 24]
Internet-Draft DTNMP December 2014
The ACK flag describes whether successfull
application of the message must generate an
ackowledgement back to the message sender. If this
flag is set (1) then the receiving actor MUST
generate a report communicating this status.
Otherwise, the actor MAY generate such a report based
on other criteria.
NACK Flag
The NACK flag describes whether a failure applying
the message must generate an error notice back to the
message sender. If this flag is set (1) then the
receiving actor MUST generate a report communicating
this status. Otherwise, the actor MAY generate such
a report based on other criteria.
ACL Used Flag
The ACL used flag indicates whether the message has a
trailer associated with it that specifies the list of
DTNMP actors that may participate in the actions or
definitions associated with the message. This area
is still under development.
Body
The message body contains the information associated with the
given message.
Trailer
An OPTIONAL access control list (ACL) may be appended as a
trailer to a message. When present, the ACL for a message
identifiers the agents and managers that can be affected by
the definitions and actions contained within the message.
The explicit impact of an ACL is described in the context of
each message below. When an ACL trailer is not present, the
message results may be visible to any DTNMP actor in the
network, pursuant to other security protocol implementations.
5.3. Register Agent (0x00)
The Register Agent message is used to inform a DTNMP manager of the
presence of another agent in the network.
+----------+
| Agent ID |
| [SDNV] |
+----------+
Figure 15: Register Agent Message Body
Birrane & Ramachandran Expires July 4, 2015 [Page 25]
Internet-Draft DTNMP December 2014
Agent ID
The Agent ID MUST represent the unique address of the agent
in whatever protocol is used to communicate with the agent.
For example, when DTNMP is run over Bundle Protocol, the
Agent ID should be the Endpoint Identifier (EID) of the agent
being added.
5.4. Data Report (0x12)
Data reports include a listing of one or more data items collected
from a managed device. These reports may include atomic data,
computed data, or any report definition known to the generating
device. Each message is a concatenation of ID/Data definitions with
the overall message length assumed to be captured in the underlying
transport container.
+------+------+-------+--------+ +-------+--------+
| Time | Num | ID 1 | Data 1 | | ID N | Data N |
| [TS] |[SDNV]| [MID] | [DC] |...| [MID] | [DC] |
+------+------+-------+--------+ +-------+--------+
Figure 16
Time
The time at which the report was generated by the DTNMP
actor.
Num
The number of reports in the data report message.
ID N
The MID identifying the Nth report.
Data N
The contents of the Nth report.
5.5. Perform Control (0x20)
The perform control method causes the receiving DTNMP actor to apply
one or more pre-configured controls.
Birrane & Ramachandran Expires July 4, 2015 [Page 26]
Internet-Draft DTNMP December 2014
Predicate Production Message
+-------+-----------+
| Start | Controls |
| [TS] | [MC] |
+-------+-----------+
Figure 17
Start
The time at which the control should be run.
Controls
The collection of controls to be applied by the DTNMP actor.
The MID identifying a control will contain the parameters for
the control (if any) through the use of a parameterized OID
captured within the MID.
6. Appliation Data Model Template
6.1. Overview
An application data model (ADM) specifies the set of DTNMP components
associated with a particular application/protocol. The purpose of
the ADM is to provide a guaranteed interface for the management of an
application or protocol over DTNMP that is independent of the nuances
of its software implementation. In this respect, the ADM is
conceptually similar to the Managed Information Base (MIB) used by
SNMP, but contains additional information relating to command opcodes
and more expressive syntax for automated behavior.
Currently, the ADM is an organizing document and not used to
automatically generate software. As such, the ADM template lists the
kind of information that must be present in an ADM definition but
does not address mechanisms for automating implementations.
Each ADM specifies the globally unique identifiers and descriptions
for all data, controls, literals, and operators associated with the
application or protocol maanged by the ADM. Any implementation
claiming compliance with a given ADM must compute all identified
data, perform identified controls, and understand identified literals
and operators.
6.2. ADM Types
ADMs must specify data types when defining data items and parameters.
In addition to the standard DTNMP Types (SDNV, TS, DC, MID, OID,
Birrane & Ramachandran Expires July 4, 2015 [Page 27]
Internet-Draft DTNMP December 2014
P_OID, MC, EXPR, and PRED) ADMs support the following additional data
types.
+------------+--------+-----------------------------+---------------+
| Data Type | ID | Description | Encapsulating |
| | | | DTNMP Type |
+------------+--------+-----------------------------+---------------+
| Integer | INT | A signed or unsigned | SDNV |
| | | integer up to 64 bits in | |
| | | width encoded using Google | |
| | | Protocol Buffer VARINT | |
| | | rules. Booleans, | |
| | | enumerations, and all | |
| | | integer values are captured | |
| | | using this data type. | |
| | | | |
| Float | FLOAT | A 32-bit fixed-width number | SDNV |
| | | stored according to the | |
| | | IEEE-754 float standard. | |
| | | | |
| Double | DOUBLE | A 64-bit fixed-width number | SDNV |
| | | stored according to the | |
| | | IEEE-754 double standard. | |
| | | | |
| STRING | STR | An array of characters | DC |
| | | preceeded by the character | |
| | | count. Strings are not | |
| | | required to be NULL- | |
| | | terminated. | |
| | | | |
| Binary | BLOB | An undefined series of | DC |
| Large | | user-defined bytes | |
| Object | | preceeded by the length of | |
| | | the binary object. This | |
| | | data type is captured . | |
+------------+--------+-----------------------------+---------------+
Table 3: ADM Data Types
6.3. Template
ADM definitions specify the metadata, data, controls, literals, and
operators associated with a managed application or protocol.
Birrane & Ramachandran Expires July 4, 2015 [Page 28]
Internet-Draft DTNMP December 2014
6.3.1. ADM Metadata
ADM metadata consist of the items necessary to uniquely identify the
ADM itself. The required metadata items include the following.
+-------------+--------+-------------------------------------+------+
| Item | Type | Description | Req. |
+-------------+--------+-------------------------------------+------+
| Name | STR | The human-readible name of the ADM. | Y |
| | | | |
| Version | STR | Version of the ADM encoded as a | Y |
| | | string. | |
| | | | |
| OID | OID | ADMs provide an ordered list of | N |
| Nickname N | | nicknames that can be used by other | |
| | | MIDs in the ADM definition to | |
| | | defined compressed OIDs. There can | |
| | | an arbitratry number of nicknames | |
| | | defined for an ADM. | |
+-------------+--------+-------------------------------------+------+
Table 4: ADM Terminology
6.3.2. ADM Information Capture
The ADM Data Section consist of all components in the "data" category
associated with the managed application or protocol. The information
that must be provided for each of these items is as follows.
Name
Every component in an ADM MUST be given a human-readable,
consistent name that unqiuely identifies the component in the
context of the application or protocol. These names will be used
by human-computer interfaces for manipulating components.
MID
The managed identifier that describes this data item. MIDs in
components identified by an ADM MUST NOT contain an issuer or a
tag value. In cases where a partial OID is specified, the ADM OID
prefix is presumed as the base. In cases where the OID is
parameterized, the parameter values are not included in the MID
definition in the ADM as parameters are provided at runtime by
implementations.
OID
A human-readible version of the OID encapsulated in the MID for
the component (e.g., 1.2.3.4). When a nickname is used to
represent an compressed OID, the nickname enumeration is included
Birrane & Ramachandran Expires July 4, 2015 [Page 29]
Internet-Draft DTNMP December 2014
in this field enclosed by square brackets. For example, if OID
nickname 0 refers to the OID prefix 1.2.3.4.5, then the OID
1.2.3.4.5.6 may be listed more compactly as [0].6
Description
Every component in an ADM MUST be given a human-readable,
consistent description that provides a potential user with a
compact, effective summary of the component.
Type
For components that evaluate to a data value, the data type for
that value must be represented.
# Parameters
For components with a parameterized OID, the ADM MUST provide the
expected number of parameters. A value of 0 indicates that the
OID has no parameters and MUST NOT be used for any MID which has a
parameterized OID. When ommitted, the number of parameters is
considered 0.
Parameter N Name
Each parameter of a parameterized component must be given a name.
Parameter N Description
Each parameter of a parameterized component must be given a
summary that describes how the parameter will be used by the
application or protocol.
Parameter N Type
Each parameter of a parameterized component must be given a type
that describes the structre capturing the parameter value.
Notably, while parameters in the OID form something similar to a
function prototype, there is no sense of function call or stack
and therefore all parameters should be considered as pass-by-
value.
7. DTNMP Agent Application Data Model
7.1. Data Definitions
This section provides the ADM for a DTNMP Agent. This ADM may
eventually be removed from the DTNMP specification into its own
standards document. All DTNMP agents MUST support the items
described in this section.
Birrane & Ramachandran Expires July 4, 2015 [Page 30]
Internet-Draft DTNMP December 2014
7.2. Metadata Definitions
+-------------+-------+------------+--------------------------------+
| Item | Type | Value | Comment |
+-------------+-------+------------+--------------------------------+
| Name | STR | DTNMP | |
| | | Agent ADM | |
| | | | |
| Version | STR | 2014-12-31 | |
| | | | |
| OID | OID | 1.1 | 1.1 is currently used only as |
| Nickname 0 | | | a non-operational example of |
| | | | an ADM base. |
+-------------+-------+------------+--------------------------------+
Table 5: DTNMP Agent Metadata
7.3. Data Definitions
The DTNMP Agent ADM defines the following atomic data definitions
that represent the set of data that MUST be collected by any DTNMP
agent implementation.
7.3.1. Atomic Data
Birrane & Ramachandran Expires July 4, 2015 [Page 31]
Internet-Draft DTNMP December 2014
+------------------+----------+---------+----------------+----------+
| Name | MID | OID | Description | Type |
+------------------+----------+---------+----------------+----------+
| DefinedReports | 0x800200 | [0].0.0 | # Reports | INT |
| | | | Defined | |
| | | | | |
| SentReports | 0x800201 | [0].0.1 | # Reports Sent | INT |
| | | | | |
| DefinedTimeRules | 0x800202 | [0].0.2 | # Active Time- | INT |
| | | | Based | |
| | | | Production | |
| | | | Rules | |
| | | | | |
| RunTimeRules | 0x800203 | [0].0.3 | # Run Time- | INT |
| | | | Based | |
| | | | Production | |
| | | | Rules | |
| | | | | |
| DefinedConsts | 0x800204 | [0].0.4 | # Constants | INT |
| | | | Defined | |
| | | | | |
| DefinedCustom | 0x800205 | [0].0.5 | # Computed | INT |
| | | | Data | |
| | | | Definitions | |
| | | | | |
| DefinedMacros | 0x800206 | [0].0.6 | # Macros | INT |
| | | | Defined | |
| | | | | |
| RunMacros | 0x800207 | [0].0.7 | # Macros Run | INT |
| | | | | |
| DefinedCtrls | 0x800208 | [0].0.8 | # Controls | INT |
| | | | Defined | |
| | | | | |
| RunCtrls | 0x800209 | [0].0.9 | # Controls | INT |
| | | | Defined | |
+------------------+----------+---------+----------------+----------+
Table 6: DTNMP Agent Atomic Data
7.3.2. Computed Data
The DTNMP Agent ADM does not define any computed data items.
7.3.3. Reports
Birrane & Ramachandran Expires July 4, 2015 [Page 32]
Internet-Draft DTNMP December 2014
+------------+----------+---------+------------------+--------------+
| Name | MID | OID | Description | Type |
+------------+----------+---------+------------------+--------------+
| FullReport | 0x880220 | [0].2.0 | Report of all | DC |
| | | | atomic data | |
| | | | items | |
+------------+----------+---------+------------------+--------------+
Table 7: DTNMP Agent Reports
7.4. Operators
This section describes the standard set of operators available to all
DTNMP agents. Applications and protocols do not need to redefine
these operators, as they may be used in any expressions evaluated by
any agent.
Birrane & Ramachandran Expires July 4, 2015 [Page 33]
Internet-Draft DTNMP December 2014
+------------+-----------+----------+-------------------------------+
| Name | MID | OID | Description |
+------------+-----------+----------+-------------------------------+
| + | 0x830260 | [0].6.0 | Addition |
| | | | |
| - | 0x830261 | [0].6.1 | Subtraction |
| | | | |
| * | 0x830262 | [0].6.2 | Multiplication |
| | | | |
| / | 0x830263 | [0].6.3 | Division |
| | | | |
| % | 0x830264 | [0].6.4 | Modulo |
| | | | |
| ^ | 0x830265 | [0].6.5 | Exponentiation |
| | | | |
| & | 0x830266 | [0].6.6 | Bitwise AND |
| | | | |
| | | 0x830267 | [0].6.7 | Bitwise OR |
| | | | |
| # | 0x830268 | [0].6.8 | Bitwise XOR |
| | | | |
| ~ | 0x830269 | [0].6.9 | Bitwise NOT |
| | | | |
| && | 0x83026A | [0].6.A | Logical AND |
| | | | |
| || | 0x83026B | [0].6.B | Logical OR |
| | | | |
| ## | 0x83026C | [0].6.C | Logical XOR |
| | | | |
| ! | 0x83026D | [0].6.D | Logical NOT |
| | | | |
| abs | 0x83026E | [0].6.E | Absolute Value |
| | | | |
| < | 0x83026F | [0].6.F | Less than |
| | | | |
| > | 0x8303610 | [0].6.10 | Greater than |
| | | | |
| <= | 0x8303611 | [0].6.11 | Less than or equal to |
| | | | |
| >= | 0x8303612 | [0].6.12 | Greater than or equal to |
| | | | |
| != | 0x8303613 | [0].6.13 | Not equal |
| | | | |
| == | 0x8303614 | [0].6.14 | Equal to |
+------------+-----------+----------+-------------------------------+
Table 8: DTNMP Agent Atomic Data
Birrane & Ramachandran Expires July 4, 2015 [Page 34]
Internet-Draft DTNMP December 2014
7.5. Controls
This section describes the controls available for use on any DTNMP
agent. Since this section essentially provides a functional
specification for the DTNMP agent, it is presented in two sections.
First, a summary section provides a quick reference for the controls
available on a DTNMP agent. Second, a full control specification
provides detailed information on each individual DTNMP agent control.
7.5.1. Control Summary
+----------------+-----------+----------+---------------------------+
| Name | MID | OID | Description |
+----------------+-----------+----------+---------------------------+
| ListADMs | 0x810230 | [0].3.0 | List all ADMs known to |
| | | | the agent. |
| | | | |
| ListAtomicIDs | 0x810231 | [0].3.1 | List all Atomic MIDs |
| | | | known to the agent. |
| | | | |
| DescAtomicData | 0xC10232 | [0].3.2 | Dump information for |
| | | | given Atomic MIDs. |
| | | | |
| AddCompData | 0xC10233 | [0].3.3 | Define a computed data |
| | | | definition on the agent. |
| | | | |
| DelCompData | 0xC10234 | [0].3.4 | Remove a computed data |
| | | | definition from the |
| | | | agent. |
| | | | |
| ListCompData | 0x810235 | [0].3.5 | List known computed data |
| | | | MIDs. |
| | | | |
| DescCompData | 0xC10236 | [0].3.6 | Dump information for |
| | | | given computed data MIDs. |
| | | | |
| AddRptDef | 0xC10237 | [0].3.7 | Define a custom report. |
| | | | |
| DelRptDef | 0xC10238 | [0].3.8 | Forget a custom report. |
| | | | |
| ListRpts | 0x810239 | [0].3.9 | List known custom report |
| | | | MIDs. |
| | | | |
| DescRpts | 0xC1023A | [0].3.A | Dump information for |
| | | | given custom report MIDs. |
| | | | |
| ListOps | 0x81023B | [0].3.B | List known operator IDs. |
| | | | |
Birrane & Ramachandran Expires July 4, 2015 [Page 35]
Internet-Draft DTNMP December 2014
| DescOps | 0xC1023C | [0].3.C | Dump information for |
| | | | given operator MIDs. |
| | | | |
| ListCtrls | 0x81023D | [0].3.D | List known custom control |
| | | | MIDs. |
| | | | |
| DescCtrls | 0xC1023E | [0].3.E | Dump information for |
| | | | given controls MIDs. |
| | | | |
| AddMacroDef | 0xC1023F | [0].3.F | Define a custom macro. |
| | | | |
| DelMacroDef | 0xC103310 | [0].3.10 | Forget a custom macro. |
| | | | |
| ListMacros | 0x8103311 | [0].3.11 | List known custom macro |
| | | | MIDs. |
| | | | |
| DescMacros | 0xC103312 | [0].3.12 | Dump information for |
| | | | given custom macro MIDs. |
| | | | |
| AddTimeRule | 0xC103313 | [0].3.13 | Define a time-based prod |
| | | | rule. |
| | | | |
| DelTimeRule | 0xC103314 | [0].3.14 | Forget a time-based prod |
| | | | rule. |
| | | | |
| ListTimeRules | 0x8103315 | [0].3.15 | List known time-based |
| | | | rules. |
| | | | |
| DescTimeRules | 0xC103316 | [0].3.16 | Dump information for |
| | | | given time-based rules. |
| | | | |
| AddStateRule | 0xC103317 | [0].3.17 | Define a state-based prod |
| | | | rule. |
| | | | |
| DelStateRule | 0xC103318 | [0].3.18 | Forget a state-based prod |
| | | | rule. |
| | | | |
| ListStateRules | 0x8103319 | [0].3.19 | List known state-based |
| | | | rules. |
| | | | |
| DescStateRules | 0xC10331A | [0].3.1A | Dump information for |
| | | | given state-based rules. |
+----------------+-----------+----------+---------------------------+
Table 9: DTNMP Agent Controls Summary
Birrane & Ramachandran Expires July 4, 2015 [Page 36]
Internet-Draft DTNMP December 2014
7.5.2. Control Specification
7.5.2.1. ListADMs
This control causes the agent to produce a report detailing the list
of all ADMs configured on the agent and available for use.
This control takes no parameters.
This control causes a report to be generated with the following
format.
ListADMs Report Format
+--------+------------+ +------------+
| # ADMs | ADM 1 Name | ... | ADM N Name |
| [SDNV] | [STR] | | [STR] |
+--------+------------+ +------------+
Figure 18
# ADMs
The number of ADMs known to the agent.
ADM [x] Name
For each ADM, it's human readable name.
7.5.2.2. ListAtomicIDs
This control causes the agent to produce a list containing the MID of
every atomic data item understood by the agent.
This control takes no parameters.
This control causes a report to be generated with the following
format.
ListAtomicIDs Report Format
+------------+
| Atomic IDs |
| [MC] |
+------------+
Figure 19
Atomic IDs
Birrane & Ramachandran Expires July 4, 2015 [Page 37]
Internet-Draft DTNMP December 2014
A MID Collection of the MIDs of each atomic data definition
known to the agent.
7.5.2.3. DescAtomicData
This control causes the agent to produce a detailed description of
the requested atomic data definitions.
This control takes 1 parameter in the following format.
DescAtomicData Parameters
+------------+
| Atomic IDs |
| [MC] |
+------------+
Figure 20
Atomic IDs
The list of MIDs identifying the atomic IDs to be described.
This control causes a report to be generated with the following
format.
DescAtomicData Report Format
+--------+----------+----------+ +----------+----------+
| # IDs | ID1 Name | ID1 Type |... | IDn Name | IDn Type |
| [SDNV] | [STR] | [SDNV] | | [STR] | [SDNV] |
+--------+----------+----------+ +----------+----------+
Figure 21
# IDs
The number of atomic data descriptions returned.
ID[n] Name
The name of the nth returned atomic data item.
ID[n] Type
Type enumeration for the nth atomic data item.
7.5.2.4. AddCompData
This control configures a new computed data definition on the agent.
A computed data item uses an expression to assign a data value.
Birrane & Ramachandran Expires July 4, 2015 [Page 38]
Internet-Draft DTNMP December 2014
This control takes 3 parameters in the following format.
AddCompData Parameters
+--------+--------+--------+
| Def ID | Def | Type |
| [MID] | [EXPR] | [SDNV] |
+--------+--------+--------+
Figure 22
Def ID
The MID value identifying the new computed data definition.
Def
The expression used to calculate the value for the new
computed data item.
Type
The data type for the resultant computed data value.
This control causes no report to be produced.
7.5.2.5. DelCompData
This control removes a computed data definition from the agent.
This control takes 1 parameter in the following format.
DelCompData Parameters
+---------------+
| IDs To Remove |
| [MC] |
+---------------+
Figure 23
IDs To Remove
The list of computed data items to be removed from the agent.
This control causes no report to be produced.
7.5.2.6. ListCompData
This control causes the agent to produce a list containing the MID of
every computed data definition understood by the agent.
Birrane & Ramachandran Expires July 4, 2015 [Page 39]
Internet-Draft DTNMP December 2014
This control takes no parameters.
This control causes a report to be generated with the following
format.
ListCompData Report Format
+------------+
| Custom IDs |
| [MC] |
+------------+
Figure 24
Custom IDs
The collection of identifiers for those computed data
definitions known to the agent.
7.5.2.7. DescCompData
This control causes the agent to produce a detailed description of
the requested computed data definitions.
This control takes 1 parameter in the following format.
DescCompData Parameters
+----------+
| Comp IDs |
| [MC] |
+----------+
Figure 25
Comp IDs
The MID collection identifying the computed data items to be
described.
This control causes a report to be generated with the following
format.
Birrane & Ramachandran Expires July 4, 2015 [Page 40]
Internet-Draft DTNMP December 2014
DescCompData Report Format
+------+-------+--------+---------+ +-------+--------+--------+
|# IDs | C1 ID | C1 Def | C1 Type |... | Cn ID | Cn Def | Cn Type|
|[SDNV]| [MID] | [EXPR] | [SDNV] | | [MID] | [EXPR] | [SDNV] |
+------+-------+--------+---------+ +-------+--------+--------+
Figure 26
# IDs
The number of computed data definitions in the report.
C[n] ID
The MID of the nth computed data definition.
C[n] Def
The expression used to calculate the value of the Nth
computed data item.
C[n] Type
The data type of the value of the Nth computed data item.
7.5.2.8. AddRptDef
This control configures a new custom report definition on the agent.
A custom report assigns a single MID value to represent an ordered
collection of other MID values, with some administrative information
that identifies what other nodes in the network may request and
process this report.
This control takes 2 parameters in the following format.
AddRptDef Parameters
+--------+------------+
| RPT ID | Definition |
| [MID] | [MC] |
+--------+------------+
Figure 27
Rpt ID
The MID for the new report.
Definition
The ordered set of MIDs representing the contents of the
report.
Birrane & Ramachandran Expires July 4, 2015 [Page 41]
Internet-Draft DTNMP December 2014
This control causes no report to be produced.
7.5.2.9. DelRptDef
This control removes a custom report definition from the agent.
This control takes 1 parameters in the following format.
DelRptDef Parameters
+---------------+
| IDs To Remove |
| [MC] |
+---------------+
Figure 28
IDs to Remove
The collection of MIDs identifying the report definitions to
remove from the agent.
This control causes no report to be produced.
7.5.2.10. ListRpts
This control causes the agent to produce a list containing the MID of
every report definition understood by the agent.
This control takes no parameters.
This control causes a report to be generated with the following
format.
ListRpts Report Format
+---------+
| Reports |
| [MC] |
+---------+
Figure 29
Reports
The collection of MIDs representing custom report IDs known
to the agent.
Birrane & Ramachandran Expires July 4, 2015 [Page 42]
Internet-Draft DTNMP December 2014
7.5.2.11. DescRpts
This control causes the agent to produce a detailed description of
the requested report definitions.
This control takes 1 parameter in the following format.
DescRpts Parameters
+------------+
| Report IDs |
| [MC] |
+------------+
Figure 30
Report IDs
The collection of MIDs identifying the report definitions to
be described.
This control causes a report to be generated with the following
format.
DescRpts Report Format
+--------+----------+-----------+ +----------+-----------+
| # IDs | RPT 1 ID | RPT 1 Def | ... | RPT N ID | RPT N Def |
| [SDNV] | [MID] | [MC] | | [MID] | [MC] |
+--------+----------+-----------+ +----------+-----------+
Figure 31
# IDs
The number of report definitions in this report.
RPT[n] ID
The MID of the nth report definition.
RPT[n] Def
The ordered collection of IDs comprising the Nth report
definition.
7.5.2.12. ListOps
This control causes the agent to produce a list containing the MID of
every operator understood by the agent.
This control takes no parameters.
Birrane & Ramachandran Expires July 4, 2015 [Page 43]
Internet-Draft DTNMP December 2014
This control causes a report to be generated with the following
format.
ListOps Report Format
+------+
| OPS |
| [MC] |
+------+
Figure 32
OPS
The collection of MIDs for every op known by the agent.
7.5.2.13. DescOps
This control causes the agent to produce a detailed listing of the
requested operator definitions.
This control takes 1 parameter in the following format.
DescOps Parameters
+--------+
| OP IDs |
| [MC] |
+--------+
Figure 33
OP IDs
The set of operators to be described.
This control causes a report to be generated with the following
format.
DescOps Report Format
+--------+---------+-----------+ +---------+-----------+
| # OPs | OP 1 ID | OP 1 Desc | ... | OP N ID | OP N Desc |
| [SDNV] | [MID] | [STR] | | [MID] | [STR] |
+--------+---------+-----------+ +---------+-----------+
Figure 34
# OPs
The number of operator definitions in the report.
Birrane & Ramachandran Expires July 4, 2015 [Page 44]
Internet-Draft DTNMP December 2014
OP[n] ID
The MID of the nth operator definition.
OP[n] Def
The description of the nth operator.
7.5.2.14. ListCtrls
This control causes the agent to produce a list containing the MID of
every control understood by the agent.
This control takes no parameters.
This control causes a report to be generated with the following
format.
ListCtrls Report Format
+-------+
| CTRLs |
| [MC] |
+-------+
Figure 35
CTRLs
The collection of MIDs of controls known to the agent.
7.5.2.15. DescCtrls
This control causes the agent to produce a detailed listing of the
requested control definitions.
This control takes 1 parameter in the following format.
DescCtrls Parameters
+----------+
| CTRL IDs |
| [MC] |
+----------+
Figure 36
CTRL IDs
The set of controls to be described.
Birrane & Ramachandran Expires July 4, 2015 [Page 45]
Internet-Draft DTNMP December 2014
This control causes a report to be generated with the following
format.
DescCtrls Report Format
+---------+----------+------------+ +----------+------------+
| # CTRLs | CTRL1 ID | CTRL1 Desc | ... | CTRLN ID | CTRLN Desc |
| [SDNV] | [MID] | [STR] | | [MID] | [STR] |
+---------+----------+------------+ +----------+------------+
Figure 37
# CTRLs
The number of control definitions in the report.
CTRL[n] ID
The MID of the nth control definition.
CTRL[n] Desc
The description of the Nth control definition, to include
information on parameters.
7.5.2.16. AddMacroDef
This control configures a new custom macro definition on the agent.
A macro is a series of controls that should be run in sequence.
This control takes 3 parameters in the following format.
AddMacroDef Parameters
+------------+----------+------+
| Macro Name | Macro ID | Def |
| [STR] | [MID] | [MC] |
+------------+----------+------+
Figure 38
Macro Name
The descriptive name for the macro.
Macro ID
The MID value identifying the new macro.
Def
The ordered set of controls/macros that are run sequentially
during macro execution.
Birrane & Ramachandran Expires July 4, 2015 [Page 46]
Internet-Draft DTNMP December 2014
This control causes no report to be produced.
7.5.2.17. DelMacroDef
This control removes a custom macro definition from the agent.
This control takes 1 parameters in the following format.
DelMacroDef Parameters
+---------------+
| IDs To Remove |
| [MC] |
+---------------+
Figure 39
IDs To Remove
The collection of MIDs identifying the macros to be removed
from the agent.
This control causes no report to be produced.
7.5.2.18. ListMacros
This control causes the agent to produce a list containing the MID of
every custom macro definition understood by the agent.
This control takes no parameters.
This control causes a report to be generated with the following
format.
ListMacros Report Format
+-----------+
| Macro IDs |
| [MC] |
+-----------+
Figure 40
Macro IDs
The list of macro definitions known to the agent.
Birrane & Ramachandran Expires July 4, 2015 [Page 47]
Internet-Draft DTNMP December 2014
7.5.2.19. DescMacros
This control causes the agent to produce a detailed listing of the
requested macro definitions.
This control takes 1 parameter in the following format.
DescMacros Parameters
+-----------+
| Macro IDs |
| [MC] |
+-----------+
Figure 41
Macro IDs
The collection of MIDs identifying the macros to be
described.
This control causes a report to be generated with the following
format.
DescMacros Report Format
+--------+-------+-----+------+ +-------+-----+------+
|# Macros|M1 Name|M1 ID|M1 Def| ... |Mn Name|Mn ID|Mn Def|
| [SDNV] | [STR] |[MID]| [MC] | | [STR] |[MID]| [MC] |
+--------+-------+-----+------+ +-------+-----+------+
Figure 42
# Macros
The number of macro definitions in the report.
M[n] Name
The name of the nth macro definition.
M[n] ID
The MID of the nth macro definition. v
M[n] Def
The expression used to calculate the value of the Nth
computed data item.
Birrane & Ramachandran Expires July 4, 2015 [Page 48]
Internet-Draft DTNMP December 2014
7.5.2.20. AddTimeRule
This control configures a new time-based production rule on the
agent. A time-based production rule instructs the agent to produce a
report comprising a fixed set of component values periodically over
time. The component values may represent any type of data value,
including atomic data, computed data, or reports.
This control takes 4 parameters in the following format.
AddTimeRule Parameters
+--------+------------+--------+---------+
| Start | Period (s) | Count | Results |
| [TS] | [SDNV] | [SDNV] | [MC] |
+--------+------------+--------+---------+
Figure 43
Start
The time at which the production should commence.
Period
The number of seconds to wait between report message
generation.
Count
The number of reports to be generated by this configuration.
The special value of 0 indicates production should continue
indefinitely.
Results
The collection of MIDs to be included in the report.
No report is produced in response to this individual command. THe
configured reports will be produced in accordance to the configured
time period.
7.5.2.21. DelTimeRule
This control removes a time-based production rule from the agent.
This control takes 1 parameters in the following format.
Birrane & Ramachandran Expires July 4, 2015 [Page 49]
Internet-Draft DTNMP December 2014
DelTimeRule Parameters
+----------+
| Rule IDs |
| [MC] |
+----------+
Figure 44
Rule IDs
The collection of MIDs identifying the rules to be removed
from the agent.
This control causes no report to be produced.
7.5.2.22. ListTimeRules
This control causes the agent to produce a list containing the MID of
every time-based production rule understood by the agent.
This control takes no parameters.
This control causes a report to be generated with the following
format.
ListTimeRules Report Format
+----------+
| Rule IDs |
| [MC] |
+----------+
Figure 45
Rule IDs
The collection of MIDs identifying the time-based rules known
to the agent.
7.5.2.23. DescTimeRules
This control causes the agent to produce a detailed listing of the
requested time-based production rules.
This control takes 1 parameter in the following format.
Birrane & Ramachandran Expires July 4, 2015 [Page 50]
Internet-Draft DTNMP December 2014
DescTimeRules Parameters
+----------+
| Rule IDs |
| [MC] |
+----------+
Figure 46
Rule IDs
The collection of MIDs identifying the time-based rules to be
described.
This control causes a report to be generated with the following
format.
DescTimeRules Report Format
+--------+-------+----------+-----------+----------+-----------+
|# Rules | R1 ID | R1 START | R1 PERIOD | R1 Count | R1 Result | ...
| [SDNV] | [MID] | [TS] | [SDNV] | [SDNV] | [MC] |
+--------+-------+----------+-----------+----------+-----------+
Figure 47
# Rules
The number of time-based rule definitions in the report.
R[n] ID
The MID identifier for the nth time-based rule definition.
R[n] Start
The time at which the nth time-based rule production should
commence.
R[n] Period
The number of seconds to wait between running the nth time-
based rule.
R[n] Count
The number of reports to be generated by the nth time-based
report. The special value of 0 indicates production should
continue indefinitely.
R[n] Results
The collection of MIDs to be included in the report generated
by the nth time-based rule.
Birrane & Ramachandran Expires July 4, 2015 [Page 51]
Internet-Draft DTNMP December 2014
7.5.2.24. AddStateRule
This control configures a new state-based production rule on the
agent. A state-based production rule instructs the agent to produce
a report comprising a fixed set of component values periodically
whenever the expression evaluates to true. The component values may
represent any type of data value, including atomic data, computed
data, or reports.
This control takes 4 parameters in the following format.
AddStateRule Parameters
+--------+--------+--------+---------+
| Start | State | Count | Results |
| [TS] | [PRED] | [SDNV] | [MC] |
+--------+--------+--------+---------+
Figure 48
Start
The time at which the production should commence.
State
The expression which, when non-zero, causes the report to be
generated.
Count
The number of reports to be generated by this configuration.
The special value of 0 indicates production should continue
indefinitely.
Results
The collection of MIDs to be included in the report.
No report is produced in response to this individual command.
7.5.2.25. DelStateRule
This control removes a state-based production rule from the agent.
This control takes 1 parameters in the following format.
Birrane & Ramachandran Expires July 4, 2015 [Page 52]
Internet-Draft DTNMP December 2014
DelStateRule Parameters
+----------+
| Rule IDs |
| [MC] |
+----------+
Figure 49
Rule IDs
The collection of MIDs identifying the rules to be removed
from the agent.
This control causes no report to be produced.
7.5.2.26. ListStateRules
This control causes the agent to produce a list containing the MID of
every state-based production rule understood by the agent.
This control takes no parameters.
This control causes a report to be generated with the following
format.
ListStateRules Report Format
+----------+
| Rule IDs |
| [MC] |
+----------+
Figure 50
Rule IDs
The collection of MIDs identifying the state-based rules
known to the agent.
7.5.2.27. DescStateRules
This control causes the agent to produce a detailed listing of the
requested state-based production rules.
This control takes 1 parameter in the following format.
Birrane & Ramachandran Expires July 4, 2015 [Page 53]
Internet-Draft DTNMP December 2014
DescStateRules Parameters
+----------+
| Rule IDs |
| [MC] |
+----------+
Figure 51
Rule IDs
The collection of MIDs identifying the state-based rules to
be described.
This control causes a report to be generated with the following
format.
DescStateRules Report Format
+--------+-------+----------+-----------+----------+-----------+
|# Rules | R1 ID | R1 START | R1 PERIOD | R1 Count | R1 Result | ...
| [SDNV] | [MID] | [TS] | [SDNV] | [SDNV] | [MC] |
+--------+-------+----------+-----------+----------+-----------+
Figure 52
# Rules
The number of state-based rule definitions in the report.
R[n] ID
The MID identifier for the nth state-based rule definition.
R[n] Start
The time at which the nth state-based rule production should
commence.
R[n] Period
The number of seconds to wait between running the nth state-
based rule.
R[n] Count
The number of reports to be generated by the nth state-based
report. The special value of 0 indicates production should
continue indefinitely.
R[n] Results
The collection of MIDs to be included in the report generated
by the nth state-based rule.
Birrane & Ramachandran Expires July 4, 2015 [Page 54]
Internet-Draft DTNMP December 2014
8. IANA Considerations
At this time, this protocol has no fields registered by IANA.
9. Security Considerations
Transport security is handled by the transport layer, for example the
Bundle Security Protocol [RFC6257] when using the Bundle Protocol
[RFC5050].
Finer grain application security is done via ACLs which are defined
via configuration messages and implementation specific.
10. Normative References
[DTNM] Birrane, E. and H. Kruse, "DTN Network management: The
Definition and Exchange of Infrastructure Information in
High Delay Environments", .
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4838] Cerf, V., Burleigh, S., Hooke, A., Torgerson, L., Durst,
R., Scott, K., Fall, K., and H. Weiss, "Delay-Tolerant
Networking Architecture", RFC 4838, April 2007.
[RFC5050] Scott, K. and S. Burleigh, "Bundle Protocol
Specification", RFC 5050, November 2007.
[RFC6256] Eddy, W. and E. Davies, "Using Self-Delimiting Numeric
Values in Protocols", RFC 6256, May 2011.
[RFC6257] Symington, S., Farrell, S., Weiss, H., and P. Lovell,
"Bundle Security Protocol Specification", RFC 6257, May
2011.
[tolerance]
Birrane, E., Burleigh, S., and V. Cerf, "Defining
Tolerance: Impacts of Delay and Didruption when Managing
Challenged Networks", 2001.
Authors' Addresses
Edward J. Birrane
Johns Hopkins Applied Physics Laboratory
Email: Edward.Birrane@jhuapl.edu
Birrane & Ramachandran Expires July 4, 2015 [Page 55]
Internet-Draft DTNMP December 2014
Vignesh Ramachandran
Johns Hopkins Applied Physics Laboratory
Email: Vinny.Ramachandran@jhuapl.edu
Birrane & Ramachandran Expires July 4, 2015 [Page 56]