rfc4359
Network Working Group B. Weis
Request for Comments: 4359 Cisco Systems
Category: Standards Track January 2006
The Use of RSA/SHA-1 Signatures within
Encapsulating Security Payload (ESP) and Authentication Header (AH)
Status of This Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2006).
Abstract
This memo describes the use of the RSA digital signature algorithm as
an authentication algorithm within the revised IP Encapsulating
Security Payload (ESP) as described in RFC 4303 and the revised IP
Authentication Header (AH) as described in RFC 4302. The use of a
digital signature algorithm, such as RSA, provides data origin
authentication in applications when a secret key method (e.g., HMAC)
does not provide this property. One example is the use of ESP and AH
to authenticate the sender of an IP multicast packet.
Weis Standards Track [Page 1]
RFC 4359 RSA/SHA-1 Signatures within ESP and AH January 2006
Table of Contents
1. Introduction ....................................................2
2. Algorithm and Mode ..............................................3
2.1. Key Size Discussion ........................................4
3. Performance .....................................................5
4. Interaction with the ESP Cipher Mechanism .......................6
5. Key Management Considerations ...................................6
6. Security Considerations .........................................7
6.1. Eavesdropping ..............................................7
6.2. Replay .....................................................7
6.3. Message Insertion ..........................................8
6.4. Deletion ...................................................8
6.5. Modification ...............................................8
6.6. Man in the Middle ..........................................8
6.7. Denial of Service ..........................................8
7. IANA Considerations .............................................9
8. Acknowledgements ...............................................10
9. References .....................................................10
9.1. Normative References ......................................10
9.2. Informative References ....................................10
1. Introduction
Encapsulating Security Payload (ESP) [ESP] and Authentication Header
(AH) [AH] headers can be used to protect both unicast traffic and
group (e.g., IPv4 and IPv6 multicast) traffic. When unicast traffic
is protected between a pair of entities, HMAC transforms (such as
[HMAC-SHA]) are sufficient to prove data origin authentication. An
HMAC is sufficient protection in that scenario because only the two
entities involved in the communication have access to the key, and
proof-of-possession of the key in the HMAC construct authenticates
the sender. However, when ESP and AH authenticate group traffic,
this property no longer holds because all group members share the
single HMAC key. In the group case, the identity of the sender is
not uniquely established, since any of the key holders has the
ability to form the HMAC transform. Although the HMAC transform
establishes a group-level security property, data origin
authentication is not achieved.
Some group applications require true data origin authentication,
where one group member cannot successfully impersonate another group
member. The use of asymmetric digital signature algorithms, such as
RSA, can provide true data origin authentication.
With asymmetric algorithms, the sender generates a pair of keys, one
of which is never shared (called the "private key") and one of which
is distributed to other group members (called the "public key").
Weis Standards Track [Page 2]
RFC 4359 RSA/SHA-1 Signatures within ESP and AH January 2006
When the private key is used to sign the output of a cryptographic
hash algorithm, the result is called a "digital signature". A
receiver of the digital signature uses the public key, the signature
value, and an independently computed hash to determine whether or not
the claimed origin of the packet is correct.
This memo describes how RSA digital signatures can be applied as an
ESP and AH authentication mechanism to provide data origin
authentication.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
NOT","SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in
this document are to be interpreted as described in [RFC2119].
2. Algorithm and Mode
The RSA Public Key Algorithm [RSA] is a widely deployed public key
algorithm commonly used for digital signatures. Compared to other
public key algorithms, signature verification is relatively
efficient. This property is useful for groups where receivers may
have limited processing capabilities. The RSA algorithm is commonly
supported in hardware.
Two digital signature encoding methods are supported in [RSA].
RSASSA-PKCS1-v1_5 MUST be supported by a conforming implementation.
RSASSA-PSS is generally believed to be more secure, but at the time
of this writing is not ubiquitous. RSASSA-PSS SHOULD be used
whenever it is available. SHA-1 [SHA] MUST be used as the signature
hash algorithm used by the RSA digital signature algorithm.
When specified for ESP, the Integrity Check Value (ICV) is equal in
size to the RSA modulus, unless the RSA modulus is not a multiple of
8 bits. In this case, the ICV MUST be prepended with between 1 and 7
bits set to zero such that the ICV is a multiple of 8 bits. This
specification matches the output S [RSA, Section 8.1.1] (RSASSA-PSS)
and [RSA, Section 8.2.1] (RSASSA-PKCS1-v1_5) when the RSA modulus is
not a multiple of 8 bits. No implicit ESP ICV Padding bits are
necessary.
When specified for AH, the ICV is equal in size of the RSA modulus,
unless the RSA modulus is not a multiple of 32 bits (IPv4) or 64 bits
(IPv6) [AH, Section 2.6]. In this case, explicit ICV Padding bits
are necessary to create a suitably sized ICV [AH, Section 3.3.3.2.1].
The distribution mechanism of the RSA public key and its replacement
interval are a group policy matter. The use of an ephemeral key pair
with a lifetime of the ESP or AH Security Association (SA) is
RECOMMENDED. This recommended policy reduces the exposure of the RSA
Weis Standards Track [Page 3]
RFC 4359 RSA/SHA-1 Signatures within ESP and AH January 2006
private key to the lifetime of the data being signed by the private
key. Also, this obviates the need to revoke or transmit the validity
period of the key pair.
Digital signature generation is performed as described in [RSA,
Section 8.1.1] (RSASSA-PSS) and [RSA, Section 8.2.1](RSASSA-PKCS1-
v1_5). The authenticated portion of the AH or ESP packet ([AH,
Section 3.3.3], [ESP, Section 3.3.2]) is used as the message M, which
is passed to the signature generation function. The signer's RSA
private key is passed as K. Summarizing, the signature generation
process computes a SHA-1 hash of the authenticated packet bytes,
signs the SHA-1 hash using the private key, and encodes the result
with the specified RSA encoding type. This process results in a
value S, which is known as the ICV in AH and ESP.
Digital signature verification is performed as described in [RSA,
Section 8.1.2] (RSASSA-PSS) and [RSA, Section 8.2.2]
(RSASSA-PKCS1-v1_5). Upon receipt, the ICV is passed to the
verification function as S. The authenticated portion of the AH or
ESP packet is used as the message M, and the RSA public key is passed
as (n, e). In summary, the verification function computes a SHA-1
hash of the authenticated packet bytes, decrypts the SHA-1 hash in
the ICV, and validates that the appropriate encoding was applied and
was correct. The two SHA-1 hashes are compared, and if they are
identical the validation is successful.
2.1. Key Size Discussion
The choice of RSA modulus size must be made carefully. If too small
of a modulus size is chosen, an attacker may be able to reconstruct
the private key used to sign packets before the key is no longer used
by the sender to sign packets. This order of events may result in
the data origin authentication property being compromised. However,
choosing a modulus size larger than necessary will result in an
unnecessarily high cost of CPU cycles for the sender and all
receivers of the packet.
A conforming implementation MUST support a modulus size of 1024 bits.
Recent guidance [TWIRL, RSA-TR] on key sizes makes estimates as to
the amount of effort an attacker would need to expend in order to
reconstruct an RSA private key. Table 1 summarizes the maximum
length of time that selected modulus sizes should be used. Note that
these recommendations are based on factors such as the cost of
processing and memory, as well as cryptographic analysis methods,
which were current at the time these documents were published. As
those factors change, choices of key lifetimes should take them into
account.
Weis Standards Track [Page 4]
RFC 4359 RSA/SHA-1 Signatures within ESP and AH January 2006
Number of Recommended Maximum
Modulus Bits Lifetime
------------ -------------------
768 1 week
1024 1 year
Table 1. RSA Key Use Lifetime Recommendations
3. Performance
The RSA asymmetric key algorithm is very costly in terms of
processing time compared to the HMAC algorithms. However, processing
cost is decreasing over time. Faster general-purpose processors are
being deployed, faster software implementations are being developed,
and hardware acceleration support for the algorithm is becoming more
prevalent.
Care should be taken that RSA signatures are not used for
applications when potential receivers are known to lack sufficient
processing power to verify the signature. It is also important to
use this scheme judiciously when any receiver may be battery powered.
The RSA asymmetric key algorithm is best suited to protect network
traffic for which:
o The sender has a substantial amount of processing power, and
o The network traffic is small enough that adding a relatively large
authentication tag (in the range of 62 to 256 bytes) does not
cause packet fragmentation.
RSA key pair generation and signing are substantially more expensive
operations than signature verification, but these are isolated to the
sender.
The size of the RSA modulus affects the processing required to create
and verify RSA digital signatures. Care should be taken to determine
the size of modulus needed for the application. Smaller modulus
sizes may be chosen as long as the network traffic protected by the
private key flows for less time than it is estimated that an attacker
would take to discover the private key. This lifetime is
considerably smaller than most public key applications that store the
signed data for a period of time. But since the digital signature is
used only for sender verification purposes, a modulus that is
considered weak in another context may be satisfactory.
Weis Standards Track [Page 5]
RFC 4359 RSA/SHA-1 Signatures within ESP and AH January 2006
The size of the RSA public exponent can affect the processing
required to verify RSA digital signatures. Low-exponent RSA
signatures may result in a lower verification processing cost. At
the time of this writing, no attacks are known against low-exponent
RSA signatures that would allow an attacker to create a valid
signature using the RSAES-OAEP scheme.
The addition of a digital signature as an authentication tag adds a
significant number of bytes to the packet. This increases the
likelihood that the packet encapsulated in ESP or AH may be
fragmented.
4. Interaction with the ESP Cipher Mechanism
The RSA signature algorithm cannot be used with an ESP Combined Mode
algorithm that includes an explicit ICV. The Combined Mode algorithm
will add the ESP ICV field, which does not allow use of a separate
authentication algorithm to add the ESP ICV field. One example of
such an algorithm is the ESP Galois/Counter Mode algorithm [AES-GCM].
5. Key Management Considerations
Key management mechanisms negotiating the use of RSA signatures MUST
include the length of the RSA modulus during policy negotiation using
the Authentication Key Length SA Attribute. This gives a device the
opportunity to decline use of the algorithm. This is especially
important for devices with constrained processors that might not be
able to verify signatures using larger key sizes.
Key management mechanisms negotiating the use of RSA signatures also
MUST include the encoding method during policy negotiation using the
Signature Encoding Algorithm SA Attribute.
A receiver must have the RSA public key in order to verify integrity
of the packet. When used with a group key management system (e.g.,
RFC 3547 [GDOI]), the public key SHOULD be sent as part of the key
download policy. If the group has multiple senders, the public key
of each sender SHOULD be sent as part of the key download policy.
Use of this transform to obtain data origin authentication for
pairwise SAs is NOT RECOMMENDED. In the case of pairwise SAs (such
as negotiated by the Internet Key Exchange [IKEV2]), data origin
authentication can be achieved with an HMAC transform. Because the
performance impact of an RSA signature is typically greater than an
HMAC, the value of using this transform for a pairwise connection is
limited.
Weis Standards Track [Page 6]
RFC 4359 RSA/SHA-1 Signatures within ESP and AH January 2006
6. Security Considerations
This document provides a method of authentication for ESP and AH
using digital signatures. This feature provides the following
protections:
o Message modification integrity. The digital signature allows the
receiver of the message to verify that it was exactly the same as
when the sender signed it.
o Host authentication. The asymmetric nature of the RSA public key
algorithm allows the sender to be uniquely verified, even when the
message is sent to a group.
Non-repudiation is not claimed as a property of this transform. At
times, the property of non-repudiation may be applied to digital
signatures on application-level objects (e.g., electronic mail).
However, this document describes a means of authenticating network-
level objects (i.e., IP packets), which are ephemeral and not
directly correlated to any application. Non-repudiation is not
applicable to network-level objects (i.e., IP packets).
A number of attacks are suggested by [RFC3552]. The following
sections describe the risks those attacks present when RSA signatures
are used for ESP and AH packet authentication.
SHA-1 has been scheduled to be phased out in 2010, due to the steady
advances in technology by which an adversary can double its computing
power in roughly eighteen months. Recent attacks on SHA-1 underscore
the importance of replacing SHA-1, but have not motivated replacing
it before that date [SHA-COMMENTS]. The use of this transform after
that date SHOULD be preceded by an analysis as to its continued
suitability.
6.1. Eavesdropping
This document does not address confidentiality. That function, if
desired, must be addressed by an ESP cipher that is used with the RSA
signatures authentication method. The RSA signature itself does not
need to be protected from an eavesdropper.
6.2. Replay
This document does not address replay attacks. That function, if
desired, is addressed through use of ESP and AH sequence numbers as
defined in [ESP] and [AH].
Weis Standards Track [Page 7]
RFC 4359 RSA/SHA-1 Signatures within ESP and AH January 2006
6.3. Message Insertion
This document directly addresses message insertion attacks. Inserted
messages will fail authentication and be dropped by the receiver.
6.4. Deletion
This document does not address deletion attacks. It is concerned
only with validating the legitimacy of messages that are not deleted.
6.5. Modification
This document directly addresses message modification attacks.
Modified messages will fail authentication and be dropped by the
receiver.
6.6. Man in the Middle
As long as a receiver is given the sender RSA public key in a trusted
manner (e.g., by a key management protocol), it will be able to
verify that the digital signature is correct. A man in the middle
will not be able to spoof the actual sender unless it acquires the
RSA private key through some means.
The RSA modulus size must be chosen carefully to ensure that the time
a man in the middle needs to determine the RSA private key through
cryptanalysis is longer than the amount of time that packets are
signed with that private key.
6.7. Denial of Service
According to IPsec processing rules, a receiver of an ESP and AH
packet begins by looking up the Security Association in the SA
database. If one is found, the ESP or AH sequence number in the
packet is verified. No further processing will be applied to packets
with an invalid sequence number.
An attacker that sends an ESP or AH packet matching a valid SA on the
system and also having a valid sequence number will cause the
receiver to perform the ESP or AH authentication step. Because the
process of verifying an RSA digital signature consumes relatively
large amounts of processing, many such packets could lead to a denial
of service (DoS) attack on the receiver.
If the message was sent to an IPv4 or IPv6 multicast group, all group
members that received the packet would be under attack
simultaneously.
Weis Standards Track [Page 8]
RFC 4359 RSA/SHA-1 Signatures within ESP and AH January 2006
This attack can be mitigated against most attackers by encapsulating
ESP or AH using an RSA signature for authentication within ESP or AH
using an HMAC transform for authentication. In this case, the HMAC
transform would be validated first, and as long as the attacker does
not possess the HMAC key no digital signatures would be evaluated on
the attacker packets. However, if the attacker does possess the HMAC
key (e.g., the attacker is a legitimate member of the group using the
SA), then the DoS attack cannot be mitigated.
7. IANA Considerations
An assigned number is required in the "IPSec Authentication
Algorithm" name space in the Internet Security Association and Key
Management Protocol (ISAKMP) registry [ISAKMP-REG]. The mnemonic
should be "SIG-RSA".
An assigned number is also required in the "IPSEC AH Transform
Identifiers" name space in the ISAKMP registry. Its mnemonic should
be "AH_RSA".
A new "IPSEC Security Association Attribute" is required in the
ISAKMP registry to pass the RSA modulus size. The attribute class
should be called "Authentication Key Length", and it should be a
Variable type.
A second "IPSEC Security Association Attribute" is required in the
ISAKMP registry to pass the RSA signature encoding type. The
attribute class should be called "Signature Encoding Algorithm", and
it should be a Basic type. The following rules apply to define the
values of the attribute:
Name Value
---- -----
Reserved 0
RSASSA-PKCS1-v1_5 1
RSASSA-PSS 2
Values 3-61439 are reserved to IANA. New values MUST be added due to
a Standards Action as defined in [RFC2434]. Values 61440-65535 are
for private use and may be allocated by implementations for their own
purposes.
Weis Standards Track [Page 9]
RFC 4359 RSA/SHA-1 Signatures within ESP and AH January 2006
8. Acknowledgements
Scott Fluhrer and David McGrew provided advice regarding applicable
key sizes. Scott Fluhrer also provided advice regarding key
lifetimes. Ian Jackson, Steve Kent, and Ran Canetti provided many
helpful comments. Sam Hartman, Russ Housley, and Lakshminth Dondeti
provided valuable guidance in the development of this document.
9. References
9.1. Normative References
[AH] Kent, S., "IP Authentication Header", RFC 4302,
December 2005.
[ESP] Kent, S., "IP Encapsulating Security Payload (ESP)",
RFC 4303, December 2005.
[ISAKMP-REG] http://www.iana.org/assignments/isakmp-registry
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Level", BCP 14, RFC 2119, March 1997.
[RFC3552] Rescorla, E. and B. Korver, "Guidelines for Writing
RFC Text on Security Considerations", BCP 72, RFC
3552, July 2003.
[RSA] Jonsson, J. and B. Kaliski, "Public-Key Cryptography
Standard (PKCS) #1: RSA Cryptography Specifications
Version 2.1", RFC 3447, February 2003.
[SHA] FIPS PUB 180-2: Specifications for the Secure Hash
Standard, August 2002. http://csrc.nist.gov/
publications/fips/fips180-2/fips180-2.pdf.
9.2. Informative References
[AES-GCM] Viega, J. and D. McGrew, "The Use of Galois/Counter
Mode (GCM) in IPsec Encapsulating Security Payload
(ESP)", RFC 4106, June 2005.
[GDOI] Baugher, M., Weis, B., Hardjono, T., and H. Harney,
"The Group Domain of Interpretation", RFC 3547,
December 2002.
[HMAC-SHA] Madson, C. and R. Glenn, "The Use of HMAC-SHA-1-96
within ESP and AH", RFC 2404, November 1998.
Weis Standards Track [Page 10]
RFC 4359 RSA/SHA-1 Signatures within ESP and AH January 2006
[IKEV2] Kaufman, C., "Internet Key Exchange (IKEv2) Protocol",
RFC 4306, December 2005.
[RFC2434] Narten, T. and H. Alvestrand, "Guidelines for Writing
an IANA Considerations Section in RFCs", BCP 26, RFC
2434, October 1998.
[RSA-TR] B. Kaliski, "TWIRL and RSA Key Size", RSA Laboratories
Technical Note, http://www.rsasecurity.com/rsalabs/
node.asp?id=2004, May 6, 2003.
[SHA-COMMENTS] NIST Brief Comments on Recent Cryptanalytic Attacks on
Secure Hashing Functions and the Continued Security
Provided by SHA-1, August, 2004.
http://csrc.nist.gov/hash_standards_comments.pdf.
[TWIRL] Shamir, A., and E. Tromer, "Factoring Large Numbers
with the TwIRL Device", Work in Progress, February 9,
2003.
Author's Address
Brian Weis
Cisco Systems
170 W. Tasman Drive,
San Jose, CA 95134-1706, USA
Phone: (408) 526-4796
EMail: bew@cisco.com
Weis Standards Track [Page 11]
RFC 4359 RSA/SHA-1 Signatures within ESP and AH January 2006
Full Copyright Statement
Copyright (C) The Internet Society (2006).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Weis Standards Track [Page 12]
ERRATA
