Internet DRAFT - draft-mcdonald-ldap-printer-schema
draft-mcdonald-ldap-printer-schema
Network Working Group Pat Fleming
INTERNET-DRAFT Independent
Obsoletes: 3712 (if approved) Ira McDonald
Intended Status: Informational High North
Expires: 30 October 2015 30 April 2015
Lightweight Directory Access Protocol (LDAP):
Schema for Printer Services
<draft-mcdonald-ldap-printer-schema-13.txt>
Abstract
This document defines a schema, object classes and attributes, for
Printers and Print Services, for use with directories that support
Lightweight Directory Access Protocol (RFC 4510). This document is
based on the Printer attributes listed in Appendix E of Internet
Printing Protocol/1.1 (RFC 2911). Additional Printer attributes are
based on definitions in the Printer MIB v2 (RFC 3805), IEEE-ISTO PWG
Command Set for IEEE 1284 Device ID (PWG 5107.2), IEEE-ISTO PWG IPP
Job and Printer Extensions - Set 3 (PWG 5100.13), and IEEE-ISTO PWG
IPP Everywhere (PWG 5100.14).
This memo is an independent submission to the RFC Editor Stream by
the Internet Printing Protocol Working Group of the IEEE-ISTO Printer
Working Group, as part of their PWG IPP Everywhere (PWG 5100.14)
project for secure mobile printing with vendor-neutral Client
software.
This document obsoletes RFC 3712.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 30 October 2015.
Copyright Notice
Fleming, McDonald Expires 30 October 2015 [Page 1]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Fleming, McDonald Expires 30 October 2015 [Page 2]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
Table of Contents
1. Introduction ............................................... 5
1.1. Relationship to SLP Printer Service .................... 5
1.2. Source of LDAP Printer Attributes ...................... 5
1.3. Source of LDAP Printer Schema OIDs ..................... 6
1.3.1. IBM Assignments for RFC 3712 ....................... 6
1.3.2. IEEE-ISTO PWG Assignments .......................... 6
1.4. Rationale for Design Choices ........................... 6
1.4.1. Rationale for using DirectoryString Syntax ......... 6
1.4.2. Rationale for using caseIgnoreMatch ................ 7
1.4.3. Rationale for using caseIgnoreSubstringsMatch ...... 8
2. Conventions Used in This Document .......................... 8
2.1. Requirements Language .................................. 8
2.2. LDAP Schema Descriptions ............................... 9
2.3. Abbreviations .......................................... 9
3. Definition of Object Classes ............................... 10
3.1. slpServicePrinter ...................................... 11
3.2. printerAbstract ........................................ 11
3.3. printerService ......................................... 12
3.4. printerServiceAuxClass ................................. 12
3.5. printerIPP ............................................. 13
3.6. printerLPR ............................................. 13
4. Definition of Attribute Types .............................. 14
4.1. printer-uri ............................................ 16
4.2. printer-xri-supported .................................. 17
4.3. printer-name ........................................... 18
4.4. printer-natural-language-configured .................... 19
4.5. printer-location ....................................... 20
4.6. printer-info ........................................... 20
4.7. printer-more-info ...................................... 21
4.8. printer-make-and-model ................................. 21
4.9. printer-ipp-versions-supported ......................... 22
4.10. printer-multiple-document-jobs-supported .............. 23
4.11. printer-charset-configured ............................ 23
4.12. printer-charset-supported ............................. 23
4.13. printer-generated-natural-language-supported .......... 24
4.14. printer-document-format-supported ..................... 25
4.15. printer-color-supported ............................... 25
4.16. printer-compression-supported ......................... 25
4.17. printer-pages-per-minute .............................. 26
4.18. printer-pages-per-minute-color ........................ 26
4.19. printer-finishings-supported .......................... 27
4.20. printer-number-up-supported ........................... 28
4.21. printer-sides-supported ............................... 28
4.22. printer-media-supported ............................... 29
4.23. printer-media-local-supported ......................... 30
4.24. printer-resolution-supported .......................... 30
4.25. printer-print-quality-supported ....................... 31
4.26. printer-job-priority-supported ........................ 32
4.27. printer-copies-supported .............................. 32
Fleming, McDonald Expires 30 October 2015 [Page 3]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
4.28. printer-job-k-octets-supported ........................ 32
4.29. printer-current-operator .............................. 33
4.30. printer-service-person ................................ 33
4.31. printer-delivery-orientation-supported ................ 34
4.32. printer-stacking-order-supported ...................... 34
4.33. printer-output-features-supported ..................... 35
4.34. printer-aliases ....................................... 36
4.35. printer-device-id ..................................... 36
4.36. printer-device-service-count .......................... 37
4.37. printer-uuid .......................................... 37
4.38. printer-charge-info ................................... 38
4.39. printer-charge-info-uri ............................... 39
4.40. printer-geo-location .................................. 39
4.41. printer-ipp-features-supported ........................ 40
5. Definition of Syntaxes ..................................... 42
6. Definition of Matching Rules ............................... 42
7. IANA Considerations ........................................ 43
7.1. Registration of Attribute Types ........................ 43
7.2. Object Classes and Attribute Types from RFC 3712 ....... 44
8. Internationalization Considerations ........................ 46
9. Security Considerations .................................... 46
10. References ................................................ 47
10.1. Normative References .................................. 47
10.2. Informative References ................................ 49
11. Appendix A - Changes since RFC 3712 ....................... 51
12. Appendix X - Change History ............................... 52
13. Acknowledgments ........................................... 59
14. Authors' Addresses ........................................ 59
Fleming, McDonald Expires 30 October 2015 [Page 4]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
1. Introduction
This document defines several object classes to provide Lightweight
Directory Access Protocol [RFC4510] applications with flexible
options in defining Printer information using LDAP schema. Classes
are provided for defining directory entries with common Printer
information as well as for extending existing directory entries with
SLPv2 [RFC2608], IPP/1.1 [RFC2911], and LPR [RFC1179]
protocol-specific information.
This memo is an independent submission to the RFC Editor Stream by
the Internet Printing Protocol Working Group of the IEEE-ISTO Printer
Working Group, as part of their PWG IPP Everywhere (PWG 5100.14)
project for secure mobile printing with vendor-neutral Client
software.
Please send comments directly to the authors at the addresses listed
in the section "Authors' Addresses".
1.1. Relationship to SLP Printer Service
The schema defined in this document is technically aligned with the
stable IANA-registered 'service:printer:' v2.0 template [SLPPRT20],
for compatibility with already deployed Service Location Protocol
(SLPv2) [RFC2608] service advertising and discovery infrastructure.
The attribute syntaxes are technically aligned with the
'service:printer:' v2.0 template - therefore simpler types are
sometimes used (for example, 'DirectoryString' [RFC4517] rather than
'labeledURI' [RFC2079] for the 'printer-uri' attribute).
1.2. Source of LDAP Printer Attributes
The schema defined in this document is based on: all of the Printer
attributes listed in Appendix E 'Generic Directory Schema' that are
defined in section 4.4 'Printer Description Attributes' of Internet
Printing Protocol/1.1: Model and Semantics [RFC2911]; and selected
Printer attributes defined in the Printer MIB v2 [RFC3805], IEEE-ISTO
PWG Command Set for IEEE 1284 Device ID [PWG5107.2], IEEE-ISTO PWG
IPP Job and Printer Extensions - Set 3 [PWG5100.13], and IEEE-ISTO
PWG IPP Everywhere [PWG5100.14]
See the table of Printer attributes and source documents in section 4
'Definition of Attribute Types' in this document.
Fleming, McDonald Expires 30 October 2015 [Page 5]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
1.3. Source of LDAP Printer Schema OIDs
1.3.1. IBM Assignments for RFC 3712
In March 2000, IBM permanently assigned ASN.1 OIDs to all of the
object classes and attributes types that were defined in the original
LDAP Printer Schema [RFC3712] (see section 7.2).
1.3.2. IEEE-ISTO PWG Assignments
In October 2011, IBM permanently delegated the base ASN.1 OID
"1.3.18.0.2.24.46" to the IEEE-ISTO PWG for use in any PWG project.
In October 2011, the IEEE-ISTO PWG permanently assigned subordinate
ASN.1 OIDs for all of the new attribute types defined in this updated
LDAP Printer Schema (see section 7.1).
1.4. Rationale for Design Choices
1.4.1. Rationale for using DirectoryString Syntax
The attribute syntax 'DirectoryString' (UTF-8 [STD63]) defined in
[RFC4517] is specified for several groups of string attributes that
are defined in this document:
1) URI
- printer-uri, printer-xri-supported, printer-more-info,
printer-charge-info-uri, printer-uuid
The UTF-8 encoding is compatible with deployment of (UTF-8 based)
IRI Internationalized Resource Identifiers (IRIs) [RFC3987].
2) Description
- printer-name, printer-location, printer-info,
printer-make-and-model
The UTF-8 encoding supports descriptions in any language,
conformant with the IETF Policy on Character Sets and Languages
[BCP18].
Note: The printer-natural-language-configured attribute contains
a language tag [BCP47] for these description attributes (for
Fleming, McDonald Expires 30 October 2015 [Page 6]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
example, to support text-to-speech conversions).
3) Keyword
- printer-compression-supported, printer-finishings-supported,
printer-media-supported, printer-media-local-supported,
printer-print-quality-supported
The UTF-8 encoding is compatible with the current IPP/1.1
[RFC2911] definition of the equivalent attributes, most of which
have the IPP/1.1 union syntax 'keyword or name'. The keyword
attributes defined in this document are extensible by
site-specific or vendor-specific 'names' which behave like new
'keywords'
Note: In IPP/1.1, each value is strongly typed over-the-wire as
either 'keyword' or 'name'. This union selector is not preserved
in the definitions of these equivalent LDAP attributes.
1.4.2. Rationale for using caseIgnoreMatch
The EQUALITY matching rule 'caseIgnoreMatch' defined in [RFC4517] is
specified for several groups of string attributes that are defined in
this document:
1) URI
These URI attributes specify EQUALITY matching with
'caseIgnoreMatch' (rather than with 'caseExactMatch') in order to
conform to the spirit of [STD66], which requires case insensitive
matching on the host part of a URI versus case sensitive matching
on the remainder of a URI.
These URI attributes follow existing practice of supporting case
insensitive equality matching for host names in the
associatedDomain attribute defined in [RFC4524].
Either equality matching rule choice would be a compromise:
a) case sensitive whole URI matching can lead to false negative
matches and has been shown to be fragile (given deployed client
applications that 'pretty up' host names displayed and
transferred in URI);
b) case insensitive whole URI matching can lead to false positive
matches, although it is a dangerous practice to publish URI that
differ only by case (for example, in the path elements).
2) Description
Case insensitive equality matching is more user-friendly for
description attributes.
Fleming, McDonald Expires 30 October 2015 [Page 7]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
3) Keyword
Case insensitive equality matching is more user-friendly for
keyword attributes.
4) IEEE 1284 Device ID
Case insensitive equality matching is mandatory for IEEE 1284
Device ID attributes.
1.4.3. Rationale for using caseIgnoreSubstringsMatch
The SUBSTR matching rule 'caseIgnoreSubstringsMatch' defined in
[RFC4517] is specified for several groups of string attributes that
are defined in this document:
1) URI
These URI attributes follow existing practice of supporting case
insensitive equality matching for host names in the
associatedDomain attribute defined in [RFC4524].
2) Description
Support for case insensitive substring matching is more
user-friendly for description attributes.
3) Keyword
Support for case insensitive substring matching is more
user-friendly for keyword attributes.
4) IEEE 1284 Device ID
Support for case insensitive substring matching is mandatory for
IEEE 1284 Device ID attributes.
2. Conventions Used in This Document
2.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Fleming, McDonald Expires 30 October 2015 [Page 8]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
2.2. LDAP Schema Descriptions
Schema definitions are provided using LDAP [RFC4510] description
formats. Definitions provided here are formatted (line wrapped) for
readability.
2.3. Abbreviations
This document makes use of the following abbreviations (given with
their expanded forms and references for further reading):
IANA - Internet Assigned Numbers Authority
<http://www.iana.org>
IEEE - Institute of Electrical and Electronics Engineers
<http://www.ieee.org>
IPP - Internet Printing Protocol [RFC2911] and [PWG5100.12]
<http://www.pwg.org/ipp/>
ISTO - IEEE Industry Standards and Technology Organization
<http://www.ieee-isto.org/>
PWG - IEEE-ISTO Printer Working Group
<http://www.pwg.org>
RFC - Request for Comments
<http://www.rfc-editor.org/rfc.html>
TLS - Transport Layer Security [RFC5246]
URI - Uniform Resource Identifier [STD66]
URL - Uniform Resource Locator [STD66]
UTF-8 - Unicode Transformation Format - 8-bit [STD63]
Fleming, McDonald Expires 30 October 2015 [Page 9]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
3. Definition of Object Classes
We define the following LDAP object classes for use with both generic
Printer related information and services specific to SLPv2 [RFC2608],
IPP/1.1 [RFC2911], and LPR [RFC1179].
slpServicePrinter - auxiliary class for SLP registered Printers
printerAbstract - abstract class for all Printer classes
printerService - structural class for Printers
printerServiceAuxClass - auxiliary class for Printers
printerIPP - auxiliary class for IPP Printers
printerLPR - auxiliary class for LPR Printers
The following are some examples of how applications could choose to
use these classes when creating directory entries:
1) Use printerService for directory entries containing common
Printer information.
2) Use both printerService and slpServicePrinter for directory
entries containing common Printer information for SLP registered
Printers.
3) Use printerService, printerLPR and printerIPP for directory
entries containing common Printer information for Printers that
support both LPR and IPP.
4) Use printerServiceAuxClass and object classes not defined by this
document for directory entries containing common Printer
information. In this example, printerServiceAuxClass is used for
extending other structural classes defining Printer information
with common printer information defined in this document.
Refer to Section 4 for definition of attribute types referenced by
these object classes. We use attribute names instead of OIDs in
object class definitions for clarity. Some attribute names described
in [RFC2911] have been prefixed with 'printer-' as recommended in
[RFC2926] and [SLPPRT20].
Fleming, McDonald Expires 30 October 2015 [Page 10]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
3.1. slpServicePrinter
( 1.3.18.0.2.6.254
NAME 'slpServicePrinter'
DESC 'Service Location Protocol (SLP) information.'
AUXILIARY
SUP slpService
)
This auxiliary class defines Service Location Protocol (SLPv2)
[RFC2608] specific information. It MAY be used to create new or
extend existing directory entries with SLP 'service:printer' abstract
service type information as defined in [SLPPRT20]. This object class
is derived from 'slpService', the parent class for all SLP services,
defined in [RFC2926].
3.2. printerAbstract
( 1.3.18.0.2.6.258
NAME 'printerAbstract'
DESC 'Printer related information.'
ABSTRACT
SUP top
MAY ( printer-name $
printer-natural-language-configured $
printer-location $
printer-info $
printer-more-info $
printer-make-and-model $
printer-multiple-document-jobs-supported $
printer-charset-configured $
printer-charset-supported $
printer-generated-natural-language-supported $
printer-document-format-supported $
printer-color-supported $
printer-compression-supported $
printer-pages-per-minute $
printer-pages-per-minute-color $
printer-finishings-supported $
printer-number-up-supported $
printer-sides-supported $
printer-media-supported $
printer-media-local-supported $
printer-resolution-supported $
printer-print-quality-supported $
printer-job-priority-supported $
printer-copies-supported $
Fleming, McDonald Expires 30 October 2015 [Page 11]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
printer-job-k-octets-supported $
printer-current-operator $
printer-service-person $
printer-delivery-orientation-supported $
printer-stacking-order-supported $
printer-output-features-supported $
printer-device-id $
printer-device-service-count $
printer-uuid $
printer-charge-info $
printer-charge-info-uri $
printer-geo-location )
)
This abstract class defines Printer information. It is a base class
for deriving other Printer related classes, such as, but not limited
to, classes defined in this document. It defines a common set of
printer attributes that are not specific to any one type of service,
protocol or operating system.
3.3. printerService
( 1.3.18.0.2.6.255
NAME 'printerService'
DESC 'Printer information.'
STRUCTURAL
SUP printerAbstract
MAY ( printer-uri $
printer-xri-supported )
)
This structural class defines Printer information. It is derived
from class printerAbstract and thus inherits common Printer
attributes. This class can be used with or without auxiliary classes
to define printer information. Auxiliary classes can be used to
extend the common printer information with protocol, service or
operating system specific information.
Note: When extending other structural classes with auxiliary
classes, printerService SHOULD NOT be used.
3.4. printerServiceAuxClass
( 1.3.18.0.2.6.257
NAME 'printerServiceAuxClass'
DESC 'Printer information.'
AUXILIARY
Fleming, McDonald Expires 30 October 2015 [Page 12]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
SUP printerAbstract
MAY ( printer-uri $
printer-xri-supported )
)
This auxiliary class defines Printer information. It is derived from
class printerAbstract and thus inherits common Printer attributes.
3.5. printerIPP
( 1.3.18.0.2.6.256
NAME 'printerIPP'
DESC 'Internet Printing Protocol (IPP) information.'
AUXILIARY
SUP top
MAY ( printer-ipp-versions-supported $
printer-ipp-features-supported $
printer-multiple-document-jobs-supported )
)
This auxiliary class defines Internet Printing Protocol (IPP/1.1)
[RFC2911] information. It is used to extend structural classes with
IPP specific Printer information.
Note: See IPP URL Scheme [RFC3510] and IPP over HTTPS Transport
Binding and 'ipps' URI Scheme [IPPSURI] for conforming URI for IPP
Printers.
3.6. printerLPR
( 1.3.18.0.2.6.253
NAME 'printerLPR'
DESC 'LPR information.'
AUXILIARY
SUP top
MUST ( printer-name )
MAY ( printer-aliases)
)
This auxiliary class defines LPR [RFC1179] information. It is used
to identify directory entries that support LPR.
Fleming, McDonald Expires 30 October 2015 [Page 13]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
4. Definition of Attribute Types
The following attribute types are referenced by the object classes
defined in Section 3.
The following attribute types reference syntax OIDs defined in
Section 3 of [RFC4517] (see Section 5 'Definition of Syntaxes'
below).
The following attribute types reference matching rule names (instead
of OIDs) for clarity (see Section 6 below). For optional attributes,
if the Printer information is not known, the attribute value SHOULD
NOT be set. In the following definitions, referenced matching rules
are defined in Section 4 of [RFC4517] and discussed in Section 6
'Definition of Matching Rules' later in this document.
Note: For compatibility with existing implementations of [RFC3712]
and underlying string length limits in [RFC2707], [RFC2911],
[RFC3805], [PWG5107.2], [PWG5100.13], and [PWG5100.14],
implementations of the attributes defined in this document SHOULD NOT
exceed those underlying string length limits (to avoid truncation and
false matches).
Note: For interoperability and consistent text display, values of
attributes defined in this document: (a) SHOULD be normalized as
recommended in Unicode Format for Network Interchange [RFC5198]; (b)
SHOULD NOT contain DEL or any C0 or C1 control characters except for
HT, CR, and LF; (c) SHOULD only contain CR and LF characters together
(not as singletons); and SHOULD NOT contain HT, CR, or LF characters
in names, e.g., printer-name and printer-aliases.
Note: Some of the following attributes are described as 'List of
xxx' (using a comma as the member delimiter). Some other attributes
are described as 'One of xxx' (single-valued). In all cases, any
attribute can have multiple values represented as multiple instances,
except where explictly restricted in syntax to be single-valued.
Note: Values of the string attributes printer-xri-supported and
printer-resolution-supported use different field delimiters ('<' and
'>', respectively). These two field delimiters are different for
compatibility with the corresponding attributes in the
IANA-registered SLP 'service:printer:' v2.0 template [SLPPRT20],
which was defined before the original LDAP Printer Schema [RFC3712]
was written.
The following table is a summary of the attribute names defined by
this document and their corresponding source document names as
defined in [RFC2911], [RFC3805], [PWG5107.2], or [PWG5100.13]. Some
source attribute names have been prefixed with 'printer-' as
Fleming, McDonald Expires 30 October 2015 [Page 14]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
recommended in [RFC2926], to address the flat namespace for LDAP
identifiers.
LDAP & SLP Printer Schema Source Document and Attribute Name
------------------------------ -------------------------------------
*** IPP/1.1 and Semantics Model [RFC2911]
printer-uri
printer-xri-supported
[printer-uri-supported]
[uri-authentication-supported]
[uri-security-supported]
printer-name printer-name
printer-natural-language-configured
natural-language-configured
printer-location printer-location
printer-info printer-info
printer-more-info printer-more-info
printer-make-and-model printer-make-and-model
printer-ipp-versions-supported ipp-versions-supported
printer-multiple-document-jobs-supported
multiple-document-jobs-supported
printer-charset-configured charset-configured
printer-charset-supported charset-supported
printer-generated-natural-language-supported
generated-natural-language-supported
printer-document-format-supported
document-format-supported
printer-color-supported color-supported
printer-compression-supported compression-supported
printer-pages-per-minute pages-per-minute
printer-pages-per-minute-color pages-per-minute-color
printer-finishings-supported finishings-supported
printer-number-up-supported number-up-supported
printer-sides-supported sides-supported
printer-media-supported media-supported
printer-media-local-supported [site names from IPP media-supported]
printer-resolution-supported printer-resolution-supported
printer-print-quality-supported print-quality-supported
printer-job-priority-supported job-priority-supported
printer-copies-supported copies-supported
printer-job-k-octets-supported job-k-octets-supported
*** Printer MIB v2 [RFC3805]
printer-current-operator prtGeneralCurrentOperator
printer-service-person prtGeneralServicePerson
printer-delivery-orientation-supported
prtOutputPageDeliveryOrientation
printer-stacking-order-supported
prtOutputStackingOrder
printer-output-features-supported
[prtOutputBursting]
Fleming, McDonald Expires 30 October 2015 [Page 15]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
[prtOutputDecollating]
[prtOutputPageCollated]
[prtOutputOffsetStacking]
printer-aliases prtGeneralPrinterName
*** Cmd Set 1284 Device ID [PWG5107.2]
printer-device-id printer-device-id
*** IPP Job/Printer Ext Set3 [PWG5100.13]
printer-device-service-count device-service-count
printer-uuid printer-uuid
printer-charge-info printer-charge-info
printer-charge-info-uri printer-charge-info-uri
printer-geo-location printer-geo-location
printer-ipp-features-supported ipp-features-supported
4.1. printer-uri
( 1.3.18.0.2.4.1140
NAME 'printer-uri'
DESC 'A URI supported by this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
)
If the printer-xri-supported LDAP attribute is implemented, then this
printer-uri value MUST be listed in printer-xri-supported.
See [STD66] for details of URI syntax.
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 1023 octets in length.
Note: LDAP application clients SHOULD NOT attempt to use malformed
URI values read from this attribute. LDAP administrative clients
SHOULD not write malformed URI values into this attribute.
Note: See IPP URL Scheme [RFC3510] and IPP over HTTPS Transport
Binding and 'ipps' URI Scheme [IPPSURI] for conforming URI for IPP
Printers.
Note: For SLP registered Printers, the LDAP printer-uri attribute
SHOULD be set to the value of the SLP-registered URL of the Printer,
for interworking with SLPv2 [RFC2608] service discovery.
Note: See Sections 1.1, 1.2, and 1.3 for rationale for design
choices.
Fleming, McDonald Expires 30 October 2015 [Page 16]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
4.2. printer-xri-supported
( 1.3.18.0.2.4.1107
NAME 'printer-xri-supported'
DESC 'An XRI (extended resource identifier) supported by this
Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
An XRI (extended resource identifier) supported by this Printer.
Each value of this attribute MUST consist of a URI (uniform resource
identifier) followed by (optional) authentication and security
fields.
Each XRI field MUST be delimited by '<', with optional trailing
whitespace. For example:
'uri=ipp://example.com/ipp< auth=digest< sec=tls<'
'uri=ipps://example.com/ipp< auth=digest< sec=tls<'
'uri=lpr://example.com/lpr< auth=none< sec=none<'
'uri=mailto:printer@example.com< auth=none< sec=none<'
Note: See the note in section 4 about the different field delimiters
used in the printer-xri-supported and printer-resolution-supported
attributes ('<' and '>', respectively), chosen for compatibility with
the IANA-registered SLP 'service:printer:' v2.0 template [SLPPRT20].
Note: Multiple values for this attribute are represented as multiple
instances of this attribute.
See [STD66] for details of URI syntax.
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 1023 octets in length.
Note: LDAP application clients SHOULD NOT attempt to use malformed
URI values read from this attribute. LDAP administrative clients
SHOULD not write malformed URI values into this attribute.
Note: This attribute is based on the IPP/1.1 [RFC2911] attributes
'printer-uri-supported', 'uri-authentication-supported', and
'uri-security-supported' (called the 'Three Musketeers' because they
are parallel, ordered attributes). This attribute unfolds those
IPP/1.1 attributes and thus avoids the ordering (and same number of
values) constraints of the IPP/1.1 separate attributes.
Fleming, McDonald Expires 30 October 2015 [Page 17]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
Defined keywords for fields include:
'uri' (IPP 'printer-uri-supported')
'auth' (IPP 'uri-authentication-supported')
'sec' (IPP 'uri-security-supported')
A missing 'auth' field SHOULD be interpreted to mean 'none'. Per
IPP/1.1 [RFC2911], IPP Job and Printer Extensions - Set 3
[PWG5100.13], and IANA IPP Registry [IANAIPP], defined values of the
'auth' field include:
'none' (no authentication for this URI)
'requesting-user-name' (from operation request)
'basic' (HTTP/1.1 Basic [RFC2617] and [RFC7235])
'digest' (HTTP/1.1 Digest [RFC2617] and [RFC7235])
'certificate' (X.509 Certificate [RFC5280] and [RFC6818])
'negotiate' (HTTP/1.1 Negotiate [RFC4559])
The 'certificate' value refers to the IPP Client certificate
extracted from the TLS session.
A missing 'sec' field SHOULD be interpreted to mean 'none'. Per
IPP/1.1 [RFC2911] and IANA IPP Registry [IANAIPP], defined values of
the 'sec' field include:
'none' (no security for this URI)
'ssl3' (Netscape SSL3)
'tls' (IETF TLS, [RFC5246])
Note: The syntax and delimiter for this attribute are aligned with
the equivalent attribute in the 'service:printer:' v2.0 template
[SLPPRT20]. Whitespace is permitted after (but not before) the
delimiter '<'.
Note: See IPP URL Scheme [RFC3510] and IPP over HTTPS Transport
Binding and 'ipps' URI Scheme [IPPSURI] for conforming URI for IPP
Printers.
Note: See Sections 1.1, 1.2, and 1.3 for rationale for design
choices.
4.3. printer-name
( 1.3.18.0.2.4.1135
NAME 'printer-name'
DESC 'The site-specific administrative name of this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
Fleming, McDonald Expires 30 October 2015 [Page 18]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
)
Values of this attribute SHOULD be specified in the language
specified in printer-natural-language-configured (for example, to
support text-to-speech conversions), although the Printer's name MAY
be specified in any language.
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 255 octets in length.
Note: This name can be the last part of the Printer's URI or it can
be completely unrelated. This name can contain characters that are
not allowed in a conventional URI (see [STD66]).
Note: For interoperability, values of this attribute: (a) SHOULD be
normalized as recommended in Unicode Format for Network Interchange
[RFC5198]; and (b) SHOULD NOT contain DEL or any C0 or C1 control
characters.
4.4. printer-natural-language-configured
( 1.3.18.0.2.4.1119
NAME 'printer-natural-language-configured'
DESC 'The configured natural language for LDAP attributes of
syntax DirectoryString (UTF-8) in this directory entry.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
)
Also, a possible natural language for IPP protocol string attributes
set by operator, system administrator, or manufacturer. Also, the
(declared) natural language of the printer-name, printer-location,
printer-info, and printer-make-and-model attributes of this Printer.
Values of language tags MUST conform to Tags for Identifying
Languages [BCP47]. For example:
'en-us' (English as spoken in the US)
'fr-fr' (French as spoken in France)
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 63 octets in length.
Note: For compatibility with IPP/1.1 [RFC2911], language tags in
this attribute SHOULD be lowercase normalized.
Fleming, McDonald Expires 30 October 2015 [Page 19]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
4.5. printer-location
( 1.3.18.0.2.4.1136
NAME 'printer-location'
DESC 'The physical location of this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
)
For example:
'Room 123A'
'Second floor of building XYZ'
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 127 octets in length.
Note: For interoperability and consistent text display, values of
this attribute: (a) SHOULD be normalized as recommended in Unicode
Format for Network Interchange [RFC5198]; (b) SHOULD NOT contain DEL
or any C0 or C1 control characters except for HT, CR, and LF; and (c)
SHOULD only contain CR and LF characters together (not as
singletons).
4.6. printer-info
( 1.3.18.0.2.4.1139
NAME 'printer-info'
DESC 'Descriptive information about this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
)
For example:
'This Printer can be used for printing color transparencies for
HR presentations'
'Out of courtesy for others, please print only small (1-5 page)
jobs at this Printer'
'This Printer is going away on July 1, 1997, please find a new
Printer'
Fleming, McDonald Expires 30 October 2015 [Page 20]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 127 octets in length.
Note: For interoperability and consistent text display, values of
this attribute: (a) SHOULD be normalized as recommended in Unicode
Format for Network Interchange [RFC5198]; (b) SHOULD NOT contain DEL
or any C0 or C1 control characters except for HT, CR, and LF; and (c)
SHOULD only contain CR and LF characters together (not as
singletons).
4.7. printer-more-info
( 1.3.18.0.2.4.1134
NAME 'printer-more-info'
DESC 'A URI for more information about this specific Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
)
For example, this could be an HTTP URI referencing an HTML page
accessible to a Web Browser. The information obtained from this URI
is intended for end user consumption.
See [STD66] for details of URI syntax.
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 1023 octets in length.
Note: LDAP application clients SHOULD NOT attempt to use malformed
URI values read from this attribute. LDAP administrative clients
SHOULD not write malformed URI values into this attribute.
Note: See Sections 1.1, 1.2, and 1.3 for rationale for design
choices.
4.8. printer-make-and-model
( 1.3.18.0.2.4.1138
NAME 'printer-make-and-model'
DESC 'Make and model of this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
Fleming, McDonald Expires 30 October 2015 [Page 21]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
)
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 127 octets in length.
Note: The Printer manufacturer MAY initially populate this
attribute.
Note: For interoperability and consistent text display, values of
this attribute: (a) SHOULD be normalized as recommended in Unicode
Format for Network Interchange [RFC5198]; (b) SHOULD NOT contain DEL
or any C0 or C1 control characters except for HT, CR, and LF; and (c)
SHOULD only contain CR and LF characters together (not as
singletons).
4.9. printer-ipp-versions-supported
( 1.3.18.0.2.4.1133
NAME 'printer-ipp-versions-supported'
DESC 'List of IPP versions supported by this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
Comma-delimited list of IPP versions supported by this Printer. For
example:
'1.1,2.0'
Note: Length overflow in values of this attribute MUST be handled by
multiple instances of this attribute, i.e., individual
comma-delimited list members MUST NOT be truncated.
The IPP protocol version(s) MUST include major and minor versions,
i.e., the exact version numbers for which this Printer implementation
meets the IPP version-specific conformance requirements and
registered in the IANA IPP Registry [IANAIPP].
IANA-registered versions of IPP currently are:
'1.0' (IPP/1.0 [RFC2566], OBSOLETE)
'1.1' (IPP/1.1 [RFC2911])
'2.0' (IPP/2.0 [PWG5100.12])
'2.1' (IPP/2.1 [PWG5100.12])
'2.2' (IPP/2.2 [PWG5100.12])
Fleming, McDonald Expires 30 October 2015 [Page 22]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
4.10. printer-multiple-document-jobs-supported
( 1.3.18.0.2.4.1132
NAME 'printer-multiple-document-jobs-supported'
DESC 'Indicates whether or not this Printer supports more than one
document per job.'
EQUALITY booleanMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.7
SINGLE-VALUE
)
4.11. printer-charset-configured
( 1.3.18.0.2.4.1109
NAME 'printer-charset-configured'
DESC 'The configured charset for IPP protocol values of error
and status messages generated by this Printer.'
EQUALITY caseIgnoreMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
)
Also, a possible charset for IPP protocol string attributes set by
operator, system administrator, or manufacturer. For example:
'utf-8' (ISO 10646/Unicode in UTF-8 transform [STD63])
'iso-8859-1' (Latin1)
Values of charset tags SHOULD be defined in the IANA Registry of
Character Sets [IANACHAR] (see also [BCP19]) and the '(preferred MIME
name)' SHOULD be used as the charset tag in this attribute.
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 63 octets in length.
Note: For compatibility with IPP/1.1 [RFC2911], charset tags in this
attribute SHOULD be lowercase normalized.
4.12. printer-charset-supported
( 1.3.18.0.2.4.1131
NAME 'printer-charset-supported'
DESC 'One of the charsets supported for IPP protocol values of
IPP string attributes that correspond to attributes of
syntax DirectoryString (UTF-8) for this directory entry.'
Fleming, McDonald Expires 30 October 2015 [Page 23]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
EQUALITY caseIgnoreMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
One of the charsets supported for IPP protocol string attributes that
correspond to attributes of syntax DirectoryString (UTF-8) for this
directory entry. For example:
'iso-8859-1' (ISO Latin1)
'utf-8' (UTF-8 [STD63])
Note: Multiple values for this attribute are represented as multiple
instances of this attribute.
Values of charset tags SHOULD be defined in the IANA Registry of
Character Sets [IANACHAR] (see also [BCP19]) and the '(preferred MIME
name)' SHOULD be used as the charset tag in this attribute.
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 63 octets in length.
Note: For compatibility with IPP/1.1 [RFC2911], charset tags in this
attribute SHOULD be lowercase normalized.
4.13. printer-generated-natural-language-supported
( 1.3.18.0.2.4.1137
NAME 'printer-generated-natural-language-supported'
DESC 'One of the natural languages supported for LDAP attributes of
syntax DirectoryString (UTF-8) in this directory entry.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
Values of language tags SHOULD conform to Tags for Identifying
Languages [BCP47]. For example:
'en-us' (English as spoken in the US)
'fr-ca' (French as spoken in Canada)
Note: Multiple values for this attribute are represented as multiple
instances of this attribute.
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 63 octets in length.
Note: For compatibility with IPP/1.1 [RFC2911], language tags in
this attribute SHOULD be lowercase normalized.
Fleming, McDonald Expires 30 October 2015 [Page 24]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
4.14. printer-document-format-supported
( 1.3.18.0.2.4.1130
NAME 'printer-document-format-supported'
DESC 'One of the source document formats which can be interpreted
and printed by this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
Values of document formats SHOULD be MIME media types defined in the
IANA Registry of MIME Media Types [IANAMIME] (see also [BCP13]).
For example:
'application/postscript' (Adobe PostScript)
'text/plain' (plain text)
Note: Multiple values for this attribute are represented as multiple
instances of this attribute.
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 255 octets in length.
4.15. printer-color-supported
( 1.3.18.0.2.4.1129
NAME 'printer-color-supported'
DESC 'Indicates whether this Printer is capable of any type of color
printing at all, including highlight color.'
EQUALITY booleanMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.7
SINGLE-VALUE
)
4.16. printer-compression-supported
( 1.3.18.0.2.4.1128
NAME 'printer-compression-supported'
DESC 'List of compression algorithms supported by this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
Fleming, McDonald Expires 30 October 2015 [Page 25]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
)
Comma-delimited list of compression algorithms supported by this
Printer. For example:
'none'
'deflate,gzip'
Note: Length overflow in values of this attribute MUST be handled by
multiple instances of this attribute, i.e., individual
comma-delimited list members MUST NOT be truncated.
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 255 octets in length.
Values defined in IPP/1.1 [RFC2911] and recorded in the IANA IPP
Registry [IANAIPP] include:
'none' (no compression is used)
'deflate' (public domain ZIP described in [RFC1951])
'gzip' (GNU ZIP described in [RFC1952])
'compress' (UNIX compression described in [RFC1977])
4.17. printer-pages-per-minute
( 1.3.18.0.2.4.1127
NAME 'printer-pages-per-minute'
DESC 'The nominal number of pages per minute which can be output by
this Printer.'
EQUALITY integerMatch
ORDERING integerOrderingMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.27
SINGLE-VALUE
)
This attribute is informative, not a service guarantee. Typically,
it is the value used in marketing literature to describe this
Printer. For example, the value for a simplex or black-and-white
print mode.
4.18. printer-pages-per-minute-color
( 1.3.18.0.2.4.1126
NAME 'printer-pages-per-minute-color'
DESC 'The nominal number of color pages per minute which can be
output by this Printer.'
EQUALITY integerMatch
Fleming, McDonald Expires 30 October 2015 [Page 26]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
ORDERING integerOrderingMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.27
SINGLE-VALUE
)
This attribute is informative, not a service guarantee. Typically,
it is the value used in marketing literature to describe this
Printer.
4.19. printer-finishings-supported
( 1.3.18.0.2.4.1125
NAME 'printer-finishings-supported'
DESC 'List of finishing operations supported by this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
Comma-delimited list of finishing operations supported by this
Printer. For example:
'staple'
'staple,punch,bind'
Note: Length overflow in values of this attribute MUST be handled by
multiple instances of this attribute, i.e., individual
comma-delimited list members MUST NOT be truncated.
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 255 octets in length.
Values defined in IPP/1.1 [RFC2911] and recorded in the IANA IPP
Registry [IANAIPP] include:
'none', 'staple', 'punch', 'cover', 'bind', 'saddle-stitch',
'edge-stitch', 'staple-top-left', 'staple-bottom-left',
'staple-top-right', 'staple-bottom-right', 'edge-stitch-left',
'edge-stitch-top', 'edge-stitch-right', 'edge-stitch-bottom',
'staple-dual-left', 'staple-dual-top', 'staple-dual-right',
'staple-dual-bottom'.
Note: Implementations MAY support other values.
Fleming, McDonald Expires 30 October 2015 [Page 27]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
4.20. printer-number-up-supported
( 1.3.18.0.2.4.1124
NAME 'printer-number-up-supported'
DESC 'Maximum number of print-stream pages that can be imposed upon a
single side of an instance of selected medium by this Printer.'
EQUALITY integerMatch
ORDERING integerOrderingMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.27
SINGLE-VALUE
)
Maximum number of print-stream pages that can be imposed upon a
single side of an instance of a selected medium by this Printer. For
example:
'1'
'4'
Note: Values of this attribute differ from the corresponding IPP
attribute, in that only the maximum number-up is mapped from the
corresponding IPP attribute 'number-up-supported' defined in
[RFC2911].
4.21. printer-sides-supported
( 1.3.18.0.2.4.1123
NAME 'printer-sides-supported'
DESC 'List of impression sides (one or two) and the two-sided
impression rotations supported by this Printer.'
EQUALITY caseIgnoreMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
Comma-delimited list of impression sides (one or two) and the
two-sided impression rotations supported by this Printer. For
example:
'one-sided'
'one-sided,two-sided-short-edge'
Note: Length overflow in values of this attribute MUST be handled by
multiple instances of this attribute, i.e., individual
comma-delimited list members MUST NOT be truncated.
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 255 octets in length.
Fleming, McDonald Expires 30 October 2015 [Page 28]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
Values defined in IPP/1.1 [RFC2911] and recorded in the IANA IPP
Registry [IANAIPP] are:
'one-sided'
'two-sided-long-edge'
'two-sided-short-edge'
4.22. printer-media-supported
( 1.3.18.0.2.4.1122
NAME 'printer-media-supported'
DESC 'One of the names/sizes/types/colors of the media supported by
this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
Values SHOULD conform to PWG Media Standardized Names [PWG5101.1].
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 255 octets in length.
Values of standardized media size names defined in [PWG5101.1] and
recorded in the IANA IPP Registry [IANAIPP] include:
'na_letter_8.5x11in'
'iso_a4_210x297mm'
Values of standardized media types defined in [PWG5101.1] and
recorded in the IANA IPP Registry [IANAIPP] include:
'envelope'
'stationery'
Values of standardized media colors defined in [PWG5101.1] and
recorded in the IANA IPP Registry [IANAIPP] include:
'white'
'blue'
Note: Multiple values for this attribute are represented as multiple
instances of this attribute.
Fleming, McDonald Expires 30 October 2015 [Page 29]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
4.23. printer-media-local-supported
( 1.3.18.0.2.4.1117
NAME 'printer-media-local-supported'
DESC 'One of the site-specific media supported by this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
Values SHOULD conform to PWG Media Standardized Names [PWG5101.1].
For example:
'custom_purchasing-form_8.5x11in' (site-specific name)
Note: Multiple values for this attribute are represented as multiple
instances of this attribute.
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 255 octets in length.
4.24. printer-resolution-supported
( 1.3.18.0.2.4.1121
NAME 'printer-resolution-supported'
DESC 'One of the resolutions supported for printing documents by this
Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
Each resolution value MUST be a string containing 3 fields:
1) Cross feed direction resolution (positive integer);
2) Feed direction resolution (positive integer);
3) Unit - 'dpi' (dots per inch) or 'dpcm' (dots per centimeter).
Each resolution field MUST be delimited by '>', with optional
trailing whitespace. For example:
'300> 300> dpi>'
'600> 600> dpi>'
Note: See the note in section 4 about the different field delimiters
used in the printer-xri-supported and printer-resolution-supported
attributes ('<' and '>', respectively), chosen for compatibility with
Fleming, McDonald Expires 30 October 2015 [Page 30]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
the IANA-registered SLP 'service:printer:' v2.0 template [SLPPRT20].
Note: Multiple values for this attribute are represented as multiple
instances of this attribute.
Note: This attribute is based on 'printer-resolution-supported'
defined in IPP/1.1 [RFC2911] (which has a binary complex encoding)
derived from 'prtMarkerAddressabilityFeedDir',
'prtMarkerAddressabilityXFeedDir', and 'prtMarkerAddressabilityUnit'
defined in the Printer MIB v2 [RFC3805] (which have integer
encodings).
Note: The syntax and delimiter for this attribute are aligned with
the equivalent attribute in the 'service:printer:' v2.0 template
[SLPPRT20]. Whitespace is permitted after (but not before) the
delimiter '>'.
4.25. printer-print-quality-supported
( 1.3.18.0.2.4.1120
NAME 'printer-print-quality-supported'
DESC 'List of print qualities supported for printing documents on
this Printer.'
EQUALITY caseIgnoreMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
Comma-delimited list of print qualities supported for printing
documents on this Printer. For example:
'unknown'
'draft,normal,high'
Note: Length overflow in values of this attribute MUST be handled by
multiple instances of this attribute, i.e., individual
comma-delimited list members MUST NOT be truncated.
Values defined in IPP/1.1 [RFC2911] and recorded in the IANA IPP
Registry [IANAIPP] include:
'draft'
'normal'
'high'
Note: The value 'unknown' MUST only be reported if the corresponding
IPP attribute is not present, i.e., the value 'unknown' is an
artifact of this LDAP mapping.
Fleming, McDonald Expires 30 October 2015 [Page 31]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
4.26. printer-job-priority-supported
( 1.3.18.0.2.4.1110
NAME 'printer-job-priority-supported'
DESC 'Indicates the number of job priority levels supported by this
Printer.'
EQUALITY integerMatch
ORDERING integerOrderingMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.27
SINGLE-VALUE
)
An IPP/1.1 [RFC2911] conformant Printer, which supports job priority,
always supports a full range of priorities from '1' to '100' (to
ensure consistent behavior), therefore this attribute describes the
'granularity' of priority supported. Values of this attribute are
from '1' to '100'.
4.27. printer-copies-supported
( 1.3.18.0.2.4.1118
NAME 'printer-copies-supported'
DESC 'The maximum number of copies of a document that can be printed
as a single job on this Printer.'
EQUALITY integerMatch
ORDERING integerOrderingMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.27
SINGLE-VALUE
)
A positive value indicates the maximum supported copies. A value of
'0' indicates no maximum limit. A value of '-1' indicates 'unknown'.
Note: The syntax and values for this attribute are aligned with the
equivalent attribute in the 'service:printer:' v2.0 template
[SLPPRT20].
4.28. printer-job-k-octets-supported
( 1.3.18.0.2.4.1111
NAME 'printer-job-k-octets-supported'
DESC 'The maximum size in kilobytes (1,024 octets actually) incoming
print job that this Printer will accept.'
EQUALITY integerMatch
ORDERING integerOrderingMatch
Fleming, McDonald Expires 30 October 2015 [Page 32]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
SYNTAX 1.3.6.1.4.1.1466.115.121.1.27
SINGLE-VALUE
)
A positive value indicates the maximum supported job size. A value
of '0' indicates no maximum limit. A value of '-1' indicates
'unknown'.
Note: The syntax and values for this attribute are aligned with the
equivalent attribute in the 'service:printer:' v2.0 template
[SLPPRT20].
4.29. printer-current-operator
( 1.3.18.0.2.4.1112
NAME 'printer-current-operator'
DESC 'The identity of the current human operator responsible for
operating this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
)
The value of this attribute SHOULD include information that would
enable other humans to reach the operator, such as a telephone
number.
Note: For interoperability and consistent text display, values of
this attribute: (a) SHOULD be normalized as recommended in Unicode
Format for Network Interchange [RFC5198]; (b) SHOULD NOT contain DEL
or any C0 or C1 control characters except for HT, CR, and LF; and (c)
SHOULD only contain CR and LF characters together (not as
singletons).
4.30. printer-service-person
( 1.3.18.0.2.4.1113
NAME 'printer-service-person'
DESC 'The identity of the current human service person responsible
for servicing this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
)
Fleming, McDonald Expires 30 October 2015 [Page 33]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
The value of this attribute SHOULD include information that would
enable other humans to reach the service person, such as a telephone
number.
Note: For interoperability and consistent text display, values of
this attribute: (a) SHOULD be normalized as recommended in Unicode
Format for Network Interchange [RFC5198]; (b) SHOULD NOT contain DEL
or any C0 or C1 control characters except for HT, CR, and LF; and (c)
SHOULD only contain CR and LF characters together (not as
singletons).
4.31. printer-delivery-orientation-supported
( 1.3.18.0.2.4.1114
NAME 'printer-delivery-orientation-supported'
DESC 'List of delivery orientations of pages as they are printed
and ejected supported by this Printer.'
EQUALITY caseIgnoreMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
Comma-delimited list of delivery orientations of pages as they are
printed and ejected supported by this Printer. For example:
'unknown'
'face-up,face-down'
Values defined in Printer MIB v2 [RFC3805] for
prtOutputPageDeliveryOrientation are:
'face-up'
'face-down'
Note: The value 'unknown' MUST only be reported if the corresponding
Printer MIB attribute is not present, i.e., the value 'unknown' is an
artifact of this LDAP mapping.
Note: The syntax and values for this attribute are aligned with the
equivalent attribute in the 'service:printer:' v2.0 template
[SLPPRT20].
4.32. printer-stacking-order-supported
( 1.3.18.0.2.4.1115
NAME 'printer-stacking-order-supported'
DESC 'List of stacking orders of pages as they are printed and
Fleming, McDonald Expires 30 October 2015 [Page 34]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
ejected supported by this Printer.'
EQUALITY caseIgnoreMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
Comma-delimited list of stacking orders of pages as they are printed
and ejected supported by this Printer. For example:
'unknown'
'first-to-last'
'first-to-last,last-to-first'
Values defined in Printer MIB v2 [RFC3805] for prtOutputStackingOrder
are:
'first-to-last'
'last-to-first'
Note: The value 'unknown' MUST only be reported if the corresponding
Printer MIB attribute is not present, i.e., the value 'unknown' is an
artifact of this LDAP mapping.
Note: The syntax and values for this attribute are aligned with the
equivalent attribute in the 'service:printer:' v2.0 template
[SLPPRT20].
4.33. printer-output-features-supported
( 1.3.18.0.2.4.1116
NAME 'printer-output-features-supported'
DESC 'List of output features supported by this Printer.'
EQUALITY caseIgnoreMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
Comma-delimited list of output features supported by this Printer.
For example:
'unknown'
'bursting,decollating'
'offset-stacking'
Note: Length overflow in values of this attribute MUST be handled by
multiple instances of this attribute, i.e., individual
comma-delimited list members MUST NOT be truncated.
Values defined in Printer MIB v2 [RFC3805] for prtOutputBursting,
prtOutputDecollating, prtOutputPageCollated, and
prtOutputOffsetStacking are:
Fleming, McDonald Expires 30 October 2015 [Page 35]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
'bursting'
'decollating'
'page-collating'
'offset-stacking'
Note: The value 'unknown' MUST only be reported if the corresponding
Printer MIB attributes are not present, i.e., the value 'unknown' is
an artifact of this LDAP mapping.
Note: The syntax and values for this attribute are aligned with the
equivalent attribute in the 'service:printer:' v2.0 template
[SLPPRT20].
Note: Implementations MAY support other values.
4.34. printer-aliases
( 1.3.18.0.2.4.1108
NAME 'printer-aliases'
DESC 'One of the site-specific administrative names of this Printer
in addition to the value specified for printer-name.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
Values of this attribute SHOULD be specified in the language
specified in printer-natural-language-configured (for example, to
support text-to-speech conversions), although the Printer's alias MAY
be specified in any language.
Note: Multiple values for this attribute are represented as multiple
instances of this attribute.
Note: For compatibility with IPP/1.1 [RFC2911], values of this
attribute SHOULD NOT exceed 255 octets in length.
Note: For interoperability, values of this attribute: (a) SHOULD be
normalized as recommended in Unicode Format for Network Interchange
[RFC5198]; and (b) SHOULD NOT contain DEL or any C0 or C1 control
characters.
4.35. printer-device-id
( 1.3.18.0.2.24.46.1.101
NAME 'printer-device-id'
Fleming, McDonald Expires 30 October 2015 [Page 36]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
DESC 'The IEEE 1284 Device ID for this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
)
Values of this attribute SHOULD conform to IEEE-ISTO PWG Command Set
Format for IEEE 1284 Device ID [PWG5107.2].
Note: For compatibility with [PWG5100.14] and [PWG5107.2], values of
this attribute SHOULD NOT exceed 1023 octets in length.
4.36. printer-device-service-count
( 1.3.18.0.2.24.46.1.102
NAME 'printer-device-service-count'
DESC 'The number of Printer (Print Service) instances configured on
this Imaging Device (host system).'
EQUALITY integerMatch
ORDERING integerOrderingMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.27
SINGLE-VALUE
)
A positive value indicates the number of Printer (Print Service)
instances configured on this Imaging Device (host system). A value
of '-1' indicates 'unknown'. A value of '0' is not meaningful
(because this attribute must be reported by some Printer instance).
Note: The syntax and values for this attribute are aligned with the
equivalent 'device-service-count' attribute defined in [PWG5100.13].
4.37. printer-uuid
( 1.3.18.0.2.24.46.1.104
NAME 'printer-uuid'
DESC 'A URN specifying UUID of this Printer (Print Service) instance
on this Imaging Device (host system).'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
)
The UUID of this Printer (Print Service) instance on this Imaging
Device (host system). For example:
Fleming, McDonald Expires 30 October 2015 [Page 37]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
'urn:uuid:f81d4fae-7dec-11d0-a765-00a0c91e6bf6'
Values of this attribute MUST conform to the UUID URN namespace
[RFC4122].
Note: For compatibility with [PWG5100.13] and [RFC4122], values of
this attribute SHOULD NOT exceed 45 octets in length.
Note: LDAP application clients SHOULD NOT attempt to use malformed
URN values read from this attribute. LDAP administrative clients
SHOULD not write malformed URN values into this attribute.
Note: The syntax and values for this attribute are aligned with the
equivalent 'printer-uuid' attribute defined in [PWG5100.13].
4.38. printer-charge-info
( 1.3.18.0.2.24.46.1.105
NAME 'printer-charge-info'
DESC 'Descriptive information about paid printing services for this
Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
)
For example:
'This Printer can be used for paid printing at 2 cents/page.'
Note: For compatibility with [PWG5100.13], values of this attribute
SHOULD NOT exceed 1023 octets in length.
Note: For interoperability and consistent text display, values of
this attribute: (a) SHOULD be normalized as recommended in Unicode
Format for Network Interchange [RFC5198]; (b) SHOULD NOT contain any
C0 or C1 control characters except for HT, CR, and LF; and (c) SHOULD
only contain CR and LF characters together (not as singletons).
Note: The syntax and values for this attribute are aligned with the
equivalent 'printer-charge-info' attribute defined in [PWG5100.13].
Fleming, McDonald Expires 30 October 2015 [Page 38]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
4.39. printer-charge-info-uri
( 1.3.18.0.2.24.46.1.106
NAME 'printer-charge-info-uri'
DESC 'A URI for a human-readable Web page for paid printing services
for this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
)
For example:
'http://example.com/charges'
See [STD66] for details of URI syntax.
Note: For compatibility with IPP/1.1 [RFC2911] and [PWG5100.13],
values of this attribute SHOULD NOT exceed 1023 octets in length.
Note: LDAP application clients SHOULD NOT attempt to use malformed
URI values read from this attribute. LDAP administrative clients
SHOULD not write malformed URI values into this attribute.
Note: The syntax and values for this attribute are aligned with the
equivalent 'printer-charge-info-uri' attribute defined in
[PWG5100.13].
4.40. printer-geo-location
( 1.3.18.0.2.24.46.1.107
NAME 'printer-geo-location'
DESC 'A geo: URI specifying the geographic location of this Printer.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
SINGLE-VALUE
)
For example:
'geo:13.4125,103.8667'
Values of this attribute MUST conform to the 'geo' URI scheme
[RFC5870].
Fleming, McDonald Expires 30 October 2015 [Page 39]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
Note: For compatibility with IPP/1.1 [RFC2911] and [PWG5100.13],
values of this attribute SHOULD NOT exceed 1023 octets in length.
Note: LDAP application clients SHOULD NOT attempt to use malformed
URI values read from this attribute. LDAP administrative clients
SHOULD not write malformed URI values into this attribute.
Note: The syntax and values for this attribute are aligned with the
equivalent 'printer-geo-location' attribute defined in [PWG5100.13].
4.41. printer-ipp-features-supported
( 1.3.18.0.2.24.46.1.108
NAME 'printer-ipp-features-supported'
DESC 'List of IPP protocol features that this Printer supports.'
EQUALITY caseIgnoreMatch
SUBSTR caseIgnoreSubstringsMatch
SYNTAX 1.3.6.1.4.1.1466.115.121.1.15
)
Comma-delimited list of IPP protocol features that this Printer
supports. For example:
'none'
'unknown'
'proof-print'
'ipp-everywhere,proof-print,job-save'
Note: Length overflow in values of this attribute MUST be handled by
multiple instances of this attribute, i.e., individual
comma-delimited list members MUST NOT be truncated.
Values of this attribute SHOULD specify only IANA-registered keywords
for the 'ipp-features-supported' attribute defined in [PWG5100.13] or
other standards track IETF or IEEE-ISTO PWG specifications if this
Printer implementation meets all of the IPP feature-specific
conformance requirements.
IANA-registered values include:
'none' (No extension features are supported)
'document-object' (Document object defined in [PWG5100.5])
'job-save' (Job save defined in [PWG5100.11])
'ipp-everywhere' (IPP Everywhere defined in [PWG5100.14])
'page-overrides' (Page overrides defined in [PWG5100.6])
'proof-print' (Proof print defined in [PWG5100.11])
'subscription-object' (Subscription object defined in [RFC3995])
Fleming, McDonald Expires 30 October 2015 [Page 40]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
Note: The value 'unknown' MUST only be reported if the corresponding
IPP Printer attribute is not present, i.e., the value 'unknown' is an
artifact of this LDAP mapping.
Note: The syntax and values for this attribute are aligned with the
equivalent 'printer-ipp-features-supported' attribute defined in
[PWG5100.13].
Fleming, McDonald Expires 30 October 2015 [Page 41]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
5. Definition of Syntaxes
No new attribute syntaxes are defined by this document.
The attribute types defined in Section 4 of this document reference
syntax OIDs defined in Section 3 of [RFC4517], which are summarized
below:
Syntax OID Syntax Description
------------------------------ ------------------
1.3.6.1.4.1.1466.115.121.1.7 Boolean
1.3.6.1.4.1.1466.115.121.1.15 DirectoryString (UTF-8 [STD63])
1.3.6.1.4.1.1466.115.121.1.27 Integer
6. Definition of Matching Rules
No new matching rules are defined by this document.
The attribute types defined in Section 4 of this document reference
matching rules defined in Section 4 of [RFC4517], which are
summarized below:
Matching Rule OID Matching Rule Name Usage
------------------------------ ------------------ -----
2.5.13.13 booleanMatch EQUALITY
2.5.13.2 caseIgnoreMatch EQUALITY
2.5.13.14 integerMatch EQUALITY
2.5.13.15 integerOrderingMatch ORDERING
2.5.13.4 caseIgnoreSubstringsMatch SUBSTR
Fleming, McDonald Expires 30 October 2015 [Page 42]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
7. IANA Considerations
This document does not define any new syntaxes or matching rules.
This document defines a few new attribute types that should be
registered by IANA when this document is published (see section 7.1
below).
All of the object classes and most of the attribute types described
in this document were registered by IANA when RFC 3712 was published
(see section 7.2 below).
7.1. Registration of Attribute Types
The following Attribute Type OIDs have been assigned by IEEE-IST0 PWG
(see section 1.3.2) and should be registered by IANA when this
document is published.
Subject: Request for Object Identifier Descriptor Registration
Descriptor (short name): see table below
Object Identifier: see table below
Person & email address to contact for further information: see below
Usage: attribute type
Specification: RFCnnnn [ [RFC Editor: to be assigned] ]
Author/Change Controller:
Ira McDonald
High North Inc
221 Ridge Ave
Grand Marais, MI 49839
USA
Phone: +1 906-494-2434
Email: blueroofmusic@gmail.com
Comments:
Attribute Type OID
------------------------------------ -----------------------
printer-device-id 1.3.18.0.2.24.46.1.101
printer-device-service-count 1.3.18.0.2.24.46.1.102
printer-uuid 1.3.18.0.2.24.46.1.104
Fleming, McDonald Expires 30 October 2015 [Page 43]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
printer-charge-info 1.3.18.0.2.24.46.1.105
printer-charge-info-uri 1.3.18.0.2.24.46.1.106
printer-geo-location 1.3.18.0.2.24.46.1.107
printer-ipp-features-supported 1.3.18.0.2.24.46.1.108
7.2. Object Classes and Attribute Types from RFC 3712
This section is strictly informative. None of the LDAP OIDs listed
in this section should be re-registered by IANA when this document is
published.
The following Object Class OIDs were assigned by IBM (see section
1.3.1) and were already registered by IANA when RFC 3712 was
published.
Object Class OID
------------------------------------ -----------------------
slpServicePrinter 1.3.18.0.2.6.254
printerAbstract 1.3.18.0.2.6.258
printerService 1.3.18.0.2.6.255
printerServiceAuxClass 1.3.18.0.2.6.257
printerIPP 1.3.18.0.2.6.256
printerLPR 1.3.18.0.2.6.253
The following Attribute Type OIDs were assigned by IBM (see section
1.3.1) and were already registered by IANA when RFC 3712 was
published.
Attribute Type OID
------------------------------------ -----------------------
printer-uri 1.3.18.0.2.4.1140
printer-xri-supported 1.3.18.0.2.4.1107
printer-name 1.3.18.0.2.4.1135
printer-natural-language-configured 1.3.18.0.2.4.1119
printer-location 1.3.18.0.2.4.1136
printer-info 1.3.18.0.2.4.1139
printer-more-info 1.3.18.0.2.4.1134
printer-make-and-model 1.3.18.0.2.4.1138
printer-ipp-versions-supported 1.3.18.0.2.4.1133
printer-multiple-document-jobs-supported 1.3.18.0.2.4.1132
printer-charset-configured 1.3.18.0.2.4.1109
printer-charset-supported 1.3.18.0.2.4.1131
printer-generated-natural-language-supported 1.3.18.0.2.4.1137
printer-document-format-supported 1.3.18.0.2.4.1130
printer-color-supported 1.3.18.0.2.4.1129
printer-compression-supported 1.3.18.0.2.4.1128
printer-pages-per-minute 1.3.18.0.2.4.1127
printer-pages-per-minute-color 1.3.18.0.2.4.1126
printer-finishings-supported 1.3.18.0.2.4.1125
Fleming, McDonald Expires 30 October 2015 [Page 44]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
printer-number-up-supported 1.3.18.0.2.4.1124
printer-sides-supported 1.3.18.0.2.4.1123
printer-media-supported 1.3.18.0.2.4.1122
printer-media-local-supported 1.3.18.0.2.4.1117
printer-resolution-supported 1.3.18.0.2.4.1121
printer-print-quality-supported 1.3.18.0.2.4.1120
printer-job-priority-supported 1.3.18.0.2.4.1110
printer-copies-supported 1.3.18.0.2.4.1118
printer-job-k-octets-supported 1.3.18.0.2.4.1111
printer-current-operator 1.3.18.0.2.4.1112
printer-service-person 1.3.18.0.2.4.1113
printer-delivery-orientation-supported 1.3.18.0.2.4.1114
printer-stacking-order-supported 1.3.18.0.2.4.1115
printer-output-features-supported 1.3.18.0.2.4.1116
printer-aliases 1.3.18.0.2.4.1108
Fleming, McDonald Expires 30 October 2015 [Page 45]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
8. Internationalization Considerations
All text string attributes defined in this document of syntax
'DirectoryString' [RFC4517] have values that are encoded in UTF-8
[STD63], as required by [RFC4517].
A language tag [BCP47] for all of the text string attributes defined
in this document is contained in the
printer-natural-language-configured attribute.
Therefore, all object classes defined in this document conform to the
IETF Policy on Character Sets and Languages [BCP18].
Note: For interoperability and consistent text display, values of
attributes defined in this document: (a) SHOULD be normalized as
recommended in Unicode Format for Network Interchange [RFC5198]; (b)
SHOULD NOT contain DEL or any C0 or C1 control characters except for
HT, CR, and LF; (c) SHOULD only contain CR and LF characters together
(not as singletons); and SHOULD NOT contain HT, CR, or LF characters
in names, e.g., printer-name and printer-aliases.
9. Security Considerations
See [RFC4513] for detailed guidance on authentication methods for
LDAP and the use of TLS/1.2 [RFC5246] to supply connection
confidentiality and data integrity for LDAP sessions.
As with any LDAP schema, it is important to protect specific entries
and attributes with the appropriate access control. It is
particularly important that only administrators can modify entries
defined in this LDAP Printer schema. Otherwise, an LDAP client might
be fooled into diverting print service requests from the original
Printer (or spooler) to a malicious intruder's host system, thus
exposing the information in printed documents.
Note: Security vulnerabilities can arise if DEL or any C0 or C1
control characters are included in names, e.g., printer-name or
printer-aliases.
For additional security considerations of deploying Printers in an
IPP environment, see Section 8 of [RFC2911].
Fleming, McDonald Expires 30 October 2015 [Page 46]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
10. References
10.1. Normative References
[BCP47] A. Phillips, Ed., M. Davis, Ed. Tags for Identifying
Languages, BCP 47, RFC 5646, September 2009.
[IANACHAR] Internet Assigned Numbers Authority (IANA) Registry
"Character Sets"
<http://www.iana.org/assignments/character-sets>
[IANAIPP] Internet Assigned Numbers Authority (IANA) Registry
"Internet Printing Protocol"
<http://www.iana.org/assignments/ipp-registrations>
[IANAMIME] Internet Assigned Numbers Authority (IANA) Registry "MIME
Media Types"
<http://www.iana.org/assignments/media-types/index.html>
[IPPSURI] McDonald, I., and M. Sweet. IPP over HTTPS Transport
Binding and 'ipps' URI Scheme, draft-mcdonald-ipps-uri-scheme-xx.txt,
work-in-progress.
[PWG5100.5] Carney, D., Hastings, T., and P. Zehler. Internet
Printing Protocol (IPP): Document Object, PWG 5100.5, October 2003.
<ftp://ftp.pwg.org/pub/pwg/candidates/
cs-ippdocobject10-20031031-5100.5.pdf>
[PWG5100.6] Zehler, P., Herriot, R., and K. Ocke. Internet Printing
Protocol (IPP): Page Overrides, October 2003.
<ftp://ftp.pwg.org/pub/pwg/candidates/
cs-ipppageoverride10-20031031-5100.6.pdf>
[PWG5100.12] Bergman, R., McDonald, I., and M. Sweet. Internet
Printing Protocol Version 2.0 Second Edition (IPP/2.0 SE), PWG
5100.12, February 2011.
<ftp://ftp.pwg.org/pub/pwg/candidates/
cs-ipp20-20110214-5100.12.pdf>
[PWG5100.13] Sweet, M., and I. McDonald. IEEE-ISTO PWG IPP Job and
Printer Extensions - Set 3, PWG 5100.13, July 2012.
<ftp://ftp.pwg.org/pub/pwg/candidates/
cs-ippjobprinterext3v10-20120727-5100.13.pdf>
[PWG5100.14] Sweet, M., and I. McDonald. IEEE-ISTO PWG IPP
Everywhere, January 2013.
Fleming, McDonald Expires 30 October 2015 [Page 47]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
<ftp://ftp.pwg.org/pub/pwg/candidates/
cs-ippeve10-20130128-5100.14.pdf>
[PWG5101.1] Bergman, R., Hastings, T., and M. Sweet. IEEE-ISTO PWG
Media Standardized Names 2.0, PWG 5101.1, March 2013.
<ftp://ftp.pwg.org/pub/pwg/candidates/
cs-pwgmsn20-20130328-5101.1.pdf>
[PWG5107.2] I. McDonald. IEEE-ISTO PWG Command Set for IEEE 1284
Device ID, PWG 5107.2, May 2010.
<ftp://ftp.pwg.org/pub/pwg/candidates/
cs-pmp1284cmdset10-20100531-5107.2.pdf>
[RFC2119] S. Bradner. Key words for use in RFCs to Indicate
Requirement Levels, RFC 2119 / BCP 14, March 1997.
[RFC2617] Franks, J., Hallam-Baker, P., Hostetler, J., Lawrence, S.,
Leach, P., Luotonen, A., and L. Stewart. HTTP Authentication: Basic
and Digest Access Authentication, RFC 2617, June 1999.
[RFC2911] T. Hastings, Ed., Herriot, R., Isaacson, S., and P. Powell.
Internet Printing Protocol/1.1: Model and Semantics, RFC 2911,
September 2000.
[RFC2926] Kempf, J., Moats, R., and P. St. Pierre. Conversion of
LDAP Schemas to and from SLP Templates, RFC 2926, September 2000.
[RFC3510] Herriot, R., and I. McDonald. Internet Printing Protocol
1.1: IPP URL Scheme, RFC 3510, April 2003.
[RFC3987] Duerst, M., and M. Suignard. Internationalized Resource
Identifiers (IRI), RFC 3987, January 2005.
[RFC3995] Herriot, R., and T. Hastings. Internet Printing Protocol
(IPP): Event Notifications and Subscriptions, RFC 3995, March 2005.
[RFC4122] Leach, P., Mealling, M., and R. Salz. A Universally Unique
IDentifier (UUID) URN Namespace, RFC 4122, July 2005.
[RFC4510] K. Zeilenga, Ed. Lightweight Directory Access Protocol
(LDAP): Technical Specification Road Map, RFC 4510, June 2006.
[RFC4513] R. Harrison, Ed. Lightweight Directory Access Protocol
(LDAP): Authentication Methods and Security Mechanisms, RFC 4513,
June 2006.
[RFC4517] S. Legg, Ed. Lightweight Directory Access Protocol (LDAP):
Syntaxes and Matching Rules, RFC 4517, June 2006.
[RFC4519] A. Sciberras, Ed. Lightweight Directory Access Protocol
(LDAP): Schema for User Applications, RFC 4519, June 2006.
Fleming, McDonald Expires 30 October 2015 [Page 48]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
[RFC4524] K. Zeilenga, Ed. COSINE LDAP/X.500 Schema, RFC 4524, June
2006.
[RFC5198] Klensin, J., and M. Padlipsky. Unicode Format for Network
Interchange, RFC 5198, March 2008.
[RFC5246] Dierks, T., and E. Rescorla. The Transport Layer Security
(TLS) Protocol Version 1.2, RFC 5246, August 2008.
[RFC5280] Cooper, D., Santesson, S., Farrell, S., Boeyen, S.,
Housley, R., and W. Polk. Internet X.509 Public Key Infrastructure
Certificate and Certificate Revocation List (CRL) Profile, RFC 5280,
May 2008.
[RFC5870] Mayrhofer, A., and C. Spanring. A Uniform Resource
Identifier for Geographic Locations ('geo' URI), RFC 5870, June 2010.
[RFC6818] P. Yee. Updates to the Internet X.509 Public Key
Infrastructure Certificate and Certificate Revocation List (CRL)
Profile, RFC 6818, January 2013.
[RFC7235] Fielding, R., and J. Reschke. Hypertext Transfer Protocol
(HTTP/1.1): Authentication, RFC 7235, June 2014.
[STD63] F. Yergeau. UTF-8, a Transformation Format of ISO 10646, STD
63, RFC 3629, November 2003.
[STD66] Berners-Lee, T., Fielding, R., and L. Masinter. Uniform
Resource Identifier (URI): Generic Syntax, STD 66, RFC 3986, January
2005.
10.2. Informative References
[BCP13] Freed, N., Klensin, J., and T. Hansen. Media Type
Specifications and Registration Procedures, BCP 13, RFC 6838, January
2013.
[BCP18] H. Alvestrand. IETF Policy on Character Sets and Languages,
BCP 18, RFC 2277, January 1998.
[BCP19] Freed, N., and J. Postel. IANA Charset Registration
Procedures, BCP 19, RFC 2978, October 2000.
[BCP35] Hansen, T., Hardie, T., and L. Masinter. Guidelines and
Registration Procedures for New URI Schemes, BCP 35, RFC 4395,
February 2006.
Fleming, McDonald Expires 30 October 2015 [Page 49]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
[IANASLP] Internet Assigned Numbers Authority (IANA) Registry
"Service Location Protocol, Version 2 (SLPv2) Templates"
<http://www.iana.org/assignments/svrloc-templates.html>
[PWG] IEEE-ISTO Printer Working Group (PWG)
<http://www.pwg.org>
[PWGIPP] IEEE-ISTO PWG Internet Printing Protocol Working Group
<http://www.pwg.org/ipp>
[RFC1179] L. McLaughlin. Line Printer Daemon Protocol, RFC 1179,
August 1990.
[RFC1951] P. Deutsch. DEFLATE Compressed Data Format Specification
Version 1.3, RFC 1951, May 1996.
[RFC1952] P. Deutsch. GZIP File Format Specification Version 4.3,
RFC 1952, May 1996.
[RFC1977] V. Schryver. PPP BSD Compression Protocol, RFC 1977,
August 1996.
[RFC2079] M. Smith. Definition of an X.500 Attribute Type and an
Object Class to Hold Uniform Resource Identifiers (URIs), RFC 2079,
January 1997.
[RFC2566] deBry, R., Hastings, T., Herriot, R., Isaacson, S., and
P. Powell. Internet Printing Protocol/1.0: Model and Semantics, RFC
2566, April 1999.
[RFC2608] Guttman, E., Perkins, C., Veizades, J., and M. Day.
Service Location Protocol v2, RFC 2608, June 1999.
[RFC2609] Guttman, E., Perkins, C., and J. Kempf. Service Templates
and Service: Schemes, RFC 2609, June 1999.
[RFC3712] Fleming, P., and I. McDonald. Lightweight Directory Access
Protocol (LDAP): Schema for Printer Services, RFC 3712, February
2004.
[RFC4559] Jaganathan, K., Zhu, L., and J. Brezak. SPNEGO-based
Kerberos and NTLM HTTP Authentication in Microsoft Windows, RFC 4559,
June 2006.
[SLPPRT20] St. Pierre, P., Isaacson, S., and I. McDonald. Definition
of of the PrinterAbstract Service Type v2.0, May 2000.
Reviewed and approved by IETF SLP Designated Expert, according to
Section 5 'IANA Considerations' in [RFC2609].
Archived in [IANASLP] as "printer.2.0.en".
Fleming, McDonald Expires 30 October 2015 [Page 50]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
11. Appendix A - Changes since RFC 3712
1) Added many editorial corrections and clarifications
- corrected typos, missing words, and ambiguous sentences;
- replaced lowercase 'printer' with titlecase 'Printer' for
readability and consistency with IETF and IEEE-ISTO PWG IPP
standards usage;
- added implementation notes;
- updated and added references.
2) Deleted length restrictions from formal definitions of
DirectoryString syntax attributes
- replaced with notes recommending length restrictions for
compatibility with existing implementations of [RFC3712] and
underlying string length limits in [RFC2707], [RFC2911],
[RFC3805], [PWG5107.2], [PWG5100.13], and [PWG5100.14].
3) Added new Printer attributes defined in [PWG5107.2],
[PWG5100.13], and [PWG5100.14] (see section 7.1)
- see the table of Printer attributes and source documents in
section 4 'Definition of Attribute Types' in this document;
- added support for IEEE-ISTO PWG IPP Everywhere [PWG5100.14]
project.
4) Added implementation note to section 4 about string encodings
- added discussion of 'List of xxx' and 'One of xxx' encodings;
- stated that any of these attributes can be represented as
multiple instances (i.e., to avoid length overflow).
5) Improved comma-delimited examples of string attributes
- added both single-valued and multi-valued examples.
6) Clarified use of printer-xri-supported and
printer-resolution-supported attributes and field delimiters
- added note in section 4 Definition of Attribute Types to
explain the origin of the different field delimiters;
- added examples to show optional *trailing* whitespace after '<'
delimiters in printer-xri-supported;
- added examples to show optional *trailing* whitespace after '>'
delimiters in printer-resolution-supported.
7) Clarified section 8 'Internationalization Considerations'
- added note about Network Unicode [RFC5198] and avoiding use of
C0 and C1 control characters.
8) Clarified section 9 'Security Considerations'
- added note about security vulnerabilities caused by use of DEL
or any C0 or C1 control characters in names.
Fleming, McDonald Expires 30 October 2015 [Page 51]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
9) Clarified terms and abbreviations
- renamed section 2 Conventions Used in This Document;
- added section 2.1 Requirements Language;
- added section 2.2 LDAP Schema Descriptions;
- added section 2.3 Abbreviations.
12. Appendix X - Change History
[ [RFC Editor: This section to be deleted before RFC publication] ]
30 April 2015 - draft-mcdonald-ldap-printer-schema-13.txt
Editorial - revised section 7.2 Object Classes and Attribute Types
from RFC 3712 to clarify that the section is Informative and that
IANA does NOT need to change registration of any of these existing
LDAP OIDs, per advice advice of Amanda Baber on 30 April 2015 during
IANA final review.
19 April 2015 - draft-mcdonald-ldap-printer-schema-12.txt
Editorial - revised section 7.1 Registration of Attribute Types to
correct title of registration form, per advice of Rolf Sonneveld on
16 April 2015 during IANA review by LDAP Designated Experts.
23 March 2015 - draft-mcdonald-ldap-printer-schema-11.txt
Editorial - revised section 2 Conventions Used in This Document to
contain section 2.1 Requirements Language, section 2.2 LDAP Schema
Descriptions, and section 2.3 Abbreviations (moved from former
Appendix B), per final version of RFC 7472.
Editorial - revised section 7 IANA Considerations and subsections to
clarify extent of new IANA registration requests, per Pearl Liang.
Editorial - revised Appendix A - Changes since RFC 3712, to capture
changes in section 2 and section 7.
Editorial - moved Acknowledgements section after all Appendices and
before Authors' Addresses, per final version of RFC 7472.
29 January 2015 - draft-mcdonald-ldap-printer-schema-10.txt
Editorial - Updated copyright year to 2015.
Editorial - revised sections 4.1 printer-uri, 4.2
printer-xri-supported, 4.7 printer-more-info, and 4.39
printer-charge-info-uri to simply refer to [STD66] for details of URI
syntax (and be silent about conflicting RFC 6874 for IPv6 addresses)
per advice of Alexey Melnikov on 16 December 2014 and clarifications
from Mike Sweet on 29 January 2015.
Editorial - revised section 4.2 printer-xri-supported to clarify that
the 'certificate' value refers to the IPP Client certificate
extracted from the TLS session, per advice of Alexey Melnikov on 16
December 2014.
Editorial - revised section 4.3 printer-name to change "MAY" to "can"
throughout the second Note paragraph, per advice of Alexey Melnikov
Fleming, McDonald Expires 30 October 2015 [Page 52]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
on 16 December 2014.
Editorial - revised section 4.13
printer-generated-natural-language-supported to change example of
from "fr-fr" to "fr-ca" (French as spoken in Canada) as a better
illustration, per advice of Alexey Melnikov on 16 December 2014.
Editorial - revised section 7 IANA Considerations to make clear which
OIDs were already previously assigned by IBM and IANA-registered by
RFC 3712, per advice of Nevil Brownlee on 18 December 2014.
Editorial - revised section 12 Appendix A - Changes since RFC 3712 to
delete erroneous change from Informational to Standards-Track.
28 September 2014 - draft-mcdonald-ldap-printer-schema-09.txt
Editorial - Changed "Intended Status" as "Informational", per advice
of Barry Leiba on 18 August 2014.
Editorial - Revised Abstract, Boilerplate, and Introduction to state
that this document is an Independent Submission to the RFC Editor
Stream, per advice of Barry Leiba on 18 August 2014.
3 July 2014 - draft-mcdonald-ldap-printer-schema-08.txt
Working draft - for IEEE-ISTO PWG IPP Everywhere project
Editorial - revised sections 4.2 and 10.1 to add [RFC7235] normative
reference, update for [RFC2617], per PWG IPP WG review.
Editorial - revised sections 4.2 and 10.1 to add [RFC6818] normative
reference, update for [RFC5280], per PWG IPP WG review.
Editorial - revised section 10.1 to update [PWG5101.1] normative
reference to v2.0 (March 2013), per PWG IPP WG review.
13 March 2014 - draft-mcdonald-ldap-printer-schema-07.txt
Working draft - for IEEE-ISTO PWG IPP Everywhere project
Global - updated publication and expiration dates in copyright,
header, footer, and boilerplate.
Editorial - revised sections 4, 4.2, and 4.24 to add implementation
notes about different field delimiters in printer-xri-supported and
printer-resolution-supported (for compatibility with SLP template),
per PWG IPP WG.
Editorial - revised appendix A 'Changes since RFC 3712' to correct
typos and expand PWG IPP Everywhere reference, per PWG IPP WG.
3 March 2014 - draft-mcdonald-ldap-printer-schema-06.txt
Working draft - for IEEE-ISTO PWG IPP Everywhere project
Global - updated publication and expiration dates in copyright,
header, footer, and boilerplate.
Global - replaced 'SHOULD not' w/ 'SHOULD NOT' for RFC 2911
compliance, per Alexey Melnikov.
Editorial - revised Abstract and section 1 Introduction to clarify
that this document is an individual submission to the IETF by the IPP
WG of the IEEE-ISTO PWG, per Tom Petch and IPP WG review.
Editorial - revised Abstract and section 1 Introduction to clarify
that this document obsoletes [RFC3712], per Alexey Melnikov.
Editorial - added section 1.1 'Relationship to SLP Printer Service'
and section 1.2 'Source of LDAP Printer Attributes' for clarity.
Fleming, McDonald Expires 30 October 2015 [Page 53]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
Editorial - added section 1.3 'Sources of LDAP Printer Schema OIDs'
to describe permanent delegation of "1.3.18.0.2.24.46" to the
IEEE-ISTO PWG by IBM in October 2011, per Alexey Melnikov.
Editorial - added section 1.4 'Rationale for Design Choices' for
clarity.
Editorial - revised sections 3.1, 3.4, 3.5, and 3.6 to delete
erroneous SHOULD references to structural classes, per Alexey
Melnikov.
Editorial - revised section 4 to clarify reference to section 4 of
[RFC4517] and forward reference to section 6 of LDAP Printer Schema,
per Alexey Melnikov.
Editorial - revised section 4 to add implementation note about
compatibility with existing implementations of [RFC3712] and
underlying string length limits in [RFC2707], [RFC2911], [RFC3805],
[PWG5107.2], [PWG5100.13], and [PWG5100.14], per Alexey Melnikov.
Editorial - revised section 4.4 to change SHOULD to MUST for
conformance to [BCP47] for natural language tags, per Alexey
Melnikov.
Editorial - revised section 4.4 printer-natural-language-configured
and section 4.13 printer-generated-natural-language-supported
definitions to clarify that they refer to LDAP Printer in syntax
DirectoryString (UTF-8), per Alexey Melnikov.
Editorial - revised section 4.11 printer-charset-configured and
section 4.12 printer-charset-supported definitions to clarify that
they refer to IPP protocol values and that corresponding LDAP Printer
attributes are always in syntax DirectoryString (UTF-8), per Alexey
Melnikov.
Editorial - revised section 4.20 printer-number-up-supported and
section 4.35 printer-device-id definitions to add missing
SINGLE-VALUE clause, per Alexey Melnikov.
Editorial - revised section 4.35 printer-device-id to delete
confusing and redundant note about ordering of key/value pairs within
LDAP attribute values (since this is clearly explained in
[PWG5107.2]), per Alexey Melnikov.
Editorial - revised section 4 syntaxes of printer-uri,
printer-xri-supported, printer-name,
printer-natural-language-configured, printer-location, printer-info,
printer-more-info, printer-make-and-model,
printer-ipp-versions-supported, printer-charset-configured,
printer-charset-supported,
printer-generated-natural-language-supported,
printer-document-format-supported, printer-compression-supported,
printer-finishings-supported, printer-sides-supported,
printer-media-supported, printer-media-local-supported,
printer-resolution-supported, printer-current-operator,
printer-service-person, printer-delivery-orientation-supported,
printer-stacking-order-supported, printer-output-features-supported,
printer-aliases, printer-device-id, printer-uuid,
printer-charge-info, printer-charge-info-uri, printer-geo-location,
printer-ipp-features-supported, to remove length restrictions in
syntax and add textual notes instead about IPP compatibility (where
Fleming, McDonald Expires 30 October 2015 [Page 54]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
applicable), per Alexey Melnikov.
Editorial - added appendix A 'Changes since RFC 3712', per Alexey
Melnikov.
Editorial - added missing informative reference to [RFC3712].
19 September 2013 - draft-mcdonald-ldap-printer-schema-05.txt
Working draft - for IEEE-ISTO PWG IPP Everywhere project
Global - updated publication and expiration dates in copyright,
header, footer, and boilerplate.
Global - updated references, per IEEE-ISTO PWG IPP WG review.
17 May 2013 - draft-mcdonald-ldap-printer-schema-04.txt
Working draft - for IEEE-ISTO PWG IPP Everywhere project
Global - updated publication and expiration dates in copyright,
header, footer, and boilerplate.
Global - added references to IPP Everywhere, per IEEE-ISTO PWG IPP WG
review.
Editorial - revised section 4.41 printer-ipp-features-supported to
show 'ipp-everywhere' defined in PWG 5100.14, per IEEE-ISTO PWG IPP
WG review.
18 November 2012 - draft-mcdonald-ldap-printer-schema-03.txt
Working draft - for IEEE-ISTO PWG IPP Everywhere project
Global - updated publication and expiration dates in copyright,
header, footer, and boilerplate.
Global - updated contact info for Pat Fleming.
Global - updated various references.
Global - added references to IEEE-ISTO PWG and IEEE-ISTO PWG IPP WG,
per IEEE-ISTO PWG IPP WG review.
Global - deleted all references to PWG IPP Everywhere and values
defined in that specification, per IEEE-ISTO PWG IPP WG review.
Global - deleted 'printer-device-uuid' attribute, per IEEE-ISTO PWG
IPP WG review.
Global - revised all 'One of' attributes to add implementation note
that multiple values are represented as multiple instances, per
IEEE-ISTO PWG IPP WG review.
Global - revised all 'List of' attributes to add implementation note
that length overflow is handled by multiple instances, per IEEE-ISTO
PWG IPP WG review.
Global - revised many DESC clauses to correct truncation due to
no-fill formatting, per IEEE-ISTO PWG IPP WG review.
Editorial - revised section 4 Definition of Attribute Types to add
implementation note recommending use of Network Unicode [RFC5198],
recommending against the use of DEL or any C0 or C1 control
characters (except HT, CR, and LF), and recommending against HT, CR,
and LF in names (e.g., printer-name or printer-aliases), per
IEEE-ISTO PWG IPP WG review.
Editorial - revised section 4 Definition of Attribute Types to add
implementation note contrasting 'List of xxx' and 'One of xxx' and
stating that any of these attributes can be represented as multiple
Fleming, McDonald Expires 30 October 2015 [Page 55]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
instances (i.e., to avoid length overflow), per IEEE-ISTO PWG IPP WG
review.
Global - revised all comma-delimited examples to include both single-
and multi-valued examples, per IEEE-ISTO PWG IPP WG review.
Editorial - revised section 4.2 printer-xri-supported text and
examples to show optional *trailing* whitespace after '<' delimiters,
per IEEE-ISTO PWG IPP WG review.
Editorial - revised section 4.3 printer-name to break recommendations
into separate implementation notes, per IEEE-ISTO PWG IPP WG review.
Editorial - revised section 4.20 printer-number-up-supported to add
note explaining that this differs from the corresponding IPP
attribute and is mapped from the largest reported value in IPP, per
IEEE-ISTO PWG IPP WG review.
Editorial - revised section 4.22 printer-media-supported to separate
examples of media sizes, types, and colors, per IEEE-ISTO PWG IPP WG
review.
Editorial - revised section 4.24 printer-resolution-supported text
and examples to show optional *trailing* whitespace after '>'
delimiters, per IEEE-ISTO PWG IPP WG review.
Editorial - revised section 4.34 printer-aliases to add Network
Unicode note like printer-name, per IEEE-ISTO PWG IPP WG review.
Editorial - revised section 4.35 printer-device-id to explicitly list
the required key/value pairs as in PWG IPP Everywhere, per IEEE-ISTO
PWG IPP WG review.
Editorial - revised section 4.37 printer-uuid to add example of a
valid UUID per [RFC4122], per IEEE-ISTO PWG IPP WG review.
Editorial - revised section 4.36 printer-device-service-count to add
example, per IEEE-ISTO PWG IPP WG review.
Editorial - revised section 4.39 printer-charge-info-uri to add
example, per IEEE-ISTO PWG IPP WG review.
Editorial - revised section 4.40 printer-geo-location to add example
of a value 'geo:' URI per [RFC5870], per IEEE-ISTO PWG IPP WG review.
Editorial - revised section 4.41 printer-ipp-features-supported to
delete 'ipp-everywhere' and add 'unknown' (with explanation), per
IEEE-ISTO PWG IPP WG review.
Editorial - revised section 7 IANA Considerations to correct
truncation of some OIDs, per IEEE-ISTO PWG IPP WG review.
Editorial - revised section 7.2 Registration of Attribute Types to
delete issue for OID assignments, per IEEE-ISTO PWG IPP WG review.
Editorial - revised section 8 Internationalization Considerations to
add detailed note about Network Unicode [RFC5198] and avoiding use of
C0 and C1 control characters, per IEEE-ISTO PWG IPP WG review.
Editorial - revised section 9 Security Considerations to add note
about security vulnerabilities caused by use of DEL or any C0 or C1
control characters in names, per IEEE-ISTO PWG IPP WG review.
Editorial - added appendix B Abbreviations, per IEEE-ISTO PWG IPP WG
review.
20 May 2012 - draft-mcdonald-ldap-printer-schema-02.txt
Working draft - for IEEE-ISTO PWG IPP Everywhere project
Fleming, McDonald Expires 30 October 2015 [Page 56]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
Cover - changed intended category to Standards Track for consistency
w/ recent LDAP schema specs and IPP Everywhere recommendations.
Global - replace 'must' w/ 'MUST', 'should' w/ 'SHOULD', and 'may' w/
'can' or 'MAY' (as appropriate) for Standards Track document.
Global - updated publication and expiration dates in copyright,
header, footer, and boilerplate.
Global - replaced [RFC1759] references (obsolete) w/ [RFC3805], per
IEEE-ISTO PWG IPP WG review.
Global - replaced lowercase 'printer' with titlecase 'Printer' for
readability and consistency with IPP standards usage.
Revised section 1, to correct format of reference to IPP JPS3, per
IEEE-ISTO PWG IPP WG review.
Revised section 3.5, section 4.1, and section 4.2 to add references
to IPP and IPPS URI scheme specs, per IEEE-ISTO PWG IPP WG review.
Revised section 4.2 to correct reference for 'digest' and add
reference for 'certificate' to [RFC5280], per IEEE-ISTO PWG IPP WG
review.
Revised sections 4.5, 4.6, 4.8, 4.29, 4.30, and 4.36 to add note
about use of Network Unicode [RFC5198] and prohibition against all C0
and C1 control characters except HT, CR, and LF, per IEEE-ISTO PWG
IPP WG review.
Revised section 4.9 to enumerate all known IPP versions (noting that
IPP/1.0 is OBSOLETE) and refer to IANA IPP Registry, per IEEE-ISTO
PWG IPP WG review.
Revised section 4.22 to replace legacy examples w/ examples of media
size names, media types, and media colors defined in [PWG5101.1], per
IEEE-ISTO PWG IPP WG review.
Revised section 4.24 to delete obscure note about delimiter, per
IEEE-ISTO PWG IPP WG review.
Revised sections 4.25, 4.31, 4.32, and 4.33 to add note about use of
'unknown' (out-of-band value) ONLY when the correspond IPP or Printer
MIB attributes are not present (i.e., artifact of LDAP mapping), per
IEEE-ISTO PWG IPP WG review.
Revised section 4.39 to add exhaustive list of feature keywords from
[PWG5100.JPS3] and [PWG5100.EVE], per IEEE-ISTO PWG IPP WG review.
Added section 4.x 'printer-device-service-count' aligned w/
"device-service-count" in [PWG5100.JPS3], per IEEE-ISTO PWG IPP WG
review.
Added section 4.x 'printer-device-uuid' aligned w/ "device-uuid" in
[PWG5100.JPS3], per IEEE-ISTO PWG IPP WG review.
Revised sections 4.x to add length restrictions to unbounded strings
(text, URI, and UUID) w/ maximum 255 octets (consistent w/ RFC 3712),
verify attribute lengths (per source IPP attribute), and clarify
"list of" (comma-delimited) versus "one of" (simple multi-valued) for
all 'printer-xxx-supported' attributes, per IEEE-ISTO PWG IPP WG
review.
Revised section 7.2 to assign new OIDs for the LDAP Printer Schema
new attributes, per IEEE-ISTO PWG IPP WG review.
Revised section 10.1 to add BCP 14 to [RFC2119] definition, per
IEEE-ISTO PWG IPP WG review.
Fleming, McDonald Expires 30 October 2015 [Page 57]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
Revised section 10.1 and section 10.2 to move [RFC2617], [RFC3987],
[RFC4122], [RFC5198], [RFC5246], [RFC5280], [RFC5870], [STD63] from
informative to normative references, per IEEE-ISTO PWG IPP WG review.
3 April 2012 - draft-mcdonald-ldap-printer-schema-01.txt
Working draft - for IEEE-ISTO PWG IPP Everywhere project
Global - changed [IPPEVE1] to [PWG5100.EVE] and [IPPJPS3] to
[PWG5100.JPS3], per IEEE-ISTO PWG IPP WG review.
Revised section 1.1, to add printer-charge-info-uri and printer-uuid
to discussion of URI syntax, per IEEE-ISTO PWG IPP WG review.
Revised section 1.2 and section 1.3, to add printer-device-id to
discussions of equality and substring matching, per IEEE-ISTO PWG IPP
WG review.
Revised section 3.2, section 4, and section 7.2, to delete redundant
printer-organization and printer-organizational-unit (already covered
by 'O' and 'OU'), per IEEE-ISTO PWG IPP WG review.
Revised section 3.2, section 4, and section 7.2, to add missing
printer-charge-info, per IEEE-ISTO PWG IPP WG review.
Revised section 3.5, section 4, and section 7.2, to rename
printer-ipp-extensions-supported to printer-ipp-features-supported,
per IEEE-ISTO PWG IPP WG review.
Revised numerous section 4 subsections, to add references to
[IANAIPP] or [RFC3805] as appropriate for enumerations and keywords,
per IEEE-ISTO PWG IPP WG review.
Revised section 4.2, to add 'negotiate' as value for 'auth' and
references to [PWG5100.JPS3], [RFC4559], and [IANAIPP], per IEEE-ISTO
PWG IPP WG review.
Revised section 4.2, to use 'example.com' for all DNS names, per
IEEE-ISTO PWG IPP WG review.
Revised section 4.22 and section 4.23, to add normative reference to
PWG Media Standardized Names [PWG5101.1], per IEEE-ISTO PWG IPP WG
review.
Revised section 4.24, to divide notes into two separate paragraphs,
per IEEE-ISTO PWG IPP WG review.
Revised section 4.31, section 4.32, and section 4.33, to change
'Values ... include' to 'Values ... are' (i.e., closed set), per
IEEE-ISTO PWG IPP WG review.
Revised section 4.35 printer-device-id, to add warning about ordering
of required key/value pairs (first) and truncation only at key/value
pair boundaries for interoperability, per IEEE-ISTO PWG IPP WG
review.
Revised section 4, to add printer-charge-info from [PWG5100.JPS3],
per IEEE-ISTO PWG IPP WG review.
Revised section 4.38 printer-geo-location, to change 'should' to
'must' for conformance to [RFC5870], per IEEE-ISTO PWG IPP WG review.
Revised section 4.39, to change printer-ipp-extensions-supported to
printer-ipp-features-supported per [PWG5100.JPS3] and add examples,
per IEEE-ISTO PWG IPP WG review.
Revised section 4 subsection printer-uuid, to change 'should' to
'must' for conformance to [RFC4122], per IEEE-ISTO PWG IPP WG review.
Fleming, McDonald Expires 30 October 2015 [Page 58]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
Revised section 10 References, to update out-of-date references.
2 October 2011 - draft-mcdonald-ldap-printer-schema-00.txt
Working draft - for IEEE-ISTO PWG IPP Everywhere project
Revised document to add current I-D individual submission
boilerplate.
Revised Abstract and section 1 Introduction, to cite [PWG5107.2] and
[PWG5100.JPS3] new attribute sources.
Revised section 3.2 printerAbstract, to add new attributes from
[PWG5107.2] and [IPPJPS3].
Revised section 3.5, to add new attributes from [IPPJPS3].
Revised section 4 Definition of Attribute Types, to add new
attributes from [PWG5107.2] and [IPPJPS3] to table and later specific
definitions.
Revised section 7.2 Registration of Attribute Types, to add new
attributes from [PWG5107.2] and [IPPJPS3] - new OIDs needed.
Revised section 10 References, to update out-of-date references.
13. Acknowledgments
The editors wish to acknowledge significant contributions from Ken
Jones and Harry Lewis and excellent comments from Patrik Faltstrom,
Ryan Moats, Robert Moore, Lee Rafalow, Kimberly Reger, and Kurt
Zeilenga during the development of the original LDAP Printer schema
[RFC3712].
The editors wish to acknowledge excellent comments from Nevil
Brownlee, Barry Leiba, Alexey Melnikov, Tom Petch, and Mike Sweet
during the development of this current version of the LDAP Printer
schema.
Thanks to the members of the IEEE-ISTO PWG IPP Working Group, for
their review comments and help in preparing this document.
14. Authors' Addresses
Please send comments to the authors at the addresses listed below.
Pat Fleming
Independent
51796 171 Ave
Pine Island, MN 55963
USA
Phone: +1 507-356-8277
Email: patfleminghtc@gmail.com
Fleming, McDonald Expires 30 October 2015 [Page 59]
Internet-Draft LDAP Schema for Printer Services 30 April 2015
Ira McDonald
High North Inc
221 Ridge Ave
Grand Marais, MI 49839
USA
Phone: +1 906-494-2434
Email: blueroofmusic@gmail.com
Fleming, McDonald Expires 30 October 2015 [Page 60]
