Internet DRAFT - draft-moreno-lisp-uberlay
draft-moreno-lisp-uberlay
Network Working Group V. Moreno
Internet-Draft Google LLC
Intended status: Experimental D. Farinacci
Expires: 1 April 2023 lispers.net
A. Rodriguez-Natal
M. Portoles-Comeras
F. Maino
S. Hooda
Cisco Systems
28 September 2022
Uberlay Interconnection of Multiple LISP overlays
draft-moreno-lisp-uberlay-06
Abstract
This document describes the use of the Locator/ID Separation Protocol
(LISP) to interconnect multiple disparate and independent network
overlays by using a transit overlay. The transit overlay is referred
to as the "uberlay" and provides connectivity and control plane
abstraction between different overlays. Each network overlay may use
different control and data plane approaches and may be managed by a
different organization. Structuring the network into multiple
network overlays enables the interworking of different overlay
approaches to data and control plane methods. The different network
overlays are autonomous from a control and data plane perspective,
this in turn enables failure survivability across overlay domains.
This document specifies the mechanisms and procedures for the
distribution of control plane information across overlay sites and in
the uberlay as well as the lookup and forwarding procedures for
unicast and multicast traffic within and across overlays. The
specification also defines the procedures to support inter-overlay
mobility of EIDs and their integration with the intra-overlay EID
mobility procedures defined in draft-ietf-lisp-eid-mobility.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Moreno, et al. Expires 1 April 2023 [Page 1]
Internet-Draft LISP Uberlay September 2022
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 1 April 2023.
Copyright Notice
Copyright (c) 2022 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Definition of Terms . . . . . . . . . . . . . . . . . . . . . 3
3. Interconnecting multiple LISP site-overlays via the
Uberlay . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1. Logical Topology Considerations . . . . . . . . . . . . . 7
4. General Procedures . . . . . . . . . . . . . . . . . . . . . 9
4.1. Control Plane Procedures . . . . . . . . . . . . . . . . 9
4.1.1. Split-horizon at the Border xTRs . . . . . . . . . . 11
4.1.2. Border-xTR Resiliency . . . . . . . . . . . . . . . . 11
4.2. Resolution and Forwarding Procedures . . . . . . . . . . 12
4.2.1. Multi-overlay requests at border xTR . . . . . . . . 13
4.3. Default EID registration and treatment . . . . . . . . . 14
5. Multicast Specific Procedures . . . . . . . . . . . . . . . . 15
5.1. Inter-site-overlay Control Plane Procedures for Signal-free
multicast . . . . . . . . . . . . . . . . . . . . . . . . 15
5.2. Border xTR Resolution and Forwarding procedures for
Signal-free multicast . . . . . . . . . . . . . . . . . . 15
6. Inter site-overlay Mobility Procedures . . . . . . . . . . . 16
7. Virtual Private Network (VPN) Considerations . . . . . . . . 17
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 18
Moreno, et al. Expires 1 April 2023 [Page 2]
Internet-Draft LISP Uberlay September 2022
9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 18
10. References . . . . . . . . . . . . . . . . . . . . . . . . . 18
10.1. Normative References . . . . . . . . . . . . . . . . . . 18
10.2. Informative References . . . . . . . . . . . . . . . . . 18
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 20
1. Introduction
The main motivation for this specification is to provide a
methodology for the interconnection of LISP domains that may use
disparate control and/or data plane approaches. For instance, one
domain may use native LISP encapsulation for its data plane and a DDT
based mapping system, while another domain may use VXLAN-GPE
encapsulation and a mapping system based on
[I-D.farinacci-lisp-decent]. Furthermore, one domain may use an IPv4
RLOC space and the other domain may use an IPv6 RLOC space and there
may not be connectivity between the domains at the RLOC level. We
propose a method to interconnect and enable interoperability between
these disparate LISP overlay networks by connecting them to a common
transit LISP overlay.
In order to provide interworking across implementations of overlays
that may use different control and data plane approaches, a LISP
network may be structured as a collection of site-overlays
interconnected by a transit area. Each site-overlay is a fully
functional overlay network and has its own set of Map Servers and Map
Resolvers. Site-overlays share a border xTR with a transit area.
Connectivity between site-overlays is provided via the transit area
which we will refer to as "The Uberlay". This specification
describes the Control Plane and Forwarding procedures for the
implementation of an Uberlay connected multi-overlay LISP network.
This approach to the structure of a LISP network may also enable
regional failure survivability and fault isolation.
2. Definition of Terms
LISP related terms, notably Map-Request, Map-Reply, Ingress Tunnel
Router (ITR), Egress Tunnel Router (ETR), Map-Server (MS) and Map-
Resolver (MR) are defined in the LISP specification [RFC6830].
Terms defining interactions with the LISP Mapping System are defined
in [RFC6833].
Terms related to the procedures for signal free multicast are defined
in [RFC8378].
The following terms are here defined to facilitate the descriptions
and discussions within this particular document.
Moreno, et al. Expires 1 April 2023 [Page 3]
Internet-Draft LISP Uberlay September 2022
Site-Overlay - Overlay network at a specific area or domain. This
overlay network has a dedicated Mapping System.
Border-xTR - xTR that connects a site-overlay to one or more
uberlays.
xTR - LISP Tunnel Router as defined in [RFC6833]. An xTR connects
end-points to the site-overlay.
Local Mapping System - Mapping system of the site-overlay
Uberlay - Overlay network that interconnects different site-overlays
to each other. The Uberlay has a dedicated Mapping System and
creates an overlay amongst the border xTRs which connect different
site-overlays.
Uberlay Mapping System - Autonomous mapping system dedicated to the
uberlay.
Site-Overlay EIDs - Also referred to as local site-overlay EIDs,
these are the EIDs that are connected to xTRs in a particular site-
overlay and are registered in their own local site-overlay mapping
system. These EIDs will also be registered in the uberlay but not in
the remote site-overlay mapping systems.
Remote site-overlay EIDs - These are EIDs connected and registered in
site-overlays other than the local site-overlay.
Local site-overlay EIDs - These are EIDs connected and registered in
the local site-overlay.
3. Interconnecting multiple LISP site-overlays via the Uberlay
A LISP network can be structured as a collection of LISP site-
overlays that are interconnected by one or more LISP Uberlays.
A LISP site-overlay is an overlay network that has its own set of
xTRs, its own dedicated Mapping System and it may have a dedicated
RLOC space, separate from that of other site-overlays or the uberlay.
A LISP uberlay is also an overlay network with its own set of xTRs,
its own dedicated Mapping System and it may have its own dedicated
RLOC space. When the RLOC spaces are dedicated, RLOC routes in the
local underlay do not leak across to the underlay of other site-
overlays.
A site-overlay will have xTRs and Border xTRs. The xTRs provide
connectivity to the local site-overlay EIDs, which are the EIDs that
are locally connected to the overlay-site. The Border xTRs are Re-
Moreno, et al. Expires 1 April 2023 [Page 4]
Internet-Draft LISP Uberlay September 2022
encapsulating Tunnel Routers (RTRs) that connect the site-overlays to
the LISP Uberlay in the transit network. xTRs participate in one
site-overlay and one site-overlay only. Border xTRs participate in
the mapping system of the site-overlay it resides in and the mapping
system of the uberlay it connects the site-overlay to. Border xTRs
may be shared by more than one site-overlay.
The different site-overlays can be interconnected by an uberlay. The
uberlay consists of a dedicated Mapping System and the set of Border
xTRs that connect the participating site-overlays to the Uberlay and
the Uberlay Mapping System.
Each site-overlay will have its own set of Map Servers and Map
Resolvers (MS/MRs) which operate as an autonomous Mapping System.
The Uberlay Mapping System is also autonomous and includes all
necessary Map Servers and Map Resolvers. Any of the Mapping Systems,
in site-overlays or in the Uberlay, follow the control plane
specification in [RFC6833] and may be structured as a Distributed
Delegation Tree (DDT) per [RFC8111]for the purposes of horizontal
scaling or other optimizations within each Mapping System.
The MS/MRs can be co-located with the border-xTRs of the site-overlay
When a Border xTR services more than one site-overlay, and the MS/MRs
are instantiated on the Border xTR, logical instances of MS/MRs must
be dedicated to each site-overlay.
This specification defines the interaction between the Mapping
Systems of the site-overlays and the uberlay to deliver a multi-
overlay hierarchical network. The forwarding procedures relevant to
the border xTRs are also specified. Figure 1 illustrates the multi-
overlay network.
Moreno, et al. Expires 1 April 2023 [Page 5]
Internet-Draft LISP Uberlay September 2022
+-------------------------------+
| +-----+ +-----+ +-----+ |
| | xTR | | xTR | | xTR | |
| +-----+ +-----+ +-----+ |
| |
| +-------+ | RLOC space 1
| Site Overlay 1 | MS/MR | | (underlay 1)
| +-------+ |
| |
| |
| +--------+ +--------+ |
+-----| Border |--| Border |----+
+-----| xTR |--| xTR |----+
| +--------+ +--------+ |
| |
| |
| |
| +-------+ | Uberlay
| Uberlay | MS/MR | | RLOC Space
| +-------+ | (Transit Underlay)
| |
| |
| +----------+ |
+---------| Border |----------+
+---------| xTR |----------+
| +----------+ |
| |
| +-------+ | RLOC space 2
| Site Overlay 2 | MS/MR | | (underlay 2)
| +-------+ |
| |
| +-----+ +-----+ +-----+ |
| | xTR | | xTR | | xTR | |
| +-----+ +-----+ +-----+ |
+-------------------------------+
Figure 1. Site-overlays connected via Uberlay
Structuring the LISP network as multiple site-overlays interconnected
by an uberlay delivers the following benefits:
* Enable the interworking of diverse site-overlay implementations in
which different mapping systems and encapsulations may be used.
* Enhanced resiliency through regional failure survivability.
Failures in one site-overlay or failures in a portion of the
underlay should not affect other site-overlays.
Moreno, et al. Expires 1 April 2023 [Page 6]
Internet-Draft LISP Uberlay September 2022
* Reduce the state of the site-overlay control plane. The site-
overlay control plane will only maintain state for EIDs that are
connected to xTRs within the site-overlay These EIDs are referred
to as local site-overlay EIDs in this specification. Remote site-
overlay EIDs will not be explicitly registered within the site-
overlay.
* Separate the RLOC space of the different site-overlays as well as
the uberlay RLOC space. Each site-overlay will only need
reachability to its own RLOCs, making the RLOCs private to the
site-overlay Similarly, the uberlay RLOC space does not require
knowledge of site-overlay specific RLOCs. This simplifies the
underlay routing protocol structure and reduces the state that
must be handled and maintained by the underlay routing protocols.
* Reduced latency for local site-overlay EID registrations may be
achieved when xTRs and Map Servers are topologically close.
Topological proximity is expected when the RLOC spaces for the
different overlays are kept separate.
* Reduced latency for local site-overlay EID lookups may be achieved
when xTRs, Map Resolvers and Map Servers are topologically close.
Topological proximity is expected when the RLOC spaces for the
different overlays are kept separate.
* Creates a multicast replication hierarchy where the Border RTRs
serve as the points of multicast replication for multicast traffic
that spans multiple site-overlays.
* Creates a distributed structure of RTRs that can be leveraged for
the deployment of NAT traversal in the RLOC space.
3.1. Logical Topology Considerations
xTRs as defined in RFC6833bis connect a network to the LISP overlay
and register the EID prefixes from the connected network to the LISP
mapping system. Border xTRs, as defined in this document, will
connect site-overlays to the Uberlay and register the EID prefixes
that originate in a site-overlay in the Mapping System of the
Uberlay. Conversely, a border xTR may register EID prefixes present
in the Uberlay Mapping System into the Mapping System of a particular
site-overlay. Furthermore, border xTRs may connect Uberlays to each
other and register the EID prefixes from one Uberlay into the other.
There is no provision for the detection of registration loops when
concatenating site-overlays and Uberlays, thus any interconnection of
overlay domains (site-overlays or Uberlays) must be done in a loop
free topology.
Moreno, et al. Expires 1 April 2023 [Page 7]
Internet-Draft LISP Uberlay September 2022
A loop free topology is hereby defined for reference. This is a
general concept and is not encoded into any of the protocol messages
in LISP. A loop free topology limits the peerings between Uberlays
and/or overlays to a strict hierarchy. At the top of the hierarchy
is a single central Uberlay or Core Uberlay. The loop free topology
is defined by two simple rules: Uberlays must only connect to
Uberlays in the next consecutive level of hierarchy (no level
skipping) and uberlays within the same level of hierarchy must not
connect to each other. The loop-free topology hierarchy is
illustrated in Figure 2.
+----------------+ +----------------+
| site-overlay 1 | | site-overlay 2 |
| (Level 2) | | (Level 2) |
+----------------+ +----------------+
+---+ +---+
|RTR| |RTR|
+---+ +---+
+-----------+ +-----------+
| Uberlay 1 | | Uberlay 2 |
| (Level 1) | | (Level 1) |
+-----------+ +-----------+
+---+ +---+
|RTR+---------+RTR|
+--++ ++--+
| Core |
| Uberlay |
| (Level 0) |
+--++ ++--+
|RTR+---------+RTR|
+---+ +---+
+-----------+ +-----------+
| Uberlay 3 | | Uberlay 4 |
| (Level 1) | | (Level 1) |
+-----------+ +-----------+
+---+ +---+
|RTR| |RTR|
+---+ +---+
+----------------+ +----------------+
| site-overlay 3 | | site-overlay 4 |
| (Level 2) | | (Level 2) |
+----------------+ +----------------+
Figure 2. Loop-free topology hierarchy
Moreno, et al. Expires 1 April 2023 [Page 8]
Internet-Draft LISP Uberlay September 2022
4. General Procedures
A site-overlay maintains state only for its local site-overlay EIDs
and RLOCs. Tunnels never cross site-overlay or uberlay boundaries.
Remote site-overlay EIDs are reachable at the source site-overlay via
a default mapping which will steer all traffic destined to remote
site-overlay EIDs to the border xTRs where it can be handed off to
the uberlay. Traffic will be decapsulated at the border xTRs and a
lookup in the uberlay mapping system will determine the site-overlay
to which traffic is to be re-encapsulated. The uberlay maintains
state for the EIDs of all interconnected site-overlays and will steer
traffic from the source site-overlay to the destination site-overlay
by encapsulating the traffic from the source site-overlay border xTR
to the destination site-overlay border xTR. At the border xTR of the
destination site-overlay, traffic will be de-capsulated, a lookup in
the local destination site-overlay Mapping System will take place and
traffic will be re-encapsulated to the xTR that connects to the
destination EID. Thus, forwarding is achieved by concatenating
overlays and doing Re-encapsulation at the border xTRs to forward the
traffic from the Ingress site-overlay to the Egress site-overlay via
the Uberlay.
Traffic for non-LISP sites, or for EIDs not registered in any site-
overlay, will also be forwarded to the border xTR where it will be
forwarded or dropped as appropriate.
4.1. Control Plane Procedures
Local EIDs must be registered by the xTRs into the local Mapping
System of the site-overlay. Intra-site communication follows the
standard procedures of registration, resolution, caching and
encapsulation defined in [I-D.ietf-lisp-rfc6830bis] and
[I-D.ietf-lisp-rfc6833bis] amongst the xTRs within the local site-
overlay.
Moreno, et al. Expires 1 April 2023 [Page 9]
Internet-Draft LISP Uberlay September 2022
The border xTRs at a site-overlay should have a local site-overlay
RLOC-set and will also have an uberlay RLOC-set. The local site-
overlay RLOC-set is in the private site-overlay RLOC space and is
used by the border xTRs as the RLOC set for any mappings it may
register with the site-overlay Mapping System. The uberlay RLOC-set
for the border-xTRs of a particular site-overlay are the RLOCs to
reach the site-overlay in the uberlay RLOC space. The border xTR
will use the uberlay RLOC-set in any mappings it may register with
the uberlay Mapping System. It is possible for a deployment to
connect the RLOC spaces of the site-overlays and the uberlay, it is
also possible in the scenario of a common RLOC space for the uberlay
and local site-overlay RLOC sets to be one and the same. Any
implementation of this specification should support disjoint RLOC
spaces or joint RLOC spaces.
The border xTRs must register a default EID-prefix as specified in
Section 4.3 with the local site-overlay Mapping System. Remote EIDs
will be generally reachable by xTRs in a site-overlay using the
default EID mapping registered by the border xTRs. This is expected
to be the mapping used for most communications to remote site-overlay
EIDs. Remote site-overlay EIDs may be registered with the local
site-overlay Mapping System for the purposes of supporting inter-
overlay EID mobility as specified in Section 6, these mappings will
be preferred over the default EID mapping whenever present.
Local EIDs registered with the site-overlay mapping system must also
be registered with the Uberlay Mapping System. The registration of
the local site-overlay EIDs with the uberlay Mapping System is
originated by the Border xTRs. The local site-overlay EIDs SHOULD be
aggregated into the shortest covering prefix possible before being
registered with the uberlay Mapping System. How this aggregation is
achieved is implementation specific.
In order to be able to register the local site-overlay EIDs with the
uberlay Mapping System, the border xTRs must subscribe to all EIDs
registered in their local site-overlay Mapping System. This is a
subscription to 0.0.0.0/0 (or 0::/0) with the N-bit set as specified
in [I-D.ietf-lisp-pubsub]. The subscription populates all local
site-overlay EID mappings in the map-cache of the border xTRs.
Once received through the subscription, the local site-overlay EIDs
in the map-cache at the border xTRs must be registered by the border
xTRs with the uberlay Mapping System. The local site-overlay EIDs
will be registered using the 'uberlay' RLOC-set for the registering
border xTR.
Moreno, et al. Expires 1 April 2023 [Page 10]
Internet-Draft LISP Uberlay September 2022
Following [I-D.ietf-lisp-eid-mobility], the border xTRs will also
subscribe to any EID prefixes it registers with the uberlay Mapping
System. This allows the border xTRs to get Map Notify messages from
the uberlay Mapping System for EID prefixes that may move from their
local site-overlay to a remote site-overlay.
4.1.1. Split-horizon at the Border xTRs
Remote site-overlay EIDs may be learnt at a border xTR due to
resolution of a remote destination EID or due to a mobility event as
specified in Section 6. Remote site-overlay EIDs learnt from the
uberlay will be installed in the map-cache of the border xTR with the
corresponding remote uberlay RLOC-set for the remote border xTR.
When these remote site-overlay EIDs are learnt as a consequence of
the map-notify messages defined in the Inter-overlay mobility
procedures in Section 6, the EIDs will also be registered with the
local site-overlay mapping system using the local site-overlay RLOC-
set for the border-xTR. The remote site-overlay EIDs registered with
the local site-overlay mapping system will be learnt back at the
border xTR because of the border xTR's subscription to all local
site-overlay EIDs. This can cause the mapping for the remote EID
that is installed in the border xTR map-cache to flip flop between
the uberlay RLOC-set and the local site-overlay RLOC-set.
In order to avoid this flip flopping a split horizon procedure must
be implemented. When a mapping received at the border xTR (as part
of its subscription to all local site-overlay EID prefixes) has the
local site-overlay RLOC-set for the border xTR, the mapping received
in the subscription corresponds to a remote site-overlay EID and
should be ignored by the border xTR. The mapping should not be
installed in the map-cache of the border xTR and the EIDs in the
mapping should not be advertised to the uberlay. More robust split
horizon mechanisms can be proposed in future revisions of this
specification.
4.1.2. Border-xTR Resiliency
Redundancy at the border xTRs requires that border xTRs be logically
grouped so that the redundant array doesn't create a registration
loop. As border xTRs interconnect overlay domains, the border xTRs
will register the EID prefixes from one domain into the neighboring
domain. From the perspective of the border xTR, the EID prefixes to
be registered in one domain are learnt from a neighbor domain which
we will refer to as the "site-of-origin". The site-of-origin may be
an overlay-site, an Uberlay or an IP network.
Moreno, et al. Expires 1 April 2023 [Page 11]
Internet-Draft LISP Uberlay September 2022
Border xTRs should be logically grouped in Border Sets. A border set
is a group of border xTRs that register EID prefixes from the same
site-of-origin. Members of a border set will register the EIDs from
a particular site-of-origin into the neighboring overlay (site-
overlay or uberlay) using a common site-id. The use of the site-ID
namespace is locally significant to each overlay domain (site-overlay
or Uberlay) and does not require cross-domain synchronization or
dispersion. A border-xTR may be a member of multiple border sets to
allow different site-of-origin domains to be serviced by the border-
xTR. Note that not all site-of-origin domains will connect to the
same combination of border-xTRs.
EID Mappings will be tagged with a site-ID according to their site-
of-origin when they are registered by the border-xTR. The site-ID
must be maintained in the Mapping System as part of the registration
record. EID Mappings published and received at the border xTR must
include the site-ID for the EID Mapping. If the border-xTR receives
a mapping for an EID with a site-ID that matches the site-ID for one
of its border sets (site-of-origin), the Border xTR will not register
that information to the site-of-origin associated with that site-ID
and thus prevent any registration loops from occurring.
4.2. Resolution and Forwarding Procedures
Intra-site communication follows the standard procedures of
registration, resolution, caching and encapsulation defined in
[I-D.ietf-lisp-rfc6830bis] and [I-D.ietf-lisp-rfc6833bis] amongst the
xTRs within the local site-overlay.
Inter-site communication is achieved by encapsulating traffic
destined to remote site-overlay EIDs from the xTRs to the border
xTRs. Traffic will be decapsulated at the border xTRs and a lookup
in the uberlay mapping system will determine the site-overlay to
which traffic is to be re-encapsulated. The lookup should return the
uberlay RLOCs for the border xTRs of the site-overlay where the
destination EID is located. At the border xTR of the destination
overlay-site, traffic will be de-capsulated, and re-encapsulated to
the destination xTR, just like an RTR does. The border xTR already
has the destination EID in its cache per its subscription to all
local site-overlay EIDs.
When receiving encapsulated traffic, a border xTR will de-capsulate
the traffic and will do a lookup for the destination EID in its map
cache. If the destination EID is present in the map cache, the
traffic is forwarded and no lookup takes place. If the destination
EID is not present in the cache, the destination EID is not in any
local site-overlay connected to the border xTR, in which case the
border xTR will issue a map-request to all Uberlay Mapping Systems it
Moreno, et al. Expires 1 April 2023 [Page 12]
Internet-Draft LISP Uberlay September 2022
is connected to. The criteria to determine which Mapping Systems are
Uberlay Mapping Systems is simply to select those Mapping Systems
with which the border xTR doesn't hold a subscription to 0.0.0.0/0
(or 0::/0).
4.2.1. Multi-overlay requests at border xTR
A Border xTR may query all Mapping Systems in all uberlays it
participates in. The border xTR will then chose based on longest
prefix match the more specific EID mapping provided by any of the
Mapping Systems. This procedure could also include site-overlay
Mapping Systems, however those are not expected to be queried as the
border xTR subscribes to all EIDs in the site-overlays and the
presence of the mappings in the cache will prevent any lookups. The
processing of Map Requests following the multi-domain request logic
works as follows:
1. The Border xTR sends a map request for the prefix that it intends
to resolve to each of the uberlay Mapping Systems it participates
in.
2. The Border xTR receives Map Replies from each of the different
uberlay Mapping Systems it sent requests to. The Border xTR will
treat the replies differently depending on their contents:
* Negative Map Replies (NMR) are ignored and discarded unless
all Map Replies received are Negative, then the border xTR
follows the procedures specified in [RFC6833] for Negative Map
Replies.
* Map Replies with RLOCs that belong to the requesting border
xTR are ignored.
* Map Replies with EID prefixes that are not already in the map
cache of the border xTR are accepted and cached.
* If the EID prefix received in the Map-Reply already exists in
the cache/routing table, but the Map-Reply contains a
different RLOC-set than the one cached, the mappings are
merged so that the RLOCs received in the Map-Reply are added
to the RLOC-set previously cached for the EID prefix.
* If the EID prefix received in the Map-Reply is more specific
or less specific than an EID prefix already cached, the
mapping received MUST be cached.
Moreno, et al. Expires 1 April 2023 [Page 13]
Internet-Draft LISP Uberlay September 2022
It is expected that a deployment of the uberlay would include the
dynamic registration of default EIDs. It is also recommended that an
implementation adopts mechanisms for the dynamic resolution of
default EIDs. In an environment leveraging the dynamic registration
and resolution of default EIDs, the border xTR should not receive
Negative Map-Replies, but all replies (including those in response to
requests for destinations that are external to the EID space) will be
Map-replies with a non-zero locator count. Nevertheless, an
implementation could opt to not use dynamic default-EID handling. In
these cases, the border xTR will receive NMRs. The implementation of
the Border xTR should defer the decision on caching an NMR until all
relevant Map-replies are received. To this effect, the
implementation should implement mechanisms to ensure that sufficient
replies are received before programming the map-cache. The
mechanisms by which this is achieved are an implementation specific
matter and therefore not specified in this document.
When following these rules to process multi-domain requests, the
Border xTR guarantees proper discovery and use of destination
prefixes that will be associated with their corresponding overlay-
site. By ignoring the negative replies the procedure works
regardless of whether the Mapping Systems of multiple uberlays have
consistent configurations or operate individually without being aware
of the whole addressing space in the overlay fabric.
4.3. Default EID registration and treatment
Border xTRs will register a mapping to be used as a default mapping
to handle the forwarding of traffic destined to any EIDs that are not
explicitly registered. These mappings will be registered in the
local site-overlay Mapping System of each site-overlay. The RLOCs
for the mappings will be the site-overlay RLOCs of the border xTR.
This registration is intended to instruct the Mapping System to
follow the procedures in [RFC6833] for Negative Map Replies and
calculate the broadest non-registered EID prefix that includes the
requested destination EID and issue a map-reply with the calculated
EID and the RLOCs registered by the border xTRs. The map-reply for
this default mapping will have a shorter TTL to accommodate any
changes in the registrations.
The instruction to the Mapping System can be encoded as the
registration of an agreed upon distinguished name
[I-D.ietf-lisp-name-encoding]such as "Default". The registration
will contain the RLOC set desired for the default handling.
Moreno, et al. Expires 1 April 2023 [Page 14]
Internet-Draft LISP Uberlay September 2022
5. Multicast Specific Procedures
This specification will focus on the procedures necessary to extend
signal-free multicast [RFC8378] across multiple site-overlays
interconnected with an uberlay. The specification will focus on the
extensions of the Sender and Receiver site procedures
5.1. Inter-site-overlay Control Plane Procedures for Signal-free
multicast
1. At the listener sites, xTRs with multicast listeners will follow
the receiver site procedures described in [RFC8378]. A
replication list will be built and registered on the site-overlay
Mapping System for the multicast channel being joined by the
listeners.
2. The Mapping System for the listener site-overlay will send Map-
Notify messages towards the multicast source or RP per [RFC8378].
The multicast source or RP is reachable via the border-xTRs of
the listener site-overlay via the default EID mapping registered
in the listener site-overlay.
3. Upon reception of the Map-Notify in the previous step, the
listener site-overlay border-xTR will register the multicast EID
with the uberlay Mapping System using the uberlay RLOCs for its
site-overlay as the RLOC set for the mapping being registered.
Only one of the RLOCs in the set should be active in the
registration per the procedures in [RFC8378]. A replication tree
is built in the uberlay as specified in [RFC8378].
4. After the listener site-overlay border-xTR registers the
multicast EID with the uberlay Mapping system, the uberlay MS
will send a Map-Notify toward the multicast source per [RFC8378]
5. Upon reception of the Map-Notify in the previous step, the border
xTR at the source site-overlay registers its interest in the
multicast EID with the source site-overlay Mapping System
following the procedures described in [RFC8378].
5.2. Border xTR Resolution and Forwarding procedures for Signal-free
multicast
The mapping resolution procedures for multicast EIDs at border xTRs
fall within the scope of the mechanisms specified in Section 4. The
Map-replies obtained from the lookup will follow the behavior
specified in [RFC8378] for signal-free multicast.
Moreno, et al. Expires 1 April 2023 [Page 15]
Internet-Draft LISP Uberlay September 2022
Forwarding will also follow the General Procedures specified in
Section 4 without alteration. It is worth noting that the
concatenation of overlays between listener sites, uberlay and sender
site-overlays creates a convenient replication structure where the
border xTRs act as the replication points to form an optimized end-
to-end multi-level replication tree.
6. Inter site-overlay Mobility Procedures
The receiver and sender site procedures defined in
[I-D.ietf-lisp-eid-mobility] apply without change to each site-
overlay and to the uberlay. Border xTRs are connected to two or more
overlay networks which are following the mobility procedures. An
away table is defined at the border xTR for each overlay network it
participates in. In order to illustrate the procedures required,
this specification describes a scenario where a border xTR has one
local site-overlay away table and one uberlay facing away table. The
procedures for mobility described in this section are extensible to
border xTRs participating in more than two overlays.
When a map notify for an EID is received at an xTR, an away entry is
created on the receiving side table. Any away entries for the
specific EID in other tables on the same LISP node (xTR or RTR) must
be removed. This general rule addresses convergence necessary for a
first move as well as any subsequent moves (moves that take place
after the away tables are already populated with entries for the
moving EID due to previous moves).
The following set of procedures highlights any additions to the
mobility procedures defined in [I-D.ietf-lisp-eid-mobility]:
1. Detect the roaming EID per the mechanisms described in
[I-D.ietf-lisp-eid-mobility] and register the EID with the site-
overlay Mapping System at the landing site-overlay
2. The site-overlay Mapping System at the landing site-overlay must
send a Map-Notify to the last registrant xTR (if it is local to
the site-overlay) and to the border xTR as the border xTR
subscribes to all EIDs in the site-overlay.
3. The border xTR will install an entry for the moved host in the
local away table of the border xTR.
4. The border xTR from the landing site-overlay will register the
roaming EID with the uberlay Mapping System using the uberlay
RLOC-set for the landing site-overlay
Moreno, et al. Expires 1 April 2023 [Page 16]
Internet-Draft LISP Uberlay September 2022
5. The Uberlay Map Server will send Map-Notify messages to the
border xTRs at the departure site-overlay as specified in
[I-D.ietf-lisp-eid-mobility] (border xTR with the previously
registered RLOCs).
6. Upon reception of the Map-Notify, the border xTR must check if
the Map-Notify is for an EID-prefix that is covered by a broader
or equal EID-prefix that is locally registered. Local
registration is determined by the presence of the broader or
equal EID prefix in the map-cache of the border xTR.
7. If the roaming EID-prefix received in the Map-Notify is not
covered under a previously registered EID-prefix in the local
site-overlay, the EID-prefix is a newly registered prefix and no
further action is required.
8. If the roaming EID-prefix received in the Map-Notify is covered
under a registered EID-prefix, the Map-Notify is due to a move
event. In this case, the site-overlay border xTR must register
the roaming EID prefix in the site-overlay mapping system using
the site-overlay facing RLOC-set of the border-xTRs. The
roaming EID-prefix must also be installed in the uberlay facing
away table of the border xTR at the departure site-overlay.
9. The departure site-overlay Map-Server will send Map-Notify
messages to the xTRs at the departure site-overlay as specified
in [I-D.ietf-lisp-eid-mobility] (edge xTRs with the previously
registered RLOCs).
10. When the site-overlay xTR at the departure site-overlay receives
the Map-Notify from the border xTR, it will include the EID
prefix received in the Map-Notify in its away table per the
procedures described in [I-D.ietf-lisp-eid-mobility].
11. Data triggered Solicit Map Requests (SMRs) will be initiated in
the different site-overlays and the uberlay as traffic matches
the different away tables. As specified in
[I-D.ietf-lisp-eid-mobility], these SMRs notify the different
ITRs involved in communications with the roaming EID that they
must issue a new Map-Request to the mapping system to renew
their mappings for the roaming EID.
7. Virtual Private Network (VPN) Considerations
When supporting multiple Instance IDs as specified in
[I-D.ietf-lisp-vpn] the Instance IDs range is divided in two sets. A
reuse-set that can be used in each site-overlay and a global-set used
across site-overlays and the uberlay.
Moreno, et al. Expires 1 April 2023 [Page 17]
Internet-Draft LISP Uberlay September 2022
Instance-IDs that are local to a site-overlay should only provide
intra-overlay connectivity and are in the site-overlay mapping system
only for VPN use for the xTRs in the site-overlay. When the VPN
reaches across site-overlays, then the global-set instance-IDs are in
the uberlay mapping system as well as each site-overlay mapping
system where the VPN members exist.
8. IANA Considerations
This document has no IANA implications
9. Acknowledgements
The authors want to thank Kedar Karamarkar, Prakash Jain and Vina
Ermagan for their insightful contribution to shaping the ideas in
this document. We would also like to acknowledge the valuable input
from the workgroup chairs Joel Halpern and Luigi Iannone in refining
the objectives of the document.
10. References
10.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC3618] Fenner, B., Ed. and D. Meyer, Ed., "Multicast Source
Discovery Protocol (MSDP)", RFC 3618,
DOI 10.17487/RFC3618, October 2003,
<https://www.rfc-editor.org/info/rfc3618>.
[RFC4601] Fenner, B., Handley, M., Holbrook, H., and I. Kouvelas,
"Protocol Independent Multicast - Sparse Mode (PIM-SM):
Protocol Specification (Revised)", RFC 4601,
DOI 10.17487/RFC4601, August 2006,
<https://www.rfc-editor.org/info/rfc4601>.
[RFC4607] Holbrook, H. and B. Cain, "Source-Specific Multicast for
IP", RFC 4607, DOI 10.17487/RFC4607, August 2006,
<https://www.rfc-editor.org/info/rfc4607>.
10.2. Informative References
[I-D.farinacci-lisp-decent]
Farinacci, D. and C. Cantrell, "A Decent LISP Mapping
System (LISP-Decent)", Work in Progress, Internet-Draft,
Moreno, et al. Expires 1 April 2023 [Page 18]
Internet-Draft LISP Uberlay September 2022
draft-farinacci-lisp-decent-10, 15 August 2022,
<https://www.ietf.org/archive/id/draft-farinacci-lisp-
decent-10.txt>.
[I-D.ietf-lisp-eid-mobility]
Comeras, M. P., Ashtaputre, V., Maino, F., Moreno, V., and
D. Farinacci, "LISP L2/L3 EID Mobility Using a Unified
Control Plane", Work in Progress, Internet-Draft, draft-
ietf-lisp-eid-mobility-10, 10 July 2022,
<https://www.ietf.org/archive/id/draft-ietf-lisp-eid-
mobility-10.txt>.
[I-D.ietf-lisp-name-encoding]
Farinacci, D., "LISP Distinguished Name Encoding", Work in
Progress, Internet-Draft, draft-ietf-lisp-name-encoding-
00, 6 September 2022, <https://www.ietf.org/archive/id/
draft-ietf-lisp-name-encoding-00.txt>.
[I-D.ietf-lisp-pubsub]
Rodriguez-Natal, A., Ermagan, V., Cabellos, A., Barkai,
S., and M. Boucadair, "Publish/Subscribe Functionality for
LISP", Work in Progress, Internet-Draft, draft-ietf-lisp-
pubsub-09, 28 June 2021, <https://www.ietf.org/archive/id/
draft-ietf-lisp-pubsub-09.txt>.
[I-D.ietf-lisp-rfc6830bis]
Farinacci, D., Fuller, V., Meyer, D., Lewis, D., and A.
Cabellos, "The Locator/ID Separation Protocol (LISP)",
Work in Progress, Internet-Draft, draft-ietf-lisp-
rfc6830bis-38, 7 May 2022,
<https://www.ietf.org/archive/id/draft-ietf-lisp-
rfc6830bis-38.txt>.
[I-D.ietf-lisp-rfc6833bis]
Farinacci, D., Maino, F., Fuller, V., and A. Cabellos,
"Locator/ID Separation Protocol (LISP) Control-Plane",
Work in Progress, Internet-Draft, draft-ietf-lisp-
rfc6833bis-31, 2 May 2022,
<https://www.ietf.org/archive/id/draft-ietf-lisp-
rfc6833bis-31.txt>.
[I-D.ietf-lisp-vpn]
Moreno, V. and D. Farinacci, "LISP Virtual Private
Networks (VPNs)", Work in Progress, Internet-Draft, draft-
ietf-lisp-vpn-09, 10 July 2022,
<https://www.ietf.org/archive/id/draft-ietf-lisp-vpn-
09.txt>.
Moreno, et al. Expires 1 April 2023 [Page 19]
Internet-Draft LISP Uberlay September 2022
[RFC6407] Weis, B., Rowles, S., and T. Hardjono, "The Group Domain
of Interpretation", RFC 6407, DOI 10.17487/RFC6407,
October 2011, <https://www.rfc-editor.org/info/rfc6407>.
[RFC6830] Farinacci, D., Fuller, V., Meyer, D., and D. Lewis, "The
Locator/ID Separation Protocol (LISP)", RFC 6830,
DOI 10.17487/RFC6830, January 2013,
<https://www.rfc-editor.org/info/rfc6830>.
[RFC6831] Farinacci, D., Meyer, D., Zwiebel, J., and S. Venaas, "The
Locator/ID Separation Protocol (LISP) for Multicast
Environments", RFC 6831, DOI 10.17487/RFC6831, January
2013, <https://www.rfc-editor.org/info/rfc6831>.
[RFC6833] Fuller, V. and D. Farinacci, "Locator/ID Separation
Protocol (LISP) Map-Server Interface", RFC 6833,
DOI 10.17487/RFC6833, January 2013,
<https://www.rfc-editor.org/info/rfc6833>.
[RFC7348] Mahalingam, M., Dutt, D., Duda, K., Agarwal, P., Kreeger,
L., Sridhar, T., Bursell, M., and C. Wright, "Virtual
eXtensible Local Area Network (VXLAN): A Framework for
Overlaying Virtualized Layer 2 Networks over Layer 3
Networks", RFC 7348, DOI 10.17487/RFC7348, August 2014,
<https://www.rfc-editor.org/info/rfc7348>.
[RFC8060] Farinacci, D., Meyer, D., and J. Snijders, "LISP Canonical
Address Format (LCAF)", RFC 8060, DOI 10.17487/RFC8060,
February 2017, <https://www.rfc-editor.org/info/rfc8060>.
[RFC8061] Farinacci, D. and B. Weis, "Locator/ID Separation Protocol
(LISP) Data-Plane Confidentiality", RFC 8061,
DOI 10.17487/RFC8061, February 2017,
<https://www.rfc-editor.org/info/rfc8061>.
[RFC8111] Fuller, V., Lewis, D., Ermagan, V., Jain, A., and A.
Smirnov, "Locator/ID Separation Protocol Delegated
Database Tree (LISP-DDT)", RFC 8111, DOI 10.17487/RFC8111,
May 2017, <https://www.rfc-editor.org/info/rfc8111>.
[RFC8378] Moreno, V. and D. Farinacci, "Signal-Free Locator/ID
Separation Protocol (LISP) Multicast", RFC 8378,
DOI 10.17487/RFC8378, May 2018,
<https://www.rfc-editor.org/info/rfc8378>.
Authors' Addresses
Moreno, et al. Expires 1 April 2023 [Page 20]
Internet-Draft LISP Uberlay September 2022
Victor Moreno
Google LLC
1600 Amphitheater Parkway
Mountain View, California 94043
United States of America
Email: vimoreno@google.com
Dino Farinacci
lispers.net
San Jose, CA 95120
United States of America
Email: farinacci@gmail.com
Alberto Rodriguez-Natal
Cisco Systems
170 Tasman Drive
San Jose, California 95134
United States of America
Email: natal@cisco.com
Marc Portoles-Comeras
Cisco Systems
170 Tasman Drive
San Jose, California 95134
United States of America
Email: mportole@cisco.com
Fabio Maino
Cisco Systems
170 Tasman Drive
San Jose, California 95134
United States of America
Email: fmaino@cisco.com
Sanjay Hooda
Cisco Systems
170 Tasman Drive
San Jose, California 95134
United States of America
Email: shooda@cisco.com
Moreno, et al. Expires 1 April 2023 [Page 21]