Internet DRAFT - draft-rekhter-mpls-pim-sm-over-mldp
draft-rekhter-mpls-pim-sm-over-mldp
Network Working Group Yakov Rekhter
Internet Draft Juniper Networks
Intended status: Standards Track
Expires: August 2014 Rahul Aggarwal
Arktan
Nicolai Leymann
Deutsche Telekom
Wim Henderickx
Alcatel-Lucent
Quintin Zhao
Huawei
Richard Li
Huawei
February 7 2014
Carrying PIM-SM in ASM mode Trees over P2MP mLDP LSPs
draft-rekhter-mpls-pim-sm-over-mldp-08.txt
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that other
groups may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Rekhter [Page 1]
Internet Draft draft-rekhter-mpls-pim-sm-over-mldp-08.txt February 2014
Copyright Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Abstract
When IP multicast trees created by PIM-SM in Any Source Multicast
(ASM) mode need to pass through an MPLS domain, it may be desirable
to map such trees to Point-to-Multipoint Label Switched Paths. This
document describes how to accomplish this in the case where such
Point-to-Multipoint Label Switched Paths are established using mLDP.
Rekhter [Page 2]
Internet Draft draft-rekhter-mpls-pim-sm-over-mldp-08.txt February 2014
Table of Contents
1 Specification of Requirements ......................... 3
2 Introduction .......................................... 3
3 Option 1 - Non-transitive mapping of IP multicast shared tree 5
3.1 Originating Source Active auto-discovery routes (Option 1) 5
3.2 Receiving BGP Source Active auto-discovery route by LSR ...6
3.3 Handling (S, G, RPT-bit) state ........................ 6
4 Option 2 - Transitive mapping of IP multicast shared tree .6
4.1 In-band signaling for IP Multicast Shared Tree ........ 7
4.2 Originating Source Active auto-discovery routes (Option 2) 8
4.3 Receiving BGP Source Active auto-discovery route ...... 9
4.4 Pruning Sources off the Shared Tree ................... 9
4.5 More on handling (S,G,RPT-bit) state .................. 10
5 IANA Considerations ................................... 10
6 Security Considerations ............................... 10
7 Acknowledgements ...................................... 10
8 Normative References .................................. 11
9 Informative References ................................ 11
10 Authors' Addresses .................................... 11
1. Specification of Requirements
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. Introduction
[RFC6826] describes how to map Point-to-Multipoint Label Switched
Paths (P2MP LSPs) created by mLDP [mLDP] to multicast trees created
by PIM-SM in SSM mode [RFC4607]. This document describes how to map
mLDP P2MP trees to multicast trees created by PIM-SM in ASM mode. It
describes two possible options for doing this.
An implementation MAY support Option 1, as described in Section 3 of
this document. An implementation MUST support Option 2, as described
Rekhter [Page 3]
Internet Draft draft-rekhter-mpls-pim-sm-over-mldp-08.txt February 2014
in Section 4 of this document.
Note that from a deployment point of view these two options are
mutually exclusive. That is on the same network one could either
deploy Option 1, or Option 2, but not both.
The reader of this document is expected to be familiar with PIM-SM
[RFC4601] and mLDP [mLDP].
This document relies on the procedures in [RFC6826] to support Source
Trees. E.g., following these procedures an LSR may initiate a mLDP
Label Map with the Transit IPv4/IPv6 Source TLV for (S, G) when
receiving PIM (S,G) Join.
This document uses BGP Source Active auto-discovery routes, as
defined in [MVPN-BGP].
In a deployment scenario where the service provider has provisioned
the network in such a way that the RP for a particular ASM group G is
always between the receivers and the sources. If the network is
provisioned in this manner, the ingress PE for (S,G) is always the
same as the ingress PE for the RP, and thus the Source Active A-D
routes are never needed. If it is known a priori that the network is
provisioned in this manner, mLDP in-band signaling can be supported
using a different set of procedures, as specified in [draft-
wijnands]. A service provider will provision the PE routers either
to use [draft-wijnands] procedures or to use the procedures of this
document.
Like [RFC6826], each IP multicast tree is mapped one-to-one to a P2MP
LSP in the MPLS network. This type of service works well if the
number of LSPs that are created is under control of the MPLS network
operator, or if the number of LSPs for a particular service are known
to be limited in number.
It is to be noted that the existing BGP MVPN [MVPN-BGP] procedures
may be used to map Internet IP multicast trees to P2MP LSPs. These
procedures would accomplish this for IP multicast trees created by
PIM-SM in SSM mode as well as for IP multicast trees created by PIM-
SM in ASM mode. Furthermore, these procedures would also support the
ability to aggregate multiple IP multicast trees to one P2MP LSP in
the MPLS network. The details of this particular approach are out of
scope of this document.
This document assumes that a given LSR may have some of its
interfaces IP multicast capable, while other interfaces being MPLS
Rekhter [Page 4]
Internet Draft draft-rekhter-mpls-pim-sm-over-mldp-08.txt February 2014
capable.
3. Option 1 - Non-transitive mapping of IP multicast shared tree
This option does not transit IP multicast shared trees over the MPLS
network. Therefore, when an LSR creates (*, G) state (as a result of
receiving PIM messages on one of its IP multicast interfaces), the
LSR does not propagate this state in mLDP.
3.1. Originating Source Active auto-discovery routes (Option 1)
Whenever (as a result of receiving either PIM Register or MSDP
messages) a Rendezvous Point (RP) discovers a new multicast source,
the RP SHOULD originate a BGP Source Active auto-discovery route.
The route carries a single MCAST-VPN NLRI [MVPN-BGP] constructed as
follows:
+ The Route Distinguisher (RD) in this NLRI is set to 0.
+ The Multicast Source field MUST be set to S. This could be either
an IPv4 or an IPv6 address. The Multicast Source Length field is
set appropriately to reflect this.
+ The Multicast Group field MUST be set to G. This could be either
an IPv4 or an IPv6 address. The Multicast Group Length field is
set appropriately to reflect this.
To constrain distribution of the Source Active auto-discovery route
to the AS of the advertising RP this route SHOULD carry the NO_EXPORT
Community ([RFC1997]).
Using the normal BGP procedures the Source Active auto-discovery
route is propagated to all other LSRs within the AS.
Whenever the RP discovers that the source is no longer active, the RP
MUST withdraw the Source Active auto-discovery route, if such a route
was previously advertised by the RP.
Rekhter [Page 5]
Internet Draft draft-rekhter-mpls-pim-sm-over-mldp-08.txt February 2014
3.2. Receiving BGP Source Active auto-discovery route by LSR
Consider an LSR that has some of its interfaces capable of IP
multicast and some capable of MPLS multicast.
When as a result of receiving PIM messages on one of its IP multicast
interfaces such LSR creates in its Tree Information Base (TIB) a new
(*, G) entry with a non-empty outgoing interface list that contains
one or more IP multicast interfaces, the LSR MUST check if it has any
Source Active auto-discovery routes for that G. If there is such a
route, S of that route is reachable via an MPLS interface, and the
LSR does not have (S, G) state in its TIB for (S, G) carried in the
route, then the LSR originates the mLDP Label Map with the Transit
IPv4/IPv6 Source TLV carrying (S,G), as specified in [RFC6826].
When an LSR receives a new Source Active auto-discovery route, the
LSR MUST check if its TIB contains an (*, G) entry with the same G as
carried in the Source Active auto-discovery route. If such an entry
is found, S is reachable via an MPLS interface, and the LSR does not
have (S, G) state in its TIB for (S, G) carried in the route, then
the LSR originates an mLDP Label Map with the Transit IPv4/IPv6
Source TLV carrying (S,G), as specified in [RFC6826].
3.3. Handling (S, G, RPT-bit) state
Creation and deletion of (S, G, RPT-bit) PIM state ([RFC4601]) on a
LSR that resulted from receiving PIM messages on one of its IP
multicast interfaces does not result in any mLDP and/or BGP actions
by the LSR.
4. Option 2 - Transitive mapping of IP multicast shared tree
This option enables transit of IP multicast shared trees over the
MPLS network. Therefore, when an LSR creates (*, G) state as a result
of receiving PIM messages on one of its IP multicast interfaces, the
LSR does propagate this state in mLDP, as described below.
Note that in the deployment scenarios where for a given G none of the
PEs originate an (S, G) mLDP Label Map with the Transit IPv4/IPv6
Source TLV, no Source Active auto-discovery routes will be used. One
other scenario where no Source Active auto-discovery routes will be
used is described in section "Originating Source Active auto-
discovery routes (Option 2)". In all these scenarios the only part of
Option 2 that will be used is the in-band signaling for IP Multicast
Shared Tree, as described in the next section.
Rekhter [Page 6]
Internet Draft draft-rekhter-mpls-pim-sm-over-mldp-08.txt February 2014
4.1. In-band signaling for IP Multicast Shared Tree
To provide support for in-band mLDP signaling of IP multicast shared
trees this document defines two new mLDP TLVs: Transit IPv4 Shared
Tree TLV, and Transit IPv6 Shared Tree TLV.
These two TLVs have exactly the same encoding/format as the IPv4/IPv6
Source Tree TLVs defined in [RFC6826], except that instead of the
Source field they have the RP field, and this field carries the
address of the RP, as follows:
Transit IPv4 Shared Tree TLV:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | RP
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Group
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type: TBD (to be assigned by IANA).
Length: 8
RP: IPv4 RP address, 4 octets.
Group: IPv4 multicast group address, 4 octets.
Transit IPv6 Shared Tree TLV:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | RP ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ | Group ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type: TBD (to be assigned by IANA).
Rekhter [Page 7]
Internet Draft draft-rekhter-mpls-pim-sm-over-mldp-08.txt February 2014
Length: 32
RP: IPv6 RP address, 16 octets.
Group: IPv6 multicast group address, 16 octets.
Procedures for in-band signaling for IP multicast shared trees with
mLDP follow the same procedures as for in-band signaling for IP
multicast source trees specified in [RFC6826], except that while the
latter signals (S,G) state using Transit IPv4/IPv6 Source TLVs, the
former signals (*,G) state using Transit IPv4/IPv6 Shared Tree TLVs.
4.2. Originating Source Active auto-discovery routes (Option 2)
Consider an LSR that has some of its interfaces capable of IP
multicast and some capable of MPLS multicast.
Whenever such LSR creates an (S, G) state as a result of receiving an
mLDP Label Map with the Transit IPv4/IPv6 Source TLV for (S, G), if
all of the following are true:
+ S is reachable via one of the IP multicast capable interfaces,
+ the LSR determines that G is in the PIM-SM in ASM mode range, and
+ the LSR does not have an (*, G) state with one of the IP
multicast capable interfaces as an incoming interface (iif) for
that state
the LSR MUST originate a BGP Source Active auto-discovery route.
The route carries a single MCAST-VPN NLRI constructed as follows:
+ The RD in this NLRI is set to 0.
+ The Multicast Source field MUST be set to S. The Multicast Source
Length field is set appropriately to reflect this.
+ The Multicast Group field MUST be set to G. The Multicast Group
Length field is set appropriately to reflect this.
To constrain distribution of the Source Active auto-discovery route
to the AS of the advertising LSR this route SHOULD carry the
Rekhter [Page 8]
Internet Draft draft-rekhter-mpls-pim-sm-over-mldp-08.txt February 2014
NO_EXPORT Community ([RFC1997]).
Using the normal BGP procedures the Source Active auto-discovery
route is propagated to all other LSRs within the AS.
Whenever the LSR deletes the (S,G) state that was previously created
as a result of receiving an mLDP Label Map with the Transit IPv4/IPv6
Source TLV for (S,G), the LSR that deletes the state MUST also
withdraw the Source Active auto-discovery route, if such a route was
advertised when the state was created.
Note that whenever an LSR creates an (S,G) state as a result of
receiving an mLDP Label Map with the Transit IPv4/IPv6 Source TLV for
(S,G) with S reachable via one of the IP multicast capable
interfaces, and the LSR already has a (*,G) state with RP reachable
via one of the IP multicast capable interfaces as a result of
receiving an mLDP Label Map with the Transit IPv4/IPv6 Shared Tree
TLV for (*,G), the LSR does not originate a Source Active auto-
discovery route.
4.3. Receiving BGP Source Active auto-discovery route
Procedures for receiving BGP Source Active auto-discovery routes are
the same as with Option 1.
4.4. Pruning Sources off the Shared Tree
If after receiving a new Source Active auto-discovery route for (S,G)
the LSR determines that (a) it has the (*, G) entry in its TIB, (b)
the incoming interface list (iif) for that entry contains one of the
IP interfaces, (c) at least one of the MPLS interfaces is in the
outgoing interface list (oif) for that entry, and (d) the LSR does
not originate an mLDP Label Mapping message for (S,G) with the
Transit IPv4/IPv6 Source TLV, then the LSR MUST transition the
(S,G,RPT-bit) downstream state to the Prune state. [Conceptually the
PIM state machine on the LSR will act "as if" it had received
Prune(S,G,rpt) on one of its MPLS interfaces, without actually having
received one.] Depending on the (S,G,RPT-bit) state on the iif, this
may result in the LSR using PIM procedures to prune S off the Shared
(*,G) tree.
The LSR MUST keep the (S,G,RPT-bit) downstream state machine in the
Prune state for as long as (a) the outgoing interface list (oif) for
(*, G) contains one of the MPLS interfaces, and (b) the LSR has at
least one Source Active auto-discovery route for (S,G), and (c) the
LSR does not originate the mLDP Label Mapping message for (S,G) with
Rekhter [Page 9]
Internet Draft draft-rekhter-mpls-pim-sm-over-mldp-08.txt February 2014
the Transit IPv4/IPv6 Source TLV. Once either of these conditions
become no longer valid, the LSR MUST transition the (S,G,RPT-bit)
downstream state machine to the NoInfo state.
Note that except for the scenario described in the first paragraph of
this section, in all other scenarios relying solely on PIM procedures
on the LSR is sufficient to ensure the correct behavior when pruning
sources off the shared tree.
4.5. More on handling (S,G,RPT-bit) state
Creation and deletion of (S,G,RPT-bit) state on a LSR that resulted
from receiving PIM messages on one of its IP multicast interfaces
does not result in any mLDP and/or BGP actions by the LSR.
5. IANA Considerations
This document requires allocation from the LDP MP Opaque Value
Element type name space managed by IANA the following two new mLDP
TLVs: Transit IPv4 Shared Tree TLV, and Transit IPv6 Shared Tree TLV.
6. Security Considerations
All the security considerations for mLDP ([mLDP]) apply here.
7. Acknowledgements
Use of Source Active auto-discovery routes was borrowed from [MVPN-
BGP]. Some text in this document was borrowed from [MVPN-BGP].
Some of the text in this document was borrowed from [RFC6826].
We would like to acknowledge Arkadiy Gulko for his review and
comments.
We would also like to thank Xuxiaohu, Gregory Mirsky, and Rajiv Asati
for their review and comments.
Rekhter [Page 10]
Internet Draft draft-rekhter-mpls-pim-sm-over-mldp-08.txt February 2014
8. Normative References
[mLDP] Minei, I., "Label Distribution Protocol Extensions for Point-
to- Multipoint and Multipoint-to-Multipoint Label Switched Paths",
RFC6388, November 2011.
[RFC6826] "In-band signaling for Point-to-Multipoint and Multipoint-
to-Multipoint Label Switched Paths", I. Wijnands et al., RFC6826,
January 2013
[MVPN-BGP] "BGP Encodings and Procedures for Multicast in MPLS/BGP IP
VPNs", R. Aggarwal et al., RFC6514, February 2012
[RFC1997] R. Chandra, P. Traina, T. Li, "BGP Communities Attribute",
RFC1997, August 1996.
[RFC2119] "Key words for use in RFCs to Indicate Requirement
Levels.", Bradner, RFC2119, March 1997.
9. Informative References
[RFC4601] Fenner, B., Handley, M., Holbrook, H., and I. Kouvelas,
"Protocol Independent Multicast - Sparse Mode (PIM-SM): Protocol
Specification (Revised)", RFC 4601, August 2006.
[RFC4607] Holbrook, H. and B. Cain, "Source-Specific Multicast for
IP", RFC 4607, August 2006.
[draft-wijnands] Wijnands IJ, et. al., "mLDP In-Band Signaling with
Wildcards", draft-wijnands-mpls-mldp-in-band-wildcard-encoding, work
in progress
10. Authors' Addresses
Yakov Rekhter
Juniper Networks, Inc.
e-mail: yakov@juniper.net
Rahul Aggarwal
e-mail: raggarwa_1@yahoo.com
Nicolai Leymann
Deutsche Telekom
Winterfeldtstrasse 21
Berlin 10781
Rekhter [Page 11]
Internet Draft draft-rekhter-mpls-pim-sm-over-mldp-08.txt February 2014
Germany
e-mail: nicolai.leymann@t-systems.com
Wim Henderickx
Alcatel-Lucent
Email: wim.henderickx@alcatel-lucent.com
Richard Li
Huawei
Email: renwei.li@huawei.com
Quintin Zhao
Huawei
Email: quintin.zhao@huawei.com
Rekhter [Page 12]