Internet DRAFT - draft-rtgwg-bgp-pic
draft-rtgwg-bgp-pic
Network Working Group A. Bashandy, Ed.
Internet Draft C. Filsfils
Intended status: Informational Cisco Systems
Expires: April 2014 P. Mohapatra
Cumulus Networks
October 21, 2013
BGP Prefix Independent Convergence
draft-rtgwg-bgp-pic-02.txt
Abstract
In the network comprising thousands of iBGP peers exchanging millions
of routes, many routes are reachable via more than one path. Given
the large scaling targets, it is desirable to restore traffic after
failure in a time period that does not depend on the number of BGP
prefixes. In this document we proposed a technique by which traffic
can be re-routed to ECMP or pre-calculated backup paths in a
timeframe that does not depend on the number of BGP prefixes. The
objective is achieved through organizing the forwarding chains in a
hierarchical manner and sharing forwarding elements among the maximum
possible number of routes. The proposed technique achieves prefix
independent convergence while ensuring incremental deployment,
complete transparency and automation, and zero management and
provisioning effort
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s)
controlling the copyright in such materials, this document may not
be modified outside the IETF Standards Process, and derivative
works of it may not be created outside the IETF Standards Process,
except to format it for publication as an RFC or to translate it
into languages other than English.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
Bashandy Expires April 21, 2014 [Page 1]
Internet-Draft BGP Prefix Independent Convergence October 2013
documents at any time. It is inappropriate to use Internet-Drafts
as reference material or to cite them other than as "work in
progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
This Internet-Draft will expire on September 21, 2013.
Copyright Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with
respect to this document. Code Components extracted from this
document must include Simplified BSD License text as described in
Section 4.e of the Trust Legal Provisions and are provided without
warranty as described in the Simplified BSD License.
Table of Contents
1. Introduction...................................................3
1.1. Conventions used in this document.........................3
1.2. Terminology...............................................4
2. Constructing the Shared Hierarchical Forwarding Chain..........5
2.1. Databases.................................................5
2.2. Constructing the forwarding chain from a downloaded route.6
2.3. Examples..................................................7
2.3.1. Example 1: Forwarding Chain for iBGP ECMP............7
2.3.2. Example 2: Primary Backup Paths......................9
3. Forwarding Behavior...........................................10
4. Forwarding Chain Adjustment at a Failure......................10
4.1. BGP-PIC core.............................................11
4.2. BGP-PIC edge.............................................12
4.2.1. Adjusting forwarding Chain in egress node failure...12
4.2.2. Adjusting Forwarding Chain on PE-CE link Failure....12
4.2.3. Loop Avoidance using Special Label (backup/repair
label).....................................................13
5. Properties....................................................14
6. Dependency....................................................17
Bashandy Expires April 21, 2014 [Page 2]
Internet-Draft BGP Prefix Independent Convergence October 2013
7. Security Considerations.......................................18
8. IANA Considerations...........................................18
9. Conclusions...................................................18
10. References...................................................18
10.1. Normative References....................................18
10.2. Informative References..................................18
11. Acknowledgments..............................................19
Appendix A. Modification History.................................20
A.1.1. Changes from Version 01.............................20
A.1.2. Changes from Version 00.............................20
1. Introduction
As a path vector protocol, BGP is inherently slow due to the
serial nature of reachability propagation. BGP speakers exchange
reachability information about prefixes[2][3] and, for labeled
address families, namely AFI/SAFI 1/4, 2/4, 1/128, and 2/128, an
edge router assigns local labels to prefixes and associates the
local label with each advertised prefix such as L3VPN [6], 6PE
[7], and Softwire [5]. A BGP speaker then applies the path
selection steps to choose the best path. In modern networks, it is
not uncommon to have a prefix reachable via multiple edge routers.
In addition to proprietary techniques, multiple techniques have
been proposed to allow for more than one path for a given prefix
[4][9][10], whether in the form of equal cost multipath or
primary-backup. Another more common and widely deployed scenario
is L3VPN with multi-homed VPN sites.
This document proposes a hierarchical and shared forwarding chain
organization that allows traffic to be restored to pre-calculated
alternative equal cost primary path or backup path in a time
period that does not depend on the number of BGP prefixes. The
technique relies on internal router behavior that is completely
transparent to the operator and can be incrementally deployed and
enabled with zero operator intervention.
1.1. Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL"
in this document are to be interpreted as described in RFC-2119
[1].
In this document, these words will appear with that interpretation
only when in ALL CAPS. Lower case uses of these words are not to
be interpreted as carrying RFC-2119 significance.
Bashandy Expires April 21, 2014 [Page 3]
Internet-Draft BGP Prefix Independent Convergence October 2013
1.2. Terminology
This section defines the terms used in this document. For ease of
use, we will use terms similar to those used by L3VPN [6]
o BGP prefix: It is a prefix P/m (of any AFI/SAFI) that a BGP
speaker has a path for.
o IGP prefix: It is a prefix P/m (of any AFI/SAFI) that is learnt
via an Interior Gateway Protocol, such as OSPF and ISIS, has a
path for. The prefix may be learnt directly through the IGP
redistributed from other protocol(s)
o CE: It is an external router through which an egress PE can
reach a prefix P/m.
o Ingress PE, "iPE": It is a BGP speaker that learns about a
prefix through another IBGP peer and chooses that IBGP peer as
the next-hop for the prefix.
o Path: It is the next-hop in a sequence of unique connected
nodes starting from the current node and ending with the
destination node or network identified by the prefix.
o Recursive path: It is a path consisting only of the IP address
of the next-hop without the outgoing interface. Subsequent
lookups are needed to determine the outgoing interface.
o Non-recursive path: It is a path consisting of the IP address
of the next-hop and one outgoing interface
o Primary path: It is a recursive or non-recursive path that can
be used all the time. A prefix can have more than one primary
path
o Backup path: It is a recursive or non-recursive path that can
be used only after some or all primary paths become unreachable
o Leaf: A leaf is container data structure for a prefix or local
label. Alternatively, it is the data structure that contains
prefix specific information.
o IP leaf: Is the leaf corresponding to an IPv4 or IPv6 prefix
o Label leaf. It is the leaf corresponding to a locally allocated
label such as the VPN label on an egress PE [6].
Bashandy Expires April 21, 2014 [Page 4]
Internet-Draft BGP Prefix Independent Convergence October 2013
o Pathlist: It is an array of paths used by one or more prefix to
forward traffic to destination(s) covered by a IP prefix. Each
path in the pathlist carries its "path-index" that identifies
its position in the array of paths. A pathlist may contain a
mix of primary and backup paths
o OutLabel-Array: Each labeled prefix is associated with an
OutLabel-Array. The OutLabel-Array is a list of one or more
outgoing labels and/or label actions where each label or label
action has 1-to-1 correspondence to a path in the pathlist. The
number of entries in the OutLabel-array is identical to the
number of paths in the pathlist and the ith outlabel entry is
associated with the path whose path-index is "i". Label actions
are: push the label, pop the label, or swap the incoming label
with the outlabel. The prefix may be an IGP or BGP prefix
o Adjacency: It is the layer 2 encapsulation leading to the layer
3 directly connected next-hop
o Dependency: An object X is said to be a dependent or Child of
object Y if Object Y cannot be deleted unless object X is no
longer a dependent/child of object Y
o Route: It is a prefix with one or more paths associated with
it. Hence the minimum set of objects needed to construct a
route is a leaf and a pathlist.
2. Constructing the Shared Hierarchical Forwarding Chain
2.1. Databases
The Forwarding Information Base (FIB) on a router maintains 3 basic
databases
o Pathlist-DB: A pathlist is uniquely identified by the list of
paths. The Pathlist DB contains the set of all shared pathlists
o Leaf-DB: A leaf is uniquely identified by the prefix or the label
o Adjacency-DB: An adjacency is uniquely identified by the outgoing
layer 3 interface and the IP address of the next-hop directly
connected to the layer 3 interface. Adjacency DB contains the
list of all adjacencies
Bashandy Expires April 21, 2014 [Page 5]
Internet-Draft BGP Prefix Independent Convergence October 2013
2.2. Constructing the forwarding chain from a downloaded route
1. A prefix with a list of paths is downloaded to FIB from BGP. For
labeled prefixes, an OutLabel-Array and possibly a local label
(e.g. for a VPN [6] prefix on an egress PE) are also downloaded
2. If the prefix does not exist, construct a new IP leaf from the
downloaded prefix. If a local label is allocated, construct a
label leaf from the local label
3. Construct an OutLabel-Array and attach the Outlabel array to the
IP and label leaf
4. The list of paths attached to the route is looked up in the
pathlist-DB
5. If a pathlist PL is found
a. Retrieve the pathlist
6. Else
a. Construct a new pathlist
b. Insert the new pathlist in the pathlist-DB
c. Resolve the paths of the pathlist as follows
d. Recursive path:
i. Lookup the next-hop in the leaf-DB
ii. If a leaf with at least one reachable path is found, add
the path to the dependency list of the leaf
iii. Otherwise the path remains unresolved and cannot be used
for forwarding
e. Non-recursive path
i. Lookup the next-hop and outgoing interface in the
adjacency-DB
ii. If an adjacency is found, add the path to the dependency
list of adjacency
iii. Otherwise, create a new adjacency and add the path to
its dependency list
7. Attach the leaf(s) as (a) dependent(s) of the pathlist
Bashandy Expires April 21, 2014 [Page 6]
Internet-Draft BGP Prefix Independent Convergence October 2013
As a result of the above steps, a forwarding chain starting with a
leaf and ending with one or more adjacency is constructed. It is
noteworthy to mention that the forwarding chain is constructed
without any operator intervention at all.
2.3. Examples
This section outlines two examples that we will use for illustration
for the rest of the document. The examples use a standard multihomed
VPN [6] prefix in a BGP-free core running LDP. The topology is
depicted in Figure 1.
+-----------------------------------+
| |
| LDP Core |
| |
| ePE2
| |\
| | \
| | \
| | \
iPE | CE.......VRF "Blue"
| | / (VPN-P1)
| | / (VPN-P2)
| | /
| |/
| ePE1
| |
| |
| |
+-----------------------------------+
Figure 1 VPN prefix reachable via multiple PEs
The first example is an illustration of ECMP while the second
example is an illustration of primary-backup paths
2.3.1. Example 1: Forwarding Chain for iBGP ECMP
Consider the case of the ingress PE (iPE) in the multi-homed VPN
prefixes depicted in Figure 1. Suppose the iPE receives route
advertisements for the VPN prefixes VPN-P1 and VPN-P2 from two
egress PEs, ePE1 and ePE2 with next-hop BGP-NH1 and BGP-NH2,
respectively. Assume that ePE1 advertise the VPN labels VPN-L11 and
VPN-L12 while ePE2 advertise the VPN labels VPN-L21 and VPN-L22 for
VPN-P1 and VPN-P2, respectively. Suppose that BGP-NH1 and BGP-NH2
are resolved via the IGP prefixes IGP-P1 and IGP-P2, which also
happen to have 2 ECMP paths with IGP-NH1 and IGP-NH2 reachable via
the interfaces I1 and I2. Suppose that LDP on the downstream LSRs
for IGP-P1 and IGP-P2 are assign the LDP labels LDP-L1 and LDP-L2 to
Bashandy Expires April 21, 2014 [Page 7]
Internet-Draft BGP Prefix Independent Convergence October 2013
the prefixes IGP-P1 and IGP-P2. The forwarding chain on the ingress
PE "iPE" for the VPN prefixes is depicted in Figure 2.
BGP OutLabel Array
+---------+
| VPN-L11 |
+--->+---------+
| | VPN-L21 |
| +---------+ IGP OutLabel Array
| +---------+
| | LDP-L11 |
| +-->+---------+
| | | LDP-L21 |
VPN-P1------+ | +---------+
| |
| |
| IGP-P1-----+
| ^ |
| | |
V | V IGP Pathlist
+--------+ | +-------------+
|BGP-NH1 |---------------+ | IGP-NH1, I1 |------>adj1
BGP +--------+ +-------------+
Pathlist |BGP-NH2 |----+ | IGP-NH2, I2 |------>adj2
+--------+ | +-------------+
^ | ^
| | |
| | |
| IGP-P2----------------+
| |
| |
VPN-P2------+ | +---------+
| | | LDP-L12 |
| +--->+---------+
| | LDP-L22 |
| +---------+
| +---------+ IGP OutLabel Array
| | VPN-L12 |
+--->+---------+
| VPN-L22 |
+---------+
BGP OutLabel Array
Figure 2 Forwarding Chain for VPN Prefixes with iBGP ECMP
The structure depicted in Figure 2 illustrates the two important
properties discussed in this memo: sharing and hierarchy. We can
Bashandy Expires April 21, 2014 [Page 8]
Internet-Draft BGP Prefix Independent Convergence October 2013
see that the both the BGP and IGP pathlists are shared among
multiple BGP and IGP prefixes, respectively. At the same time, the
forwarding chain objects depend on each other in a child-parent
relation instead of being collapsed into a single level.
2.3.2. Example 2: Primary Backup Paths
Consider the egress PE ePE1 in the case of the multi-homed VPN
prefixes in the BGP-free LDP core depicted in Figure 1. Suppose ePE1
determines that the primary path is the external path but the backup
path is the iBGP path to the other PE ePE2 with next-hop BGP-NH2.
ePE2 constructs the forwarding chain depicted in Figure 1. We are
only showing a single VPN prefix for simplicity. But all prefixes
that are multihomed to ePE1 and ePE2 share the BGP pathlist
BGP OutLabel Array
VPL-L11 +---------+
(Label-leaf)---+---->|Unlabeled|
| +---------+
| | VPN-L21 |
| | (swap) |
| +---------+
| ^
| | BGP Pathlist
| | +------------+ Connected route
| | | CE-NH |------>(to the CE)
| | |path-index=0|
| | +------------+
V | | VPN-NH2 |
VPN-P1 ------------------+------>| (backup) |------>IGP Leaf
(IP prefix leaf) |path-index=1| (Towards ePE2)
+-----+------+
Figure 3 VPN Prefix Forwarding Chain with eiBGP paths on egress PE
The example depicted in Figure 3 differs from the example in Figure
2 in two main aspects. First as long as the primary path towards the
CE (external path) is useable, it will be the only path used for
forwarding while the OutLabel-Array contains both the unlabeled
label (primary path) and the VPN label (backup path) advertised by
the backup path ePE2. The second aspect is presence of the label
leaf corresponding to the VPN prefix. This label leaf is used to
match VPN traffic arriving from the core. Note that the label leaf
shares the OutLabel-Array and the pathlist with the IP prefix.
Bashandy Expires April 21, 2014 [Page 9]
Internet-Draft BGP Prefix Independent Convergence October 2013
3. Forwarding Behavior
When a packet arrives, it matches a leaf. A labeled packet matches a
label leaf while an IP packet matches an IP prefix leaf. The
forwarding engines walks the forwarding chain starting from the leaf
until the walk terminates on an adjacency. Thus when a packet
arrives, the chain is walked as follows:
1. Lookup the leaf based on the destination address or the label at
the top of the packet
2. Retrieve the parent pathlist of the leaf
3. Pick the outgoing path from the list of resolved paths in the
pathlist. The method by which the outgoing path is picked is
beyond the scope of this document (i.e. flow-preserving hash
exploiting entropy within the MPLS stack and IP header). Let the
"path-index" of the outgoing path be "i".
4. If the prefix is labeled, use the "path-index" "i" to retrieve
the ith label "Li" stored the ith entry in the OutLabel-Array and
apply the label action of the label on the packet (e.g. for VPN
label on the ingress PE, the label action is "push").
5. Move to the parent of the chosen path "i"
6. If the chosen path "i" is recursive, move to its parent prefix
and go to step 2
7. If the chosen path "i" is non-recursive move to its parent
adjacency
8. Encapsulate the packet in the L2 string specified by the
adjacency and send the packet out.
Let's applying the above forwarding steps to the example described
in Figure 1 Section 2.3.1. Suppose a packet arrives at ingress PE
iPE from an external neighbor. Assume the packet matches the VPN
prefix VPN-P1. While walking the forwarding chain, the forwarding
engine applies hashing algorithm to choose the path and the hashing
at the BGP level yields path 0 while the hashing at the IGP level
yields path 1. In that case, the packet will be sent out of
interface I1 with the label stack "LDP-L12,VPN-L21".
4. Forwarding Chain Adjustment at a Failure
The hierarchical and shared structure of the forwarding chain
explained in Section 2. allows modifying a small number of
forwarding chain objects to re-route traffic to a pre-calculated
equal-cost or backup path without the need to modify the possibly
Bashandy Expires April 21, 2014 [Page 10]
Internet-Draft BGP Prefix Independent Convergence October 2013
very large number of BGP prefixes. In this section, we go over
various core and edge failure scenarios to illustrate how FIB
manager can utilize the forwarding chain structure to achieve prefix
independent convergence.
4.1. BGP-PIC core
This section describes the adjustments to the forwarding chain when
a core link or node fails but the BGP next-hop remains reachable.
There are two case: remote link failure and attached link failure.
Node failures are treated as link failures.
When a remote link or node fails, IGP receives advertisement
indicating a topology change so IGP re-converges to either find a
new next-hop and outgoing interface or remove the path completely
from the IGP prefix used to resolve BGP next-hops. IGP and LDP
download the modified IGP leaves with modified outgoing labels for
labeled core. FIB manager modifies the existing IGP leaf by
executing the steps outlined in Section 2.2.
When a local link fails, FIB manager detects the failure almost
immediately. The FIB manager marks the impacted path(s) as unuseable
so that only useable paths are used to forward packets. Note that in
this particular case there is actually no need even to backwalk to
IGP leaves to adjust the OutLabel-Arrays because FIB can rely on the
path-index stored in the useable paths in the loadinfo to pick the
right label.
It is noteworthy to mention that because FIB manager modifies the
forwarding chain starting from the IGP leaves only, BGP pathlists
and leaves are not modified. Hence traffic restoration occurs within
the time frame of IGP convergence, and, for local link failure,
within the timeframe of local detection. Thus it is possible to
achieve sub-50 msec convergence as described in [8] for local link
failure
Let's apply the procedure to the forwarding chain depicted in Figure
2 Section 2.3.1. Suppose a remote link failure occurs and impacts
the first ECMP IGP path to the remote BGP nhop. Upon IGP
convergence, the IGP pathlist of the BGP nhop is updated to reflect
the new topology (one path instead of two). As soon as the IGP
convergence is effective for the BGP nhop entry, the new forwarding
state is immediately available to all dependent BGP prefixes. The
same behavior would occur if the failure was local such as an
interface going down. As soon as the IGP convergence is complete for
the BGP nhop IGP route, all its BGP depending routes benefit from
the new path. In fact, upon local failure, if LFA protection is
Bashandy Expires April 21, 2014 [Page 11]
Internet-Draft BGP Prefix Independent Convergence October 2013
enabled for the IGP route to the BGP nhop and a backup path was pre-
computed and installed in the pathlist, upon the local interface
failure, the LFA backup path is immediately activated (sub-50msec)
and thus protection benefits all the depending BGP traffic through
the hierarchical forwarding dependency between the routes.
4.2. BGP-PIC edge
This section describes the adjustments to the forwarding chains as a
result of edge node or edge link failure
4.2.1. Adjusting forwarding Chain in egress node failure
When an edge node fails, IGP on neighboring core nodes send route
updates indicating that the edge node is no longer reachable. IGP
running on the iBGP peers instructs FIB to remove the IP and label
leaves corresponding to the failed edge node from FIB. So FIB
manager performs the following steps:
o FIB manager deletes the IGP leaf corresponding to the failed edge
node
o FIB manager backwalks to all dependent BGP pathlists and marks
that path using the deleted IGP leaf as unresolved
o Note that there is no need to modify BGP leaves because each path
in the pathlist carries its path index and hence the correct
outgoing label will be picked. So for example the forwarding
chain depicted in Figure 2, if the 1st path becomes unresolved,
then the forwarding engine will only use the second path path for
forwarding. Yet the pathindex of that single resolved path will
still be 1 and hence the label VPN-L21 or VPN-L22 will be pushed
4.2.2. Adjusting Forwarding Chain on PE-CE link Failure
Suppose the link between an edge router and its external peer fails.
There are two scenarios (1) the edge node attached to the failed
link performs next-hop self and (2) the edge node attached to the
failure advertises the IP address of the failed link as the next-hop
attribute to its iBGP peers.
In the first case, the rest of iBGP peers will remain unaware of the
link failure and will continue to forward traffic to the edge node
until the edge node attached to the failed link withdraws the BGP
prefixes. If the destination prefixes are multi-homed to another
iBGP peer, say ePE2, then FIB manager on the edge router detecting
the link failure performs the following tasks
Bashandy Expires April 21, 2014 [Page 12]
Internet-Draft BGP Prefix Independent Convergence October 2013
o FIB manager backwalks to the BGP pathlists marks the path through
the failed link to the external peer as unresolved
o Hence traffic will be forwarded used the backup path towards ePE2
o For labeled traffic
o The Outlabel-Array attached to the BGP leaves already
contains an entry corresponding to the path towards ePE2.
o The label entry in OutLabel-Arrays corresponding to the
internal path to ePE2 has swap action and the label
advertised by ePE2
o For an arriving label packet (e.g. VPN), the top label is
swapped with the label advertised by ePE2
o For unlabeled traffic, packets are simply redirected towards ePE2
In the second case where the edge router uses the IP address of the
failed link as the BGP next-hop, the edge router will still perform
the previous steps. But, unlike the case of next-hop self, IGP on
failed edge node informs the rest of the iBGP peers that IP address
of the failed link is no longer reachable. Hence the FIB manager on
iBGP peers will delete the IGP leaf corresponding to the IP prefix
of the failed link. The behavior of the iBGP peers will be identical
to the case of edge node failure outlined in Section 4.2.1.
It is noteworthy to mention that because the edge link failure is
local to the edge router, sub-50 msec convergence can be achieved as
described in [8].
Let's try to apply the case of next-hop self to the forwarding chain
depicted in Figure 3. After failure of the link between ePE1 and CE,
the forwarding engine will route traffic arriving from the core
towards VPN-NH2 with path-index=1. A packet arriving from the core
will contain the label VPN-L11 at top. The label VPN-L11 is swaped
with the label VPN-L21 and the packet is forwarded towards ePE2
4.2.3. Loop Avoidance using Special Label (backup/repair label)
The adjustment of the forwarding chain for edge link failure as
specified in Section 4.2.2. can lead to loops in the following
scenarios:
o Unlabeled traffic when the iBGP and eBGP paths are treated as
ECMP
Bashandy Expires April 21, 2014 [Page 13]
Internet-Draft BGP Prefix Independent Convergence October 2013
o Unlabeled traffic if there is an AS-wide single best path such as
the case where the MED or LOCAL_PREF [2] is used to determine the
best path
o Labeled and unlabeled traffic if the edge link failure was due to
an external peer failure and the external peer is common to both
edge nodes. This scenario results in edge link failure on both
iBGP peers and may result in a mutual loop.
This section proposes advertising a special label as a path
attribute to avoid the possibility of looping. When an edge router
has an external path, whether this path is the BGP best path [2] or
not [4][10][9], the edge router associates a non-transitive path
attribute containing a backup/repair label. The semantics of the
backup/repair label is as follows: A packet arriving with the
backup/repair label at the top MUST either be sent outside the AS
dropped. Details for backup/repair label can be found in [TBD]
5. Properties
5.1 Coverage
All the possible failures are covered, whether they impact a local
or remote IGP path or a local or remote BGP nhop as described in
Section 4. This section provides details for each failure and now
the hierarchical and shared FIB structure proposed in this document
allows recovery that does not depend on number of BGP prefixes
5.1.1 A remote failure on the path to a BGP nhop
Upon IGP convergence, the IGP leaf for the BGP nhop is updated upon
IGP convergence and all the BGP depending routes leverage the new
IGP forwarding state immediately.
This BGP resiliency property only depends on IGP convergence and is
independent of the number of BGP prefixes impacted.
5.1.2 A local failure on the path to a BGP nhop
Upon LFA protection, the IGP leaf for the BGP nhop is updated to use
the precomputed LFA backup path and all the BGP depending routes
leverage this LFA protection.
This BGP resiliency property only depends on LFA protection and is
independent of the number of BGP prefixes impacted.
Bashandy Expires April 21, 2014 [Page 14]
Internet-Draft BGP Prefix Independent Convergence October 2013
5.1.3 A remote iBGP nhop fails
Upon IGP convergence, the IGP leaf for the BGP nhop is deleted and
all the depending BGP Path-Lists are updated to either use the
remaining ECMP BGP best-paths or if none remains available to
activate precomputed backups.
This BGP resiliency property only depends on IGP convergence and is
independent of the number of BGP prefixes impacted.
5.1.4 A local eBGP nhop fails
Upon local link failure detection, the adjacency to the BGP nhop is
deleted and all the depending BGP Path-Lists are updated to either
use the remaining ECMP BGP best-paths or if none remains available
to activate precomputed backups.
This BGP resiliency property only depends on local link failure
detection and is independent of the number of BGP prefixes impacted.
5.2 Performance
When the failure is local (a local IGP nhop failure or a local eBGP
nhop failure), a pre-computed and pre-installed backup is activated
by a local-protection mechanism that does not depend on the number
of BGP destinations impacted by the failure. Sub-50msec is thus
possible even if millions of BGP routes are impacted.
When the failure is remote (a remote IGP failure not impacting the
BGP nhop or a remote BGP nhop failure), an alternate path is
activated upon IGP convergence. All the impacted BGP destinations
benefit from a working alternate path as soon as the IGP convergence
occurs for their impacted BGP nhop even if millions of BGP routes
are impacted.
5.2.1 Perspective
The following table puts the BGP PIC benefits in perspective
assuming
o 1M impacted BGP prefixes
o IGP convergence ~ 500 msec
o local protection ~ 50msec
o FIB Update per BGP destination ~ 100usec conservative,
~ 10usec optimistic
Bashandy Expires April 21, 2014 [Page 15]
Internet-Draft BGP Prefix Independent Convergence October 2013
o BGP Convergence per BGP destination ~ 200usec conservative,
~ 100usec optimistic
Without PIC With PIC
Local IGP Failure 10 to 100sec 50msec
Local BGP Failure 100 to 200sec 50msec
Remote IGP Failure 10 to 100sec 500msec
Local BGP Failure 100 to 200sec 500msec
Upon local IGP nhop failure or remote IGP nhop failure, the existing
primary BGP nhop is intact and usable hence the resiliency only
depends on the ability of the FIB mechanism to reflect the new path
to the BGP nhop to the depending BGP destinations. Without BGP PIC,
a conservative back-of-the-enveloppe estimation for this FIB update
is 100usec per BGP destination. An optimistic estimation is 10usec
per entry.
Upon local BGP nhop failure or remote BGP nhop failure, without the
BGP PIC mechanism, a new BGP Best-Path needs to be recomputed and
new updates need to be sent to peers. This depends on BGP processing
time that will be shared between best-path computation, RIB update
and peer update. A conservative back-of-the-envelope estimation for
this is 200usec per BGP destination. An optimistic estimation is
100usec per entry.
5.3 Automated
The BGP PIC solution does not require any operator involvement. The
process is entirely automated as part of the FIB implementation.
The salient points enabling this automation are:
o Extension of the BGP Best Path to compute a backup BGP nhop [11]
o Sharing of BGP Path-list across BGP destinations with same
primary and backup BGP nhop
o Hierarchical indirection and dependency between BGP Path-List and
IGP-Path-List
5.4 Incremental Deployment
Bashandy Expires April 21, 2014 [Page 16]
Internet-Draft BGP Prefix Independent Convergence October 2013
As soon as one router supports BGP PIC solution, it benefits from
all its benefits without any requirement for other routers to
support BGP PIC.
6. Dependency
This section describes the required functionality in the forwarding
and control planes to support BGP-PIC described in this document
6.1 Hierarchical Hardware FIB
BGP PIC requires a hierarchical hardware FIB support: for each BGP
forwarded packet, a BGP leaf is looked up, then a BGP Path-List is
consulted, then an IGP Path-List then an Adjacency.
An alternative method consists in "flattening" the dependencies when
programming the BGP destinations into HW FIB resulting in
potentially eliminating both the BGP Path-List and IGP Path-List
consultation. Such an approach decreases the number of memory
lookup's per forwarding operation at the expense of HW FIB memory
increase (flattening means less sharing hence duplication), loss of
ECMP properties (flattening means less path-list entropy) and loss
of BGP PIC properties.
6.2 Availability of a secondary BGP next-hop
When the primary BGP nhop fails, BGP PIC depends on the availability
of a pre-computed and pre-installed secondary BGP nhop in the BGP
Path-List.
The existence of a secondary next-hop is clear for the following
reason: a service caring for network availability will require two
disjoint network connections hence two BGP nhops.
The BGP distribution of the secondary next-hop is simple thanks to
the following BGP mechanisms: Add-Path [9], BGP Best-External [4],
diverse path [10], and the frequent use in VPN deployments of
different VPN RD's per PE.
6.3 Pre-Computation of a secondary BGP nhop
[11] describes how a secondary BGP nhop can be precomputed on a per
BGP destination basis.
Bashandy Expires April 21, 2014 [Page 17]
Internet-Draft BGP Prefix Independent Convergence October 2013
7. Security Considerations
No additional security risk is introduced by using the mechanisms
proposed in this document
8. IANA Considerations
No requirements for IANA
9. Conclusions
This document proposes a hierarchical and shared forwarding chain
structure that allows achieving prefix independent convergence,
and in the case of locally detected failures, sub-50 msec
convergence. A router can construct the forwarding chains in a
completely transparent manner with zero operator intervention. It
supports incremental deployment.
10. References
10.1. Normative References
[1] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[2] Rekhter, Y., Li, T., and S. Hares, "A Border Gateway Protocol
4 (BGP-4), RFC 4271, January 2006
[3] Bates, T., Chandra, R., Katz, D., and Rekhter Y.,
"Multiprotocol Extensions for BGP", RFC 4760, January 2007
10.2. Informative References
[4] Marques,P., Fernando, R., Chen, E, Mohapatra, P., Gredler, H.,
"Advertisement of the best external route in BGP", draft-ietf-
idr-best-external-04.txt, April 2011.
[5] Wu, J., Cui, Y., Metz, C., and E. Rosen, "Softwire Mesh
Framework", RFC 5565, June 2009.
[6] Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private
Networks (VPNs)", RFC 4364, February 2006.
[7] De Clercq, J. , Ooms, D., Prevost, S., Le Faucheur, F.,
"Connecting IPv6 Islands over IPv4 MPLS Using IPv6 Provider
Edge Routers (6PE)", RFC 4798, February 2007
[8] O. Bonaventure, C. Filsfils, and P. Francois. "Achieving sub-
50 milliseconds recovery upon bgp peering link failures, "
IEEE/ACM Transactions on Networking, 15(5):1123-1135, 2007
Bashandy Expires April 21, 2014 [Page 18]
Internet-Draft BGP Prefix Independent Convergence October 2013
[9] D. Walton, E. Chen, A. Retana, J. Scudder, "Advertisement of
Multiple Paths in BGP", draft-ietf-idr-add-paths-07.txt, June
2012
[10] R. Raszuk, R. Fernando, K. Patel, D. McPherson, K. Kumaki,
"Distribution of diverse BGP paths", draft-ietf-grow-diverse-
bgp-path-dist-08.txt, July 2012
[11] P. Mohapatra, R. Fernando, C. Filsfils, and R. Raszuk, "Fast
Connectivity Restoration Using BGP Add-path", draft-pmohapat-
idr-fast-conn-restore-02, October 2011
11. Acknowledgments
Special thanks to Neeraj Malhotra and Yuri Tsier for the valuable
help
This document was prepared using 2-Word-v2.0.template.dot.
Bashandy Expires April 21, 2014 [Page 19]
Internet-Draft BGP Prefix Independent Convergence October 2013
Appendix A. Modification History
A.1.1. Changes from Version 01
Some editorial corrections
A.1.2. Changes from Version 00
There were few editorial corrections.
Authors' Addresses
Ahmed Bashandy
Cisco Systems
170 West Tasman Dr, San Jose, CA 95134
Email: bashandy@cisco.com
Clarence Filsfils
Cisco Systems
Brussels, Belgium
Email: cfilsfil@cisco.com
Prodosh Mohapatra
Cumulus Networks
Email: pmohapat@cumulusnetworks.com
Bashandy Expires April 21, 2014 [Page 20]
