Internet DRAFT - draft-previdi-isis-segment-routing-extensions
draft-previdi-isis-segment-routing-extensions
IS-IS for IP Internets S. Previdi, Ed.
Internet-Draft C. Filsfils
Intended status: Standards Track A. Bashandy
Expires: August 17, 2014 Cisco Systems, Inc.
H. Gredler
Juniper Networks, Inc.
S. Litkowski
Orange
J. Tantsura
Ericsson
February 13, 2014
IS-IS Extensions for Segment Routing
draft-previdi-isis-segment-routing-extensions-05
Abstract
Segment Routing (SR) allows for a flexible definition of end-to-end
paths within IGP topologies by encoding paths as sequences of
topological sub-paths, called "segments". These segments are
advertised by the link-state routing protocols (IS-IS and OSPF).
This draft describes the necessary IS-IS extensions that need to be
introduced for Segment Routing.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 17, 2014.
Previdi, et al. Expires August 17, 2014 [Page 1]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
Copyright Notice
Copyright (c) 2014 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Previdi, et al. Expires August 17, 2014 [Page 2]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Segment Routing Identifiers . . . . . . . . . . . . . . . . . 4
2.1. SID/Label Sub-TLV . . . . . . . . . . . . . . . . . . . . 4
2.2. Prefix Segment Identifier (Prefix-SID Sub-TLV) . . . . . . 5
2.3. Adjacency Segment Identifier . . . . . . . . . . . . . . . 8
2.3.1. Adjacency Segment Identifier (Adj-SID) Sub-TLV . . . . 9
2.3.2. Adjacency Segment Identifiers in LANs . . . . . . . . 10
2.4. SID/Label Binding TLV . . . . . . . . . . . . . . . . . . 12
2.4.1. Flags . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4.2. Weight . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4.3. Range . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4.4. Prefix Length, Prefix . . . . . . . . . . . . . . . . 15
2.4.5. SID/Label Sub-TLV . . . . . . . . . . . . . . . . . . 15
2.4.6. ERO Metric sub-TLV . . . . . . . . . . . . . . . . . . 16
2.4.7. IPv4 ERO subTLV . . . . . . . . . . . . . . . . . . . 16
2.4.8. IPv6 ERO subTLV . . . . . . . . . . . . . . . . . . . 17
2.4.9. Unnumbered Interface ID ERO subTLV . . . . . . . . . . 17
2.4.10. IPv4 Backup ERO subTLV . . . . . . . . . . . . . . . . 18
2.4.11. IPv6 Backup ERO subTLV . . . . . . . . . . . . . . . . 19
2.4.12. Unnumbered Interface ID Backup ERO subTLV . . . . . . 19
2.4.13. Prefix ERO and Prefix Backup ERO subTLV path
semantics . . . . . . . . . . . . . . . . . . . . . . 20
3. Router Capabilities . . . . . . . . . . . . . . . . . . . . . 21
3.1. SR-Capabilities Sub-TLV . . . . . . . . . . . . . . . . . 21
3.2. SR-Algorithm Sub-TLV . . . . . . . . . . . . . . . . . . . 22
4. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 23
5. Manageability Considerations . . . . . . . . . . . . . . . . . 24
6. Security Considerations . . . . . . . . . . . . . . . . . . . 24
7. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 24
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 24
9. References . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9.1. Normative References . . . . . . . . . . . . . . . . . . . 24
9.2. Informative References . . . . . . . . . . . . . . . . . . 25
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 26
Previdi, et al. Expires August 17, 2014 [Page 3]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
1. Introduction
Segment Routing (SR) allows for a flexible definition of end-to-end
paths within IGP topologies by encoding paths as sequences of
topological sub-paths, called "segments". These segments are
advertised by the link-state routing protocols (IS-IS and OSPF). Two
types of segments are defined, Prefix segments and Adjacency
segments. Prefix segments represent an ecmp-aware shortest-path to a
prefix, as per the state of the IGP topology. Adjacency segments
represent a hop over a specific adjacency between two nodes in the
IGP. A prefix segment is typically a multi-hop path while an
adjacency segment, in most of the cases, is a one-hop path. SR's
control-plane can be applied to both IPv6 and MPLS data-planes, and
do not require any additional signaling (other than the regular IGP).
For example, when used in MPLS networks, SR paths do not require any
LDP or RSVP-TE signaling. Still, SR can interoperate in the presence
of LSPs established with RSVP or LDP.
This draft describes the necessary IS-IS extensions that need to be
introduced for Segment Routing.
Segment Routing architecture is described in
[I-D.filsfils-rtgwg-segment-routing].
Segment Routing use cases are described in
[I-D.filsfils-rtgwg-segment-routing-use-cases].
2. Segment Routing Identifiers
Segment Routing architecture ([I-D.filsfils-rtgwg-segment-routing])
defines different types of Segment Identifiers (SID). This document
defines the IS-IS encodings for the IGP-Prefix-SID, the IGP-
Adjacency-SID, the IGP-LAN-Adjacency-SID and the Binding-SID.
2.1. SID/Label Sub-TLV
The SID/Label Sub-TLV is present in multiple Sub-TLVs defined in this
document and contains a SID or a MPLS Label. The SID/Label Sub-TLV
has the following format:
Previdi, et al. Expires August 17, 2014 [Page 4]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SID/Label (variable) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
where:
Type: 1
Length: variable (3 or 4)
SID/Label: if length is set to 3 then the 20 rightmost bits
represent a MPLS label. If length is 4 then the value represents
a 32 bits SID.
2.2. Prefix Segment Identifier (Prefix-SID Sub-TLV)
A new IS-IS Sub-TLV is defined: the Prefix Segment Identifier Sub-TLV
(Prefix-SID Sub-TLV).
The Prefix-SID Sub-TLV carries the Segment Routing IGP-Prefix-SID as
defined in [I-D.filsfils-rtgwg-segment-routing]. The 'Prefix SID'
must be unique within a given IGP domain. The 'Prefix SID' is an
index to determine the actual SID/label value inside the set of all
advertised SID/label ranges of a given router. A receiving router
uses the index to determine the actual SID/label value in order to
construct forwarding state to a particular destination router.
In many use-cases a 'stable transport' IP Address is overloaded as an
identifier of a given node. Because the IP Prefixes may be re-
advertised into other levels there may be some ambiguity (e.g.
Originating router vs. L1L2 router) for which node a particular IP
prefix serves as identifier. The Prefix-SID Sub-TLV contains the
necessary flags to disambiguate IP Prefix to node mappings.
Furthermore if a given node has several 'stable transport' IP
addresses there are flags to differentiate those among other IP
Prefixes advertised from a given node.
A Prefix-SID Sub-TLV is associated to a prefix advertised by a node
and MAY be present in any of the following TLVs:
TLV-135 (IPv4) defined in [RFC5305].
Previdi, et al. Expires August 17, 2014 [Page 5]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
TLV-235 (MT-IPv4) defined in [RFC5120].
TLV-236 (IPv6) defined in [RFC5308].
TLV-237 (MT-IPv6) defined in [RFC5120].
The Index inside the Prefix-SID Sub-TLV MUST be preserved when an IP
Reachability TLV gets propagated across level boundaries.
The Prefix-SID Sub-TLV has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Flags | Algorithm |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SID/Index |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
where:
Type: 3
Length: variable.
Flags: 1 octet field of following flags:
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
|R|N|P| |
+-+-+-+-+-+-+-+-+
where:
R-Flag: Re-advertisement flag. If set, then the prefix to
which this Prefix-SID is attached, has been propagated by the
router either from another level (i.e.: from level-1 to level-2
or the opposite) or from redistribution (e.g.: from another
protocol).
N-Flag: Node-SID flag. Optional and, if set, then the Prefix-
SID refers to the router identified by the prefix. Typically,
the N-Flag is set on Prefix-SIDs attached to a router loopback
address. The N-Flag is set when the Prefix-SID is a Node-SID
as described in [I-D.filsfils-rtgwg-segment-routing].
Previdi, et al. Expires August 17, 2014 [Page 6]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
P-Flag: no-PHP flag. If set, then the penultimate hop MUST NOT
pop the Prefix-SID before delivering the packet to the node
that advertised the Prefix-SID.
Other bits: MUST be zero when originated and ignored when
received.
Algorithm: the router may use various algorithms when calculating
reachability to other nodes or to prefixes attached to these
nodes. Examples of these algorithms are metric based Shortest
Path First (SPF), various sorts of Constrained SPF, etc. The
Algorithm field allows a router to advertise algorithms that
router is currently using. SR-Algorithm TLV has following
structure: one octet identifying the algorithm to which the
Prefix-SID is associated. Currently, the following value has been
defined:
0: Shortest Path First (SPF) algorithm based on link metric.
Definitions and use of algorithms in Segment Routing are
described in [I-D.filsfils-rtgwg-segment-routing]
SID/Index: 32 bit index defining the offset in the SID/Label space
advertised by this router using the encodings defined in
Section 3.1.
Multiple Prefix-SIDs Sub-TLVs MAY appear on the same prefix in which
case each SID is encoded as a separate Sub-TLV. When multiple
Prefix-SID Sub-TLVs are present, the receiving router MUST use the
first encoded SID and MAY use the subsequent ones.
The No-PHP flag MUST be set on the Prefix-SIDs associated with
reachability advertisements which were originated by other routers
and leaked (either from Level-1 to Level-2 or vice versa).
The R-Flag MUST be set for prefixes that are not local to the router
and either:
advertised because of propagation (Level-1 into Level-2);
advertised because of leaking (Level-2 into Level-1);
advertised because redistribution (e.g.: from another protocol).
In the case where a Level-1-2 router has local interface addresses
configured in one level, it may also propagate these addresses into
the other level. In such case, the Level-1-2 router MUST NOT set the
R bit. The R-bit MUST be set only for prefixes that are not local to
Previdi, et al. Expires August 17, 2014 [Page 7]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
the router and advertised by the router because of propagation and/or
leaking.
The N-Flag is used in order to define a Node-SID. A router MAY set
the N-Flag only if all of the following conditions are met:
The prefix to which the Prefix-SID is attached is local to the
router. I.e.: the prefix is configured on one of the local
interfaces. (e.g.: 'stable transport' loopback).
The prefix to which the Prefix-SID is attached MUST have a Prefix
length of either /32 (IPv4) or /128 (IPv6).
The router MUST ignore the N-Flag on a received Prefix-SID if the
prefix has a Prefix length different than /32 (IPv4) or /128 (IPv6).
The router behavior determined by the P, R and N flags are described
in [I-D.filsfils-rtgwg-segment-routing].
2.3. Adjacency Segment Identifier
A new IS-IS Sub-TLV is defined: the Adjacency Segment Identifier Sub-
TLV (Adj-SID Sub-TLV).
The Adj-SID Sub-TLV is an optional Sub-TLV carrying the Segment
Routing IGP-Adjacency-SID as defined in
[I-D.filsfils-rtgwg-segment-routing] with flags and fields that may
be used, in future extensions of Segment Routing, for carrying other
types of SIDs.
IS-IS adjacencies are advertised using one of the IS-Neighbor TLVs
below:
TLV-22 [RFC5305]
TLV-222 [RFC5120]
TLV-23 [RFC5311]
TLV-223 [RFC5311]
TLV-141 [RFC5316]
Multiple Adj-SID Sub-TLVs MAY be associated with a single IS-
neighbor. Examples where more than one Adj-SID may be used per IS-
neighbor are described in
[I-D.filsfils-rtgwg-segment-routing-use-cases].
Previdi, et al. Expires August 17, 2014 [Page 8]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
2.3.1. Adjacency Segment Identifier (Adj-SID) Sub-TLV
The following format is defined for the Adj-SID Sub-TLV:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Flags | Weight |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SID/Label Sub-TLV (variable) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
where:
Type: 31
Length: variable.
Flags: 1 octet field of following flags:
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+
|F|B| |
+-+-+-+-+-+-+-+
where:
F-Flag: Address-Family flag. If unset, then the Adj-SID refers
to an adjacency with outgoing IPv4 encapsulation. If set then
the Adj-SID refers to an adjacency with outgoing IPv6
encapsulation.
B-Flag: Backup flag. If set, the Adj-SID refers to an
adjacency being protected (e.g.: using IPFRR or MPLS-FRR) as
described in [I-D.filsfils-rtgwg-segment-routing-use-cases].
Other bits: MUST be zero when originated and ignored when
received.
Weight: 1 octet. The value represents the weight of the Adj-SID
for the purpose of load balancing. The use of the weight is
defined in [I-D.filsfils-rtgwg-segment-routing].
SID/Label Sub-TLV: contains the SID/Label value as defined in
Section 2.1.
Previdi, et al. Expires August 17, 2014 [Page 9]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
An SR capable router MAY allocate an Adj-SID for each of its
adjacencies and SHOULD set the B-Flag when the adjacency is
protected by a FRR mechanism (IP or MPLS) as described in
[I-D.filsfils-rtgwg-segment-routing-use-cases].
The F-flag is used in order for the router to advertise the
outgoing encapsulation of the adjacency the Adj-SID is attached
to. Use cases of the use of the F-flag are described in
[I-D.filsfils-rtgwg-segment-routing-use-cases].
2.3.2. Adjacency Segment Identifiers in LANs
In LAN subnetworks, the Designated Intermediate System (DIS) is
elected and originates the Pseudonode-LSP (PN-LSP) including all
neighbors of the DIS.
When Segment Routing is used, each router in the LAN MAY advertise
the Adj-SID of each of its neighbors. Since, on LANs, each router
only advertises one adjacency to the DIS (and doesn't advertise any
other adjacency), each router advertises the set of Adj-SIDs (for
each of its neighbors) inside a newly defined Sub-TLV part of the TLV
advertising the adjacency to the DIS (e.g.: TLV-22).
The following new Sub-TLV is defined: LAN-Adj-SID (Type 32)
containing the set of Adj-SIDs the router assigned to each of its LAN
neighbors.
The format of the LAN-Adj-SID Sub-TLV is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Flags | Weight |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| System-ID (6 octets) |
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SID/Label Sub-TLV (variable) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
where:
Previdi, et al. Expires August 17, 2014 [Page 10]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
Type: 32
Length: variable.
Flags: 1 octet field of following flags:
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+
|F|B| |
+-+-+-+-+-+-+-+
where:
F-Flag: Address Family flag. If unset, then the Adj-SID refers
to an adjacency with outgoing IPv4 encapsulation. If set then
the Adj-SID refers to an adjacency with outgoing IPv6
encapsulation.
B-Flag: Backup flag. If set, the LAN-Adj-SID refers to an
adjacency being protected (e.g.: using IPFRR or MPLS-FRR) as
described in [I-D.filsfils-rtgwg-segment-routing-use-cases].
Other bits: MUST be zero when originated and ignored when
received.
Weight: 1 octet. The value represents the weight of the Adj-SID
for the purpose of load balancing. The use of the weight is
defined in [I-D.filsfils-rtgwg-segment-routing].
System-ID: 6 octets of IS-IS System-ID of length "ID Length" as
defined in [ISO10589].
SID/Label Sub-TLV: contains the SID/Label value as defined in
Section 2.1.
Multiple LAN-Adj-SID Sub-TLVs MAY be encoded.
In case one TLV-22/23/222/223 (reporting the adjacency to the DIS)
can't contain the whole set of LAN-Adj-SID Sub-TLVs, multiple
advertisements of the adjacency to the DIS MUST be used, MUST have
the same metric and SHOULD be inserted within the same LSP fragment.
Each router within the level, by receiving the DIS PN LSP as well as
the non-PN LSP of each router in the LAN, is capable of
reconstructing the LAN topology as well as the set of Adj-SID each
router uses for each of its neighbors.
Previdi, et al. Expires August 17, 2014 [Page 11]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
2.4. SID/Label Binding TLV
The SID/Label Binding TLV MAY be originated by any router in an IS-IS
domain. The router may advertise a SID/Label binding to a FEC along
with at least a single 'nexthop style' anchor. The protocol supports
more than one 'nexthop style' anchor to be attached to a SID/Label
binding, which results into a simple path description language. In
analogy to RSVP the terminology for this is called an 'Explicit Route
Object' (ERO). Since ERO style path notation allows to anchor SID/
label bindings to to both link and node IP addresses any label
switched path, can be described. Furthermore also SID/Label Bindings
from external protocols can get easily re-advertised.
The SID/Label Binding TLV may be used for advertising SID/Label
Bindings and their associated Primary and Backup paths. In one
single TLV either a primary ERO Path, a backup ERO Path or both are
advertised. If a router wants to advertise multiple parallel paths
then it can generate several TLVs for the same Prefix/FEC. Each
occurrence of a Binding TLV with respect with a given FEC Prefix has
accumulating and not canceling semantics. Due the space constraints
in the 8-Bit IS-IS TLVs an originating router MAY encode a primary
ERO path in one SID/Label Binding TLV and the backup ERO path in a
second SID/Label Binding TLV. Note that the FEC Prefix and SID/Label
Sub-TLV MUST be identical in both TLVs.
The SID/Label Binding TLV has type 149 and has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Flags | Weight |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Range | Prefix Length | FEC Prefix |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
// FEC Prefix (continued, variable) //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SubTLVs (variable) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: SID/Label Binding TLV format
o Type: 149
o Length: variable.
o 1 octet of flags
Previdi, et al. Expires August 17, 2014 [Page 12]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
o 1 octet of Weight
o 2 octets of Range
o 1 octet of Prefix Length
o 0-16 octets of FEC Prefix
o sub-TLVs, where each sub-TLV consists of a sequence of:
* 1 octet of sub-TLV type
* 1 octet of length of the value field of the sub-TLV
* 0-243 octets of value
2.4.1. Flags
Flags: 1 octet field of following flags:
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
|F|M| |
+-+-+-+-+-+-+-+-+
where:
F-Flag: Address Family flag. If unset, then the Prefix FEC
carries an IPv4 Prefix. If set then the Prefix FEC carries an
IPv6 Prefix.
M-Flag: Mirror Context flag. Set if the advertised SID/path
corresponds to a mirrored context. The use of the M flag is
described in [I-D.filsfils-rtgwg-segment-routing].
Other bits: MUST be zero when originated and ignored when
received.
2.4.2. Weight
Weight: 1 octet: The value represents the weight of the path for the
purpose of load balancing. The use of the weight is defined in
[I-D.filsfils-rtgwg-segment-routing].
2.4.3. Range
The 'Range' field provides the ability to specify a range of
addresses and their associated Prefix SIDs. It is essentially a
Previdi, et al. Expires August 17, 2014 [Page 13]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
compression scheme to distribute a continuous Prefix and their
continuous, corresponding SID/Label Block. If a single SID is
advertised then the range field MUST be set to one. For range
advertisements > 1, the number of addresses that need to be mapped
into a Prefix-SID and the starting value of the Prefix-SID range.
Example 1: if the following router addresses (loopback addresses)
need to be mapped into the corresponding Prefix SID indexes.
Router-A: 192.0.2.1/32, Prefix-SID: Index 1
Router-B: 192.0.2.2/32, Prefix-SID: Index 2
Router-C: 192.0.2.3/32, Prefix-SID: Index 3
Router-D: 192.0.2.4/32, Prefix-SID: Index 4
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |0|0| | Weight |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Range = 4 | /32 | 192 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| .0 | .2 | .1 | Sub-TLV Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sub-TLV Length| 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Example-2: If the following prefixes need to be mapped into the
corresponding Prefix-SID indexes:
10.1.1/24, Prefix-SID: Index 51
10.1.2/24, Prefix-SID: Index 52
10.1.3/24, Prefix-SID: Index 53
10.1.4/24, Prefix-SID: Index 54
10.1.5/24, Prefix-SID: Index 55
10.1.6/24, Prefix-SID: Index 56
10.1.7/24, Prefix-SID: Index 57
Previdi, et al. Expires August 17, 2014 [Page 14]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |0|0| | Weight |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Range = 7 | /24 | 10 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| .1 | .1 | Sub-TLV Type | Sub-TLV Length|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 51 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
It is not expected that a network operator will be able to keep fully
continuous FEC Prefix / SID/Index mappings. In order to support
noncontinuous mapping ranges an implementation MAY generate several
instances of Binding TLVs.
For example if a router wants to advertise the following ranges:
Range 16: { 192.168.1.1-15, Index 1-15 }
Range 6: { 192.168.1.22-27, Index 22-27 }
Range 41: { 192.168.1.44-84, Index 80-120 }
A router would need to advertise three instances of the Binding TLV.
2.4.4. Prefix Length, Prefix
The 'FEC Prefix' represents the Forwarding equivalence class at the
tail-end of the advertised path. The 'FEC Prefix' does not need to
correspond to a routable prefix of the originating node.
The 'Prefix Length' field contains the length of the prefix in bits.
Only the most significant octets of the Prefix FEC are encoded. I.e.
1 octet for FEC prefix length 1 up to 8, 2 octets for FEC prefix
length 9 to 16, 3 octets for FEC prefix length 17 up to 24 and 4
octets for FEC prefix length 25 up to 32, ...., 16 octets for FEC
prefix length 113 up to 128.
2.4.5. SID/Label Sub-TLV
The SID/Label Sub-TLV (Type 1) contains the SID/Label value as
defined in Section 2.1. It MUST be present in every SID/Label
Binding TLV.
Previdi, et al. Expires August 17, 2014 [Page 15]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
2.4.6. ERO Metric sub-TLV
ERO Metric sub-TLV (Type 2) is a Sub-TLV of the SID/Label Binding
TLV.
The ERO Metric sub-TLV carries the cost of an ERO path. It is used
to compare the cost of a given source/destination path. A router MAY
advertise the ERO Metric sub-TLV. The cost of the ERO Metric sub-TLV
SHOULD be set to the cumulative IGP or TE path cost of the advertised
ERO. Since manipulation of the Metric field may attract or distract
traffic from and to the advertised segment it MAY be manually
overridden.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Metric |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Metric (continued) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
ERO Metric sub-TLV format
where:
Type: 2
Length: 4
Metric: 4 bytes
2.4.7. IPv4 ERO subTLV
The IPv4 ERO subTLV (Type 3) describes a path segment using IPv4
address style of encoding. Its semantics have been borrowed from
[RFC3209].
The 'L' bit in the Flags is a one-bit attribute. If the L bit is
set, then the value of the attribute is 'loose.' Otherwise, the
value of the attribute is 'strict.'
Previdi, et al. Expires August 17, 2014 [Page 16]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |L| Reserved | IPv4 address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv4 address (continued) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: IPv4 ERO subTLV format
2.4.8. IPv6 ERO subTLV
The IPv6 ERO subTLV (Type 4) describes a path segment using IPv6
Address style of encoding. Its semantics have been borrowed from
[RFC3209].
The 'L' bit in the Flags is a one-bit attribute. If the L bit is
set, then the value of the attribute is 'loose.' Otherwise, the
value of the attribute is 'strict.'
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |L| Reserved | IPv6 address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv6 Address (continued) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv6 Address (continued) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv6 Address (continued) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv6 Address (continued) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: IPv6 ERO subTLV format
2.4.9. Unnumbered Interface ID ERO subTLV
The appearance and semantics of the 'Unnumbered Interface ID' have
been borrowed from Section 4 [RFC3477].
The Unnumbered Interface-ID ERO subTLV (Type 5) describes a path
segment that spans over an unnumbered interface. Unnumbered
interfaces are referenced using the interface index. Interface
indices are assigned local to the router and therefore not unique
within a domain. All elements in an ERO path need to be unique
within a domain and hence need to be disambiguated using a domain
unique Router-ID.
Previdi, et al. Expires August 17, 2014 [Page 17]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
The 'Router-ID' field contains the router ID of the router which has
assigned the 'Interface ID' field. Its purpose is to disambiguate
the 'Interface ID' field from other routers in the domain.
IS-IS supports two Router-ID formats:
o (TLV 134, 32-Bit format) [RFC5305]
o (TLV 140, 128-Bit format) [RFC6119]
The actual Router-ID format gets derived from the 'Length' field.
o For 32-Bit Router-ID width the subTLV length is set to 8 octets.
o For 128-Bit Router-ID width the subTLV length is set to 20 octets.
The 'Interface ID' is the identifier assigned to the link by the
router specified by the router ID.
The 'L' bit in the Flags is a one-bit attribute. If the L bit is
set, then the value of the attribute is 'loose.' Otherwise, the
value of the attribute is 'strict.'
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |L| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
// Router ID (32 or 128 bits) //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Interface ID (32 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4: Unnumbered Interface ID ERO subTLV format
2.4.10. IPv4 Backup ERO subTLV
The IPv4 Backup ERO subTLV (Type 6) describes a Backup path segment
using IPv4 Address style of encoding. Its appearance and semantics
have been borrowed from [RFC3209].
The 'L' bit in the Flags is a one-bit attribute. If the L bit is
set, then the value of the attribute is 'loose.' Otherwise, the
value of the attribute is 'strict.'
Previdi, et al. Expires August 17, 2014 [Page 18]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |L| Reserved | IPv4 address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv4 address (continued) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5: IPv4 Backup ERO subTLV format
2.4.11. IPv6 Backup ERO subTLV
The IPv6 Backup ERO subTLV (Type 7) describes a Backup path segment
using IPv6 Address style of encoding. Its appearance and semantics
have been borrowed from [RFC3209].
The 'L' bit in the Flags is a one-bit attribute. If the L bit is
set, then the value of the attribute is 'loose.' Otherwise, the
value of the attribute is 'strict.'
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |L| Reserved | IPv6 address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv6 Address (continued) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv6 Address (continued) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv6 Address (continued) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv6 Address (continued) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6: IPv6 Backup ERO subTLV format
2.4.12. Unnumbered Interface ID Backup ERO subTLV
The appearance and semantics of the 'Unnumbered Interface ID' have
been borrowed from Section 4 [RFC3477].
The Unnumbered Interface-ID Backup ERO subTLV (Type 8) describes a
Backup LSP path segment that spans over an unnumbered interface.
Unnumbered interfaces are referenced using the interface index.
Interface indices are assigned local to the router and therefore not
unique within a domain. All elements in an ERO path need to be
unique within a domain and hence need to be disambiguated using a
domain unique Router-ID.
Previdi, et al. Expires August 17, 2014 [Page 19]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
The 'Router-ID' field contains the router ID of the router which has
assigned the 'Interface ID' field. Its purpose is to disambiguate
the 'Interface ID' field from other routers in the domain.
IS-IS supports two Router-ID formats:
o (TLV 134, 32-Bit format) [RFC5305]
o (TLV 140, 128-Bit format) [RFC6119]
The actual Router-ID format gets derived from the 'Length' field.
o For 32-Bit Router-ID width the subTLV length is set to 8 octets.
o For 128-Bit Router-ID width the subTLV length is set to 20 octets.
The 'Interface ID' is the identifier assigned to the link by the
router specified by the router ID.
The 'L' bit in the Flags is a one-bit attribute. If the L bit is
set, then the value of the attribute is 'loose.' Otherwise, the
value of the attribute is 'strict.'
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |L| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
// Router ID (32 or 128 bits) //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Interface ID (32 bits) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 7: Unnumbered Interface ID Backup ERO subTLV format
2.4.13. Prefix ERO and Prefix Backup ERO subTLV path semantics
All 'ERO' and 'Backup ERO' information represents an ordered set
which describes the segments of a path. The last ERO subTLV
describes the segment closest to the egress point of the path.
Contrary the first ERO subTLV describes the first segment of a path.
If a router extends or stitches a label switched path it MUST prepend
the new segments path information to the ERO list. The same ordering
applies for the Backup ERO labels. An implementation SHOULD first
encode all primary path EROs followed by the bypass EROs.
Previdi, et al. Expires August 17, 2014 [Page 20]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
3. Router Capabilities
3.1. SR-Capabilities Sub-TLV
Segment Routing requires each router to advertise its SR data-plane
capability and the range of SID/Label values it uses for Segment
Routing. Data-plane capabilities and SID/Label ranges are advertised
using the newly defined SR-Capabilities Sub-TLV inserted into the
IS-IS Router Capability TLV-242 that is defined in [RFC4971].
The Router Capability TLV specifies flags that control its
advertisement. The SR Capabilities Sub-TLV MUST be propagated
throughout the level and need not to be advertised across level
boundaries. Therefore Router Capability TLV distribution flags MUST
be set accordingly, i.e.: the S flag MUST be unset.
The SR Capabilities Sub-TLV (Type 2) is optional, MAY appear multiple
times inside the Router Capability TLV and has following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Flags | Range |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Range (cont.) | SID/Label Sub-TLV (variable) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
where:
Type: 2
Length: variable.
Flags: 1 octet of flags. The following are defined:
0
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
|I|V| |
+-+-+-+-+-+-+-+-+
where:
I-Flag: IPv4 flag. If set, then the router is capable of
outgoing IPv4 encapsulation on all interfaces.
Previdi, et al. Expires August 17, 2014 [Page 21]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
V-Flag: IPv6 flag. If set, then the router is capable of
outgoing IPv6 encapsulation on all interfaces.
Range: 3 octets value defining the number of values of the range
from the starting value defined in the SID/Label Sub-TLV.
SID/Label Sub-TLV: SID/Label value as defined in Section 2.1.
If multiple occurrence of the SR-Capabilities Sub-TLV are advertised
by the same router, only the Flags in the first occurrence of the
Sub-TLV are to be taken into account.
3.2. SR-Algorithm Sub-TLV
The router may use various algorithms when calculating reachability
to other nodes or to prefixes attached to these nodes. Examples of
these algorithms are metric based Shortest Path First (SPF), various
sorts of Constrained SPF, etc. The SR-Algorithm Sub-TLV (Type 15)
allows the router to advertise the algorithms that the router is
currently using. The following value has been defined:
0: Shortest Path First (SPF) algorithm based on link metric.
The SR-Algorithm Sub-TLV is inserted into the IS-IS Router Capability
TLV-242 that is defined in [RFC4971].
The Router Capability TLV specifies flags that control its
advertisement. The SR-Algorithm MUST be propagated throughout the
level and need not to be advertised across level boundaries.
Therefore Router Capability TLV distribution flags MUST be set
accordingly, i.e.: the S flag MUST be unset.
The SR-Algorithm Sub-TLV is optional, it MAY only appear a single
time inside the Router Capability TLV. If the SID-Label Capability
Sub-TLV is advertised then the SR-Algorithm Sub-TLV MUST also be
advertised.
It has following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Algorithm 1 | Algorithm 2 | Algorithm ... | Algorithm n |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
where:
Previdi, et al. Expires August 17, 2014 [Page 22]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
Type: 15
Length: variable.
Algorithm: 1 octet of algorithm Section 2.2
4. IANA Considerations
This documents request allocation for the following TLVs and subTLVs.
+-----+--------------+-------------+---------+---------+------------+
| PDU | TLV | subTLV | Type | subType | #Occurence |
+-----+--------------+-------------+---------+---------+------------+
| LSP | IS Neighbor | | 22, 23, | | >=0 |
| | | | 222, | | |
| | | | 223 | | |
| | | SID/Label | | 31 | >0 |
| | | LAN | | 32 | >0 |
| | | SID/Label | | | |
| LSP | IP | | 135, | | >=0 |
| | reachability | | 235, | | |
| | | | 236, | | |
| | | | 237 | | |
| | | SID/Label | | 3 | >0 |
| LSP | SID/MPLS | | 149 | | >=0 |
| | Binding | | | | |
| | | SID/Label | | 1 | >0 |
| | | ERO Metric | | 2 | 1 |
| | | IPv4 ERO | | 3 | >=0 |
| | | IPv6 ERO | | 4 | >=0 |
| | | Unnumbered | | 5 | >=0 |
| | | Interface | | | |
| | | ID ERO | | | |
| | | IPv4 Backup | | 6 | >=0 |
| | | ERO | | | |
| | | IPv6 Backup | | 7 | >=0 |
| | | ERO | | | |
| | | Unnumbered | | 8 | >=0 |
| | | Interface | | | |
| | | ID Backup | | | |
| | | ERO | | | |
| LSP | Router | | 242 | | >=0 |
| | Capability | | | | |
| | | SR | | 2 | >=0 |
| | | Capability | | | |
Previdi, et al. Expires August 17, 2014 [Page 23]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
| | | SR | | 15 | 1 |
| | | Algorithm | | | |
+-----+--------------+-------------+---------+---------+------------+
Table 1: IANA allocations
The SID/MPLS Binding TLV requires a new sub-registry. Type value 149
has been assigned, with a starting sub-TLV value of 1, range from
1-255, and managed by Expert Review.
5. Manageability Considerations
TBD
6. Security Considerations
TBD
7. Contributors
The following people gave a substantial contribution to the content
of this document: Martin Horneffer, Bruno Decraene, Igor Milojevic,
Rob Shakir, Saku Ytti, Wim Henderickx, Jeff Tantsura, Les Ginsberg
and Steven Luong.
8. Acknowledgements
We would like to thank Dave Ward, Dan Frost, Stewart Bryant and
Pierre Francois for their contribution to the content of this
document.
Many thanks to Yakov Rekhter and Ina Minei for their contribution on
earlier incarnations of the "Binding / MPLS Label TLV" in
[I-D.gredler-isis-label-advertisement].
9. References
9.1. Normative References
[ISO10589]
International Organization for Standardization,
"Intermediate system to Intermediate system intra-domain
routeing information exchange protocol for use in
Previdi, et al. Expires August 17, 2014 [Page 24]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
conjunction with the protocol for providing the
connectionless-mode Network Service (ISO 8473)", ISO/
IEC 10589:2002, Second Edition, Nov 2002.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
Tunnels", RFC 3209, December 2001.
[RFC3477] Kompella, K. and Y. Rekhter, "Signalling Unnumbered Links
in Resource ReSerVation Protocol - Traffic Engineering
(RSVP-TE)", RFC 3477, January 2003.
[RFC4971] Vasseur, JP., Shen, N., and R. Aggarwal, "Intermediate
System to Intermediate System (IS-IS) Extensions for
Advertising Router Information", RFC 4971, July 2007.
[RFC5120] Przygienda, T., Shen, N., and N. Sheth, "M-ISIS: Multi
Topology (MT) Routing in Intermediate System to
Intermediate Systems (IS-ISs)", RFC 5120, February 2008.
[RFC5305] Li, T. and H. Smit, "IS-IS Extensions for Traffic
Engineering", RFC 5305, October 2008.
[RFC5308] Hopps, C., "Routing IPv6 with IS-IS", RFC 5308,
October 2008.
[RFC5311] McPherson, D., Ginsberg, L., Previdi, S., and M. Shand,
"Simplified Extension of Link State PDU (LSP) Space for
IS-IS", RFC 5311, February 2009.
[RFC5316] Chen, M., Zhang, R., and X. Duan, "ISIS Extensions in
Support of Inter-Autonomous System (AS) MPLS and GMPLS
Traffic Engineering", RFC 5316, December 2008.
[RFC6119] Harrison, J., Berger, J., and M. Bartlett, "IPv6 Traffic
Engineering in IS-IS", RFC 6119, February 2011.
9.2. Informative References
[I-D.filsfils-rtgwg-segment-routing]
Filsfils, C., Previdi, S., Bashandy, A., Decraene, B.,
Litkowski, S., Horneffer, M., Milojevic, I., Shakir, R.,
Ytti, S., Henderickx, W., Tantsura, J., and E. Crabbe,
"Segment Routing Architecture",
draft-filsfils-rtgwg-segment-routing-01 (work in
Previdi, et al. Expires August 17, 2014 [Page 25]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
progress), October 2013.
[I-D.filsfils-rtgwg-segment-routing-use-cases]
Filsfils, C., Francois, P., Previdi, S., Decraene, B.,
Litkowski, S., Horneffer, M., Milojevic, I., Shakir, R.,
Ytti, S., Henderickx, W., Tantsura, J., Kini, S., and E.
Crabbe, "Segment Routing Use Cases",
draft-filsfils-rtgwg-segment-routing-use-cases-02 (work in
progress), October 2013.
[I-D.gredler-isis-label-advertisement]
Gredler, H., Amante, S., Scholl, T., and L. Jalil,
"Advertising MPLS labels in IS-IS",
draft-gredler-isis-label-advertisement-03 (work in
progress), May 2013.
Authors' Addresses
Stefano Previdi (editor)
Cisco Systems, Inc.
Via Del Serafico, 200
Rome 00142
Italy
Email: sprevidi@cisco.com
Clarence Filsfils
Cisco Systems, Inc.
Brussels,
BE
Email: cfilsfil@cisco.com
Ahmed Bashandy
Cisco Systems, Inc.
170, West Tasman Drive
San Jose, CA 95134
US
Email: bashandy@cisco.com
Previdi, et al. Expires August 17, 2014 [Page 26]
Internet-Draft IS-IS Extensions for Segment Routing February 2014
Hannes Gredler
Juniper Networks, Inc.
1194 N. Mathilda Ave.
Sunnyvale, CA 94089
US
Email: hannes@juniper.net
Stephane Litkowski
Orange
FR
Email: stephane.litkowski@orange.com
Jeff Tantsura
Ericsson
300 Holger Way
San Jose, CA 95134
US
Email: Jeff.Tantsura@ericsson.com
Previdi, et al. Expires August 17, 2014 [Page 27]