rfc2934
Network Working Group K. McCloghrie
Request for Comments: 2934 cisco Systems
Category: Experimental D. Farinacci
Procket Networks
D. Thaler
Microsoft
B. Fenner
AT&T Labs
October 2000
Protocol Independent Multicast MIB for IPv4
Status of this Memo
This memo defines an Experimental Protocol for the Internet
community. It does not specify an Internet standard of any kind.
Discussion and suggestions for improvement are requested.
Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2000). All Rights Reserved.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects used for managing the
Protocol Independent Multicast (PIM) protocol for IPv4.
Table of Contents
1 Introduction ................................................. 2
2 The SNMP Network Management Framework ........................ 2
3 Overview ..................................................... 3
4 Definitions .................................................. 4
5 Security Considerations ...................................... 22
6 Intellectual Property Notice ................................. 23
7 Acknowledgements ............................................. 23
8 Authors' Addresses ........................................... 24
9 References ................................................... 24
10 Full Copyright Statement .................................... 27
McCloghrie, et al. Experimental [Page 1]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects used for managing the
Protocol Independent Multicast (PIM) protocol [16,17,18,19]. This
MIB module is applicable to IPv4 multicast routers which implement
PIM. This MIB does not support management of PIM for other address
families, including IPv6. Such management may be supported by other
MIBs.
2. The SNMP Network Management Framework
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2271 [1].
o Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and described in
STD 16, RFC 1155 [2], STD 16, RFC 1212 [3] and RFC 1215 [4].
The second version, called SMIv2, is described in STD 58, RFC
2578 [5], STD 58, RFC 2579 [6] and STD 58, RFC 2580 [7].
o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and
described in STD 15, RFC 1157 [8]. A second version of the SNMP
message protocol, which is not an Internet standards track
protocol, is called SNMPv2c and described in RFC 1901 [9] and
RFC 1906 [10]. The third version of the message protocol is
called SNMPv3 and described in RFC 1906 [10], RFC 2572 [11] and
RFC 2574 [12].
o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is
described in STD 15, RFC 1157 [8]. A second set of protocol
operations and associated PDU formats is described in RFC 1905
[13].
o A set of fundamental applications described in RFC 2573 [14] and
the view-based access control mechanism described in RFC 2575
[15].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
McCloghrie, et al. Experimental [Page 2]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
3. Overview
This MIB module contains one scalar and eight tables. Some of the
objects in these tables are deprecated. This MIB contains deprecated
objects since they are necessary for managing PIMv1 routers, but
PIMv1 itself is obsoleted by PIMv2 [18,19].
The tables contained in this MIB are:
(1) The PIM Interface Table contains one row for each of the
router's PIM interfaces.
(2) The PIM Neighbor Table contains one row for each of the router's
PIM neighbors.
(3) The PIM IP Multicast Route Table contains one row for each
multicast routing entry whose incoming interface is running PIM.
(4) The PIM Next Hop Table which contains one row for each outgoing
interface list entry in the multicast routing table whose
interface is running PIM, and whose state is pruned.
(5) The (deprecated) PIM RP Table contains the PIM (version 1)
information for IP multicast groups which is common to all RPs
of a group.
(6) The PIM RP-Set Table contains the PIM (version 2) information
for sets of candidate Rendezvous Points (RPs) for IP multicast
group addresses with particular address prefixes.
(7) The PIM Candidate-RP Table contains the IP multicast groups for
which the local router is to advertise itself as a Candidate-RP.
If this table is empty, then the local router advertises itself
as a Candidate-RP for all groups.
(8) The PIM Component Table contains one row for each of the PIM
domains to which the router is connected.
McCloghrie, et al. Experimental [Page 3]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
4. Definitions
PIM-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, experimental,
NOTIFICATION-TYPE,
Integer32, IpAddress, TimeTicks FROM SNMPv2-SMI
RowStatus, TruthValue FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF
ipMRouteGroup, ipMRouteSource,
ipMRouteSourceMask, ipMRouteNextHopGroup,
ipMRouteNextHopSource, ipMRouteNextHopSourceMask,
ipMRouteNextHopIfIndex,
ipMRouteNextHopAddress FROM IPMROUTE-STD-MIB
InterfaceIndex FROM IF-MIB;
pimMIB MODULE-IDENTITY
LAST-UPDATED "200009280000Z" -- September 28, 2000
ORGANIZATION "IETF IDMR Working Group."
CONTACT-INFO
" Dave Thaler
Microsoft Corporation
One Microsoft Way
Redmond, WA 98052-6399
US
Phone: +1 425 703 8835
EMail: dthaler@microsoft.com"
DESCRIPTION
"The MIB module for management of PIM routers."
REVISION "200009280000Z" -- September 28, 2000
DESCRIPTION
"Initial version, published as RFC 2934."
::= { experimental 61 }
pimMIBObjects OBJECT IDENTIFIER ::= { pimMIB 1 }
pimTraps OBJECT IDENTIFIER ::= { pimMIBObjects 0 }
pim OBJECT IDENTIFIER ::= { pimMIBObjects 1 }
pimJoinPruneInterval OBJECT-TYPE
SYNTAX Integer32
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
McCloghrie, et al. Experimental [Page 4]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
DESCRIPTION
"The default interval at which periodic PIM-SM Join/Prune
messages are to be sent."
::= { pim 1 }
-- The PIM Interface Table
pimInterfaceTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the router's PIM interfaces.
IGMP and PIM are enabled on all interfaces listed in this
table."
::= { pim 2 }
pimInterfaceEntry OBJECT-TYPE
SYNTAX PimInterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimInterfaceTable."
INDEX { pimInterfaceIfIndex }
::= { pimInterfaceTable 1 }
PimInterfaceEntry ::= SEQUENCE {
pimInterfaceIfIndex InterfaceIndex,
pimInterfaceAddress IpAddress,
pimInterfaceNetMask IpAddress,
pimInterfaceMode INTEGER,
pimInterfaceDR IpAddress,
pimInterfaceHelloInterval Integer32,
pimInterfaceStatus RowStatus,
pimInterfaceJoinPruneInterval Integer32,
pimInterfaceCBSRPreference Integer32
}
pimInterfaceIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ifIndex value of this PIM interface."
::= { pimInterfaceEntry 1 }
pimInterfaceAddress OBJECT-TYPE
SYNTAX IpAddress
McCloghrie, et al. Experimental [Page 5]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of the PIM interface."
::= { pimInterfaceEntry 2 }
pimInterfaceNetMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network mask for the IP address of the PIM interface."
::= { pimInterfaceEntry 3 }
pimInterfaceMode OBJECT-TYPE
SYNTAX INTEGER { dense(1), sparse(2), sparseDense(3) }
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The configured mode of this PIM interface. A value of
sparseDense is only valid for PIMv1."
DEFVAL { dense }
::= { pimInterfaceEntry 4 }
pimInterfaceDR OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Designated Router on this PIM interface. For point-to-
point interfaces, this object has the value 0.0.0.0."
::= { pimInterfaceEntry 5 }
pimInterfaceHelloInterval OBJECT-TYPE
SYNTAX Integer32
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The frequency at which PIM Hello messages are transmitted
on this interface."
DEFVAL { 30 }
::= { pimInterfaceEntry 6 }
pimInterfaceStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
McCloghrie, et al. Experimental [Page 6]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
STATUS current
DESCRIPTION
"The status of this entry. Creating the entry enables PIM
on the interface; destroying the entry disables PIM on the
interface."
::= { pimInterfaceEntry 7 }
pimInterfaceJoinPruneInterval OBJECT-TYPE
SYNTAX Integer32
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The frequency at which PIM Join/Prune messages are
transmitted on this PIM interface. The default value of
this object is the pimJoinPruneInterval."
::= { pimInterfaceEntry 8 }
pimInterfaceCBSRPreference OBJECT-TYPE
SYNTAX Integer32 (-1..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The preference value for the local interface as a candidate
bootstrap router. The value of -1 is used to indicate that
the local interface is not a candidate BSR interface."
DEFVAL { 0 }
::= { pimInterfaceEntry 9 }
-- The PIM Neighbor Table
pimNeighborTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the router's PIM neighbors."
::= { pim 3 }
pimNeighborEntry OBJECT-TYPE
SYNTAX PimNeighborEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimNeighborTable."
INDEX { pimNeighborAddress }
::= { pimNeighborTable 1 }
McCloghrie, et al. Experimental [Page 7]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
PimNeighborEntry ::= SEQUENCE {
pimNeighborAddress IpAddress,
pimNeighborIfIndex InterfaceIndex,
pimNeighborUpTime TimeTicks,
pimNeighborExpiryTime TimeTicks,
pimNeighborMode INTEGER
}
pimNeighborAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP address of the PIM neighbor for which this entry
contains information."
::= { pimNeighborEntry 1 }
pimNeighborIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of ifIndex for the interface used to reach this
PIM neighbor."
::= { pimNeighborEntry 2 }
pimNeighborUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time since this PIM neighbor (last) became a neighbor
of the local router."
::= { pimNeighborEntry 3 }
pimNeighborExpiryTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum time remaining before this PIM neighbor will be
aged out."
::= { pimNeighborEntry 4 }
pimNeighborMode OBJECT-TYPE
SYNTAX INTEGER { dense(1), sparse(2) }
MAX-ACCESS read-only
STATUS deprecated
McCloghrie, et al. Experimental [Page 8]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
DESCRIPTION
"The active PIM mode of this neighbor. This object is
deprecated for PIMv2 routers since all neighbors on the
interface must be either dense or sparse as determined by
the protocol running on the interface."
::= { pimNeighborEntry 5 }
--
-- The PIM IP Multicast Route Table
--
pimIpMRouteTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimIpMRouteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing PIM-specific information on
a subset of the rows of the ipMRouteTable defined in the IP
Multicast MIB."
::= { pim 4 }
pimIpMRouteEntry OBJECT-TYPE
SYNTAX PimIpMRouteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimIpMRouteTable. There
is one entry per entry in the ipMRouteTable whose incoming
interface is running PIM."
INDEX { ipMRouteGroup, ipMRouteSource, ipMRouteSourceMask }
::= { pimIpMRouteTable 1 }
PimIpMRouteEntry ::= SEQUENCE {
pimIpMRouteUpstreamAssertTimer TimeTicks,
pimIpMRouteAssertMetric Integer32,
pimIpMRouteAssertMetricPref Integer32,
pimIpMRouteAssertRPTBit TruthValue,
pimIpMRouteFlags BITS
}
pimIpMRouteUpstreamAssertTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time remaining before the router changes its upstream
neighbor back to its RPF neighbor. This timer is called the
Assert timer in the PIM Sparse and Dense mode specification.
McCloghrie, et al. Experimental [Page 9]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
A value of 0 indicates that no Assert has changed the
upstream neighbor away from the RPF neighbor."
::= { pimIpMRouteEntry 1 }
pimIpMRouteAssertMetric OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The metric advertised by the assert winner on the upstream
interface, or 0 if no such assert is in received."
::= { pimIpMRouteEntry 2 }
pimIpMRouteAssertMetricPref OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The preference advertised by the assert winner on the
upstream interface, or 0 if no such assert is in effect."
::= { pimIpMRouteEntry 3 }
pimIpMRouteAssertRPTBit OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of the RPT-bit advertised by the assert winner on
the upstream interface, or false if no such assert is in
effect."
::= { pimIpMRouteEntry 4 }
pimIpMRouteFlags OBJECT-TYPE
SYNTAX BITS {
rpt(0),
spt(1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object describes PIM-specific flags related to a
multicast state entry. See the PIM Sparse Mode
specification for the meaning of the RPT and SPT bits."
::= { pimIpMRouteEntry 5 }
--
-- The PIM Next Hop Table
--
McCloghrie, et al. Experimental [Page 10]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
pimIpMRouteNextHopTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimIpMRouteNextHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing PIM-specific information on
a subset of the rows of the ipMRouteNextHopTable defined in
the IP Multicast MIB."
::= { pim 7 }
pimIpMRouteNextHopEntry OBJECT-TYPE
SYNTAX PimIpMRouteNextHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimIpMRouteNextHopTable.
There is one entry per entry in the ipMRouteNextHopTable
whose interface is running PIM and whose
ipMRouteNextHopState is pruned(1)."
INDEX { ipMRouteNextHopGroup, ipMRouteNextHopSource,
ipMRouteNextHopSourceMask, ipMRouteNextHopIfIndex,
ipMRouteNextHopAddress }
::= { pimIpMRouteNextHopTable 1 }
PimIpMRouteNextHopEntry ::= SEQUENCE {
pimIpMRouteNextHopPruneReason INTEGER
}
pimIpMRouteNextHopPruneReason OBJECT-TYPE
SYNTAX INTEGER {
other (1),
prune (2),
assert (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates why the downstream interface was
pruned, whether in response to a PIM prune message or due to
PIM Assert processing."
::= { pimIpMRouteNextHopEntry 2 }
-- The PIM RP Table
pimRPTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimRPEntry
MAX-ACCESS not-accessible
STATUS deprecated
McCloghrie, et al. Experimental [Page 11]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
DESCRIPTION
"The (conceptual) table listing PIM version 1 information
for the Rendezvous Points (RPs) for IP multicast groups.
This table is deprecated since its function is replaced by
the pimRPSetTable for PIM version 2."
::= { pim 5 }
pimRPEntry OBJECT-TYPE
SYNTAX PimRPEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"An entry (conceptual row) in the pimRPTable. There is one
entry per RP address for each IP multicast group."
INDEX { pimRPGroupAddress, pimRPAddress }
::= { pimRPTable 1 }
PimRPEntry ::= SEQUENCE {
pimRPGroupAddress IpAddress,
pimRPAddress IpAddress,
pimRPState INTEGER,
pimRPStateTimer TimeTicks,
pimRPLastChange TimeTicks,
pimRPRowStatus RowStatus
}
pimRPGroupAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The IP multicast group address for which this entry
contains information about an RP."
::= { pimRPEntry 1 }
pimRPAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The unicast address of the RP."
::= { pimRPEntry 2 }
pimRPState OBJECT-TYPE
SYNTAX INTEGER { up(1), down(2) }
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
McCloghrie, et al. Experimental [Page 12]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
"The state of the RP."
::= { pimRPEntry 3 }
pimRPStateTimer OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The minimum time remaining before the next state change.
When pimRPState is up, this is the minimum time which must
expire until it can be declared down. When pimRPState is
down, this is the time until it will be declared up (in
order to retry)."
::= { pimRPEntry 4 }
pimRPLastChange OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The value of sysUpTime at the time when the corresponding
instance of pimRPState last changed its value."
::= { pimRPEntry 5 }
pimRPRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The status of this row, by which new entries may be
created, or old entries deleted from this table."
::= { pimRPEntry 6 }
-- The PIM RP-Set Table
pimRPSetTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimRPSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing PIM information for
candidate Rendezvous Points (RPs) for IP multicast groups.
When the local router is the BSR, this information is
obtained from received Candidate-RP-Advertisements. When
the local router is not the BSR, this information is
obtained from received RP-Set messages."
::= { pim 6 }
McCloghrie, et al. Experimental [Page 13]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
pimRPSetEntry OBJECT-TYPE
SYNTAX PimRPSetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimRPSetTable."
INDEX { pimRPSetComponent, pimRPSetGroupAddress,
pimRPSetGroupMask, pimRPSetAddress }
::= { pimRPSetTable 1 }
PimRPSetEntry ::= SEQUENCE {
pimRPSetGroupAddress IpAddress,
pimRPSetGroupMask IpAddress,
pimRPSetAddress IpAddress,
pimRPSetHoldTime Integer32,
pimRPSetExpiryTime TimeTicks,
pimRPSetComponent Integer32
}
pimRPSetGroupAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP multicast group address which, when combined with
pimRPSetGroupMask, gives the group prefix for which this
entry contains information about the Candidate-RP."
::= { pimRPSetEntry 1 }
pimRPSetGroupMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The multicast group address mask which, when combined with
pimRPSetGroupAddress, gives the group prefix for which this
entry contains information about the Candidate-RP."
::= { pimRPSetEntry 2 }
pimRPSetAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP address of the Candidate-RP."
::= { pimRPSetEntry 3 }
McCloghrie, et al. Experimental [Page 14]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
pimRPSetHoldTime OBJECT-TYPE
SYNTAX Integer32 (0..255)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The holdtime of a Candidate-RP. If the local router is not
the BSR, this value is 0."
::= { pimRPSetEntry 4 }
pimRPSetExpiryTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum time remaining before the Candidate-RP will be
declared down. If the local router is not the BSR, this
value is 0."
::= { pimRPSetEntry 5 }
pimRPSetComponent OBJECT-TYPE
SYNTAX Integer32 (1..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
" A number uniquely identifying the component. Each
protocol instance connected to a separate domain should have
a different index value."
::= { pimRPSetEntry 6 }
--
-- Note: { pim 8 } through { pim 10 } were used in older versions
-- of this MIB. Since some earlier versions of this MIB have been
-- widely-deployed, these values must not be used in the future,
-- as long the MIB is rooted under { experimental 61 }.
--
-- The PIM Candidate-RP Table
pimCandidateRPTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimCandidateRPEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table listing the IP multicast groups for
which the local router is to advertise itself as a
Candidate-RP when the value of pimComponentCRPHoldTime is
non-zero. If this table is empty, then the local router
McCloghrie, et al. Experimental [Page 15]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
will advertise itself as a Candidate-RP for all groups
(providing the value of pimComponentCRPHoldTime is non-
zero)."
::= { pim 11 }
pimCandidateRPEntry OBJECT-TYPE
SYNTAX PimCandidateRPEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimCandidateRPTable."
INDEX { pimCandidateRPGroupAddress,
pimCandidateRPGroupMask }
::= { pimCandidateRPTable 1 }
PimCandidateRPEntry ::= SEQUENCE {
pimCandidateRPGroupAddress IpAddress,
pimCandidateRPGroupMask IpAddress,
pimCandidateRPAddress IpAddress,
pimCandidateRPRowStatus RowStatus
}
pimCandidateRPGroupAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP multicast group address which, when combined with
pimCandidateRPGroupMask, identifies a group prefix for which
the local router will advertise itself as a Candidate-RP."
::= { pimCandidateRPEntry 1 }
pimCandidateRPGroupMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The multicast group address mask which, when combined with
pimCandidateRPGroupMask, identifies a group prefix for which
the local router will advertise itself as a Candidate-RP."
::= { pimCandidateRPEntry 2 }
pimCandidateRPAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The (unicast) address of the interface which will be
McCloghrie, et al. Experimental [Page 16]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
advertised as a Candidate-RP."
::= { pimCandidateRPEntry 3 }
pimCandidateRPRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this row, by which new entries may be
created, or old entries deleted from this table."
::= { pimCandidateRPEntry 4 }
-- The PIM Component Table
pimComponentTable OBJECT-TYPE
SYNTAX SEQUENCE OF PimComponentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The (conceptual) table containing objects specific to a PIM
domain. One row exists for each domain to which the router
is connected. A PIM-SM domain is defined as an area of the
network over which Bootstrap messages are forwarded.
Typically, a PIM-SM router will be a member of exactly one
domain. This table also supports, however, routers which
may form a border between two PIM-SM domains and do not
forward Bootstrap messages between them."
::= { pim 12 }
pimComponentEntry OBJECT-TYPE
SYNTAX PimComponentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry (conceptual row) in the pimComponentTable."
INDEX { pimComponentIndex }
::= { pimComponentTable 1 }
PimComponentEntry ::= SEQUENCE {
pimComponentIndex Integer32,
pimComponentBSRAddress IpAddress,
pimComponentBSRExpiryTime TimeTicks,
pimComponentCRPHoldTime Integer32,
pimComponentStatus RowStatus
}
pimComponentIndex OBJECT-TYPE
SYNTAX Integer32 (1..255)
McCloghrie, et al. Experimental [Page 17]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A number uniquely identifying the component. Each protocol
instance connected to a separate domain should have a
different index value. Routers that only support membership
in a single PIM-SM domain should use a pimComponentIndex
value of 1."
::= { pimComponentEntry 1 }
pimComponentBSRAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IP address of the bootstrap router (BSR) for the local
PIM region."
::= { pimComponentEntry 2 }
pimComponentBSRExpiryTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum time remaining before the bootstrap router in
the local domain will be declared down. For candidate BSRs,
this is the time until the component sends an RP-Set
message. For other routers, this is the time until it may
accept an RP-Set message from a lower candidate BSR."
::= { pimComponentEntry 3 }
pimComponentCRPHoldTime OBJECT-TYPE
SYNTAX Integer32 (0..255)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The holdtime of the component when it is a candidate RP in
the local domain. The value of 0 is used to indicate that
the local system is not a Candidate-RP."
DEFVAL { 0 }
::= { pimComponentEntry 4 }
pimComponentStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
McCloghrie, et al. Experimental [Page 18]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
"The status of this entry. Creating the entry creates
another protocol instance; destroying the entry disables a
protocol instance."
::= { pimComponentEntry 5 }
-- PIM Traps
pimNeighborLoss NOTIFICATION-TYPE
OBJECTS {
pimNeighborIfIndex
}
STATUS current
DESCRIPTION
"A pimNeighborLoss trap signifies the loss of an adjacency
with a neighbor. This trap should be generated when the
neighbor timer expires, and the router has no other
neighbors on the same interface with a lower IP address than
itself."
::= { pimTraps 1 }
-- conformance information
pimMIBConformance OBJECT IDENTIFIER ::= { pimMIB 2 }
pimMIBCompliances OBJECT IDENTIFIER ::= { pimMIBConformance 1 }
pimMIBGroups OBJECT IDENTIFIER ::= { pimMIBConformance 2 }
-- compliance statements
pimV1MIBCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for routers running PIMv1 and
implementing the PIM MIB."
MODULE -- this module
MANDATORY-GROUPS { pimV1MIBGroup }
::= { pimMIBCompliances 1 }
pimSparseV2MIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for routers running PIM Sparse
Mode and implementing the PIM MIB."
MODULE -- this module
MANDATORY-GROUPS { pimV2MIBGroup }
GROUP pimV2CandidateRPMIBGroup
McCloghrie, et al. Experimental [Page 19]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
DESCRIPTION
"This group is mandatory if the router is capable of being a
Candidate RP."
OBJECT pimInterfaceStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { pimMIBCompliances 2 }
pimDenseV2MIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for routers running PIM Dense Mode
and implementing the PIM MIB."
MODULE -- this module
MANDATORY-GROUPS { pimDenseV2MIBGroup }
OBJECT pimInterfaceStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { pimMIBCompliances 3 }
-- units of conformance
pimNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS { pimNeighborLoss }
STATUS current
DESCRIPTION
"A collection of notifications for signaling important PIM
events."
::= { pimMIBGroups 1 }
pimV2MIBGroup OBJECT-GROUP
OBJECTS { pimJoinPruneInterval, pimNeighborIfIndex,
pimNeighborUpTime, pimNeighborExpiryTime,
pimInterfaceAddress, pimInterfaceNetMask,
pimInterfaceDR, pimInterfaceHelloInterval,
pimInterfaceStatus, pimInterfaceJoinPruneInterval,
pimInterfaceCBSRPreference, pimInterfaceMode,
pimRPSetHoldTime, pimRPSetExpiryTime,
pimComponentBSRAddress, pimComponentBSRExpiryTime,
pimComponentCRPHoldTime, pimComponentStatus,
pimIpMRouteFlags, pimIpMRouteUpstreamAssertTimer
McCloghrie, et al. Experimental [Page 20]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
}
STATUS current
DESCRIPTION
"A collection of objects to support management of PIM Sparse
Mode (version 2) routers."
::= { pimMIBGroups 2 }
pimDenseV2MIBGroup OBJECT-GROUP
OBJECTS { pimNeighborIfIndex,
pimNeighborUpTime, pimNeighborExpiryTime,
pimInterfaceAddress, pimInterfaceNetMask,
pimInterfaceDR, pimInterfaceHelloInterval,
pimInterfaceStatus, pimInterfaceMode
}
STATUS current
DESCRIPTION
"A collection of objects to support management of PIM Dense
Mode (version 2) routers."
::= { pimMIBGroups 5 }
pimV2CandidateRPMIBGroup OBJECT-GROUP
OBJECTS { pimCandidateRPAddress,
pimCandidateRPRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects to support configuration of which
groups a router is to advertise itself as a Candidate-RP."
::= { pimMIBGroups 3 }
pimV1MIBGroup OBJECT-GROUP
OBJECTS { pimJoinPruneInterval, pimNeighborIfIndex,
pimNeighborUpTime, pimNeighborExpiryTime,
pimNeighborMode,
pimInterfaceAddress, pimInterfaceNetMask,
pimInterfaceJoinPruneInterval, pimInterfaceStatus,
pimInterfaceMode, pimInterfaceDR,
pimInterfaceHelloInterval,
pimRPState, pimRPStateTimer,
pimRPLastChange, pimRPRowStatus
}
STATUS deprecated
DESCRIPTION
"A collection of objects to support management of PIM
(version 1) routers."
::= { pimMIBGroups 4 }
pimNextHopGroup OBJECT-GROUP
McCloghrie, et al. Experimental [Page 21]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
OBJECTS { pimIpMRouteNextHopPruneReason }
STATUS current
DESCRIPTION
"A collection of optional objects to provide per-next hop
information for diagnostic purposes. Supporting this group
may add a large number of instances to a tree walk, but the
information in this group can be extremely useful in
tracking down multicast connectivity problems."
::= { pimMIBGroups 6 }
pimAssertGroup OBJECT-GROUP
OBJECTS { pimIpMRouteAssertMetric, pimIpMRouteAssertMetricPref,
pimIpMRouteAssertRPTBit }
STATUS current
DESCRIPTION
"A collection of optional objects to provide extra
information about the assert election process. There is no
protocol reason to keep such information, but some
implementations may already keep this information and make
it available. These objects can also be very useful in
debugging connectivity or duplicate packet problems,
especially if the assert winner does not support the PIM and
IP Multicast MIBs."
::= { pimMIBGroups 7 }
END
5. Security Considerations
This MIB contains readable objects whose values provide information
related to multicast routing, including information on the network
topology. There are also a number of objects that have a MAX-ACCESS
clause of read-write and/or read-create, which allow an administrator
to configure PIM in the router.
While unauthorized access to the readable objects is relatively
innocuous, unauthorized access to the write-able objects could cause
a denial of service. Hence, the support for SET operations in a
non-secure environment without proper protection can have a negative
effect on network operations.
SNMPv1 by itself is such an insecure environment. Even if the
network itself is secure (for example by using IPSec), even then,
there is no control as to who on the secure network is allowed to
access and SET (change/create/delete) the objects in this MIB.
McCloghrie, et al. Experimental [Page 22]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
It is recommended that the implementers consider the security
features as provided by the SNMPv3 framework. Specifically, the use
of the User-based Security Model RFC 2274 [12] and the View-based
Access Control Model RFC 2275 [15] is recommended.
It is then a customer/user responsibility to ensure that the SNMP
entity giving access to this MIB, is properly configured to give
access to those objects only to those principals (users) that have
legitimate rights to access them.
6. Intellectual Property Notice
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such
proprietary rights by implementers or users of this specification can
be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
7. Acknowledgements
This MIB module has been updated based on feedback from the IETF's
Inter-Domain Multicast Routing (IDMR) Working Group.
McCloghrie, et al. Experimental [Page 23]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
8. Authors' Addresses
Keith McCloghrie
cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
Phone: +1 408 526 5260
EMail: kzm@cisco.com
Dino Farinacci
Procket Networks
3850 North First Street
San Jose, CA 95134
Phone: +1 408-954-7909
Email: dino@procket.com
Dave Thaler
Microsoft Corporation
One Microsoft Way
Redmond, WA 98052-6399
Phone: +1 425 703 8835
EMail: dthaler@microsoft.com
Bill Fenner
AT&T Labs - Research
75 Willow Rd.
Menlo Park, CA 94025
Phone: +1 650 330 7893
EMail: fenner@research.att.com
9. References
[1] Wijnen, B., Harrington, D. and R. Presuhn, "An Architecture for
Describing SNMP Management Frameworks", RFC 2571, April 1999.
[2] Rose, M. and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based Internets", STD 16, RFC
1155, May 1990.
[3] Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD 16,
RFC 1212, March 1991.
McCloghrie, et al. Experimental [Page 24]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
[4] Rose, M., "A Convention for Defining Traps for use with the
SNMP", RFC 1215, March 1991.
[5] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
M. and S. Waldbusser, "Structure of Management Information
Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[6] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
M. and S. Waldbusser, "Textual Conventions for SMIv2", STD 58,
RFC 2579, April 1999.
[7] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
M. and S. Waldbusser, "Conformance Statements for SMIv2", STD
58, RFC 2580, April 1999.
[8] Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, May 1990.
[9] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901, January
1996.
[10] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Transport
Mappings for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1906, January 1996.
[11] Case, J., Harrington D., Presuhn R. and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, April 1999.
[12] Blumenthal, U. and B. Wijnen, "User-based Security Model (USM)
for version 3 of the Simple Network Management Protocol
(SNMPv3)", RFC 2574, April 1999.
[13] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Protocol
Operations for Version 2 of the Simple Network Management
Protocol (SNMPv2)", RFC 1905, January 1996.
[14] Levi, D., Meyer, P. and B. Stewart, "SNMPv3 Applications", RFC
2573, April 1999.
[15] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based Access
Control Model (VACM) for the Simple Network Management Protocol
(SNMP)", RFC 2575, April 1999.
[16] Deering, S., Estrin, D., Farinacci, D., Jacobson, V., Liu, G.
and L. Wei, "Protocol Independent Multicast (PIM): Motivation
and Architecture", Work in Progress.
McCloghrie, et al. Experimental [Page 25]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
[17] Deering, S., Estrin, D., Farinacci, D., Jacobson, V., Liu, G.
and L. Wei, "Protocol Independent Multicast (PIM): Protocol
Specification", Work in Progress.
[18] Estrin, D., Farinacci, D., Helmy, A., Thaler, D., Deering, S.,
Handley, M., Jacobson, V., Liu, C., Sharma, P. and L. Wei,
"Protocol Independent Multicast - Sparse Mode (PIM-SM): Protocol
Specification", RFC 2362, June 1998.
[19] Deering, S., Estrin, D., Farinacci, D., Jacobson, V., Helmy, A.
and L. Wei, "Protocol Independent Multicast Version 2, Dense
Mode Specification", Work in Progress.
[20] McCloghrie, K., Farinacci, D. and D. Thaler, "IPv4 Multicast
Routing MIB", RFC 2932, October 2000.
McCloghrie, et al. Experimental [Page 26]
RFC 2934 Protocol Independent Multicast MIB for IPv4 October 2000
10. Full Copyright Statement
Copyright (C) The Internet Society (2000). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
McCloghrie, et al. Experimental [Page 27]
ERRATA
