Internet DRAFT - draft-tschofenig-smart-object-architecture
draft-tschofenig-smart-object-architecture
Network Working Group H. Tschofenig
Internet-Draft J. Arkko
Intended status: Informational D. Thaler
Expires: July 1, 2013 D. McPherson
December 28, 2012
Architectural Considerations in Smart Object Networking
draft-tschofenig-smart-object-architecture-03.txt
Abstract
Following the theme "Everything that can be connected will be
connected", engineers and researchers designing smart object networks
need to decide how to achieve this in practice. How can different
forms of embedded and constrained devices be interconnected? How can
they employ and interact with the currently deployed Internet? This
memo discusses smart objects and some of the architectural choices
involved in designing smart object networks and protocols that they
use.
The document is being discussed at
https://www.ietf.org/mailman/listinfo/architecture-discuss
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on July 1, 2013.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
Tschofenig, et al. Expires July 1, 2013 [Page 1]
Internet-Draft Smart Object Architectural Considerations December 2012
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Specific and General Purpose Solutions . . . . . . . . . . . . 5
3. Deployment Constraints in the Internet . . . . . . . . . . . . 7
4. The Need for Standards . . . . . . . . . . . . . . . . . . . . 9
4.1. Managing Complexity . . . . . . . . . . . . . . . . . . . 9
4.2. Interoperability Architecture . . . . . . . . . . . . . . 10
4.3. Internet Protocols for Proprietary Protocol
Developments . . . . . . . . . . . . . . . . . . . . . . . 13
4.4. Interoperability . . . . . . . . . . . . . . . . . . . . . 14
4.5. Design for Change . . . . . . . . . . . . . . . . . . . . 16
5. Security Considerations . . . . . . . . . . . . . . . . . . . 17
6. Privacy Considerations . . . . . . . . . . . . . . . . . . . . 18
7. Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 23
9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 24
10. Informative References . . . . . . . . . . . . . . . . . . . . 25
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 27
Tschofenig, et al. Expires July 1, 2013 [Page 2]
Internet-Draft Smart Object Architectural Considerations December 2012
1. Introduction
In RFC 6574 [1], we refer to smart objects as devices with
constraints on energy, bandwidth, memory, size, cost, etc. This is a
fuzzy definition, as there is clearly a continuum in device
capabilities and there is no hard line to draw between devices that
can be classified as smart objects and those that can't.
Following the theme "Everything that can be connected will be
connected", engineers and researchers designing smart object networks
need to address a number of questions. How can different forms of
embedded and constrained devices be interconnected? How can they
employ and interact with the currently deployed Internet?
These questions have been discussed at length. For instance, when
the Internet Architecture Board (IAB) scheduled a workshop on Smart
Objects, the IETF community was asked to develop views on how
Internet protocols can be utilized by smart objects. A report of the
discussions and the position papers received for this workshop have
been published [1].
This memo discusses smart objects and some of the architectural
choices involved in designing smart object networks and protocols
that they use. The main issues that we focus on are interaction with
the Internet, the use of Internet protocols for these applications,
models of interoperability, and approach to standardization. Many of
the issues discussed in this memo are common to any communications
system design or protocol development. However, given the high
interest for smart object networks, their somewhat specific
requirements, and commonly occurring requests for very different
communications tools prompted the IAB to discuss these issues in this
specific context.
In drawing conclusions from the prior IETF work and from the IAB
workshop it is useful to look back at the criteria for success of the
Internet. Various publications provide insight into the history, and
some of it is very much applicable to the discussion on smart
objects. RFC 1958 [2] says:
"The Internet and its architecture have grown in evolutionary
fashion from modest beginnings, rather than from a Grand Plan."
It goes on to add:
"A good analogy for the development of the Internet is that of
constantly renewing the individual streets and buildings of a
city, rather than razing the city and rebuilding it."
Tschofenig, et al. Expires July 1, 2013 [Page 3]
Internet-Draft Smart Object Architectural Considerations December 2012
Internet protocols are immediately relevant for any smart object
development and deployment. However, building very small, often
battery-operated devices is challenging. It is difficult to resist
the temptation to build specific solutions tailored to a particular
application, or to re-design everything from scratch. Yet, due to
network effects, the case for using the Internet Protocol(s) and
other generic technology is compelling.
As technology keeps advancing, the constraints that the technology
places on devices evolve as well. Microelectronics become more
capable as time goes by, sometimes making it even possible for new
devices to be both less expensive and more capable than their
predecessors. This trend can, however, be in some cases offset by
the desire to embed communications technology in even smaller and
cheaper objects. But it is important to design communications
technology not just for today's constraints, but also tomorrow's.
This writeup describes the IAB's view on these issues. The document
is being discussed at
https://www.ietf.org/mailman/listinfo/architecture-discuss.
The rest of the document is organized as follows. Section 2
discusses the problems associated with vertically integrated
industry-specific solutions, and suggests the use of generic
technologies and a more flexible architecture as a way to reduce
these problems. Section 3 discusses the problems associated with
attempting to use options and communication patterns other than those
in current widespread use in the Internet. Often middleboxes and
assumptions built into existing devices makes such usage problematic.
Section 4 discusses different levels of interoperability, and the
different level of effort required to achieve them. Finally,
Section 5 presents some of the relevant security issues, Section 6
discusses privacy, and Section 7 summarizes the recommendations.
Tschofenig, et al. Expires July 1, 2013 [Page 4]
Internet-Draft Smart Object Architectural Considerations December 2012
2. Specific and General Purpose Solutions
The Internet protocols are relevant for any smart object development
and deployment. In the context of one use case of smart objects, the
smart grid and smart meters in particular, RFC 6272 "Internet
Protocols for the Smart Grid" [3] identifies a range of IETF
protocols that can be utilized.
Of course, there are also many protocols that are unlikely to be
needed or even suitable for the smart object environments. For
instance, it would difficult to imagine inter-domain routing being a
necessary feature in these objects; there are other devices in the
network that would normall be responsible for this functionality.
But the wide range of protocols listed in RFC 6272 illustrates the
view of the IAB about how a large fraction of the Internet technology
can be readily used in these new applications. Many commercial
products employ proprietary or industry-specific protocol mechanisms
that do not accommodate direct Internet connectivity. Researchers
have made several attempts to design new types of architectures for
the entire Internet system. But by and large the industry has
understood the value of using Internet communications for various
smart object deployments.
Nevertheless, there are several architectural concerns that deserve
to be highlighted.
Vertically Specified Profiles
The discussions at the IAB workshop (see Section 3.1.2 of [1])
revealed the preference of many participants to develop domain
specific profiles that select a minimum subset of protocols needed
for a specific operating environment. Various standardization
organizations and industry fora are currently engaged in
activities of defining their preferred profile(s). Ultimately,
however, the number of domains where smart objects can be used is
essentially unbounded. There is also an ever-evolving set of
protocols and protocol extensions. Profiles, particularly, full-
stack profiles are common, for instance, in areas where existing
legacy technology is being migrated to IP.
However, merely changing the networking protocol to IP does not
necessarily bring the kinds of benefits that industries are
looking for in their evolving smart object deployments. In
particular, a profile is rigid, and leaves little room for
interoperability among slightly differing, or competing technology
variations. As an example, layer 1 through 7 type profiles do not
account for the possibility that some devices may use other
physical media than others, and that in such situations a simple
Tschofenig, et al. Expires July 1, 2013 [Page 5]
Internet-Draft Smart Object Architectural Considerations December 2012
router could still provide an ability to communicate between the
parties.
Industry-Specific Solutions
The Internet Protocol suite is more extensive than merely the use
of IP. Often significant benefits can be gained from using
additional, widely available, generic technologies such as web
services. Benefits from using these kinds of tools include access
to large available workforce, software, and education already
geared towards employing the technology.
Tight Coupling
Many applications are built around a specific set of servers,
devices, and users. However, often the same data and devices
could be useful for many purposes, some of which may not be easily
identifiable at the time that the devices are deployed.
As a result, the following recommendations can be made. First, while
there are some cases where specific solutions are needed, the
benefits of general-purpose technology are often compelling, be it
about choosing IP over some more specific communication mechanism, a
widely deployed link layer (such as wireless LAN) over a more
specific one, web technology over application specific protocols, and
so on.
However, when employing these technologies it is important to embrace
them in their entirety, allowing for the architectural flexibility
that is built onto them. As an example, it rarely makes sense to
limit communications on-link or to specific media. We should also
design our applications so that the participating devices can easily
interact with multiple other applications.
Tschofenig, et al. Expires July 1, 2013 [Page 6]
Internet-Draft Smart Object Architectural Considerations December 2012
3. Deployment Constraints in the Internet
Despite the applicability of the Internet Protocols for smart
objects, picking the specific protocols for a particular use case can
be tricky. As the Internet has evolved over time, certain protocols
and protocol extensions have become the norm and others have become
difficult to use in all circumstances.
Taking into account these constraints is particularly important for
smart objects, as there is often a desire to employ specific features
to support smart object communication. For instance, from a pure
protocol specifications perspective some transport protocols may be
more desirable than others. These constraints apply both to the use
of existing protocols as well as designing new ones on top of the
Internet Protocol stack.
The following list illustrates a few of those constraints, but every
communication protocol comes with its own challenges.
In 2005, [4] studied the usage of IP options-enabled packets in
the Internet and found that overall, approximately half of
Internet paths drop packets with options, making extensions using
IP options "less ideal" for extending IP.
In 2010, [5] tested 34 different home gateways regarding their
packet dropping policy of UDP, TCP, DCCP, SCTP, ICMP, and various
timeout behavior. For example, more than half of the tested
devices do not conform to the IETF recommended timeouts for UDP,
and for TCP the measured timeouts are highly variable, ranging
from less than 4 minutes to longer than 25 hours. For NAT
traversal of DCCP and SCTP, the situation is poor. None of the
tested devices, for example, allowed establishing a DCCP
connection.
In 2011, [6] tested the behavior of networks with regard to
various TCP extensions: "From our results we conclude the
middleboxes implementing layer 4 functionality are very common --
at least 25% of paths interfered with TCP in some way beyond basic
firewalling."
Extending protocols to fulfill new uses and to add new functionality
may range from very easy to difficult, as [7] investigates in great
detail. A challenge many protocol designers are facing is to ensure
incremental deployability and interoperability with incumbent
elements in a number of areas. In various cases, the effort it takes
to design incrementally deployable protocols has not been taken
seriously enough at the outset. RFC 5218 on "What Makes For a
Successful Protocol?" [8] defines the ultimate goal to develop
Tschofenig, et al. Expires July 1, 2013 [Page 7]
Internet-Draft Smart Object Architectural Considerations December 2012
protocols that are deployed beyond their envisioned use cases.
As these examples illustrate, protocol architects have to take
developments in the greater Internet into account, as not all
features can be expected to be usable in all environments. For
instance, middleboxes [9] complicate the use of extensions in the
basic IP protocols and transport layers.
RFC 1958 [2] considers this aspect and says "... the community
believes that the goal is connectivity, the tool is the Internet
Protocol, and the intelligence is end to end rather than hidden in
the network." This statement is challenged more than ever with the
perceived need to develop clever intermediaries interacting with dumb
end devices but we have to keep in mind what RFC 3724 [10] has to say
about this crucial aspect: "One desirable consequence of the end-to-
end principle is protection of innovation. Requiring modification in
the network in order to deploy new services is still typically more
difficult than modifying end nodes." RFC 4924 [11] adds that a
network that does not filter or transform the data that it carries
may be said to be "transparent" or "oblivious" to the content of
packets. Networks that provide oblivious transport enable the
deployment of new services without requiring changes to the core. It
is this flexibility that is perhaps both the Internet's most
essential characteristic as well as one of the most important
contributors to its success.
Tschofenig, et al. Expires July 1, 2013 [Page 8]
Internet-Draft Smart Object Architectural Considerations December 2012
4. The Need for Standards
New smart object applications are developed every day; in many cases
they are created using standardized Internet technology. Even where
a common underlying technology (such as IP) is used, current smart
object networks often have challenges related to interoperability of
the entire protocol stack, including application behavior. One
symptom of such challenges is that various components cannot easily
be replaced by third party components. It is of strategic importance
to make a conscious decision about the desired level of
interoperability and where the points of interconnection are.
4.1. Managing Complexity
These decisions also relate to the required effort to complete the
application, and overall complexity of the system. A system may
appear complex for variety of reasons. First, there is legitimate
heterogeneity in the used networking technology and applications.
This variation is necessary and useful, as for instance different
applications and environments benefit from varying networking
technology. The range and other characteristics of cellular,
wireless local area networking, and RFID are very different from each
other, for instance. There are literally thousands of different
applications, and it is natural that they have differing requirements
on what parties need to communicate with each other, what kind of
security solutions are appropriate, and other aspects.
The answer to managing complexity in the face of this lies in layers
of communication mechanisms and keeping the layers independent, e.g.,
in the form of the hourglass model. If there is a common waist of
the hourglass, then all applications can work over all physical
networking technology, ensuring widest possible coverage of
networking applications. "Everything over IP and IP over
everything." This model provides some guidance for thinking about
the Internet of Things architecture. First of all, it shows how we
need common internetworking infrastructure (IP) to allow
heterogeneous link media to work seamlessly with each other, and with
the rest of the system. Secondly, there are various transport and
middleware communications mechanisms that will likely become useful
in the different applications. For instance, today embedded web
services (HTTP, COAP, XML, and JSON) appear to be popular, regardless
of what specific link technology they are run over.
But there can also be undesirable complexity and variation. Creation
of alternative standards where one would have sufficed may be
harmful. Creating systems and communications mechanisms with
unnecessary dependencies between different layers and system
components limits our ability to migrate systems to the most economic
Tschofenig, et al. Expires July 1, 2013 [Page 9]
Internet-Draft Smart Object Architectural Considerations December 2012
and efficient platforms, and limits our ability to connect as many
objects as possible.
To summarize, complexity and alternative technologies can be very
useful as a part of architecture, or can be problematic when it
creates unnecessary competition and deployment barriers in the market
place. In an optimal situation, complexity will be addressed by
regular technological evolution in the industry through underlying
layering and modular architecture.
4.2. Interoperability Architecture
It is also valuable to look back at earlier IETF publications, for
example, RFC 1263 [12] considers different protocol design strategies
and makes an interesting observation about the decision to design new
protocols from scratch or to design them in a non-backwards
compatible way based on existing protocols:
"We hope to be able to design and distribute protocols in less
time than it takes a standards committee to agree on an acceptable
meeting time. This is inevitable because the basic problem with
networking is the standardization process. Over the last several
years, there has been a push in the research community for
lightweight protocols, when in fact what is needed are lightweight
standards. Also note that we have not proposed to implement some
entirely new set of 'superior' communications protocols, we have
simply proposed a system for making necessary changes to the
existing protocol suites fast enough to keep up with the
underlying change in the network. In fact, the first standards
organization that realizes that the primary impediment to
standardization is poor logistical support will probably win."
While [12] was written in 1991 when the standardization process in
the Internet community was far more lightweight than today (among
other reasons, because fewer stakeholders were interested in
participating in the standards process) it is remarkable to read
these thoughts since they are even more relevant today. This is
particularly true for the smart object environment.
Regardless of how hard we work on optimizing the standard process,
designing systems in an open and transparent consensus process where
many parties participate takes longer than letting individual
stakeholders develop their own proprietary solutions. Therefore, it
is important to make architectural decisions that keep a good balance
between proprietary developments vs. standardized components.
While RFC 1263 [12] certainly provides good food for thought, it also
gives recommendations that may not always be appropriate for the
Tschofenig, et al. Expires July 1, 2013 [Page 10]
Internet-Draft Smart Object Architectural Considerations December 2012
smart object space, such as the preference for a so-called
evolutionary protocol design where new versions of the protocols are
allowed to be non-backwards compatible and all run independently on
the same device. RFC 1263 adds:
"... the only real disadvantage of protocol evolution is the
amount of memory required to run several versions of the same
protocol. Fortunately, memory is not the scarcest resource in
modern workstations (it may, however, be at a premium in the BSD
kernel and its derivatives). Since old versions may rarely if
ever be executed, the old versions can be swapped out to disk with
little performance loss. Finally, since this cost is explicit,
there is a huge incentive to eliminate old protocol versions from
the network."
Even though it is common practice today to run many different
software applications that have similar functionality (for example,
multiple Instant Messaging clients) in parallel it may indeed not be
the most preferred approach for smart objects, which may have severe
limitations regarding RAM, flash memory, and also power constraints.
To deal with exactly this problem, profiles have been suggested in
many cases. Saying "no" to a new protocol stack that only differs in
minor ways may be appropriate but could be interpreted as blocking
innovation and, as RFC 1263 [12] describes it nicely "In the long
term, we envision protocols being designed on an application by
application basis, without the need for central approval.". "Central
approval" here refers to the approval process that happens in a
respective standards developing organization.
So, how can we embrace rapid innovation with distributed developments
and at the same time accomplish a high level of interoperability?
Clearly, standardization of every domain-specific profile will not be
the solution. Many domain-specific profiles are optimizations that
will be already obsoleted by technological developments (e.g., new
protocol developments), new security threats, new stakeholders
entering the system or changing needs of existing stakeholders, new
business models, changed usage patterns, etc. RFC 1263 [12] states
the problem succinctly: "The most important conclusion of this RFC is
that protocol change happens and is currently happening at a very
respectable clip. We simply propose to explicitly deal with the
changes rather keep trying to hold back the flood."
Even worse, different stakeholders that are part of the Internet
milieu have interests that may be adverse to each other, and these
parties each vie to favor their particular interests. In [13],
Clark, et al. call this process 'the tussle' and ask the important
Tschofenig, et al. Expires July 1, 2013 [Page 11]
Internet-Draft Smart Object Architectural Considerations December 2012
question "How can we, as designers, build systems with desired
characteristics and improve the chances that they come out the way we
want?". In an attempt to answer that question, the authors of [13]
develop a high-level principle, which is not tailored to smart object
designs but to Internet protocol develop in general:
"Design for variation in outcome, so that the outcome can be
different in different places, and the tussle takes place within
the design, not by distorting or violating it. Do not design so
as to dictate the outcome. Rigid designs will be broken; designs
that permit variation will flex under pressure and survive."
In order to accomplish this, Clark, et al. suggest to
1. Break complex systems into modular parts.
2. Design for choice.
These are valid guidelines, and many protocols standardized in the
IETF have taken exactly this approach, namely to identify building
blocks that can be used in a wide variety of deployments. Others
then put the building blocks together in a way that suits their
needs. There are, however, limits to this approach. Certain
building blocks are only useful in a limited set of architectural
variants and producing generic building blocks requires a good
understanding of the different architectural variants and often
limits the ability to optimize. Sometimes the value of an individual
building block is hard for others to understand without providing the
larger context, which requires at least to illustrate one deployment
variant that comes with a specific architectural setup. That said,
it is also critical to consider systemic interdependencies between
the set of elements that constitute a system, lest they impose
constraints that weren't envisioned at the outset.
Since many Internet protocols are used as building blocks by other
organizations or in deployments that may have never been envisioned
by the original designs, one can argue that this approach has been
fairly successful. It may, however, not lead to the level of
interoperability many desire: they want interoperability of the
entire system rather than interoperability at a specific protocol
level. Consequently, an important architectural question arises,
namely "What level of interoperability should Internet protocol
engineers aim for?"
In the diagrams below, we illustrate a few interoperability scenarios
with different interoperability needs. Note that these are highly
simplified versions of what protocol architects are facing, since
there are often more parties involved in a sequence of required
Tschofenig, et al. Expires July 1, 2013 [Page 12]
Internet-Draft Smart Object Architectural Considerations December 2012
protocol exchanges, and the entire protocol stack has to be
considered - not just a single protocol layer. As such, the required
coordination and agreement between the different stakeholders is
likely to be far more challenging than illustrated. We do, however,
believe that these figures illustrate that the desired level of
interoperability needs to be carefully chosen.
4.3. Internet Protocols for Proprietary Protocol Developments
Figure 1 shows a typical deployment of many Internet applications.
Here an application service provider (example.com in our
illustration) wants to make an HTTP-based protocol interface
available to its customers. Example.com allows their customers to
upload sensor measurements using a RESTful HTTP design. Customers
need to write code for their embedded systems to make use of the
HTTP-based protocol interface (and keying material for authentication
and authorization of the uploaded data). These applications work
with the servers operated by Example.com and with nobody else. There
is no interoperability with third parties (at the application layer
at least). For instance, Alice, a customer of Example.com, cannot
use their embedded system which was programmed to use the protocol
interface for Example.com with another service provider without re-
writing at least parts of her embedded software. Nevertheless,
Example.com use standardized protocol components to allow for
communication across the Internet and for speeding-up the process of
software development. This is certainly useful from a time-to-market
and cost efficiency point of view. For example, Example.com could
rely on HTTP, offer JSON to encode sensor data, and use IP to allow
various nodes to communicate with each other.
.................
| Application |
| Service |
| Provider |
| Example.com |
|_______________|
_, .
,' `. Proprietary
_,' `. Protocol offered
,' `._ by Example.com
-' -
,'''''''''''''| ,''''''''| Sensors
| Temperature | | Light | operated by
| Sensor | | Sensor | customers of
|.............' |........' Example.com
Tschofenig, et al. Expires July 1, 2013 [Page 13]
Internet-Draft Smart Object Architectural Considerations December 2012
Figure 1: Proprietary Deployment
Clearly, the above scenario does not provide a lot of
interoperability even though standardized Internet protocols are
used.
Figure 2 shows another scenario. Here Example.com is focused on
storage of sensor data and not on the actually processing it offers
an HTTP-based protocol interface to others to get access to the
uploaded sensor data. In our example, b-example.com and
c-example.com are two of such companies that make use of this
functionality in order to provide data visualization and data mining
computations. Example.com again uses standardized protocols (such as
RESTful HTTP design combined with OAuth) for offering access but
overall the entire protocol stack is not standardized.
.................
| Application |
.| Service |
,-` | Provider |
.` | b-example.com |
,-` |_______________|
.`
................. ,-`
| Application |-` Proprietary
| Service | Protocol
| Provider |
| example.com |-,
|_______________| '.
_, `',
Proprietary ,' '. ...
Protocol _,' `', .................
,' '. | Application |
-' `'| Service |
,''''''''| | Provider |
| Light | | c-example.com |
| Sensor | |_______________|
|........'
Figure 2: Backend Interworking
4.4. Interoperability
In contrast to the scenario described in Section 4.3, Figure 3
illustrates a sensor where two devices developed by independent
manufacturers are desired to interwork. This is shown in Figure 3.
Tschofenig, et al. Expires July 1, 2013 [Page 14]
Internet-Draft Smart Object Architectural Considerations December 2012
To pick an example from [1], consider a light bulb that talks to a
light switch with the requirement that each may be manufactured by a
different company, represented as company A and B.
_,,,, ,,,,
/ -'`` \
| |
\ |
/ \
,''''''''| / Standardized . ,''''''''|
| Light | ------|---Protocol-------\------| Light |
| Bulb | . | | Switch |
|........' `'- / |........'
\ _-...-`
Manufacturer `. ,.' Manufacturer
A ` B
Figure 3: Interoperability between two independent devices
In order for this scenario to work manufacturer A, B, and probably
many other manufacturers f lightbulbs and light switches need to get
together and agree on the protocol stack they would like to use. Let
us assume that they do not want any manual configuration by the user
to happen and that these devices should work in a typical home
network this consortium needs to make a decision about the following
protocol design aspects:
o Which physical layer should be supported?
o Which IP version should be used?
o Which IP address configuration mechanism(s) are integrated into
the device?
o Which communication architecture shall be supported? (see [14];
Arkko, et al. explain how the complexity of an application heavily
depends on the chosen communication architecture and discusses an
application with limited communication capabilities, which also
translates into low energy consumption. )
o Whether there is a need for a service discovery mechanism to allow
users to discover light bulbs they have in their home or office.
o Which transport layer protocol is used for conveying the sensor
readings/sensor commands? (e.g., UDP)
Tschofenig, et al. Expires July 1, 2013 [Page 15]
Internet-Draft Smart Object Architectural Considerations December 2012
o Which application layer protocol is used? (for example, CoAP)
o How are requests encoded? (e.g., as URIs) How is the return data
encoded? (e.g., JSON)
o What data model is used for expressing the different light levels?
(e.g., [15])
o Finally, some thoughts will have to be spent about the security
architecture. This includes questions like: what are the
ssecurity threats? What security services need to be provided to
deal with the identified threats? Where do the security
credentials come from? At what layer(s) in the protocol stack
should the security mechanism reside?
This list is not meant to be exhaustive but aims to illustrate that
for every usage scenario many design decisions will have to be made
in order to accommodate the constrained nature of a specific device
in a certain usage scenario. Standardizing such a complete solution
to accomplish a full level of interoperability between two devices
manufactured by different vendors will take time.
4.5. Design for Change
With the description in Section 4.3 and in Section 4.4 we present two
extreme cases of interoperability. To "design for varation in
outcome", as postulated by [13], the design of the system does not
need to be cast in stone during the standardization process but may
be changed during run-time using software updates.
For many reasons, not only for adding new functionality, it can be
said that many smart objects will need a solid software update
mechanism. Note that adding new functionality to smart objects may
not be possible for certain classes of constrained devices, namely
those with severe memory limitations. As such, a certain level of
sophistication from the embedded device is assumed in this section.
Software updates are common in operating systems and application
programs today. Arguably, the Web today employs a very successful
software update mechanism with code being provided by many different
parties (i.e., by websites loaded into the browser or by the Web
application). While JavaScript (or the proposed successor, Dart) may
not be the right choice of software distribution for smart objects,
and other languages such as embedded eLua [16] may be more
appropriate, the basic idea of offering software distribution
mechanisms may present a middleground between the two extreme
interoperability scenario presented in this section.
Tschofenig, et al. Expires July 1, 2013 [Page 16]
Internet-Draft Smart Object Architectural Considerations December 2012
5. Security Considerations
Section 3.3 of [1] reminds us about the IETF workstyle regarding
security:
In the development of smart object applications, as with any other
protocol application solution, security must be considered early
in the design process. As such, the recommendations currently
provided to IETF protocol architects, such as RFC 3552 [17], and
RFC 4101 [18], apply also to the smart object space.
In the IETF, security functionality is incorporated into each
protocol as appropriate, to deal with threats that are specific to
them. It is extremely unlikely that there is a one-size-fits-all
security solution given the large number of choices for the 'right'
protocol architecture (particularly at the application layer). For
this purpose, [3] offers a survey of IETF security mechanisms instead
of suggesting a preferred one.
A more detailed security discussion can be found in the report from
the 'Smart Object Security' workshop. that was held prior to the IETF
meeting in Paris, March 2012. [[Comment.1: The workshop report has
not been published yet. It will happen soon.]]
Tschofenig, et al. Expires July 1, 2013 [Page 17]
Internet-Draft Smart Object Architectural Considerations December 2012
6. Privacy Considerations
In 1980, the Organization for Economic Co-operation and Development
(OECD) published eight Guidelines on the Protection of Privacy and
Trans-Border Flows of Personal Data [19], which are often referred to
as Fair Information Practices (FIPs). The FIPs, like other privacy
principles, are abstract in their nature and have to be applied to a
specific context.
From a technical point of view, many smart object designs are not
radically different from other application design. Often, however,
the lack of a classical user interface, such as is used on a PC or a
phone, that allows users to interact with the devices in a convenient
and familiar way creates problems to provide users with information
about the data collection, and to offer them the ability to express
consent. Furthermore, in some verticals (e.g., smart meter
deployments) users are not presented with the choice of voluntarily
signing up for the service but deployments are instead mandated
through regulation. Therefore, these users have no right to consent;
a right that is core to many privacy principles including the FIPs.
In other cases, the design is more focused on dealing with privacy at
the level of a privacy notice rather than by building privacy into
the design of the system, which [20] asks engineers to do.
Similarly, in many applications smart objects technology is deployed
by someone other than the potentially impacted parties. For
instance, manufacturers and shops deploy RFID tags in products or
governments deploy roadside sensors. In these applications the
impacted parties, such as a shopper or car-owner may not even be
aware that such technology is used, and information about about the
impacted party may be collected.
The interoperability models described in this document highlight that
standardized interfaces are not needed in all cases, nor that this is
even desirable. Depending on the choice of certain underlying
technologies, various privacy problems may be inherited by the upper-
layer protocols and therefore difficult to resolve as an
afterthought. Many smart objects leave users little ability for
enabling privacy-improving configuration changes. Technologies exist
that can be applied also to smart objects to involve users in
authorization decisions before data sharing takes place.
As a summary, for an Internet protocol architect, the guidelines
described in [20] are applicable. For those looking at privacy from
a deployment point of view, the following additional guidelines are
suggested:
Tschofenig, et al. Expires July 1, 2013 [Page 18]
Internet-Draft Smart Object Architectural Considerations December 2012
Transparency: The data processing should be completely transparent
to the smart object owner, users, and possibly impacted parties.
Users and impacted parties must, except in rare exceptional cases,
be put in a position to easily understand what items of personal
information concerning them are collected and stored, as well for
what purposes they are sought.
Data Quality: Smart objects should only store personal data which
are adequate, relevant and not excessive in relation to the
purpose(s) for which they are processed. The use of anonymised
data should be preferred wherever possible.
Data Access: Before deployment starts, it is necessary to consider
who can access the personal data recorded in smart objects and
under which conditions, particularly with regard to data subjects,
to whom (in principle) full and free access to his/her own data
should be recognised. Appropriate and clear procedures should be
established in order to allow data subjects to properly exercise
their rights. A privacy and data protection impact assessment is
considered a useful tool for this analysis.
Data Security: Standardized data security measures to prevent
unlawful access, alteration or loss of smart object data need to
be defined and universally adopted. Robust cryptographic
techniques and proper authentication frameworks should be used to
limit the risk of unintended data transfers or harmful attacks.
The end-user and impacted parties should be able to verify, in a
straight-forward manner, that smart objects are in full compliance
with these standards.
Tschofenig, et al. Expires July 1, 2013 [Page 19]
Internet-Draft Smart Object Architectural Considerations December 2012
7. Summary
Interconnecting smart objects with the Internet creates exciting new
use cases and engineers are eager to play with small and constrained
devices. With various standardization efforts ongoing and the
impression that smart objects require a new Internet Protocol and
many new extensions, we would like to provide a cautious warning. We
believe that protocol architects are best served by the following
high level guidance:
Use Internet protocols
Most, if not all, smart object deployments should employ the
Internet protocol suite. The Internet protocols can be applied to
almost any environment, and the rest of the suite can be tailored
for the specific needs.
The deployed Internet matters
When connecting smart objects to the Internet, take existing
deployment into consideration to avoid unpleasant surprises.
Assuming an ideal, clean-slate deployments is, in many cases, far
too opimistic since already available deployed infrastructure is
sticky.
Decide about the level of interoperability
Offering interoperability between every entity in an architecture
may be an ideal situation for a standards person but comes with a
certain cost. As such, starting with a less ambigious
standardization goal may be appropriate, particularly for early
deployments.
Don't optimize too early
The constrained nature of smart objects invites engineers to
invent each and every technique to optimize protocols for special
use cases. While some of these optimizations may be necessary,
many of them make the overal design complex and the outcome less
usable for the generic use case.
This memo provides also some additional, more detailed suggestions
for different audiences. The following recommendations are for the
designers of smart object systems:
o Even in the smart object space, try to aim for a generic design
instead of optimizing too early. Note that some optimizations
will only be possible in an architectural context, rather than at
Tschofenig, et al. Expires July 1, 2013 [Page 20]
Internet-Draft Smart Object Architectural Considerations December 2012
the level of an individual protocol.
o We encourage engineers to take existing deployment constraints
into consideration to allow for a smooth transition path. This
requires a clear understanding of the deployment status and also
an analysis of the incentives of the different stakeholders.
Over time, a wide range of middleboxes have been introduced to
the Internet protocol suite. Introducing middleboxes in smart
object deployments has been proposed many times but their usage
may turn out to be dangerous. We recommend carefully
investigaing whether new features introduced can be supported
without any change to middleboxes. This investigation will
likely have to go beyond pure specification work, and may
require extensive interoperability testing and a clearly
articulated extensiblity story. The guidance in [7] is
relevant to this discussion. The added architectural
complexity, including security and privacy challenges, has to
be a subject of design considerations. Middleboxes are often
operated by parties other than the communication endpoints. As
such, they introduce additional stakeholders into the
architecture that often want to be involved when new features
are introduced and as such may slow down the ability to
innovate at a high speed.
o The application space has historically seen faster innovation
cycles, and separating network-layer from application-layer
functionality is therefore recommended. In general, we suggest
avoiding standardizing complete protocol stacks. The likelihood
that those will be outdated by the time standardization is
finished is far too high, particularly with application-layer
standards.
o Consider what type of interoperability model is appropriate for
the task at hand. An architecture that requires fewer
interoperability components often has a faster time to market.
Selecting what interfaces are open for interworking between
components from different operators and vendors is very important.
These recommendations are for the designers of new protocols or
protocol extensions in IETF or elsewhere:
o The Internet Protocol stack has a number of building blocks that
have proven useful for many applications. We encourage continuing
the development of building blocks that are usable in a number of
deployment scenarios.
For the development of new components, the recommendations in [1]
Tschofenig, et al. Expires July 1, 2013 [Page 21]
Internet-Draft Smart Object Architectural Considerations December 2012
provide a good starting point. We do, however, encourage protocol
engineers to document the interworking of various protocols in at
least one architectural variant to ensure that the individual
parts indeed fit together without creating gaps or conflicts.
For researchers we offer the following suggestions:
o We believe that the area of mobile code distribution provides a
promising way to solve a range of security problems and the
ability to deliver new functionality. The rich experience from
the Web environment can be taken into consideration as a starting
point.
o We encourage funding of software projects that produce libraries
and open source code for operating systems, basic IP protocol
stacks, and web tools suitable for small, autonomously operating
devices. The success of many IETF protocols can be attributed to
the availability of running code.
o We also propose to conduct ongoing research of the deployment
status of various Internet protocols. These investigations
provide a snapshot for further interactions with the operator
community to ensure that IETF protocols can indeed be deployed in
today's Internet and may stimulate discussions on how to deal with
unpleasant deployment artifacts.
Tschofenig, et al. Expires July 1, 2013 [Page 22]
Internet-Draft Smart Object Architectural Considerations December 2012
8. IANA Considerations
This document does not require actions by IANA.
Tschofenig, et al. Expires July 1, 2013 [Page 23]
Internet-Draft Smart Object Architectural Considerations December 2012
9. Acknowledgements
We would like to thank the participants of the IAB Smart Object
workshop for their input to the overall discussion about smart
objects.
Furthermore, we would like to thank Jan Holler, Patrick Wetterwald,
Atte Lansisalmi, Hannu Flinck, Joel Halpern, Markku Tuohino, and the
IAB for their review comments.
Tschofenig, et al. Expires July 1, 2013 [Page 24]
Internet-Draft Smart Object Architectural Considerations December 2012
10. Informative References
[1] Tschofenig, H. and J. Arkko, "Report from the Smart Object
Workshop", RFC 6574, April 2012.
[2] Carpenter, B., "Architectural Principles of the Internet",
RFC 1958, June 1996.
[3] Baker, F. and D. Meyer, "Internet Protocols for the Smart
Grid", RFC 6272, June 2011.
[4] Fonseca, R., Porter, G., Katz, R., Shenker, S., and I. Stoica,
"IP options are not an option, Technical Report UCB/EECS",
2005.
[5] Eggert, L., "An experimental study of home gateway
characteristics, In Proceedings of the '10th annual conference
on Internet measurement'", 2010.
[6] Honda, M., Nishida, Y., Greenhalgh, A., Handley, M., and H.
Tokuda, "Is it Still Possible to Extend TCP? In Proc. ACM
Internet Measurement Conference (IMC), Berlin, Germany",
Nov 2011.
[7] Carpenter, B., Aboba, B., and S. Cheshire, "Design
Considerations for Protocol Extensions",
draft-iab-extension-recs-13 (work in progress), June 2012.
[8] Thaler, D. and B. Aboba, "What Makes For a Successful
Protocol?", RFC 5218, July 2008.
[9] Carpenter, B. and S. Brim, "Middleboxes: Taxonomy and Issues",
RFC 3234, February 2002.
[10] Kempf, J., Austein, R., and IAB, "The Rise of the Middle and
the Future of End-to-End: Reflections on the Evolution of the
Internet Architecture", RFC 3724, March 2004.
[11] Aboba, B. and E. Davies, "Reflections on Internet
Transparency", RFC 4924, July 2007.
[12] O'Malley, S. and L. Peterson, "TCP Extensions Considered
Harmful", RFC 1263, October 1991.
[13] Clark, D., Wroslawski, J., Sollins, K., and R. Braden, "Tussle
in Cyberspace: Defining Tomorrow's Internet, In Proc. ACM
SIGCOMM", 2002.
Tschofenig, et al. Expires July 1, 2013 [Page 25]
Internet-Draft Smart Object Architectural Considerations December 2012
[14] Arkko, J., Rissanen, H., Loreto, S., Turanyi, Z., and O. Novo,
"Implementing Tiny COAP Sensors",
draft-arkko-core-sleepy-sensors-01 (work in progress),
July 2011.
[15] Jennings, C., "Media Type for Sensor Markup Language (SENML)",
draft-jennings-senml-05 (work in progress), March 2011.
[16] "Embedded Lua Project", 2012.
[17] Rescorla, E. and B. Korver, "Guidelines for Writing RFC Text on
Security Considerations", BCP 72, RFC 3552, July 2003.
[18] Rescorla, E. and IAB, "Writing Protocol Models", RFC 4101,
June 2005.
[19] Organization for Economic Co-operation and Development, "OECD
Guidelines on the Protection of Privacy and Transborder Flows
of Personal Data", available at (September 2010) , http://
www.oecd.org/EN/document/
0,,EN-document-0-nodirectorate-no-24-10255-0,00.html, 1980.
[20] Cooper, A., Tschofenig, H., Aboba, B., Peterson, J., and J.
Morris, "Privacy Considerations for Internet Protocols",
draft-iab-privacy-considerations-02 (work in progress),
March 2012.
[21] Tschofenig, H., Aboba, B., Peterson, J., and D. McPherson,
"Trends in Web Applications and the Implications on
Standardization", draft-tschofenig-post-standardization-02
(work in progress), May 2012.
[22] Shelby, Z., Hartke, K., Bormann, C., and B. Frank, "Constrained
Application Protocol (CoAP)", draft-ietf-core-coap-09 (work in
progress), March 2012.
[23] Bormann, C., "Guidance for Light-Weight Implementations of the
Internet Protocol Suite", draft-bormann-lwig-guidance-01 (work
in progress), January 2012.
[24] Rosenberg, J., "UDP and TCP as the New Waist of the Internet
Hourglass", draft-rosenberg-internet-waist-hourglass-00 (work
in progress), February 2008.
Tschofenig, et al. Expires July 1, 2013 [Page 26]
Internet-Draft Smart Object Architectural Considerations December 2012
Authors' Addresses
Hannes Tschofenig
Linnoitustie 6
Espoo 02600
Finland
Phone: +358 (50) 4871445
Email: Hannes.Tschofenig@gmx.net
URI: http://www.tschofenig.priv.at
Jari Arkko
Jorvas 02420
Finland
Email: jari.arkko@piuha.net
Dave Thaler
US
Email: dthaler@microsoft.com
Danny McPherson
US
Email: danny@tcb.net
Tschofenig, et al. Expires July 1, 2013 [Page 27]