rfc8155
Internet Engineering Task Force (IETF) P. Patil
Request for Comments: 8155 T. Reddy
Updates: 5766 Cisco
Category: Standards Track D. Wing
ISSN: 2070-1721 April 2017
Traversal Using Relays around NAT (TURN) Server Auto Discovery
Abstract
Current Traversal Using Relays around NAT (TURN) server discovery
mechanisms are relatively static and limited to explicit
configuration. These are usually under the administrative control of
the application or TURN service provider, and not the enterprise,
ISP, or the network in which the client is located. Enterprises and
ISPs wishing to provide their own TURN servers need auto-discovery
mechanisms that a TURN client could use with minimal or no
configuration. This document describes three such mechanisms for
TURN server discovery.
This document updates RFC 5766 to relax the requirement for mutual
authentication in certain cases.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc8155.
Patil, et al. Standards Track [Page 1]
RFC 8155 TURN Server Auto Discovery April 2017
Copyright Notice
Copyright (c) 2017 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Discovery Procedure . . . . . . . . . . . . . . . . . . . . . 4
4. Discovery Using Service Resolution . . . . . . . . . . . . . 5
4.1. Retrieving Domain Name . . . . . . . . . . . . . . . . . 5
4.1.1. DHCP . . . . . . . . . . . . . . . . . . . . . . . . 5
4.1.2. From Own Identity . . . . . . . . . . . . . . . . . . 6
4.2. Resolution . . . . . . . . . . . . . . . . . . . . . . . 6
5. DNS Service Discovery . . . . . . . . . . . . . . . . . . . . 6
5.1. mDNS . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6. Discovery Using Anycast . . . . . . . . . . . . . . . . . . . 7
7. Deployment Considerations . . . . . . . . . . . . . . . . . . 8
7.1. Mobility and Changing IP Addresses . . . . . . . . . . . 8
7.2. Recursively Encapsulated TURN . . . . . . . . . . . . . . 8
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 9
8.1. IPv4 Anycast . . . . . . . . . . . . . . . . . . . . . . 9
8.2. IPv6 Anycast . . . . . . . . . . . . . . . . . . . . . . 9
9. Security Considerations . . . . . . . . . . . . . . . . . . . 10
9.1. Service Resolution . . . . . . . . . . . . . . . . . . . 12
9.2. DNS Service Discovery . . . . . . . . . . . . . . . . . . 12
9.3. Anycast . . . . . . . . . . . . . . . . . . . . . . . . . 13
10. References . . . . . . . . . . . . . . . . . . . . . . . . . 13
10.1. Normative References . . . . . . . . . . . . . . . . . . 13
10.2. Informative References . . . . . . . . . . . . . . . . . 15
Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . 16
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 16
Patil, et al. Standards Track [Page 2]
RFC 8155 TURN Server Auto Discovery April 2017
1. Introduction
TURN [RFC5766] is a protocol that is often used to improve the
connectivity of Peer-to-Peer (P2P) applications (as defined in
Section 2.7 of [RFC5128]). TURN allows a connection to be
established when one or both sides are incapable of a direct P2P
connection. It is an important building block for interactive, real-
time communication using audio, video, collaboration, etc.
While TURN services are extensively used today, the means to
automatically discover TURN servers do not exist. TURN clients are
usually explicitly configured with a well-known TURN server. To
allow TURN applications to operate seamlessly across different types
of networks and encourage the use of TURN without the need for manual
configuration, it is important that there exist an auto-discovery
mechanism for TURN services. Web Real-Time Communication (WebRTC)
[WebRTC-Overview] usages and related extensions, which are mostly
based on web applications, need TURN server discovery mechanisms.
This document describes three discovery mechanisms, so as to maximize
the opportunity for discovery, based on the network in which the TURN
client finds itself. The three discovery mechanisms are:
o A resolution mechanism based on Straightforward-Naming Authority
Pointer (S-NAPTR) resource records in the Domain Name System
(DNS). [RFC5928] describes details on retrieving a list of server
transport addresses from the DNS that can be used to create a TURN
allocation.
o DNS Service Discovery.
o A mechanism based on an anycast address for TURN.
In general, if a client wishes to communicate using one of its
interfaces using a specific IP address family, it SHOULD query the
TURN server(s) that has been discovered for that specific interface
and address family. How to select an interface and IP address family
is out of the scope of this document.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
[RFC2119].
Patil, et al. Standards Track [Page 3]
RFC 8155 TURN Server Auto Discovery April 2017
3. Discovery Procedure
TURN clients, by default, discover TURN server(s) by means of local
or manual TURN configuration (i.e., TURN servers configured at the
system level). Configuration discovered from an application, e.g., a
JavaScript-specified TURN server for Web Real-Time Communication
(WebRTC) [WebRTC-Overview] usages and related extensions, is
considered a local configuration. An implementation may give the
user an opportunity (e.g., by means of configuration file options or
menu items) to specify a TURN server for each address family. A
client can choose auto-discovery in the absence of local
configuration, if local configuration doesn't work or in addition to
local configuration. This document does not offer a recommendation
on server selection.
A TURN client that implements the auto-discovery algorithm, to
discover TURN servers in the attached network, uses the following
mechanisms for discovery:
o Service Resolution: The TURN client attempts to perform TURN
service resolution using the host's DNS domain.
o DNS SD: DNS Service Discovery.
o Anycast: Send TURN Allocation request to the assigned TURN anycast
request for each combination of interface and address family.
Not all TURN servers may be discovered using NAPTR records or DNS SD.
Similarly, not all TURN servers may support anycast. For best
results, a client SHOULD implement all the discovery mechanisms
described above.
The document does not prescribe a strict order that a client must
follow for discovery. An implementation may choose to perform all
the above steps in parallel for discovery OR choose to follow any
desired order and stop the discovery procedure if a mechanism
succeeds.
On hosts with more than one interface or address family (IPv4/v6),
the TURN server discovery procedure has to be performed for each
combination of interface and address family. A client MAY choose to
perform the discovery procedure only for a desired interface/address
combination if the client does not wish to discover a TURN server for
all combinations of interface and address family.
Patil, et al. Standards Track [Page 4]
RFC 8155 TURN Server Auto Discovery April 2017
4. Discovery Using Service Resolution
This mechanism is performed in two steps:
1. A DNS domain name is retrieved for each combination of interface
and address family.
2. Retrieved DNS domain names are then used for S-NAPTR lookups as
per [RFC5928]. Further DNS lookups may be necessary to determine
TURN server IP address(es).
4.1. Retrieving Domain Name
A client has to determine the domain in which it is located. The
following sections provide two possible mechanisms to learn the
domain name, but other means of retrieving domain names may be used,
which are outside the scope of this document, e.g., local
configuration.
Implementations may allow the user to specify a default name that is
used if no specific name has been configured.
4.1.1. DHCP
DHCP can be used to determine the domain name related to an
interface's point of network attachment. Network operators may
provide the domain name to be used for service discovery within an
access network using DHCP. Sections 3.2 and 3.3 of [RFC5986] define
DHCP IPv4 and IPv6 access network domain name options,
OPTION_V4_ACCESS_DOMAIN and OPTION_V6_ACCESS_DOMAIN respectively, to
identify a domain name that is suitable for service discovery within
the access network.
For IPv4, the discovery procedure MUST request the access network
domain name option in a Parameter Request List option, as described
in [RFC2131]. [RFC2132] defines the DHCP IPv4 domain name option;
while this option is less suitable, a client MAY request it if the
access network domain name defined in [RFC5986] is not available.
For IPv6, the discovery procedure MUST request the access network
domain name option in an Options Request Option (ORO) within an
Information-request message, as described in [RFC3315].
If neither option can be retrieved, the procedure fails for this
interface. If a result can be retrieved, it will be used as an input
for S-NAPTR resolution.
Patil, et al. Standards Track [Page 5]
RFC 8155 TURN Server Auto Discovery April 2017
4.1.2. From Own Identity
For a TURN client with an understanding of the protocol mechanics of
calling applications, the client may wish to extract the domain name
from its own identity, i.e, the canonical identifier used to reach
the user.
Example:
SIP : 'sip:alice@example.com'
Bare JID : 'alice@example.com'
email : 'alice@example.com'
'example.com' is retrieved from the above examples.
A client may support multiple users, potentially with different
domains, or a single user utilizing different domains for different
services. The means to choose and extract the domain name may be
different based on the type of identifier, service being used, etc.,
which are outside the scope of this document.
4.2. Resolution
Once the TURN discovery procedure has retrieved domain names, the
resolution mechanism described in [RFC5928] is followed. An S-NAPTR
lookup with the 'RELAY' application service and the desired protocol
tag is made to obtain the information necessary to connect to the
authoritative TURN server within the given domain.
If no TURN-specific S-NAPTR records can be retrieved, the discovery
procedure fails for this domain name (and the corresponding interface
and IP protocol version). If more domain names are known, the
discovery procedure may perform the corresponding S-NAPTR lookups
immediately. However, before retrying a lookup that has failed, a
client must wait a time period that is appropriate for the
encountered error (NXDOMAIN, timeout, etc.).
5. DNS Service Discovery
DNS-based Service Discovery (DNS-SD) [RFC6763] and Multicast DNS
(mDNS) [RFC6762] provide generic solutions for discovering services
available in a local network. DNS-SD/mDNS define a set of naming
rules for certain DNS record types that they use for advertising and
discovering services.
Patil, et al. Standards Track [Page 6]
RFC 8155 TURN Server Auto Discovery April 2017
Section 4.1 of [RFC6763] specifies that a service instance name in
DNS-SD has the following structure:
<Instance> . <Service> . <Domain>
The <Domain> portion specifies the DNS sub-domain where the service
instance is registered. It may be "local.", indicating the mDNS
local domain, or it may be a conventional domain name such as
"example.com.". The <Service> portion of the TURN service instance
name MUST be "_turn._udp" or "_turn._tcp" or "_turns._udp" or
"_turns._tcp", as introduced in [RFC5766].
5.1. mDNS
A TURN client can proactively discover TURN servers being advertised
in the site by multicasting a PTR query to one or all of the
following:
o "_turn._udp.local."
o "_turn._tcp.local"
o "_turns._udp.local."
o "_turns._tcp.local"
A TURN server can send out gratuitous multicast DNS answer packets
whenever it starts up, wakes from sleep, or detects a change in
network configuration. TURN clients receive these gratuitous packets
and cache information contained in it.
6. Discovery Using Anycast
IP anycast can also be used for TURN service discovery. A packet
sent to an anycast address is delivered to the "topologically
nearest" network interface with the anycast address. Using the TURN
anycast address, the only two things that need to be deployed in the
network for discovery are the two things that actually use TURN.
When a client requires TURN services, it sends a TURN Allocation
request to the assigned anycast address. A TURN anycast server
performs checks 1 through 7 discussed in Section 6.2 of [RFC5766].
If all checks pass, the TURN anycast server MUST respond with a 300
(Try Alternate) error as described in Section 2.9 of [RFC5766]; the
response contains the TURN unicast address in the ALTERNATE-SERVER
attribute. For subsequent communication with the TURN server, the
client uses the responding server's unicast address. This has to be
done because two packets addressed to an anycast address may reach
Patil, et al. Standards Track [Page 7]
RFC 8155 TURN Server Auto Discovery April 2017
two different anycast servers. The client, thus, also needs to
ensure that the initial request fits in a single packet. An
implementation may choose to send out every new TURN Allocation
request to the anycast address to discover the closest and the most
optimal unicast address for the TURN server.
7. Deployment Considerations
7.1. Mobility and Changing IP Addresses
A change of IP address on an interface may invalidate the result of
the TURN server discovery procedure. For instance, if the IP address
assigned to a mobile host changes due to host mobility, it may be
required to re-run the TURN server discovery procedure without
relying on earlier gained information. New requests should be made
to the newly learned TURN servers that were learned after TURN the
discovery was re-run. However, if an earlier learned TURN server is
still accessible using the new IP address, procedures described for
mobility using TURN defined in [RFC8016] can be used for ongoing
streams.
7.2. Recursively Encapsulated TURN
WebRTC endpoints SHOULD treat any TURN server discovered through the
mechanisms described in this specification as an enterprise/gateway
or access network server, in accordance with Recursively Encapsulated
TURN [RETURN].
Patil, et al. Standards Track [Page 8]
RFC 8155 TURN Server Auto Discovery April 2017
8. IANA Considerations
8.1. IPv4 Anycast
IANA has assigned a single IPv4 address from the 192.0.0.0/24 prefix
and registered it in the "IANA IPv4 Special-Purpose Address Registry"
[RFC6890].
+----------------------+-------------------------------------------+
| Attribute | Value |
+----------------------+-------------------------------------------+
| Address Block | 192.0.0.10/32 |
| Name | Traversal Using Relays around NAT Anycast |
| RFC | RFC 8155 |
| Allocation Date | 2017-02 |
| Termination Date | N/A |
| Source | True |
| Destination | True |
| Forwardable | True |
| Global | True |
| Reserved-by-Protocol | False |
+----------------------+-------------------------------------------+
8.2. IPv6 Anycast
IANA has assigned a single IPv6 address from the 2001:0000::/23
prefix and registered it in the "IANA IPv6 Special-Purpose Address
Registry" [RFC6890].
+----------------------+-------------------------------------------+
| Attribute | Value |
+----------------------+-------------------------------------------+
| Address Block | 2001:1::2/128 |
| Name | Traversal Using Relays around NAT Anycast |
| RFC | RFC 8155 |
| Allocation Date | 2017-02 |
| Termination Date | N/A |
| Source | True |
| Destination | True |
| Forwardable | True |
| Global | True |
| Reserved-by-Protocol | False |
+----------------------+-------------------------------------------+
Patil, et al. Standards Track [Page 9]
RFC 8155 TURN Server Auto Discovery April 2017
9. Security Considerations
Use of Session Traversal Utilities for NAT (STUN) [RFC5389]
authentication is OPTIONAL for TURN servers provided by the local
network or by the access network. A network-provided TURN server MAY
be configured to accept Allocation requests without STUN
authentication, and a TURN client MAY be configured to accept
Allocation success responses without STUN authentication from a
network-provided TURN server.
Making STUN authentication optional is a downgrade of a MUST level
requirement defined in [RFC5766]. The downgrade allows TURN servers
provided by the local or access network to accept Allocation requests
from new and/or guest users in the network who do not necessarily
possess long term credentials for STUN authentication. The intention
in such deployments is to provide TURN services to all users in the
local or access network. However, this opens up a TURN server to a
variety of attacks described in Section 17 of [RFC5766]. A TURN
server in such cases must be configured to only process STUN requests
from the trusted local network or subscribers of the access network.
Operational measures must be taken in order to protect the TURN
server; some of these measures include, but are not limited to,
access control by means of access lists, firewalls, subscriber quota
limits, ingress filtering, etc.
A TURN client in the absence of the STUN long-term credential
mechanism [RFC5389] or the STUN Extension for Third-Party
Authorization [RFC7635] MUST use (D)TLS unless it trusts the network
infrastructure to defend against attacks discussed in [RFC5766]. It
is RECOMMENDED that the TURN client use one of the following
techniques with (D)TLS to validate the TURN server:
o For certificate-based authentication, a pre-populated trust anchor
store [RFC6024] allows a TURN client to perform path validation
for the server certificate obtained during the (D)TLS handshake.
If the client used a domain name to discover the TURN server, that
domain name also provides a mechanism for validation of the TURN
server. The client MUST use the rules and guidelines given in
Section 6 of [RFC6125] to validate the TURN server identity.
o Certification authorities that issue TURN server certificates
SHOULD support the CN-ID, DNS-ID, SRV-ID, and URI-ID identifier
types. TURN service providers SHOULD prefer the use of DNS-ID,
SRV-ID, and URI-ID over CN-ID identifier types in certificate
requests (as described in Section 2.3 from [RFC6125]) and the
wildcard character '*' SHOULD NOT be included in the presented
identifier.
Patil, et al. Standards Track [Page 10]
RFC 8155 TURN Server Auto Discovery April 2017
o For TURN servers that don't have a certificate trust chain (e.g.,
because they are on a home network or a corporate network), a
configured list of TURN servers can contain the Subject Public Key
Info (SPKI) fingerprint of the TURN servers. The public key is
used for the same reasons HTTP pinning [RFC7469] uses the public
key.
o Raw public key-based authentication, as defined in [RFC7250],
could also be used to authenticate a TURN server.
An auto-discovered TURN server is considered to be only as trusted as
the path between the client and the TURN server. In order to safely
use auto-discovered TURN servers for sessions with 'strict privacy'
requirements, the user needs to be able to define privacy criteria
(e.g., a trusted list of servers, networks, or domains) that are
considered acceptable for such traffic. Any discovered TURN server
outside the criteria is considered untrusted and therefore MUST NOT
be used for privacy-sensitive communication.
In some auto-discovery scenarios, it might not be possible for the
TURN client to use (D)TLS authentication to validate the TURN server.
However, fallback to clear text in such cases could leave the TURN
client open to on-path injection of spoofed TURN messages. A TURN
client could fall back to encryption-only (D)TLS when (D)TLS
authentication is not available but MUST NOT fall back without
explicit administrator choice. Another reason to fall back to
encryption-only is for privacy, which is analogous to SMTP
opportunistic encryption [RFC7435] where one does not require privacy
but one desires privacy when possible.
In order to allow the TURN client to fall back to (D)TLS as described
above, a TURN server that does not require either STUN long-term
authentication [RFC5389] or STUN Extension for Third Party
Authorization [RFC7635] MUST support (D)TLS and, if the network
infrastructure is capable of defending against attacks discussed in
[RFC5766], then the TURN server MAY allow fallback to clear text.
A TURN client could fall back to clear text if it does not support
unauthenticated (D)TLS but MUST NOT fall back without explicit
administrator choice. Fallback to clear text is NOT RECOMMENDED
because it makes the client more susceptible to man-in-the-middle
attacks and on-path packet injection.
Patil, et al. Standards Track [Page 11]
RFC 8155 TURN Server Auto Discovery April 2017
9.1. Service Resolution
The primary attack against the methods described in this document is
one that would lead to impersonation of a TURN server. An attacker
could attempt to compromise the S-NAPTR resolution. Security
considerations described in [RFC5928] are applicable here as well.
In addition to considerations related to S-NAPTR, it is important to
recognize that the output of this is entirely dependent on its input.
An attacker who can control the domain name can also control the
final result. Because more than one method can be used to determine
the domain name, a host implementation needs to consider attacks
against each of the methods that are used.
If DHCP is used, the integrity of DHCP options is limited by the
security of the channel over which they are provided. Physical
security and separation of DHCP messages from other packets are
commonplace methods that can reduce the possibility of attack within
an access network; alternatively, DHCP authentication [RFC3188] can
provide a degree of protection against modification. When using DHCP
discovery, clients are encouraged to use unicast DHCP INFORM queries
instead of broadcast queries, which are more easily spoofed in
insecure networks.
9.2. DNS Service Discovery
Since DNS-SD is just a specification for how to name and use records
in the existing DNS system, it has no specific additional security
requirements over and above those that already apply to DNS queries
and DNS updates. For DNS queries, DNS Security Extensions (DNSSEC)
[RFC4033] should be used where the authenticity of information is
important. For DNS updates, secure updates [RFC2136] [RFC3007]
should generally be used to control which clients have permission to
update DNS records.
For mDNS, in addition to what has been described above, a principal
security threat is a security threat inherent to IP multicast routing
and any application that runs on it. A rogue system can advertise
that it is a TURN server. Discovery of such rogue systems as TURN
servers, in itself, is not a security threat if there is a means for
the TURN client to authenticate and authorize the discovered TURN
servers.
Patil, et al. Standards Track [Page 12]
RFC 8155 TURN Server Auto Discovery April 2017
9.3. Anycast
In a network without any TURN server that is aware of the TURN
anycast address, outgoing TURN requests could leak out onto the
external Internet, possibly revealing information.
Using an IANA-assigned well-known TURN anycast address enables border
gateways to block such outgoing packets. In the default-free zone,
routers should be configured to drop such packets. Such
configuration can occur naturally via BGP messages advertising that
no route exists to said address.
Sensitive clients that do not wish to leak information about their
presence can set an IP TTL on their TURN requests that limits how far
they can travel into the public Internet.
10. References
10.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC2131] Droms, R., "Dynamic Host Configuration Protocol",
RFC 2131, DOI 10.17487/RFC2131, March 1997,
<http://www.rfc-editor.org/info/rfc2131>.
[RFC2132] Alexander, S. and R. Droms, "DHCP Options and BOOTP Vendor
Extensions", RFC 2132, DOI 10.17487/RFC2132, March 1997,
<http://www.rfc-editor.org/info/rfc2132>.
[RFC2136] Vixie, P., Ed., Thomson, S., Rekhter, Y., and J. Bound,
"Dynamic Updates in the Domain Name System (DNS UPDATE)",
RFC 2136, DOI 10.17487/RFC2136, April 1997,
<http://www.rfc-editor.org/info/rfc2136>.
[RFC3007] Wellington, B., "Secure Domain Name System (DNS) Dynamic
Update", RFC 3007, DOI 10.17487/RFC3007, November 2000,
<http://www.rfc-editor.org/info/rfc3007>.
[RFC3315] Droms, R., Ed., Bound, J., Volz, B., Lemon, T., Perkins,
C., and M. Carney, "Dynamic Host Configuration Protocol
for IPv6 (DHCPv6)", RFC 3315, DOI 10.17487/RFC3315, July
2003, <http://www.rfc-editor.org/info/rfc3315>.
Patil, et al. Standards Track [Page 13]
RFC 8155 TURN Server Auto Discovery April 2017
[RFC4033] Arends, R., Austein, R., Larson, M., Massey, D., and S.
Rose, "DNS Security Introduction and Requirements",
RFC 4033, DOI 10.17487/RFC4033, March 2005,
<http://www.rfc-editor.org/info/rfc4033>.
[RFC5389] Rosenberg, J., Mahy, R., Matthews, P., and D. Wing,
"Session Traversal Utilities for NAT (STUN)", RFC 5389,
DOI 10.17487/RFC5389, October 2008,
<http://www.rfc-editor.org/info/rfc5389>.
[RFC5766] Mahy, R., Matthews, P., and J. Rosenberg, "Traversal Using
Relays around NAT (TURN): Relay Extensions to Session
Traversal Utilities for NAT (STUN)", RFC 5766,
DOI 10.17487/RFC5766, April 2010,
<http://www.rfc-editor.org/info/rfc5766>.
[RFC5928] Petit-Huguenin, M., "Traversal Using Relays around NAT
(TURN) Resolution Mechanism", RFC 5928,
DOI 10.17487/RFC5928, August 2010,
<http://www.rfc-editor.org/info/rfc5928>.
[RFC5986] Thomson, M. and J. Winterbottom, "Discovering the Local
Location Information Server (LIS)", RFC 5986,
DOI 10.17487/RFC5986, September 2010,
<http://www.rfc-editor.org/info/rfc5986>.
[RFC6024] Reddy, R. and C. Wallace, "Trust Anchor Management
Requirements", RFC 6024, DOI 10.17487/RFC6024, October
2010, <http://www.rfc-editor.org/info/rfc6024>.
[RFC6762] Cheshire, S. and M. Krochmal, "Multicast DNS", RFC 6762,
DOI 10.17487/RFC6762, February 2013,
<http://www.rfc-editor.org/info/rfc6762>.
[RFC6763] Cheshire, S. and M. Krochmal, "DNS-Based Service
Discovery", RFC 6763, DOI 10.17487/RFC6763, February 2013,
<http://www.rfc-editor.org/info/rfc6763>.
[RFC6890] Cotton, M., Vegoda, L., Bonica, R., Ed., and B. Haberman,
"Special-Purpose IP Address Registries", BCP 153,
RFC 6890, DOI 10.17487/RFC6890, April 2013,
<http://www.rfc-editor.org/info/rfc6890>.
[RFC7250] Wouters, P., Ed., Tschofenig, H., Ed., Gilmore, J.,
Weiler, S., and T. Kivinen, "Using Raw Public Keys in
Transport Layer Security (TLS) and Datagram Transport
Layer Security (DTLS)", RFC 7250, DOI 10.17487/RFC7250,
June 2014, <http://www.rfc-editor.org/info/rfc7250>.
Patil, et al. Standards Track [Page 14]
RFC 8155 TURN Server Auto Discovery April 2017
[RFC7635] Reddy, T., Patil, P., Ravindranath, R., and J. Uberti,
"Session Traversal Utilities for NAT (STUN) Extension for
Third-Party Authorization", RFC 7635,
DOI 10.17487/RFC7635, August 2015,
<http://www.rfc-editor.org/info/rfc7635>.
10.2. Informative References
[RETURN] Schwartz, B. and J. Uberti, "Recursively Encapsulated TURN
(RETURN) for Connectivity and Privacy in WebRTC", Work in
Progress, draft-ietf-rtcweb-return-02, March 2017.
[RFC3188] Hakala, J., "Using National Bibliography Numbers as
Uniform Resource Names", RFC 3188, DOI 10.17487/RFC3188,
October 2001, <http://www.rfc-editor.org/info/rfc3188>.
[RFC5128] Srisuresh, P., Ford, B., and D. Kegel, "State of Peer-to-
Peer (P2P) Communication across Network Address
Translators (NATs)", RFC 5128, DOI 10.17487/RFC5128, March
2008, <http://www.rfc-editor.org/info/rfc5128>.
[RFC6125] Saint-Andre, P. and J. Hodges, "Representation and
Verification of Domain-Based Application Service Identity
within Internet Public Key Infrastructure Using X.509
(PKIX) Certificates in the Context of Transport Layer
Security (TLS)", RFC 6125, DOI 10.17487/RFC6125, March
2011, <http://www.rfc-editor.org/info/rfc6125>.
[RFC7435] Dukhovni, V., "Opportunistic Security: Some Protection
Most of the Time", RFC 7435, DOI 10.17487/RFC7435,
December 2014, <http://www.rfc-editor.org/info/rfc7435>.
[RFC7469] Evans, C., Palmer, C., and R. Sleevi, "Public Key Pinning
Extension for HTTP", RFC 7469, DOI 10.17487/RFC7469, April
2015, <http://www.rfc-editor.org/info/rfc7469>.
[RFC8016] Reddy, T., Wing, D., Patil, P., and P. Martinsen,
"Mobility with Traversal Using Relays around NAT (TURN)",
RFC 8016, DOI 10.17487/RFC8016, November 2016,
<http://www.rfc-editor.org/info/rfc8016>.
[WebRTC-Overview]
Alvestrand, H., "Overview: Real Time Protocols for
Browser-based Applications", Work in Progress,
draft-ietf-rtcweb-overview-18, March 2017.
Patil, et al. Standards Track [Page 15]
RFC 8155 TURN Server Auto Discovery April 2017
Acknowledgements
The authors would like to thank Simon Perrault, Paul Kyzivat, Troy
Shields, Eduardo Gueiros, Ted Hardie, Bernard Aboba, Karl Stahl,
Brian Weis, Ralph Dromes, Ben Campbell, Suresh Krishnan, and Brandon
Williams for their review and valuable comments. Thanks to Adam
Roach for his detailed review and suggesting DNS Service Discovery as
an additional discovery mechanism.
Authors' Addresses
Prashanth Patil
Cisco Systems, Inc.
Email: praspati@cisco.com
Tirumaleswar Reddy
Cisco Systems, Inc.
Cessna Business Park, Varthur Hobli
Sarjapur Marathalli Outer Ring Road
Bangalore, Karnataka 560103
India
Email: tireddy@cisco.com
Dan Wing
United States America
Email: dwing-ietf@fuggles.com
Patil, et al. Standards Track [Page 16]
ERRATA
