rfc5402
Independent Submission T. Harding, Ed.
Request for Comments: 5402 Axway
Category: Informational February 2010
ISSN: 2070-1721
Compressed Data within an Internet
Electronic Data Interchange (EDI) Message
Abstract
This document explains the rules and procedures for utilizing
compression (RFC 3274) within an Internet EDI (Electronic Data
Interchange) 'AS' message, as defined in RFCs 3335, 4130, and 4823.
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for informational purposes.
This is a contribution to the RFC Series, independently of any other
RFC stream. The RFC Editor has chosen to publish this document at
its discretion and makes no statement about its value for
implementation or deployment. Documents approved for publication by
the RFC Editor are not a candidate for any level of Internet
Standard; see Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc5402.
IESG Note
The content of this RFC was at one time considered by the IETF, and
therefore it may resemble a current IETF work in progress or a
published IETF work. This RFC is not a candidate for any level of
Internet Standard. Readers of this RFC should exercise caution in
evaluating its value for implementation and deployment.
Copyright Notice
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http:trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
Harding Informational [Page 1]
RFC 5402 Compressed Data in an Internet EDI Message February 2010
carefully, as they describe your rights and restrictions with respect
to this document.
1. Introduction
Historically, electronic messages produced by systems following the
guidelines as outlined in the IETF EDIINT Working Group
specifications AS1 [AS1], AS2 [AS2], and AS3 [AS3] did not have a way
to provide a standardized transport neutral mechanism for compressing
large payloads. However, with the development of RFC 3274,
"Compressed Data Content Type for Cryptographic Message Syntax
(CMS)", we now have a transport-neutral mechanism for compressing
large payloads.
A typical EDIINT 'AS' message is a multi-layered MIME message,
consisting of one or more of the following: payload layer, signature
layer, and/or encryption layer. When an 'AS' message is received, a
Message Integrity Check (MIC) value must be computed based upon
defined rules within the EDIINT 'AS' RFCs and must be returned to the
sender of the message via a Message Disposition Notification (MDN).
The addition of a new compression layer will require this document to
outline new procedures for building/layering 'AS' messages and
computing a MIC value that is returned in the MDN receipt.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
2. Compressed Data MIME Layer
The compressed-data CMS (Cryptographic Message Syntax) MIME entity as
described in [COMPRESSED-DATA] may encapsulate a MIME entity that
consists of either an unsigned or signed business document.
Implementers are to follow the appropriate specifications identified
in the "MIME Media Types" registry [MIME-TYPES] maintained by IANA
for the type of object being packaged. For example, to package an
XML object, the MIME media type of "application/xml" is used in the
Content-Type MIME header field and the specifications for enveloping
the object are contained in [XMLTYPES].
MIME entity example:
Content-type: application/xml; charset="utf-8"
<?xml version="1.0" encoding="UTF-8"?>
<!-- sample xml document -->
Harding Informational [Page 2]
RFC 5402 Compressed Data in an Internet EDI Message February 2010
The MIME entity will be compressed using [ZLIB] and placed inside a
CMS compressed-data object as outlined in [COMPRESSED-DATA]. The
compressed-data object will be MIME encapsulated according to details
outlined in [S/MIME3.1], RFC 3851, Section 3.5.
Example:
Content-Type: application/pkcs7-mime; smime-type=compressed-data;
name=smime.p7z
Content-Transfer-Encoding: base64
Content-Disposition: attachment; filename=smime.p7z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Note: Content-Transfer-Encoding of base64 would only be required if
the compressed-data MIME bodypart is transferred via a 7-bit protocol
like SMTP and is visible in the outer layer of the MIME message. If
the compressed-data MIME bodypart is placed inside of an encrypted
MIME bodypart, content-transfer-encoding would not be required on the
compressed-data MIME bodypart, but would be required on the encrypted
MIME bodypart.
3. Structure of an EDI MIME Compressed Message
When compressing a document that will be signed, the application MAY
compress the innermost MIME body before signing (see Sections 3.2 and
3.5), or it MAY compress the outer multipart/signed MIME body (see
Sections 3.3 and 3.6), but it MUST NOT do both within the same
document. The receiving application MUST support both methods of
compression when unpackaging an inbound document.
Note: The following sections (3.1 - 3.6) show the individual layers
of a properly formatted EDI MIME message with a compressed data
layer. Please refer to the appropriate RFCs for the proper
construction of the resulting MIME message. "application/xxxxxxx" is
used to indicate an application media subtype.
Harding Informational [Page 3]
RFC 5402 Compressed Data in an Internet EDI Message February 2010
3.1. No Encryption, No Signature
-RFC5322/2045
-[COMPRESSED-DATA](application/pkcs7-mime)
-[MIME-TYPES](application/xxxxxxx)(compressed)
This section shows the layers of an unsigned, unencrypted compressed
message. The first line indicates that the MIME message conforms to
[RFC5322] and [RFC2045] with a Content-Type of
application/pkcs7-mime. Within the pkcs7-mime entity is a compressed
MIME entity containing the electronic business document.
3.2. No Encryption, Signature
-RFC5322/2045
-[RFC1847] (multipart/signed)
-[COMPRESSED-DATA](application/pkcs7-mime)
-[MIME-TYPES](application/xxxxxxx)(compressed)
-RFC3851 (application/pkcs7-signature)
This section shows the layers of a signed, unencrypted compressed
message where the payload is compressed before being signed.
3.3. No Encryption, Signature
-RFC5322/2045
-[COMPRESSED-DATA](application/pkcs7-mime)
-[RFC1847] (multipart/signed)(compressed)
-[MIME-TYPES](application/xxxxxxx)(compressed)
-RFC3851 (application/pkcs7-signature)(compressed)
This section shows the layers of a signed, unencrypted compressed
message where a signed payload is compressed.
3.4. Encryption, No Signature
-RFC5322/2045
-RFC3851 (application/pkcs7-mime)
-[COMPRESSED-DATA](application/pkcs7-mime) (encrypted)
-[MIME-TYPES](application/xxxxxxx)(compressed)(encrypted)
This section shows the layers of an unsigned, encrypted compressed
message where the payload is compressed before it is encrypted.
Harding Informational [Page 4]
RFC 5402 Compressed Data in an Internet EDI Message February 2010
3.5. Encryption, Signature
-RFC5322/2045
-RFC3851 (application/pkcs7-mime)
-[RFC1847] (multipart/signed) (encrypted)
-[COMPRESSED-DATA](application/pkcs7-mime) (encrypted)
-[MIME-TYPES](application/xxxxxxx) (compressed)(encrypted)
-RFC3851 (application/pkcs7-signature) (encrypted)
This section shows the layers of a signed, encrypted compressed
message where the payload is compressed before being signed and
encrypted.
3.6. Encryption, Signature
-RFC5322/2045
-RFC3851 (application/pkcs7-mime)
-[COMPRESSED-DATA](application/pkcs7-mime) (encrypted)
-[RFC1847] (multipart/signed) (compressed)(encrypted)
-[MIME-TYPES](application/xxxxxxx) (compressed)(encrypted)
-RFC3851 (application/pkcs7-signature)(compressed)(encrypted)
This section shows the layers of a signed, encrypted compressed
message where the payload is signed before being compressed and
encrypted.
4. MIC Calculations for Compressed Messages Requesting Signed Receipts
4.1. MIC Calculation for Signed Message
For any signed message, the MIC to be returned is calculated over the
same data that was signed in the original message as per [AS1]. The
signed content will be a MIME bodypart that contains either
compressed or uncompressed data.
4.2. MIC Calculation for Encrypted, Unsigned Message
For encrypted, unsigned messages, the MIC to be returned is
calculated over the uncompressed data content including all MIME
header fields and any applied Content-Transfer-Encoding.
4.3. MIC Calculation for Unencrypted, Unsigned Message
For unsigned, unencrypted messages, the MIC is calculated over the
uncompressed data content including all MIME header fields and any
applied Content-Transfer-Encoding.
Harding Informational [Page 5]
RFC 5402 Compressed Data in an Internet EDI Message February 2010
5. Error Disposition Modifier
For a received message where a receipt has been requested and
decompression fails, the following disposition modifier will be
returned in the signed MDN.
"Error: decompression-failed" - the receiver could not decompress
the message
6. EDIINT Version Header Field
Any application that supports the compression methods outlined within
this document MUST use a version identifier value of "1.1" or greater
within the AS2 or AS3 Version header field as describe in [AS2] and
[AS3].
7. Compression Formats
Implementations MUST support ZLIB [ZLIB], which utilizes DEFLATE
[DEFLATE].
8. Security Considerations
This document is not concerned with security, except for any security
concerns mentioned in the referenced RFCs.
9. Normative References
[AS1] Harding, T., Drummond, R., and C. Shih, "MIME-based
Secure Peer-to-Peer Business Data Interchange over the
Internet", RFC 3335, September 2002.
[AS2] Moberg, D. and R. Drummond, "MIME-Based Secure Peer-to-
Peer Business Data Interchange Using HTTP,
Applicability Statement 2 (AS2)", RFC 4130, July 2005.
[AS3] Harding, T. and R. Scott, "FTP Transport for Secure
Peer-to-Peer Business Data Interchange over the
Internet", RFC 4823, April 2007.
[ZLIB] Deutsch, P. and J-L. Gailly, "ZLIB Compressed Data
Format Specification version 3.3", RFC 1950, May 1996.
[DEFLATE] Deutsch, P., "DEFLATE Compressed Data Format
Specification version 1.3", RFC 1951, May 1996.
[MIME-TYPES] IANA, "MIME Media Types" registry, available from
http://www.iana.org.
Harding Informational [Page 6]
RFC 5402 Compressed Data in an Internet EDI Message February 2010
[RFC1847] Galvin, J., Murphy, S., Crocker, S., and N. Freed,
"Security Multiparts for MIME: Multipart/Signed and
Multipart/Encrypted", RFC 1847, October 1995.
[RFC2045] Freed, N. and N. Borenstein, "Multipurpose Internet
Mail Extensions (MIME) Part One: Format of Internet
Message Bodies", RFC 2045, November 1996.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC5322] Resnick, P., Ed., "Internet Message Format", RFC 5322,
October 2008.
[S/MIME3.1] Ramsdell, B. and S. Turner, "Secure/Multipurpose
Internet Mail Extensions (S/MIME) Version 3.2 Message
Specification", RFC 5751, January 2010.
[XMLTYPES] Murata, M., St. Laurent, S., and D. Kohn, "XML Media
Types", RFC 3023, January 2001.
[COMPRESSED-DATA]
Gutmann, P., "Compressed Data Content Type for
Cryptographic Message Syntax (CMS)", RFC 3274, June
2002.
10. Acknowledgments
A number of the members of the EDIINT Working Group have also worked
very hard and contributed to this document. The following people have
made direct contributions to this document:
David Fischer, Dale Moberg, Robert Asis, and everyone involved in the
AS1, AS2 Interop testing during 2002.
Author's Address
Terry Harding
Axway
Scottsdale, Arizona
USA
EMail: tharding@us.axway.com
Harding Informational [Page 7]
ERRATA
