rfc7689
Internet Engineering Task Force (IETF) G. Bernstein, Ed.
Request for Comments: 7689 Grotto Networking
Category: Standards Track S. Xu
ISSN: 2070-1721 NICT
Y. Lee, Ed.
Huawei
G. Martinelli
Cisco
H. Harai
NICT
November 2015
Signaling Extensions for Wavelength Switched Optical Networks
Abstract
This document provides extensions to Generalized Multiprotocol Label
Switching (GMPLS) signaling for control of Wavelength Switched
Optical Networks (WSONs). Such extensions are applicable in WSONs
under a number of conditions including: (a) when optional processing,
such as regeneration, must be configured to occur at specific nodes
along a path, (b) where equipment must be configured to accept an
optical signal with specific attributes, or (c) where equipment must
be configured to output an optical signal with specific attributes.
This document provides mechanisms to support distributed wavelength
assignment with a choice of distributed wavelength assignment
algorithms.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc7689.
Bernstein, et al. Standards Track [Page 1]
RFC 7689 WSON Signaling Extensions November 2015
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction ....................................................3
2. Terminology .....................................................3
2.1. Conventions Used in This Document ..........................4
3. Requirements for WSON Signaling .................................4
3.1. WSON Signal Characterization ...............................4
3.2. Per-Node Processing Configuration ..........................5
3.3. Bidirectional WSON LSPs ....................................5
3.4. Distributed Wavelength Assignment Selection Method .........6
3.5. Optical Impairments ........................................6
4. WSON Signal Traffic Parameters, Attributes, and Processing ......6
4.1. Traffic Parameters for Optical Tributary Signals ...........7
4.2. WSON Processing Hop Attribute TLV ..........................7
4.2.1. ResourceBlockInfo Sub-TLV ...........................8
4.2.2. WavelengthSelection Sub-TLV .........................9
5. Security Considerations ........................................11
6. IANA Considerations ............................................11
7. References .....................................................13
7.1. Normative References ......................................13
7.2. Informative References ....................................14
Acknowledgments ...................................................15
Contributors ......................................................15
Author's Addresses ................................................16
Bernstein, et al. Standards Track [Page 2]
RFC 7689 WSON Signaling Extensions November 2015
1. Introduction
This document provides extensions to Generalized Multiprotocol Label
Switching (GMPLS) signaling for control of Wavelength Switched
Optical Networks (WSONs). Fundamental extensions are given to permit
simultaneous bidirectional wavelength assignment, while more advanced
extensions are given to support the networks described in [RFC6163],
which feature connections requiring configuration of input, output,
and general signal processing capabilities at a node along a Label
Switched Path (LSP).
These extensions build on previous work for the control of lambda and
G.709-based networks.
Related documents are [RFC7446] that provides a high-level
information model and [RFC7581] that provides common encodings that
can be applicable to other protocol extensions such as routing.
2. Terminology
CWDM: Coarse Wavelength Division Multiplexing.
DWDM: Dense Wavelength Division Multiplexing.
ROADM: Reconfigurable Optical Add/Drop Multiplexer. A reduced port
count wavelength selective switching element featuring ingress and
egress line side ports as well as add/drop side ports.
RWA: Routing and Wavelength Assignment.
Wavelength Conversion/Converters: The process of converting
information bearing optical signal centered at a given frequency
(wavelength) to one with "equivalent" content centered at a
different wavelength. Wavelength conversion can be implemented
via an optical-electronic-optical (OEO) process or via a strictly
optical process.
WDM: Wavelength Division Multiplexing.
Wavelength Switched Optical Networks (WSONs): WDM-based optical
networks in which switching is performed selectively based on the
frequency of an optical signal.
AWG: Arrayed Waveguide Grating.
OXC: Optical Cross-Connect.
Bernstein, et al. Standards Track [Page 3]
RFC 7689 WSON Signaling Extensions November 2015
Optical Transmitter: A device that has both a laser, tuned on a
certain wavelength, and electronic components that convert
electronic signals into optical signals.
Optical Receiver: A device that has both optical and electronic
components. It detects optical signals and converts optical
signals into electronic signals.
Optical Transponder: A device that has both an optical transmitter
and an optical receiver.
Optical End Node: The end of a wavelength (optical lambdas) lightpath
in the data plane. It may be equipped with some
optical/electronic devices such as wavelength
multiplexers/demultiplexer (e.g., AWG), optical transponder, etc.,
which are employed to transmit/terminate the optical signals for
data transmission.
FEC: Forward Error Correction. FEC is a digital signal processing
technique used to enhance data reliability. It does this by
introducing redundant data, called error correcting code, prior to
data transmission or storage. FEC provides the receiver with the
ability to correct errors without a reverse channel to request the
retransmission of data.
3R Regeneration: The process of amplifying (correcting loss),
reshaping (correcting noise and dispersion), retiming
(synchronizing with the network clock), and retransmitting an
optical signal.
2.1. Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
3. Requirements for WSON Signaling
The following requirements for GMPLS-based WSON signaling are in
addition to the functionality already provided by existing GMPLS
signaling mechanisms.
3.1. WSON Signal Characterization
WSON signaling needs to convey sufficient information characterizing
the signal to allow systems along the path to determine compatibility
and perform any required local configuration. Examples of such
systems include intermediate nodes (ROADMs, OXCs, wavelength
Bernstein, et al. Standards Track [Page 4]
RFC 7689 WSON Signaling Extensions November 2015
converters, regenerators, OEO switches, etc.), links (WDM systems),
and end systems (detectors, demodulators, etc.). The details of any
local configuration processes are outside the scope of this document.
From [RFC6163], we have the following list of WSON signal
characteristics:
1. Optical tributary signal class (modulation format).
2. FEC: whether forward error correction is used in the digital
stream and what type of error correcting code is used
3. Center frequency (wavelength)
4. Bit rate
5. G-PID: General Protocol Identifier for the information format
The first three items on this list can change as a WSON signal
traverses a network with regenerators, OEO switches, or wavelength
converters. These parameters are summarized in the Optical Interface
Class as defined in [RFC7446], and the assumption is that a class
always includes signal compatibility information. An ability to
control wavelength conversion already exists in GMPLS signaling along
with the ability to share client signal type information (G-PID). In
addition, bit rate is a standard GMPLS signaling traffic parameter.
It is referred to as bandwidth encoding in [RFC3471].
3.2. Per-Node Processing Configuration
In addition to configuring a node along an LSP to input or output a
signal with specific attributes, we may need to signal the node to
perform specific processing, such as 3R regeneration, on the signal
at a particular node. [RFC6163] discussed three types of processing:
(A) Regeneration (possibly different types)
(B) Fault and Performance Monitoring
(C) Attribute Conversion
The extensions here provide for the configuration of these types of
processing at nodes along an LSP.
3.3. Bidirectional WSON LSPs
WSON signaling can support LSP setup consistent with the wavelength
continuity constraint for bidirectional connections. The following
cases need to be supported separately:
(a) Where the same wavelength is used for both upstream and
downstream directions
Bernstein, et al. Standards Track [Page 5]
RFC 7689 WSON Signaling Extensions November 2015
(b) Where different wavelengths are used for both upstream and
downstream directions.
This document will review existing GMPLS bidirectional solutions
according to WSON case.
3.4. Distributed Wavelength Assignment Selection Method
WSON signaling can support the selection of a specific distributed
wavelength assignment method.
This method is beneficial in cases of equipment failure, etc., where
fast provisioning used in quick recovery is critical to protect
carriers/users against system loss. This requires efficient
signaling that supports distributed wavelength assignment, in
particular, when the wavelength assignment capability is not
available.
As discussed in [RFC6163], different computational approaches for
wavelength assignment are available. One method is the use of
distributed wavelength assignment. This feature would allow the
specification of a particular approach when more than one is
implemented in the systems along the path.
3.5. Optical Impairments
This document does not address signaling information related to
optical impairments.
4. WSON Signal Traffic Parameters, Attributes, and Processing
As discussed in [RFC6163], single-channel optical signals used in
WSONs are called "optical tributary signals" and come in a number of
classes characterized by modulation format and bit rate. Although
WSONs are fairly transparent to the signals they carry, to ensure
compatibility amongst various networks devices and end systems, it
can be important to include key lightpath characteristics as traffic
parameters in signaling [RFC6163].
LSPs signaled through extensions provided in this document MUST apply
the following signaling parameters:
o Switching Capability = WSON-LSC [RFC7688]
o Encoding Type = Lambda [RFC3471]
o Label Format = as defined in [RFC6205]
[RFC6205] defines the label format as applicable to LSC capable
devices.
Bernstein, et al. Standards Track [Page 6]
RFC 7689 WSON Signaling Extensions November 2015
4.1. Traffic Parameters for Optical Tributary Signals
In [RFC3471] we see that the G-PID (client signal type) and bit rate
(byte rate) of the signals are defined as parameters, and in
[RFC3473] they are conveyed in the Generalized Label Request object
and the RSVP SENDER_TSPEC/FLOWSPEC objects, respectively.
4.2. WSON Processing Hop Attribute TLV
Section 3.1 provides requirements to signal to a node along an LSP
what type of processing to perform on an optical signal and how to
configure itself to accept or transmit an optical signal with
particular attributes.
To target a specific node, this section defines a WSON Processing Hop
Attribute TLV. This TLV is encoded as an attributes TLV; see
[RFC5420]. The TLV is carried in the ERO and RRO Hop Attributes
subobjects and processed according to the procedures defined in
[RFC7570]. The type value of the WSON Processing Hop Attribute TLV
is 4 as assigned by IANA.
The WSON Processing Hop Attribute TLV carries one or more sub-TLVs
with the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
// Value //
| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
The identifier of the sub-TLV.
Length
Indicates the total length of the sub-TLV in octets. That is, the
combined length of the Type, Length, and Value fields, i.e., two
plus the length of the Value field in octets.
Value
Zero or more octets of data carried in the sub-TLV.
Bernstein, et al. Standards Track [Page 7]
RFC 7689 WSON Signaling Extensions November 2015
Padding
Variable
The entire sub-TLV MUST be padded with zeros to ensure four-octet
alignment of the sub-TLV.
Sub-TLV ordering is significant and MUST be preserved. Error
processing follows [RFC7570].
The following sub-TLV types are defined in this document:
Sub-TLV Name Type Length
--------------------------------------------------------------
ResourceBlockInfo 1 variable
WavelengthSelection 2 8 octets (2-octet padding)
The TLV can be represented in Reduced Backus-Naur Form (RBNF)
[RFC5511] syntax as:
<WSON Processing Hop Attribute> ::= <ResourceBlockInfo>
[<ResourceBlockInfo>] [<WavelengthSelection>]
4.2.1. ResourceBlockInfo Sub-TLV
The format of the ResourceBlockInfo sub-TLV value field is defined in
Section 4 of [RFC7581]. It is a list of available Optical Interface
Classes and processing capabilities.
At least one ResourceBlockInfo sub-TLV MUST be present in the WSON
Processing Hop Attribute TLV. No more than two ResourceBlockInfo
sub-TLVs SHOULD be present. Any present ResourceBlockInfo sub-TLVs
MUST be processed in the order received, and extra (unprocessed) sub-
TLVs SHOULD be ignored.
The ResourceBlockInfo field contains several information elements as
defined by [RFC7581]. The following rules apply to the sub-TLV:
o RB Set field can carry one or more RB Identifier. Only the first
RB Identifier listed in the RB Set field SHALL be processed; any
others SHOULD be ignored.
o In the case of unidirectional LSPs, only one ResourceBlockInfo
sub-TLV SHALL be processed, and the I and O bits can be safely
ignored.
Bernstein, et al. Standards Track [Page 8]
RFC 7689 WSON Signaling Extensions November 2015
o In the case of a bidirectional LSP, there MUST be either:
(a) only one ResourceBlockInfo sub-TLV present in a WSON
Processing Hop Attribute TLV, and the bits I and O both set to
1, or
(b) two ResourceBlockInfo sub-TLVs present, one with only the I
bit set and the other with only the O bit set.
o The rest of the information carried within the ResourceBlockInfo
sub-TLV includes the Optical Interface Class List, Input Bit Rate
List, and Processing Capability List. These lists MAY contain one
or more elements. These elements apply equally to both
bidirectional and unidirectional LSPs.
Any violation of these rules detected by a transit or egress node
SHALL be treated as an error and be processed per [RFC7570].
A ResourceBlockInfo sub-TLV can be constructed by a node and added to
an ERO Hop Attributes subobject in order to be processed by
downstream nodes (transit and egress). As defined in [RFC7570], the
R bit reflects the LSP_REQUIRED_ATTRIBUTE and LSP_ATTRIBUTE semantic
defined in [RFC5420], and it SHOULD be set accordingly.
Once a node properly parses a ResourceBlockInfo sub-TLV received in
an ERO Hop Attributes subobject (according to the rules stated above
and in [RFC7570]), the node allocates the indicated resources, e.g.,
the selected regeneration pool, for the LSP. In addition, the node
SHOULD report compliance by adding an RRO Hop Attributes subobject
with the WSON Processing Hop Attribute TLV (and its sub-TLVs)
indicating the utilized resources. ResourceBlockInfo sub-TLVs
carried in an RRO Hop Attributes subobject are subject to [RFC7570]
and standard RRO processing; see [RFC3209].
4.2.2. WavelengthSelection Sub-TLV
Routing + Distributed Wavelength Assignment (R+DWA) is one of the
options defined by [RFC6163]. The output from the routing function
will be a path, but the wavelength will be selected on a hop-by-hop
basis.
As discussed in [RFC6163], the wavelength assignment can be either
for a unidirectional lightpath or for a bidirectional lightpath
constrained to use the same lambda in both directions.
In order to indicate wavelength assignment directionality and
wavelength assignment method, the WavelengthSelection sub-TLV is
carried in the WSON Processing Hop Attribute TLV defined above.
Bernstein, et al. Standards Track [Page 9]
RFC 7689 WSON Signaling Extensions November 2015
The WavelengthSelection sub-TLV value field is defined as:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|W| WA Method | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Where:
W (1 bit): 0 denotes requiring the same wavelength in both
directions; 1 denotes that different wavelengths on both
directions are allowed.
Wavelength Assignment (WA) Method (7 bits):
0: unspecified (any); This does not constrain the WA method used
by a specific node. This value is implied when the
WavelengthSelection sub-TLV is absent.
1: First-Fit. All the wavelengths are numbered, and this WA
method chooses the available wavelength with the lowest index.
2: Random. This WA method chooses an available wavelength
randomly.
3: Least-Loaded (multi-fiber). This WA method selects the
wavelength that has the largest residual capacity on the most
loaded link along the route. This method is used in multi-
fiber networks. If used in single-fiber networks, it is
equivalent to the First-Fit WA method.
4-127: Unassigned.
The processing rules for this TLV are as follows:
If a receiving node does not support the attribute(s), its behaviors
are specified below:
- W bit not supported: a PathErr MUST be generated with the Error
Code "Routing Problem" (24) with error sub-code "Unsupported
WavelengthSelection Symmetry value" (107).
- WA method not supported: a PathErr MUST be generated with the
Error Code "Routing Problem" (24) with error sub-code "Unsupported
Wavelength Assignment value" (108).
Bernstein, et al. Standards Track [Page 10]
RFC 7689 WSON Signaling Extensions November 2015
A WavelengthSelection sub-TLV can be constructed by a node and added
to an ERO Hop Attributes subobject in order to be processed by
downstream nodes (transit and egress). As defined in [RFC7570], the
R bit reflects the LSP_REQUIRED_ATTRIBUTE and LSP_ATTRIBUTE semantic
defined in [RFC5420], and it SHOULD be set accordingly.
Once a node properly parses the WavelengthSelection sub-TLV received
in an ERO Hop Attributes subobject, the node use the indicated
wavelength assignment method (at that hop) for the LSP. In addition,
the node SHOULD report compliance by adding an RRO Hop Attributes
subobject with the WSON Processing Hop Attribute TLV (and its sub-
TLVs) that indicate the utilized method. WavelengthSelection sub-
TLVs carried in an RRO Hop Attributes subobject are subject to
[RFC7570] and standard RRO processing; see [RFC3209].
5. Security Considerations
This document is built on the mechanisms defined in [RFC3473], and
only differs in the specific information communicated. The specific
additional information (optical resource and wavelength selection
properties) is not viewed as substantively changing or adding to the
security considerations of the existing GMPLS signaling protocol
mechanisms. See [RFC3473] for details of the supported security
measures. Additionally, [RFC5920] provides an overview of security
vulnerabilities and protection mechanisms for the GMPLS control
plane.
6. IANA Considerations
IANA has assigned a new value in the existing "Attributes TLV Space"
registry located at
<http://www.iana.org/assignments/rsvp-te-parameters>, as updated by
[RFC7570]:
Type Name Allowed on Allowed on Allowed on Reference
LSP LSP REQUIRED RO LSP
ATTRIBUTES ATTRIBUTES Attribute
Subobject
4 WSON No No Yes RFC 7689
Processing
Hop
Attribute
TLV
Bernstein, et al. Standards Track [Page 11]
RFC 7689 WSON Signaling Extensions November 2015
IANA has created a new registry named "Sub-TLV Types for WSON
Processing Hop Attribute TLV" located at
<http://www.iana.org/assignments/rsvp-te-parameters>.
The following entries have been added:
Value Sub-TLV Type Reference
0 Reserved RFC 7689
1 ResourceBlockInfo RFC 7689
2 WavelengthSelection RFC 7689
All assignments are to be performed via Standards Action or
Specification Required policies as defined in [RFC5226].
IANA has created a new registry named "Values for Wavelength
Assignment Method field in WavelengthSelection Sub-TLV" located at
<http://www.iana.org/assignments/rsvp-te-parameters>.
The following entries have been added:
Value Meaning Reference
0 unspecified RFC 7689
1 First-Fit RFC 7689
2 Random RFC 7689
3 Least-Loaded (multi-fiber) RFC 7689
4-127 Unassigned
All assignments are to be performed via Standards Action or
Specification Required policies as defined in [RFC5226]. The
assignment policy chosen for any specific code point must be clearly
stated in the document that describes the code point so that IANA can
apply the correct policy.
Bernstein, et al. Standards Track [Page 12]
RFC 7689 WSON Signaling Extensions November 2015
IANA has assigned new values in the existing "Sub-Codes - 24 Routing
Problem" registry located at
<http://www.iana.org/assignments/rsvp-parameters>:
Value Description Reference
107 Unsupported WavelengthSelection
symmetry value RFC 7689
108 Unsupported Wavelength Assignment
value RFC 7689
7. References
7.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001,
<http://www.rfc-editor.org/info/rfc3209>.
[RFC3471] Berger, L., Ed., "Generalized Multi-Protocol Label
Switching (GMPLS) Signaling Functional Description", RFC
3471, DOI 10.17487/RFC3471, January 2003,
<http://www.rfc-editor.org/info/rfc3471>.
[RFC3473] Berger, L., Ed., "Generalized Multi-Protocol Label
Switching (GMPLS) Signaling Resource ReserVation Protocol-
Traffic Engineering (RSVP-TE) Extensions", RFC 3473,
DOI 10.17487/RFC3473, January 2003,
<http://www.rfc-editor.org/info/rfc3473>.
[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", BCP 26, RFC 5226,
DOI 10.17487/RFC5226, May 2008,
<http://www.rfc-editor.org/info/rfc5226>.
[RFC5420] Farrel, A., Ed., Papadimitriou, D., Vasseur, JP., and A.
Ayyangarps, "Encoding of Attributes for MPLS LSP
Establishment Using Resource Reservation Protocol Traffic
Engineering (RSVP-TE)", RFC 5420, DOI 10.17487/RFC5420,
February 2009, <http://www.rfc-editor.org/info/rfc5420>.
Bernstein, et al. Standards Track [Page 13]
RFC 7689 WSON Signaling Extensions November 2015
[RFC5511] Farrel, A., "Routing Backus-Naur Form (RBNF): A Syntax
Used to Form Encoding Rules in Various Routing Protocol
Specifications", RFC 5511, DOI 10.17487/RFC5511, April
2009, <http://www.rfc-editor.org/info/rfc5511>.
[RFC6205] Otani, T., Ed., and D. Li, Ed., "Generalized Labels for
Lambda-Switch-Capable (LSC) Label Switching Routers", RFC
6205, DOI 10.17487/RFC6205, March 2011,
<http://www.rfc-editor.org/info/rfc6205>.
[RFC7570] Margaria, C., Ed., Martinelli, G., Balls, S., and B.
Wright, "Label Switched Path (LSP) Attribute in the
Explicit Route Object (ERO)", RFC 7570,
DOI 10.17487/RFC7570, July 2015,
<http://www.rfc-editor.org/info/rfc7570>.
[RFC7581] Bernstein, G., Ed., Lee, Y., Ed., Li, D., Imajuku, W., and
J. Han, "Routing and Wavelength Assignment Information
Encoding for Wavelength Switched Optical Networks", RFC
7581, DOI 10.17487/RFC7581, June 2015,
<http://www.rfc-editor.org/info/rfc7581>.
[RFC7688] Lee, Y., Ed., and G. Bernstein, Ed., "GMPLS OSPF
Enhancement for Signal and Network Element Compatibility
for Wavelength Switched Optical Networks", RFC 7688,
DOI 10.17487/RFC7688, November 2015,
<http://www.rfc-editor.org/info/rfc7688>.
7.2. Informative References
[RFC5920] Fang, L., Ed., "Security Framework for MPLS and GMPLS
Networks", RFC 5920, DOI 10.17487/RFC5920, July 2010,
<http://www.rfc-editor.org/info/rfc5920>.
[RFC6163] Lee, Y., Ed., Bernstein, G., Ed., and W. Imajuku,
"Framework for GMPLS and Path Computation Element (PCE)
Control of Wavelength Switched Optical Networks (WSONs)",
RFC 6163, DOI 10.17487/RFC6163, April 2011,
<http://www.rfc-editor.org/info/rfc6163>.
[RFC7446] Lee, Y., Ed., Bernstein, G., Ed., Li, D., and W. Imajuku,
"Routing and Wavelength Assignment Information Model for
Wavelength Switched Optical Networks", RFC 7446,
DOI 10.17487/RFC7446, February 2015,
<http://www.rfc-editor.org/info/rfc7446>.
Bernstein, et al. Standards Track [Page 14]
RFC 7689 WSON Signaling Extensions November 2015
Acknowledgments
The authors would like to thanks Lou Berger, Cyril Margaria, and Xian
Zhang for their comments and suggestions.
Contributors
Nicola Andriolli
Scuola Superiore Sant'Anna
Pisa, Italy
Email: nick@sssup.it
Alessio Giorgetti
Scuola Superiore Sant'Anna
Pisa, Italy
Email: a.giorgetti@sssup.it
Lin Guo
Key Laboratory of Optical Communication and Lightwave Technologies
Ministry of Education
P.O. Box 128, Beijing University of Posts and Telecommunications
China
Email: guolintom@gmail.com
Yuefeng Ji
Key Laboratory of Optical Communication and Lightwave Technologies
Ministry of Education
P.O. Box 128, Beijing University of Posts and Telecommunications
China
Email: jyf@bupt.edu.cn
Daniel King
Old Dog Consulting
Email: daniel@olddog.co.uk
Bernstein, et al. Standards Track [Page 15]
RFC 7689 WSON Signaling Extensions November 2015
Authors' Addresses
Greg M. Bernstein (editor)
Grotto Networking
Fremont, CA
United States
Phone: (510) 573-2237
Email: gregb@grotto-networking.com
Sugang Xu
National Institute of Information and Communications Technology
4-2-1 Nukui-Kitamachi, Koganei,
Tokyo, 184-8795
Japan
Phone: +81 42-327-6927
Email: xsg@nict.go.jp
Young Lee (editor)
Huawei Technologies
5340 Legacy Dr. Building 3
Plano, TX 75024
United States
Phone: (469) 277-5838
Email: leeyoung@huawei.com
Giovanni Martinelli
Cisco
Via Philips 12
20052 Monza
Italy
Phone: +39 039-209-2044
Email: giomarti@cisco.com
Hiroaki Harai
National Institute of Information and Communications Technology
4-2-1 Nukui-Kitamachi, Koganei,
Tokyo, 184-8795
Japan
Phone: +81 42-327-5418
Email: harai@nict.go.jp
Bernstein, et al. Standards Track [Page 16]
ERRATA
