rfc2707
Network Working Group R. Bergman
Request for Comments: 2707 Dataproducts Corp.
Category: Informational T. Hastings, Ed.
Xerox Corporation
S. Isaacson
Novell, Inc.
H. Lewis
IBM Corp.
November 1999
Job Monitoring MIB - V1.0
Status of this Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (1999). All Rights Reserved.
IESG Note
This MIB module uses an unconventional scheme for modeling management
information (on top of the SNMP model) which is unique to this MIB.
The IESG recommends against using this document as an example for the
design of future MIBs.
The "Printer Working Group" industry consortium is not an IETF
working group, and the IETF does not recognize the Printer Working
Group as a standards-setting body. This document is being published
solely to provide information to the Internet community regarding a
MIB that might be deployed in the marketplace. Publication of this
document as an RFC is not an endorsement of this MIB.
Abstract
This document provides a printer industry standard SNMP MIB for (1)
monitoring the status and progress of print jobs (2) obtaining
resource requirements before a job is processed, (3) monitoring
resource consumption while a job is being processed and (4)
collecting resource accounting data after the completion of a job.
This MIB is intended to be implemented (1) in a printer or (2) in a
server that supports one or more printers. Use of the object set is
not limited to printing. However, support for services other than
printing is outside the scope of this Job Monitoring MIB. Future
Bergman, et al. Informational [Page 1]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
extensions to this MIB may include, but are not limited to, fax
machines and scanners.
Table of Contents
1 INTRODUCTION 4
1.1 Types of Information in the MIB 5
1.2 Types of Job Monitoring Applications 6
2 TERMINOLOGY AND JOB MODEL 7
2.1 System Configurations for the Job Monitoring MIB 11
2.1.1 Configuration 1 - client-printer 11
2.1.2 Configuration 2 - client-server-printer - agent in the
server 12
2.1.3 Configuration 3 - client-server-printer - client
monitors printer agent and server 14
3 MANAGED OBJECT USAGE 15
3.1 Conformance Considerations 15
3.1.1 Conformance Terminology 16
3.1.2 Agent Conformance Requirements 16
3.1.2.1 MIB II System Group objects 17
3.1.2.2 MIB II Interface Group objects 17
3.1.2.3 Printer MIB objects 17
3.1.3 Job Monitoring Application Conformance Requirements 17
3.2 The Job Tables and the Oldest Active and Newest Active
Indexes 18
3.3 The Attribute Mechanism and the Attribute Table(s) 20
3.3.1 Conformance of Attribute Implementation 21
3.3.2 Useful, 'Unknown', and 'Other' Values for Objects and
Attributes 21
3.3.3 Index Value Attributes 22
3.3.4 Data Sub-types and Attribute Naming Conventions 22
3.3.5 Single-Value (Row) Versus Multi-Value (MULTI-ROW)
Attributes 23
3.3.6 Requested Objects and Attributes 23
3.3.7 Consumption Attributes 24
3.3.8 Attribute Specifications 24
3.3.9 Job State Reason bit definitions 43
3.3.9.1 JmJobStateReasons1TC specification 44
3.3.9.2 JmJobStateReasons2TC specification 47
3.3.9.3 JmJobStateReasons3TC specification 51
3.3.9.4 JmJobStateReasons4TC specification 51
3.4 Monitoring Job Progress 51
3.5 Job Identification 55
3.5.1 The Job Submission ID specifications 56
3.6 Internationalization Considerations 60
3.6.1 Text generated by the server or device 61
3.6.2 Text supplied by the job submitter 61
3.6.3 'DateAndTime' for representing the date and time 63
Bergman, et al. Informational [Page 2]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
3.7 IANA and PWG Registration Considerations 63
3.7.1 PWG Registration of enums 63
3.7.1.1 Type 1 enumerations 64
3.7.1.2 Type 2 enumerations 64
3.7.1.3 Type 3 enumeration 64
3.7.2 PWG Registration of type 2 bit values 65
3.7.3 PWG Registration of Job Submission Id Formats 65
3.7.4 PWG Registration of MIME types/sub-types for document-
formats 65
3.8 Security Considerations 65
3.8.1 Read-Write objects 65
3.8.2 Read-Only Objects In Other User's Jobs 66
3.9 Notifications 66
4 MIB SPECIFICATION 67
Textual conventions for this MIB module 68
JmUTF8StringTC 68
JmJobStringTC 68
JmNaturalLanguageTagTC 68
JmTimeStampTC 69
JmJobSourcePlatformTypeTC 69
JmFinishingTC 70
JmPrintQualityTC 71
JmPrinterResolutionTC 71
JmTonerEconomyTC 72
JmBooleanTC 72
JmMediumTypeTC 72
JmJobCollationTypeTC 74
JmJobSubmissionIDTypeTC 74
JmJobStateTC 75
JmAttributeTypeTC 78
JmJobServiceTypesTC 81
JmJobStateReasons1TC 83
JmJobStateReasons2TC 83
JmJobStateReasons3TC 83
JmJobStateReasons4TC 84
The General Group (MANDATORY) 84
jmGeneralJobSetIndex (Int32(1..32767)) 85
jmGeneralNumberOfActiveJobs (Int32(0..)) 86
jmGeneralOldestActiveJobIndex (Int32(0..)) 86
jmGeneralNewestActiveJobIndex (Int32(0..)) 86
jmGeneralJobPersistence (Int32(15..)) 87
jmGeneralAttributePersistence (Int32(15..)) 87
jmGeneralJobSetName (UTF8String63) 88
The Job ID Group (MANDATORY) 88
jmJobSubmissionID (OCTET STRING(SIZE(48))) 89
jmJobIDJobSetIndex (Int32(0..32767)) 90
jmJobIDJobIndex (Int32(0..)) 91
The Job Group (MANDATORY) 91
Bergman, et al. Informational [Page 3]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
jmJobIndex (Int32(1..)) 92
jmJobState (JmJobStateTC) 92
jmJobStateReasons1 (JmJobStateReasons1TC) 93
jmNumberOfInterveningJobs (Int32(-2..)) 93
jmJobKOctetsPerCopyRequested (Int32(-2..)) 94
jmJobKOctetsProcessed (Int32(-2..)) 94
jmJobImpressionsPerCopyRequested (Int32(-2..)) 95
jmJobImpressionsCompleted (Int32(-2..)) 96
jmJobOwner (JobString63) 96
The Attribute Group (MANDATORY) 97
jmAttributeTypeIndex (JmAttributeTypeTC) 98
jmAttributeInstanceIndex (Int32(1..32767)) 99
jmAttributeValueAsInteger (Int32(-2..)) 99
jmAttributeValueAsOctets (Octets63) 100
5 APPENDIX A - IMPLEMENTING THE JOB LIFE CYCLE 104
6 APPENDIX B - SUPPORT OF JOB SUBMISSION PROTOCOLS 105
7 REFERENCES 105
8 NOTICES 108
9 AUTHORS' ADDRESSES 109
10 INDEX 111
11 Full Copyright Statement 114
1 Introduction
This specification defines an official Printer Working Group (PWG)
[PWG] standard SNMP MIB for the monitoring of jobs on network
printers. This specification is being published as an IETF
Information Document for the convenience of the Internet community.
In consultation with the IETF Application Area Directors, it was
concluded that this MIB specification properly belongs as an
Information document, because this MIB monitors a service node on the
network, rather than a network node proper.
The Job Monitoring MIB is intended to be implemented by an agent
within a printer or the first server closest to the printer, where
the printer is either directly connected to the server only or the
printer does not contain the job monitoring MIB agent. It is
recommended that implementations place the SNMP agent as close as
possible to the processing of the print job. This MIB applies to
printers with and without spooling capabilities. This MIB is
designed to be compatible with most current commonly-used job
submission protocols. In most environments that support high
function job submission/job control protocols, like ISO DPA [iso-
dpa], those protocols would be used to monitor and manage print jobs
rather than using the Job Monitoring MIB.
Bergman, et al. Informational [Page 4]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
The Job Monitoring MIB consists of a General Group, a Job Submission
ID Group, a Job Group, and an Attribute Group. Each group is a
table. All accessible objects are read-only. The General Group
contains general information that applies to all jobs in a job set.
The Job Submission ID table maps the job submission ID that the
client uses to identify a job to the jmJobIndex that the Job
Monitoring Agent uses to identify jobs in the Job and Attribute
tables. The Job table contains the MANDATORY integer job state and
status objects. The Attribute table consists of multiple entries per
job that specify (1) job and document identification and parameters,
(2) requested resources, and (3) consumed resources during and after
job processing/printing. A larger number of job attributes are
defined as textual conventions that an agent SHALL return if the
server or device implements the functionality so represented and the
agent has access to the information.
1.1 Types of Information in the MIB
The job MIB is intended to provide the following information for the
indicated Role Models in the Printer MIB [print-mib] (Appendix D -
Roles of Users).
User:
Provide the ability to identify the least busy printer. The
user will be able to determine the number and size of jobs
waiting for each printer. No attempt is made to actually
predict the length of time that jobs will take.
Provide the ability to identify the current status of the
user's job (user queries).
Provide a timely indication that the job has completed and
where it can be found.
Provide error and diagnostic information for jobs that did not
successfully complete.
Operator:
Provide a presentation of the state of all the jobs in the
print system.
Provide the ability to identify the user that submitted the
print job.
Provide the ability to identify the resources required by each
job.
Bergman, et al. Informational [Page 5]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
Provide the ability to define which physical printers are
candidates for the print job.
Provide some idea of how long each job will take. However,
exact estimates of time to process a job is not being
attempted. Instead, objects are included that allow the
operator to be able to make gross estimates.
Capacity Planner:
Provide the ability to determine printer utilization as a
function of time.
Provide the ability to determine how long jobs wait before
starting to print.
Accountant:
Provide information to allow the creation of a record of
resources consumed and printer usage data for charging users or
groups for resources consumed.
Provide information to allow the prediction of consumable usage
and resource need.
The MIB supports printers that can contain more than one job at a
time, but still be usable for low end printers that only contain a
single job at a time. In particular, the MIB supports the needs of
Windows and other PC environments for managing low-end direct-connect
(serial or parallel) and networked devices without unnecessary
overhead or complexity, while also providing for higher end systems
and devices.
1.2 Types of Job Monitoring Applications
The Job Monitoring MIB is designed for the following types of
monitoring applications:
1. Monitor a single job starting when the job is submitted and
ending a defined period after the job completes. The Job
Submission ID table provides the map to find the specific job
to be monitored.
2. Monitor all 'active' jobs in a queue, which this
specification generalizes to a "job set". End users may use
such a program when selecting a least busy printer, so the
MIB is designed for such a program to start up quickly and
find the information needed quickly without having to read
Bergman, et al. Informational [Page 6]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
all (completed) jobs in order to find the active jobs.
System operators may also use such a program, in which case
it would be running for a long period of time and may also be
interested in the jobs that have completed. Finally such a
program may be used to provide an enhanced console and
logging capability.
3. Collect resource usage for accounting or system utilization
purposes that copy the completed job statistics to an
accounting system. It is recognized that depending on
accounting programs to copy MIB data during the job-retention
period is somewhat unreliable, since the accounting program
may not be running (or may have crashed). Such a program is
also expected to keep a shadow copy of the entire Job
Attribute table including completed, canceled, and aborted
jobs which the program updates on each polling cycle. Such a
program polls at the rate of the persistence of the Attribute
table. The design is not optimized to help such an
application determine which jobs are completed, canceled, or
aborted. Instead, the application SHOULD query each job that
the application's shadow copy shows was not complete,
canceled, or aborted at the previous poll cycle to see if it
is now complete or canceled, plus any new jobs that have been
submitted.
The MIB provides a set of objects that represent a compatible subset
of job and document attributes of the ISO DPA standard [iso-dpa] and
the Internet Printing Protocol (IPP) [ipp-model], so that coherence
is maintained between these two protocols and the information
presented to end users and system operators by monitoring
applications. However, the job monitoring MIB is intended to be used
with printers that implement other job submitting and management
protocols, such as IEEE 1284.1 (TIPSI) [tipsi], as well as with ones
that do implement ISO DPA. Thus the job monitoring MIB does not
require implementation of either the ISO DPA or IPP protocols.
The MIB is designed so that an additional MIB(s) can be specified in
the future for monitoring multi-function (scan, FAX, copy) jobs as an
augmentation to this MIB.
2 Terminology and Job Model
This section defines the terms that are used in this specification
and the general model for jobs in alphabetical order.
Bergman, et al. Informational [Page 7]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
NOTE - Existing systems use conflicting terms, so these terms are
drawn from the ISO 10175 Document Printing Application (DPA)
standard [iso-dpa]. For example, PostScript systems use the term
session for what is called a job in this specification and the
term job to mean what is called a document in this specification.
Accounting Application: The SNMP management application that copies
job information to some more permanent medium so that another
application can perform accounting on the data for Accountants, Asset
Managers, and Capacity Planners use.
Agent: The network entity that accepts SNMP requests from a monitor
or accounting application and provides access to the instrumentation
for managing jobs modeled by the management objects defined in the
Job Monitoring MIB module for a server or a device.
Attribute: A name, value-pair that specifies a job or document
instruction, a status, or a condition of a job or a document that has
been submitted to a server or device. A particular attribute NEED
NOT be present in each job instance. In other words, attributes are
present in a job instance only when there is a need to express the
value, either because (1) the client supplied a value in the job
submission protocol, (2) the document data contained an embedded
attribute, or (3) the server or device supplied a default value. An
agent MAY represent an attribute as an entry (row) in the Attribute
table in this MIB in which entries are present only when necessary.
Attributes are identified in this MIB by an enum.
Client: The network entity that end users use to submit jobs to
spoolers, servers, or printers and other devices, depending on the
configuration, using any job submission protocol over a serial or
parallel port to a directly-connected device or over the network to a
networked-connected device.
Device: A hardware entity that (1) interfaces to humans, such as a
device that produces marks on paper or scans marks on paper to
produce an electronic representation, (2) accesses digital media,
such as CD-ROMs, or (3) interfaces electronically to another device,
such as sends FAX data to another FAX device.
Document: A sub-section within a job that contains print data and
document instructions that apply to just the document.
Document Instruction: An instruction specifying how to process the
document. Document instructions MAY be passed in the job submission
protocol separate from the actual document data, or MAY be embedded
in the document data or a combination, depending on the job
submission protocol and implementation.
Bergman, et al. Informational [Page 8]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
End User: A user that uses a client to submit a print job. See
"user".
Impression: For a print job, an impression is the passage of the
entire side of a sheet by the marker, whether or not any marks are
made and independent of the number of passes that the side makes past
the marker. Thus a four pass color process counts as a single
impression, as does highlight color. Impression counters count all
kinds: monochrome, highlight color, and full process color, while
full color counters only count full color impressions, and high light
color counters only count high light color impressions.
One-sided processing involves one impression per sheet. Two-sided
processing involves two impressions per sheet. If a two-sided
document has an odd number of pages, the last sheet still counts as
two impressions, if that sheet makes two passes through the marker or
the marker marks on both sides of a sheet in a single pass. Two-up
printing is the placement of two logical pages on one side of a sheet
and so is still a single impression. See "page" and "sheet".
NOTE - Since impressions include blank sides, it is suggested that
accounting application implementers consider charging for sheets,
rather than impressions, possibly using the value of the sides
attribute to select different charges for one-sided versus two-sided
printing, since some users may think that impressions don't include
blank sides.
Internal Collation: The production of the sheets for each document
copy performed within the printing device by making multiple passes
over either the source or an intermediate representation of the
document.
Job: A unit of work whose results are expected together without
interjection of unrelated results. A job contains one or more
documents.
Job Accounting: The activity of a management application of
accessing the MIB and recording what happens to the job during and
after the processing of the job.
Job Instruction: An instruction specifying how, when, or where the
job is to be processed. Job instructions MAY be passed in the job
submission protocol or MAY be embedded in the document data or a
combination depending on the job submission protocol and
implementation.
Bergman, et al. Informational [Page 9]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
Job Monitoring (using SNMP): The activity of a management
application of accessing the MIB and (1) identifying jobs in the job
tables being processed by the server, printer or other devices, and
(2) displaying information to the user about the processing of the
job.
Job Monitoring Application: The SNMP management application that End
Users, and System Operators use to monitor jobs using SNMP. A
monitor MAY be either a separate application or MAY be part of the
client that also submits jobs. See "monitor".
Job Set: A group of jobs that are queued and scheduled together
according to a specified scheduling algorithm for a specified device
or set of devices. For implementations that embed the SNMP agent in
the device, the MIB job set normally represents all the jobs known to
the device, so that the implementation only implements a single job
set. If the SNMP agent is implemented in a server that controls one
or more devices, each MIB job set represents a job queue for (1) a
specific device or (2) set of devices, if the server uses a single
queue to load balance between several devices. Each job set is
disjoint; no job SHALL be represented in more than one MIB job set.
Monitor: Short for Job Monitoring Application.
Page: A page is a logical division of the original source document.
Number up is the imposition of more than one page on a single side of
a sheet. See "impression" and "sheet" and "two-up".
Proxy: An agent that acts as a concentrator for one or more other
agents by accepting SNMP operations on the behalf of one or more
other agents, forwarding them on to those other agents, gathering
responses from those other agents and returning them to the original
requesting monitor.
Queuing: The act of a device or server of ordering (queuing) the
jobs for the purposes of scheduling the jobs to be processed.
Printer: A device that puts marks on media.
Server: A network entity that accepts jobs from clients and in turn
submits the jobs to printers and other devices that may be directly
connected to the server via a serial or parallel port or may be on
the network. A server MAY be a printer supervisor control program,
or a print spooler.
Sheet: A sheet is a single instance of a medium, whether printing on
one or both sides of the medium. See "impression" and "page".
Bergman, et al. Informational [Page 10]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
SNMP Information Object: A name, value-pair that specifies an
action, a status, or a condition in an SNMP MIB. Objects are
identified in SNMP by an OBJECT IDENTIFIER.
Spooler: A server that accepts jobs, spools the data, and decides
when and on which printer to print the job. A spooler is a client to
a printer or a printer supervisor, depending on implementation.
Spooling: The act of a device or server of (1) accepting jobs and
(2) writing the job's attributes and document data on to secondary
storage.
Stacked: When a media sheet is placed in an output bin of a device.
Supervisor: A server that contains a control program that controls a
printer or other device. A supervisor is a client to the printer or
other device.
System Operator: A user that uses a monitor to monitor the system
and carries out tasks to keep the system running.
System Administrator: A user that specifies policy for the system.
Two-up: The placement of two pages on one side of a sheet so that
each side or impressions counts as two pages. See "page" and
"sheet".
User: A person that uses a client or a monitor. See "end user".
2.1 System Configurations for the Job Monitoring MIB
This section enumerates the three configurations in which the Job
Monitoring MIB is intended to be used. To simplify the pictures, the
devices are shown as printers. See section 1.1 entitled "Types of
Information in the MIB".
The diagram in the Printer MIB [print-mib] entitled: "One Printer's
View of the Network" is assumed for this MIB as well. Please refer
to that diagram to aid in understanding the following system
configurations.
2.1.1 Configuration 1 - client-printer
In the client-printer configuration 1, the client(s) submit jobs
directly to the printer, either by some direct connect, or by network
connection.
Bergman, et al. Informational [Page 11]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
The job submitting client and/or monitoring application monitor jobs
by communicating directly with an agent that is part of the printer.
The agent in the printer SHALL keep the job in the Job Monitoring MIB
as long as the job is in the printer, plus a defined time period
after the job enters the completed state in which accounting programs
can copy out the accounting data from the Job Monitoring MIB.
all end-user ######## SNMP query
+-------+ +--------+ ---- job submission
|monitor| | client |
+---#---+ +--#--+--+
# # |
# ############ |
# # |
+==+===#=#=+==+ |
| | agent | | |
| +-------+ | |
| PRINTER <--------+
| | Print Job Delivery Channel
| |
+=============+
Figure 2-1 - Configuration 1 - client-printer - agent in the printer
The Job Monitoring MIB is designed to support the following
relationships (not shown in Figure 2-1):
1. Multiple clients MAY submit jobs to a printer.
2. Multiple clients MAY monitor a printer.
3. Multiple monitors MAY monitor a printer.
4. A client MAY submit jobs to multiple printers.
5. A monitor MAY monitor multiple printers.
2.1.2 Configuration 2 - client-server-printer - agent in the server
In the client-server-printer configuration 2, the client(s) submit
jobs to an intermediate server by some network connection, not
directly to the printer. While configuration 2 is included, the
design center for this MIB is configurations 1 and 3.
The job submitting client and/or monitoring application monitor jobs
by communicating directly with:
A Job Monitoring MIB agent that is part of the server (or a front
for the server)
Bergman, et al. Informational [Page 12]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
There is no SNMP Job Monitoring MIB agent in the printer in
configuration 2, at least that the client or monitor are aware. In
this configuration, the agent SHALL return the current values of the
objects in the Job Monitoring MIB both for jobs the server keeps and
jobs that the server has submitted to the printer. The Job
Monitoring MIB agent obtains the required information from the
printer by a method that is beyond the scope of this document. The
agent in the server SHALL keep the job in the Job Monitoring MIB in
the server as long as the job is in the printer, plus a defined time
period after the job enters the completed state in which accounting
programs can copy out the accounting data from the Job Monitoring
MIB.
all end-user
+-------+ +----------+
|monitor| | client | ######## SNMP query
+---+---# +---#----+-+ **** non-SNMP cntrl
# # | ---- job submission
# # |
# # |
#=====#=+==v==+
| agent | |
+-------+ |
| server |
+----+-----+--+
control * |
********** |
* |
+========v====+ |
| | |
| | |
| PRINTER <---------+
| | Print Job Delivery Channel
| |
+=============+
Figure 2-2 - Configuration 2 - client-server-printer - agent in the
server
The Job Monitoring MIB is designed to support the following
relationships (not shown in Figure 2-2):
1. Multiple clients MAY submit jobs to a server.
2. Multiple clients MAY monitor a server.
3. Multiple monitors MAY monitor a server.
4. A client MAY submit jobs to multiple servers.
5. A monitor MAY monitor multiple servers.
6. Multiple servers MAY submit jobs to a printer.
7. Multiple servers MAY control a printer.
Bergman, et al. Informational [Page 13]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
2.1.3 Configuration 3 - client-server-printer - client monitors printer
agent and server
In the client-server-printer configuration 3, the client(s) submit
jobs to an intermediate server by some network connection, not
directly to the printer. That server does not contain a Job
Monitoring MIB agent.
The job submitting client and/or monitoring application monitor jobs
by communicating directly with:
1. The server using some undefined protocol to monitor jobs in
the server (that does not contain the Job Monitoring MIB) AND
2. A Job Monitoring MIB agent that is part of the printer to
monitor jobs after the server passes the jobs to the printer.
In such configurations, the server deletes its copy of the
job from the server after submitting the job to the printer
usually almost immediately (before the job does much
processing, if any).
In configuration 3, the agent (in the printer) SHALL keep the values
of the objects in the Job Monitoring MIB that the agent implements
updated for a job that the server has submitted to the printer. The
agent SHALL obtain information about the jobs submitted to the
printer from the server (either in the job submission protocol, in
the document data, or by direct query of the server), in order to
populate some of the objects the Job Monitoring MIB in the printer.
The agent in the printer SHALL keep the job in the Job Monitoring MIB
as long as the job is in the Printer, and longer in order to
implement the completed state in which monitoring programs can copy
out the accounting data from the Job Monitoring MIB.
Bergman, et al. Informational [Page 14]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
all end-user
+-------+ +----------+
|monitor| | client | ######## SNMP query
+---+---* +---*----+-+ **** non-SNMP query
# * * | ---- job submission
# * * |
# * * |
# *=====v====v==+
# | |
# | server |
# | |
# +----#-----+--+
# optional# |
# ########## |
# # |
+==+=v===v=+==+ |
| | agent | | |
| +-------+ | |
| PRINTER <---------+
| | Print Job Delivery Channel
| |
+=============+
Figure 2-3 - Configuration 3 - client-server-printer - client
monitors printer agent and server
The Job Monitoring MIB is designed to support the following
relationships (not shown in Figure 2-3):
1. Multiple clients MAY submit jobs to a server.
2. Multiple clients MAY monitor a server.
3. Multiple monitors MAY monitor a server.
4. A client MAY submit jobs to multiple servers.
5. A monitor MAY monitor multiple servers.
6. Multiple servers MAY submit jobs to a printer.
7. Multiple servers MAY control a printer.
3 Managed Object Usage
This section describes the usage of the objects in the MIB.
3.1 Conformance Considerations
In order to achieve interoperability between job monitoring
applications and job monitoring agents, this specification includes
the conformance requirements for both monitoring applications and
agents.
Bergman, et al. Informational [Page 15]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
3.1.1 Conformance Terminology
This specification uses the verbs: "SHALL", "SHOULD", "MAY", and
"NEED NOT" to specify conformance requirements according to RFC 2119
[RFC2119] as follows:
"SHALL": indicates an action that the subject of the sentence
must implement in order to claim conformance to this specification
"MAY": indicates an action that the subject of the sentence does
not have to implement in order to claim conformance to this
specification, in other words that action is an implementation
option
"NEED NOT": indicates an action that the subject of the sentence
does not have to implement in order to claim conformance to this
specification. The verb "NEED NOT" is used instead of "may not",
since "may not" sounds like a prohibition.
"SHOULD": indicates an action that is recommended for the subject
of the sentence to implement, but is not required, in order to
claim conformance to this specification.
3.1.2 Agent Conformance Requirements
A conforming agent:
1. SHALL implement all MANDATORY groups in this specification.
2. SHALL implement any attributes if (1) the server or device
supports the functionality represented by the attribute and (2)
the information is available to the agent.
3. SHOULD implement both forms of an attribute if it implements an
attribute that permits a choice of INTEGER and OCTET STRING
forms, since implementing both forms may help management
applications by giving them a choice of representations, since
the representation are equivalent. See the JmAttributeTypeTC
textual-convention.
NOTE - This MIB, like the Printer MIB, is written following the
subset of SMIv2 that can be supported by SMIv1 and SNMPv1
implementations.
Bergman, et al. Informational [Page 16]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
3.1.2.1 MIB II System Group objects
The Job Monitoring MIB agent SHALL implement all objects in the
System Group of MIB-II [mib-II], whether the Printer MIB [print-mib]
is implemented or not.
3.1.2.2 MIB II Interface Group objects
The Job Monitoring MIB agent SHALL implement all objects in the
Interfaces Group of MIB-II [mib-II], whether the Printer MIB [print-
mib] is implemented or not.
3.1.2.3 Printer MIB objects
If the agent is providing access to a device that is a printer, the
agent SHALL implement all of the MANDATORY objects in the Printer MIB
[print-mib] and all the objects in other MIBs that conformance to the
Printer MIB requires, such as the Host Resources MIB [hr-mib]. If
the agent is providing access to a server that controls one or more
direct-connect or networked printers, the agent NEED NOT implement
the Printer MIB and NEED NOT implement the Host Resources MIB.
3.1.3 Job Monitoring Application Conformance Requirements
A conforming job monitoring application:
1. SHALL accept the full syntactic range for all objects in all
MANDATORY groups and all MANDATORY attributes that are
required to be implemented by an agent according to Section
3.1.2 and SHALL either present them to the user or ignore
them.
2. SHALL accept the full syntactic range for all attributes,
including enum and bit values specified in this specification
and additional ones that may be registered with the PWG and
SHALL either present them to the user or ignore them. In
particular, a conforming job monitoring application SHALL not
malfunction when receiving any standard or registered enum or
bit values. See Section 3.7 entitled "IANA and PWG
Registration Considerations".
3. SHALL NOT fail when operating with agents that materialize
attributes after the job has been submitted, as opposed to
when the job is submitted.
4. SHALL, if it supports a time attribute, accept either form of
the time attribute, since agents are free to implement either
time form.
Bergman, et al. Informational [Page 17]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
3.2 The Job Tables and the Oldest Active and Newest Active Indexes
The jmJobTable and jmAttributeTable contain objects and attributes,
respectively, for each job in a job set. These first two indexes
are:
1. jmGeneralJobSetIndex - which job set
2. jmJobIndex - which job in the job set
In order for a monitoring application to quickly find that active
jobs (jobs in the pending, processing, or processingStopped states),
the MIB contains two indexes:
1. jmGeneralOldestActiveJobIndex - the index of the active job
that has been in the tables the longest.
2. jmGeneralNewestActiveJobIndex - the index of the active job
that has been most recently added to the tables.
The agent SHALL assign the next incremental value of jmJobIndex to
the job, when a new job is accepted by the server or device to which
the agent is providing access. If the incremented value of
jmJobIndex would exceed the implementation-defined maximum value for
jmJobIndex, the agent SHALL 'wrap' back to 1. An agent uses the
resulting value of jmJobIndex for storing information in the
jmJobTable and the jmAttributeTable about the job.
It is recommended that the largest value for jmJobIndex be much
larger than the maximum number of jobs that the implementation can
contain at a single time, so as to minimize the premature re-use of a
jmJobIndex value for a newer job while clients retain the same '
stale' value for an older job.
It is recommended that agents that are providing access to
servers/devices that already allocate job-identifiers for jobs as
integers use the same integer value for the jmJobIndex. Then
management applications using this MIB and applications using other
protocols will see the same job identifiers for the same jobs.
Agents providing access to systems that contain jobs with a job
identifier of 0 SHALL map the job identifier value 0 to a jmJobIndex
value that is one higher than the highest job identifier value that
any job can have on that system. Then only job 0 will have a
different job-identifier value than the job's jmJobIndex value.
NOTE - If a server or device accepts jobs using multiple job
submission protocols, it may be difficult for the agent to meet the
recommendation to use the job-identifier values that the server or
Bergman, et al. Informational [Page 18]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
device assigns as the jmJobIndex value, unless the server/device
assigns job-identifiers for each of its job submission protocols from
the same job-identifier number space.
Each time a new job is accepted by the server or device that the
agent is providing access to AND that job is to be 'active' (pending,
processing, or processingStopped, but not pendingHeld), the agent
SHALL copy the value of the job's jmJobIndex to the
jmGeneralNewestActiveJobIndex object. If the new job is to be '
inactive' (pendingHeld state), the agent SHALL not change the value
of jmGeneralNewestActiveJobIndex object (though the agent SHALL
assign the next incremental jmJobIndex value to the job).
When a job transitions from one of the 'active' job states (pending,
processing, processingStopped) to one of the 'inactive' job states
(pendingHeld, completed, canceled, or aborted), with a jmJobIndex
value that matches the jmGeneralOldestActiveJobIndex object, the
agent SHALL advance (or wrap) the value to the next oldest 'active'
job, if any. See the JmJobStateTC textual-convention for a
definition of the job states.
Whenever a job transitions from one of the 'inactive' job states to
one of the 'active' job states (from pendingHeld to pending or
processing), the agent SHALL update the value of either the
jmGeneralOldestActiveJobIndex or the jmGeneralNewestActiveJobIndex
objects, or both, if the job's jmJobIndex value is outside the range
between jmGeneralOldestActiveJobIndex and
jmGeneralNewestActiveJobIndex.
When all jobs become 'inactive', i.e., enter the pendingHeld,
completed, canceled, or aborted states, the agent SHALL set the value
of both the jmGeneralOldestActiveJobIndex and
jmGeneralNewestActiveJobIndex objects to 0.
NOTE - Applications that wish to efficiently access all of the active
jobs MAY use jmGeneralOldestActiveJobIndex value to start with the
oldest active job and continue until they reach the index value equal
to jmGeneralNewestActiveJobIndex, skipping over any pendingHeld,
completed, canceled, or aborted jobs that might intervene.
If an application detects that the jmGeneralNewestActiveJobIndex is
smaller than jmGeneralOldestActiveJobIndex, the job index has
wrapped. In this case, the application SHALL reset the index to 1
when the end of the table is reached and continue the GetNext
operations to find the rest of the active jobs.
Bergman, et al. Informational [Page 19]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
NOTE - Applications detect the end of the jmAttributeTable table when
the OID returned by the GetNext operation is an OID in a different
MIB. There is no object in this MIB that specifies the maximum value
for the jmJobIndex supported by the implementation.
When the server or device is power-cycled, the agent SHALL remember
the next jmJobIndex value to be assigned, so that new jobs are not
assigned the same jmJobIndex as recent jobs before the power cycle.
3.3 The Attribute Mechanism and the Attribute Table(s)
Attributes are similar to information objects, except that attributes
are identified by an enum, instead of an OID, so that attributes may
be registered without requiring a new MIB. Also an implementation
that does not have the functionality represented by the attribute can
omit the attribute entirely, rather than having to return a
distinguished value. The agent is free to materialize an attribute
in the jmAttributeTable as soon as the agent is aware of the value of
the attribute.
The agent materializes job attributes in a four-indexed
jmAttributeTable:
1. jmGeneralJobSetIndex - which job set
2. jmJobIndex - which job in the job set
3. jmAttributeTypeIndex - which attribute
4. jmAttributeInstanceIndex - which attribute instance for those
attributes that can have multiple values per job.
Some attributes represent information about a job, such as a file-
name, a document-name, a submission-time or a completion time. Other
attributes represent resources required, e.g., a medium or a
colorant, etc. to process the job before the job starts processing OR
to indicate the amount of the resource consumed during and after
processing, e.g., pages completed or impressions completed. If both
a required and a consumed value of a resource is needed, this
specification assigns two separate attribute enums in the textual
convention.
NOTE - The table of contents lists all the attributes in order. This
order is the order of enum assignments which is the order that the
SNMP GetNext operation returns attributes. Most attributes apply to
all three configurations covered by this MIB specification (see
Bergman, et al. Informational [Page 20]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
section 2.1 entitled "System Configurations for the Job Monitoring
MIB"). Those attributes that apply to a particular configuration are
indicated as 'Configuration n:' and SHALL NOT be used with other
configurations.
3.3.1 Conformance of Attribute Implementation
An agent SHALL implement any attribute if (1) the server or device
supports the functionality represented by the attribute and (2) the
information is available to the agent. The agent MAY create the
attribute row in the jmAttributeTable when the information is
available or MAY create the row earlier with the designated 'unknown'
value appropriate for that attribute. See next section.
If the server or device does not implement or does not provide access
to the information about an attribute, the agent SHOULD NOT create
the corresponding row in the jmAttributeTable.
3.3.2 Useful, 'Unknown', and 'Other' Values for Objects and Attributes
Some attributes have a 'useful' Integer32 value, some have a 'useful'
OCTET STRING value, some MAY have either or both depending on
implementation, and some MUST have both. See the JmAttributeTypeTC
textual convention for the specification of each attribute.
SNMP requires that if an object cannot be implemented because its
values cannot be accessed, then a compliant agent SHALL return an
SNMP error in SNMPv1 or an exception value in SNMPv2. However, this
MIB has been designed so that 'all' objects can and SHALL be
implemented by an agent, so that neither the SNMPv1 error nor the
SNMPv2 exception value SHALL be generated by the agent. This MIB has
also been designed so that when an agent materializes an attribute,
the agent SHALL materialize a row consisting of both the
jmAttributeValueAsInteger and jmAttributeValueAsOctets objects.
In general, values for objects and attributes have been chosen so
that a management application will be able to determine whether a '
useful', 'unknown', or 'other' value is available. When a useful
value is not available for an object, that agent SHALL return a
zero-length string for octet strings, the value 'unknown(2)' for
enums, a '0' value for an object that represents an index in another
table, and a value '-2' for counting integers.
Since each attribute is represented by a row consisting of both the
jmAttributeValueAsInteger and jmAttributeValueAsOctets MANDATORY
objects, SNMP requires that the agent SHALL always create an
attribute row with both objects specified. However, for most
attributes the agent SHALL return a "useful" value for one of the
Bergman, et al. Informational [Page 21]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
objects and SHALL return the 'other' value for the other object. For
integer only attributes, the agent SHALL always return a zero-length
string value for the jmAttributeValueAsOctets object. For octet
string only attributes, the agent SHALL always return a '-1' value
for the jmAttributeValueAsInteger object.
3.3.3 Index Value Attributes
A number of attributes are indexes in other tables. Such attribute
names end with the word 'Index'. If the agent has not (yet) assigned
an index value for a particular index attribute for a job, the agent
SHALL either: (1) return the value 0 or (2) not add this attribute to
the jmAttributeTable until the index value is assigned. In the
interests of brevity, the semantics for 0 is specified once here and
is not repeated for each index attribute specification and a DEFVAL
of 0 is implied, even though the DEFVAL for jmAttributeValueAsInteger
is -2.
3.3.4 Data Sub-types and Attribute Naming Conventions
Many attributes are sub-typed to give a more specific data type than
Integer32 or OCTET STRING. The data sub-type of each attribute is
indicated on the first line(s) of the description. Some attributes
have several different data sub-type representations. When an
attribute has both an Integer32 data sub-type and an OCTET STRING
data sub-type, the attribute can be represented in a single row in
the jmAttributeTable. In this case, the data sub-type name is not
included as the last part of the name of the attribute, e.g.,
documentFormat(38) which is both an enum and/or a name. When the
data sub-types cannot be represented by a single row in the
jmAttributeTable, each such representation is considered a separate
attribute and is assigned a separate name and enum value. For these
attributes, the name of the data sub-type is the last part of the
name of the attribute: Name, Index, DateAndTime, TimeStamp, etc. For
example, documentFormatIndex(37) is an index.
NOTE: The Table of Contents also lists the data sub-type and/or data
sub-types of each attribute, using the textual-convention name when
such is defined. The following abbreviations are used in the Table
of Contents as shown:
Bergman, et al. Informational [Page 22]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
'Int32(-2..)' Integer32 (-2..2147483647)
'Int32(0..)' Integer32 (0..2147483647)
'Int32(1..)' Integer32 (1..2147483647)
'Int32(m..n)' For all other Integer ranges, the lower
and upper bound of the range is
indicated.
'UTF8String63' JmUTF8StringTC (SIZE(0..63))
'JobString63' JmJobStringTC (SIZE(0..63))
'Octets63' OCTET STRING (SIZE(0..63))
'Octets(m..n)' For all other OCTET STRING ranges, the
exact range is indicated.
3.3.5 Single-Value (Row) Versus Multi-Value (MULTI-ROW) Attributes
Most attributes have only one row per job. However, a few attributes
can have multiple values per job or even per document, where each
value is a separate row in the jmAttributeTable. Unless indicated
with 'MULTI-ROW:' in the JmAttributeTypeTC description, an agent
SHALL ensure that each attribute occurs only once in the
jmAttributeTable for a job. Most of the 'MULTI-ROW' attributes do
not allow duplicate values, i.e., the agent SHALL ensure that each
value occurs only once for a job. Only if the specification of the '
MULTI-ROW' attribute also says "There is no restriction on the same
xxx occurring in multiple rows" can the agent allow duplicate values
to occur for the job.
NOTE - Duplicates are allowed for 'extensive' 'MULTI-ROW' attributes,
such as fileName(34) or documentName(35) which are specified to be '
per-document' attributes, but are not allowed for 'intensive' '
MULTI-ROW' attributes, such as mediumConsumed(171) and
documentFormat(38) which are specified to be 'per-job' attributes.
3.3.6 Requested Objects and Attributes
A number of objects and attributes record requirements for the job.
Such object and attribute names end with the word 'Requested'. In
the interests of brevity, the phrase 'requested' means: (1) requested
by the client (or intervening server) in the job submission protocol
and may also mean (2) embedded in the submitted document data, and/or
(3) defaulted by the recipient device or server with the same
semantics as if the requester had supplied, depending on
implementation. Also if a value is supplied by the job submission
client, and the server/device determines a better value, through
processing or other means, the agent MAY return that better value for
such object and attribute.
Bergman, et al. Informational [Page 23]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
3.3.7 Consumption Attributes
A number of objects and attributes record consumption. Such
attribute names end with the word 'Completed' or 'Consumed'. If the
job has not yet consumed what that resource is metering, the agent
either: (1) SHALL return the value 0 or (2) SHALL not add this
attribute to the jmAttributeTable until the consumption begins. In
the interests of brevity, the semantics for 0 is specified once here
and is not repeated for each consumption attribute specification and
a DEFVAL of 0 is implied, even though the DEFVAL for
jmAttributeValueAsInteger is -2.
3.3.8 Attribute Specifications
This section specifies the job attributes.
In the following definitions of the attributes, each description
indicates whether the useful value of the attribute SHALL be
represented using the jmAttributeValueAsInteger or the
jmAttributeValueAsOctets objects by the initial tag: 'INTEGER:' or '
OCTETS:', respectively.
Some attributes allow the agent implementer a choice of useful values
of either an integer, an octet string representation, or both,
depending on implementation. These attributes are indicated with '
INTEGER:' AND/OR 'OCTETS:' tags.
A very few attributes require both objects at the same time to
represent a pair of useful values (see mediumConsumed(171)). These
attributes are indicated with 'INTEGER:' AND 'OCTETS:' tags. See the
jmAttributeGroup for the descriptions of these two MANDATORY objects.
NOTE - The enum assignments are grouped logically with values
assigned in groups of 20, so that additional values may be registered
in the future and assigned a value that is part of their logical
grouping.
Values in the range 2**30 to 2**31-1 are reserved for private or
experimental usage. This range corresponds to the same range
reserved in IPP. Implementers are warned that use of such values may
conflict with other implementations. Implementers are encouraged to
request registration of enum values following the procedures in
Section 3.7.1.
NOTE: No attribute name exceeds 31 characters.
Bergman, et al. Informational [Page 24]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
The standard attribute types are:
jmAttributeTypeIndex Datatype
-------------------- --------
other(1), Integer32 (-2..2147483647)
AND/OR
OCTET STRING(SIZE(0..63))
INTEGER: and/or OCTETS: An attribute that is not in the
list and/or that has not been approved and registered with
the PWG.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+ Job State attributes (3 - 19 decimal)
+
+ The following attributes specify the state of a job.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
jobStateReasons2(3), JmJobStateReasons2TC
INTEGER: Additional information about the job's current state
that augments the jmJobState object. See the description under
the JmJobStateReasons1TC textual-convention.
jobStateReasons3(4), JmJobStateReasons3TC
INTEGER: Additional information about the job's current state
that augments the jmJobState object. See the description under
JmJobStateReasons1TC textual-convention.
jobStateReasons4(5), JmJobStateReasons4TC
INTEGER: Additional information about the job's current state
that augments the jmJobState object. See the description under
JmJobStateReasons1TC textual-convention.
processingMessage(6), JmUTF8StringTC (SIZE(0..63))
OCTETS: MULTI-ROW: A coded character set message that is
generated by the server or device during the processing of the
job as a simple form of processing log to show progress and any
problems. The natural language of each value is specified by
the corresponding processingMessageNaturalLangTag(7) value.
NOTE - This attribute is intended for such conditions as
interpreter messages, rather than being the printable form of
the jmJobState and jmJobStateReasons1 objects and
jobStateReasons2, jobStateReasons3, and jobStateReasons4
attributes. In order to produce a localized printable form of
these job state objects/attribute, a management application
SHOULD produce a message from their enum and bit values.
Bergman, et al. Informational [Page 25]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
NOTE - There is no job description attribute in IPP/1.0 that
corresponds to this attribute and this attribute does not
correspond to the IPP/1.0 'job-state-message' job description
attribute, which is just a printable form of the IPP 'job-state'
and 'job-state-reasons' job attributes.
There is no restriction for the same message occurring in
multiple rows.
processingMessageNaturalLangTag(7), OCTET STRING(SIZE(0..63))
OCTETS: MULTI-ROW: The natural language of the corresponding
processingMessage(6) attribute value. See section 3.6.1,
entitled 'Text generated by the server or device'.
If the agent does not know the natural language of the job
processing message, the agent SHALL either (1) return a zero
length string value for the processingMessageNaturalLangTag(7)
attribute or (2) not return the
processingMessageNaturalLangTag(7) attribute for the job.
There is no restriction for the same tag occurring in multiple
rows, since when this attribute is implemented, it SHOULD have a
value row for each corresponding processingMessage(6) attribute
value row.
jobCodedCharSet(8), CodedCharSet
INTEGER: The MIBenum identifier of the coded character set that
the agent is using to represent coded character set objects and
attributes of type 'JmJobStringTC'. These coded character set
objects and attributes are either: (1) supplied by the job
submitting client or (2) defaulted by the server or device when
omitted by the job submitting client. The agent SHALL represent
these objects and attributes in the MIB either (1) in the coded
character set as they were submitted or (2) MAY convert the
coded character set to another coded character set or encoding
scheme as identified by the jobCodedCharSet(8) attribute. See
section 3.6.2, entitled 'Text supplied by the job submitter'.
These MIBenum values are assigned by IANA [IANA-charsets] when
the coded character sets are registered. The coded character
set SHALL be one of the ones registered with IANA [IANA] and the
enum value uses the CodedCharSet textual-convention from the
Printer MIB. See the JmJobStringTC textual-convention.
If the agent does not know what coded character set was used by
the job submitting client, the agent SHALL either (1) return the
'unknown(2)' value for the jobCodedCharSet(8) attribute or (2)
not return the jobCodedCharSet(8) attribute for the job.
Bergman, et al. Informational [Page 26]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
jobNaturalLanguageTag(9), OCTET STRING(SIZE(0..63))
OCTETS: The natural language of the job attributes supplied by
the job submitter or defaulted by the server or device for the
job, i.e., all objects and attributes represented by the '
JmJobStringTC' textual-convention, such as jobName,
mediumRequested, etc. See Section 3.6.2, entitled 'Text
supplied by the job submitter'.
If the agent does not know what natural language was used by the
job submitting client, the agent SHALL either (1) return a zero
length string value for the jobNaturalLanguageTag(9) attribute
or (2) not return jobNaturalLanguageTag(9) attribute for the
job.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+ Job Identification attributes (20 - 49 decimal)
+
+ The following attributes help an end user, a system
+ operator, or an accounting program identify a job.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
jobURI(20), OCTET STRING(SIZE(0..63))
OCTETS: MULTI-ROW: The job's Universal Resource
Identifier (URI) [RFC1738]. See IPP [ipp-model] for
example usage.
NOTE - The agent may be able to generate this value on each
SNMP Get operation from smaller values, rather than having
to store the entire URI.
If the URI exceeds 63 octets, the agent SHALL use multiple
values, with the next 63 octets coming in the second value,
etc.
NOTE - IPP [ipp-model] has a 1023-octet maximum length for
a URI, though the URI standard itself and HTTP/1.1 specify
no maximum length.
jobAccountName(21), OCTET STRING(SIZE(0..63))
OCTETS: Arbitrary binary information which MAY be coded
character set data or encrypted data supplied by the
submitting user for use by accounting services to allocate
or categorize charges for services provided, such as a
customer account name or number.
NOTE: This attribute NEED NOT be printable characters.
Bergman, et al. Informational [Page 27]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
serverAssignedJobName(22), JmJobStringTC (SIZE(0..63))
OCTETS: Configuration 3 only: The human readable string
name, number, or ID of the job as assigned by the server
that submitted the job to the device that the agent is
providing access to with this MIB.
NOTE - This attribute is intended for enabling a user to
find his/her job that a server submitted to a device when
either the client does not support the jmJobSubmissionID or
the server does not pass the jmJobSubmissionID through to
the device.
jobName(23), JmJobStringTC (SIZE(0..63))
OCTETS: The human readable string name of the job as
assigned by the submitting user to help the user
distinguish between his/her various jobs. This name does
not need to be unique.
This attribute is intended for enabling a user or the
user's application to convey a job name that MAY be printed
on a start sheet, returned in a query result, or used in
notification or logging messages.
In order to assist users to find their jobs for job
submission protocols that don't supply a jmJobSubmissionID,
the agent SHOULD maintain the jobName attribute for the
time specified by the jmGeneralJobPersistence object,
rather than the (shorter) jmGeneralAttributePersistence
object.
If this attribute is not specified when the job is
submitted, no job name is assumed, but implementation
specific defaults are allowed, such as the value of the
documentName attribute of the first document in the job or
the fileName attribute of the first document in the job.
The jobName attribute is distinguished from the jobComment
attribute, in that the jobName attribute is intended to
permit the submitting user to distinguish between different
jobs that he/she has submitted. The jobComment attribute
is intended to be free form additional information that a
user might wish to use to communicate with himself/herself,
such as a reminder of what to do with the results or to
indicate a different set of input parameters were tried in
several different job submissions.
Bergman, et al. Informational [Page 28]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
jobServiceTypes(24), JmJobServiceTypesTC
INTEGER: Specifies the type(s) of service to which the job
has been submitted (print, fax, scan, etc.). The service
type is bit encoded with each job service type so that more
general and arbitrary services can be created, such as
services with more than one destination type, or ones with
only a source or only a destination. For example, a job
service might scan, faxOut, and print a single job. In
this case, three bits would be set in the jobServiceTypes
attribute, corresponding to the hexadecimal values: 0x8 +
0x20 + 0x4, respectively, yielding: 0x2C.
Whether this attribute is set from a job attribute supplied
by the job submission client or is set by the recipient job
submission server or device depends on the job submission
protocol. This attribute SHALL be implemented if the
server or device has other types in addition to or instead
of printing.
One of the purposes of this attribute is to permit a
requester to filter out jobs that are not of interest. For
example, a printer operator may only be interested in jobs
that include printing.
jobSourceChannelIndex(25), Integer32 (0..2147483647)
INTEGER: The index of the row in the associated Printer
MIB [print-mib] of the channel which is the source of the
print job.
jobSourcePlatformType(26), JmJobSourcePlatformTypeTC
INTEGER: The source platform type of the immediate
upstream submitter that submitted the job to the server
(configuration 2) or device (configuration 1 and 3) to
which the agent is providing access. For configuration 1,
this is the type of the client that submitted the job to
the device; for configuration 2, this is the type of the
client that submitted the job to the server; and for
configuration 3, this is the type of the server that
submitted the job to the device.
submittingServerName(27), JmJobStringTC (SIZE(0..63))
OCTETS: For configuration 3 only: The administrative name
of the server that submitted the job to the device.
submittingApplicationName(28), JmJobStringTC (SIZE(0..63))
OCTETS: The name of the client application (not the server
in configuration 3) that submitted the job to the server or
device.
Bergman, et al. Informational [Page 29]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
jobOriginatingHost(29), JmJobStringTC (SIZE(0..63))
OCTETS: The name of the client host (not the server host
name in configuration 3) that submitted the job to the
server or device.
deviceNameRequested(30), JmJobStringTC (SIZE(0..63))
OCTETS: The administratively defined coded character set
name of the target device requested by the submitting user.
For configuration 1, its value corresponds to the Printer
MIB [print-mib]: prtGeneralPrinterName object. For
configuration 2 and 3, its value is the name of the logical
or physical device that the user supplied to indicate to
the server on which device(s) they wanted the job to be
processed.
queueNameRequested(31), JmJobStringTC (SIZE(0..63))
OCTETS: The administratively defined coded character set
name of the target queue requested by the submitting user.
For configuration 1, its value corresponds to the queue in
the device for which the agent is providing access. For
configuration 2 and 3, its value is the name of the queue
that the user supplied to indicate to the server on which
device(s) they wanted the job to be processed.
NOTE - typically an implementation SHOULD support either
the deviceNameRequested or queueNameRequested attribute,
but not both.
physicalDevice(32), hrDeviceIndex
AND/OR
JmUTF8StringTC (SIZE(0..63))
INTEGER: MULTI-ROW: The index of the physical device MIB
instance requested/used, such as the Printer MIB [print-mib].
This value is an hrDeviceIndex value. See the Host
Resources MIB [hr-mib].
AND/OR
OCTETS: MULTI-ROW: The name of the physical device to
which the job is assigned.
numberOfDocuments(33), Integer32 (-2..2147483647)
INTEGER: The number of documents in this job.
The agent SHOULD return this attribute if the job has more
than one document.
Bergman, et al. Informational [Page 30]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
fileName(34), JmJobStringTC (SIZE(0..63))
OCTETS: MULTI-ROW: The coded character set file name or
URI [URI-spec] of the document.
There is no restriction on the same file name occurring in
multiple rows.
documentName(35), JmJobStringTC (SIZE(0..63))
OCTETS: MULTI-ROW: The coded character set name of the
document.
There is no restriction on the same document name occurring
in multiple rows.
jobComment(36), JmJobStringTC (SIZE(0..63))
OCTETS: An arbitrary human-readable coded character text
string supplied by the submitting user or the job
submitting application program for any purpose. For
example, a user might indicate what he/she is going to do
with the printed output or the job submitting application
program might indicate how the document was produced.
The jobComment attribute is not intended to be a name; see
the jobName attribute.
documentFormatIndex(37), Integer32 (0..2147483647)
INTEGER: MULTI-ROW: The index in the prtInterpreterTable
in the Printer MIB [print-mib] of the page description
language (PDL) or control language interpreter that this
job requires/uses. A document or a job MAY use more than
one PDL or control language.
NOTE - As with all intensive attributes where multiple rows
are allowed, there SHALL be only one distinct row for each
distinct interpreter; there SHALL be no duplicates.
NOTE - This attribute type is intended to be used with an
agent that implements the Printer MIB and SHALL not be used
if the agent does not implement the Printer MIB. Such an
agent SHALL use the documentFormat attribute instead.
Bergman, et al. Informational [Page 31]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
documentFormat(38), PrtInterpreterLangFamilyTC
AND/OR
OCTET STRING(SIZE(0..63))
INTEGER: MULTI-ROW: The interpreter language family
corresponding to the Printer MIB [print-mib]
prtInterpreterLangFamily object, that this job
requires/uses. A document or a job MAY use more than one
PDL or control language.
AND/OR
OCTETS: MULTI-ROW: The document format registered as a
media type [iana-media-types], i.e., the name of the MIME
content-type/subtype. Examples: 'application/postscript',
'application/vnd.hp-PCL', 'application/pdf', 'text/plain'
(US-ASCII SHALL be assumed), 'text/plain; charset=iso-8859-1',
and 'application/octet-stream'. The IPP 'document-format'
job attribute uses these same values with the same semantics.
See the IPP [ipp-model] 'mimeMediaType' attribute syntax and
the document-format attribute for further examples and
explanation.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+ Job Parameter attributes (50 - 67 decimal)
+
+ The following attributes represent input parameters
+ supplied by the submitting client in the job submission
+ protocol.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
jobPriority(50), Integer32 (-2..100)
INTEGER: The priority for scheduling the job. It is used by
servers and devices that employ a priority-based scheduling
algorithm.
A higher value specifies a higher priority. The value 1 is
defined to indicate the lowest possible priority (a job which a
priority-based scheduling algorithm SHALL pass over in favor of
higher priority jobs). The value 100 is defined to indicate the
highest possible priority. Priority is expected to be evenly or
'normally' distributed across this range. The mapping of
vendor-defined priority over this range is implementation-
specific. -2 indicates unknown.
jobProcessAfterDateAndTime(51), DateAndTime (SNMPv2-TC)
OCTETS: The calendar date and time of day after which the job
SHALL become a candidate to be scheduled for processing. If the
value of this attribute is in the future, the server SHALL set
Bergman, et al. Informational [Page 32]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
the value of the job's jmJobState object to pendingHeld and add
the jobProcessAfterSpecified bit value to the job's
jmJobStateReasons1 object. When the specified date and time
arrives, the server SHALL remove the jobProcessAfterSpecified
bit value from the job's jmJobStateReasons1 object and, if no
other reasons remain, SHALL change the job's jmJobState object
to pending.
jobHold(52), JmBooleanTC
INTEGER: If the value is 'true(4)', a client has explicitly
specified that the job is to be held until explicitly released.
Until the job is explicitly released by a client, the job SHALL
be in the pendingHeld state with the jobHoldSpecified value in
the jmJobStateReasons1 attribute.
jobHoldUntil(53), JmJobStringTC (SIZE(0..63))
OCTETS: The named time period during which the job SHALL become
a candidate for processing, such as 'evening', 'night', '
weekend', 'second-shift', 'third-shift', etc., (supported values
configured by the system administrator). See IPP [ipp-model]
for the standard keyword values. Until that time period
arrives, the job SHALL be in the pendingHeld state with the
jobHoldUntilSpecified value in the jmJobStateReasons1 object.
The value 'no-hold' SHALL indicate explicitly that no time
period has been specified; the absence of this attribute SHALL
indicate implicitly that no time period has been specified.
outputBin(54), Integer32 (0..2147483647)
AND/OR
JmJobStringTC (SIZE(0..63))
INTEGER: MULTI-ROW: The output subunit index in the Printer
MIB [print-mib]
AND/OR
OCTETS: MULTI-ROW: the name or number (represented as ASCII
digits) of the output bin to which all or part of the job is
placed in.
sides(55), Integer32 (-2..2)
INTEGER: MULTI-ROW: The number of sides, '1' or '2', that any
document in this job requires/used.
finishing(56), JmFinishingTC
INTEGER: MULTI-ROW: Type of finishing that any document in
this job requires/used.
Bergman, et al. Informational [Page 33]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+ Image Quality attributes (requested and consumed) (70 - 87)
+
+ For devices that can vary the image quality.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
printQualityRequested(70), JmPrintQualityTC
INTEGER: MULTI-ROW: The print quality selection requested for
a document in the job for printers that allow quality
differentiation.
printQualityUsed(71), JmPrintQualityTC
INTEGER: MULTI-ROW: The print quality selection actually used
by a document in the job for printers that allow quality
differentiation.
printerResolutionRequested(72), JmPrinterResolutionTC
OCTETS: MULTI-ROW: The printer resolution requested for a
document in the job for printers that support resolution
selection.
printerResolutionUsed(73), JmPrinterResolutionTC
OCTETS: MULTI-ROW: The printer resolution actually used by a
document in the job for printers that support resolution
selection.
tonerEcomonyRequested(74), JmTonerEconomyTC
INTEGER: MULTI-ROW: The toner economy selection requested for
documents in the job for printers that allow toner economy
differentiation.
tonerEcomonyUsed(75), JmTonerEconomyTC
INTEGER: MULTI-ROW: The toner economy selection actually used
by documents in the job for printers that allow toner economy
differentiation.
tonerDensityRequested(76) Integer32 (-2..100)
INTEGER: MULTI-ROW: The toner density requested for a document
in this job for devices that can vary toner density levels.
Level 1 is the lowest density and level 100 is the highest
density level. Devices with a smaller range, SHALL map the
1-100 range evenly onto the implemented range.
tonerDensityUsed(77), Integer32 (-2..100)
INTEGER: MULTI-ROW: The toner density used by documents in
this job for devices that can vary toner density levels. Level
Bergman, et al. Informational [Page 34]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
1 is the lowest density and level 100 is the highest density
level. Devices with a smaller range, SHALL map the 1-100 range
evenly onto the implemented range.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+ Job Progress attributes (requested and consumed) (90-109)
+
+ Pairs of these attributes can be used by monitoring
+ applications to show an indication of relative progress
+ to users. See section 3.4, entitled:
+ 'Monitoring Job Progress'.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
jobCopiesRequested(90), Integer32 (-2..2147483647)
INTEGER: The number of copies of the entire job that are to be
produced.
jobCopiesCompleted(91), Integer32 (-2..2147483647)
INTEGER: The number of copies of the entire job that have been
completed so far.
documentCopiesRequested(92), Integer32 (-2..2147483647)
INTEGER: The total count of the number of document copies
requested for the job as a whole. If there are documents A, B,
and C, and document B is specified to produce 4 copies, the
number of document copies requested is 6 for the job.
This attribute SHALL be used only when a job has multiple
documents. The jobCopiesRequested attribute SHALL be used when
the job has only one document.
documentCopiesCompleted(93), Integer32 (-2..2147483647)
INTEGER: The total count of the number of document copies
completed so far for the job as a whole. If there are documents
A, B, and C, and document B is specified to produce 4 copies,
the number of document copies starts a 0 and runs up to 6 for
the job as the job processes.
This attribute SHALL be used only when a job has multiple
documents. The jobCopiesCompleted attribute SHALL be used when
the job has only one document.
jobKOctetsTransferred(94), Integer32 (-2..2147483647)
INTEGER: The number of K (1024) octets transferred to the
server or device to which the agent is providing access. This
count is independent of the number of copies of the job or
documents that will be produced, but it is only a measure of the
number of bytes transferred to the server or device.
Bergman, et al. Informational [Page 35]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
The agent SHALL round the actual number of octets transferred up
to the next higher K. Thus 0 octets SHALL be represented as '
0', 1-1024 octets SHALL BE represented as '1', 1025-2048 SHALL
be '2', etc. When the job completes, the values of the
jmJobKOctetsPerCopyRequested object and the
jobKOctetsTransferred attribute SHALL be equal.
NOTE - The jobKOctetsTransferred can be used with the
jmJobKOctetsPerCopyRequested object in order to produce a
relative indication of the progress of the job for agents that
do not implement the jmJobKOctetsProcessed object.
sheetCompletedCopyNumber(95), Integer32 (-2..2147483647)
INTEGER: The number of the copy being stacked for the current
document. This number starts at 0, is set to 1 when the first
sheet of the first copy for each document is being stacked and
is equal to n where n is the nth sheet stacked in the current
document copy. See section 3.4 , entitled 'Monitoring Job
Progress'.
sheetCompletedDocumentNumber(96), Integer32 (-2..2147483647)
INTEGER: The ordinal number of the document in the job that is
currently being stacked. This number starts at 0, increments to
1 when the first sheet of the first document in the job is being
stacked, and is equal to n where n is the nth document in the
job, starting with 1.
Implementations that only support one document jobs SHOULD NOT
implement this attribute.
jobCollationType(97), JmJobCollationTypeTC
INTEGER: The type of job collation. See also Section 3.4,
entitled 'Monitoring Job Progress'.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+ Impression attributes (110 - 129 decimal)
+
+ See the definition of the terms 'impression', 'sheet',
+ and 'page' in Section 2.
+
+ See also jmJobImpressionsPerCopyRequested and
+ jmJobImpressionsCompleted objects in the jmJobTable.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
impressionsSpooled(110), Integer32 (-2..2147483647)
INTEGER: The number of impressions spooled to the server or
device for the job so far.
Bergman, et al. Informational [Page 36]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
impressionsSentToDevice(111), Integer32 (-2..2147483647)
INTEGER: The number of impressions sent to the device for the
job so far.
impressionsInterpreted(112), Integer32 (-2..2147483647)
INTEGER: The number of impressions interpreted for the job so
far.
impressionsCompletedCurrentCopy(113),
Integer32 (-2..2147483647)
INTEGER: The number of impressions completed by the device for
the current copy of the current document so far. For printing,
the impressions completed includes interpreting, marking, and
stacking the output. For other types of job services, the
number of impressions completed includes the number of
impressions processed.
This value SHALL be reset to 0 for each document in the job and
for each document copy.
fullColorImpressionsCompleted(114), Integer32 (-2..2147483647)
INTEGER: The number of full color impressions completed by the
device for this job so far. For printing, the impressions
completed includes interpreting, marking, and stacking the
output. For other types of job services, the number of
impressions completed includes the number of impressions
processed. Full color impressions are typically defined as those
requiring 3 or more colorants, but this MAY vary by
implementation. In any case, the value of this attribute counts
by 1 for each side that has full color, not by the number of
colors per side (and the other impression counters are
incremented, except highlightColorImpressionsCompleted(115)).
highlightColorImpressionsCompleted(115),
Integer32 (-2..2147483647)
INTEGER: The number of highlight color impressions
completed by the device for this job so far. For printing,
the impressions completed includes interpreting, marking,
and stacking the output. For other types of job services,
the number of impressions completed includes the number of
impressions processed. Highlight color impressions are
typically defined as those requiring black plus one other
colorant, but this MAY vary by implementation. In any
case, the value of this attribute counts by 1 for each side
that has highlight color (and the other impression counters
are incremented, except
fullColorImpressionsCompleted(114)).
Bergman, et al. Informational [Page 37]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+ Page attributes (130 - 149 decimal)
+
+ See the definition of 'impression', 'sheet', and 'page'
+ in Section 2.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
pagesRequested(130), Integer32 (-2..2147483647)
INTEGER: The number of logical pages requested by the job
to be processed.
pagesCompleted(131), Integer32 (-2..2147483647)
INTEGER: The number of logical pages completed for this
job so far.
For implementations where multiple copies are produced by
the interpreter with only a single pass over the data, the
final value SHALL be equal to the value of the
pagesRequested object. For implementations where multiple
copies are produced by the interpreter by processing the
data for each copy, the final value SHALL be a multiple of
the value of the pagesRequested object.
NOTE - See the impressionsCompletedCurrentCopy and
pagesCompletedCurrentCopy attributes for attributes that
are reset on each document copy.
NOTE - The pagesCompleted object can be used with the
pagesRequested object to provide an indication of the
relative progress of the job, provided that the
multiplicative factor is taken into account for some
implementations of multiple copies.
pagesCompletedCurrentCopy(132), Integer32 (-2..2147483647)
INTEGER: The number of logical pages completed for the
current copy of the document so far. This value SHALL be
reset to 0 for each document in the job and for each
document copy.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+ Sheet attributes (150 - 169 decimal)
+
+ See the definition of 'impression', 'sheet', and 'page'
+ in Section 2.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Bergman, et al. Informational [Page 38]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
sheetsRequested(150), Integer32 (-2..2147483647)
INTEGER: The total number of medium sheets requested to be
produced for this job.
Unlike the jmJobKOctetsPerCopyRequested and
jmJobImpressionsPerCopyRequested attributes, the
sheetsRequested(150) attribute SHALL include the
multiplicative factor contributed by the number of copies
and so is the total number of sheets to be produced by the
job, as opposed to the size of the document(s) submitted.
sheetsCompleted(151), Integer32 (-2..2147483647)
INTEGER: The total number of medium sheets that have
completed marking and stacking for the entire job so far
whether those sheets have been processed on one side or on
both.
sheetsCompletedCurrentCopy(152), Integer32 (-2..2147483647)
INTEGER: The number of medium sheets that have completed
marking and stacking for the current copy of a document in
the job so far whether those sheets have been processed on
one side or on both.
The value of this attribute SHALL be 0 before the job
starts processing and SHALL be reset to 1 after the first
sheet of each document and document copy in the job is
processed and stacked.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+ Resources attributes (requested and consumed) (170 - 189)
+
+ Pairs of these attributes can be used by monitoring
+ applications to show an indication of relative usage to
+ users, i.e., a 'thermometer'.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
mediumRequested(170), JmMediumTypeTC
AND/OR
JmJobStringTC (SIZE(0..63))
INTEGER: MULTI-ROW: The type
AND/OR
OCTETS: MULTI-ROW: the name of the medium that is
required by the job.
NOTE - The name (JmJobStringTC) values correspond to the
name values of the prtInputMediaName object in the Printer
MIB [print-mib] and the name, size, and input tray values
of the IPP 'media' attribute [ipp-model].
Bergman, et al. Informational [Page 39]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
mediumConsumed(171), Integer32 (-2..2147483647)
AND
JmJobStringTC (SIZE(0..63))
INTEGER: MULTI-ROW: The number of sheets
AND
OCTETS: MULTI-ROW: the name of the medium that has been
consumed so far whether those sheets have been processed on
one side or on both.
This attribute SHALL have both Integer32 and OCTET STRING
(represented as JmJobStringTC) values.
NOTE - The name (JmJobStringTC) values correspond to the
name values of the prtInputMediaName object in the Printer
MIB [print-mib] and the name, size, and input tray values
of the IPP 'media' attribute [ipp-model].
colorantRequested(172), Integer32 (-2..2147483647)
AND/OR
JmJobStringTC (SIZE(0..63))
INTEGER: MULTI-ROW: The index (prtMarkerColorantIndex) in
the Printer MIB [print-mib]
AND/OR
OCTETS: MULTI-ROW: the name of the colorant requested.
NOTE - The name (JmJobStringTC) values correspond to the
name values of the prtMarkerColorantValue object in the
Printer MIB. Examples are: red, blue.
colorantConsumed(173), Integer32 (-2..2147483647)
AND/OR
JmJobStringTC (SIZE(0..63))
INTEGER: MULTI-ROW: The index (prtMarkerColorantIndex) in
the Printer MIB [print-mib]
AND/OR
OCTETS: MULTI-ROW: the name of the colorant consumed.
NOTE - The name (JmJobStringTC) values correspond to the
name values of the prtMarkerColorantValue object in the
Printer MIB. Examples are: red, blue
Bergman, et al. Informational [Page 40]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
mediumTypeConsumed(174), Integer32 (-2..2147483647)
AND
JmJobStringTC (SIZE(0..63))
INTEGER: MULTI-ROW: The number of sheets of the indicated
medium type that has been consumed so far whether those
sheets have been processed on one side or on both
AND
OCTETS: MULTI-ROW: the name of that medium type.
This attribute SHALL have both Integer32 and OCTET STRING
(represented as JmJobStringTC) values.
NOTE - The type name (JmJobStringTC) values correspond to
the type name values of the prtInputMediaType object in the
Printer MIB [print-mib]. Values are: 'stationery',
'transparency', 'envelope', etc. These medium type names
correspond to the enum values of JmMediumTypeTC used in the
mediumRequested attribute.
mediumSizeConsumed(175), Integer32 (-2..2147483647)
AND
JmJobStringTC (SIZE(0..63))
INTEGER: MULTI-ROW: The number of sheets of the indicated
medium size that has been consumed so far whether those
sheets have been processed on one side or on both
AND
OCTETS: MULTI-ROW: the name of that medium size.
This attribute SHALL have both Integer32 and OCTET STRING
(represented as JmJobStringTC) values.
NOTE - The size name (JmJobStringTC) values correspond to
the size name values in the Printer MIB [print-mib]
Appendix B. These size name values are also a subset of
the keyword values defined by [ipp-model] for the 'media'
Job Template attribute. Values are: 'letter', 'a', 'iso-
a4', 'jis-b4', etc.
Bergman, et al. Informational [Page 41]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+ Time attributes (set by server or device) (190 - 209 decimal)
+
+ This section of attributes are ones that are set by the
+ server or device that accepts jobs. Two forms of time are
+ provided. Each form is represented in a separate attribute.
+ See section 3.1.2 and section 3.1.3 for the
+ conformance requirements for time attribute for agents and
+ monitoring applications, respectively. The two forms are:
+
+ 'DateAndTime' is an 8 or 11 octet binary encoded year,
+ month, day, hour, minute, second, deci-second with
+ optional offset from UTC. See SNMPv2-TC [SMIv2-TC].
+
+ NOTE: 'DateAndTime' is not printable characters; it is
+ binary.
+
+ 'JmTimeStampTC' is the time of day measured in the number of
+ seconds since the system was booted.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
jobSubmissionToServerTime(190), JmTimeStampTC
AND/OR
DateAndTime
INTEGER: Configuration 3 only: The time
AND/OR
OCTETS: the date and time that the job was submitted to
the server (as distinguished from the device which uses
jobSubmissionTime).
jobSubmissionTime(191), JmTimeStampTC
AND/OR
DateAndTime
INTEGER: Configurations 1, 2, and 3: The time
AND/OR
OCTETS: the date and time that the job was submitted to
the server or device to which the agent is providing
access.
jobStartedBeingHeldTime(192), JmTimeStampTC
AND/OR
DateAndTime
INTEGER: The time
AND/OR
OCTETS: the date and time that the job last entered the
pendingHeld state. If the job has never entered the
pendingHeld state, then the value SHALL be '0' or the
attribute SHALL not be present in the table.
Bergman, et al. Informational [Page 42]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
jobStartedProcessingTime(193), JmTimeStampTC
AND/OR
DateAndTime
INTEGER: The time
AND/OR
OCTETS: the date and time that the job started processing.
jobCompletionTime(194), JmTimeStampTC
AND/OR
DateAndTime
INTEGER: The time
AND/OR
OCTETS: the date and time that the job entered the
completed, canceled, or aborted state.
jobProcessingCPUTime(195) Integer32 (-2..2147483647)
UNITS 'seconds'
INTEGER: The amount of CPU time in seconds that the job
has been in the processing state. If the job enters the
processingStopped state, that elapsed time SHALL not be
included. In other words, the jobProcessingCPUTime value
SHOULD be relatively repeatable when the same job is
processed again on the same device.
3.3.9 Job State Reason bit definitions
The JmJobStateReasonsNTC (N=1..4) textual-conventions are used with
the jmJobStateReasons1 object and jobStateReasonsN (N=2..4),
respectively, to provide additional information regarding the current
jmJobState object value. These values MAY be used with any job state
or states for which the reason makes sense.
NOTE - While values cannot be added to the jmJobState object without
impacting deployed clients that take actions upon receiving
jmJobState values, it is the intent that additional
JmJobStateReasonsNTC enums can be defined and registered without
impacting such deployed clients. In other words, the
jmJobStateReasons1 object and jobStateReasonsN attributes are
intended to be extensible.
NOTE - The Job Monitoring MIB contains a superset of the IPP values
[ipp-model] for the IPP 'job-state-reasons' attribute, since the Job
Monitoring MIB is intended to cover other job submission protocols as
well. Also some of the names of the reasons have been changed from '
printer' to 'device', since the Job Monitoring MIB is intended to
cover additional types of devices, including input devices, such as
scanners.
Bergman, et al. Informational [Page 43]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
3.3.9.1 JmJobStateReasons1TC specification
The following standard values are defined (in hexadecimal) as powers
of two, since multiple values MAY be used at the same time. For ease
of understanding, the JmJobStateReasons1TC reasons are presented in
the order in which the reasons are likely to occur (if implemented),
starting with the 'jobIncoming' value and ending with the '
jobCompletedWithErrors' value.
other 0x1
The job state reason is not one of the standardized or
registered reasons.
unknown 0x2
The job state reason is not known to the agent or is
indeterminent.
jobIncoming 0x4
The job has been accepted by the server or device, but the
server or device is expecting (1) additional operations from the
client to finish creating the job and/or (2) is
accessing/accepting document data.
submissionInterrupted 0x8
The job was not completely submitted for some unforeseen reason,
such as: (1) the server has crashed before the job was closed by
the client, (2) the server or the document transfer method has
crashed in some non-recoverable way before the document data was
entirely transferred to the server, (3) the client crashed or
failed to close the job before the time-out period.
jobOutgoing 0x10
Configuration 2 only: The server is transmitting the job to the
device.
jobHoldSpecified 0x20
The value of the job's jobHold(52) attribute is TRUE. The job
SHALL NOT be a candidate for processing until this reason is
removed and there are no other reasons to hold the job.
jobHoldUntilSpecified 0x40
The value of the job's jobHoldUntil(53) attribute specifies a
time period that is still in the future. The job SHALL NOT be a
candidate for processing until this reason is removed and there
are no other reasons to hold the job.
Bergman, et al. Informational [Page 44]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
jobProcessAfterSpecified 0x80
The value of the job's jobProcessAfterDateAndTime(51) attribute
specifies a time that is still in the future. The job SHALL NOT
be a candidate for processing until this reason is removed and
there are no other reasons to hold the job.
resourcesAreNotReady 0x100
At least one of the resources needed by the job, such as media,
fonts, resource objects, etc., is not ready on any of the
physical devices for which the job is a candidate. This
condition MAY be detected when the job is accepted, or
subsequently while the job is pending or processing, depending
on implementation.
deviceStoppedPartly 0x200
One or more, but not all, of the devices to which the job is
assigned are stopped. If all of the devices are stopped (or the
only device is stopped), the deviceStopped reason SHALL be used.
deviceStopped 0x400
The device(s) to which the job is assigned is (are all) stopped.
jobInterpreting 0x800
The device to which the job is assigned is interpreting the
document data.
jobPrinting 0x1000
The output device to which the job is assigned is marking media.
This value is useful for servers and output devices which spend
a great deal of time processing (1) when no marking is happening
and then want to show that marking is now happening or (2) when
the job is in the process of being canceled or aborted while the
job remains in the processing state, but the marking has not yet
stopped so that impression or sheet counts are still increasing
for the job.
jobCanceledByUser 0x2000
The job was canceled by the owner of the job, i.e., by a user
whose name is the same as the value of the job's jmJobOwner
object, or by some other authorized end-user, such as a member
of the job owner's security group.
jobCanceledByOperator 0x4000
The job was canceled by the operator, i.e., by a user who has
been authenticated as having operator privileges (whether local
or remote).
Bergman, et al. Informational [Page 45]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
jobCanceledAtDevice 0x8000
The job was canceled by an unidentified local user, i.e., a user
at a console at the device.
abortedBySystem 0x10000
The job (1) is in the process of being aborted, (2) has been
aborted by the system and placed in the 'aborted' state, or (3)
has been aborted by the system and placed in the 'pendingHeld'
state, so that a user or operator can manually try the job
again.
processingToStopPoint 0x20000
The requester has issued an operation to cancel or interrupt the
job or the server/device has aborted the job, but the
server/device is still performing some actions on the job until
a specified stop point occurs or job termination/cleanup is
completed.
This reason is recommended to be used in conjunction with the
processing job state to indicate that the server/device is still
performing some actions on the job while the job remains in the
processing state. After all the job's resources consumed
counters have stopped incrementing, the server/device moves the
job from the processing state to the canceled or aborted job
states.
serviceOffLine 0x40000
The service or document transform is off-line and accepting no
jobs. All pending jobs are put into the pendingHeld state.
This situation could be true if the service's or document
transform's input is impaired or broken.
jobCompletedSuccessfully 0x80000
The job completed successfully.
jobCompletedWithWarnings 0x100000
The job completed with warnings.
jobCompletedWithErrors 0x200000
The job completed with errors (and possibly warnings too).
The following additional job state reasons have been added to
represent job states that are in ISO DPA [iso-dpa] and other job
submission protocols:
Bergman, et al. Informational [Page 46]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
jobPaused 0x400000
The job has been indefinitely suspended by a client issuing an
operation to suspend the job so that other jobs may proceed
using the same devices. The client MAY issue an operation to
resume the paused job at any time, in which case the agent SHALL
remove the jobPaused values from the job's jmJobStateReasons1
object and the job is eventually resumed at or near the point
where the job was paused.
jobInterrupted 0x800000 The job has been
interrupted while processing by a client
issuing an operation that specifies another job to be run
instead of the current job. The server or device will
automatically resume the interrupted job when the interrupting
job completes.
jobRetained 0x1000000
The job is being retained by the server or device with all of
the job's document data (and submitted resources, such as fonts,
logos, and forms, if any). Thus a client could issue an
operation to the server or device to either (1) re-do the job
(or a copy of the job) on the same server or device or (2)
resubmit the job to another server or device. When a client
could no longer re-do/resubmit the job, such as after the
document data has been discarded, the agent SHALL remove the
jobRetained value from the jmJobStateReasons1 object.
These bit definitions are the equivalent of a type 2 enum except
that combinations of bits may be used together. See section
3.7.1.2. The remaining bits are reserved for future
standardization and/or registration.
3.3.9.2 JmJobStateReasons2TC specification
The following standard values are defined (in hexadecimal) as powers
of two, since multiple values MAY be used at the same time.
cascaded 0x1
An outbound gateway has transmitted all of the job's job and
document attributes and data to another spooling system.
deletedByAdministrator 0x2
The administrator has deleted the job.
discardTimeArrived 0x4
The job has been deleted due to the fact that the time specified
by the job's job-discard-time attribute has arrived.
Bergman, et al. Informational [Page 47]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
postProcessingFailed 0x8
The post-processing agent failed while trying to log accounting
attributes for the job; therefore the job has been placed into
the completed state with the jobRetained jmJobStateReasons1
object value for a system-defined period of time, so the
administrator can examine it, resubmit it, etc.
jobTransforming 0x10
The server/device is interpreting document data and producing
another electronic representation.
maxJobFaultCountExceeded 0x20
The job has faulted several times and has exceeded the
administratively defined fault count limit.
devicesNeedAttentionTimeOut 0x40
One or more document transforms that the job is using needs
human intervention in order for the job to make progress, but
the human intervention did not occur within the site-settable
time-out value.
needsKeyOperatorTimeOut 0x80
One or more devices or document transforms that the job is using
need a specially trained operator (who may need a key to unlock
the device and gain access) in order for the job to make
progress, but the key operator intervention did not occur within
the site-settable time-out value.
jobStartWaitTimeOut 0x100
The server/device has stopped the job at the beginning of
processing to await human action, such as installing a special
cartridge or special non-standard media, but the job was not
resumed within the site-settable time-out value and the
server/device has transitioned the job to the pendingHeld state.
jobEndWaitTimeOut 0x200
The server/device has stopped the job at the end of processing
to await human action, such as removing a special cartridge or
restoring standard media, but the job was not resumed within the
site-settable time-out value and the server/device has
transitioned the job to the completed state.
jobPasswordWaitTimeOut 0x400
The server/device has stopped the job at the beginning of
processing to await input of the job's password, but the
password was not received within the site-settable time-out
value.
Bergman, et al. Informational [Page 48]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
deviceTimedOut 0x800
A device that the job was using has not responded in a period
specified by the device's site-settable attribute.
connectingToDeviceTimeOut 0x1000
The server is attempting to connect to one or more devices which
may be dial-up, polled, or queued, and so may be busy with
traffic from other systems, but server was unable to connect to
the device within the site-settable time-out value.
transferring 0x2000
The job is being transferred to a down stream server or
downstream device.
queuedInDevice 0x4000
The server/device has queued the job in a down stream server or
downstream device.
jobQueued 0x8000
The server/device has queued the document data.
jobCleanup 0x10000
The server/device is performing cleanup activity as part of
ending normal processing.
jobPasswordWait 0x20000
The server/device has selected the job to be next to process,
but instead of assigning resources and starting the job
processing, the server/device has transitioned the job to the
pendingHeld state to await entry of a password (and dispatched
another job, if there is one).
validating 0x40000
The server/device is validating the job after accepting the job.
queueHeld 0x80000
The operator has held the entire job set or queue.
jobProofWait 0x100000
The job has produced a single proof copy and is in the
pendingHeld state waiting for the requester to issue an
operation to release the job to print normally, obeying any job
and document copy attributes that were originally submitted.
heldForDiagnostics 0x200000
The system is running intrusive diagnostics, so that all jobs
are being held.
Bergman, et al. Informational [Page 49]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
noSpaceOnServer 0x800000
There is no room on the server to store all of the job.
pinRequired 0x1000000
The System Administrator settable device policy is (1) to
require PINs, and (2) to hold jobs that do not have a pin
supplied as an input parameter when the job was created.
exceededAccountLimit 0x2000000
The account for which this job is drawn has exceeded its limit.
This condition SHOULD be detected before the job is scheduled so
that the user does not wait until his/her job is scheduled only
to find that the account is overdrawn. This condition MAY also
occur while the job is processing either as processing begins or
part way through processing.
heldForRetry 0x4000000
The job encountered some errors that the server/device could not
recover from with its normal retry procedures, but the error
might not be encountered if the job is processed again in the
future. Example cases are phone number busy or remote file
system in-accessible. For such a situation, the server/device
SHALL transition the job from the processing to the pendingHeld,
rather than to the aborted state.
The following values are from the X/Open PSIS draft standard:
canceledByShutdown 0x8000000
The job was canceled because the server or device was shutdown
before completing the job.
deviceUnavailable 0x10000000
This job was aborted by the system because the device is
currently unable to accept jobs.
wrongDevice 0x20000000
This job was aborted by the system because the device is unable
to handle this particular job; the spooler SHOULD try another
device or the user should submit the job to another device.
badJob 0x40000000
This job was aborted by the system because this job has a major
problem, such as an ill-formed PDL; the spooler SHOULD not even
try another device.
These bit definitions are the equivalent of a type 2 enum except that
combinations of them may be used together. See section 3.7.1.2.
Bergman, et al. Informational [Page 50]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
3.3.9.3 JmJobStateReasons3TC specification
This textual-convention is used with the jobStateReasons3 attribute
to provides additional information regarding the jmJobState object.
The following standard values are defined (in hexadecimal) as powers
of two, since multiple values may be used at the same time:
jobInterruptedByDeviceFailure 0x1
A device or the print system software that the job was using has
failed while the job was processing. The server or device is
keeping the job in the pendingHeld state until an operator can
determine what to do with the job.
These bit definitions are the equivalent of a type 2 enum except that
combinations of them may be used together. See section 3.7.1.2. The
remaining bits are reserved for future standardization and/or
registration.
3.3.9.4 JmJobStateReasons4TC specification
This textual-convention is used with the jobStateReasons4 attribute
to provides additional information regarding the jmJobState object.
The following standard values are defined (in hexadecimal) as powers
of two, since multiple values MAY be used at the same time.
None defined at this time.
These bit definitions are the equivalent of a type 2 enum except that
combinations of them may be used together. See section 3.7.1.2. The
remaining bits are reserved for future standardization and/or
registration.
3.4 Monitoring Job Progress
There are a number of objects and attributes for monitoring the
progress of a job. These objects and attributes count the number of
K octets, impressions, sheets, and pages requested or completed. For
impressions and sheets, "completed" means stacked, unless the
implementation is unable to detect when each sheet is stacked, in
which case stacked is approximated when processing of each sheet
completes. There are objects and attributes for the overall job and
for the current copy of the document currently being stacked. For
the latter, the rate at which the various objects and attributes
count depends on the sheet and document collation of the job.
Bergman, et al. Informational [Page 51]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
Job Collation included sheet collation and document collation. Sheet
collation is defined to be the ordering of sheets within a document
copy. Document collation is defined to be ordering of document
copies within a multi-document job. There are three types of job
collation (see terminology definitions in Section 2):
1.uncollatedSheets(3) - No collation of the sheets within each
document copy, i.e., each sheet of a document that is to produce
multiple copies is replicated before the next sheet in the
document is processed and stacked. If the device has an output
bin collator, the uncollatedSheets(3) value may actually produce
collated sheets as far as the user is concerned (in the output
bins). However, when the job collation is the to a monitoring
application between a device that has an output bin collator and
one that does not.
2.collatedDocuments(4) - Collation of the sheets within each
document copy is performed within the printing device by making
multiple passes over either the source or an intermediate
representation of the document. In addition, when there are
multiple documents per job, the i'th copy of each document is
stacked before the j'th copy of each document, i.e., the
documents are collated within each job copy. For example, if a
job is submitted with documents, A and B, the job is made
available to the end user as: A, B, A, B, .... The '
collatedDocuments(4)' value corresponds to the IPP [ipp-model] '
separate-documents-collated-copies' value of the "multiple-
document-handling" attribute.
If jobCopiesRequested or documentCopiesRequested = 1, then
jobCollationType is defined as 4.
3.uncollatedDocuments(5) - Collation of the sheets within each
document copy is performed within the printing device by making
multiple passes over either the source or an intermediate
representation of the document. In addition, when there are
multiple documents per job, all copies of the first document in
the job are stacked before the any copied of the next document in
the job, i.e., the documents are uncollated within the job. For
example, if a job is submitted with documents, A and B, the job
is mad available to the end user as: A, A, ..., B, B, .... The
'uncollatedDocuments(5)' value corresponds to the IPP [ipp-model]
'separate-documents-uncollated-copies' value of the "multiple-
document-handling" attribute.
Consider the following four variables that are used to monitor the
progress of a job's impressions:
Bergman, et al. Informational [Page 52]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
1.jmJobImpressionsCompleted - counts the total number of
impressions stacked for the job
2.impressionsCompletedCurrentCopy - counts the number of
impressions stacked for the current document copy
3.sheetCompletedCopyNumber - identifies the number of the copy for
the current document being stacked where the first copy is 1.
4.sheetCompletedDocumentNumber - identifies the current document
within the job that is being stacked where the first document in
a job is 1. NOTE: this attribute SHOULD NOT be implemented for
implementations that only support one document per job.
For each of the three types of job collation, a job with three copies
of two documents (1, 2), where each document consists of 3
impressions, the four variables have the following values as each
sheet is stacked for one-sided printing:
Job Collation Type = uncollatedSheets(3)
jmJobImpressions Impressions sheetCompleted sheetCompleted
Completed CompletedCurrent CopyNumber DocumentNumber
Copy
0 0 0 0
1 1 1 1
2 1 2 1
3 1 3 1
4 2 1 1
5 2 2 1
6 2 3 1
7 3 1 1
8 3 2 1
9 3 3 1
10 1 1 2
11 1 2 2
12 1 3 2
13 2 1 2
14 2 2 2
15 2 3 2
16 3 1 2
17 3 2 2
18 3 3 2
Bergman, et al. Informational [Page 53]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
Job Collation Type = collatedDocuments(4)
JmJobImpressions Impressions sheetCompleted sheetCompleted
Completed CompletedCurrent CopyNumber DocumentNumber
Copy
0 0 0 0
1 1 1 1
2 2 1 1
3 3 1 1
4 1 1 2
5 2 1 2
6 3 1 2
7 1 2 1
8 2 2 1
9 3 2 1
10 1 2 2
11 2 2 2
12 3 2 2
13 1 3 1
14 2 3 1
15 3 3 1
16 1 3 2
17 2 3 2
18 3 3 2
Bergman, et al. Informational [Page 54]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
Job Collation Type = uncollatedDocuments(5)
jmJobImpressions Impressions sheetCompleted sheetCompleted
Completed CompletedCurrent CopyNumber DocumentNumber
Copy
0 0 0 0
1 1 1 1
2 2 1 1
3 3 1 1
4 1 2 1
5 2 2 1
6 3 2 1
7 1 3 1
8 2 3 1
9 3 3 1
10 1 1 2
11 2 1 2
12 3 1 2
13 1 2 2
14 2 2 2
15 3 2 2
16 1 3 2
17 2 3 2
18 3 3 2
3.5 Job Identification
There are a number of attributes that permit a user, operator or
system administrator to identify jobs of interest, such as jobURI,
jobName, jobOriginatingHost, etc. In addition, there is a
jmJobSubmissionID object that is a text string table index. Being a
table index allows a monitoring application to quickly locate and
identify a particular job of interest that was submitted from a
particular client by the user invoking the monitoring application
without having to scan the entire job table. The Job Monitoring MIB
needs to provide for identification of the job at both sides of the
job submission process. The primary identification point is the
client side. The jmJobSubmissionID allows the monitoring application
to identify the job of interest from all the jobs currently "known"
by the server or device. The value of jmJobSubmissionID can be
assigned by either the client's local system or a downstream server
or device. The point of assignment depends on the job submission
protocol in use.
Bergman, et al. Informational [Page 55]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
The server/device-side identifier, called the jmJobIndex object,
SHALL be assigned by the SNMP Job Monitoring MIB agent when the
server or device accepts the jobs from submitting clients. The
jmJobIndex object allows the interested party to obtain all objects
desired that relate to a particular job. See Section 3.2, entitled '
The Job Tables and the Oldest Active and Newest Active Indexes' for
the specification of how the agent SHALL assign the jmJobIndex
values.
The MIB provides a mapping table that maps each jmJobSubmissionID
value to a corresponding jmJobIndex value generated by the agent, so
that an application can determine the correct value for the
jmJobIndex value for the job of interest in a single Get operation,
given the Job Submission ID. See the jmJobIDGroup.
In some configurations there may be more than one application program
that monitors the same job when the job passes from one network
entity to another when it is submitted. See configuration 3. When
there are multiple job submission IDs, each entity MAY supply an
appropriate jmJobSubmissionID value. In this case there would be a
separate entry in the jmJobSubmissionID table, one for each
jmJobSubmissionID. All entries would map to the same jmJobIndex that
contains the job data. When the job is deleted, it is up to the
agent to remove all entries that point to the job from the
jmJobSubmissionID table as well.
The jobName attribute provides a name that the user supplies as a job
attribute with the job. The jobName attribute is not necessarily
unique, even for one user, let alone across users.
3.5.1 The Job Submission ID specifications
This section specifies the formats for each of the registered Job
Submission Ids. This format is used by the JmJobSubmissionIDTypeTC.
Each job submission ID is a fixed-length, 48-octet printable US-ASCII
[US-ASCII] coded character string containing no control characters,
consisting of the following fields:
octet 1: The format letter identifying the format. The
US-ASCII characters '0-9', 'A-Z', and 'a-z' are assigned
in order giving 62 possible formats.
octets 2-40: A 39-character, US-ASCII trailing SPACE
filled field specified by the format letter, if the data
is less than 39 ASCII characters.
octets 41-48: A sequential or random US-ASCII number to
make the ID quasi-unique.
Bergman, et al. Informational [Page 56]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
If the client does not supply a job submission ID in the job
submission protocol, then the agent SHALL assign a job submission ID
using any of the standard formats that are reserved for the agent.
Clients SHALL not use formats that are reserved for agents and agents
SHALL NOT use formats that are reserved for clients, in order to
reduce conflicts in ID generation. See the description for which
formats are reserved for clients or for agents.
Registration of additional formats may be done following the
procedures described in Section 3.7.3.
The format values defined at the time of completion of this
specification are:
Format
Letter Description
------ ------------
'0' Job Owner generated by the server/device
octets 2-40: The last 39 bytes of the jmJobOwner object.
octets 41-48: The US-ASCII 8-decimal-digit sequential number
assigned by the agent.
This format is reserved for agents.
NOTE - Clients wishing to use a job submission ID that
incorporates the job owner, SHALL use format '8', not
format '0'.
'1' Job Name
octets 2-40: The last 39 bytes of the jobName attribute.
octets 41-48: The US-ASCII 8-decimal-digit random number
assigned by the client.
This format is reserved for clients.
'2' Client MAC address
octets 2-40: The client MAC address: in hexadecimal with
each nibble of the 6 octet address being '0'-'9' or
'A' - 'F' (uppercase only). Most significant octet first.
octets 41-48: The US-ASCII 8-decimal-digit sequential number
assigned by the client.
This format is reserved for clients.
'3' Client URL
octets 2-40: The last 39 bytes of the client URL [URI-spec].
octets 41-48: The US-ASCII 8-decimal-digit sequential number
assigned by the client.
This format is reserved for clients.
Bergman, et al. Informational [Page 57]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
'4' Job URI
octets 2-40: The last 39 bytes of the URI [URI-spec]
assigned by the server or device to the job when the job
was submitted for processing.
octets 41-48: The US-ASCII 8-decimal-digit sequential number
assigned by the agent.
This format is reserved for agents.
'5' POSIX User Number
octets 2-40: The last 39 bytes of a user number, such as
POSIX user number.
octets 41-48: The US-ASCII 8-decimal-digit sequential number
assigned by the client.
This format is reserved for clients.
'6' User Account Number
octets 2-40: The last 39 bytes of the user account number.
octets 41-48: The US-ASCII 8-decimal-digit sequential number
assigned by the client.
This format is reserved for clients.
'7' DTMF Incoming FAX routing number
octets 2-40: The last 39 bytes of the DTMF incoming FAX
routing number.
octets 41-48: The US-ASCII 8-decimal-digit sequential number
assigned by the client.
This format is reserved for clients.
'8' Job Owner supplied by the client
octets 2-40: The last 39 bytes of the job owner name (that the
agent returns in the jmJobOwner object).
octets 41-48: The US-ASCII 8-decimal-digit sequential number
assigned by the client.
This format is reserved for clients. See format '0' which is
reserved for agents.
'9' Host Name
octets 2-40: The last 39 bytes of the host name with trailing
SPACES that submitted the job to this server/device using
a protocol, such as LPD [RFC1179] which includes the host
name in the job submission protocol.
octets 41-48: The US-ASCII 8-decimal-digit leading zero
representation of the job id generated by the submitting
server (configuration 3) or the client (configuration 1
and 2), such as in the LPD protocol.
This format is reserved for clients.
Bergman, et al. Informational [Page 58]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
'A' AppleTalk Protocol
octets 2-40: Contains the AppleTalk printer name, with the
first character of the name in octet 2. AppleTalk printer
names are a maximum of 31 characters. Any unused portion
of this field shall be filled with spaces.
octets 41-48: '00000XXX', where 'XXX' is the 3-digit US-ASCII
decimal representation of the Connection Id.
This format is reserved for agents.
'B' NetWare PServer
octets 2-40: Contains the Directory Path Name as recorded by
the Novell File Server in the queue directory. If the
string is less than 40 octets, the left-most character in
the string shall appear in octet position 2. Otherwise,
only the last 39 bytes shall be included. Any unused
portion of this field shall be filled with spaces.
octets 41-48: '000XXXXX' The US-ASCII representation of the
Job Number as per the NetWare File Server Queue Management
Services.
This format is reserved for agents.
'C' Server Message Block protocol (SMB)
octets 2-40: Contains a decimal (US-ASCII coded)
representation of the 16 bit SMB Tree Id field, which
uniquely identifies the connection that submitted the job
to the printer. The most significant digit of the numeric
string shall be placed in octet position 2. All unused
portions of this field shall be filled with spaces. The
SMB Tree Id has a maximum value of 65,535.
octets 41-48: The US-ASCII 8-decimal-digit leading zero
representation of the File Handle returned from the device
to the client in response to a Create Print File command.
This format is reserved for agents.
'D' Transport Independent Printer/System Interface (TIP/SI)
octets 2-40: Contains the Job Name from the Job Control-Start
Job (JC-SJ) command. If the Job Name portion is less than
40 octets, the left-most character in the string shall
appear in octet position 2. Any unused portion of this
field shall be filled with spaces. Otherwise, only the
last 39 bytes shall be included.
octets 41-48: The US-ASCII 8-decimal-digit leading zero
representation of the jmJobIndex assigned by the agent.
This format is reserved for agents, since the agent supplies
octets 41-48, though the client supplies the job name.
See format '1' reserved to clients to submit job name ids
in which they supply octets 41-48.
Bergman, et al. Informational [Page 59]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
'E' IPDS on the MVS or VSE platform
octets 2-40: Contains bytes 2-27 of the XOH Define Group
Boundary Group ID triplet. Octet position 2 MUST carry
the value x'01'. Bytes 28-40 MUST be filled with spaces.
octets 41-48: The US-ASCII 8-decimal-digit leading zero
representation of the jmJobIndex assigned by the agent.
This format is reserved for agents, since the agent supplies
octets 41-48, though the client supplies the job name.
'F' IPDS on the VM platform
octets 2-40: Contains bytes 2-31 of the XOH Define Group
Boundary Group ID triplet. Octet position 2 MUST carry
the value x'02'. Bytes 32-40 MUST be filled with spaces.
octets 41-48: The US-ASCII 8-decimal-digit leading zero
representation of the jmJobIndex assigned by the agent.
This format is reserved for agents, since the agent supplies
octets 41-48, though the client supplies the file name.
'G' IPDS on the OS/400 platform
octets 2-40: Contains bytes 2-36 of the XOH Define Group
Boundary Group ID triplet. Octet position 2 MUST carry
the value x'03'. Bytes 37-40 MUST be filled with spaces.
octets 41-48: The US-ASCII 8-decimal-digit leading zero
representation of the jmJobIndex assigned by the agent.
This format is reserved for agents, since the agent supplies
octets 41-48, though the client supplies the job name.
NOTE - the job submission id is only intended to be unique between a
limited set of clients for a limited duration of time, namely, for
the life time of the job in the context of the server or device that
is processing the job. Some of the formats include something that is
unique per client and a random number so that the same job submitted
by the same client will have a different job submission id. For
other formats, where part of the id is guaranteed to be unique for
each client, such as the MAC address or URL, a sequential number
SHOULD suffice for each client (and may be easier for each client to
manage). Therefore, the length of the job submission id has been
selected to reduce the probability of collision to an extremely low
number, but is not intended to be an absolute guarantee of
uniqueness. None-the-less, collisions are remotely possible, but
without bad consequences, since this MIB is intended to be used only
for monitoring jobs, not for controlling and managing them.
3.6 Internationalization Considerations
This section describes the internationalization considerations
included in this MIB.
Bergman, et al. Informational [Page 60]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
3.6.1 Text generated by the server or device
There are a few objects and attributes generated by the server or
device that SHALL be represented using the Universal Multiple-Octet
Coded Character Set (UCS) [ISO-10646]. These objects and attributes
are always supplied (if implemented) by the agent, not by the job
submitting client:
1. jmGeneralJobSetName object
2. processingMessage(6) attribute
3. physicalDevice(32) (name value) attribute
The character encoding scheme for representing these objects and
attributes SHALL be UTF-8 as REQUIRED by RFC 2277 [RFC2277]. The '
JmUTF8StringTC' textual convention is used to indicate UTF-8 text
strings.
NOTE - For strings in 7-bit US-ASCII, there is no impact since the
UTF-8 representation of 7-bit ASCII is identical to the US-ASCII
[US-ASCII] encoding.
The text contained in the processingMessage(6) attribute is generated
by the server/device. The natural language for the
processingMessage(6) attribute is identified by the
processingMessageNaturalLangTag(7) attribute. The
processingMessageNaturalLangTag(7) attribute uses the
JmNaturalLanguageTagTC textual convention which SHALL conform to the
language tag mechanism specified in RFC 1766 [RFC1766]. The
JmNaturalLanguageTagTC value is the same as the IPP [ipp-model] '
naturalLanguage' attribute syntax. RFC 1766 specifies that a US-
ASCII string consisting of the natural language followed by an
optional country field. Both fields use the same two-character codes
from ISO 639 [ISO-639] and ISO 3166 [ISO-3166], respectively, that
are used in the Printer MIB for identifying language and country.
Examples of the values of the processingMessageNaturalLangTag(7)
attribute include:
1. 'en' for English
2. 'en-us' for US English
3. 'fr' for French
4. 'de' for German
3.6.2 Text supplied by the job submitter
All of the objects and attributes represented by the 'JmJobStringTC'
textual-convention are either (1) supplied in the job submission
protocol by the client that submits the job to the server or device
or (2) are defaulted by the server or device if the job submitting
client does not supply values. The agent SHALL represent these
Bergman, et al. Informational [Page 61]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
objects and attributes in the MIB either (1) in the coded character
set as they were submitted or (2) MAY convert the coded character set
to another coded character set or encoding scheme. In any case, the
resulting coded character set representation SHOULD be UTF-8 [UTF-8],
but SHALL be one in which the code positions from 0 to 31 is not
used, 32 to 127 is US-ASCII [US-ASCII], 127 is not unused, and the
remaining code positions 128 to 255 represent single-byte or multi-
byte graphic characters structured according to ISO 2022 [ISO-2022]
or are unused.
The coded character set SHALL be one of the ones registered with IANA
[IANA] and SHALL be identified by the jobCodedCharSet attribute in
the jmJobAttributeTable for the job. If the agent does not know what
coded character set was used by the job submitting client, the agent
SHALL either (1) return the 'unknown(2)' value for the
jobCodedCharSet attribute or (2) not return the jobCodedCharSet
attribute for the job.
Examples of coded character sets which meet this criteria for use as
the value of the jobCodedCharSet job attribute are: US-ASCII [US-
ASCII], ISO 8859-1 (Latin-1) [ISO-8859-1], any ISO 8859-n, HP Roman8,
IBM Code Page 850, Windows Default 8-bit set, UTF-8 [UTF-8], US-ASCII
plus JIS X0208-1990 Japanese [JIS X0208], US-ASCII plus GB2312-1980
PRC Chinese [GB2312]. See the IANA registry of coded character sets
[IANA charsets].
Examples of coded character sets which do not meet this criteria are:
national 7-bit sets conforming to ISO 646 (except US-ASCII), EBCDIC,
and ISO 10646 (Unicode) [ISO-10646]. In order to represent Unicode
characters, the UTF-8 [UTF-8] encoding scheme SHALL be used which has
been assigned the MIBenum value of '106' by IANA.
The jobCodedCharSet attribute uses the imported 'CodedCharSet'
textual-convention from the Printer MIB [printmib].
The natural language for attributes represented by the textual-
convention JmJobStringTC is identified either (1) by the
jobNaturalLanguageTag(9) attribute or is keywords in US-English (as
in IPP). A monitoring application SHOULD attempt to localize
keywords into the language of the user by means of some lookup
mechanism. If the keyword value is not known to the monitoring
application, the monitoring application SHOULD assume that the value
is in the natural language specified by the job's
jobNaturalLanguageTag(9) attribute and SHOULD present the value to
its user as is. The jobNaturalLanguageTag(9) attribute value SHALL
have the same syntax and semantics as the
processingMessageNaturalLangTag(7) attribute, except that the
jobNaturalLanguageTag(9) attribute identifies the natural language of
Bergman, et al. Informational [Page 62]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
attributes supplied by the job submitter instead of the natural
language of the processingMessage(6) attribute. See Section 3.6.1.
3.6.3 'DateAndTime' for representing the date and time
This MIB also contains objects that are represented using the
DateAndTime textual convention from SMIv2 [SMIv2-TC]. The job
management application SHALL display such objects in the locale of
the user running the monitoring application.
3.7 IANA and PWG Registration Considerations
This MIB does not require any additional registration schemes for
IANA, but does depend on registration schemes that other Internet
standards track specifications have set up. The names of these IANA
registration assignments under the /in-notes/iana/assignments/ path:
1.printer-language-numbers - used as enums in the documentFormat(38)
attribute
2.media-types - uses as keywords in the documentFormat(38) attribute
3.character-sets - used as enums in the jobCodedCharSet(8) attribute
The Printer Working Group (PWG) will handle registration of
additional enums after approving this standard, according to the
procedures described in this section:
3.7.1 PWG Registration of enums
This specification uses textual conventions to define enumerated
values (enums) and bit values. Enumerations (enums) and bit values
are sets of symbolic values defined for use with one or more objects
or attributes. All enumeration sets and bit value sets are assigned
a symbolic data type name (textual convention). As a convention the
symbolic name ends in "TC" for textual convention. These
enumerations are defined at the beginning of the MIB module
specification.
The PWG has defined several type of enumerations for use in the Job
Monitoring MIB and the Printer MIB [print-mib]. These types differ
in the method employed to control the addition of new enumerations.
Throughout this document, references to "type n enum", where n can be
1, 2 or 3 can be found in the various tables. The definitions of
these types of enumerations are:
Bergman, et al. Informational [Page 63]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
3.7.1.1 Type 1 enumerations
Type 1 enumeration: All the values are defined in the Job Monitoring
MIB specification (RFC for the Job Monitoring MIB). Additional
enumerated values require a new RFC.
There are no type 1 enums in the current document.
3.7.1.2 Type 2 enumerations
Type 2 enumeration: An initial set of values are defined in the Job
Monitoring MIB specification. Additional enumerated values are
registered with the PWG.
The following type 2 enums are contained in the current document:
1. JmUTF8StringTC
2. JmJobStringTC
3. JmNaturalLanguageTagTC
4. JmTimeStampTC
5. JmFinishingTC [same enum values as IPP "finishing" attribute]
6. JmPrintQualityTC [same enum values as IPP "print-quality"
attribute]
7. JmTonerEconomyTC
8. JmMediumTypeTC
9. JmJobSubmissionIDTypeTC
10.JmJobCollationTypeTC
11.JmJobStateTC [same enum values as IPP "job-state" attribute]
12.JmAttributeTypeTC
For those textual conventions that have the same enum values as the
indicated IPP Job attribute are simultaneously registered by the PWG
for use with IPP [ipp-model] and the Job Monitoring MIB.
3.7.1.3 Type 3 enumeration
Type 3 enumeration: An initial set of values are defined in the Job
Monitoring MIB specification. Additional enumerated values are
registered through the PWG without PWG review.
There are no type 3 enums in the current document.
Bergman, et al. Informational [Page 64]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
3.7.2 PWG Registration of type 2 bit values
This memo contains the following type 2 bit value textual-
conventions:
1. JmJobServiceTypesTC
2. JmJobStateReasons1TC
3. JmJobStateReasons2TC
4. JmJobStateReasons3TC
5. JmJobStateReasons4TC
These textual-conventions are defined as bits in an Integer so that
they can be used with SNMPv1 SMI. The jobStateReasonsN (N=1..4)
attributes are defined as bit values using the corresponding
JmJobStateReasonsNTC textual-conventions.
The registration of JmJobServiceTypesTC and JmJobStateReasonsNTC bit
values follow the procedures for a type 2 enum as specified in
Section 3.7.1.2.
3.7.3 PWG Registration of Job Submission Id Formats
In addition to enums and bit values, this specification assigns a
single ASCII digit or letter to various job submission ID formats.
See the JmJobSubmissionIDTypeTC textual-convention and the object.
The registration of JobSubmissionID format numbers follows the
procedures for a type 2 enum as specified in Section 3.7.1.2.
3.7.4 PWG Registration of MIME types/sub-types for document-formats
The documentFormat(38) attribute has MIME type/sub-type values for
indicating document formats which IANA registers as "media type"
names. The values of the documentFormat(38) attribute are the same
as the corresponding Internet Printing Protocol (IPP) "document-
format" Job attribute values [ipp-model].
3.8 Security Considerations
3.8.1 Read-Write objects
All objects are read-only, greatly simplifying the security
considerations. If another MIB augments this MIB, that MIB might
accept SNMP Write operations to objects in that MIB whose effect is
to modify the values of read-only objects in this MIB. However, that
MIB SHALL have to support the required access control in order to
achieve security, not this MIB.
Bergman, et al. Informational [Page 65]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
3.8.2 Read-Only Objects In Other User's Jobs
The security policy of some sites MAY be that unprivileged users can
only get the objects from jobs that they submitted, plus a few
minimal objects from other jobs, such as the
jmJobKOctetsPerCopyRequested and jmJobKOctetsProcessed objects, so
that a user can tell how busy a printer is. Other sites MAY allow
all unprivileged users to see all objects of all jobs. This MIB does
not require, nor does it specify how, such restrictions would be
implemented. A monitoring application SHOULD enforce the site
security policy with respect to returning information to an
unprivileged end user that is using the monitoring application to
monitor jobs that do not belong to that user, i.e., the jmJobOwner
object in the jmJobTable does not match the user's user name.
An operator is a privileged user that would be able to see all
objects of all jobs, independent of the policy for unprivileged
users.
3.9 Notifications
This MIB does not specify any notifications. For simplicity,
management applications are expected to poll for status. The
jmGeneralJobPersistence and jmGeneralAttributePersistence objects
assist an application to determine the polling rate. The resulting
network traffic is not expected to be significant.
Bergman, et al. Informational [Page 66]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
4 MIB specification
The following pages constitute the actual Job Monitoring MIB.
Job-Monitoring-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, enterprises,
Integer32 FROM SNMPv2-SMI
TEXTUAL-CONVENTION FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF;
-- The following textual-conventions are needed to implement
-- certain attributes, but are not needed to compile this MIB.
-- They are provided here for convenience:
-- hrDeviceIndex FROM HOST-RESOURCES-MIB
-- DateAndTime FROM SNMPv2-TC
-- PrtInterpreterLangFamilyTC,
-- CodedCharSet FROM Printer-MIB
-- Use the enterprises arc assigned to the PWG which is pwg(2699).
-- Group all PWG mibs under mibs(1).
jobmonMIB MODULE-IDENTITY
LAST-UPDATED "9902190000Z"
ORGANIZATION "Printer Working Group (PWG)"
CONTACT-INFO
"Tom Hastings
Postal: Xerox Corp.
Mail stop ESAE-231
701 S. Aviation Blvd.
El Segundo, CA 90245
Tel: (301)333-6413
Fax: (301)333-5514
E-mail: hastings@cp10.es.xerox.com
Send questions and comments to the Printer Working Group (PWG)
using the Job Monitoring Project (JMP) Mailing List:
jmp@pwg.org
For further information, including how to subscribe to the
jmp mailing list, access the PWG web page under 'JMP':
http://www.pwg.org/
Implementers of this specification are encouraged to join the
jmp mailing list in order to participate in discussions on any
clarifications needed and registration proposals being reviewed
Bergman, et al. Informational [Page 67]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
in order to achieve consensus."
DESCRIPTION
"The MIB module for monitoring job in servers, printers, and
other devices.
Version: 1.0"
-- revision history
REVISION "9902190000Z"
DESCRIPTION " This version published as RFC 2707"
::= { enterprises pwg(2699) mibs(1) jobmonMIB(1) }
-- Textual conventions for this MIB module
JmUTF8StringTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "255a"
STATUS current
DESCRIPTION
"To facilitate internationalization, this TC represents
information taken from the ISO/IEC IS 10646-1 character set,
encoded as an octet string using the UTF-8 character encoding
scheme.
See section 3.6.1, entitled: 'Text generated by the server or
device'."
SYNTAX OCTET STRING (SIZE (0..63))
JmJobStringTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"To facilitate internationalization, this TC represents
information using any coded character set registered by IANA as
specified in section 3.7. While it is recommended that the
coded character set be UTF-8 [UTF-8], the actual coded
character set SHALL be indicated by the value of the
jobCodedCharSet(8) attribute for the job.
See section 3.6.2, entitled: 'Text supplied by the job
submitter'."
SYNTAX OCTET STRING (SIZE (0..63))
Bergman, et al. Informational [Page 68]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
JmNaturalLanguageTagTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"An IETF RFC 1766-compliant 'language tag', with zero or more
sub-tags that identify a natural language. While RFC 1766
specifies that the US-ASCII values are case-insensitive, this
MIB specification requires that all characters SHALL be lower
case in order to simplify comparing by management applications.
See section 3.6.1, entitled: 'Text generated by the server or
device' and section 3.6.2, entitled: 'Text supplied by the job
submitter'."
SYNTAX OCTET STRING (SIZE (0..63))
JmTimeStampTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The simple time at which an event took place. The units are
in seconds since the system was booted.
NOTE - JmTimeStampTC is defined in units of seconds, rather
than 100ths of seconds, so as to be simpler for agents to
implement (even if they have to implement the 100ths of a
second to comply with implementing sysUpTime in MIB-II[mib-
II].)
NOTE - JmTimeStampTC is defined as an Integer32 so that it can
be used as a value of an attribute, i.e., as a value of the
jmAttributeValueAsInteger object. The TimeStamp textual-
convention defined in SNMPv2-TC [SMIv2-TC] is defined as an
APPLICATION 3 IMPLICIT INTEGER tag, not an Integer32 which is
defined in SNMPv2-SMI [SMIv2-TC] as UNIVERSAL 2 IMPLICIT
INTEGER, so cannot be used in this MIB as one of the values of
jmAttributeValueAsInteger."
SYNTAX INTEGER (0..2147483647)
JmJobSourcePlatformTypeTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The source platform type that can submit jobs to servers or
devices in any of the 3 configurations.
This is a type 2 enumeration. See Section 3.7.1.2. See also
Bergman, et al. Informational [Page 69]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
IANA operating-system-names registry."
SYNTAX INTEGER {
other(1),
unknown(2),
sptUNIX(3), -- UNIX
sptOS2(4), -- OS/2
sptPCDOS(5), -- DOS
sptNT(6), -- NT
sptMVS(7), -- MVS
sptVM(8), -- VM
sptOS400(9), -- OS/400
sptVMS(10), -- VMS
sptWindows(11), -- Windows
sptNetWare(12) -- NetWare
}
JmFinishingTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The type of finishing operation.
These values are the same as the enum values of the IPP
'finishings' attribute. See Section 3.7.1.2.
other(1),
Some other finishing operation besides one of the specified
or registered values.
unknown(2),
The finishing is unknown.
none(3),
Perform no finishing.
staple(4),
Bind the document(s) with one or more staples. The exact
number and placement of the staples is site-defined.
punch(5),
Holes are required in the finished document. The exact
number and placement of the holes is site-defined. The
punch specification MAY be satisfied (in a site- and
implementation-specific manner) either by
drilling/punching, or by substituting pre-drilled media.
cover(6),
Bergman, et al. Informational [Page 70]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
Select a non-printed (or pre-printed) cover for the
document. This does not supplant the specification of a
printed cover (on cover stock medium) by the document
itself.
bind(7)
Binding is to be applied to the document; the type and
placement of the binding is product-specific.
This is a type 2 enumeration. See Section 3.7.1.2."
SYNTAX INTEGER {
other(1),
unknown(2),
none(3),
staple(4),
punch(5),
cover(6),
bind(7)
}
JmPrintQualityTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Print quality settings.
These values are the same as the enum values of the IPP 'print-
quality' attribute. See Section 3.7.1.2.
This is a type 2 enumeration. See Section 3.7.1.2."
SYNTAX INTEGER {
other(1), -- Not one of the specified or registered
-- values.
unknown(2), -- The actual value is unknown.
draft(3), -- Lowest quality available on the printer.
normal(4), -- Normal or intermediate quality on the
-- printer.
high(5) -- Highest quality available on the printer.
}
JmPrinterResolutionTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Printer resolutions.
Nine octets consisting of two 4-octet SIGNED-INTEGERs followed
Bergman, et al. Informational [Page 71]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
by a SIGNED-BYTE. The values are the same as those specified
in the Printer MIB [printmib]. The first SIGNED-INTEGER
contains the value of prtMarkerAddressabilityXFeedDir. The
second SIGNED-INTEGER contains the value of
prtMarkerAddressabilityFeedDir. The SIGNED-BYTE contains the
value of prtMarkerAddressabilityUnit.
Note: the latter value is either 3 (tenThousandsOfInches) or 4
(micrometers) and the addressability is in 10,000 units of
measure. Thus the SIGNED-INTEGERs represent integral values in
either dots-per-inch or dots-per-centimeter.
The syntax is the same as the IPP 'printer-resolution'
attribute. See Section 3.7.1.2."
SYNTAX OCTET STRING (SIZE(9))
JmTonerEconomyTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Toner economy settings.
This is a type 2 enumeration. See Section 3.7.1.2."
SYNTAX INTEGER {
unknown(2), -- unknown.
off(3), -- Off. Normal. Use full toner.
on(4) -- On. Use less toner than normal.
}
JmBooleanTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Boolean true or false value.
This is a type 2 enumeration. See Section 3.7.1.2."
SYNTAX INTEGER {
unknown(2), -- unknown.
false(3), -- FALSE.
true(4) -- TRUE.
}
JmMediumTypeTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
Bergman, et al. Informational [Page 72]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
"Identifies the type of medium.
other(1),
The type is neither one of the values listed in this
specification nor a registered value.
unknown(2),
The type is not known.
stationery(3),
Separately cut sheets of an opaque material.
transparency(4),
Separately cut sheets of a transparent material.
envelope(5),
Envelopes that can be used for conventional mailing
purposes.
envelopePlain(6),
Envelopes that are not preprinted and have no windows.
envelopeWindow(7),
Envelopes that have windows for addressing purposes.
continuousLong(8),
Continuously connected sheets of an opaque material
connected along the long edge.
continuousShort(9),
Continuously connected sheets of an opaque material
connected along the short edge.
tabStock(10),
Media with tabs.
multiPartForm(11),
Form medium composed of multiple layers not pre-attached to
one another; each sheet MAY be drawn separately from an
input source.
labels(12),
Label-stock.
multiLayer(13)
Form medium composed of multiple layers which are pre-
attached to one another, e.g. for use with impact printers.
Bergman, et al. Informational [Page 73]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
This is a type 2 enumeration. See Section 3.7.1.2. These enum
values correspond to the keyword name strings of the
prtInputMediaType object in the Printer MIB [print-mib]. There
is no printer description attribute in IPP/1.0 that represents
these values."
SYNTAX INTEGER {
other(1),
unknown(2),
stationery(3),
transparency(4),
envelope(5),
envelopePlain(6),
envelopeWindow(7),
continuousLong(8),
continuousShort(9),
tabStock(10),
multiPartForm(11),
labels(12),
multiLayer(13)
}
JmJobCollationTypeTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This value is the type of job collation. Implementations that
don't support multiple documents or don't support multiple
copies SHALL NOT support the uncollatedDocuments(5) value.
This is a type 2 enumeration. See Section 3.7.1.2. See also
Section 3.4, entitled 'Monitoring Job Progress'."
SYNTAX INTEGER {
other(1),
unknown(2),
uncollatedSheets(3), -- sheets within each document copy
-- are not collated: 1 1 ..., 2 2 ...,
-- No corresponding value of IPP
-- "multiple-document-handling"
collatedDocuments(4), -- internal collated sheets,
-- documents: A, B, A, B, ...
-- Corresponds to IPP "multiple-
-- document-handling"='separate-
-- documents-collated-copies'
uncollatedDocuments(5) -- internal collated sheets,
-- documents: A, A, ..., B, B, ...
-- Corresponds to IPP "multiple-
-- document-handling"='separate-
-- documents-uncollated-copies'
Bergman, et al. Informational [Page 74]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
}
JmJobSubmissionIDTypeTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies the format type of a job submission ID.
Each job submission ID is a fixed-length, 48-octet printable
US-ASCII [US-ASCII] coded character string containing no
control characters, consisting of the fields defined in section
3.5.1.
This is like a type 2 enumeration. See section 3.7.3."
SYNTAX OCTET STRING(SIZE(1)) -- ASCII '0'-'9', 'A'-'Z', 'a'-'z'
JmJobStateTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The current state of the job (pending, processing, completed,
etc.). The following figure shows the normal job state
transitions:
+----> canceled(7)
/
+---> pending(3) -------> processing(5) ------+------> completed(9)
| ^ ^ \
--->+ | | +----> aborted(8)
| v v /
+---> pendingHeld(4) processingStopped(6) ---+
Figure 4 - Normal Job State Transitions
Normally a job progresses from left to right. Other state
transitions are unlikely, but are not forbidden. Not shown are
the transitions to the canceled state from the pending,
pendingHeld, and processingStopped states.
Jobs in the pending, processing, and processingStopped states
are called 'active', while jobs in the pendingHeld, canceled,
aborted, and completed states are called 'inactive'. Jobs
reach one of the three terminal states: completed, canceled, or
aborted, after the jobs have completed all activity, and all
MIB objects and attributes have reached their final values for
the job.
Bergman, et al. Informational [Page 75]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
These values are the same as the enum values of the IPP 'job-
state' job attribute. See Section 3.7.1.2.
unknown(2),
The job state is not known, or its state is indeterminate.
pending(3),
The job is a candidate to start processing, but is not yet
processing.
pendingHeld(4),
The job is not a candidate for processing for any number of
reasons but will return to the pending state as soon as the
reasons are no longer present. The job's
jmJobStateReasons1 object and/or jobStateReasonsN (N=2..4)
attributes SHALL indicate why the job is no longer a
candidate for processing. The reasons are represented as
bits in the jmJobStateReasons1 object and/or
jobStateReasonsN (N=2..4) attributes. See the
JmJobStateReasonsNTC (N=1..4) textual convention for the
specification of each reason.
processing(5),
One or more of:
1. the job is using, or is attempting to use, one or
more purely software processes that are analyzing,
creating, or interpreting a PDL, etc.,
2. the job is using, or is attempting to use, one or
more hardware devices that are interpreting a PDL,
making mark on a medium, and/or performing finishing,
such as stapling, etc., OR
3. (configuration 2) the server has made the job ready
for printing, but the output device is not yet printing
it, either because the job hasn't reached the output
device or because the job is queued in the output
device or some other spooler, awaiting the output
device to print it.
When the job is in the processing state, the entire job
state includes the detailed status represented in the
device MIB indicated by the hrDeviceIndex value of the
job's physicalDevice attribute, if the agent implements
such a device MIB.
Implementations MAY, though they NEED NOT, include
Bergman, et al. Informational [Page 76]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
additional values in the job's jmJobStateReasons1 object
to indicate the progress of the job, such as adding the
jobPrinting value to indicate when the device is actually
making marks on a medium and/or the processingToStopPoint
value to indicate that the server or device is in the
process of canceling or aborting the job.
processingStopped(6),
The job has stopped while processing for any number of
reasons and will return to the processing state as soon
as the reasons are no longer present.
The job's jmJobStateReasons1 object and/or the job's
jobStateReasonsN (N=2..4) attributes MAY indicate why the
job has stopped processing. For example, if the output
device is stopped, the deviceStopped value MAY be
included in the job's jmJobStateReasons1 object.
NOTE - When an output device is stopped, the device
usually indicates its condition in human readable form
at the device. The management application can obtain
more complete device status remotely by querying the
appropriate device MIB using the job's deviceIndex
attribute(s), if the agent implements such a device MIB
canceled(7),
A client has canceled the job and the server or device
has completed canceling the job AND all MIB objects and
attributes have reached their final values for the job.
While the server or device is canceling the job, the
job's jmJobStateReasons1 object SHOULD contain the
processingToStopPoint value and one of the
canceledByUser, canceledByOperator, or canceledAtDevice
values. The canceledByUser, canceledByOperator, or
canceledAtDevice values remain while the job is in the
canceled state.
aborted(8),
The job has been aborted by the system, usually while the
job was in the processing or processingStopped state and
the server or device has completed aborting the job AND
all MIB objects and attributes have reached their final
values for the job. While the server or device is
aborting the job, the job's jmJobStateReasons1 object MAY
contain the processingToStopPoint and abortedBySystem
values. If implemented, the abortedBySystem value SHALL
remain while the job is in the aborted state.
Bergman, et al. Informational [Page 77]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
completed(9)
The job has completed successfully or with warnings or
errors after processing and all of the media have been
successfully stacked in the appropriate output bin(s) AND
all MIB objects and attributes have reached their final
values for the job. The job's jmJobStateReasons1 object
SHOULD contain one of: completedSuccessfully,
completedWithWarnings, or completedWithErrors values.
This is a type 2 enumeration. See Section 3.7.1.2."
SYNTAX INTEGER {
unknown(2),
pending(3),
pendingHeld(4),
processing(5),
processingStopped(6),
canceled(7),
aborted(8),
completed(9)
}
JmAttributeTypeTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The type of the attribute which identifies the attribute.
NOTE - The enum assignments are grouped logically with values
assigned in groups of 20, so that additional values may be
registered in the future and assigned a value that is part of
their logical grouping.
Values in the range 2**30 to 2**31-1 are reserved for private
or experimental usage. This range corresponds to the same
range reserved in IPP. Implementers are warned that use of
such values may conflict with other implementations.
Implementers are encouraged to request registration of enum
values following the procedures in Section 3.7.1.
See Section 3.2 entitled 'The Attribute Mechanism' for a
description of this textual-convention and its use in the
jmAttributeTable. See Section 3.3.8 for the specification of
each attribute. The comment(s) after each enum assignment
specifies the data type(s) of the attribute.
This is a type 2 enumeration. See Section 3.7.1.2."
Bergman, et al. Informational [Page 78]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
SYNTAX INTEGER {
other(1), -- Integer32 (-2..2147483647)
-- AND/OR
-- OCTET STRING(SIZE(0..63))
-- Job State attributes:
jobStateReasons2(3), -- JmJobStateReasons2TC
jobStateReasons3(4), -- JmJobStateReasons3TC
jobStateReasons4(5), -- JmJobStateReasons4TC
processingMessage(6), -- JmUTF8StringTC (SIZE(0..63))
processingMessageNaturalLangTag(7),
-- OCTET STRING(SIZE(0..63))
jobCodedCharSet(8), -- CodedCharSet
jobNaturalLanguageTag(9), -- OCTET STRING(SIZE(0..63))
-- Job Identification attributes:
jobURI(20), -- OCTET STRING(SIZE(0..63))
jobAccountName(21), -- OCTET STRING(SIZE(0..63))
serverAssignedJobName(22), -- JmJobStringTC (SIZE(0..63))
jobName(23), -- JmJobStringTC (SIZE(0..63))
jobServiceTypes(24), -- JmJobServiceTypesTC
jobSourceChannelIndex(25), -- Integer32 (0..2147483647)
jobSourcePlatformType(26), -- JmJobSourcePlatformTypeTC
submittingServerName(27), -- JmJobStringTC (SIZE(0..63))
submittingApplicationName(28), -- JmJobStringTC (SIZE(0..63))
jobOriginatingHost(29), -- JmJobStringTC (SIZE(0..63))
deviceNameRequested(30), -- JmJobStringTC (SIZE(0..63))
queueNameRequested(31), -- JmJobStringTC (SIZE(0..63))
physicalDevice(32), -- hrDeviceIndex
-- AND/OR
-- JmUTF8StringTC (SIZE(0..63))
numberOfDocuments(33), -- Integer32 (-2..2147483647)
fileName(34), -- JmJobStringTC (SIZE(0..63))
documentName(35), -- JmJobStringTC (SIZE(0..63))
jobComment(36), -- JmJobStringTC (SIZE(0..63))
documentFormatIndex(37), -- Integer32 (0..2147483647)
documentFormat(38), -- PrtInterpreterLangFamilyTC
-- AND/OR
-- OCTET STRING(SIZE(0..63))
-- Job Parameter attributes:
jobPriority(50), -- Integer32 (-2..100)
jobProcessAfterDateAndTime(51), -- DateAndTime (SNMPv2-TC)
jobHold(52), -- JmBooleanTC
jobHoldUntil(53), -- JmJobStringTC (SIZE(0..63))
outputBin(54), -- Integer32 (0..2147483647)
-- AND/OR
Bergman, et al. Informational [Page 79]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
-- JmJobStringTC (SIZE(0..63))
sides(55), -- Integer32 (-2..2)
finishing(56), -- JmFinishingTC
-- Image Quality attributes:
printQualityRequested(70), -- JmPrintQualityTC
printQualityUsed(71), -- JmPrintQualityTC
printerResolutionRequested(72), -- JmPrinterResolutionTC
printerResolutionUsed(73), -- JmPrinterResolutionTC
tonerEcomonyRequested(74), -- JmTonerEconomyTC
tonerEcomonyUsed(75), -- JmTonerEconomyTC
tonerDensityRequested(76), -- Integer32 (-2..100)
tonerDensityUsed(77), -- Integer32 (-2..100)
-- Job Progress attributes:
jobCopiesRequested(90), -- Integer32 (-2..2147483647)
jobCopiesCompleted(91), -- Integer32 (-2..2147483647)
documentCopiesRequested(92), -- Integer32 (-2..2147483647)
documentCopiesCompleted(93), -- Integer32 (-2..2147483647)
jobKOctetsTransferred(94), -- Integer32 (-2..2147483647)
sheetCompletedCopyNumber(95), -- Integer32 (-2..2147483647)
sheetCompletedDocumentNumber(96),
-- Integer32 (-2..2147483647)
jobCollationType(97), -- JmJobCollationTypeTC
-- Impression attributes:
impressionsSpooled(110), -- Integer32 (-2..2147483647)
impressionsSentToDevice(111), -- Integer32 (-2..2147483647)
impressionsInterpreted(112), -- Integer32 (-2..2147483647)
impressionsCompletedCurrentCopy(113),
-- Integer32 (-2..2147483647)
fullColorImpressionsCompleted(114),
-- Integer32 (-2..2147483647)
highlightColorImpressionsCompleted(115),
-- Integer32 (-2..2147483647)
-- Page attributes:
pagesRequested(130), -- Integer32 (-2..2147483647)
pagesCompleted(131), -- Integer32 (-2..2147483647)
pagesCompletedCurrentCopy(132), -- Integer32 (-2..2147483647)
-- Sheet attributes:
sheetsRequested(150), -- Integer32 (-2..2147483647)
sheetsCompleted(151), -- Integer32 (-2..2147483647)
sheetsCompletedCurrentCopy(152),-- Integer32 (-2..2147483647)
-- Resource attributes:
Bergman, et al. Informational [Page 80]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
mediumRequested(170), -- JmMediumTypeTC
-- AND/OR
-- JmJobStringTC (SIZE(0..63))
mediumConsumed(171), -- Integer32 (-2..2147483647)
-- AND
-- JmJobStringTC (SIZE(0..63))
colorantRequested(172), -- Integer32 (-2..2147483647)
-- AND/OR
-- JmJobStringTC (SIZE(0..63))
colorantConsumed(173), -- Integer32 (-2..2147483647)
-- AND/OR
-- JmJobStringTC (SIZE(0..63))
mediumTypeConsumed(174), -- Integer32 (-2..2147483647)
-- AND
-- JmJobStringTC (SIZE(0..63))
mediumSizeConsumed(175), -- Integer32 (-2..2147483647)
-- AND
-- JmJobStringTC (SIZE(0..63))
-- Time attributes:
jobSubmissionToServerTime(190), -- JmTimeStampTC
-- AND/OR
-- DateAndTime
jobSubmissionTime(191), -- JmTimeStampTC
-- AND/OR
-- DateAndTime
jobStartedBeingHeldTime(192), -- JmTimeStampTC
-- AND/OR
-- DateAndTime
jobStartedProcessingTime(193), -- JmTimeStampTC
-- AND/OR
-- DateAndTime
jobCompletionTime(194), -- JmTimeStampTC
-- AND/OR
-- DateAndTime
jobProcessingCPUTime(195) -- Integer32 (-2..2147483647)
}
JmJobServiceTypesTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Specifies the type(s) of service to which the job has been
submitted (print, fax, scan, etc.). The service type is
represented as an enum that is bit encoded with each job
service type so that more general and arbitrary services can be
created, such as services with more than one destination type,
Bergman, et al. Informational [Page 81]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
or ones with only a source or only a destination. For example,
a job service might scan, faxOut, and print a single job. In
this case, three bits would be set in the jobServiceTypes
attribute, corresponding to the hexadecimal values: 0x8 + 0x20
+ 0x4, respectively, yielding: 0x2C.
Whether this attribute is set from a job attribute supplied by
the job submission client or is set by the recipient job
submission server or device depends on the job submission
protocol. With either implementation, the agent SHALL return a
non-zero value for this attribute indicating the type of the
job.
One of the purposes of this attribute is to permit a requester
to filter out jobs that are not of interest. For example, a
printer operator MAY only be interested in jobs that include
printing. That is why the attribute is in the job
identification category.
The following service component types are defined (in
hexadecimal) and are assigned a separate bit value for use with
the jobServiceTypes attribute:
other 0x1
The job contains some instructions that are not one of the
identified types.
unknown 0x2
The job contains some instructions whose type is unknown to
the agent.
print 0x4
The job contains some instructions that specify printing
scan 0x8
The job contains some instructions that specify scanning
faxIn 0x10
The job contains some instructions that specify receive fax
faxOut 0x20
The job contains some instructions that specify sending fax
getFile 0x40
The job contains some instructions that specify accessing
files or documents
putFile 0x80
Bergman, et al. Informational [Page 82]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
The job contains some instructions that specify storing
files or documents
mailList 0x100
The job contains some instructions that specify
distribution of documents using an electronic mail system.
These bit definitions are the equivalent of a type 2 enum
except that combinations of them MAY be used together. See
section 3.7.1.2."
SYNTAX INTEGER (0..2147483647) -- 31 bits, all but sign bit
JmJobStateReasons1TC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The JmJobStateReasonsNTC (N=1..4) textual-conventions are used
with the jmJobStateReasons1 object and jobStateReasonsN
(N=2..4), respectively, to provide additional information
regarding the current jmJobState object value. These values
MAY be used with any job state or states for which the reason
makes sense. See section 3.3.9.1 for the specification of each
bit value defined for use with the JmJobStateReasons1TC.
These bit definitions are the equivalent of a type 2 enum
except that combinations of bits may be used together. See
section 3.7.1.2."
SYNTAX INTEGER (0..2147483647) -- 31 bits, all but sign bit
JmJobStateReasons2TC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual-convention is used with the jobStateReasons2
attribute to provides additional information regarding the
jmJobState object. See section 3.3.9.2 for the specification
of JmJobStateReasons2TC. See section 3.3.9.1 for the
description under JmJobStateReasons1TC for additional
information that applies to all reasons.
These bit definitions are the equivalent of a type 2 enum
except that combinations of them may be used together. See
section 3.7.1.2."
SYNTAX INTEGER (0..2147483647) -- 31 bits, all but sign bit
JmJobStateReasons3TC ::= TEXTUAL-CONVENTION
Bergman, et al. Informational [Page 83]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
STATUS current
DESCRIPTION
"This textual-convention is used with the jobStateReasons3
attribute to provides additional information regarding the
jmJobState object. See section 3.3.9.3 for the specification
of JmJobStateReasons3TC. See section 3.3.9.1 for the
description under JmJobStateReasons1TC for additional
information that applies to all reasons.
These bit definitions are the equivalent of a type 2 enum
except that combinations of them may be used together. See
section 3.7.1.2. "
SYNTAX INTEGER (0..2147483647) -- 31 bits, all but sign bit
JmJobStateReasons4TC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This textual-convention is used in the jobStateReasons4
attribute to provides additional information regarding the
jmJobState object. See section 3.3.9.4 for the specification
of JmJobStateReasons4TC. See section 3.3.9.1 for the
description under JmJobStateReasons1TC for additional
information that applies to all reasons.
These bit definitions are the equivalent of a type 2 enum
except that combinations of them may be used together. See
section 3.7.1.2."
SYNTAX INTEGER (0..2147483647) -- 31 bits, all but sign bit
jobmonMIBObjects OBJECT IDENTIFIER ::= { jobmonMIB 1 }
-- The General Group (MANDATORY)
-- The jmGeneralGroup consists entirely of the jmGeneralTable.
jmGeneral OBJECT IDENTIFIER ::= { jobmonMIBObjects 1 }
jmGeneralTable OBJECT-TYPE
SYNTAX SEQUENCE OF JmGeneralEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Bergman, et al. Informational [Page 84]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
"The jmGeneralTable consists of information of a general nature
that are per-job-set, but are not per-job. See Section 2
entitled 'Terminology and Job Model' for the definition of a
job set.
The MANDATORY-GROUP macro specifies that this group is
MANDATORY."
::= { jmGeneral 1 }
jmGeneralEntry OBJECT-TYPE
SYNTAX JmGeneralEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a job set (queue).
An entry SHALL exist in this table for each job set."
INDEX { jmGeneralJobSetIndex }
::= { jmGeneralTable 1 }
JmGeneralEntry ::= SEQUENCE {
jmGeneralJobSetIndex Integer32 (1..32767),
jmGeneralNumberOfActiveJobs Integer32 (0..2147483647),
jmGeneralOldestActiveJobIndex Integer32 (0..2147483647),
jmGeneralNewestActiveJobIndex Integer32 (0..2147483647),
jmGeneralJobPersistence Integer32 (15..2147483647),
jmGeneralAttributePersistence Integer32 (15..2147483647),
jmGeneralJobSetName JmUTF8StringTC (SIZE(0..63))
}
jmGeneralJobSetIndex OBJECT-TYPE
SYNTAX Integer32 (1..32767)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique value for each job set in this MIB. The jmJobTable
and jmAttributeTable tables have this same index as their
primary index.
The value(s) of the jmGeneralJobSetIndex SHALL be persistent
across power cycles, so that clients that have retained
jmGeneralJobSetIndex values will access the same job sets upon
subsequent power-up.
An implementation that has only one job set, such as a printer
Bergman, et al. Informational [Page 85]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
with a single queue, SHALL hard code this object with the value
1.
See Section 2 entitled 'Terminology and Job Model' for the
definition of a job set.
Corresponds to the first index in jmJobTable and
jmAttributeTable."
::= { jmGeneralEntry 1 }
jmGeneralNumberOfActiveJobs OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current number of 'active' jobs in the jmJobIDTable,
jmJobTable, and jmAttributeTable, i.e., the total number of
jobs that are in the pending, processing, or processingStopped
states. See the JmJobStateTC textual-convention for the exact
specification of the semantics of the job states."
DEFVAL { 0 } -- no jobs
::= { jmGeneralEntry 2 }
jmGeneralOldestActiveJobIndex OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The jmJobIndex of the oldest job that is still in one of the
'active' states (pending, processing, or processingStopped).
In other words, the index of the 'active' job that has been in
the job tables the longest.
If there are no active jobs, the agent SHALL set the value of
this object to 0.
See Section 3.2 entitled 'The Job Tables and the Oldest Active
and Newest Active Indexes' for a description of the usage of
this object."
DEFVAL { 0 } -- no active jobs
::= { jmGeneralEntry 3 }
jmGeneralNewestActiveJobIndex OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
Bergman, et al. Informational [Page 86]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
STATUS current
DESCRIPTION
"The jmJobIndex of the newest job that is in one of the
'active' states (pending, processing, or processingStopped).
In other words, the index of the 'active' job that has been
most recently added to the job tables.
When all jobs become 'inactive', i.e., enter the pendingHeld,
completed, canceled, or aborted states, the agent SHALL set the
value of this object to 0.
See Section 3.2 entitled 'The Job Tables and the Oldest Active
and Newest Active Indexes' for a description of the usage of
this object."
DEFVAL { 0 } -- no active jobs
::= { jmGeneralEntry 4 }
jmGeneralJobPersistence OBJECT-TYPE
SYNTAX Integer32 (15..2147483647)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum time in seconds for this instance of the Job Set
that an entry SHALL remain in the jmJobIDTable and jmJobTable
after processing has completed, i.e., the minimum time in
seconds starting when the job enters the completed, canceled,
or aborted state.
Configuring this object is implementation-dependent.
This value SHALL be equal to or greater than the value of
jmGeneralAttributePersistence. This value SHOULD be at least
60 which gives a monitoring or accounting application one
minute in which to poll for job data."
DEFVAL { 60 } -- one minute
::= { jmGeneralEntry 5 }
jmGeneralAttributePersistence OBJECT-TYPE
SYNTAX Integer32 (15..2147483647)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Bergman, et al. Informational [Page 87]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
"The minimum time in seconds for this instance of the Job Set
that an entry SHALL remain in the jmAttributeTable after
processing has completed , i.e., the time in seconds starting
when the job enters the completed, canceled, or aborted state.
Configuring this object is implementation-dependent.
This value SHOULD be at least 60 which gives a monitoring or
accounting application one minute in which to poll for job
data."
DEFVAL { 60 } -- one minute
::= { jmGeneralEntry 6 }
jmGeneralJobSetName OBJECT-TYPE
SYNTAX JmUTF8StringTC (SIZE(0..63))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The human readable name of this job set assigned by the system
administrator (by means outside of this MIB). Typically, this
name SHOULD be the name of the job queue. If a server or
device has only a single job set, this object can be the
administratively assigned name of the server or device itself.
This name does not need to be unique, though each job set in a
single Job Monitoring MIB SHOULD have distinct names.
NOTE - If the job set corresponds to a single printer and the
Printer MIB is implemented, this value SHOULD be the same as
the prtGeneralPrinterName object in the draft Printer MIB
[print-mib-draft]. If the job set corresponds to an IPP
Printer, this value SHOULD be the same as the IPP 'printer-
name' Printer attribute.
NOTE - The purpose of this object is to help the user of the
job monitoring application distinguish between several job sets
in implementations that support more than one job set.
See the OBJECT compliance macro for the minimum maximum length
required for conformance."
DEFVAL { ''H } -- empty string
::= { jmGeneralEntry 7 }
-- The Job ID Group (MANDATORY)
-- The jmJobIDGroup consists entirely of the jmJobIDTable.
Bergman, et al. Informational [Page 88]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
jmJobID OBJECT IDENTIFIER ::= { jobmonMIBObjects 2 }
jmJobIDTable OBJECT-TYPE
SYNTAX SEQUENCE OF JmJobIDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The jmJobIDTable provides a correspondence map (1) between the
job submission ID that a client uses to refer to a job and (2)
the jmGeneralJobSetIndex and jmJobIndex that the Job Monitoring
MIB agent assigned to the job and that are used to access the
job in all of the other tables in the MIB. If a monitoring
application already knows the jmGeneralJobSetIndex and the
jmJobIndex of the job it is querying, that application NEED NOT
use the jmJobIDTable.
The MANDATORY-GROUP macro specifies that this group is
MANDATORY."
::= { jmJobID 1 }
jmJobIDEntry OBJECT-TYPE
SYNTAX JmJobIDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The map from (1) the jmJobSubmissionID to (2) the
jmGeneralJobSetIndex and jmJobIndex.
An entry SHALL exist in this table for each job currently known
to the agent for all job sets and job states. There MAY be
more than one jmJobIDEntry that maps to a single job. This
many to one mapping can occur when more than one network entity
along the job submission path supplies a job submission ID.
See Section 3.5. However, each job SHALL appear once and in
one and only one job set."
INDEX { jmJobSubmissionID }
::= { jmJobIDTable 1 }
JmJobIDEntry ::= SEQUENCE {
jmJobSubmissionID OCTET STRING(SIZE(48)),
jmJobIDJobSetIndex Integer32 (0..32767),
jmJobIDJobIndex Integer32 (0..2147483647)
}
jmJobSubmissionID OBJECT-TYPE
Bergman, et al. Informational [Page 89]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
SYNTAX OCTET STRING(SIZE(48))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A quasi-unique 48-octet fixed-length string ID which
identifies the job within a particular client-server
environment. There are multiple formats for the
jmJobSubmissionID. Each format SHALL be uniquely identified.
See the JmJobSubmissionIDTypeTC textual convention. Each
format SHALL be registered using the procedures of a type 2
enum. See section 3.7.3 entitled: 'PWG Registration of Job
Submission Id Formats'.
If the requester (client or server) does not supply a job
submission ID in the job submission protocol, then the
recipient (server or device) SHALL assign a job submission ID
using any of the standard formats that have been reserved for
agents and adding the final 8 octets to distinguish the ID from
others submitted from the same requester.
The monitoring application, whether in the client or running
separately, MAY use the job submission ID to help identify
which jmJobIndex was assigned by the agent, i.e., in which row
the job information is in the other tables.
NOTE - fixed-length is used so that a management application
can use a shortened GetNext varbind (in SNMPv1 and SNMPv2) in
order to get the next submission ID, disregarding the remainder
of the ID in order to access jobs independent of the trailing
identifier part, e.g., to get all jobs submitted by a
particular jmJobOwner or submitted from a particular MAC
address.
See the JmJobSubmissionIDTypeTC textual convention.
See APPENDIX B - Support of Job Submission Protocols."
::= { jmJobIDEntry 1 }
jmJobIDJobSetIndex OBJECT-TYPE
SYNTAX Integer32 (0..32767)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the value of the jmGeneralJobSetIndex for
the job with the jmJobSubmissionID value, i.e., the job set
index of the job set in which the job was placed when that
server or device accepted the job. This 16-bit value in
Bergman, et al. Informational [Page 90]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
combination with the jmJobIDJobIndex value permits the
management application to access the other tables to obtain the
job-specific objects for this job.
See jmGeneralJobSetIndex in the jmGeneralTable."
DEFVAL { 0 } -- 0 indicates no job set index
::= { jmJobIDEntry 2 }
jmJobIDJobIndex OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the value of the jmJobIndex for the job
with the jmJobSubmissionID value, i.e., the job index for the
job when the server or device accepted the job. This value, in
combination with the jmJobIDJobSetIndex value, permits the
management application to access the other tables to obtain the
job-specific objects for this job.
See jmJobIndex in the jmJobTable."
DEFVAL { 0 } -- 0 indicates no jmJobIndex value.
::= { jmJobIDEntry 3 }
-- The Job Group (MANDATORY)
-- The jmJobGroup consists entirely of the jmJobTable.
jmJob OBJECT IDENTIFIER ::= { jobmonMIBObjects 3 }
jmJobTable OBJECT-TYPE
SYNTAX SEQUENCE OF JmJobEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The jmJobTable consists of basic job state and status
information for each job in a job set that (1) monitoring
applications need to be able to access in a single SNMP Get
operation, (2) that have a single value per job, and (3) that
SHALL always be implemented.
The MANDATORY-GROUP macro specifies that this group is
MANDATORY."
::= { jmJob 1 }
Bergman, et al. Informational [Page 91]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
jmJobEntry OBJECT-TYPE
SYNTAX JmJobEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Basic per-job state and status information.
An entry SHALL exist in this table for each job, no matter what
the state of the job is. Each job SHALL appear in one and only
one job set.
See Section 3.2 entitled 'The Job Tables'."
INDEX { jmGeneralJobSetIndex, jmJobIndex }
::= { jmJobTable 1 }
JmJobEntry ::= SEQUENCE {
jmJobIndex Integer32 (1..2147483647),
jmJobState JmJobStateTC,
jmJobStateReasons1 JmJobStateReasons1TC,
jmNumberOfInterveningJobs Integer32 (-2..2147483647),
jmJobKOctetsPerCopyRequested Integer32 (-2..2147483647),
jmJobKOctetsProcessed Integer32 (-2..2147483647),
jmJobImpressionsPerCopyRequested Integer32 (-2..2147483647),
jmJobImpressionsCompleted Integer32 (-2..2147483647),
jmJobOwner JmJobStringTC (SIZE(0..63))
}
jmJobIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The sequential, monatonically increasing identifier index for
the job generated by the server or device when that server or
device accepted the job. This index value permits the
management application to access the other tables to obtain the
job-specific row entries.
See Section 3.2 entitled 'The Job Tables and the Oldest Active
and Newest Active Indexes'.
See Section 3.5 entitled 'Job Identification'.
See also jmGeneralNewestActiveJobIndex for the largest value of
jmJobIndex.
See JmJobSubmissionIDTypeTC for a limit on the size of this
index if the agent represents it as an 8-digit decimal number."
::= { jmJobEntry 1 }
Bergman, et al. Informational [Page 92]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
jmJobState OBJECT-TYPE
SYNTAX JmJobStateTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current state of the job (pending, processing, completed,
etc.). Agents SHALL implement only those states which are
appropriate for the particular implementation. However,
management applications SHALL be prepared to receive all the
standard job states.
The final value for this object SHALL be one of: completed,
canceled, or aborted. The minimum length of time that the
agent SHALL maintain MIB data for a job in the completed,
canceled, or aborted state before removing the job data from
the jmJobIDTable and jmJobTable is specified by the value of
the jmGeneralJobPersistence object."
DEFVAL { unknown } -- default is unknown
::= { jmJobEntry 2 }
jmJobStateReasons1 OBJECT-TYPE
SYNTAX JmJobStateReasons1TC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Additional information about the job's current state, i.e.,
information that augments the value of the job's jmJobState
object.
Implementation of any reason values is OPTIONAL, but an agent
SHOULD return any reason information available. These values
MAY be used with any job state or states for which the reason
makes sense. Since the Job State Reasons will be more dynamic
than the Job State, it is recommended that a job monitoring
application read this object every time jmJobState is read.
When the agent cannot provide a reason for the current state of
the job, the value of the jmJobStateReasons1 object and
jobStateReasonsN attributes SHALL be 0.
The jobStateReasonsN (N=2..4) attributes provide further
additional information about the job's current state."
DEFVAL { 0 } -- no reasons
::= { jmJobEntry 3 }
Bergman, et al. Informational [Page 93]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
jmNumberOfInterveningJobs OBJECT-TYPE
SYNTAX Integer32 (-2..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of jobs that are expected to complete processing
before this job has completed processing according to the
implementation's queuing algorithm, if no other jobs were to be
submitted. In other words, this value is the job's queue
position. The agent SHALL return a value of 0 for this
attribute when the job is the next job to complete processing
(or has completed processing)."
DEFVAL { 0 } -- default is no intervening jobs.
::= { jmJobEntry 4 }
jmJobKOctetsPerCopyRequested OBJECT-TYPE
SYNTAX Integer32 (-2..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total size in K (1024) octets of the document(s) being
requested to be processed in the job. The agent SHALL round
the actual number of octets up to the next highest K. Thus 0
octets is represented as '0', 1-1024 octets is represented as
'1', 1025-2048 is represented as '2', etc.
In computing this value, the server/device SHALL NOT include
the multiplicative factors contributed by (1) the number of
document copies, and (2) the number of job copies, independent
of whether the device can process multiple copies of the job or
document without making multiple passes over the job or
document data and independent of whether the output is collated
or not. Thus the server/device computation is independent of
the implementation and indicates the size of the document(s)
measured in K octets independent of the number of copies."
DEFVAL { -2 } -- the default is unknown(-2)
::= { jmJobEntry 5 }
jmJobKOctetsProcessed OBJECT-TYPE
SYNTAX Integer32 (-2..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets processed by the server or device
Bergman, et al. Informational [Page 94]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
measured in units of K (1024) octets so far. The agent SHALL
round the actual number of octets processed up to the next
higher K. Thus 0 octets is represented as '0', 1-1024 octets
is represented as '1', 1025-2048 octets is '2', etc. For
printing devices, this value is the number interpreted by the
page description language interpreter rather than what has been
marked on media.
For implementations where multiple copies are produced by the
interpreter with only a single pass over the data, the final
value SHALL be equal to the value of the
jmJobKOctetsPerCopyRequested object. For implementations where
multiple copies are produced by the interpreter by processing
the data for each copy, the final value SHALL be a multiple of
the value of the jmJobKOctetsPerCopyRequested object.
NOTE - See the impressionsCompletedCurrentCopy and
pagesCompletedCurrentCopy attributes for attributes that are
reset on each document copy.
NOTE - The jmJobKOctetsProcessed object can be used with the
jmJobKOctetsPerCopyRequested object to provide an indication of
the relative progress of the job, provided that the
multiplicative factor is taken into account for some
implementations of multiple copies."
DEFVAL { 0 } -- default is no octets processed.
::= { jmJobEntry 6 }
jmJobImpressionsPerCopyRequested OBJECT-TYPE
SYNTAX Integer32 (-2..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total size in number of impressions of the document(s)
submitted.
In computing this value, the server/device SHALL NOT include
the multiplicative factors contributed by (1) the number of
document copies, and (2) the number of job copies, independent
of whether the device can process multiple copies of the job or
document without making multiple passes over the job or
document data and independent of whether the output is collated
or not. Thus the server/device computation is independent of
the implementation and reflects the size of the document(s)
measured in impressions independent of the number of copies.
See the definition of the term 'impression' in Section 2."
Bergman, et al. Informational [Page 95]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
DEFVAL { -2 } -- default is unknown(-2)
::= { jmJobEntry 7 }
jmJobImpressionsCompleted OBJECT-TYPE
SYNTAX Integer32 (-2..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of impressions completed for this job so far.
For printing devices, the impressions completed includes
interpreting, marking, and stacking the output. For other
types of job services, the number of impressions completed
includes the number of impressions processed.
NOTE - See the impressionsCompletedCurrentCopy and
pagesCompletedCurrentCopy attributes for attributes that are
reset on each document copy.
NOTE - The jmJobImpressionsCompleted object can be used with
the jmJobImpressionsPerCopyRequested object to provide an
indication of the relative progress of the job, provided that
the multiplicative factor is taken into account for some
implementations of multiple copies.
See the definition of the term 'impression' in Section 2 and
the counting example in Section 3.4 entitled 'Monitoring Job
Progress'."
DEFVAL { 0 } -- default is no octets
::= { jmJobEntry 8 }
jmJobOwner OBJECT-TYPE
SYNTAX JmJobStringTC (SIZE(0..63))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The coded character set name of the user that submitted the
job. The method of assigning this user name will be system
and/or site specific but the method MUST ensure that the name
is unique to the network that is visible to the client and
target device.
This value SHOULD be the most authenticated name of the user
submitting the job.
See the OBJECT compliance macro for the minimum maximum length
Bergman, et al. Informational [Page 96]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
required for conformance."
DEFVAL { ''H } -- default is empty string
::= { jmJobEntry 9 }
-- The Attribute Group (MANDATORY)
-- The jmAttributeGroup consists entirely of the jmAttributeTable.
--
-- Implementation of the objects in this group is MANDATORY.
-- See Section 3.1 entitled 'Conformance Considerations'.
-- An agent SHALL implement any attribute if (1) the server or device
-- supports the functionality represented by the attribute and (2) the
-- information is available to the agent.
jmAttribute OBJECT IDENTIFIER ::= { jobmonMIBObjects 4 }
jmAttributeTable OBJECT-TYPE
SYNTAX SEQUENCE OF JmAttributeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The jmAttributeTable SHALL contain attributes of the job and
document(s) for each job in a job set. Instead of allocating
distinct objects for each attribute, each attribute is
represented as a separate row in the jmAttributeTable.
The MANDATORY-GROUP macro specifies that this group is
MANDATORY. An agent SHALL implement any attribute if (1) the
server or device supports the functionality represented by the
attribute and (2) the information is available to the agent. "
::= { jmAttribute 1 }
jmAttributeEntry OBJECT-TYPE
SYNTAX JmAttributeEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Attributes representing information about the job and
document(s) or resources required and/or consumed.
Each entry in the jmAttributeTable is a per-job entry with an
extra index for each type of attribute (jmAttributeTypeIndex)
that a job can have and an additional index
(jmAttributeInstanceIndex) for those attributes that can have
Bergman, et al. Informational [Page 97]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
multiple instances per job. The jmAttributeTypeIndex object
SHALL contain an enum type that indicates the type of attribute
(see the JmAttributeTypeTC textual-convention). The value of
the attribute SHALL be represented in either the
jmAttributeValueAsInteger or jmAttributeValueAsOctets objects,
and/or both, as specified in the JmAttributeTypeTC textual-
convention.
The agent SHALL create rows in the jmAttributeTable as the
server or device is able to discover the attributes either from
the job submission protocol itself or from the document PDL.
As the documents are interpreted, the interpreter MAY discover
additional attributes and so the agent adds additional rows to
this table. As the attributes that represent resources are
actually consumed, the usage counter contained in the
jmAttributeValueAsInteger object is incremented according to
the units indicated in the description of the JmAttributeTypeTC
enum.
The agent SHALL maintain each row in the jmAttributeTable for
at least the minimum time after a job completes as specified by
the jmGeneralAttributePersistence object.
Zero or more entries SHALL exist in this table for each job in
a job set.
See Section 3.3 entitled 'The Attribute Mechanism' for a
description of the jmAttributeTable."
INDEX { jmGeneralJobSetIndex, jmJobIndex, jmAttributeTypeIndex,
jmAttributeInstanceIndex }
::= { jmAttributeTable 1 }
JmAttributeEntry ::= SEQUENCE {
jmAttributeTypeIndex JmAttributeTypeTC,
jmAttributeInstanceIndex Integer32 (1..32767),
jmAttributeValueAsInteger Integer32 (-2..2147483647),
jmAttributeValueAsOctets OCTET STRING(SIZE(0..63))
}
jmAttributeTypeIndex OBJECT-TYPE
SYNTAX JmAttributeTypeTC
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of attribute that this row entry represents.
The type MAY identify information about the job or document(s)
Bergman, et al. Informational [Page 98]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
or MAY identify a resource required to process the job before
the job start processing and/or consumed by the job as the job
is processed.
Examples of job attributes (i.e., apply to the job as a whole)
that have only one instance per job include:
jobCopiesRequested(90), documentCopiesRequested(92),
jobCopiesCompleted(91), documentCopiesCompleted(93), while
examples of job attributes that may have more than one instance
per job include: documentFormatIndex(37), and
documentFormat(38).
Examples of document attributes (one instance per document)
include: fileName(34), and documentName(35).
Examples of required and consumed resource attributes include:
pagesRequested(130), mediumRequested(170), pagesCompleted(131),
and mediumConsumed(171), respectively."
::= { jmAttributeEntry 1 }
jmAttributeInstanceIndex OBJECT-TYPE
SYNTAX Integer32 (1..32767)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A running 16-bit index of the attributes of the same type for
each job. For those attributes with only a single instance per
job, this index value SHALL be 1. For those attributes that
are a single value per document, the index value SHALL be the
document number, starting with 1 for the first document in the
job. Jobs with only a single document SHALL use the index
value of 1. For those attributes that can have multiple values
per job or per document, such as documentFormatIndex(37) or
documentFormat(38), the index SHALL be a running index for the
job as a whole, starting at 1."
::= { jmAttributeEntry 2 }
jmAttributeValueAsInteger OBJECT-TYPE
SYNTAX Integer32 (-2..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The integer value of the attribute. The value of the
attribute SHALL be represented as an integer if the enum
Bergman, et al. Informational [Page 99]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
description in the JmAttributeTypeTC textual-convention
definition has the tag: 'INTEGER:'.
Depending on the enum definition, this object value MAY be an
integer, a counter, an index, or an enum, depending on the
jmAttributeTypeIndex value. The units of this value are
specified in the enum description.
For those attributes that are accumulating job consumption as
the job is processed as specified in the JmAttributeTypeTC
textual-convention, SHALL contain the final value after the job
completes processing, i.e., this value SHALL indicate the total
usage of this resource made by the job.
A monitoring application is able to copy this value to a
suitable longer term storage for later processing as part of an
accounting system.
Since the agent MAY add attributes representing resources to
this table while the job is waiting to be processed or being
processed, which can be a long time before any of the resources
are actually used, the agent SHALL set the value of the
jmAttributeValueAsInteger object to 0 for resources that the
job has not yet consumed.
Attributes for which the concept of an integer value is
meaningless, such as fileName(34), jobName, and
processingMessage, do not have the 'INTEGER:' tag in the
JmAttributeTypeTC definition and so an agent SHALL always
return a value of '-1' to indicate 'other' for the value of the
jmAttributeValueAsInteger object for these attributes.
For attributes which do have the 'INTEGER:' tag in the
JmAttributeTypeTC definition, if the integer value is not (yet)
known, the agent either (1) SHALL not materialize the row in
the jmAttributeTable until the value is known or (2) SHALL
return a '-2' to represent an 'unknown' counting integer value,
a '0' to represent an 'unknown' index value, and a '2' to
represent an 'unknown(2)' enum value."
DEFVAL { -2 } -- default value is unknown(-2)
::= { jmAttributeEntry 3 }
jmAttributeValueAsOctets OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(0..63))
MAX-ACCESS read-only
STATUS current
Bergman, et al. Informational [Page 100]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
DESCRIPTION
"The octet string value of the attribute. The value of the
attribute SHALL be represented as an OCTET STRING if the enum
description in the JmAttributeTypeTC textual-convention
definition has the tag: 'OCTETS:'.
Depending on the enum definition, this object value MAY be a
coded character set string (text), such as 'JmUTF8StringTC', or
a binary octet string, such as 'DateAndTime'.
Attributes for which the concept of an octet string value is
meaningless, such as pagesCompleted, do not have the tag
'OCTETS:' in the JmAttributeTypeTC definition and so the agent
SHALL always return a zero length string for the value of the
jmAttributeValueAsOctets object.
For attributes which do have the 'OCTETS:' tag in the
JmAttributeTypeTC definition, if the OCTET STRING value is not
(yet) known, the agent either SHALL NOT materialize the row in
the jmAttributeTable until the value is known or SHALL return a
zero-length string."
DEFVAL { ''H } -- empty string
::= { jmAttributeEntry 4 }
-- Notifications and Trapping
-- Reserved for the future
jobmonMIBNotifications OBJECT IDENTIFIER ::= { jobmonMIB 2 }
-- Conformance Information
jmMIBConformance OBJECT IDENTIFIER ::= { jobmonMIB 3 }
-- compliance statements
jmMIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for agents that implement the
job monitoring MIB."
MODULE -- this module
MANDATORY-GROUPS {
jmGeneralGroup, jmJobIDGroup, jmJobGroup, jmAttributeGroup }
Bergman, et al. Informational [Page 101]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
OBJECT jmGeneralJobSetName
SYNTAX JmUTF8StringTC (SIZE(0..8))
DESCRIPTION
"Only 8 octets maximum string length NEED be supported by the
agent."
OBJECT jmJobOwner
SYNTAX JmJobStringTC (SIZE(0..16))
DESCRIPTION
"Only 16 octets maximum string length NEED be supported by the
agent."
-- There are no CONDITIONALLY MANDATORY or OPTIONAL groups.
::= { jmMIBConformance 1 }
jmMIBGroups OBJECT IDENTIFIER ::= { jmMIBConformance 2 }
jmGeneralGroup OBJECT-GROUP
OBJECTS {
jmGeneralNumberOfActiveJobs, jmGeneralOldestActiveJobIndex,
jmGeneralNewestActiveJobIndex, jmGeneralJobPersistence,
jmGeneralAttributePersistence, jmGeneralJobSetName}
STATUS current
DESCRIPTION
"The general group."
::= { jmMIBGroups 1 }
jmJobIDGroup OBJECT-GROUP
OBJECTS {
jmJobIDJobSetIndex, jmJobIDJobIndex }
STATUS current
DESCRIPTION
"The job ID group."
::= { jmMIBGroups 2 }
jmJobGroup OBJECT-GROUP
OBJECTS {
jmJobState, jmJobStateReasons1, jmNumberOfInterveningJobs,
jmJobKOctetsPerCopyRequested, jmJobKOctetsProcessed,
jmJobImpressionsPerCopyRequested, jmJobImpressionsCompleted,
jmJobOwner }
STATUS current
Bergman, et al. Informational [Page 102]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
DESCRIPTION
"The job group."
::= { jmMIBGroups 3 }
jmAttributeGroup OBJECT-GROUP
OBJECTS {
jmAttributeValueAsInteger, jmAttributeValueAsOctets }
STATUS current
DESCRIPTION
"The attribute group."
::= { jmMIBGroups 4 }
END
Bergman, et al. Informational [Page 103]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
5 Appendix A - Implementing the Job Life Cycle
The job object has well-defined states and client operations that
affect the transition between the job states. Internal server and
device actions also affect the transitions of the job between the job
states. These states and transitions are referred to as the job's
life cycle.
Not all implementations of job submission protocols have all of the
states of the job model specified here. The job model specified here
is intended to be a superset of most implementations. It is the
purpose of the agent to map the particular implementation's job life
cycle onto the one specified here. The agent MAY omit any states not
implemented. Only the processing and completed states are required
to be implemented by an agent. However, a conforming management
application SHALL be prepared to accept any of the states in the job
life cycle specified here, so that the management application can
interoperate with any conforming agent.
The job states are intended to be user visible. The agent SHALL make
these states visible in the MIB, but only for the subset of job
states that the implementation has. Some implementations MAY need to
have sub-states of these user-visible states. The jmJobStateReasons1
object and the jobStateReasonsN (N=2..4) attributes can be used to
represent the sub-states of the jobs.
Job states are intended to last a user-visible length of time in most
implementations. However, some jobs may pass through some states in
zero time in some situations and/or in some implementations.
The job model does not specify how accounting and auditing is
implemented, except to assume that accounting and auditing logs are
separate from the job life cycle and last longer than job entries in
the MIB. Jobs in the completed, aborted, or canceled states are not
logs, since jobs in these states are accessible via SNMP protocol
operations and SHALL be removed from the Job Monitoring MIB tables
after a site-settable or implementation-defined period of time. An
accounting application MAY copy accounting information incrementally
to an accounting log as a job processes, or MAY be copied while the
job is in the canceled, aborted, or completed states, depending on
implementation. The same is true for auditing logs.
The jmJobState object specifies the standard job states. The normal
job state transitions are shown in the state transition diagram
presented in Figure 4.
Bergman, et al. Informational [Page 104]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
6 APPENDIX B - Support of Job Submission Protocols
A companion PWG document, entitled "Job Submission Protocol Mapping
Recommendations for the Job Monitoring MIB" [protomap] contains the
recommended usage of each of the objects and attributes in this MIB
with a number of job submission protocols. In particular, which job
submission ID format should be used is indicated for each job
submission protocol.
Some job submission protocols have support for the client to specify
a job submission ID. A second approach is to enhance the document
format to embed the job submission ID in the document data. This
second approach is independent of the job submission protocol. This
appendix lists some examples of these approaches.
Some PJL implementations wrap a banner page as a PJL job around a job
submitted by a client. If this results in multiple job submission
IDs, the agent SHALL create multiple jmJobIDEntry rows in the
jmJobIDTable that each point to the same job entry in the job tables.
See the specification of the jmJobIDEntry.
7 References
[BCP-11] Bradner S. and R. Hovey, "The Organizations
Involved in the IETF Standards Process", BCP 11,
RFC 2028, October 1996.
[GB2312] GB 2312-1980, "Chinese People's Republic of China
(PRC) mixed one byte and two byte coded character
set"
[hr-mib] Grillo, P. and S. Waldbusser, "Host Resources
MIB", RFC 1514, September 1993.
[iana] Reynolds, J. and J. Postel, "Assigned Numbers",
STD 2, RFC 1700, October 1994.
[IANA-charsets] Coded Character Sets registered by IANA and
assigned an enum value for use in the CodedCharSet
textual convention imported from the Printer MIB.
See ftp://ftp.isi.edu/in-
notes/iana/assignments/character-sets
[iana-media-types] IANA Registration of MIME media types (MIME
content types/subtypes). See
ftp://ftp.isi.edu/in-notes/iana/assignments/
Bergman, et al. Informational [Page 105]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
[ipp-model] deBry, R., Hastings, T., Herriot, R., Issaacson,
S. and P. Powell, "The Internet Printing
Protocol/1.0: Model and Semantics", RFC 2566,
April 1999.
[ISO-639] ISO 639:1988 (E/F) - Code for Representation of
names of languages - The International
Organization for Standardization, 1st edition,
1988.
[ISO-646] ISO/IEC 646:1991, "Information technology -- ISO
7-bit coded character set for information
interchange", JTC1/SC2.
[ISO-2022] ISO/IEC 2022:1994 - "Information technology --
Character code structure and extension
techniques", JTC1/SC2.
[ISO-3166] ISO 3166:1988 (E/F) - Codes for representation of
names of countries - The International
Organization for Standardization, 3rd edition,
1988-08-15."
[ISO-8859-1] ISO/IEC 8859-1:1987, "Information technology --
8-bit single byte coded graphic character sets -
Part 1: Latin alphabet No. 1, JTC1/SC2."
[ISO-10646] ISO/IEC 10646-1:1993, "Information technology --
Universal Multiple-Octet Coded Character Set (UCS)
- Part 1: Architecture and Basic Multilingual
Plane, JTC1/SC2.
[iso-dpa] ISO/IEC 10175-1:1996 "Information technology --
Text and Office Systems -- Document Printing
Application (DPA) -- Part 1: Abstract service
definition and procedures. See
ftp://ftp.pwg.org/pub/pwg/dpa/
[JIS X0208] JIS X0208-1990, "Japanese two byte coded character
set."
[mib-II] McCloghrie, K. and M. Rose, "Management
Information Base for Network Management of
TCP/IP-based internets: MIB-II", STD 17, RFC 1213,
March 1991.
Bergman, et al. Informational [Page 106]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
[print-mib] Smith, R., Wright, F., Hastings, T., Zilles, S.
and J. Gyllenskog, "Printer MIB", RFC 1759, March
1995.
[print-mib-draft] Turner, R., "Printer MIB", Work in Progress,
[protomap] Bergman, R., "Job Submission Protocol Mapping
Recommendations for the Job Monitoring MIB", RFC
2708, November 1999.
[pwg] The Printer Working Group is a printer industry
consortium open to any individuals. For more
information, access the PWG web page:
http://www.pwg.org
[RFC1179] McLaughlin, L., III, "Line Printer Daemon
Protocol", RFC 1179, August 1990.
[RFC1738] Berners-Lee, T., Masinter, L. and M., McCahill,
"Uniform Resource Locators (URL)", RFC 1738,
December 1994.
[RFC1766] Avelstrand, H., "Tags for the Identification of
Languages", RFC 1766, March 1995.
[RFC2026] Bradner, S., "The Internet Standards Process --
Revision 3", BCP 9, RFC 2026, October 1996.
[RFC2119] Bradner, S., "Keywords for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2277] Alvestrand, H., "IETF Policy on Character Sets and
Languages", BCP 18, RFC 2277, January 1998.
[RFC2278] Freed, N. and J. Postel, "IANA CharSet
Registration Procedures", BCP 19, RFC 2278,
January 1998.
[SMIv2-SMI] McCloghrie, K., Perkins, D. and J. Schoenwaelder,
"Structure of Management Information Version 2
(SMIv2)", STD 58, RFC 2578, April 1999.
[SMIv2-TC] McCloghrie, K., Perkins, D. and J. Schoenwaelder,
"Textual Conventions for SMIv2", STD 58, RFC 2579,
April 1999.
Bergman, et al. Informational [Page 107]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
[tipsi] IEEE 1284.1, Transport-independent Printer System
Interface (TIPSI).
[URI-spec] Berners-Lee, T., Fielding, R. and L. Masinter,
"Uniform Resource Identifiers (URI), Generic
Syntax", RFC 2396, August 1998.
[US-ASCII] Coded Character Set - 7-bit American Standard Code
for Information Interchange, ANSI X3.4-1986.
[UTF-8] Yergeau, F., "UTF-8, a transformation format of
ISO 10646", RFC 2279, January 1998.
8 Notices
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11 [BCP-11].
Copies of claims of rights made available for publication and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
Bergman, et al. Informational [Page 108]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
9 Authors' Addresses
Ron Bergman
Dataproducts Corp.
1757 Tapo Canyon Road
Simi Valley, CA 93063-3394
Phone: 805-578-4421
Fax: 805-578-4001
EMail: rbergma@dpc.com
Tom Hastings
Xerox Corporation, ESAE-231
737 Hawaii St.
El Segundo, CA 90245
Phone: 310-333-6413
Fax: 310-333-5514
EMail: hastings@cp10.es.xerox.com
Scott A. Isaacson
Novell, Inc.
122 E 1700 S
Provo, UT 84606
Phone: 801-861-7366
Fax: 801-861-4025
EMail: scott_isaacson@novell.com
Harry Lewis
IBM Corporation
6300 Diagonal Hwy
Boulder, CO 80301
Phone: (303) 924-5337
EMail: harryl@us.ibm.com
Send questions and comments to the Printer Working Group (PWG)
using the Job Monitoring Project (JMP) Mailing List: jmp@pwg.org
To learn how to subscribe, send email to: jmp-request@pwg.org
Bergman, et al. Informational [Page 109]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
Implementers of this specification are encouraged to join the jmp
mailing list in order to participate in discussions on any
clarifications needed and registration proposals for additional
attributes and values being reviewed in order to achieve consensus.
For further information, access the PWG web page under "JMP":
http://www.pwg.org/
Other Participants:
Chuck Adams - Tektronix
Jeff Barnett - IBM
Keith Carter, IBM Corporation
Jeff Copeland - QMS
Andy Davidson - Tektronix
Roger deBry - IBM
Mabry Dozier - QMS
Lee Farrell - Canon
Steve Gebert - IBM
Robert Herriot - Sun Microsystems Inc.
Shige Kanemitsu - Kyocera
David Kellerman - Northlake Software
Rick Landau - Digital
Pete Loya - HP
Ray Lutz - Cognisys
Jay Martin - Underscore
Mike MacKay, Novell, Inc.
Stan McConnell - Xerox
Carl-Uno Manros, Xerox, Corp.
Pat Nogay - IBM
Bob Pentecost - HP
Rob Rhoads - Intel
David Roach - Unisys
Stuart Rowley - Kyocera
Hiroyuki Sato - Canon
Bob Setterbo - Adobe
Gail Songer, EFI
Mike Timperman - Lexmark
Randy Turner - Sharp
William Wagner - Digital Products
Jim Walker - Dazel
Chris Wellens - Interworking Labs
Rob Whittle - Novell
Don Wright - Lexmark
Lloyd Young - Lexmark
Atsushi Yuki - Kyocera
Peter Zehler, Xerox, Corp.
Bergman, et al. Informational [Page 110]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
10 INDEX
This index includes the textual conventions, the objects, and the
attributes. Textual conventions all start with the prefix: "JM" and
end with the suffix: "TC". Objects all starts with the prefix:
"jm" followed by the group name. Attributes are identified with
enums, and so start with any lower case letter and have no special
prefix.
colorantConsumed, 40
colorantRequested, 40
deviceNameRequested, 30
documentCopiesCompleted, 35
documentCopiesRequested, 35
documentFormat, 31
documentFormatIndex, 31
documentName, 31
fileName, 31
finishing, 33
fullColorImpressionsCompleted, 37
highlightColorImpressionsCompleted, 37
impressionsCompletedCurrentCopy, 37
impressionsInterpreted, 37
impressionsSentToDevice, 37
impressionsSpooled, 36
jmAttributeInstanceIndex, 99
jmAttributeTypeIndex, 98
JmAttributeTypeTC, 78
jmAttributeValueAsInteger, 99
jmAttributeValueAsOctets, 100
JmBooleanTC, 72
JmFinishingTC, 70
jmGeneralAttributePersistence, 87
jmGeneralJobPersistence, 87
jmGeneralJobSetIndex, 85
jmGeneralJobSetName, 88
jmGeneralNewestActiveJobIndex, 86
jmGeneralNumberOfActiveJobs, 86
jmGeneralOldestActiveJobIndex, 86
JmJobCollationTypeTC, 74
jmJobIDJobIndex, 91
jmJobIDJobSetIndex, 90
jmJobImpressionsCompleted, 96
jmJobImpressionsPerCopyRequested, 95
jmJobIndex, 92
jmJobKOctetsPerCopyRequested, 94
jmJobKOctetsProcessed, 94
jmJobOwner, 96
Bergman, et al. Informational [Page 111]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
JmJobServiceTypesTC, 81
JmJobSourcePlatformTypeTC, 69
jmJobState, 92
jmJobStateReasons1, 93
JmJobStateReasons1TC, 83
JmJobStateReasons2TC, 83
JmJobStateReasons3TC, 83
JmJobStateReasons4TC, 84
JmJobStateTC, 75
JmJobStringTC, 68
jmJobSubmissionID, 89
JmJobSubmissionIDTypeTC, 74
JmMediumTypeTC, 72
JmNaturalLanguageTagTC, 68
jmNumberOfInterveningJobs, 93
JmPrinterResolutionTC, 71
JmPrintQualityTC, 71
JmTimeStampTC, 69
JmTonerEconomyTC, 72
JmUTF8StringTC, 68
jobAccountName, 27
jobCodedCharSet, 26
jobCollationType, 36
jobComment, 31
jobCompletionTime, 43
jobCopiesCompleted, 35
jobCopiesRequested, 35
jobHold, 33
jobHoldUntil, 33
jobKOctetsTransferred, 35
jobName, 28
jobNaturalLanguageTag, 27
jobOriginatingHost, 30
jobPriority, 32
jobProcessAfterDateAndTime, 32
jobProcessingCPUTime, 43
jobServiceTypes, 29
jobSourceChannelIndex, 29
jobSourcePlatformType, 29
jobStartedBeingHeldTime, 42
jobStartedProcessingTime, 43
jobStateReasons2, 25
jobStateReasons3, 25
jobStateReasons4, 25
jobSubmissionTime, 42
jobSubmissionToServerTime, 42
jobURI, 27
mediumConsumed, 40
Bergman, et al. Informational [Page 112]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
mediumRequested, 39
mediumSizeConsumed, 41
mediumTypeConsumed, 41
numberOfDocuments, 30
other, 25
outputBin, 33
pagesCompleted, 38
pagesCompletedCurrentCopy, 38
pagesRequested, 38
physicalDevice, 30
printerResolutionRequested, 34
printerResolutionUsed, 34
printQualityRequested, 34
printQualityUsed, 34
processingMessage, 25
processingMessageNaturalLangTag, 26
queueNameRequested, 30
serverAssignedJobName, 28
sheetCompletedCopyNumber, 36
sheetCompletedDocumentNumber, 36
sheetsCompleted, 39
sheetsCompletedCurrentCopy, 39
sheetsRequested, 39
sides, 33
submittingApplicationName, 29
submittingServerName, 29
tonerDensityRequested, 34
tonerDensityUsed, 34
tonerEcomonyRequested, 34
tonerEcomonyUsed, 34
Bergman, et al. Informational [Page 113]
RFC 2707 Job Monitoring MIB - V1.0 November 1999
11 Full Copyright Statement
Copyright (C) The Internet Society (1999). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Bergman, et al. Informational [Page 114]
ERRATA
