Internet DRAFT - draft-shore-tls-dnssec-chain-extension
draft-shore-tls-dnssec-chain-extension
TLS M. Shore
Internet-Draft No Mountain Software
Intended status: Standards Track R. Barnes
Expires: April 21, 2016 Mozilla
S. Huque
Verisign Labs
W. Toorop
NLNet Labs
October 19, 2015
A DANE Record and DNSSEC Authentication Chain Extension for TLS
draft-shore-tls-dnssec-chain-extension-02
Abstract
This draft describes a new TLS extension for transport of a DNS
record set serialized with the DNSSEC signatures needed to
authenticate that record set. The intent of this proposal is to
allow TLS clients to perform DANE authentication of a TLS server
certificate without needing to perform additional DNS record lookups.
It will typically not be used for general DNSSEC validation of TLS
endpoint names.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 21, 2016.
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
Shore, et al. Expires April 21, 2016 [Page 1]
Internet-Draft TLS DNSSEC Chain Extension October 2015
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Requirements Notation . . . . . . . . . . . . . . . . . . . . 2
2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
3. DNSSEC Authentication Chain Extension . . . . . . . . . . . . 3
3.1. Protocol . . . . . . . . . . . . . . . . . . . . . . . . 3
3.2. DNSSEC Authentication Chain Data . . . . . . . . . . . . 4
4. Construction of Serialized Authentication Chains . . . . . . 7
5. Caching and Regeneration of the Authentication Chain . . . . 8
6. Verification . . . . . . . . . . . . . . . . . . . . . . . . 8
7. Trust Anchor Maintenance . . . . . . . . . . . . . . . . . . 8
8. Mandating use of this extension . . . . . . . . . . . . . . . 8
9. Security Considerations . . . . . . . . . . . . . . . . . . . 9
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 9
11. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 9
12. References . . . . . . . . . . . . . . . . . . . . . . . . . 9
12.1. Normative References . . . . . . . . . . . . . . . . . . 9
12.2. Informative References . . . . . . . . . . . . . . . . . 10
Appendix A. Pseudocode example . . . . . . . . . . . . . . . . . 11
Appendix B. Test vector . . . . . . . . . . . . . . . . . . . . 11
1. Requirements Notation
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
2. Introduction
This draft describes a new TLS [RFC5246] extension for transport of a
DNS record set serialized with the DNSSEC signatures [RFC4034] needed
to authenticate that record set. The intent of this proposal is to
allow TLS clients to perform DANE authentication [RFC6698] of a TLS
server certificate without performing perform additional DNS record
lookups and incurring the associated latency penalty. It also
provides the ability to avoid potential problems with TLS clients
being unable to look up DANE records because of an interfering or
broken middlebox on the path between the endpoint and a DNS server.
And lastly, it allows a TLS client to validate DANE records itself
without needing access to a validating DNS resolver to which it has a
Shore, et al. Expires April 21, 2016 [Page 2]
Internet-Draft TLS DNSSEC Chain Extension October 2015
secure connection. It will typically not be used for general DNSSEC
validation of endpoint names, but is more appropriate for validation
of DANE TLSA records.
This mechanism is useful for TLS applications that need to address
the problems described above, typically web browsers or VoIP and XMPP
services. It may not be relevant for many other applications. For
example, SMTP MTAs are usually located in data centers, may tolerate
extra DNS lookup latency, are on servers where it is easier to
provision a validating resolver, or are less likely to experience
traffic interference from misconfigured middleboxes. Furthermore,
SMTP MTAs usually employ Opportunistic Security [RFC7435], in which
the presence of the DNS TLSA records is used to determine whether to
enforce an authenticated TLS connection. Hence DANE authentication
of SMTP MTAs [RFC7672] will typically not use this mechanism.
The extension described here allows a TLS client to request in the
client hello message that the DNS authentication chain be returned in
the (extended) server hello message. If the server is configured for
DANE authentication, then it performs the appropriate DNS queries,
builds the authentication chain, and returns it to the client. The
server will usually use a previously cached authentication chain, but
it will need to rebuild it periodically as described in Section 5.
The client then authenticates the chain using a pre-configured trust
anchor.
This specification is based on Adam Langley's original proposal for
serializing DNSSEC authentication chains and delivering them in an
X.509 certificate extension [AGL]. It modifies the approach by using
wire format DNS records in the serialized data (assuming that the
data will be prepared and consumed by a DNS-specific library), and by
using a TLS extension to deliver the data.
3. DNSSEC Authentication Chain Extension
3.1. Protocol
A client MAY include an extension of type "dnssec_chain" in the
(extended) ClientHello. The "extension_data" field of this extension
MUST be empty.
Shore, et al. Expires April 21, 2016 [Page 3]
Internet-Draft TLS DNSSEC Chain Extension October 2015
Servers receiving a "dnssec_chain" extension in the client hello, and
which are capable of being authenticated via DANE, SHOULD return a
serialized authentication chain in the extended ServerHello message,
using the format described below. If a server is unable to return a
authentication chain, or does not wish to return a authentication
chain, it does not include a dnssec_chain extension. As with all TLS
extensions, if the server does not support this extension it will not
return any authentication chain.
3.2. DNSSEC Authentication Chain Data
The "extension_data" field of the "dnssec_chain" extension MUST
contain a DNSSEC Authentication Chain encoded in the following form:
opaque AuthenticationChain<0..2^16-1>;
The AuthenticationChain structure is composed of a sequence of
uncompressed wire format DNS resource record sets (RRset) and
corresponding signatures (RRsig) records. The record sets and
signatures are presented in validation order, starting at the target
DANE record, followed by the DNSKEY and DS record sets for each
intervening DNS zone up to a trust anchor chosen by the server,
typically the DNS root.
This sequence of native DNS wire format records enables easier
generation of the data structure on the server and easier
verification of the data on client by means of existing DNS library
functions. However this document describes the data structure in
sufficient detail that implementers if they desire can write their
own code to do this.
[TODO: mention that to reduce the size of the chain, the server can
deliver exactly one RRsig per RRset, namely the one used to validate
the chain as it is built.]
Each RRset in the chain is composed of a sequence of wire format DNS
resource records. The format of the resource record is described in
RFC 1035 [RFC1035], Section 3.2.1. The resource records SHOULD be
presented in the canonical form and ordering as described in RFC 4034
[RFC4034].
RR(i) = owner | type | class | TTL | RDATA length | RDATA
Shore, et al. Expires April 21, 2016 [Page 4]
Internet-Draft TLS DNSSEC Chain Extension October 2015
RRs within the RRset are ordered canonically, by treating the RDATA
portion of each RR as a left-justified unsigned octet sequence in
which the absence of an octet sorts before a zero octet.
The RRsig record is in DNS wire format as described in RFC 4034
[RFC4034], Section 3.1. The signature portion of the RDATA, as
described in the same section, is the following:
signature = sign(RRSIG_RDATA | RR(1) | RR(2)... )
where, RRSIG_RDATA is the wire format of the RRSIG RDATA fields with
the Signer's Name field in canonical form and the signature field
excluded.
The first RRset in the chain MUST contain the DANE records being
presented. The subsequent RRsets MUST be a sequence of DNSKEY and DS
RRsets, starting with a DNSKEY RRset. Each RRset MUST authenticate
the preceding RRset:
A DNSKEY RRset must include the DNSKEY RR containing the public
key used to verify the previous RRset.
For a DS RRset, the set of key hashes MUST overlap with the
preceding set of DNSKEY records.
In addition, a DNSKEY RRset followed by a DS RRset MUST be self-
signed, in the sense that its RRSIG MUST verify under one of the keys
in the DNSKEY RRSET.
The final DNSKEY RRset in the authentication chain, containing the
trust anchor may be omitted. If omitted, the client MUST verify that
the key tag and owner name in the final RRSIG record correspond to a
trust anchor. There may however be reason to include the trust
anchor RRset and signature if clients are expected to use RFC5011
compliant key rollover functions inband via the chain data. In that
case, they will need to periodically inspect flags (revocation and
secure entry point flags) on the trust anchor DNSKEY RRset.
For example, for an HTTPS server at www.example.com, where there are
zone cuts at "com." and "example.com.", the AuthenticationChain
structure would comprise the following RRsets and signatures (the
data field of the records are omitted here for brevity):
_443._tcp.www.example.com. TLSA
RRSIG(_443._tcp.www.example.com. TLSA)
Shore, et al. Expires April 21, 2016 [Page 5]
Internet-Draft TLS DNSSEC Chain Extension October 2015
example.com. DNSKEY
RRSIG(example.com. DNSKEY)
example.com. DS
RRSIG(example.com. DS)
com. DNSKEY
RRSIG(com. DNSKEY)
com. DS
RRSIG(com. DS)
. DNSKEY
RRSIG(. DNSKEY)
Names that are aliased via CNAME and/or DNAME records may involve
multiple branches of the DNS tree. In this case the authentication
chain structure will be composed of a sequence of these multiple
intersecting branches. DNAME chains should omit unsigned CNAME
records that may have been synthesized in the response from a DNS
resolver. Wildcard DANE records will need to include the wildcard
name as well as a negative proof (i.e. NSEC or NSEC3 records) that no
closer name exists.
A CNAME example:
_443._tcp.www.example.com. IN CNAME ca.example.net.
ca.example.net. IN TLSA 2 0 1 ...
Here the authentication chain structure is composed of two
consecutive chains, one for _443._tcp.www.example.com/CNAME
and one for ca.example.net/TLSA. The second chain can omit
the record sets at the end that overlap with the first.
TLS DNSSEC chain components:
_443._tcp.www.example.com. CNAME
RRSIG(_443._tcp.www.example.com. CNAME)
example.com. DNSKEY
RRSIG(example.com. DNSKEY)
example.com. DS
RRSIG(example.com. DS)
com. DNSKEY
RRSIG(com. DNSKEY)
com. DS
RRSIG(com. DS)
. DNSKEY
RRSIG(. DNSKEY)
ca.example.net. TLSA
Shore, et al. Expires April 21, 2016 [Page 6]
Internet-Draft TLS DNSSEC Chain Extension October 2015
RRSIG(ca.example.net. TLSA)
example.net. DNSKEY
RRSIG(example.net. DNSKEY)
example.net. DS
RRSIG(example.net. DS)
net. DNSKEY
RRSIG(net. DNSKEY)
net. DS
RRSIG(net. DS)
4. Construction of Serialized Authentication Chains
This section describes a possible procedure for the server to use to
build the serialized DNSSEC chain.
When the goal is to perform DANE authentication [RFC6698] of the
server's X.509 certificate, the DNS record set to be serialized is a
TLSA record set corresponding to the server's domain name.
The domain name of the server MUST be that included in the TLS Server
Name Indication extension [RFC6066] when present. If the Server Name
Indication extension is not present, or if the server does not
recognize the provided name and wishes to proceed with the handshake
rather than to abort the connection, the server uses the domain name
associated with the server IP address to which the connection has
been established.
The TLSA record to be queried is constructed by prepending the _port
and _transport labels to the domain name as described in [RFC6698],
where "port" is the port number associated with the TLS server. The
transport is "tcp" for TLS servers, and "udp" for DTLS servers. The
port number label is the left-most label, followed by the transport,
followed by the base domain name.
The components of the authentication chain are built by starting at
the target record set and its corresponding RRSIG. Then traversing
the DNS tree upwards towards the trust anchor zone (normally the DNS
root), for each zone cut, the DNSKEY and DS RRsets and their
signatures are added. If DNS responses messages contain any domain
names utilizing name compression [RFC1035], then they must be
uncompressed.
In the future, proposed DNS protocol enhancements, such as the EDNS
Chain Query extension [CHAINQUERY] may offer easy ways to obtain all
of the chain data in one transaction with an upstream DNSSEC aware
recursive server.
Shore, et al. Expires April 21, 2016 [Page 7]
Internet-Draft TLS DNSSEC Chain Extension October 2015
5. Caching and Regeneration of the Authentication Chain
DNS records have Time To Live (TTL) parameters, and DNSSEC signatures
have validity periods (specifically signature expiration times).
After the TLS server constructs the serialized authentication chain,
it SHOULD cache and reuse it in multiple TLS connection handshakes.
However, it MUST refresh and rebuild the chain as TTLs and signature
validity periods dictate. A server implementation could carefully
track these parameters and requery component records in the chain
correspondingly. Alternatively, it could be configured to rebuild
the entire chain at some predefined periodic interval that does not
exceed the DNS TTLs or signature validity periods of the component
records in the chain.
6. Verification
A TLS client making use of this specification, and which receives a
DNSSEC authentication chain extension from a server, SHOULD use this
information to perform DANE authentication of the server certificate.
In order to do this, it uses the mechanism specified by the DNSSEC
protocol [RFC4035]. This mechanism is sometimes implemented in a
DNSSEC validation engine or library.
If the authentication chain is correctly verified, the client then
performs DANE authentication of the server according to the DANE TLS
protocol [RFC6698], and the additional protocol requirements outlined
in [RFC7671].
7. Trust Anchor Maintenance
The trust anchor may change periodically, e.g. when the operator of
the trust anchor zone performs a DNSSEC key rollover. Managed key
rollovers typically use a process that can be tracked by verifiers
allowing them to automatically update their trust anchors, as
described in [RFC5011]. TLS clients using this specification are
also expected to use such a mechanism to keep their trust anchors
updated. Some operating systems may have a system-wide service to
maintain and keep the root trust anchor up to date. In such cases,
the TLS client application could simply reference that as its trust
anchor, periodically checking whether it has changed.
8. Mandating use of this extension
A TLS server certificate MAY mandate the use of this extension by
means of the X.509 TLS Feature Extension described in [RFC7633].
This X.509 certificate extension, when populated with the
dnssec_chain TLS extension identifier, indicates to the client that
the server must deliver the authentication chain when asked to do so.
Shore, et al. Expires April 21, 2016 [Page 8]
Internet-Draft TLS DNSSEC Chain Extension October 2015
(The X.509 TLS Feature Extension is the same mechanism used to
deliver other mandatory signals, such as OCSP "must staple"
assertions.)
9. Security Considerations
The security considerations of the normatively referenced RFCs (1035,
4034, 4035, 5246, 6066, 6698, 7633, 7671) all pertain to this
extension. Since the server is delivering a chain of DNS records and
signatures to the client, it MUST rebuild the chain in accordance
with TTL and signature expiration of the chain components as
described in Section 5. TLS clients need roughly accurate time in
order to properly authenticate these signatures. This could be
achieved by running a time synchronization protocol like NTP
[RFC5905] or SNTP [RFC4330], which are already widely used today.
TLS clients MUST support a mechanism to track and rollover the trust
anchor key, or be able to avail themselves of a service that does
this, as described in Section 7.
10. IANA Considerations
This extension requires the registration of a new value in the TLS
ExtensionsType registry. The value requested from IANA is 53. If
the draft is adopted by the WG, the authors expect to make an early
allocation request as specified in [RFC7120].
11. Acknowledgments
Many thanks to Adam Langley for laying the groundwork for this
extension. The original idea is his but our acknowledgment in no way
implies his endorsement. This document also benefited from
discussions with and review from the following people: Viktor
Dukhovni, Daniel Kahn Gillmor, Jeff Hodges, Allison Mankin, Patrick
McManus, Gowri Visweswaran, Duane Wessels, Nico Williams, and Paul
Wouters.
12. References
12.1. Normative References
[RFC1035] Mockapetris, P., "Domain names - implementation and
specification", STD 13, RFC 1035, November 1987.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
Shore, et al. Expires April 21, 2016 [Page 9]
Internet-Draft TLS DNSSEC Chain Extension October 2015
[RFC4034] Arends, R., Austein, R., Larson, M., Massey, D., and S.
Rose, "Resource Records for the DNS Security Extensions",
RFC 4034, March 2005.
[RFC4035] Arends, R., Austein, R., Larson, M., Massey, D., and S.
Rose, "Protocol Modifications for the DNS Security
Extensions", RFC 4035, March 2005.
[RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security
(TLS) Protocol Version 1.2", RFC 5246, August 2008.
[RFC6066] Eastlake, D., "Transport Layer Security (TLS) Extensions:
Extension Definitions", RFC 6066, January 2011.
[RFC6698] Hoffman, P. and J. Schlyter, "The DNS-Based Authentication
of Named Entities (DANE) Transport Layer Security (TLS)
Protocol: TLSA", RFC 6698, August 2012.
[RFC7633] Hallam-Baker, P., "X.509v3 Transport Layer Security (TLS)
Feature Extension", RFC 7633, DOI 10.17487/RFC7633,
October 2015, <http://www.rfc-editor.org/info/rfc7633>.
[RFC7671] Dukhovni, V. and W. Hardaker, "The DNS-Based
Authentication of Named Entities (DANE) Protocol: Updates
and Operational Guidance", RFC 7671, DOI 10.17487/RFC7671,
October 2015, <http://www.rfc-editor.org/info/rfc7671>.
12.2. Informative References
[RFC4330] Mills, D., "Simple Network Time Protocol (SNTP) Version 4
for IPv4, IPv6 and OSI", RFC 4330, January 2006.
[RFC5011] StJohns, M., "Automated Updates of DNS Security (DNSSEC)
Trust Anchors", STD 74, RFC 5011, September 2007.
[RFC5905] Mills, D., Martin, J., Burbank, J., and W. Kasch, "Network
Time Protocol Version 4: Protocol and Algorithms
Specification", RFC 5905, June 2010.
[RFC7120] Cotton, M., "Early IANA Allocation of Standards Track Code
Points", BCP 100, RFC 7120, January 2014.
[RFC7435] Dukhovni, V., "Opportunistic Security: Some Protection
Most of the Time", RFC 7435, December 2014.
[RFC7672] Dukhovni, V. and W. Hardaker, "SMTP Security via
Opportunistic DNS-Based Authentication of Named Entities
(DANE) Transport Layer Security (TLS)", RFC 7672, DOI
Shore, et al. Expires April 21, 2016 [Page 10]
Internet-Draft TLS DNSSEC Chain Extension October 2015
10.17487/RFC7672, October 2015,
<http://www.rfc-editor.org/info/rfc7672>.
[AGL] Langley, A., "Serializing DNS Records with DNSSEC
Authentication", , <https://tools.ietf.org/id/draft-agl-
dane-serializechain-01.txt>.
[CHAINQUERY]
Wouters, P., "Chain Query Requests in DNS", , <https://
tools.ietf.org/html/draft-ietf-dnsop-edns-chain-query>.
Appendix A. Pseudocode example
[code goes here]
Appendix B. Test vector
[data go here]
Authors' Addresses
Melinda Shore
No Mountain Software
EMail: melinda.shore@nomountain.net
Richard Barnes
Mozilla
EMail: rlb@ipv.sx
Shumon Huque
Verisign Labs
EMail: shuque@verisign.com
Willem Toorop
NLNet Labs
EMail: willem@nlnetlabs.nl
Shore, et al. Expires April 21, 2016 [Page 11]