rfc6094
Internet Engineering Task Force (IETF) M. Bhatia
Request for Comments: 6094 Alcatel-Lucent
Category: Informational V. Manral
ISSN: 2070-1721 IP Infusion
February 2011
Summary of Cryptographic Authentication Algorithm Implementation
Requirements for Routing Protocols
Abstract
The routing protocols Open Shortest Path First version 2 (OSPFv2),
Intermediate System to Intermediate System (IS-IS), and Routing
Information Protocol (RIP) currently define cleartext and MD5
(Message Digest 5) methods for authenticating protocol packets.
Recently, effort has been made to add support for the SHA (Secure
Hash Algorithm) family of hash functions for the purpose of
authenticating routing protocol packets for RIP, IS-IS, and OSPF.
To encourage interoperability between disparate implementations, it
is imperative that we specify the expected minimal set of algorithms,
thereby ensuring that there is at least one algorithm that all
implementations will have in common.
Similarly, RIP for IPv6 (RIPng) and OSPFv3 support IPsec algorithms
for authenticating their protocol packets.
This document examines the current set of available algorithms, with
interoperability and effective cryptographic authentication
protection being the principal considerations. Cryptographic
authentication of these routing protocols requires the availability
of the same algorithms in disparate implementations. It is desirable
that newly specified algorithms should be implemented and available
in routing protocol implementations because they may be promoted to
requirements at some future time.
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for informational purposes.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Not all documents
approved by the IESG are a candidate for any level of Internet
Standard; see Section 2 of RFC 5741.
Bhatia & Manral Informational [Page 1]
RFC 6094 Crypto Reqs for Routing Protocols February 2011
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc6094.
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction ....................................................3
2. Intermediate System to Intermediate System (IS-IS) ..............4
2.1. Authentication Scheme Selection ............................4
2.2. Authentication Algorithm Selection .........................5
3. Open Shortest Path First Version 2 (OSPFv2) .....................5
3.1. Authentication Scheme Selection ............................6
3.2. Authentication Algorithm Selection .........................6
4. Open Shortest Path First Version 3 (OSPFv3) .....................7
5. Routing Information Protocol Version 2 (RIPv2) ..................7
5.1. Authentication Scheme Selection ............................7
5.2. Authentication Algorithm Selection .........................8
6. Routing Information Protocol for IPv6 (RIPng) ...................8
7. Security Considerations .........................................9
8. Acknowledgements ................................................9
9. References .....................................................10
9.1. Normative References ......................................10
9.2. Informative References ....................................10
Bhatia & Manral Informational [Page 2]
RFC 6094 Crypto Reqs for Routing Protocols February 2011
1. Introduction
Most routing protocols include three different types of
authentication schemes: Null authentication, cleartext password, and
cryptographic authentication. Null authentication is equivalent to
having no authentication scheme at all.
In a cleartext scheme, also known as a "simple password" scheme, the
password is exchanged completely unprotected, and anyone with
physical access to the network can learn the password and compromise
the integrity of the routing domain. The simple password scheme
protects against accidental establishment of routing sessions in a
given domain, but beyond that it offers no additional protection.
In a cryptographic authentication scheme, routers share a secret key
that is used to generate a message authentication code for each of
the protocol packets. Today, routing protocols that implement
message authentication codes often use a Keyed-MD5 [RFC1321] digest.
The recent escalating series of attacks on MD5 raise concerns about
its remaining useful lifetime.
These attacks may not necessarily result in direct vulnerabilities
for Keyed-MD5 digests as message authentication codes because the
colliding message may not correspond to a syntactically correct
protocol packet. The known collision, pre-image, and second
pre-image attacks [RFC4270] on MD5 may not increase the effectiveness
of the key recovery attacks on HMAC-MD5. Regardless, there is a need
felt to deprecate MD5 [RFC1321] as the basis for the Hashed Message
Authentication Code (HMAC) algorithm in favor of stronger digest
algorithms.
In light of these considerations, there are proposals to replace
HMAC-MD5 with keyed HMAC-SHA [SHS] digests where HMAC-MD5 is
currently mandated in RIPv2 [RFC2453] IS-IS [ISO] [RFC1195], and
Keyed-MD5 in OSPFv2 [RFC2328].
OSPFv3 [RFC5340] and RIPng [RFC2080] rely on the IPv6 Authentication
Header (AH) [RFC4302] and IPv6 Encapsulating Security Payload (ESP)
[RFC4303] in order to provide integrity, authentication, and/or
confidentiality.
However, the nature of cryptography is that algorithmic improvement
is an ongoing process, as is the exploration and refinement of attack
vectors. An algorithm believed to be strong today may be
demonstrated to be weak tomorrow. Given this, the choice of
preferred algorithm should favor the minimization of the likelihood
of it being compromised quickly.
Bhatia & Manral Informational [Page 3]
RFC 6094 Crypto Reqs for Routing Protocols February 2011
It should be recognized that preferred algorithm(s) will change over
time to adapt to the evolving threats. At any particular time, the
mandatory-to-implement algorithm(s) might not be specified in the
base protocol specification. As protocols are extended, the
preference for presently stronger algorithms presents a problem
regarding the question of interoperability of existing and future
implementations with respect to standards, and also regarding
operational preference for the configuration as deployed.
It is expected that an implementation should support the changing of
security (authentication) keys. Changing the symmetric key used in
any HMAC algorithm on a periodic basis is good security practice.
Operators need to plan for this.
Implementations can support in-service key change so that no control
packets are lost. During an in-service/in-band key change, more than
one key can be active for receiving packets for a session. Some
protocols support a key identifier that allows the two peers of a
session to have multiple keys simultaneously for a session.
However, these protocols currently manage keys manually (i.e., via
operator intervention) or dynamically based on some timer or security
protocol.
2. Intermediate System to Intermediate System (IS-IS)
The IS-IS specification allows for authentication of its Protocol
Data Units (PDUs) via the authentication TLV (TLV 10) in the PDU.
The base specification [ISO] had provisions only for cleartext
passwords. [RFC5304] extends the authentication capabilities by
providing cryptographic authentication for IS-IS PDUs. It mandates
support for HMAC-MD5.
[RFC5310] adds support for the use of any cryptographic hash function
for authenticating IS-IS PDUs. In addition to this, [RFC5310] also
details how IS-IS can use the HMAC construct along with the Secure
Hash Algorithm (SHA) family of cryptographic hash functions to secure
IS-IS PDUs.
2.1. Authentication Scheme Selection
In order for IS-IS implementations to securely interoperate, they
must support one or more authentication schemes in common. This
section specifies the preference for standards-conformant IS-IS
implementations that use accepted authentication schemes.
The earliest interoperability requirement for authentication as
stated by [ISO] [RFC1195] required all implementations to support a
Bhatia & Manral Informational [Page 4]
RFC 6094 Crypto Reqs for Routing Protocols February 2011
cleartext password. This authentication scheme's utility is limited
to precluding the accidental introduction of a new IS into a
broadcast domain. Operators should not use this scheme, as it
provides no protection against an attacker with access to the
broadcast domain: anyone can determine the secret password through
inspection of the PDU. This mechanism does not provide any
significant level of security and should be avoided.
[RFC5304] defined the cryptographic authentication scheme for IS-IS.
HMAC-MD5 was the only algorithm specified; hence, it is mandated.
[RFC5310] defined a generic cryptographic scheme and added support
for additional algorithms. Implementations should support [RFC5310],
as it defines the generic cryptographic authentication scheme.
2.2. Authentication Algorithm Selection
For IS-IS implementations to securely interoperate, they must have
support for one or more authentication algorithms in common.
This section details the authentication algorithm requirements for
standards-conformant IS-IS implementations.
The following are the available options for authentication
algorithms:
o [RFC5304] mandates the use of HMAC-MD5.
o [RFC5310] does not require a particular algorithm but instead
supports any digest algorithm (i.e., cryptographic hash
functions).
As noted earlier, there is a desire to deprecate MD5. IS-IS
implementations will likely migrate to an authentication scheme
supported by [RFC5310], because it is algorithm agnostic. Possible
digest algorithms include SHA-1, SHA-224, SHA-256, SHA-384, and
SHA-512. Picking at least one mandatory-to-implement algorithm is
imperative to ensuring interoperability.
3. Open Shortest Path First Version 2 (OSPFv2)
[RFC2328] includes three different types of authentication schemes:
Null authentication, cleartext password (defined as "simple password"
in [RFC2328]), and cryptographic authentication. Null authentication
is semantically equivalent to no authentication.
In the cryptographic authentication scheme, the OSPFv2 routers on a
common network/subnet are configured with a shared secret that is
used to generate a Keyed-MD5 digest for each packet. A monotonically
Bhatia & Manral Informational [Page 5]
RFC 6094 Crypto Reqs for Routing Protocols February 2011
increasing sequence number scheme is used to protect against replay
attacks.
[RFC5709] adds support for the use of the SHA family of hash
algorithms for authentication of OSPFv2 packets.
3.1. Authentication Scheme Selection
For OSPF implementations to securely interoperate, they must have one
or more authentication schemes in common.
While all implementations will have Null authentication since it's
mandated by [RFC2328], its use is not appropriate in any context
where the operator wishes to authenticate OSPFv2 packets in their
network.
While all implementations will also support a cleartext password
since it's mandated by [RFC2328], its use is only appropriate when
the operator wants to preclude the accidental introduction of a
router into the domain. This scheme is patently not useful when an
operator wants to authenticate the OSPFv2 packets.
Cryptographic authentication is a mandatory scheme defined in
[RFC2328], and all conformant implementations must support this.
3.2. Authentication Algorithm Selection
For OSPFv2 implementations to securely interoperate, they must
support one or more cryptographic authentication algorithms in
common.
The following are the available options for authentication
algorithms:
o [RFC2328] specifies the use of Keyed-MD5.
o [RFC5709] specifies the use of HMAC-SHA-1, HMAC-SHA-256,
HMAC-SHA-384, and HMAC-SHA-512, and also mandates support for
HMAC-SHA-256 (HMAC-SHA-1 is optional).
As noted earlier, there is a desire to deprecate MD5. Some
alternatives for MD5 are listed in [RFC5709].
Possible digest algorithms include SHA-1, SHA-256, SHA-384, and
SHA-512. Picking one mandatory-to-implement algorithm is imperative
to ensuring interoperability.
Bhatia & Manral Informational [Page 6]
RFC 6094 Crypto Reqs for Routing Protocols February 2011
4. Open Shortest Path First Version 3 (OSPFv3)
OSPFv3 [RFC5340] relies on the IPv6 Authentication Header (AH)
[RFC4302] and IPv6 Encapsulating Security Payload (ESP) [RFC4303] in
order to provide integrity, authentication, and/or confidentiality.
[RFC4552] mandates the use of ESP for authenticating OSPFv3 packets.
The implementations could also provide support for using AH to
protect these packets.
The algorithm requirements for AH and ESP are described in [RFC4835]
as follows:
o [RFC2404] mandates HMAC-SHA-1-96.
o [RFC3566] indicates AES-XCBC-MAC-96 as a "should", but it's likely
that this will be mandated at some future time.
5. Routing Information Protocol Version 2 (RIPv2)
RIPv2, originally specified in [RFC1388] and then in [RFC1723], has
been updated and published as STD 56, [RFC2453]. If the Address
Family Identifier of the first (and only the first) entry in the
RIPv2 message is 0xFFFF, then the remainder of the entry contains the
authentication information. The [RFC2453] version of the protocol
provides for authenticating packets using a cleartext password
(defined as "simple password" in [RFC2453]) not more than 16 octets
in length.
[RFC2082] added support for Keyed-MD5 authentication, where a digest
is appended to the end of the RIP packet. [RFC4822] obsoleted
[RFC2082] and added the SHA family of hash algorithms to the list of
cryptographic authentications that can be used to protect RIPv2,
whereas [RFC2082] previously specified only the use of Keyed-MD5.
5.1. Authentication Scheme Selection
For RIPv2 implementations to securely interoperate, they must support
one or more authentication schemes in common.
While all implementations will support a cleartext password since
it's mandated by [RFC2453], its use is only appropriate when the
operator wants to preclude the accidental introduction of a router
into the domain. This scheme is patently not useful when an operator
wants to authenticate the RIPv2 packets.
Bhatia & Manral Informational [Page 7]
RFC 6094 Crypto Reqs for Routing Protocols February 2011
[RFC2082] mandates the use of an authentication scheme that uses
Keyed-MD5. However, [RFC2082] has been obsoleted by [RFC4822].
Compliant implementations must provide support for an authentication
scheme that uses Keyed-MD5 but should recognize that this is
superseded by cryptographic authentication as defined in [RFC4822].
Implementations should provide support for [RFC4822], as it specifies
the RIPv2 cryptographic authentication schemes.
5.2. Authentication Algorithm Selection
For RIPv2 implementations to securely interoperate, they must support
one or more authentication algorithms in common.
The following are the available options for authentication
algorithms:
o [RFC2082] specifies the use of Keyed-MD5.
o [RFC4822] specifies the use of Keyed-MD5, HMAC-SHA-1,
HMAC-SHA-256, HMAC-SHA-384, and HMAC-SHA-512.
As noted earlier, there is a desire to deprecate MD5. Some
alternatives for MD5 are listed in [RFC4822]. Possible digest
algorithms include SHA-1, SHA-256, SHA-384, and SHA-512. Picking one
mandatory-to-implement algorithm is imperative to ensuring
interoperability.
6. Routing Information Protocol for IPv6 (RIPng)
RIPng [RFC2080] relies on the IPv6 Authentication Header (AH)
[RFC4302] and IPv6 Encapsulating Security Payload (ESP) [RFC4303] in
order to provide integrity, authentication, and/or confidentiality.
The algorithm requirements for AH and ESP are described in [RFC4835]
as follows:
o [RFC2404] mandates HMAC-SHA-1-96.
o [RFC3566] indicates AES-XCBC-MAC-96 as a "should", but it's likely
that this will be mandated at some future time.
Bhatia & Manral Informational [Page 8]
RFC 6094 Crypto Reqs for Routing Protocols February 2011
7. Security Considerations
The cryptographic mechanisms referenced in this document provide only
authentication algorithms. These algorithms do not provide
confidentiality. Encrypting the content of the packet and thereby
providing confidentiality is not considered in the definition of the
routing protocols.
The cryptographic strength of the HMAC depends upon the cryptographic
strength of the underlying hash function and on the size and quality
of the key. The feasibility of attacking the integrity of routing
protocol messages protected by keyed digests may be significantly
more limited than that of other data; however, preference for one
family of algorithms over another may also change independently of
the perceived risk to a particular protocol.
To ensure greater security, the keys used should be changed
periodically, and implementations must be able to store and use more
than one key at the same time. Operational experience suggests that
the lack of periodic rekeying is a source of significant exposure and
that the lifespan of shared keys in the network is frequently
measured in years.
While simple password schemes are well represented in the document
series and in conformant implementations of the protocols, the
inability to offer either integrity or identity protection are
sufficient reason to strongly discourage their use.
This document concerns itself with the selection of cryptographic
algorithms for use in the authentication of routing protocol packets
being exchanged between adjacent routing processes. The
cryptographic algorithms identified in this document are not known to
be broken at the current time, and ongoing cryptographic research so
far leads us to believe that they will likely remain secure in the
foreseeable future. We expect that new revisions of this document
will be issued in the future to reflect current thinking on the
algorithms that various routing protocols should employ to ensure
interoperability between disparate implementations.
8. Acknowledgements
We would like to thank Joel Jaeggli, Sean Turner, and Adrian Farrel
for their comments and feedback on this document, which resulted in
significant improvement of the same.
Bhatia & Manral Informational [Page 9]
RFC 6094 Crypto Reqs for Routing Protocols February 2011
9. References
9.1. Normative References
[ISO] "Intermediate system to Intermediate system routing
information exchange protocol for use in conjunction with
the protocol for providing the connectionless-mode
network service", ISO/IEC 10589:1992 (ISO 8473).
[RFC1195] Callon, R., "Use of OSI IS-IS for routing in TCP/IP and
dual environments", RFC 1195, December 1990.
[RFC2080] Malkin, G. and R. Minnear, "RIPng for IPv6", RFC 2080,
January 1997.
[RFC2328] Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998.
[RFC2453] Malkin, G., "RIP Version 2", STD 56, RFC 2453,
November 1998.
[RFC4822] Atkinson, R. and M. Fanto, "RIPv2 Cryptographic
Authentication", RFC 4822, February 2007.
[RFC4835] Manral, V., "Cryptographic Algorithm Implementation
Requirements for Encapsulating Security Payload (ESP) and
Authentication Header (AH)", RFC 4835, April 2007.
[RFC5304] Li, T. and R. Atkinson, "IS-IS Cryptographic
Authentication", RFC 5304, October 2008.
[RFC5310] Bhatia, M., Manral, V., Li, T., Atkinson, R., White, R.,
and M. Fanto, "IS-IS Generic Cryptographic
Authentication", RFC 5310, February 2009.
[RFC5340] Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF
for IPv6", RFC 5340, July 2008.
[RFC5709] Bhatia, M., Manral, V., Fanto, M., White, R., Barnes, M.,
Li, T., and R. Atkinson, "OSPFv2 HMAC-SHA Cryptographic
Authentication", RFC 5709, October 2009.
9.2. Informative References
[RFC1321] Rivest, R., "The MD5 Message-Digest Algorithm", RFC 1321,
April 1992.
[RFC1388] Malkin, G., "RIP Version 2 Carrying Additional
Information", RFC 1388, January 1993.
Bhatia & Manral Informational [Page 10]
RFC 6094 Crypto Reqs for Routing Protocols February 2011
[RFC1723] Malkin, G., "RIP Version 2 - Carrying Additional
Information", RFC 1723, November 1994.
[RFC2082] Baker, F. and R. Atkinson, "RIP-2 MD5 Authentication",
RFC 2082, January 1997.
[RFC2404] Madson, C. and R. Glenn, "The Use of HMAC-SHA-1-96 within
ESP and AH", RFC 2404, November 1998.
[RFC3566] Frankel, S. and H. Herbert, "The AES-XCBC-MAC-96
Algorithm and Its Use With IPsec", RFC 3566,
September 2003.
[RFC4270] Hoffman, P. and B. Schneier, "Attacks on Cryptographic
Hashes in Internet Protocols", RFC 4270, November 2005.
[RFC4302] Kent, S., "IP Authentication Header", RFC 4302,
December 2005.
[RFC4303] Kent, S., "IP Encapsulating Security Payload (ESP)",
RFC 4303, December 2005.
[RFC4552] Gupta, M. and N. Melam, "Authentication/Confidentiality
for OSPFv3", RFC 4552, June 2006.
[SHS] "Secure Hash Standard (SHS)", National Institute of
Standards and Technology (NIST) FIPS Publication 180-3,
October 2008.
Authors' Addresses
Manav Bhatia
Alcatel-Lucent
Bangalore
India
EMail: manav.bhatia@alcatel-lucent.com
Vishwas Manral
IP Infusion
1188 E. Arques Ave.
Sunnyvale, CA 94089
USA
Phone: 408-400-1900
EMail: vishwas@ipinfusion.com
Bhatia & Manral Informational [Page 11]
ERRATA
